Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹3.9 LAdmitted-Finance 24A LAJPAT NAGAR NEAR BUS STAND YAMUNA NAGAR | YAMUNANAGAR | HARYANA | 133103 | ₹3.9 L | L1 | Admitted-Finance |
| 2 | Rejected-Technical T C NO 20 1197 NEAR DOORADARSGAN KENDRA KUDAPPANAKUNNU THIRUVANANTHAPURAM | THIRUVANANTHAPURAM | THIRUVANANTHAPURAM | KERALA | 695043 | - | - | Rejected-Technical Technically disqualified |
| Sl No | Description | Qty | Unit | Khalsa Exports Pvt. Ltd. L1 |
|---|---|---|---|---|
| 1.00Outdoor gym equipments | ||||
| 1.01 | OD252260/2025-2026 : Horse Rider - Supply and Installation of Horse Rider having the following specifications:
Dimensions: (L X W X H) 1140 x 400 x 1400 mm. Main frame - Ø 114 mm OD B class GI pipe. Foundation
plate M.S. round plate of Ø 250 mm & 8 mm thick. Foundation cover cap - dome shape of PP / NYLON /HDPE material. Remaining frame Is made by Ø 48 mm OD ?B? class GI pipe. Seat frame ?Is made by Ø 48mm OD ?B? class GI pipe. Seat position must be horizontal to 110 -120 degree. Link - made up of Ø 48 mm OD ?B? Class G.I. pipe. Angle between link and ground position is 10-20 degree. Handle - Ø 33 mm OD ?B? Class GI pipe. Paddle vertical support - Ø 60 mm OD ?B? Class GI pipe. Handle frame- Ø 42 mm OD ?B? Class GI pipe dually bending design. Foot pipe - Ø 33 mm OD ?B? Class GI pipe. Support frame ? 10 mm thick MS flat is used. Seat- Dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material HDPE.
Bearing bush closing cap ? PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft.
Foundation stool is embedded in C.C. stock below ground level. Bearing - Use is 6005 permanent lubricated reputed brand.
Bearing bushes - Ø 60mm OD seamless pipe. Pin ? Made of Ø 25 mm M.S. bright bar. Grips - High quality rubber Ø 46 mm OD. Circlips ? A 24 circlips are used for assembly. Coating - best quality of powder coating 60 to 70 micron. Safety Instructions and Exercise chart - start &finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | 1 | no | 52,000 ₹52,000 Lowest |
| 1.02 | OD252261/2025-2026 : Back Extension - Supply and Installation of Back Extension having the following specifications: Dimensions: (L X W X H) 1060 x 730 x 990 mm. Main frame - Made from Ø 88 mm OD ?B?
Class G.I. pipe. Foundation plate ? M.S. round plate of Ø 250 mm & 8 mm thick. Leg Support - Ø 42 mm OD ?B? G.I Pipe. Seat rest pipe ? Ø 42 mm OD ?B? Class G.I Pipe. Handle pipe ? Ø 33 mm OD ?B? Class G.I Pipe.
Footrest - Cast iron 124 x 296 x 5 mm thick and M.S plate of 3 mm thick used to support it. Footrest pipe ? Ø 42 mm OD ?B? Class G.I Pipe and 80 x 40 mm MS rectangular pipe. Closing cap ?
PP / NYLON / HDPE material. Seat ? 360 x 300 x 2 mm thick M.S. seat with corner fillet for safety. Grips - High quality rubber Ø 46 mm OD. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | 1 | no | 52,000 ₹52,000 Lowest |
| 1.03 | OD252262/2025-2026 : Cross Trainer (Double) - Supply and Installation of Double Cross Trainer having the following specifications: Dimensions: (L X W X H) 2280 x 550 x 1650 mm. Main frame- Made of Ø 88 mm OD ?B? class GI pipe dually bending design. Foundation plate ? M.S. round plate of Ø 250 mm & 8 mm thick. Paddle vertical support - Ø 42 mm OD ?B? Class GI pipe. Handle - Ø 33 mm OD ?B?
Class GI pipe dually bending design. Leg movement frame ? 50 mm x 50 mm x 2 mm thick square pipe. Footrest - cast iron 124 x
296 x 5 mm thick and M.S. plate of 2 mm thick use for to support it. Top Closing cap ? dome shape made by PP / NYLON / HDPE material. Closing cap?s? PP / NYLON / HDPE material.
Foundation stool: Made from main pipe Ø 88 mm OD B class G.I. pipe. and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft.
Foundation stool is embedded in C.C. stock below ground level. Grips - High quality rubber. Bearing- Use is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60mm OD seamless pipe. Pin ?Made of Ø 25mm M.S. bright bar. Circlips ? A 24 circlips are used for assembly. Coating - best quality of powder coating 80-100 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | 1 | no | 52,000 ₹52,000 Lowest |
| 1.04 | OD252265/2025-2026 : Rower - Supply and Installation of Rower having the following specifications: Dimensions: (L X W X H) = 1472 x 915 x 1040 mm. Upper and bottom pipes - Ø 88 mm OD ?B? Class GI pipe.
Foundation plate ?M.S. round plate of Ø 250 mm & 8 mm thick. Handle - Ø 33 mm OD ?B? Class G.I pipe.
Angle between handle and horizontal surface is 75 - 80 degree. Linkages ? Ø 48 mm OD ?B? Class G.I. pipe.
Seat & back rest ? 380 x 275 x 60mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert
wall thickness 3 to 4 mm. Foot resting pipe - Ø 60 mm OD ?B? Class G.I. pipe. End Closing cap ? dome shape made by PP / NYLON / HDPE material. Closing caps ? PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø250 mm & 8mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft.
Foundation stool is embedded in C.C. stock below ground level. Pin ? Ø 25 mm M.S. bright bar pin. Circlips?
A 24 circlips are used for assembly. Bearing bushes - Ø 60 mm OD seamless pipe / Bar. Bearing- use is 6005 permanent lubricated reputed brands. Grips ? high quality rubber 46 mm OD. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on
product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | 1 | no | 52,000 ₹52,000 Lowest |
| 1.05 | OD252266/2025-2026 : Leg Press (Double) -Supply and Installation of Double Leg Press having the following specifications: Dimensions: (L X W X H) = 1676 x 400 x1500 mm. Main frame - Ø 114 mm OD ?B? class GI pipe. Foundation plate ? M.S. round plate of Ø 250 mm & 8 mm thick. Foundations cover cap - dome shape of PP / NYLON / HDPE material. Link - is Ø 60 mm OD ?B? Class GI pipe. Seat frame - Ø 42 mm OD ?B? Class GI pipe. Leg Press back rest should be angled in 120 -130 degree. Foot rest - cast iron 124 x 296 x 5 mm thick and M.S plate of 2 mm thick use to support it. Seat & back rest ? 380 x 275 x 60 mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert wall thickness 3 to 4 mm. Link connected with frame by 8 mm thick laser cutting MS profile. Top Closing cap ? dome shape made by PP / NYLON / HDPE material.
Closing cap?s- PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C.
stock below ground level. Bearing- use is 6005 permanent lubricated reputed brand. Pin? Ø 25 mm M.S. bright bar pin. Bearing bushes - Ø 60 mm OD seamless pipe. Circlip? A 24 circlips are used for assembly. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | 1 | no | 52,000 ₹52,000 Lowest |
| 1.06 | OD252267/2025-2026 : Triple Twister - Supply and Installation of Triple Twister (Standing position - 2 and Seating position - 1) having the following specifications: Dimensions: (L X W X H) 1500 x 1500 x 1420 mm.
Main frame ? Ø 114 mm OD ?B? class GI pipe. Foundation plate ? M.S. round plate of Ø 250 mm & 8 mm thick. Seat plate support ? Ø 60 mm OD ?B? Class G.I Pipe.
Seating ring - Ø 33 mm OD ?B? Class G.I Pipe
made by rolling. Seating ring support - Ø 33 mm OD ?B? Class G.I Pipe. Remaining frame ? Is made by 100 x 50 x 2.5 mm rectangular pipe. Standing plate- Ø 300 mm OD X 10 mm thick M.S. plate. Seating plate- Ø 300 mm OD X 10 mm thick M.S. plate. Seating seat position and other two standing position plates are fixed 120 degrees each from other. Handle ? Ø 33 mm ?B? Class G.I. Pipe made by rolling. Top Closing cap ? Dome
shape made by PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top.
Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing - Used is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60 mm OD seamless pipe. Pin ? Made up of Ø 25mm M.S. bright bar. Circlips? A 24 circlips are used for assembly. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | 1 | no | 52,000 ₹52,000 Lowest |
| 1.07 | OD252268/2025-2026 : Chest Press (Double) - Supply and Installation of Double Chest Press having the following specifications: Dimensions: (L X W X H) 1955 x 710 x 1900 mm. Main center pipe - Ø 114 mm OD
?B? class GI pipe. Foundation plate ?M.S. round plate of Ø 250mm & 8 mm thick. Foundations cover capdome shape of PP / NYLON / HDPE material. Remaining frame - made up of Ø 48 mm OD ?B? Class G.I. pipe.
Handle - Made up of Ø48mm OD ?B? Class G.I. pipe. Link - made up of Ø 48 mm OD ?B? Class G.I. pipe. Seat & back rest ? 380 X 275 X 60 mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert wall thickness 3 to 4 mm. Bearing bush Closing cap?s? PP / NYLON / HDPE material.
Handle must be connected with frame by 8 MM laser cutting MS profile. Top Closing cap ? dome shape made by PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing - Use is 6005 permanent lubricated reputed brands. Pin ? Made up of Ø 25 mm M.S. bright bar pin. Bearing bushes -
Ø 60 mm OD seamless pipe. Grips - High quality rubber Ø 46 mm OD. Circlips?A 24 circlips are used for assembly. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be
applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | 1 | no | 52,000 ₹52,000 Lowest |
| 2.00Sports equipments | ||||
| 2.01 | OD252282/2025-2026 : Supply of Football- Brand: Nivia or similar make, Model: Shining star or Similar make | 4 | no | 1,000 ₹4,000 Lowest |
Tender Value
₹4.6 L
EMD Value
₹11,650
Closing Date
18 Apr 2026, 3:00 pmClosed
The Chief Engineer, Sports Kerala Foundation
Jimmy George Indoor Stadium, Vellayambalam, Thiruvananthapuram
Supply and Installation of Outdoor Gym and Sports equipment
2026_SKF_825957_4
421/SKF/CE/2025-26
Open Tender
Equipments
Item Rate
60 days
Thiruvananthapuram
Please refer tender document
10 documents required · 10 mandatory
₹1,121
₹11,650
30 Jun 2026
6 Apr 2026
20 Apr 2026
6 Apr 2026
18 Apr 2026
6 Apr 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1Outdoor gym equipments | |||||
| 1.01 | OD252260/2025-2026 : Horse Rider - Supply and Installation of Horse Rider having the following specifications:
Dimensions: (L X W X H) 1140 x 400 x 1400 mm. Main frame - Ø 114 mm OD B class GI pipe. Foundation
plate M.S. round plate of Ø 250 mm & 8 mm thick. Foundation cover cap - dome shape of PP / NYLON /HDPE material. Remaining frame Is made by Ø 48 mm OD ?B? class GI pipe. Seat frame ?Is made by Ø 48mm OD ?B? class GI pipe. Seat position must be horizontal to 110 -120 degree. Link - made up of Ø 48 mm OD ?B? Class G.I. pipe. Angle between link and ground position is 10-20 degree. Handle - Ø 33 mm OD ?B? Class GI pipe. Paddle vertical support - Ø 60 mm OD ?B? Class GI pipe. Handle frame- Ø 42 mm OD ?B? Class GI pipe dually bending design. Foot pipe - Ø 33 mm OD ?B? Class GI pipe. Support frame ? 10 mm thick MS flat is used. Seat- Dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material HDPE.
Bearing bush closing cap ? PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft.
Foundation stool is embedded in C.C. stock below ground level. Bearing - Use is 6005 permanent lubricated reputed brand.
Bearing bushes - Ø 60mm OD seamless pipe. Pin ? Made of Ø 25 mm M.S. bright bar. Grips - High quality rubber Ø 46 mm OD. Circlips ? A 24 circlips are used for assembly. Coating - best quality of powder coating 60 to 70 micron. Safety Instructions and Exercise chart - start &finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | - | no | - | - |
| 1.02 | OD252261/2025-2026 : Back Extension - Supply and Installation of Back Extension having the following specifications: Dimensions: (L X W X H) 1060 x 730 x 990 mm. Main frame - Made from Ø 88 mm OD ?B?
Class G.I. pipe. Foundation plate ? M.S. round plate of Ø 250 mm & 8 mm thick. Leg Support - Ø 42 mm OD ?B? G.I Pipe. Seat rest pipe ? Ø 42 mm OD ?B? Class G.I Pipe. Handle pipe ? Ø 33 mm OD ?B? Class G.I Pipe.
Footrest - Cast iron 124 x 296 x 5 mm thick and M.S plate of 3 mm thick used to support it. Footrest pipe ? Ø 42 mm OD ?B? Class G.I Pipe and 80 x 40 mm MS rectangular pipe. Closing cap ?
PP / NYLON / HDPE material. Seat ? 360 x 300 x 2 mm thick M.S. seat with corner fillet for safety. Grips - High quality rubber Ø 46 mm OD. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | - | no | - | - |
| 1.03 | OD252262/2025-2026 : Cross Trainer (Double) - Supply and Installation of Double Cross Trainer having the following specifications: Dimensions: (L X W X H) 2280 x 550 x 1650 mm. Main frame- Made of Ø 88 mm OD ?B? class GI pipe dually bending design. Foundation plate ? M.S. round plate of Ø 250 mm & 8 mm thick. Paddle vertical support - Ø 42 mm OD ?B? Class GI pipe. Handle - Ø 33 mm OD ?B?
Class GI pipe dually bending design. Leg movement frame ? 50 mm x 50 mm x 2 mm thick square pipe. Footrest - cast iron 124 x
296 x 5 mm thick and M.S. plate of 2 mm thick use for to support it. Top Closing cap ? dome shape made by PP / NYLON / HDPE material. Closing cap?s? PP / NYLON / HDPE material.
Foundation stool: Made from main pipe Ø 88 mm OD B class G.I. pipe. and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft.
Foundation stool is embedded in C.C. stock below ground level. Grips - High quality rubber. Bearing- Use is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60mm OD seamless pipe. Pin ?Made of Ø 25mm M.S. bright bar. Circlips ? A 24 circlips are used for assembly. Coating - best quality of powder coating 80-100 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | - | no | - | - |
| 1.04 | OD252265/2025-2026 : Rower - Supply and Installation of Rower having the following specifications: Dimensions: (L X W X H) = 1472 x 915 x 1040 mm. Upper and bottom pipes - Ø 88 mm OD ?B? Class GI pipe.
Foundation plate ?M.S. round plate of Ø 250 mm & 8 mm thick. Handle - Ø 33 mm OD ?B? Class G.I pipe.
Angle between handle and horizontal surface is 75 - 80 degree. Linkages ? Ø 48 mm OD ?B? Class G.I. pipe.
Seat & back rest ? 380 x 275 x 60mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert
wall thickness 3 to 4 mm. Foot resting pipe - Ø 60 mm OD ?B? Class G.I. pipe. End Closing cap ? dome shape made by PP / NYLON / HDPE material. Closing caps ? PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø250 mm & 8mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft.
Foundation stool is embedded in C.C. stock below ground level. Pin ? Ø 25 mm M.S. bright bar pin. Circlips?
A 24 circlips are used for assembly. Bearing bushes - Ø 60 mm OD seamless pipe / Bar. Bearing- use is 6005 permanent lubricated reputed brands. Grips ? high quality rubber 46 mm OD. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on
product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | - | no | - | - |
| 1.05 | OD252266/2025-2026 : Leg Press (Double) -Supply and Installation of Double Leg Press having the following specifications: Dimensions: (L X W X H) = 1676 x 400 x1500 mm. Main frame - Ø 114 mm OD ?B? class GI pipe. Foundation plate ? M.S. round plate of Ø 250 mm & 8 mm thick. Foundations cover cap - dome shape of PP / NYLON / HDPE material. Link - is Ø 60 mm OD ?B? Class GI pipe. Seat frame - Ø 42 mm OD ?B? Class GI pipe. Leg Press back rest should be angled in 120 -130 degree. Foot rest - cast iron 124 x 296 x 5 mm thick and M.S plate of 2 mm thick use to support it. Seat & back rest ? 380 x 275 x 60 mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert wall thickness 3 to 4 mm. Link connected with frame by 8 mm thick laser cutting MS profile. Top Closing cap ? dome shape made by PP / NYLON / HDPE material.
Closing cap?s- PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C.
stock below ground level. Bearing- use is 6005 permanent lubricated reputed brand. Pin? Ø 25 mm M.S. bright bar pin. Bearing bushes - Ø 60 mm OD seamless pipe. Circlip? A 24 circlips are used for assembly. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | - | no | - | - |
| 1.06 | OD252267/2025-2026 : Triple Twister - Supply and Installation of Triple Twister (Standing position - 2 and Seating position - 1) having the following specifications: Dimensions: (L X W X H) 1500 x 1500 x 1420 mm.
Main frame ? Ø 114 mm OD ?B? class GI pipe. Foundation plate ? M.S. round plate of Ø 250 mm & 8 mm thick. Seat plate support ? Ø 60 mm OD ?B? Class G.I Pipe.
Seating ring - Ø 33 mm OD ?B? Class G.I Pipe
made by rolling. Seating ring support - Ø 33 mm OD ?B? Class G.I Pipe. Remaining frame ? Is made by 100 x 50 x 2.5 mm rectangular pipe. Standing plate- Ø 300 mm OD X 10 mm thick M.S. plate. Seating plate- Ø 300 mm OD X 10 mm thick M.S. plate. Seating seat position and other two standing position plates are fixed 120 degrees each from other. Handle ? Ø 33 mm ?B? Class G.I. Pipe made by rolling. Top Closing cap ? Dome
shape made by PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top.
Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing - Used is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60 mm OD seamless pipe. Pin ? Made up of Ø 25mm M.S. bright bar. Circlips? A 24 circlips are used for assembly. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | - | no | - | - |
| 1.07 | OD252268/2025-2026 : Chest Press (Double) - Supply and Installation of Double Chest Press having the following specifications: Dimensions: (L X W X H) 1955 x 710 x 1900 mm. Main center pipe - Ø 114 mm OD
?B? class GI pipe. Foundation plate ?M.S. round plate of Ø 250mm & 8 mm thick. Foundations cover capdome shape of PP / NYLON / HDPE material. Remaining frame - made up of Ø 48 mm OD ?B? Class G.I. pipe.
Handle - Made up of Ø48mm OD ?B? Class G.I. pipe. Link - made up of Ø 48 mm OD ?B? Class G.I. pipe. Seat & back rest ? 380 X 275 X 60 mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert wall thickness 3 to 4 mm. Bearing bush Closing cap?s? PP / NYLON / HDPE material.
Handle must be connected with frame by 8 MM laser cutting MS profile. Top Closing cap ? dome shape made by PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing - Use is 6005 permanent lubricated reputed brands. Pin ? Made up of Ø 25 mm M.S. bright bar pin. Bearing bushes -
Ø 60 mm OD seamless pipe. Grips - High quality rubber Ø 46 mm OD. Circlips?A 24 circlips are used for assembly. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be
applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) | - | no | - | - |
| 2Sports equipments | |||||
| 2.01 | OD252282/2025-2026 : Supply of Football- Brand: Nivia or similar make, Model: Shining star or Similar make | - | no | - | - |
stage.html
html • 0.03 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.37 MB
Tenderdoc.pdf
Tender Documents • 1.32 MB
BOQ_1433672.xls
BOQ • 0.29 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].