REPAIR/ REPLACEMENT OF CERTAIN B/R WORKS, JOINERY, ALUMINIUM DOOR, WINDOW PARTITION, PLUMBING AND SANITARY FITTINGS, RAIN WATER PIPE, PVC WATER TANKS, ROOF TREATMENT, ROLLING SHUTTER ETC IN BLDG AT RESIDENTIAL AREA OF IRDE UNDER GE(I) R N D DEHRADUN

Amount

Taking down chowkats or frame of any description exc 1.5 Sqm each and n.exc 4Sqm with shutter(without taking off shutters from the frames) & remove off the premises complete all as specified and directed.

Taking down Shutters of any description exc 1 sqm but n. exc 2 sq. m each of any description complete all as specified and directed.

Taking down chowkats or frame of any description n.exc. 1.5 Sqm each complete all as specified and directed.

Taking down Shutters of any description n. exc 1 sq. m each of any description complete all as specified and directed.

S&F Pressed steel door frame for single door, size 105 x 60mm with one rebates incl necessary fixing lugs, hinges, lock strike plate, holdfast (size 25mm x 3 mm) of length 30 cm) etc., complete all as specified and as directed.

M & L PCC 1:2:4 type B0(12.5 mm graded) aggregate for filling in pressed steel door framed complete all as specified and directed.

S & F 35 mm thick second class hardwood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, moulded on solid (for each side): supplied and fitted to chowkat complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS sqare tube, complete all as specified and directed.

S&F factory made solid PVC moulded door shutters 28 to 30mm thick stiles), with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on back face, with wood free EPS, Supplying and fixing in frame at site as per specifiecation & drawing shown in section 8 of SSR part-II complete all as directed.

S & F 30 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauge etc with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Pt-1 section 8 and clause 8.24 (a) complete all as specified and directed.

S & F 35 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauge etc with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Pt-1 section 8 and clause 8.24 (a) complete all as specified and directed.

S&F 150 mm size aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 125 mm size aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F125mm size, butt hinges, heady weight, cold rolled mild steel complete all as specified and directed.

S&F100mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type complete all as specified and directed.

S&F 125mm size extruded aluminium alloy handles, fabricated type complete all as specified and directed.

M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specifed and directed.

S&F in repair vitreous china sqatting pan (orissa pattern) size 580mmx440mm, white with integral foot rest, any pattern including provision of cement concrete bedding (excluding fulshing cistern and flush pipe) with S or P trap, Fixed in repairs, complete all as specified and directed

S&F in repairs low level Flushing cistern 10 ltr capacity, PVC valveless syphonic action type, white with inlet, ball valve, float valve and handle , flush pipe, incl brackets and flushing pipe fixed in repairs complete all as specified and directed

S&F in repairs vitreous china,white, wash hand basin, flat back size 550x400mm 'including MS brackets including cutting for and pinning in, including waste pipe complete all as specified and directed

S & Fixed in repair Vitreous china, wash down water closet pan (pedestal pattern), white, including plastic water closet seat cover, closed pattern with flat bottom, connection to drain (or outgoing pipe) and to flushing pipe, antisiphonage pipe etc, complete.

S&F in repair 15mm size PVC connections internally threaded with PVC washer,PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 15 mm dia bib tap cast copper alloy (fency type), chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as directed.

Disconnecting & taking down existing water tank of capacity exc 250 liter and not exc. 500 liter and removing from site complte and S&F rotational moulded polyethylene water storage tanks 500 lts capacity (cylindrical vertical with closed top) hoisted with and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part I complete all as specified & directed.

Disconnecting & taking down existing water tank of capacity exc 500 liter and not exc. 1000 liter and removing from site complte and S&F rotational moulded polyethylene water storage tanks 1000 lts capacity (cylindrical vertical with closed top) hoisted with and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part I complete all as specified & directed.

S&F in repair Ball valves 15 mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms)

S&F in repair Ball valves 20 mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms)

S&F in repair 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

Disconnecting existing tanks (exc 250 but n. exc 500 ltrs capacity), setting aside (or lowering if required) for Cleaning and removing all scale and dirt, etc, from tanks. The complete tank be scrub to remove dirt, sediments, fungus & stains . The vacuumed tank is disinfected with anti-bacterial spray or liquid bleach. Tank is filled with water that is made to run through the taps to disinfect the water pipes , etc. and hoisting if required reconnecting and re-fixing in the same position. complete all as specified and directed.

Disconnecting existing tanks (exc 500 but n. exc 1000 ltrs capacity), setting aside (or lowering if required) for Cleaning and removing all scale and dirt, etc, from tanks. The complete tank be scrub to remove dirt, sediments, fungus & stains . The vacuumed tank is disinfected with anti-bacterial spray or liquid bleach. Tank is filled with water that is made to run through the taps to disinfect the water pipes , etc. and hoisting if required reconnecting and re-fixing in the same position. complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections,including cleaning for refixing or removal to store complete all as specified complete all as specified and directed.

S & F 15 mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

M&L for refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 15 mm dia pipes with and including all new fittings complete all as specified and directed. Note:- GI pipe shall be reused, received under Item No.36 here in above.

Taking up or down 20 mm steel tubing and connections,including cleaning for refixing or removal to store complete all as specified.

S & F 20 mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors.

Dismantling of cast iron, SGSW, PVC or reinforced concrete drain pipes in any size jointed in neat cement mortor and taking out of trenches or floor or wall if required

S&F PVC (SWR) pipe 75 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive fixed to wall with iron cleants etc complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive fixed to wall with iron cleants etc complete all as specified and directed.

S&F PVC (SWR) pipe 150 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F n repair PVC (SWR) bend/shoe 75 mm dia, any radius as required and jointed with approved adhesive and fixed to floor complete all as specified and directed.

S&F in repair PVC (SWR) Tee, Reducer/junction (single T) equal or unequal 75 mm dia, any radius as required and jointed with approved adhesive and fixed to floor complete all as specified and directed.

S&F n repair PVC (SWR) bend/shoe 110 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F n repair PVC (SWR) bend/shoe 150 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) floor trap , plain with grating including jointing with solvent cement .

Hacking out old broken glass (any thickness, size, quality or description) from metal frame incl punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane.

M&L for 4mm thick sheet figured glass, pin headed type and glazing with oil putty in square n exc 0.5 Sqm in each pane.

S&F in repairs Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples

M & L in fixed in repairs 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

Demolition of brick or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone works and precast concrete articles, complete all as specified and directed

M&L Brick work with sub class B bricks ,straight or curved on plan exc 6m mean radius built in CM 1:6 Complete all as Specified and directed

Taking down cement or cement lime plaster of any description including racking out joints, hacking for keys , scrubbing down with water etc, complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of concrete/brick interior surfaces in cement mortar 1:6 as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed.

M&L preparation of new surfaces pf plastered of walls and applying Two coat of distemper oil emulsion incl priming the surface and incl one coat of wall putty all as directed by Engr-in-Charge .

M&L for Rendering 5 mm thick on fair faces of concrete/brick interior ceiling surfaces in cement mortar 1:3 as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed.

M & L for preparing new suraces and applying two coat of white wash on walls .

M&L for Rendering 15 mm thick on fair faces of concrete/brick exterior surfaces in cement mortar 1:4 mixed with water proofing compound as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed.

M&L preparation of new plaster surfaces of walls, applying two coats of with Premium Acrylic Smooth exterior paint with Silicone additives of required shade @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) and incl 1 mm thick wall putty (Asian paint or Equivalent ) as per manufactor's instructions complete all as directed by Engr-in-Charge.(Note : painting will be done by brush/spray/roller of building upto the height G+6) all as per directed by Engr-in-Charge) .

M&L preparation of complete removal of existing treatment on surfaces of walls,surfaces should be free from any loose paint , dust or grease, growths of fungus, algae or moss should be removed by wire brushing and water . Cracks should be filled with crack seal of premium quality , dents and holes should be filled with putty or a mix of white cement and fine sand in the ratio 1:3 and applying two coats of with Premium Acrylic Smooth exterior paint with Silicone additives of required shade @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) and incl one coat thick wall putty (Asian paint or Equivalent ) as per manufactor's instructions complete all as directed by Engr-in-Charge.(Note : painting will be done by brush/spray/roller of building upto the height G+6) all as per directed by Engr-in-Charge) .

Demolition of cement concrete (unreinforced) of any description as in ground floors and pavings not exceeding 15cm thickness (above or below ground floors) complete all as specified and directed

M & L for providing plain cement concrete, type E-2, 1:5:10 (using 40 mm graded brick aggregate) as in sunken, filling and mass concrete complete all as specified and directed.

M&L 25mm PCC 1:2:4 Type B-0 (Using 12:5mm stone agg) as in base floor , complete all as directed and specified .

M&L for waterproffing treatment to sunkin portion of WC, bathroom etc by applying :- (a) All the borehole gaps between concrete surface and pvc pipe of various dia upto the neck level shall be filled with non-shrink free flow grout - SmartCare GP Grout or approved equivalent having dual shrinkage compensation property. Before the bore packing, surface of the pvc pipe and concrete surface will be made rough and sand will be sprinkled with polymer bonding agent . (b) Applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, SmartCare Ultra Block 2K or approved equivalent . The mixing ratio of the coating shall be 60:40 (Powder : Liquid) parts by weight without any water addition in the mixing, etc., complete as per manufacturers specifications. (c) Loosely lay 150 GSM Geotextile (non-woven polyester) with a min of 100mm wide overlap . (d) Laying slope making and protection to the waterproofing treatment with 30 mm avg. thick M20 grade screed for floors. Providing and applying 15 mm thick with CM 1:4 for wall plastering admixed with PC based integral waterproofing compound SmartCare Vitalia, etc. complete, as per manufacturer's specifications

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with all plugs, washers, fittings and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specifed and directed.

M&L for taking down/dismantling of existing roof treatment of any description such as PCC Padding/ Coba treatment/ mud phuska/Lime conc, Old APP membrance roof treatment etc terracing including screed bed etc. Hessian base felt/tar felt etc. (any type and thickness)complete all as specified & directed.

M&L for Removal of demolished materials to a distance exceeding 250 Mtr but not exceeding 500 Mtr and deposting where directed at a level n.exc 1.5 m above the starting point, complete all as specified and directed .

M&L for Waterproofing on roof/parapet for cleaning and surface preparation and making surface dust free . Crack more than 0.5 mm then opening of crack in V grove and filling with epoxy mortor and 01 coat of epoxy primer (Resin + Harder) and 02 coat of ultron hybrid polyurea (cunsumption 01 kg per 01 sqm) complete all as specifed and directed by Engr-in-Charge. Note :- The work of water proofing treatment shall be got executed throughh expert team of manufacturers or authorised applicator of manufacturer.. Mke - Asian Paints/PIDILITE/STP/FOSROC/ACC/L&T/MARUTI

S&F in repairs kitchen plate rack with and including shelves and hanging arrangement for utensil for kitchen , made of stainless steel sheet 0.63 mm thick size 24"x24"x10" complete as as specifed and directed.

Taking down old curtain rods/ drapery rods of any description and S&F drapery rod 32 mm dia, high Strength aluminium rod with powder coated paint of thickness 40/60 microne of wood finish with minimum 8 rings in each metre length of rod of ABS Plastic in matching colour & installations brackets of galvanised steel, powder coated paint in matching colour with all accessories complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description in any position not otherwise specifically provided for and removing demolished materials to a distance exceeding 250 Mtr complete all as specified and directed.

M & L RCC type B-01:2:4 (12.5mm graded stone aggt) for slabs supports on walls complete all as specified and directed.

M&L for use and waste form work to soffits of suspended slabs such as roof slabs , floor slabs, landings and similar work for fair finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

S&F in repairs 18 mm thick factory made PVC sheet one side pre-laminated sheet ktichen cabinet shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for marking edge lipping bending for 0.5 mm thick PVC sheet lipping at all four edges using bonding tape etc complete all as per specified and directed by Engr-in-Charge manufactures specification .

S & F in repairs factory made PVC shelf/partition of required size consisting of panel of 18 mm thick required size consisting of panel of 18 mm thick celuka PVC ply and for supporting the hold of shelf /partition and shall provided 3 edges in size 18mm x 18 mm as per required lenght the front side of the edge visible in the front of the shelf/partition to be edge lipped by 18mm widht x 1 mm thick PVC sheet of density 600 kg/cum manufactured by ISO 9001-2015 Certified Company , using solvent cement etc. complete all as specified and directed.

S&F stainless steel shelf closing hinges 75 mm size for PVC door shutters complete all as specified and directed

S&F 50 x 15 mm size magnet door catcher for closing for PVC door shutter complete all as specifid and directed .

S& F 100 mm size MS mat/glossy finish handle complete all as specfied and directed .

S&F Brass handles 100mm size, cast type, polished bright as approved by Engr in Charge complete all as specified and directed

S&F in repair 40 mm dia, brass, knobs for cupboard fixed with nut, screw and washer of mild steel, bright finised complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm complete all as specified and directed.

S & Fixed in repair Vitreous china, wash down water closet pan (pedestal pattern), white, including plastic water closet seat cover, closed pattern with flat bottom, connection to drain (or outgoing pipe) and to flushing pipe, antisiphonage pipe etc, complete.

S&F in repair vitreous china sqatting pan (orissa pattern) size 580mmx440mm, white with integral foot rest, any pattern including provision of cement concrete bedding (excluding fulshing cistern and flush pipe) with S or P trap, Fixed in repairs, complete all as specified and directed

S&F in repairs low level Flushing cistern 10 ltr capacity, PVC valveless syphonic action type, white with inlet, ball valve, float valve and handle , flush pipe, incl brackets and flushing pipe fixed in repairs complete all as specified and directed

S&F in repairs vitreous china,white, wash hand basin, flat back size 550x400mm including one number chromium plated waste fittings, 32 mm dia , brass withlong screwed shanks and flg nut, flange and fixed with and including 32 mm dia PVC waste pipe with connector MS brackets, 2 Number including casting for and pinning in end of brackets complete all as specified and directed

Demolition of stone slab and tiles laid bedded and pointed in any mortor of any description or thickness in floor complete all as specifed

M&L coloured Precast Cement concrete heavy duty deisigner tiles of size 400X400X30 mm set , jointed and pointed in neat cement slurry in floors with grey cement and pigment over and including 15 mm thick screed bed in CM 1: 6 complete all as specified and directed. Make NTC Chandigarh

M & L coloured Rubber Moulded Chequred Cement Concrete tiles 300 x 300 x 25mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigment over and including 15 mm thick screed bed in CM 1:6

M & L coloured Rubber Moulded Chequred Cement Concrete tiles 250 x 250 x 25mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigment over and including 15 mm thick screed bed in CM 1:6

M&L for post construction ATT along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre incl drilling and plugging holes etc in apron complete

M & L for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors

M&L post construction ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.50 litres/hole by driling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete

M&L for Running welding in repairs Thickness of metal to be welded n exc 6mm coplete .

Removal of demolished materials to a distance out side defence land at contractor own arrangement complete all as specified and directed .

M&L for greasing and oiling in old rolling shutters (area exceeding 10.00 sqm of each shutter) of each parts i.e guide channels, cranks, springs, gearboxt and locking arrangement etc. with and including repairs as required for smooth functining of rolling shutter complite all as specified and directed.

M&L for greasing and oiling in old rolling shutters (area not exceeding 10.00 sqm of each shutter) of each parts i.e guide channels, cranks, springs, gearboxt and locking arrangement etc. with and including repairs as required for smooth functining of rolling shutter complite all as specified and directed.

Taking down carefully unservicable ball bearing from rolling shutters and S&F ball bearing heavy duty as required size at approprite place, match the existing of gear operated type rolling shutter complite all as specified and directed.

Taking down carefully unservicable spring from rolling shutters and S&F new spring heavy duty as required size at approprite place, match the existing of gear operated type rolling shutter complite all as specified and directed.

Taking down carefully unservicable safty lever mild steel lock any type from rolling shutters and S&F new safty lever mild steel lock 4 lever heavy duty as required size at approprite place, match the existing of gear operated type rolling shutter complite all as specified and directed.

S&F in repair steel rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp & staple & one shop coat of primer; erected in position as indicated, complete; push pull or manual type Thickness of laths 1.00 mm complete all as specified and directed

S&F in repair steel rolling shutters, gear operated type with bevel gear box and crank handle, ball bearing, as specified including top cover, anchoring rod, hasp & staple & one shop coat of primer; erected in position as indicated, complete; push pull or manual type Thickness of laths 1.00 mm complete all as specified and directed

M/S P K ARORA