CIVIL WORK

Amount

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :

25 mm dia (heavy type)

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing PTMT door catcher of length 72 mm and dia. of 42 mm with suitable washers weighing not less than 33 gms

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws:

30 mm thick shutters.

With ISI marked stainless steel butt hinges of required size - Kiln seasoned and chemically treated hollock wood.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the ost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase

20 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

1:6 (1 cement: 6 fine sand)

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) including scaffolding wherever required etc. all complete as per direction of engineer-in- charge:

Flush/ Ruled pointing

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including pplying additional coats wherever required, to achieve even shade and colour.

Old work (One or more coats)

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and anufacture, including applying additional coats wherever required to achieve even shade and colour.

One coat

Two coats

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting (one or more coats) on rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour on old work :

100 mm diameter pipes .

150 mm diameter pipes .

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work

Finishing walls with water proofing cement paint of required shade :

Old work (one or more coats @ 2.20 kg/10 sqm) complete.

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead :

With cement mortar 1:4 (1cement: 4 coarse sand).

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:

Float glass panes of thickness 3.70 mm.

Renewing glass panes, with wooden fillets wherever necessary:

Float glass panes of nominal thickness 3.70 mm.

Providing & fixing White vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.

Orissa pattern W.C Pan of size 580x440 mm

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved unicipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall

20 mm nominal outer dia. Pipes.

25 mm nominal outer dia .Pipes.

Providing and fixing brass bib cock of approved quality :

15 mm nominal bore

Providing and fixing brass stop cock of approved quality :

15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

20 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 :

15mm nominal bore

Providing and fixing PTMT bib cock of approved quality and colour.

15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT stop cock of approved quality and colour.

15 mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.

15 mm nominal bore, 105 mm long. Weighing not less than 138 gms.

Providing services of Plumber for plumbing, sanitary installations, water supply fittings and related works complete in a working day i/c cost of all T&P.

Providing carpenter as and when required for attending need basis complaints of carpentry works such as repair of doors , windows , cupboard shutters as per requriment on need basis for all jobs in one working day i/c cost of screws ,nails, fevicol clamps etc. (The material required for attending the complaints shall be arranged by the contractor at site and will be paid in separate items except cost of all T&P for attending the work shall be arranged by the contractor and nothing extra shall be paid.

Providing services of Beldar /Helper for need basis for carpenter / plumber as and when required cleaning of whole Type V/2 Campus and cutting of branches of trees hanging on terrace etc. all complete as per direction of engineer-in-charge including the cost of ledder, tagari, phawra etc.for all jobs in one working day and disposal of all unused/ unserviceable materials from the outside of campus of any lead.

Providing / supplying and fixing panelling to doors & windows with nail, screws, adhessive etc where ever required but excluding labour cost.

12 mm thick BWP commercial ply on both faces.

6 mm thick BWP commercial ply on both faces.

Supplying of M.S. Wire gauge of 0.56 mm dia for renewing of wire gauge of doors & windows including new wooden beading of required size if required as per site condition

Providing services of sewerman as and when required on need basis for cleaning of manholes and sewer lin of both Type V/1-2 quarters upto septic tank etc. all complete as per direction of engineer in charge.

Providing / supplying and fixing wooden boards in shelves, counters, drawers, wall panelling etc with nail, screws, adhessive, lipping as directedby Engineer in charge etc where ever required but excluding labour cost.

18 mm thick block board (BWP type ISI marked) including lipping and beading on exposed face.