GENERAL

Supplying of hot applied thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250gms with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqm area, thickness of 2.5mm exclusive of surface applied glass bead as per IRC: 35, the material should be of Berger / Asian Paints/ Prime Roads/ Equivalent brand and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carry out random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserves the right to cancel or reject the total supplied consignment of the said material and will compel the vendor to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45°C as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-1, 1989 and should pass at the range of '0'°C to '-10'°C. d) Adhesion: Strong. e) Softening point: 102°C. f) Dried film finish: Smooth and uniform. g) Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-1997.

Supplying & Fixing of Molded Shanks Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 - DO III Dt 11.06.1997. The height, width and length shall not exceed 50 mm, 100 mm and 100 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks (of diameter not less than 19 +/- 2 mm and height not less than 30 +/- 2 mm) from the body is to be a minimum value of 700 Kgs. Fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by the Engineer-in-Charge.

Supplying & Fixing of Molded Shanks SOLAR Raised Pavement Markers (3M / DARK EYE/ Equivalent brand) made of polycarbonate conforming to standard size 125mm × 125mm × 25mm and 65mm shank height includes clear facings reflectors designed for maintenance free operation with Flash rate 1-2Hz, Aluminum-alloy shell, Ingress Protection confirms to IP67, High efficiency Monocrystalline Solar panel 3V / 130mA allowing charging at low solar radiation, Low self Discharge (LSD) 1.2V/1.3AH Ni-mh rechargeable battery, Automatic ON/OFF Dusk to Dawn operation, Six high luminance LEDs, Wavelength 630mm with 14,000mcd, Red(Standard), Amber, Blue, Green and white LED colors, Visibility 800 meters, Good even during hazy weather, compressive strength confirming to ASTM D 4280-15. Fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by the Engineer-in-Charge.

Provision for Seignorage charges

Provision Towards merit 2%

Provision Towards DMF 30%

Provision for NAC @ 0.10%

Provision for GST @ 18%

Provision for TPQA @ 0.739 %

Unforeseen item