CNT/WSS/MWB/3529/2022-23

Amount

Bill No.1. Operation and maintenance of Manali booster by providing required qualified and experienced engineers, skilled and unskilled personal to carryout all the mandatory duties listed and as per the maintenance schedule enclosed. including ESI & EPF as per the norms and all insurance for the manpower and for machinery along with uniform, Identity card, safety equipments, tools, grease, oil, cotton waste, gland packing rope, house keeping and garden maintenance etc complete for 5 years quantity.

For First Year

For Second Year

For Third Year

For Fourth Year

For Fifth Year

Bill No.2. Supply, delivery and replacement of spares for all motor & pumpset equipments and other accessories in Manali booster for 5 years

HT Two pole structure

Replacement of dropout fuses

120-185 sqmm 3 core HT cable outdoor terminations XLPE 11KV (E) - EPKT 3362

Replacement of lighting arrester

Replacement of pin insulator

Replacement of Horn gap unit

Painting of two pole structure

Replacement of aluminium bus bar

Replacement of knife of AB switch

HT end termination including compound

Servicing of AB switch

250 KVA Transformer

Transformer oil filteration

Replacement of tap changing mechanisum

Replacement of air breather and silica gel

Replacement of dial thermo meter

Replacing of terminal bush (HT)

Spray painting to the transformer

Transformer oil

Transformer winding including transportation charges

Transformer yard earthing using copper flat and TWIN earthing as per IS

400A Oil Circuit Breaker

Replacement of fixed and moving contacts

Replacement of operating mechanisum set

Replacement of triping mechanisum set

Replacement of no volt coil

Replacement of hylem plate

Replacement of dash pot oil

Replacement of moving contacts for drawout OCB

Replacement of fixed contacts for drawout OCB

Replacement of transformer oil

Dismantling, assembling and testing at site

75 HP Induction Motor

Rewinding of stator (1450 RPM)

Rewinding of Rotor (1450 RPM)

Improving the insulation value by varnishing and heating for motor

Replacement of bearings

Replacement of bearing end covers

Replacement of terminal plate

Replacement fan / fan blade

Termination of cable from motor insulation wire

Reconditioning of motor shaft true to axis

Reconditioning of motor shaft by metalising and turning

Reconditioning of bearing end covers by metalising and providing sleeve

Dismantling, refixing, painting, aligning and testing on load

Transport charges

75 HP Centrifugal pump

Replacement of SS shaft.

Reconditioning of shaft by metalising true to axis

Replacement of shaft sleeve in SS.

Providing new key ways, key.

Replacement of coupling tyre/star coupling bush.

Replacement of coupling pulley.

Replacement of coupling bolts, nuts and rubber bushes

Reconditioning of impeller by metalising, turning & dy.bl..

Providing impeller nut

Providing new taps and new studs

Replacement of studs.

Replacement of pump gland in MS .

Replacement of ball/Roller bearing SKF/Eq.make.

Providing dummy plate with rubber insertion and bolt and nuts.

Dismantling, refixing, alinging, testing & commssioning.

Reconditioning of pump shell by metalising and turning

Providing new tape for priming line and with gate valve(1" valve)

Reconditioning of base plate, providing base bolts including welding and civil work

Replacement of base plate, providing base bolts

Providing engine oil and greese

Replacement oil seal

Reconditioning of bearing housing

Transport charges

75 HP Auto Transformer Starter

Replacement of fuse unit - HRC

Replacement of fuse links

Replacement of pilot lamp indicator with holder

Replacement of push button with kit

Replacement of volt meter

Replacement of Ammeter

Replacement of hour meter

Replacement of single pole two way switch

Replacement of contactors

Replacement of over load relay

Replacement of timer electronic

Replacement of no volt coil

Replacement of current transformer

Rewiring the power and control cable

Replacement of single phase preventor and phase preventor

Rewinding the auto transformer coil

Replacement of transformer oil

30 HP Induction Motor

De-coupling the motor from its pump, dismantling, transporting charges from site to workshop

Rewinding of stator coil with high class insulation enamel coper wire and necessary insulation paper with sleeve varnished etc complete

Rewinding of Rotor (1450 RPM)

Improving the insulation value by varnishing and heating

Replacement of bearings

Replacement of bearing end covers

Replacement of terminal plate

Replacement fan / fan blade

Termination of cable from motor insulation wire

Reconditioning of motor shaft true to axis

Reconditioning of motor shaft by metalising and turning

Reconditioning of bearing end covers by metalising and providing sleeve

Dismantling, refixing, painting, aligning and testing on load

Transport charges

30 HP Centrifugal pump

Dismantling the pump from bed and transportation the pump from site to workshop

Reconditioning of pump shaft and impeller by metalising, turning, facing etc complete

Replacement of ball bearings with suitable make SKF

Replacement of pump G.M. bush

Reconditioning of bearing housing for both sides

Replacement of pump gland bush with suitable studs and nuts etc complete

Providing coupling pulley with flexible fenner make coupling tyre including bolts and nuts etc complete.

Providing G.M guide ring for pump impeller

Reassembling, aligning with motor testing on load at site including painting, transporting charges etc complete.

Replacement of shaft

Replacement of studs.

Providing dummy plate with rubber insertion and bolt and nuts.

Providing new tape for priming line and with gate valve(1" valve)

Reconditioning of base plate, providing base bolts including welding and civil work

Replacement of base plate, providing base bolts

Replacement oil seal

30 HP Automatic Star & Delta Starter

Replacement of fuse unit - HRC

Replacement of fuse links

Replacement of pilot lamp indicator with holder

Replacement of push button with kit

Replacement of volt meter

Replacement of Ammeter

Replacement of hour meter

Replacement of single pole two way switch

Replacement of contactors

Replacement of over load relay

Replacement of timer electronic

Replacement of no volt coil

Replacement of current transformer

Rewiring the power and control cable

Replacement of single phase preventor and phase preventor

30 HP VFD starter

Replacement of 63A fuse unit with fuse link (TWAD SOR P.NO 179 SL.NO 4.a, 22-23)

Replacement of 10A single pole MCB (TWAD SOR P.NO 190 SL.NO 6.a, 21-22)

Replacement of 6A double pole MCB (TWAD SOR P.NO 190 SL.NO 6.e, 21-22)

Replacement of 6A single pole MCB (TWAD SOR P.NO 190 SL.NO 6.a, 21-22)

Replacement of pilot lamp indicator lamp

Replacement of push button with kit

Replacement of 9A power contactor

Replacement of CT disconnector terminal block

Replacement of 6" cooling fan

Replacement of 6" air filter

Replacement of rated insulatd voltage of 1100V AC + /-10Y variation

Replacement of rated frequency drive 50HZ

Replacement of IP 42 degree of production

Rewiring of 1.5sqmm control wiring as per specification required

End termination suitable for existing 30HP centrifugal pumpset etc complete

320 KVA DG Set

Rewinding of alternator stator

Rewinding of alternator rotor

Improving the IR value by varnishing and heating eyc complete

Replaement of terminal plate

Replacement of terminal studs and lugs

Replacement of carbon brushes

Replacement of brush holder

Replacement of AVR

Dismantling, refixing, painting, transporting, aligning and testing etc

Replacement of bearings

Replacement of rectifier unit

Replacement of commutator assembly

Replacement of radiator

Repairs to radiator by welding and providing metal paste etc

Replacement of fan belt

Replacement of fuel circulator hose

Replacement of water circulation hose with clamp

Replacement of air filter

Replacement of oil filter

Servicing of the self motor

Repairs to self motor control circuit wire

Replacement of engine oil

Replacement of nozzle

Replacement of speedo meter cable

Replacement of oil cooler

Servicing of turbo charger

Service of engine with gasket

Replacement of fuel filter

Replacement of silencer pipe

Replacement of aspestos rope

Replacement of muffler

Calibration of fuel pump

Replacement of battery with terminals and cables

Replacement of pressure cage

Replacement of coupling unit

Replacement of coupling guard

Replacement of anti vibration mounting pad

Servicing of battery

Replacement of MCB control

Replacement of frequency meter

Replacement of energy meter

Replacement of hour meter

Replacement of change over switch

Rewiring of control panel

Cable

Supplying of 240-300 sqmm 3.5 core LTUG cable straight through jointing kit including labour cost and jointing materials etc complete.

"Supply and laying of 3.5 core 240 sqmm LTUG cable in a trench to be excavated at the depth of 2.5"" putting 6"" layer sand and conveying the cable with brick and sand refilling te earth to make good.

Supplying and clamping of 3.5 core 95 sqmm PVC LTUG cable by MS clamps on wall for 75HP induction motor.

Supplying and clamping of 3.5 core 50 sqmm PVC LTUG cable by MS clamps on wall for 30HP induction motor.

Supplying and fixing of cable gland and termination with aluminium cable by 3 1/2 core 240 sq.mm PVC UG cable and with earth connection.

Supplying and fixing of cable gland and termination with aluminium cable by 3 1/2 core 95 sq.mm PVC UG cable and with earth connection.

Supplying and fixing of cable gland and termination with aluminium cable by 3 1/2 core 50sq.mm PVC UG cable and with earth connection.

Capacitor Bank for 120 KVAR

Replacement of 32A contactor

Replacement of 25 KVAR capacitor

Replacement of 20 KVAR capacitor

Replacement of 15 KVAR capacitor

Replacement of 10 KVAR capacitor

Replacement of 5 KVAR capacitor

Replacement of pilot lamp indicator

Replacement of push button with kit

Rewiring the power and control cable

Lighting

Replacement of 80 watts LED Street Light Fitting (SOR P,No 164, SL.No 40.iii 2022-23)

Replacement of 20W 4 Feet LED fitting with LED (SOR P,No 164 SL.No 38.2 2022-23)

Replacement of 20 Amps MCB DP (TWAD P,No 191, SL.No 8.c 2021-22)

Replacement of 6 Amps MCB (TWAD P,No 190, SL.No 6.a 2021-22)

Replacement of 40 Amps 4 pole MCB

UGT Cleaning

Hire charges for Diesel Pump set for 15 HP

Removing sludge from UGT and other sewage handling structure and disposing it with an initial lead of 10m and initial life of 2M

Incoming 400A MCC Panel Board

Replacement Three phase Digital Voltmeter

Replacement Three phase Digital Ammeter

Replacement of 200A MCCB (4 pole)

Replacement of 400A MCCB (4 pole)

Replacement of 630A change over switch

150mm Sluice valve

Replacement of spindle rod SS

Replacement of spindle rod nut

Rethreading, mechining the existing shaft

Replacement of bolts and nuts MS with rubber

Dismantling and refixing etc

Replacement of gland with studs

Replacement of sluice valve labour

Reconditioning of disk with lining

Replacement of brackets

Provision of operating key rod

300mm Sluice valve

Replacement of spindle rod SS

Replacement of spindle rod nut

Rethreading, mechining the existing shaft

Replacement of bolts and nuts MS with rubber

Dismantling and refixing etc

Replacement of gland with studs

Replacement of sluice valve labour

Reconditioning of disk with lining

Replacement of brackets

Provision of operating key rod

350mm Sluice valve

Replacement of spindle rod SS

Replacement of spindle rod nut

Rethreading, mechining the existing shaft

Replacement of bolts and nuts MS with rubber

Dismantling and refixing etc

Replacement of gland with studs

Replacement of sluice valve labour

Reconditioning of disk with lining

Replacement of brackets

Provision of operating key rod

Reconstruction of Valve Chambers

Diesel pumpset for dewatering

Hire charges for Diesel Pump set for 10 HP .

Replacement of specials & pipes

150mm dia Sluice Valve

300mm dia Sluice Valve

350mm dia Sluice Valve

450mm dia Sluice Valve

150mm dia DI D/F pipe 1 m long.

150mm dia DI D/F pipe 5.5 m long.

200mm dia DI D/F pipe 2 m long.

300mm dia DI D/F pipe 1 m long.

300mm dia DI D/F pipe 2 m long.

300 x 200 mm dia DI D/F Reducer

200 x 150 mm dia DI D/F Reducer

200mm dia DI 900 D/F bend

300mm dia DI 900 D/F bend

Attending leaks in pipes and specials including earth work excavation cost of jointing materials and labour charges etc.inside the pump house

Bill No.3. White washing/Colour washing of civil structures, painting of iron structures two times in 5 Years

Bill No.3.1 White washing/Colour washing of civil structures & painting of iron structures 1st term in 5 Years

Painting with two coats of ready mixed plastic emulsion paint first class quality and of approved colour over a priming coat including thorough scrapping clean removal of dirt etc, complete and including necessary plaster of paris, putty, etc wherever required in pump house, Office room, DG Room

White washing two coat (old work) in pump house ceiling, Office room, DG Room ceiling & sump top

Painting with superior quality ready mixed paint of chocolate, light green, grey or any other approved colour for Old iron work two coats.

Bill No.3.2. White washing/Colour washing of civil structures & painting of iron structures 2nd term in 5 Years

Painting with two coats of ready mixed plastic emulsion paint first class quality and of approved colour over a priming coat including thorough scrapping clean removal of dirt etc, complete and including necessary plaster of paris, putty, etc wherever required in pump house, Office room, DG Room

White washing two coat (old work) in pump house ceiling, Office room, DG Room ceiling & sump top

Painting with superior quality ready mixed paint of chocolate, light green, grey or any other approved colour for Old iron work two coats.

Thirumalai Enterprises

M V POWER CONSULTANTS AND ENGINEERS PVT LTD

SATTVA ENGINEERING CONSTRUCTION P. LTD

E.SARAVANAN

Hydro Electrical Systems

Sri Selvaganapathy Engineers