GENERAL Govt Secretariat Renovation of office room of Chief minister Renovation of office room of Chief minister 2023 24 General Civil Work 2 work1 2026

15.39.2:Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking with in 50 metres lead:Thickness above 10mm upto 25 mm

15.23.1:Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

15.57:Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge

OD123321/2026-2027:Supplying and fixing Welspun Nylon Carpet Tile of size 50 cm x 50 cm , manufactured using 100% Solution Dyed Nylon-NY6+, having a gauge of 1/12 Loop Infinity, tufted weight of 20?24 oz/sq.yd, density 5000+, pile height 4?5 mm, total thickness 6?7 mm, and backed with Welspun Ecolite PVC backing, laid over the existing floor surface using approved adhesive, including surface preparation, trimming, jointing, alignment to correct lines, patterns, and levels, handling, site cleanup, and disposal of waste/scrap material complete as per the direction of the Engineer-in-Charge.

12.45.3:Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

21.1.1.1:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

OD123325/2026-2027:Plywood paneling (12 mm): Providing and fixing paneling using plywood, 12 mm thick plywood ( BWP 710 Grade ) to be fixed onto the existing framework/wall using drywall screws and adhesive. Complete as per the direction of the Engineer- in- Charge including all costs of accessories, labour charges etc. complete

OD123322/2026-2027:Plywood paneling (18 mm): Providing and fixing paneling using plywood, 18 mm thick plywood ( BWP 710 Grade ) to be fixed onto the existing framework using drywall screws and adhesive including primer. Complete as per the direction of the Engineer- in- Charge including all costs of accessories, labour charges etc. complete

OD123316/2026-2027:Mica panelling : providing and fixing mica 1mm thick on to the existing plywood (superior quality) using adhesive complete as perthe direction engineer in charge including all the cost of accessories, labour charges etc. complete(data based on 9.126.1 of DAR)