Tvm Corporation-Implementing Health and Wellness centre(Rent) In Powdikonam Ward-Scheme-6-Pro No - 2248/25

Amount

Wellness centre

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.1:Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

OD68901/2025-2026:Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete: 20 mm dia Modified data 9.46.2

17.7.7:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap

17.10.2.3:Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board470x420 mm bowl depth 178 mm

OD17675/2025-2026:15mm CP Short body tap

17.18.1:Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete.10 litre capacity - White

17.20.1:Providing and fixing solid plastic Seat with lid for pedestal type W.C. pan complete:White solid plastic seat with lid

OD68909/2025-2026:Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. Modified DSR 14.43

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

OD68925/2025-2026:Finish walls with Acryllic Smooth exterior paint of required shade: Old work ( Two or more coats applied @ 1.67 ltr/10 sqm) on existing cement paint surface. (Modified DSR 14.66.1)

OD68915/2025-2026:Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade: One or more coats on old work (Modified DSR 14.54.1)

10.25.1:Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads,landings etc. of stair cases, including use of chequered plate wherever required, all complete

10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

OD17679/2025-2026:Supplying, Fitting in of Venyl sticker for name board with all costs etc a per the instructions from Engineer in charge . ( Payment as per actual bill )

OD18623/2025-2026:Providing and fixing PVC foam board exterior grade(Grade-I) to backing or studding with screws etc. complete (Frames,backing or studding to be paid separately) Pre-laminated with decorative lamination on both side exterior Grade-I PVC foam board 18mm thick.

OD18624/2025-2026:Supplying and fixing Auto close Hinges including all complete as per direction of Engineer-in-charge

OD18625/2025-2026:Supplying and fixing Godreg Mulb lock including all complete as per direction of Engineer-in-charge

OD18626/2025-2026:Supplying and fixing 18 inch Drawer Slider including all complete as per direction of Engineer-in-charge

OD18627/2025-2026:Providing and fixing aluminium C shape handle of 90 mm with SS screws etc. complete as per direction of Engineer-in-Charge

OD18628/2025-2026:Suppying and fixing RA connector 25x35mm including all complete as per direction of engineer-in-charge

13.71:Lettering with black Japan pint of approved brand and manufacture

OD19341/2025-2026:Engaging carpenter for repairing work

OD19342/2025-2026:Labour Engaging for miscellaneous works -mancooli/Unskilled labour etc complete

OD33217/2025-2026:Drawing cartoon pictures on wall using specified materials including cost of materials

VISHNU J R (BID ID -2262673)

PRADEEP.T (BID ID -2263107)

Bidder Name

Vanajan

VISHNU J R

PRADEEP.T