Construction of PHC building Level-II with residence at Kalhani Tehsil Thunag Distt Mandi SH C/o building portion WS and SI Septic tank soak pit site development and rain water harvesting system

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m (one point five metre) in width or 10 sqm (ten square metre) on plan, including dressing of sides and ramming of bottoms, lift upto 1.5 m (one point five metre) , including getting out the excavated soil and disposal of surplus excavated soils as directed, within any lead. Ordinary rock including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm (thirty centimetre) in depth, 1.5 m (one point five metre) in width as well as 10 sqm (ten squaremetre) on plan including getting out and disposal of excavated earth upto any lead , as directed by Engineer-in-charge Ordinary rock including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m (one point five metre) , including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm (twenty centimetre) in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m (fifty metre) All kinds of soil Pipes, cables etc, not exceeding 80 mm (eighty millimetre) dia including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm(fourty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm(fourty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying cement concrete in 1:5:10 (1 cement : 5 coarse sand) : 10 graded stone aggregate 40 mm(fourty millimetre) nominal size retaining walls, return walls, walls (anythickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying upto floor all level in position cement concrete 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm (twenty millimetre) nominal size) to give a smooth and even surface including centering and shuttering etc. but excluding cost of reinforcement in String course, copings, bed plates, anchor block, plain windows sills and the like including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand) : 4 graded stone aggregate 40 mm (fourty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying damp-proof course 40mm (fourty millimetre) thick with cement concrete 1:2:4 (1 cement : 2 coarse sand): 4 graded stone aggregate 12.5mm (twelve point five millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg/sqm (one point seven kilogram per square metre) on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Making plinth protection 50mm (fifty millimetre) thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm (twenty millimetre) nominal size over 75mm(seventy five millimetre) thick bed of dry brick ballast 40 mm (fourty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm (fifteen into twenty centimetre) in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm (fourty millimetre) nominal size and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm (twenty millimetre) nominal size and finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Centering and shuttering including strutting, propping etc. and removal of form for including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . Foundations, footings, bases of columns, sqm etc. for mass concrete

Suspended floors, roofs, landings, balconies and acceess platform

Lintels, beams, plinth beams, girders, sqm bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral- staircases

Edges of slabs and breaks in floors and walls : Under 20 cm wide

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (1 cement : 3 coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . (I) All works upto plnth level. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . II ) All works above plinth level upto Floor -V level. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in foundations and plinth in : Cement mortar 1:3 (1 cement : 3 coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm (twenty millimetre) nominal size at plinth level. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Coursed rubble masonry (second sort) with hard stone in foundation & plinth with : Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Coursed rubble masonry with hard stone (first or second sort) in superstructure above plinth level and upto floor five level.nMasonry work (second sort), in cement mortar 1:6 (1 cement: 6 coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing weep holes with 110mm (one hundred ten millimetre) dia pvc pipes laid in slope of 1:20 including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Boulder filling under floors tightly hand packed including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 18 mm (eighteen millimetre) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (twenty millimetre) thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade : Area of slab over 0.50 sqm (zero point five zero square metre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing edge moulding to 18 mm(eighteen millimetre) thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer- ncharge. (Note:- Butt hinges and necessary screws shall be paid separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm (twenty five millimetre to fourty millimetre) thick :Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm (twenty five millimetre to fourty millimetre) thick : 4 mm (four millimetre) thick glass pane (weight not less than 10 kg per sqm (ten kilogram per squaremetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm (four millimetre) thick float glass panes, including ISI marked M.S. pressed butt hinge bright finished of required size with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (one point four millimetre) in both directions with wire of dia 0.63 mm (zero point sixty three millimetre) , for doors, windows and clerestory windows with hinges and necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 18 mm (eighteen millimetre) thick, 150 mm (one point fifty millimetre) wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm (six millimetre) coir veneer board, nickle plated M.S. Pipe 20 mm (twenty millimetre) dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm (twenty five into three millimetre) M.S. Flat 10 cm (ten centimetre) long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm (hundred millimetre into fourty millimetre into fourty millimetre) on both inner side of pelmet and rawl plugs 75 mm long etc. all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing 40x5 mm (fourty into five milimetre) flat iron hold fast 40 cm( fourty centimetre) long including fixing to frame with 10 mm (ten millimetre) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre) 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . (i) 300x16 mm (three hundred into sixteen millimetre)

(ii) 250x16 mm (two hundred fifty into sixteen millimetre)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . (i) 250x10 mm (two hundred fifty into ten millimetre)

(ii) 200x10 mm (two hundred into ten millimetre)

(iii) 100X10 mm (one hundred into ten millimetre)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . ( I )125mm (one hundred twenty five millimetre)

( I ) 100mm (one hundred millimetre)

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc.complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 19 mm (nineteen millimetre) thick water proof termite resistant commercial board box including shelves and shutters, the back side cup board / cabinet shall be 8 mm (eight millimetre) thick ply and all the cut portions of shelves shall be finished with 6 mm (six millimetre) thick hard wood edging. The cut portion of shutters from all sides shall also be finished with 12 mm (twelve millimetre) thick hard wood edging. The shutter from out side shall be finished with 4 mm (four millimetre) thick vaneer Ply of approved shade to match with panelling including stainless steel hinges hinges and magnetic catcher with in all accessories etc. complete as per detailed drawing including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, kg railings, brackets, gates and similar works including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm (thirty five into thirty five into five millimetre), joints mitred and welded by angle iron 35x35x5 mm (thirty five into thirty five into five millimetre)or 35x 5 mm (thirty five into five millimetre)flat pieces to the existing Tiron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Precast terrazo tiles 22 mm (twenty two millimetre) thick with graded marble chips of size upto 12 mm (twelve millimetre), laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm (twenty millimetre) thick bed of cement mortar 1:4 (1 cement:4 coarse sand) : Light shade pigment with white cement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Precast terrazo tiles 22 mm (twenty two millimetre) thick with graded marble chips of size upto 12 mm (twelve millimetre) , laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm (twenty millimetre) thick bed of cement mortar 1:4 (1 cement:4 coarse sand) : Medium shade pigment with 50% white cement and 50% ordinary cement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Precast terrazo tiles 22 mm (twenty two millimetre) thick with graded marble chips of sizes upto 12 mm (twelve millimetre), in skirting and risers of steps not exceeding 30 cm in height, on 12 mm (twelve millimetre) thick cement plaster 1:3 (1 cement : 3 coarse sand), jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of : Light shade pigment using white cement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Precast terrazo tiles 22 mm (twenty two millimetre) thick with graded marble chips of sizes upto 12 mm (twelve millimetre) , in skirting and risers of steps not exceeding 30 cm in height, on 12 mm (twelve millimetre) thick cement plaster 1:3 (1 cement : 3 coarse sand), jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of : Medium shades pigment using 50% white cement and 50% ordinary cement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Chequered terrazo tiles 22 mm(twenty two millimetre) thick with graded marble chips of size up to 6 mm (six millimetre) in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm (twenty millimetre) thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Medium shade pigment using 50% white cement, 50% ordinary cement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Marble chips skirting /dado rubbed and polished to granolithic finish, top layer 6 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from smallest to 4 mm (four millimetre) nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume medium shade perment with 50% including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (three hundred into three hundred millimetre) (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, ivory, Grey, Fume Red Brown, laid on 20 mm (twenty millimetre) thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m (three point three kilogram per squaremetre) including pointing the joints with white cement and matching pigments etc., complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm (twelve millimetre) thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm (three point three kilogram per square metre) including pointing in white cement mixed with pigment of matching shade complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm (eight millimetre) diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required 0.63mm thick with size cutting not less than 275 sqm including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing ridges or hips of width 60 cm (sixty centimetre) overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm (eight millimetre) dia G.I. limpet and bitumen washers complete. 0.63 mm (zero point sixty three millimetre) thick with zinc coating not less than 275 gm/m² including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing valleys of 90 cm (ninety centimetre) wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete 1.60 mm (one point sixty millimetre) thick with zinc coating not less than 350 gm/m² including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point sixty six millimetre to two millimetre) thick in eaves board/facia/ soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . (Base members of steel work shall be measured & paid separtely).

Providing and fixing 15 cm (fifteen centimetre) wide, 45 cm (fourty centimetre) overall semi- circular plain G.S. sheet gutter with iron brackets 40x3mm (fourty into three millimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. : 0.80 mm 9zero point eighty millimetre) thick with zinc coating not less than 275 gm/m2 including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately) 6mm thick cement fiber board as per IS:14862 including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing Single socketed pipes 110 mm (one hundred ten millimetre) diameter on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . ( I ) Coupler :110 mm (one hundred ten millimetre)

( II ) Bend 87.5° 110 mm (one hundred ten millimetre) bend

( III )110 mm (one hundred ten millimetre) Shoe

Providing and fixing unplasticised -PVC pipe clips of design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty into fifty into fifty millimetre) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( one cement: 4 coarse sand) and making good the wall etc. complete. 110mm (one hundred ten millimetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

15 mm (fifteen millimetre) cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

15 mm (fifteen millimetre) cement plaster on rough sides of single or half brick wall finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

6mm (six millimetre) cement plaster of mix: 1:3 (1cement :3 Fine sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 (fifty) gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.: New work (Two or more coats applied @ 1.43 litre/ 10 sqm (ten square metre) Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm( ten squaremetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm (ten square metre) over an under coat of primer applied @0.75 ltr/10 sqm (ten square metre) of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (ten square metre) over an under coat of primer applied @ 0.80 ltr/ 10 sqm (ten square metre) of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

French spirit polishing : Two or more coats on new works including a coat of wood filler including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and applying white cement based putty of average thickness 1 mm (one millimetre) , of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Wall painting two coats with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying 60mm (sixty millimetre) thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm (fifty millimetre) thick compacted bed of coarse sand, filling the joints with line sand etc. all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying matt finished vitrified tile of size 300x300 x 9.8mm (three hundred into three hundred into nine point eight millimetre) having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm (twenty millimetrethick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality : Rectangular shape 600x450 mm (six hundred into four hundred fifty millimetre) internal each dimensions including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Supplying, filling, spreading & leveling gravels of size range 5 mm (five millimetre) to 10 mm (ten millimetre) , in the recharge pit, over the existing layer of boulders, in required thickness including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Supplying, filling, spreading & leveling stone boulders of size range 5 cm (five centimetre) to 20 cm (twenty centimete) in recharge pit, in the required thickness including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm (one point five millimetre to two millimetre) in recharge pit, in required thickness over gravel layer including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . 15 mm (fifteen millimetre) nominal bore

20 mm (twenty milimetre) nominal bore

32mm (thirty two millimetre) nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :. 25 to 40 mm (twenty five to fourty millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 20 mm (twenty millimetre) nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00(one) metre spacing. This includes the costs of cutting chases and including testing of joints completeincluding carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . Concealed work, including cutting chases and making good the wall etc. 2025 (25 mm OD) pipe

1620 (20 mm (twenty millimetre) OD pipe

1216 (16 mm (sixteen millimetre) OD) pipe

Providing and fixing 10 ltr. (ten litre) P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required size white viterous china orrisa pattern w.c pan of size 580x440 mm (five hundred eighty into four hundred fouty millimetre) with intergal type foot rest including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. Pan with ISI marked white solid plastic set and lid including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm (five hundred fifty into four hundred millimetre) with a pair of 15 mm (fifteen millimetre) C.P. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimetrE0 C.P. brass pillar taps, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm (fifteen millimetre) C.P. brass pillar tap including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm (five hundred eight into three hundred eight into three hundred fifty millimetre) with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Single half stall urinal with 5 (five) litre P.V.C. automatic flushing cistern including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm (fourty millimetre) , including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm (five hundred ten into one thousand fourty millimetre) bowl depth 250 including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32mm (thirty two millimetre) dia including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work 40mm(fourty millimetre) dia including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 600x450 mm (six hundred into four hunded fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms (eight hundred ten grams) 15mm nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing C.P.Mixer for kitchen sink with casted swinging CON-CHR-309KNM jaquar or equavalent complete In all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing C.P. brass shower rose with 15 or 20 mm (fifteen or twenty millimetre) inlet :100mm (one hundred millimetre) dia including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimetre), breadth 102mm (one hundred two millimetre), height of 75mm (seventy five millimetre) with concealed fitting arrangements, weighing not less than 106 gms (one hundred six grams) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 8 mm (eight millimetre) dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . 15mm (fifteen millimetre)

20mm (twenty millimetre)

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimete) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 150 mm (one hundred fifty millimetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90 mm (one hundred ten millimetre into ninety millimetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . I) 110mm (one hundred ten millimetre) dia

II) 150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . I) 110mm (one hundred ten millimetre) dia

II) 150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC plain double equal branch ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . I) 110mm (one hundred ten millimetre) dia

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . I) 110mm (one hundred ten millimetre) dia

II) 150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc.complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . I) 110mm (one hundred ten millimetre) dia

II) 150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . I) 110mm (one hundred ten millimetre) dia

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slabwith 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm (twenty millimetre) nominal size, foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm (fourty millimetre) nominal size, inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm (twenty millimetre) nominal size finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm (ninety into eighty centimetre) and 45 cm (fourty five centimetre) deep including C.I. cover with frame (Light duty) 450x610 mm (four hundred fifty into six hundred ten millimetre) internal dimentions, total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing soak pit 1.20x1.20x1.20 m (one point twenty into one point twenty into one point twenty metre) filled with brickbats including S.W. drain pipe 100 mm (hundred millimetre) diameter and 1.20 m (one point twenty metre) long complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Ranjit Singh Kanwar