GMC - Kollam- Providing parking facilities for Medical College staff

Amount

Appendix A

2.1.1 : Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

2.30.1 : Excavating holes more than 0.10 cum & upto 0.50 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil; as directed within a lead of 50 m and lift up to 1.5 m.All kinds of soil

4.1.4 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 )1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size)

50.10.2 : Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

od88693/2018_2019 : Providing and fixing false ceiling with"E" board classic tile or Sheet equivalent make 10mm thick ceiling of approved quality (based on 50.12.5.1) (LS based DSR 12.26.1)

od88694/2018_2019 : Roofing with shingles tiles over E- board ceiling using bitumen felt etc.

26.24.S.A.R.2 : Fill the groove (i.e. 2-3mm gap between boards),taping and jointing 8mm thick fiber cement board and 12.5mm thick gypsum plaster boards with epoxy based sealing compound, Acrylic based sealing compound, Non woven reinforcement Tape as per direction of Engineer in charge.(Use a flexible knife so that no air bubble is entrapped. Allow 1-2 hours gap. Once hard tacky or set, apply a coat of Acrylic based sealing compound paste to flash fill the beveled area. After 2-4 hours go on to repeat a skin coat with Acrylic based sealing compound to securely embed the 40mm width (non woven reinforcement Tape. Use only flexible steel knife, such as provided with packs, to avoid air entrapment within compound. After overnight drying shrinkage apply a coat of acrylic based sealing compound to compensate shrinkage. Finally cover the bevel portion with any suitable overall skin coat with a desired full surface-leveler material).Fill the groove (i.e. 2-3mm gap between boards),taping and jointing 8mm thickfiber cement board and 12.5mm thick gypsum plaster boards with epoxy basedsealing compound, Acrylic based sealing compound, Non woven reinforcementTape as per direction of Engineer in charge.(Use a flexible knife so that no airbubble is entrapped. Allow 1-2 hours gap. Once hard tacky or set, apply a coatof Acrylic based sealing compound paste to flash fill the beveled area. After2-4 hours go on to repeat a skin coat with Acrylic based sealing compound tosecurely embed the 40mm width (non woven reinforcement Tape. Use onlyflexible steel knife, such as provided with packs, to avoid air entrapment withincompound. After overnight drying shrinkage apply a coat of acrylic basedsealing compound to compensate shrinkage. Finally cover the bevel portionwith any suitable overall skin coat with a desired full surface-leveler material).

P I Noushadassociates

M ASHARAF

Bidder Name

M ASHARAF

P I Noushadassociates

C. Sasikumar