CERTAIN REPAIRS TO JOINERY, FLOORS, PLASTER AND SANITARY FITTINGS ETC IN OTM ACCNS INCLUDING ABHERA CAMP UNDER AGE B/R II AT MILITARY STATION KOTA

Amount

Demolition of cement concrete un-reinforced in ground floors and pavings n.exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggreate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L for 50mm thick PCC 1:2:4 mix type B1 (Using 20mm graded stone agg) as in flooring, finishing surfaces even and smooth with using extra cement, complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors, levelling course etc, complete all as specified and directed.

Supply only glass dividing strips 3 mm thick and 38 mm wide, fixed in position to conform to design, complete all as specified and directed. (Rate for fixing shall be deemed included in the item of PCC flooring).

Dismantling of corrugated or semi corrugated asbestos cement sheets in roof covering including ridges, complete all as specified and directed.

S&F 6mm thick asbestos cement corrugated or semi corrugated sheets in roofs, walls etc. and fixed with 'L' or 'J' hook or cranked hook bolts, complete all as specified and directed.

Ditto but except AC sheets, complete all as specified and directed. (Note: Serviceable dismantled AC sheets shall be reused under this item.)

M&L for 6 mm thick AC two piece adjustable ridge, serrated ridge for corrugated or semi corrugated sheets fixed with L type or J type or cranked hook bolts, complete all as specified and directed.

Ditto but except AC ridge, complete all as specified and directed. (Note: Serviceable dismantled AC ridge shall be reused under this item.)

Dismantling timber fillets, rails, posts, rafters, purlins etc, under 40 Sqcm in section, unframed work, complete all as specified and directed.

S&F 2nd class hard wood (Sal) as in plain fillets square, rectangular or triangular in sec clean sawn with nails area exc 06.00 Sqcm but n.exc 13.00 Sqcm. complete all as specified and directed.

S&F 2nd class hard wood (Sal) as in plain fillets square, rectangular or triangular in sec clean sawn with nails area exc 13.00 Sqcm but n.exc 25.00 Sqcm. complete all as specified and directed.

M&L Mild Steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe 410-W (Gde - E-250) quality-A, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M&L mild steel work as in Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Fixing only mild steel work as in wind ties, complete all as specified and directed. (Serviceable dismantled wind ties shall be reused under this item).

M&L for PCC 1:3:6 mix type C-1 (Using 20mm graded stone agg) as in coping, lintels, door cills etc including weatherings, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L applying 2 coats of synthetic enamel paint over a coat or red oxide primer on steel surfaces, not exceeding 10 cm in width or girth, when unconnected with other painting or when painted in different tint, incl preparation of the new surfaces, complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials new or old of any description and girth not otherwise described and treated with two coats of creosote oil, complete all as specified and directed.

S&F fiber glass reinforced translucent corrugated sheeting 2 mm thick with two corrugation side lap fixed with L-type or J-type or cranked hook bolts complete all as specified and directed.

Dismantling plain or corrugated steel sheeting of any gauge/thickness from roofs and wall covering, complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridges, hips, valley, gutter, flashings etc and the like, fixed with self tapping screws as specified, complete all as specified and directed.

S&F 0.63 mm thick CGI sheet with two corrugation side lap as in roof covering with grade of zinc coating 275, fixed with 'J' type Hook or 'L' type Hook and washers, complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, wall cladding etc, fixed to iron/wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good distrurbed ground (posts embedded in concrete), complete all as specified and directed.

M&L PCC 1:3:6 type C-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc complete all as specified and directed.

S&F mild steel work in tubular trusses/purlins/rafters/posts etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 complete all as specified and directed.

S&F 11 to 15 mm dia MS screw bolts (Machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut, length of bolt not exc 5 cm but n exc 10 cm long, complete all as specified and directed.

S&F in repair shelf of PTMT fixed with and including CP brass screws and wooden/PVC cleats (Minimum weight 300 gms), complete all as specified and directed.

Dismantling wall and ceiling boards (plywood) or installation boards/slabs/blankets, any thickness including cover fillets, complete all as specified and directed.

M&L 4 mm thick high pressure steam cured Non asbestos fibre cement reinforced multipurpose building boards fixed or laid/ inserted to aluminium framework with screws alongwith anodised aluminium snap grid frame work for false ceiling (grid size 605x605mm) with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long and applying two coats of white wash on celing boards afterpreparation of surfaces, complete all as specified and directed.

M&L 4mm thick asbestos cement plain building boards, fixed to timber framework with screws as in ceiling, flat or sloping and applying two coats of white wash on ceiling boards after preparation of surfaces, complete all as specified and directed.

Taking down cement plaster any description/thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Demolition of brick work/stone boulder masonry, built in CM incl all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (old size fly ash bricks), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

Ditto but except bricks, complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15 mm thick rendering on other than fair faces of brick/concrete surfaces in two layers, consisting of 10 mm thick in CM 1:6 and over that 5 mm thick in CM 1:4 using WPC, finishing surfaces even and smooth with out using extra cement and over it applying two coats of cement based paint over a coat of cement primer after preparation of surfaces, complete all as specified and directed. (WPC shall be measured and paid separately.)

M&L rendering 5 mm thick in CM 1:3 on concrete surfaces of ceiling, finished even and smooth with out using extra cement and over it applying three coats of white wash after preparation of surfaces, complete all as specified and directed.

Supply only approved integral water proofing compound, complete all as specified and directed.

M&L two coats of oil emulsion distempering on walls over a coat of chalk whiting after preparation of new plastered surfaces, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of walls, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of ceiling, complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L chequered cement concrete tiles 30 cm x 30 cm by 20-22 mm thick, set jointed and pointed in neat cement slurry with grey cement and pigments as in floors, laid over and including 15 mm thick CM 1:6 screed bed, complete all as specified and directed.

M&L for non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for light coloured vitrified tiles, 10mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exceeding 10 cm girth as in brick wall complete all as specified and directed.

Supply, fixing, laying & testing 15 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, including taking up or down existing steel tubing, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, including taking up or down existing steel tubing, complete all as specified and directed.

Supply, fixing, laying & testing 25 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, including taking up or down existing steel tubing, complete all as specified and directed.

Taking up or down 15 mm bore GI tubing including cleaning and refixing the same with and including new GI fittings in new or old position (Wall, Ceiling, floor etc), complete all as specified and directed.

Taking up or down 20 mm bore GI tubing including cleaning and refixing the same with and including new GI fittings in new or old position (Wall, Ceiling, floor etc), complete all as specified and directed.

Taking up or down 25 mm bore GI tubing including cleaning and refixing the same with and including new GI fittings in new or old position (Wall, Ceiling, floor etc), complete all as specified and directed.

S&F pillar taps, cast copper alloy, with capston heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

S&F in repair bib taps, cast copper alloy, with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket, complete all as specified and directed.

S&F in repair bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair stop valve 15 mm nominal bore cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F in repair stop valves 15 mm nominal bore, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair stop valves 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair bib tap standard of PTMT any colour, high pressure, screwed for iron pipe and fixed, 15 mm bore (minimum weight 90 gms), complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest including one CI 'P' or 'S' trap and providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

S&F vitreons china wash down water closet pan, padestal type, white, including recessed bottom PVC seat cover of white colour and mild steel chromium plated hinging device but excluding flushing cistern, flush pipe and fixing bolt and making connections to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc, fixed in repairs, complete all as specified and directed.

S&F in repair 10 Ltr capacity PVC low level flushing cistern, top push type with inlet ball valve, PVC float, brackets including superior quality PVC flush pipe of 32 mm dia, complete all as specified and directed.

S&F in repair 15 mm bore CP brass wall mixer for mixing hot and cold water with two CP brass wall flange, screwed down for iron pipe and fixed, complete all as specified.

S&F in repair 'D' type towel rail 60 cm long, made of stainless steel, fancy type, 20 mm dia complete fixed with steel screws complete all as specified and directed.

S&F in repair swivel shower rose of PTMT any colour for fixing with 15 mm pipe (minimum weight not less than 40 gms) with shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of PTMT (minimum weight not less than 40 gms), complete all as specified and directed.

M&L for preparation of old previously treated surfaces of walls and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of old previously treated surfaces of ceiling and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of old previously treated surfaces of walls and applying one coat of colour wash, complete all as specified and directed.

M&L for preparation of old previously treated surfaces of walls and applying one coat of distemper oil emulsion, complete all as specified and directed.

M & L for preparation of old previously treated wood or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M & L for preparation of old previously treated steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old previously treated surfaces of walls and applying one coat of cement based paint, complete all as specified and directed.

M&L for preparation of old previously treated surfaces of walls and applying two coats of distemper oil emulsion, complete all as specified and directed.

M&L for preparation of old previously treated surfaces of walls excedding 10 cm in width or girth and applying one coat of plastic emulsion paint, complete all as specified and directed.

M&L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channel and drains, complete all as specified and directed.

a) Extra for forming fair finished drain or channel 30 cm inner girths in cement concrete using extra cement incl forms, moulds, mitered/stopped ends etc, complete all as specified and directed.

b) Add to or deduct therefrom for each additional 25 mm girth or part thereof.

Demolition of Stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for machine cut kota stone slab as in skirting, dado, risers etc, 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 10 mm thick CM 1:4 backing, complete all as specified and directed.

M&L in repair Granite stone (of any type) slabs, bright finished 20mm thick machine cut fixed as in cooking platform, laid over and including 10 mm thick screed bed or bedding layer of 1:6, bedded and jointed with grey cement slurry and pointed in white cement mixed with pigment to match the shade of granite stone including cutting, polishing, rounding of exposed edges, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

M&L 1 mm thick Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges, 150 mm dia, complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F PVC (SWR) bends of any radius, 100 mm bore, complete all as specified and directed.

S&F PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F PVC (SWR) bends of any radius, 75 mm bore, complete all as specified and directed.

S&F in repair grating doom of 100 mm dia, made of PTMT with waste hole (Minimum weight 25 gms), complete all as specified and directed.

S&F in repair grating doom of 125 mm dia, made of PTMT with waste hole (Minimum weight 40 gms), complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 500 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position, fixed in repairs, all as specified in SSR Part I and as directed

S&F in position rotational moulded polyethylene water storage tanks 1000 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position, fixed in repairs, all as specified in SSR Part I and as directed

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in repairs 15 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in repair 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

Dismantling cast iron or reinforced concrete concrete drain pipes 100 mm bore, jointed in CM and taking out from trenches if required, complete all as specified and directed.

Dismantling cast iron or reinforced concrete concrete drain pipes 75 mm bore, jointed in CM and taking out from trenches if required, complete all as specified and directed.

S&F sand cast iron soil, waste and vent pipe 100 mm bore in any length with or with out ears with cement joints laid in trenches or in floor complete all as specified

S&F sand cast iron soil, waste and vent pipe 75 mm bore in any length with or with out ears with cement joints laid in trenches or in floor complete all as specified

S&F 100 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F 75 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F 100 mm bore CI branch pieces, single (equal or unequal) ordinary or inverted or with parallel branches, complete all as specified and directed.

S&F 75 mm bore CI branch pieces, single (equal or unequal) ordinary or inverted or with parallel branches, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, bore of pipe 100/110 mm, complete all as specified and directed.

S&F in repair PVC connection, 15 mm size with two PTMT nuts, length of connection 450 mm, complete all as specified and directed. (Make - India Prayag/Polytuf)

S&F in repair 25 mm dia stainless steel curtain rods with fixing brackets, stops, rollers etc, complete all as specified and directed.

S&F PVC (SWR) floor trap, incl jointing to waste pipe with solvent cement, diameter of outlet is 75mm, complete all as specified and directed.

S&F in repair vitreous china wash hand basin white with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl PVC waste pipe of 32 mm bore, one pair of 600 mm long cast iron brackets, complete all as specified and directed.

S&F in repair plastic water closet seat cover for EWC, white, closed pattern with recessed bottom and mild steel chromium plated hinging device, complete all as specified and directed.

S&F 3mm thick sheet glass, obscured or frosted on one side, ordinary quality and glazing with metal clips in squares n.exe 0.50 Sqm in each pane, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down shutters of any description not exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and directed.

Refixing of shutters n. exc. 1 Sqm each in same or other opening after easing and adjusting including renewal of screws etc. complete all as specified and directed

Refixing of shutters exc. 1 Sqm but n. exc. 2 Sqm each in same or other opening after easing and adjusting including renewal of screws etc. complete all as specified and directed

M&L for 35 mm thick factory made, plain framed, panelled shutters (two panels), with lock rail and panel of panels of 9 mm thick BWP commercial ply or of venered particle board 12 mm thick with commercial veneering on both faces with rails and style of IInd class hard wood (Hollock). The size of rail and stile as per IS : 1003 (part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

M&L for 35mm thick 2nd class hard wood (Sal) glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc, edges of framing plain, chamfered or rounded, fitted with cut or mitered beads, size of members of shutters as specified in clause 8.24(a) of SSR part I and fitted to chowkhats, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and directed.

M&L for 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane, including hacking out old broken glass (any thickness, size, quality or description) from wooden frames glazed with putty or fixed with beads, complete all as specified and directed.

S&F in repairs 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 100 mm long and fixed complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed all as specified and directed.

S&F 125 mm Hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F for mild steel work as in bands, straps, hold fasts, clamps and similar small articles including cutting to shape as directed, drilling holes etc. conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces, exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for PCC 1:3:6 mix type C-1 (Using 20mm graded stone agg) as in bed blocks for fixing hold fasts, bolts etc, complete all as specified and directed.

S&F in repairs door closer hydraulically regulated, aluminium die cast body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm width and weight between 61 to 80 Kg and fixed, complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F in repairs Wire netting of galvanised steel wire 2.00 mm dia fixed with tinned tacks of wire staples, size of mesh 20 mm, complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, medium weight, cold rolled and fixed with screws, complete all as specified and directed.

S&F mortise lock, made of brass, vertical type, size 100 mm, mild steel, 4 levers complete all as specified and directed.

Taking down steel windows or ventilators of any description and size from any position, complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of zinc chromate primer, complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, including one shop coat of zinc chromate primer, complete all as specified and directed.

S&F steel windows/ventilators with top hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, including one shop coat of zinc chromate primer, complete all as specified and directed.

M&L Running welding in repairs n. exc. 6 mm metal thickness to be welded, complete all as specified and directed.

M&L for welding in repair n. exc. 2.5 cm in length, thickness of metal to be welded n. exc. 6 mm complete all as specified and directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed.

S&F 18/19 mm thick block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame work, complete all as specified and directed.

S&F Anodised aluminium window/door/ventilators frame with one or more rebtes including jointing cleats for fixing etc, complete all as specified and directed.

Taking down aluminium door/window shutters, carrying out minor repairs/adjustment including providing rubber beading, aluminium snap beadings etc and refixing in same position, complete all as specified and directed.

S&F in replacement top rail/bottom rail/lock rail/stiles of aluminium door/window shutter, repair/adjustment including necessary materials such as aluminium sections of required size, cleats, rubber beading, handles etc including taking down and refixing of shutters, complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (2 No.) suitable handle (1 No), complete all as specified and directed.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F in repairs 25 mm dia fancy type drapery rods with natural wooden finish and wooden ornamental attachment at both ends and one set of ornamental decorative finish wooden clamps and matching rings minimum 8 Nos in per RM, complete all as specified and directed.

S&F in repairs PTMT alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed, complete all as specified and directed. Make - India Prayag cat part No. 551

M&L for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chromate primer, complete all as specified and directed.

S&F superior quality 32 mm bore PVC waste pipe suitable for sink/WHB/Urinal, minimum length 0.90 m, complete all as specified and directed.

S&F in repair sink with draining board made of stainless steel 1mm thick with plugs, washers incl brackets of suitable angle iron, 32 mm dia superior quality PVC waste pipe, 32 mm dia CP brass waste coupling and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F shower rose, chromium plated brass, fancy type, 65 mm size with swival joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed.

S&F glass shelf assembly of 6 mm thick glass, 12 cm wide and 60 cm long and CP guards of approved quality and fixed to wall with CP brass screws etc, complete all as specified and directed.

S & F 15 mm dia chromium plated brass centre hole wash basin mixer with accessories, fixed to wash basins for mixing hot and cold water, screwed down for 15 mm bore GI pipe, complete all as specified and directed.

S&F ABS body health faucet with 1.5 mtr long easy flex tube in chrome finish and wall hook, complete all as specified and directed.

M&L for complete removal of existing treatment from previously treated plastered surfaces of walls and applying two coats of modified exterior acrylic emulsion paint over a coat of primer, complete all as specified and directed. (Make: Asian paints - Apex Ultima, ICI Dulux - Weather Shield Max, Berger - Weather Coat Long Life, Acro Paints - Acroguard 3X)

ONKAR ENGINEERS

Aditya Enterprises

S.S Enterprises

Pioneer Enterprises

TARKESHWAR DASS CONSTRUCTION COMPANY