Mangalam Project - Maintenance and repaires of canal shutters of LB Main canal ch. bet 0-000 to 24-500 km.

Amount

Supply, Fabrication, Painting and Erection of CANAL SHUTTERS at LBC to RBC Diversion

od18839/2018_2019/MH : DISMANTLING and STACKING the old corroded CANAL shutter, Hosting mechanism, Screw rod and C groove

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

od17709/2018_2019/MH : Fabrication and supply of STRUCTURAL STEEL CANAL GATES and accessories as per approved specifications and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

od18446/2018_2019/MH : Fabrication and supply of HOISTING BRIDGE UNIT of CANAL GATE SHUTTERS in structural steel confirming to IS2062 Gr. as per approved specifications and directions of departmental officer at site including cost of labour, machinery, incidental and handling charges etc. complete but excluding material already supplied etc. complete.

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

85.115 : Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od17712/2018_2019/MH : ERECTION of the CANAL GATE safely in the groovesErection of the gate safely in the grooves, assembling and aligning including cost of all machinery, labour, incidental, conveyance, trial run lead & lift etc. complete as per direction of departmental officer at site

od17713/2018_2019/MH : Erection of the HOISTING UNIT and its ACCESSORIES of CANAL GATEErection of the hoisting bridge unit including Screw rod, Worm & Pinion, Platform and Ladder etc. in correct alignment and anchoring it, setting and aligning the covers of hoisting unit etc. complete including cost of all labour, machinery, incidental, conveyance, trial run, lead & lift etc. complete as per direction of departmental officer at site.

od17714/2018_2019/MH : Providing of WORM & PINIONProviding of WORM & PINION having a lifting speed of around 5cm/min for 24 RPM of hand operation including costof all materials, labour, hire charges and conveyance

od17715/2018_2019/MH : Providing EN8 THREADED SCREW ROD of dia 63mmProviding EN8 screw rod 7.5 tonne capacity screw hoist having 1No of EN8 screw shaft having a lifting speed of around 5cm/min for 24RPM of hand operation including cost of all materials, labour, hire charges and conveyance.

od17716/2018_2019/MH : THREAD LESS portion of the screw rod

Supply, fabrication, painting, erection and locking arrangements of Direct Sluice Canal Gates

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.106 : Supply of MS flats including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od17709/2018_2019/MH : Fabrication and supply of STRUCTURAL STEEL CANAL GATES and accessories as per approved specifications and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od17712/2018_2019/MH : ERECTION of the CANAL GATE safely in the groovesErection of the gate safely in the grooves, assembling and aligning including cost of all machinery, labour, incidental, conveyance, trial run lead & lift etc. complete as per direction of departmental officer at site

od18440/2018_2019/MH : Charges for the DRILLING of HOLE for locking arrangement of LIFTING HANDLE of MS Angle/MS Square hollow Section of thickness upto 10mm (hole size upto Dia 24mm)

od18437/2018_2019/MH : DRILLING and FASTENING with EXPANSION BOLT M24x150mm length in concrete including conveyance and labor charges complete.

od18438/2018_2019/MH : SUPPLYING and STACKING of PAD LOCK

DISTRIBUTION BRANCH CANAL SHUTTERS & HOISTING MECHANISMS

15.9.2 : Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od18840/2018_2019/MH : FABRICATION, ERECTION and COMMISSIONING of STRUCTURAL STEEL EMBEDDED PARTS and accessories of CANAL GATES in IS2062 Grade as per approved specifications, drawings and directions of departmental officer at site including cost of all labor, machinery, all leads and lifts, incidental chargers etc. complete but excluding the cost of material already supplied.

od17709/2018_2019/MH : Fabrication and supply of STRUCTURAL STEEL CANAL GATES and accessories as per approved specifications and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

od18446/2018_2019/MH : Fabrication and supply of HOISTING BRIDGE UNIT of CANAL GATE SHUTTERS in structural steel confirming to IS2062 Gr. as per approved specifications and directions of departmental officer at site including cost of labour, machinery, incidental and handling charges etc. complete but excluding material already supplied etc. complete.

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

85.115 : Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od17712/2018_2019/MH : ERECTION of the CANAL GATE safely in the groovesErection of the gate safely in the grooves, assembling and aligning including cost of all machinery, labour, incidental, conveyance, trial run lead & lift etc. complete as per direction of departmental officer at site

od17713/2018_2019/MH : Erection of the HOISTING UNIT and its ACCESSORIES of CANAL GATEErection of the hoisting bridge unit including Screw rod, Worm & Pinion, Platform and Ladder etc. in correct alignment and anchoring it, setting and aligning the covers of hoisting unit etc. complete including cost of all labour, machinery, incidental, conveyance, trial run, lead & lift etc. complete as per direction of departmental officer at site.

od18325/2018_2019/MH : Supply of screw shaft of 50mm outer dia, head pitch of 12.7mm, root dia 37.3 mm using EN -8 shaft including cost of materials, labor, tools etc. complete

od18329/2018_2019/MH : Supply and fixing of Screw hoist consisting of Base plate (Cast Iron- 21Kg), Nut (Cast Iron- 14Kg), Top cover (Cast Iron - 15 Kg), Thrust ball bearing No. 51114, bolt & nuts and screw shaft 50 mm dia to suit the mating nut ,mechanical stopper and handle including cost of all materials, machineries, labor, all lift and lead, incidental and conveyance charges etc. complete but excluding the cost of 50 mm dia screw shaft already supplied.