Construction of 50 Bedded Critical Care Block in Government Head Quarters Hospital at Manapparai in Trichy District

Amount

Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers.

Earth work open excavation by manual means in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification and as direct-ed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five Crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification-Mixing by manual means

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15cm thick well rammed with surface vibrator, watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Supply and filling in foundation and basement with Gravel in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

Brick work in Cement Mortar 1:5 (one cement and five crushed stone sand) using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge. In Foundation and Basement

Brick work in Cement Mortar 1:6 (one cement and Six crushed stone sand) using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.

In ground floor

In first floor

In second floor

In Third floor

In fourth floor

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting above 3.60m upto 4.90m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m (expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2.40 x 3.0m (expandable upto 4.90m) made with outer steelpipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c and with Cross bracings provided at two levels at a spacing of 1.80m etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as vertical slab, side slabs of boxing,vertical drops, facia, vertical wall, etc. using mild steel sheets of size 1200cm x 60cm and 10 BG stiffened with welded mild steel angles of size 40mm x 40mm x 5 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals. MS Channel Section (ISMC 100) shall be provided as a vertical support @1.20m C/C and with Lateral support of Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) & steel pipes of 20mm dia @ required level/spacing etc. complete complying with standard specifcation and as directed by the departmentalofficers. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

For circular columns

Centering for curved surfaces of all RCC items of work

Providing and laying in position, standardised concrete Mix M-20 Grade using In-situ Concrete batching plant/ Ready Mix Concrete (RMC) adopting weigh batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete,improve workability without impairing strength and durability with about (5 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including Conveyance of concrete from batching plant to Work site, Electricity charges and other works & labour cost involved for concrete production, laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

For Ground floor

For First floor

For Second floor

For Third floor

For Fourth floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steelreinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steelreinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)

Cement Concrete 1:5:10 (One cement, Five Crushed stone sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers-Mixing by manual means

Brick partition walls of 11.50cm thickness using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground Floor

First Floor

Second Floor

Third Floor

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 10-12mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.-Mixing By Manual means

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick approved quality and colour laid in Cement mortar bed in 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with water resistant tile epoxy grout for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct. 38/40mm thick

Providing cupboard Shutters using termited water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutters and 1mm thick fixed in the outside of the shutters using fevicolalong with necessary furniture fittings, such as hydraulic hinges, tower bolts, handles, multi purpose locks etc., as directed by the departmental officers.The design pattern, water proof plywood, laminate sheet and other materials should be got approved from Executive Engineer before use on works.

Paving the floor with best quality Double charged Vertified tiles 600 x 600 x 8mm size and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality Double charged Vertified tiles 800 x 800 x 10mm size and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with Self Designed ceramic flooring tiles of size 305 x 305 x 6mm size and variety conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Kota stone slabs of size 600mmx 600mm and above 20mm thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., complete complying with standard speicification and as directed by the departmental officers.(The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Supplying and fixing best approved quality Sinthetic Grey, Paradise and Similar varieties. granite slab 1200mm x 600mm, 16mm to 18mm thicksize for working table arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as directed by the departmental officers

Paving the floor with best approved quality Flammed steel grey granite slab 1200mm x 600mm, 16mm to 18mm thicksize and Variety with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Dadooing with printed design colour glazed tiles of size 300 x 450 x 8mm conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Granite Stone Slabs Sinthetic Grey, Paradise and Similar varieties. of 1200x600 of 18/20mm thick size and Variety with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Paving the floor with Tactile Paver Type of New Tek BT Yellow Colour Ceramic Tiles of size 305 X 305 X 15mm for Vision Impairment Person. conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thickincluding mortar plasticizer at 200ml per 50Kg of cement used , hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers.( The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before use on work

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three P - sand), 12mm thick in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Providing Polymer Coating (Water Proof Coating) for sunken Portion of toilet with following specification and the surface shall be cleaned to remove all dust, foreign, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred throughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Supplying and Fixing of Dye Cast letters of following size to suit the Architectural elevation drawings given for the including Cost ,conveyance and all other materials and Labours involved etc., complete and as directed by the Department Officers.

Dyecast letters 25cm size

Dyecast letters 37cm size

Emblem 45cm Size

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum- Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents /Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos.(f) Flow Meter - 1 No. 20” Filter with Housing - 1 No. Low Pressure Switch - 1 No.,Level Switch - 1 No. &Necessary CPVC Pipes and Fittings.The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact 500 Lit Capacity

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETYFIRST / EQUIVALENT

Providing Vinyl Flooring 2mm thick etc., complete complying with standard speicification and as directed by the departmental officers.

Supplying, fabricating, erecting and fixing Hilux (or) equivalent board false ceiling upto a ceiling height of 4.5m from floor level. Plain sheet

Supplying and fixing of SS False Ceiling etc., complete complying with standard speicification and as directed by the departmental officers.

Supplying and fixing of SS Wall Cladding etc., complete complying with standard speicification and as directed by the departmental officers.

Supplying, fabricating and fixing in position factory made Stainless Steel Flush Door Shutter 35mm thick using SS 304 Grade 1.6 mm thick, Stainless Sheets on both sides (Equivalent to IS 6911-04 Cr. 19, Ni 9) minimum 8-8.5% nickel and 18% chromium sourced from original stainless steel manufacturer with view panel size 30mm x 45mm made up of 6mm thick clear toughened glass fitted with double side adhesive tape and finished with dowconing silicon sealant, floor pring for each shutter, consealed tower bolt, suitable stainless steel locking arrangement and other necessary furniture fittings of approved quality. The vertical styles and other frame members and cross stiffeners shall be of same quality stainless steel box section of suitable size and thickness with proper core material as prescribed by the Departmental Officers

Supplying and fixing of SS Sink of size 1200 x 550 x 180mm etc complete as directed by the departmental officers.

Supplying and fixing in position best approved of BIS quality 160mm dia PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. Third Floor

Supplying and fixing Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc.,

Supplying and fixing of Solid core Flush shutters with Teak ply on both side with teak wook lipping alround 35 mm thickness and necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 3 Nos of SS 304 Grade Parliament Hinges of Size (125mm x 150mm) , 2 Nos 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers - Single leaf.

Supplying and fixing of Solid core Flush shutters with Teak ply on both side with teak wook lipping alround 35 mm thickness and necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 6 Nos of SS 304 Grade Parliament Hinges of Size (125mm x 150mm), 3 Nos. 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers - Double leaf.

Fabricating Supplying and fixing in position of Aluminium anodised Powder Coated of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: [email protected] kg/m and Bottom rail: 100x44.45x2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m,Alu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1 Nos., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bushincluding cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge. With floor spring and hinges.

Supplying, fabricating and fixing in position of Aluminium anodised Powder Coated of double leaves door with half panelled with 12mm thick bothside prelaminated partile board at bottom and half glazed using 5.50mm thick Plain glass at top. The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section with Vertical & Top rail: [email protected] kg/m Bottom rail: 100x44.45x2.50mm@ 1.974 kg/mLocal rail : 50x44.45x2.5mm @ 1.292 kg/mAlu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/mAlu. Handle: 100x30mm @ 0.988 kg/m the and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 2 Nos., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 2Nos ., lock-1No., Door stopper with rubber bush including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc. complete.All the Alu. Section are to be anodised with matt finish under electricaly controlled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge. With floor spring and hinges.

Supplying and fixing of Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Fabricating Supplying and fixing inposition Aluminium anodised natural colour matt finish Two track sliding hatch window in all floors with Alu. Section of Outer Vertical frame : 62x31.50x1.50mm @0.875 kg/m,Outer top & bottom gutter frame: 61.98 x 39.30 x 1.50mm @ 0.778kg/m,shutter vertical: 36.60x18x1.50mm@ 0.439kg/m, Shutter horizontal: [email protected]/m with necessary accessories such as Lock, handle, wheel arrangements including supplying and fixing 8mm thick both side prelaminated partical board including cost of all materials, labours, power consumption required for fabrication, drilling holes in RCC column slab, masonry walls wherever necessary with power drills to the required extent and make good to the original condition after fixing and also as directed. All the Aluminium sections are to be anodised with matt finishunder electrically controlled condtions in accordancewith IS 1868/1962 for an average anodic film thickness of 15 microns etc. complete.

Supplying and fixing PVC sliding door with roller and Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames, 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter including slidng arrangements.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying, fabricating and fixing in position of Aluminium Natural Colour Mat finilsh Fixed Glazing the glass used shall be of 5 mm thickness. The Aluminium Section are to be anodised under electrically controlled condition as per IS 1868/1962 for an anodic film thickness of 15 microns. All the materials should be got approved by got approved by the Executive Engineer before execution of works.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing.The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supplying and fixing of M.S.grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification.

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and fixing of PVC Wall Corner beading etc., complete

Brick Jelly Lime Concrete 1:2:5 using 20mm brick jelly in Lime Mortar 1:2 for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor finish, curing, etc. complete complying with standard specification.(For flooring in toilet portioins except water closet portions)

Painting the wall with Texture finish panit including labour charges etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before use of work).

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position SFRC manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Manufacturing, supplying and fixing 50mm thick Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Supplying, laying and jointing UPVC pipes of Class 5 (having working pressure of 10 kg/ sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works - External water supply above ground level / Below ground level.

40mm dia UPVC Pipe (AGL )- External

32mm dia UPVC Pipe (AGL )- External

25mm dia UPVC Pipe (AGL )- External

20mm dia UPVC Pipe (AGL )- Internal

Supplying, laying and jointing UPVC pipes of Class 5 (having working pressure of 10 kg/ sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works - External water supply above ground level / Below ground level. 50mm dia UPVC Pipe

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements

50mm dia UPVC Union

40mm dia UPVC Union

32mm dia UPVC Union

50mm dia UPVC Elbow

32mm dia UPVC Elbow

25mm dia UPVC Elbow

20mm dia UPVC Elbow

32mm dia UPVC Tee

25mm dia UPVC Tee

20mm dia UPVC Tee

32mmx25mm dia UPVC Reducer Tee

25mmx20mm dia UPVC Reducer

25mmx20mm dia UPVC Reducer Elbow

20mmx15mm dia UPVC Reducer Elbow

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work. 32mm dia GM Gate Valve

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Screw Down Tap

SS Elbow action Tap

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).White Glazed Wash Hand Basin Without Pedestal

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing best approved best quality Stainles steel Health Facet with Stop coak of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works) Nahani Trap of size 100 x 75mm with stainless steel gratings

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid above ground level

75mm dia PVC Soil pipe AGL

110mm dia PVC Soil pipe AGL

160mm dia PVC Soil pipe AGL

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

160mm dia PVC plain Elbow

110mm dia PVC plain Elbow

75mm dia PVC Plain Elbow

160mm dia PVC door Elbow

110mm dia PVC door Elbow

160mm dia Singe Y

110mm dia Singe Y

160mm dia Double Y

110mm dia Double Y

Drilling of 6" or 150mm dia vertical bore in hard rock area to any required depth as directed by the departmental officers including labour charges for inserting casing pipes assembly in the drilled holes which excluding cost of 150mm dia PVC casing pipes of required depth.

Drilling upto 150m

From 151m upto 180m

From 181 upto 210m

From 211 upto 240m

Suppling suitable PVC casing pipe for "6" dia borewell (6Kg/cm2) best approved quality with ISI mark with necessary PVC coupling etc (The PVC pipe should be got approved by departmental officer before execution).

Supplying and fixing of suitable PVC end cap (6Kg/cm2) for 6" dia bore well of best quality with ISI mark. (The PVC end cap should be got approved by the departmental officers before execution)

Supplying of best and approved quality of 40mm dia HDPE pipe of the following size including laying in the bore well and tying with copper wire it etc commplete complying with standard specification.

Supplying and erecting 3 HP ISI make bore well SUBMERSIBLE MOTOR including 3 Phase Panel Board including labour charges with requried accessories for the 3 HP ISI make including Conveyance and Errection charges Electrical connection charges, and trial run for three days etc., complete

Supply and fixing of water proof 3 core 2.5sq.m. flat PVC insulated copper cable for submersible pumpset in the borewell including fixing and tying with copper wire and clamping water pipe etc., complete

Supplying and fixing of 1/2 dia Nylon rope for submersible motor of approved quality in etc.,complete complying with standard specifications.

Supplying and fixing of PVC readymade water tank of 1000 ltrs capacity of best and approved quality with ISI specification labour for fixing etc., Complete.

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Medial Gas Copper Pipeline arrangement to hang on the wall of socket type connection installation of seamless cleaned and degreased non aresenical phosphorous gas copper pipe line with saddles complete with brazing work including all copper fitting (tee, elbow, reducer, coupling) The copper pipelines should be tested suitable for a steam of working pressure of 17.34 kg/ cm2 (17 bar) and confirm to BS 864 Standard with specially made for brazed socket type connection. The medical gas copper pipeline should be tested as per standard and commissioning after painting as per International Code No. IS 2379/1963 Table-V. The pipe lines installed at hte various wings and floors etc., complete as directed by the Departmental Officers as per IS code 12827/1989 & ISO 7396/1987 Specification.

28mm dia

22mm dia

15mm dia

10mm dia

Gas Outlet Points: (Self sealing type - Single / DIN outlet pipe) with 'S' type bracket made up of copper and the out let of non-interchangeable for other gas. The outlet points are brazed with brass bracket with self sealing valve (Stainless Steel) with all accessories and complete set and are covered by plastic cover duly colour coated as per specific gas and button cover etc., complete as directed by the Departmental Officers and as per IS Code 12827/1989 & ISO 7396/1987 Specification.

Brass Isolation Valve suitable for the copper pipe and should be of not lubricated 90 degree turn lever ball valve of reputed make, connected in line with medical gas pipe line system by using suitable size brass valve adopter union, ferrule, nipple, rubber "O" ring, tapion lap and etc. All pipe line regulators shall be capable of controlling pipe line pressure and must compatible with the requirements specified in IS 12827 /1989. All valves should be pneumatically tested for twice the working pressure for the gas line as per IS Code 12827/1989 & ISO 7396/1987 Specification,

28mm dia

22mm dia

15mm dia

Oxygen Manifold arrangement of 2 banks x 12 cylinder each wing with semi automatic control panel which includes contact gauge 2 No., oulet pressure gauge, brass heavy dut IO x regulator 2 Nos., with suitable adopter, flexible SS Hose. Manifold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 12827-1989. Emergency alarms with illuminating display for low/ high pipeline pressure and malfunctioning of system. 1) Manifold top frame with provision for connecting 12 cylinders on right bank and 12 cylinder on left bank with high pressure interconnecting tubing, silver brazing, non return for claping 2 x 12 cylinders and related fastener. The O2 manifold should with stand a pressure of 140kg. / CM2 The installation is commissioned after testing as per standards and painted as per International Code and as directed by the Departmental Officers as per IS Code 12827 /1989 & ISO 7396/1987 Specification .

Nitrous Oxide Manifold Arrangements of 2 banks 3 Cylinder each wing, with automatic control panel which includes contact gauge 2 Nos. outlet pressure gauge, brass heavy duty IOX regulator 2 Nos. with suitable adopter, flexible SS hose. Manifold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 12827 -1989. Emergency alarams with illuminating display for low / high pipe line pressure and malfunctioning of system. 1) 2 x3 cyliner Nitrus Oxide Manifold should be suitable with stand a pressure of 140kg/ Cm2 and above along with high pressure copper annealed tail pipes with end brass adapter suitable for Nitrous Oxide Cyliners and manifold. 2) Top frames comprising of high pressure copper pipe of size 12mm ID 1.5mm wall thick with high pressure brass fittings made of high tensile brass and connetions through non -return valves, high pressure copper tail pipes made of high pressure copper pipe size of 7mm ID 1.5mm thick. 3) The disign of middle and bottom frames should be provided to fit both round and flat bottom cylinders safely with fitted heavy duty regualtor. The Manifold should be tested at 3500 pig as per IS 12827/1989 & ISO 7396 / 1987 Specification.

Supply, installation , testing and commissioning of Compressed Air System of Reciprocating Oil Free Air Compressor belt driven type air compressor with following provisions. As per IS 12827 /1989 & ISO 7396/1987 Specification. a) 10HP Air Compressor - 2 Nos. b) Electric Motor 10 HP - 2 Nos. c) Dol Starter - L&T - 10HP - 1 No. d) Base Frame Kit (for Motor and Compressor)-1set. e) Pressure Switch - 1 No. f) Pressure Gauge - 1 No. g) NRV and Pilot Fittings - 1No. h) Delivery Tube - 1 No. i) Foundation Bolts & Anchor Fasteners - 1 Lot j) Belt Guard - 1 No. k) Air Driver 50 to 60 cfm. capacity - 1No. Drain Ball Valve - 1No. Air Outlet Compressor Room Inside Accessories. Non-Return Valves, Air Pressure Switch, Pressure Gauge, Isolation Valves, Air Filters etc., Inter connecting piping: Mild Steel Pipe of 2" with fittings.

Supply, installation, testing and commissioning of equivalent to Intersoil Rand Receprocating Air Cooled Type (10HP + 5HP) rating Vaccum Pump as per following provsiions. As per IS 12827 /1989 & ISO 7396/1987 Specification. a) Vaccum pump -10HP- 1set b) Electric motor - 5HP - 1 No. c) DOL Starter with OLR - 1 No. d) Vaccum switch - 1 No. e) Vaccum Gauge - 1 No. f) Control frame wth Fittings - 1 No. g) Suction Scrubber - 1 No i) GI & MS fittings- 1 No. j) Brass fittings - 1 No. k) Exhaust Silencer - 1 No. l) Base frame for motro and vaccum pump - 1 set m Pilot line with fittings - 1 set, Vaccum Room & Air Compressor Room Inside

Supply, installation, testing and commissioning of MS fabricated Vertical Mounted Type 1000 liters capacity Compressed Air Receiver with inlet and outlet and drain holes provided suitable to operate with vaccum pump etc as directed by the Departmental Officers.

Flow Meter made up of Brass with Humidifier Bottle Flow Meter should be back pressure compressed and should be accurate gas flow measurement with control range 0-13 litres per miniute. It should meet strict permission and dumbling standard. The meter body should be made of brass materials. The humidifier bottle should be made of unbreadkable polycorbonate material and auto cleavable at 134 degree centigrate. The includes flow meter and its accessories (silicon tube with mask.) The cost of materials including transport, etc., complete as per standard specification and as directed by the Dpartmental Officer and as per IS 12827/1987 & ISO 7396/1987

Ward Vaccum Unit with Gauge both mounted on a collection jar of capacity 600 ml and with a wall bracket for mounting it on the wall. The collection jar should be made of unbreadkable polycarbonate materials which is fully auto cleavable at 134 degree centigrade as per standard specification and as directed by the Departmental Officer and as per IS 12827/1989 & ISO 7396/1987 Specification . The rate includes cost of silicon hose with SS nipple on either side.

Theatre Vaccum Unit: The unit should comprise of two reusable 2000ml shatter resistant bottle. Each made up of ply carbonate material and fully autoclavable at 134 degree centigrade, should have a vaccum regulator with instant ON/OFF switch and three way left, right or both. All the above itesm should be mounted on atrolleyy having free moving castor wheels. (As per IS12827/1989 & ISO 7396/1987)

Bed Head Panel of size 1m, length, height 0-0.30cm and depth of 4". The aluminium powder coated with requirement colour for provisioin points of o2-2 No. Air 1 No. Vaccum 1 No. with double electrical socket with switch 2 Nos. with 2 set with IV - bottle holder fixing to the wall hanging including monitor stand etc., complete.

Supplying and fixing of Cylinder 46 Litre "D" Type Empty Seamless Medical Oxygen Cylinder with Valve and as per IS Code 12827/1989 & ISO 7396 /1987 Specification etc., complete and complying with standard specification.

Supplying and fixing of Cylinder 46 Litre "D" Type Empty Seamless Medical Nitrous Cylinder with Valve and as per IS Code 12827/1989 & ISO 7396 /1987 Specification etc., complete and complying with standard specification.

Supply, installation of Fire fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20 mm dia ball valve and open and close spray nozzie, warm clip, etc., as per the standard pattern of nay reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doiing the dismantled portions to its original condition wherever found necessary., etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of following MS 'C' Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10kg /sq.cm including necessary fittings like MS flange of table 'E' elbows, reducers, gaskets, bolt, nuts wth washerr & joints as per standard method of arc welding, including one coat of metal primer and two coat of Post Officer Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL/ EQUIVALENT

100mm Dia

80mm Dia

Supply, erection, testing commissioning of 80mm dia Heavy Duty Foot Valve including necessary MS flange of table'E' gaskets, bolts & nuts, etc., installed as end of 80mm dia suction pipeline at sump as per the standard method and as directed by the Departmental Officers.

Supply, erection, testing and commissioning Mono Block type Fire fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame incluidng necessary vibration bad mounting etc., including conveying, fixing and incidental charges, etc., complete as per standard specification and as directed by the Departmental Officers (Make: Kirloskar / Equivalent)

Supply, and fixing in position of Fire fighting Application Hose of 63mm dia of 15 metres length binded by coppper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply of Fire fighting Application Application MS Hose Box to keep two number of hoses and 1 no. of branch pipe with nozzie having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling wht rotating wheel to open and close the valve including MS flange of table 'E' bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzie of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, Installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS junction box / false ceiling using fixing accessories llike screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers, (Make: Apollo / Equivalent)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers, (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers, (Make: Ravel / Equivalent)

Supply, Installation , testing and commissioning of Micro Processor based conventional 8 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230/24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental officers.

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 20W 4 feet LED fitting with LED (Higher End) with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 20W 4 feet LED fitting with LED (Higher End) with conduit pipe suspension from the ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of fancy glass shade and 7W / 9W LED bulb

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb

supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600 mm down rod on the existing fan clamp.

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of louvers shutters arrangements for 300 mm (12") sweep (light duty) AC exhaust fan.

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion

Supply and fixing of 2 no. 6A two module socket, 1no.6/16 A two module socket , 2 nos. 6A one module switch, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 20A flush type wall socket 32A DP MCB complete set for AC plug in flush with wall with earth connection.

Supply and fixing of 2way metal box enclosure with 32 A DP MCB (Higher End) in flush with wall and making good of the concealed portion with earth connection.

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of 4 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 2 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 6sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of 4way metal box enclosure with 32 A FP MCB (Higher End) in flush with wall and making good of the concealed portion with earth connection.

Supply and run of 4 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4sq.mm copper wire and making good of the concealed portion with suitable colour

Supply and fixing of 4way metal box enclosure with 63 A FP MCB (Higher End) in flush with wall and making good of the concealed portion with earth connection.

Supply and fixing of Horizontal type 4 way triple pole MCB DB with metal door cover with IP 42 protection in sheet steel enclosure with 1No. 63A 4 pole MCB as incoming 12Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark (Higher End)

Supply and fixing of 4 Way 7 segment TPN MCB distribution board with metal / acrylic double door cover with IP 42 protection in sheet steel enclosure with 63A 4 pole MCB as incoming and 3Nos.40A 30MA DP ELCB and 12Nos.6A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark. (Higher End)

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position.

Supply and fixing of 4way metal box enclosure with 100 A FP MCB (Higher End) in flush with wall and making good of the concealed portion with earth connection.

Supply and fixing of vertical type 4 way triple pole MCB DB with metal door cover with IP 42 protection in sheet steel enclosure with 1No. 100A 4 pole MCB as incoming 4 Nos 6- 32 A SP MCB and 2Nos. 63A TP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark (Higher End)

Supply and fixing of 8 Way 7 segment TPN MCB distribution board with metal / acrylic double door cover with IP 42 protection in sheet steel enclosure with 1 No 100A 4 pole MCB as incoming 3 Nos.40A 30MA DP ELCB and 24 Nos.6A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark.

Supply and Run of 4 of 16 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 16 sq.mm copper wire and making good of the concealed position.

Supply and clamping of 3½ X 185 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3½ X 185 sq.mm PVC Armoured LTUG Cable with earth connection.

Supply and providing cable end termination of 3½ X 185 sq.mm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and Laying of 3 1/2 x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3½ X240sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3½ X 240 sq.mm PVC Armoured LTUG Cable with earth connection.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and Run of 1 of No.8 SWG hard drawn copper in suitable PVC rigid pipe concealed in wall ceiling and making good of the concealed portion with suitable colour.

Supply, erection , testing and commissioning of pedestal type 400 A capacity dust and vermin proof panel board for LT CT metering made up of 16 SWG CRCA sheet of suitable dimensions comprising bus bar chamber, cut out fuse chamber, metering chamber confirming IE rules and as per TANGEDCO norms. The bus bars should be of 4 Nos. of 50mmx6mm copper flats for 3 phases and neutral and No. 8 SWG copper for double earth connection. The buses should be mounted on the SMC bus insulator with proper spacing and should be provided with heat shrinkable sleeves using RYB & Black colours.The bus bar chamber should be segregated from the adjacent chambers by providing 6mm thick hylem sheet. The cut out fuse chamber should be provided with 3 Nos. of 400 A HRC fuse links with fuse base with holders, test terminal block, earth link etc. The metering chamber should be provided with 400A/5A CTs, voltmeter, ammeter, frequency meter, powerfactor meter with suitable lugs, intrconnections and earth connection. The panel board should be provided with one coat of red oxide primer paint and two coats of Siemens grey approved by department officers along with danger board and the panel board should be erected on the suitable pedestal with suitable angle iron frame work and with necessary foundation, bolts & nuts etc.

Supply and fixing of 3 Nos. of 3 phase 400 A aerial fuse unit(500V) on suitable MS sheet covered with 6mm thick hylum sheet on suitable angle iron frame work the tapping pole with necessary 25sqmm PVC insulated copper wire from fuse unit bi-metal clamps.

Supply and Laying of 3 1/2 x400 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3½ X 400sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3½ X 400sq.mm PVC Armoured LTUG Cable with earth connection.

Supply and providing cable end termination of 3½ X 400sq.mm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and fixing of 300mm sweep Wall mounting fan with necessary connection.

Supply, erection, testing and commissioning of 2.0 TR (6000 K. cal/ hr) split type Air conditioner conforming to IS: 1391 (Part-2) 1992 with Amdt No.1 to 2 fitted with compressor operating on non CFC refrigerant suitable for wall mounting for operation on 230V, 50 HZ single phase AC supply with 5 star rating as per BEE specification and capable of performing the functions of 1) Cooling 2) Dehumidifying 3) Air circulating 4) Filtering The installation works for the above split type A.C units includes the following. 1. Mounting / Fitting indoor and outdoor units at their respective locations. 2. Laying refrigerant copper pipe lines of (5/8" & 3/8") 3 meters length including drilling holes in the wall if required. Thickness of the copper tubing shall not be less than 0.7mm. 3. Insulating the suction pipe with expanded polyurethelene foam 5mm thick tubing. 4) Laying 25mm PVC drain pipe of 6 mts. Length to drain out the condensate water being formed in the indoor unit. 5) Leak testing the entire gas unit. 6) Charging refrigerant gas in the unit. 7) Suitable electric wiring to be provided with 3 core 2.5sq.mm PVC insulated copper wire between indoor and outdoor units up to 3 meters length and up to switch within 3 meters of location of indoor unit.

Supply and fixing of 5 KVA electronic automatic voltage stabilizer with input range of 170-270V and output range 200-240 V with high and low voltage cut off and 3 minutes time delay relay suitable for operation on 230V/50Hz single phase AC supply

Supply and fixing of MS stand wall clamp support for mounting outdoor unit of split type AC unit complete.

Supply and fixing of 5/8” and 3/8” copper pipes with insulation foam of 6mm thickness suitable for split type AC unit

Supply, Erection, testing & commissioning of 3 TR norminal capacity ceiling suspended ductable air conditioning unit with the following components. 3 TR capacity ceiling suspended Ductable Air conditioner high tech, low height, low noise level indoor unit with fin and tube type cooling coil, Detachable type drier provided in refrigerant circuit to reduce moisture content multi stage type distributor for feeding equal quantities of the fefrigerant mixture to all the section of the cool, with required valves, directly coupled blower to reduce troubles and wear & tear compared to belt drive blower. Thermostatic expansion valve lift and pull type aluminum framed durable, washable air filter-integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut to improve reliability of compressor, air conditioner high tech outdoor unit with power saving high efficiency sturdy and rugged scroll compressor each with inbuilt internal thermal protector, internal pressure relief valve, Auto reset type HP/LP safety cut out to improve reliability of compressor and condenser shall be made of super slit high efficient aluminum fins mechanically bonded to copper tubes condenser I type coil to be rigidly fixed to unit frame with fasteners, imported condenser fan & fan blades to be statically and dynamically balanced to reduce noise and vibration. The fans are direct driven 3 phase motor with protection. Condencing temperature 130 F for the system operations. (SR-M-1995) (Trauma ICU-8Beds -Second Floor)

Supply ,installation , testing and commissioning of 8.5TR factory assembled double skin AHU with 100mm -45kg/cum PUF Insulated detachable panels ,extruded thermal break aluminium profiles filled with PUF,panel external skin with 0.6 mm preplasticized sheet, panel internal skin with 0.6mm galvanized sheet, AMCA tested DIDW backward/ forward curved centrifugal fan with EFF1 rating motor, drive arrangement with taper lock pulleys for fan and motor, vibration isolators out of heavy duty rubberized mounts, prefilters with 3ply HDPE 50mm thick filters having an efficiency of 90% 10 Micron and 5 Micron, 6row /12FPI deep DX copper cooling coil with copper header and aluminium fins, GI mist arrestor, condensate coil trough with SS-304-20G insulated with 9mm closed cell elastomeric foam, guard for inspection door, out let damper of aerofoil blades & PVC gears, and flexible fire retardant canvass complete with galvanized hardware. Each of the cooling coils will have independent distributers, electronic expansion valve kit, catch all drier, independent DX coil circuit to connectivity to each ODU circuit. Appropriare devices to be installed to monitor the Temperature, Humidity and Diff. Pressure inside the Operation Theatre. (Carrier/ Voltas/ Bluestar make/ Equ.)

Design ,supply , installation, testing and commissioning of DX 8.5TR nominal capacity factory assembled Air-cooled Condensing unit fixed with energy efficient scroll compressor along with grooved copper tube/aluminium fins air cooled condensor coil with anticorrosion coatings,liquid ,accumulator, low noise alumimium propeller condenser fan with Fan motor etc all suitably assembled neatly in heavy duty GSS sheet metal cabinet and duly powder coated as per specification .the unit to include built in safety controls like HP/LP switch power quality protector ,in built thermal / temperature protection.

Supply ,installation , testing and commissioning of 5.5TR factory assembled double skin AHU with 100mm -45kg/cum PUF Insulated detachable panels ,extruded thermal break aluminium profiles filled with PUF,panel external skin with 0.6 mm preplasticized sheet, panel internal skin with 0.6mm galvanized sheet, AMCA tested DIDW backward/ forward curved centrifugal fan with EFF1 rating motor, drive arrangement with taper lock pulleys for fan and motor, vibration isolators out of heavy duty rubberized mounts, prefilters with 3ply HDPE 50mm thick filters having an efficiency of 90% 10 Micron and 5 Micron, 6row /12FPI deep DX copper cooling coil with copper header and aluminium fins, GI mist arrestor, condensate coil trough with SS-304-20G insulated with 9mm closed cell elastomeric foam, guard for inspection door, out let damper of aerofoil blades & PVC gears, and flexible fire retardant canvass complete with galvanized hardware. Each of the cooling coils will have independent distributers, electronic expansion valve kit, catch all drier, independent DX coil circuit to connectivity to each ODU circuit. Appropriare devices to be installed to monitor the Temperature, Humidity and Diff. Pressure inside the Operation Theatre. (Carrier/ Voltas/ Bluestar make/ Equ.)

Design ,supply , installation, testing and commissioning of DX 5.5TR nominal capacity factory assembled Air-cooled Condensing unit fixed with energy efficient scroll compressor along with grooved copper tube/aluminium fins air cooled condensor coil with anticorrosion coatings,liquid ,accumulator, low noise alumimium propeller condenser fan with Fan motor etc all suitably assembled neatly in heavy duty GSS sheet metal cabinet and duly powder coated as per specification .the unit to include built in safety controls like HP/LP switch power quality protector ,in built thermal / temperature protection.

Supply and fixing of 5.5TR & 8.5TR- Laminar Air flow Plenum for SS304 - 1.0 mm Thich casing, Mini Pleat Hepa Filters for 75mm Thick- Flange type, OT Pendant Light provision for 600X600, With SS304-1.2mm Thick perforated sheet. PLENUM SIZE: 1800L X 2400W X 350H High Efficiency particulate Air (HEPA) filter specification: Filter Size : 8 feet x 6 feet x 1 feet Classification : H-13 Construction :Panel Type Efficiency :99.97% Optical efficiency at .3 micron Cleanliness level: Class 100 As per NABH Standard Spacers: Aluminium Initial pressure drop:25 mm W.C Final pressure drop : 75 mm W.C Duct holding capacity:4750gm/Sq.mtr Framing :Aluminium (Box type) Washable : No Test reports to be furnished from approved Government External Quality Assurance Lab/ Agency to meet the testing parameters after commissioning of the AC system with HEPA filter as per NABH standards.

Supply, Fabrication and erection of fabricated ducting made up of Al. Sheets of 22 Gauge thickness.

Sand cement plastering (1:3) of 20mm thickness with chicken mesh for external exposed portion of duct

Supply and providing 4 core 10 Sqmm Cu Flexible Cable in suitable Rigid Pipe on Wall (Compressor Power wiring).

Supply and providing 4 core 6 Sqmm Cu Flexible Cable in suitable Rigid Pipe on Wall (Compressor Power wiring).

Supply and providing 4 core 1.5 Sqmm Cu Flexible Cable in suitable Rigid Pipe on Wall (Control wiring).

Supply and filling of Non CFC Refrigerant Gas R410A.

Supply & fixing of hard drawn copper Refrigerant piping of Size 1/8” (6.40mm) with necessary fitting and clamp etc

Supply & fixing of hard drawn copper Refrigerant piping of Size 7/8” (22.20mm) with necessary fitting and clamp etc.

Supply & fixing of hard drawn copper Refrigerant piping of Size 5/8” (15.90mm) with necessary fitting and clamp etc.

Supply & fixing of hard drawn copper Refrigerant piping of Size 3/8” (9.50mm) with necessary fitting and clamp etc.

Supply, fabrication and fixing of MS channel for mounting the Airconditioing outdoor unit

Supply and fixing of water drain pipe line (1" PVC Pipe)

Supply, fabrication and fixing of MS channel for mounting the Airconditioing Indoor unit

Supply and fixing of flexible canvas connection between indoor unit and ducting and rubber pads, with ceiling Support angle rods etc...

Supply and fixing of 50mm thick anti vibrating rubber pads

Supply and providing of pipeline nitrile rubber insulation for suction line Refrigerant and drain pipe lines as required.

Supply and fixing of Duct Mouth Dampers.

Supply and fixing of Acoustic for initial portion of ducting using 12 mm thick Fibre glass rigid board covered with tissue paper and Aluminium perforated sheet

Supply and Providing Thermal Insulation of 9mm thick Vidoflex with aluminium foil.

Supply and providing civil concrete block for mounting the air conditioning unit.

Supply, Commissioning, testing and handing over of 10KVA Three Phase to Single Phase Output True online Micro processor Controlled Double conversion type,True On line UPS system with Isolation transformer with 12V SMF batteries of required numbers with suitable battery Interlink cables for 2 Hours Back up Time, DC power should be minimum 15000W-Hour and with suitable MS powder coated Rack for Batteries complete with the following specifications. Configuration: True On line double conversion UPS system with pulse width modulation (PWM) Technology using IGBT inverter. RECTIFIER: Full wave(shall fully meet the specified input power requirements ) INPUT: Three phase 320V -460V AC OUT PUT:230V AC± 1% on battery mode FREQUENCY: 47HZ - 53HZ SYSTEM DC VOLTAGE: It may vary from 240V DC to 336V DC depends on the manufaturer, However DC power should be minimum 15000Watts-Hour. INVERSION TECHNOLOGY: Micro processor controlled, pulse width modulation with Instantaneous sine Wave control using IGBT. INVERTER OUT PUT : ( Out put Galvanic Isolation through Double winding Isolation Transformer at Output of Inverter shall be part of UPS Design ) LOAD POWER FACTOR: 0.9 to unity REGULATION : for Balanced load ± 1% For 100% unbalanced load ± 2% FREQUENCY: 50Hz + 0.5% WAVE FORM : Pure sine wave TOTAL HARMONIC DISTORTION : < 3%

OVERLOAD CAPACITY: Inverse Time Characteristic 125% for 10 minutes 150% for 1 minutes EFFICIENCY : 1. Converter – 95% 2. Inverter - 95% 3. Overall >90% ( full load) Operating Temperature : 0 to 45 Degrees centigrade on full load CREAST FACTOR: 3 : 1 RELATIVE Humidity : : 95% at 35 Degree Centigrade non- Condensing CHARGER: Built in solid state automatic float- cum boost charger with constant current, constant, voltage mode of charging along with current limiting features. Ripple in DC shall not exceed 2% when battery is disconnected. PROTECTION( In built) i) output under Voltage ii) output over Voltage iii) output over load iv) output short circuit. v) HRC fuses /output/ battery vi) Battery low trip vii) battery charges current limit. INDICATIONS: i. Mains ON ii. Inverter ON iii. UPS ON battery iv. Load On UPS v. Battery LOW

METERING: i. Output AC Voltage ii.Output DC Voltage / Load details and Frequency By Pass: Manual Centigrade non- Condensing CHARGER: Built in solid state automatic float- cum boost charger with constant current, constant, voltage mode of charging along with current limiting features. Ripple in DC shall notexceed 2% when battery is disconnected. PROTECTION( In built) i) output under Voltage ii) output over Voltage iii) ) output over load iv) output short circuit. v) HRC fuses /output/ battery vi) Battery low trip vii) battery charges current limit. INDICATIONS: i. Mains ON ii. Inverter ON iii. UPS ON battery iv. Load On UPS v. Battery LOW METERING: i. Output AC Voltage ii.Output DC Voltage / Load details and Frequency By Pass: Manual Warrenty: 24 Months from Date of installation for the UPS including battery. (Reputed make like numeric, consul/EQ)

Design, Engineering, supply, fabrication. Erection, Testing commissioning and handing over of 1 No 26 Person passenger cum bed Lift with M/C room, speed 1 m/s with stainless steel panels, Disable friendly, microprocesssor based controller, VVVF drive, Fire rated doors and ARD as per the following Technical Specification. 1.Type of Lift : Passenger cum bed Lift 2. Capacity of Lift : 26 Persons/1768Kgs 3. Speed : 1.00 Meter/Sec 4. Type of Drive: specific Variable Voltage Variable Frequency V3F Drive with Enhanced ride comfort and levelling functions. 5. No. of Floors : 4 (Ground Floor + 3 upper floor) 6. Total Travel : 40feet 7. Levelling Accuracy: High Level Accuracy with Smooth and jerk free stopping. 8. Construction of Car: High quality and suitable thickness S.S. car and S.S false. 9. Position of Machine: Directly above the Lift shaft. 10. No. of Landing Entrance : 4(Ground +3) 11. No. of car Entrance: One in Front only. 12. Car Entrance Door: Power Operated V3F drive side Opening Sliding S.S Doors with VF operation. 13. Landing Entrance Door: Power Operated V3F driver center Opening Doors with provision emergency key opening at all Landings. 14. Lift Well Existing: 2400 mm (width) X 3000 mm (depth). 15. Lift Pit Depth required: 1600 mm 16. Car Size: 1600 mm (Width) X 2400 mm (Depth). 17. Car Clear Opening: 1200 mm

18. Power Supply: 400 / 440 V, 3 Phase, 50Cycles / Sec AC supply for power and 230V 50HZ single phase AC Supply for light at machine room with proper two distinct earth flat of adequate size from ISI earthing at ground floor. 19. Control: Microcomputer (Microprocessor) based Simplex, Collective control with or without attendant. 20. Car Fittings: Compact LED Lighting with 2 Nos. 300 mm Sweep Cabin Fan. 21. Lift Well: R.C.C Construction with Brick Masonry. 22. Indication: UP/DOWN Digital Direction and position indicator for all landing and inside the car. 23. Emergency Alarm Bell: Battery Operated alarm bell with Automatic Charging Device. 24. Emergency Light: Battery operated Light with Automatic Charging Device. 25. Fire Man’s Switch: Include at Ground Floor. 26. Scaffolding: Included. 27. M.S. Sill angels and facis Plates: Included 28. Steel for Lift Machinery: Included 29. Servicing and maintenance: Free comprehensive servicing and maintenance during the guarantee period of one year. 30. Automatic Rescue Device: To facilitate the landing of the lift to the nearest floor at the time of Power Failure. This shall consists of suitable type of Battery system with charger, invertor, under Voltage Protection system etc., Complete with all Accessories. 31. Provision of Intercom with phone: Included 32. Lift Licence: Preparation of Drawing, payment of Charges to CEIG / Lift inspectorate and insurance policies if any and obtaining CEIG safety certificate as per Lift Act. 33. Floor Annunciator with music: Included.

34. SPECIAL FEATURE: A.) Infra-Red colour Sensor with Height Screen. B.) Stainless steel signal fixtures. C.) Vandal Proof Button with S.S Cover. D.) S.S door frames for landing doors. E.) VF Door operator. F.) Calls register Signal. G.) Stainless Steel Facia plate for car operating Panel and landing fixtures. H.) ON-OFF Switch for fan and Light. I.) Voice Annunciator. 35. Lift Duty motor of adequate capacity reduction worm gear, electromagnetic brake with compression springs, over speed Governor, Phase failure and phase reversal relay, alarm Bell, T Guide Brackets for car and Counter weight, Rubber padding under winding unit, car safety Gears, Buffer, Electro Mechanical Door Locks, Emergency Key, Side supporting angles motor Over Load Protection Devices. Final limit Switch, main suspension ropes, Counter weights, Lifting Joist for Mounting the Machineries. 36. Site testing in accordance with IS 14556 should be carried out at the time of handing over. GEARLESS LIFT WITH MACHINE ROOM. 37.All features are included as per differently abled act. 38.2 Hours fire rated doors.

Design, Engineering Supply, fabrication, erection, testing, Commissioning and handing over of 1 No. 240KG service/Dumb waiter lift MRL speed 1 m/s with M.S. Panels, microprocessor based controller, VVVF drive as per following Technical Specification. 1. Type of Lift : Dumb Waiter Service. 2. Capacity of Lift : 200Kg. 3. Speed : 0.34 Metre / Sec. 4. Type of Drive : Single speed Drive 5. No. of Floors : Ground + 3Floors. 6. Over Load warning Indicator and fireman’s Switch to be provided. 7. Design of Car : M.S. Painted with M.S. chequered plate flooring. 8. Position of Machine : Directly above the lift shaft 9. No. of Landing Entrance : One in front Total 4Nos. 10. No. of Car Entrance : One in front only. 11. Car Entrance Door : No Door. 12. Landing Entrance Door : Collapsilble gate M.S. painted with landing door frames. 13.Lift well existing : 1500 mm (Width) x 1200 mm (depth). 14. Lift pit depth available : 1600mm. 15. Car Size : 1100mm (Width) x 1200mm (depth). 16. Car Clear opening : 1000mm wide x 1200mm. 17. Power Supply : 400 / 440V 3 Phase, 50 Cycles / sec AC supply for power and 230 V 50HZ single phase AC supply for light. at machine room. 18. Extremly Extended push buttons with / without Attensant. 19. Car fittings : Bulkhead Fittings. 20. Lift well : RCC construction with brick masonary. 21.Indication : Up / Down Digital for all landings. 22. Minor Builder Work: To provided by lift contractor. bell.

23. Scaffolding : To be provided by lift contractor. 24. M.S. Sill angles and facia plates : Included. 25. Steel for lift machinery : Included. 26. Servicing and maintenance : Free comprehensive Servicing and maintenance during the guarantee period of one year. 28. Special Feature: (a). “UP and DOWn arrows in landings only. (b). Steel Cubical for Controller. (c). M.S. Door frames for Landing Entrance. 29. Supply of Operation and Maintenance manual with necessary tools for operation. The list of Tools should be furnished by the contractor in a separate sheet duly signed. 30. Other Standard Features: Phase failure and phase reversal relay, T-guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity single reduction warm gear, electro mechanic brake with compression springs with car safety gear, buffer machanical door locks, emergency key, side supporting angles motor over load protection devices. Final limt switch.

Supply and clamping of 3½ X 35 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3½ X 35 sq.mm PVC Armoured LTUG Cable with earth connection.

Supply and providing cable end termination of 3½ X 35 sq.mm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and installation of air termination rod of 2mtr length of material AlMgSi of diametre ø 16/10 mm crimped on both the ends (Tappered Type). The rod shall be mounted with stainless steel clamp and fixing accessories. It should satiesfies IEC 62561-1 & 2 and it should Withstand Minimum wind velocity of 150m/s.

Supply and clamping of 8mm dia Aluminium alloy Solid Round Conductor of material AlMgSi used as down conductor system with necessary Conductor Holder,glue, connectors, joints and expansion piece etc as per IEC 62561-2 recommendation and site condition

Supply of Maintenance Free Copper bonded Earth rod of 3000mm length having the dia of 17.2 mm with copper coating thickness of 254 microns. The rod has been tested for Dimension, Marking, Tensile Strength, Salt mist, coating thickness, Electrical resistivity test before and after corrosion test as per IEC 62561-2.

Supply and installation of stainless steel SS 304 Grade Test Joint for fixing the 8-10 mm dia round conductor on the wall Test Parameter: a. Mechanical Load b. Environmental Test Should be Tested as per IEC 62561-4

Supply and run of Rust resistant non corossive 10 mm dia Copper Bonded Steel round conductor used for Earth termination inside the concrete and soil with necessary masonary and excavation work

Supply and installation of stainless steel SS 304 Grade conductor Holder for fixing the 8-10 mm dia round conductor on the wall Test Parameter: a. Mechanical Load b. Environmental Test Should be Tested as per IEC 62561-4

Supply and insallation Cabinet Type Class 1 and 2 Combined Model SPD in 4P enclosure box to arrest surges and overvoltages in the power linedue to lighning switching action etc. they must be installed in the incoming MCC panel / DB of the respective buling in parallel to the power circuit by using 4 of 6 Sqmm Cu(84 / 0.3) .Model: PSV4-12.5/400TT (3 phase power network)

Supply, erection testing, commissioning and handing over of 1No,250KVA diesel generator set with AMF panel 0.80 P.F, 3phase, 415v/420 Volts, 50c/s, 1500 RPM complete in all respects conforming to CPCB 1V PLUS Norms and BIS Specifications as detailed below A.Engine Air Cooled diesel engine suitable for generator application with a shaft out put of suitable at 1500 RPM under NTP conditions as per BS 5514-ISO 10002. The engine shall comprise the following standard scope of supply: (Make Kirloskar/ Cummins/ Ashok Leyland/ Greaves/ Equivalent) 1) Dry type Air cleaner 2) Expansion bellow 3) Radiator, radiator fan and mounting 4) Air to air charge cooler 5) Exhaust gas turbo charger 6) Lube oil cooler and lube oil filter filter 7) Fuel filter (pre and micro) 8) In-line mono-block fuel injection pump with governor and fuel feed pump 9) Electronic governor 10) 12V / 24V battery charging alternator 11) 12V / 24V Volt electric starter motor 12) Engine test certificate 13) Residential Mufler 14) Fly wheel with starter ring. Engine instrument panel/mounted Engine control panel consisting of ON/OFF/START/KEY, lube oil pressure gauge, oil temperature gauge, high water temperature gauge and electronic hour meter and RPM indicator. Safety system of Engine:

26) 1set pilot lamps of 3Nos 27) MCCB of 100A capacity with magnetic thermal over load release, instant start circuit trip and under voltage release switch. 28) Rectangular copper bus bars (1No for each phase, neutral and earthing terminal) of adequate capacity duly colour coded with head shrinkable PVC sleeves. 29) 1No mains voltage monitor 30) Hooter/Audio alarm for indication set fails to start and for DG O/L 31) 1set timers 32) Audio and visual indication arrangements for a) Low lubricating oil pressure b) High water temperature c) Over speed 33) 1No Earth fault relay 34) Isolator to Isolate the neutral Note: 1. The control panel should be complete with necessary fuses, cables, labels, other accessories with neutral isolation arrangements. 2. The engine should trip for the following conditions. a) Low lubricating oil pressure b) High water temperature c) Over speed 4) ACOUSTIC ENCLOSURE:

Acoustic enclosure shall be powder coated and fabricated of 16SWG CRCA MS sheet. The silent canopy shall be nut bolt type construction. Critical processes of punching are done on CNC machine to maintain dimensional accuracy of hole within 0.1mm power coating done after seven-tank surface preparation process of sheet metal. Canopy panel and door shall have inside lining of FIRE-RETARDANT 64kg/m density mineral wool of 100mm thickness as acoustic material. Four hinged doors shall be provided to canopy. The maximum permissble sound pressue level should be as per the norms prescribed by the Central Pollution Control Board / State Pollution Control Board/ Competent Authority concerened or shouble be 75 db(A) at 1 meter from the enclosure surface whichever is advantageous to the department. The emergency stop should be available on the enclosure panel. The enclosure provided shall be duly approved by the Engine Manufacturer of the Engine provided for Diesel Generator Sets mounted inside and should be to the satisfaction of inspection / testing authority concern. SURFACE TREATMENT – PAINTING The enclosure shall be suitably treated for degreasing, de-rusting and phospating. The canopies are passed through seven-tank treatment thoroughly. ADDITIONAL FEATURES OF CANOPIES Canopy fabricated on CNC machines with dimensional accuracy of 0.1mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if any.

WORLD CLASS COOLING PACKAGE: Canopies shall have cooling package for which it can perform at 45 deg c/ambient temperature. No grounding required on the ground, only a level surface capable of with standing the DG weight. Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. The Gen set frame shall also be provided with hooks for unloading. Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well with in 5-7 deg centigrade. 5) Base Frame Base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall have provision for mounting of acoustic enclosure on it. The supply of Gen set includes loading, unloading and transportation charges. 6) Fuel Tank 600 Ltrs. Removable Fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet an outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for cleaning or any maintenance.. 7) Battery 24V battery

Exhaust Piping DG Set should be offered complete with exhaust piping, ie, silence is mounted tnd connected by means of MS pipe through flexible pipe to the engine manifold. Entire exhaust piping inside the conopy (Cold Zone) is insulated by means of ceramic wool and aluminium gladded.

Providing suitable concrete foundation with cement concrete 1: 2:4 with sand cushion all around the the foundation erection of 250 Kva Generator set over the foundation and erection of Generator set with proper alignment of suitable size

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/supports on wall / floor/ground for earth connection.

Providing fuel oil to run the set for 8 hours on load testing and commissioning using water rheostat or suitable leading element. First charging of fuel oil to full capacity and first charging of battery while handing over to dept.

Supply of tools like: 15" cutting plier- 1No Screw driver 9"X6" - 2 Nos DE spaners ( 6 Nos) - 1set Adjustable spanner - 1No 1/216 Hammer - 1 No Line tester - 1 No

Supply and fixing of 2m x1m rubber mat suitable for 11KV installation confirming to IS (5Nos.), Handgloves 11KV grade, 4Nos. of Fire buckets made out of 40 x 40 x 6mm MS angle and 2Nos. Of fire extinguisher- Co2, 4.5kg with necessary arrangements.

Preparation of Site plan,physical layout Electrical Schematic diagram (10 Sets) and getting drawing approval from CEIG preparation of completion report rectification report etc., arranging CEIG inspection and paying CEIG inspection fees and obtaining safety certificate from CEIG and provision of approved drawing with neat frame works and submission of safety certificate.

Supply and fixing of 400A Three phase 500V 4 Pole change over switch on suitable angle iron frame work with MS cable entry boxes with PWD earthing. (SD-654)

GST at 18%

P KALIKURICHI (BID ID -1379407)

Smart Infratech Developers (BID ID -1372665)