TOURIST INTERPRETATION CENTRE AT KANNUR

Amount

Ground Floor

2.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.2 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.Ordinary or hard rock

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.3.1 : Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

60.7.1 : DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.11.1 : Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.35 : Add for using extra cement in the items of design mix over and above the specified cement content therein

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

4.11 : Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

od121949/2024_2025 : Applying a coat of Inertol Poxitar Coal tar epoxy coating per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil

2.35.1.1 : Diluting and injecting chemical emulsion for POST -CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion):Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete:With Chlorpyriphos /Lindane E.C. 20% with 1% concentration

14.91.1 : Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with nonwoven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25 degree, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23 degree as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150 degree. Cold flexibility shall be upto -2degree when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :3 mm thick

14.92 : Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

22.4.1 : Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Serrated with central bulb ( 225 mm wide, 8-11 mm thick)

50.6.7.1 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.

50.6.3.1 : Solid block masonry using pre cast solid blocks ( Factory made) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth for 10 cm thick wall in CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding etc complete

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

50.6.1.8 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand etc complete

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

od121952/2024_2025 : Providing and fixing fibre glass mesh of 145 GSM including cost and conveyance of all material and labour charge etc. complete

50.13.1 : 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

5.30 : Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

od121958/2024_2025 : Providing water cutting to bottom edge side of slab/sunshade by 25mm wide and 15mm thick in cement mortar 1:3 including cost and conveyance of all materials, labour charges etc complete

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

9.5.1.1 : Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge.Second class teak woodProviding and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick shutters

9.7.1 : Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Second class teak wood

od121959/2024_2025 : Preparation of wood surface for melamine polish: Preparation of wood surface for polishing as per the follwoing procedure: Filling the holes and screw marks in the wood surface using Wud filler and sandering the surface using 80 grade paper. Applying First coat Sanding Sealer. Fillig the Joints using Filler Powder and sandering with 120 grade paper.Applying second coat Sanding Sealer and sandering with 220 grade paper. Applying One coat melamine sealer and sandering with 320 grade paper

13.114 : Melamine polishing on wood work (one or more coat).

9.74.3 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:150x10 mm

9.74.4 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:100x10 mm

9.76 : Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.82 : Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

9.143 : Providing and fixing factory made uPVC door frame, made of uPVC extruded section, of size 65 mm x 55 mm with wall thickness 2.0 mm (? 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm ( ? 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

9.144 : Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm ( ± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (± 02. mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer -in- charge.

9.147D.3 : Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

od121968/2024_2025 : Providing and Fixing 1.25mm CR perforated rolling shutter ( 1m perforation) of specified size (as per drawing) including all cost of material and labour charges etc. complete. Size 2700x2800 mm

11.41.3 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x 800 mm

11.46.3 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 800 x 800 mm

11.48.3 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 800x800mm

11.50 : Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles

11.37 : Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

8.31 : Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

od121972/2024_2025 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 300x300 mm

od121973/2024_2025 : OD Providing PVC Tile beading in the edges and corners of tile work including cost conveyance labour charges etc complete.<br>

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.5 : Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

od121978/2024_2025 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 2400x800 mm

od121979/2024_2025 : Modified 11.47.4 - Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with Myk Laticrete335/ equivalent, including grouting of joints (Payment for grouting of joints to be made separately).

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

10.26.1 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

od121980/2024_2025 : Providing and fixing handrails with teak wood top rail of diameter 7cm including labour charges, material etc. complete

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

od121988/2024_2025 : Finishing with Polyurethane paint (Two Coats) at all locations prepared and applied as per manufacturer's specifications including epoxy based primer (One Coat), Manual preparation of surface including wire brush and papering, etc. complete. On Steel works.<br>

od121989/2024_2025 : Providing cement mortar reaper of 1:3 mix for supporting roofing tiles over sunshade, roofing slab etc including cost and conveyance of all labour charge, material etc complete. 50mmx25mm

od121990/2024_2025 : Modified12.48 Providing & fixing on roof ceramic tile of approved size and as per approved pattern on steel frame work complete(steel frame work to be paid seperately)

od121991/2024_2025 : <br>Modified 12.49 Providing & fixing on roof ceramic ridge tile of approved pattern on steel frmane work complete(steel frame work to be paid seperately)<br>

First Floor

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.35 : Add for using extra cement in the items of design mix over and above the specified cement content therein

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

od121952/2024_2025 : Providing and fixing fibre glass mesh of 145 GSM including cost and conveyance of all material and labour charge etc. complete

50.13.1 : 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

5.30 : Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

od121958/2024_2025 : Providing water cutting to bottom edge side of slab/sunshade by 25mm wide and 15mm thick in cement mortar 1:3 including cost and conveyance of all materials, labour charges etc complete

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

22.23.1 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @0.70 kg per sqm

22.23.2 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.

4.2.2 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:11/2:3 (1 cement : 11/2 coarse sand :3 graded stone aggregate 20 mm nominal size)

od122005/2024_2025 : Supplying and filling with cinder under , ramming consolidating and dressing complete. including all cost of materials, labour charges etc complete

9.143 : Providing and fixing factory made uPVC door frame, made of uPVC extruded section, of size 65 mm x 55 mm with wall thickness 2.0 mm (? 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm ( ? 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

9.144 : Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm ( ± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (± 02. mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer -in- charge.

10.5.1 : Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces

10.31 : Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer In charge.

od122021/2024_2025 : Supplying Stainless steel Padlock and Keys

9.62.1 : Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete:300x16 mm

9.63.4 : Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete:100x10 mm

9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

9.5.1.1 : Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge.Second class teak woodProviding and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick shutters

9.7.1 : Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Second class teak wood

od121959/2024_2025 : Preparation of wood surface for melamine polish: Preparation of wood surface for polishing as per the follwoing procedure: Filling the holes and screw marks in the wood surface using Wud filler and sandering the surface using 80 grade paper. Applying First coat Sanding Sealer. Fillig the Joints using Filler Powder and sandering with 120 grade paper.Applying second coat Sanding Sealer and sandering with 220 grade paper. Applying One coat melamine sealer and sandering with 320 grade paper

13.114 : Melamine polishing on wood work (one or more coat).

9.74.3 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:150x10 mm

9.74.4 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:100x10 mm

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.147D.3 : Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

9.48.1 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

11.41.3 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x 800 mm

11.46.3 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 800 x 800 mm

11.48.3 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 800x800mm

11.37 : Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

8.31 : Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

4.2.3 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

10.26.1 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

UG Tank

2.28.1 : Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

2.9.1 : Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Ordinary rock

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.2 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.Ordinary or hard rock

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.35 : Add for using extra cement in the items of design mix over and above the specified cement content therein

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

22.23.2 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.

22.23.1 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @0.70 kg per sqm

22.4.1 : Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Serrated with central bulb ( 225 mm wide, 8-11 mm thick)

od122034/2024_2025 : Supplying and fixing Ductile iron heavy duty(62kg) manhole covers of size 600x600mm

Septic Tank and Soak Pit

2.9.1 : Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Ordinary rock

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.35 : Add for using extra cement in the items of design mix over and above the specified cement content therein

50.6.7.1 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

22.23.1 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @0.70 kg per sqm

22.23.2 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.

22.4.1 : Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Serrated with central bulb ( 225 mm wide, 8-11 mm thick)

od122061/2024_2025 : Supplying and fixing Ductile iron heavy duty(62kg) manhole covers of size 600x600mm

Demolishing Works

15.9.2 : Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

15.2.2 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:4:8 leaner mix ( including equivalent design mix)

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.6 : Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B work.

15.5 : Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work ( Payment shall be made on the cross sectional area of R.C.C. or R.B work) as per direction of Engineer-in-charge.

15.7.4 : Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

15.12.2 : Of area beyond 3 sq. metres

16.83 : Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

15.28.2 : Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :Asbestos Sheet

15.18 : Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates,boltd, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

15.60 : Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

DG Foundation

2.28.1 : Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.6.7.1 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.

50.13.1 : 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

Sewage and Drain System- Internal and External

50.18.8.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.7.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

50.18.8.8.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.8.9.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.7.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

50.18.9.17.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

50.18.9.18.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

50.18.9.19.2 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 m dia 4 Kgf/cm2 - External work - Exposed on wall

50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.10.1 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

od122337/2024_2025 : Providing , fixing , testing and commissioning pvc multy inlet (110x75x50x50x50) floor trap of self cleansing design with or without vent arm complete, including cost of masonry or concrete supports cutting and making good the walls and floors where ever required

od122338/2024_2025 : Providing , fixing , testing and commissioning pvc "P" trap with multy inlet or single inlet connection of required sizes of self cleansing design with or without vent arm complete, including cost of masonry or concrete supports cutting and making good the walls and floors where ever required

od122400/2024_2025 : Providing and fixing PVC Adapter Boss of approved quality 110 x 50 mm

od122401/2024_2025 : Providing and fixing PVC Adapter Boss of approved quality 110 x 63 mm

od122402/2024_2025 : Providing and fixing two piece CP , air tight floor clean out plug of approved quality . l25mm square frame with 100 mm dia openable circular lid

od122403/2024_2025 : Providing, fixing, testing and commissioning at site C.P. or stainless steel Grating Cover with protection from cockroaches of matching size of multi inlet or "P" trap complete in all respects. 5“ Frame with 4" Openable Lid/Grating

od122404/2024_2025 : Providing and fixing GI slotted rail of approved design. projecting 75 mm outside the wall surface and fixed on wall with 2 nos, 6/8 mm dia expansion hold fasteners, including drilling necessary holes in brick wall / CC / RCC surface and the cost of bolts included. The pipes shall be fixed to the already fixed brackets with the help of 8 mm galvanised GI "U" bolts of specified shape and shall be fixed with GI nuts, bolts, & washers of suitable size, one bolts on each side of the pipe

od128637/2024_2025 : Supply and fixing of 600x600mm DI MD manhole cover of approved quality

19.4.2.1 : 150x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

od122412/2024_2025 : Providing and fixing Rain water Khurrah of approved quality Make : Floortech/Equivalent

50.18.9.20.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow

50.18.9.20.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

50.18.9.20.2 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow

50.18.9.20.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia vent cowl

50.18.9.20.9 : Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC solvent cement-63 mm dia Socket /coupling

50.18.9.22.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.2 : Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

Internal Water Supply

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.8.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal outer dia pipes

18.7.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal outer dia pipes

18.7.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes

18.7.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes

18.7.5 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall40 mm nominal outer dia pipes

18.7.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal outer dia pipes

18.9.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work20 mm nominal outer dia pipes

18.9.5 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work40 mm nominal outer dia pipes

18.9.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work50 mm nominal outer dia pipes

18.18.2 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:20 mm nominal bore

18.18.3 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore

18.19.2.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):32 mm nominal boreHorizontal

18.19.3.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):40 mm nominal boreHorizontal

18.19.4.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):50 mm nominal boreHorizontal

CP and Sanitary Fixtures

17.2.1 : Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

50.17.1.5 : Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

17.10.1.2 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x 1040 mm bowl depth 225 mm

od126814/2024_2025 : Providing and fixing of sink cock with wall flange of approved quality Make: Jaquar/Hindware/Parryware/Equivalent

od126815/2024_2025 : Supplying, fixing & testing of Concealed Stop Cock with Over Head Shower including all accessories ,cutting and making good the walls wherever required Make : Jaquar/Hindware/Parryware/Equivalent

17.7.2 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap

18.74.2 : Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, Collar and bush approved quality and colour .15 mm nominal bore with 45 cm length

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

17.73.2 : Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighting not less than 190 gms

17.23 : Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

od122509/2024_2025 : Supplying and Fixing of C.P. Urinal push cock of approved quality. Make : Jaquar/Hindware/Parryware/Equivalent

od122510/2024_2025 : Supplying and Fixing of Urinal Partition of approved quality. Make : Jaquar/Hindware/Parryware/Equivalent

od122511/2024_2025 : Supplying and Fixing CP Robe Hook of approved Quality Make : Jaquar/Hindware/Parryware/Equivalent

od122512/2024_2025 : Supplying and Fixing CP Towel Ring fixed with SS screws on to the toilet. Make : Jaquar/Hindware/Parryware/Equivalent

od122513/2024_2025 : Supplying and Fixing CP Soap Dish of approved Quality Make : Jaquar/Hindware/Parryware/Equivalent

od122514/2024_2025 : Providing and fixing of soap dispenser of approved quality Make : Jaquar/Hindware/Parryware/Equivalent

od122515/2024_2025 : Supplying & fixing of 4 nos of Grab bar and 1 no of Folding type Grab bar with necessary fittings at both side of commode for physically challend persons all complete as directed. Make : Jaquar/Hindware/Parryware/Equivalent

Electrification Works

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.55.2 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B

1.55.3 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.11 : Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.17.3 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.17.30 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 6 sq. mm

1.17.14 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.5 x 2.5 sq. mm

1.17.23 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.5 x 4 sq. mm

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.24.7 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

90.10.3.15 : Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )

od122524/2024_2025 : Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant ) 20A DP switch with indicator

90.10.3.33 : Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

90.10.1.3 : Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )

90.10.1.4 : Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )

90.10.1.5 : Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )

1.28.2 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

1.28.3 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.4 Module

1.28.4 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.6 Module

1.33 : Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.58 : Supplying and fixing PVC batten/ angle holder including connection etc. as required.

od122527/2024_2025 : Supply, Fixing, testing and commissioning of 6 module matt aluminium finish pop up box with slim design for perfect integration into furniture equipped with two number 6A socket and 6A Switch supplied along with installation kits for table tops and all accessories as required for complete installation, providing connections etc as required. Make: Legrand or equivalent.

od122528/2024_2025 : Supply, Fixing, testing and commissioning of 3 module matt aluminium finish pop up box with slim design for perfect integration into furniture equipped with one number 6A socket and 6A Switch supplied along with installation kits for table tops and all accessories as required for complete installation, providing connections etc as required. Make: Legrand or equivalent.

2.3.3 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator12 way, Double door

2.3.4 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator16 way, Double door

2.4.1 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door

2.4.2 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door

90.11.1.19 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.3 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

od122607/2024_2025 : Supplying and fixing 40A to 63A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.<br>Single pole

od122611/2024_2025 : Supplying and fixing 40A to 63A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.<br>Triple pole

od122608/2024_2025 : Supplying and fixing 6A to 32A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.<br>Four pole

od122609/2024_2025 : Supplying and fixing 40A to 63A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.<br>Four pole

2.12.1 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.14.2 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.1 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

od122692/2024_2025 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A

od122693/2024_2025 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

90.14.10.3 : Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.

2.11 : Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

od122697/2024_2025 : Supply, installation, testing and commissioning of thermoplastic polycarbonate enclosure (IP65) of size 126x228x111mm on surface/ recess for fixing MCB/RCCB/Isolator/Surface box, complete with connections, testing and commissioning etc. as required.Make: Hensel or equivalent.1row 4 module

od122698/2024_2025 : Supply, installation, testing and commissioning of thermoplastic polycarbonate enclosure (IP65) of size 102x197x92mm on surface/ recess for fixing MCB/RCCB/Isolator/Surface box, complete with connections, testing and commissioning etc. as required.Make: Hensel or equivalent.1row 3 module

5.4 : Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

90.4.5.2 : Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required.

90.16.1.3 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required

od122704/2024_2025 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables, through wall/existing trench and giving connection as required. 25 x 3 mm Cu strip

90.16.5.3 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.

od125609/2024_2025 : Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required. 3.5C 70 sqmm XLPE Al

od125610/2024_2025 : Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required. 3.5C 50 sqmm XLPE Al

od125611/2024_2025 : Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required. 3.5C 35 sqmm XLPE Al

od125612/2024_2025 : Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required. 4C 16 sqmm XLPE Al

od125615/2024_2025 : Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required. 4C 10 sqmm XLPE Al

od125616/2024_2025 : Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required. 3C 1.5 sqmm Cu armoured cable

od125617/2024_2025 : Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required. 2C 10 sqmm XLPE Al

7.5.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

7.5.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 35 sq. mm and upto 95 sq. mm

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.7.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.8.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

90.12.10.2 : Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation

9.1.21 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.22 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.2 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 10 sq. mm (19mm)

od125625/2024_2025 : Supply and fixing of thermoplastic polycarbonate cable junction box IP66/67 in accordance with IEC60529 environment friendly, recyclable, UV resistant, halogen & silicon free, anti acid & anti corrosive, shockproof with 5 pole terminals suitable to terminate upto 2.5sqmm

od125626/2024_2025 : Supply and fixing (IP68) thermoplastic polyamide cable gland with appropriate size lock nut suitable for 3core 1.5/2.5 sq mm armoured copper cable including all accessories as required

4.6.1 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.100 mm width X 50 mm depth X 1.6 mm thickness Details of cost for 30 metres

4.6.2 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.6.4 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm width X 50 mm depth X 1.6 mm thickness

1.41 : Installation, testing and commissioning of pre - wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

90.4.3 : Conveyance installation testing and commissioning ceiling fan of all sizes using standard accessories excluding resistance type regulator wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or extending the original wiring etc. as required.

1.47 : Supplying and fixing extra down rod of 10 cm length G.I. pipe, 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

90.4.1 : Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

1.50.1 : Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

90.4.8 : Charges for cutting holes suitable for accommodating exhaust fans up to 305mm sweep including plastering colour washing etc. as required.

90.4.9 : Charges for cutting holes suitable for accommodating exhaust fans above 305mm sweep and up to 450mm sweep including plastering colour washing etc. as required.

90.4.6 : Conveyance, installation, testing and commissioning of wall mounting fans of all types using mounting brackets supplied along with the fan.

od125642/2024_2025 : Supply of 20+5W LED tube light fitting housing made of Extruded thermal polycarbonate with 6500K colour temperature with duly wired up for use on 230 V AC. The fittings shall be directly on ceiling/ wall, including all accessories etc. as required. Make Jaquar or equivalent

od125643/2024_2025 : Supply of 6.5+2W surface/wall mounted LED bulkhead light fixture (IP 65) housing made of pressure die cast aluminium, 4000-6500K colour temperature with a lumen output minimum l00lumen/Watt suitable for outdoor applications, including all connections etc. as required. Make - Philips or equivalent

od125644/2024_2025 : Supply of 10+2W surface/wall mounted LED tube light fixture -2 feet have polycarbonate housing, 6500K colour temperature, with minimum 100 lumen/Watt, working on 240V AC, suitable for indoor applications, including all connections etc as required. Make - Wipro or equivalent

od125645/2024_2025 : Supply of 34+2W LED tube light fitting housing made of Extruded thermal polycarbonate with 6500K colour temperature with duly wired up for use on 230 V AC. The fittings shall be directly on ceiling/ wall, including all accessories etc. as required. Make: Philips or equivalent

od125646/2024_2025 : Supply of 15+2W suspended LED down light fixture, housing made of pressure die cast aluminium, with 5700K colour temperature, with a lumen output minimum 1001umen/Watt suitable for indoor applications, including all connections etc. as required. Make - Wipro or equivalent

od125647/2024_2025 : Supply of 15+2W surface mounted round LED down light fixture housing made of pressure die cast aluminium, with 5700K colour temperature, with a lumen output minimum 100lumen/Watt suitable for indoor applications, including all connections etc. as required. Make - Wipro or equivalent

od125648/2024_2025 : Supply, installation, testing and commissioning of 8W LED spike light fixture, 3000K colour temperature, IP65 including all connections etc. as required. Make -Jaquar or equivalent

od125649/2024_2025 : Supply of 15+2W surface mounted square LED down light fixture housing made of pressure die cast aluminium with 6500K colour temperature, with a lumen output minimum 100lumen/Watt suitable for indoor applications, including all connections etc. as required. Make - Philips or equivalent

od125650/2024_2025 : Supply of 6W surface mounted squar LED down light fixture housing made of pressure die cast aluminium, with 6500K colour temperature, with a lumen output minimum l00lumen/Watt suitable for indoor applications, including all connections etc. as required. Make - Philips or equivalent

od125651/2024_2025 : Supply of 30+ 2W LED linear surface mounted light fixture, housing made of Extruded aluminium, with 4000K colour temperature, and having minimum 100 lumen/Watt, suitable for indoor applications, including all connections etc. as required. Make -Wipro Lineos or equivalent

od125652/2024_2025 : Supply and fixing of 9+/-2W LED bulb in the existing fitting, including all connections etc as required. Make - Philips or equivalent

od125653/2024_2025 : Supply of following Exhaust fan in plastic frame working on 230 V AC including giving connection etc. as required. 250mm light duty exhaust fan. Make - Havells or equivalent

od125654/2024_2025 : Supply of 400mm sweep Wall fan working on 230 V AC. The work shall include fixing necessary bolt and nuts making good the damages etc. as required. Make - Hazells or equivalent

od125655/2024_2025 : Supply of following Exhaust fan in metal frame working on 230 V AC including giving connection etc. as required. 380mm heavy duty exhaust fan. Make - Hazells or equivalent

od123263/2024_2025 : MSB Incomer 1 : 125A 4P MCCB 25kA TM-lNo, Meters and indication lamps: RYB indication with control fuses-1 Set, MFM showing V,A,F,PF etc. with control fuses and CTs -1 Set, 125A FP Contactor-lNo Incomer 2 : 100A 4P MCCB 25kA TM-lNo, Meters and indication lamps: RYB indication with control fuses-1 Set, MFM showing V,A,F,PF etc. with control fuses and CTs -1 Set, Reverse power relay with control CT-lNo, 125A FP Contactor-lNo AMF with Mechnical and Electrical interlock-lNo Busbar: Aluminium busbar suitable for 125A Outgoings: 63A TPN TM MCCB 16kA - 4 Nos, 63A TPN TM MCCB 16kA with shunt trip facility - lNo, 40A TPN TM MCCB 16kA - 1 No, 40A FP Isolator - 1 No

od123264/2024_2025 : Lift Panel Incomer: 40A FP Swicth Disconnector -lNo, Meters and indication lamps: RYB indication with control fuses-1 Set, MFM showing with control fuses and CTs -1 Set, Busbar: Aluminium busbar suitable for 40A Outgoings: 63A FP RCBO100mA -1 No, 25A DP RCBO 30mA- lNo, 6A SP MCB 10kA - 2Nos

od123265/2024_2025 : UPS Panel Incomer: 40A FP Isolator-lNo, Busbar: Aluminium busbar suitable for 40A Outgoings: 25A SP MCB 10kA - 4Nos

od123266/2024_2025 : Installation, testing and commissioning of Metering Panel including all connections etc. as required

od123267/2024_2025 : Installation, testing and commissioning of MSB including all connections etc. as required

od123268/2024_2025 : Installation, testing and commissioning of Lift panel including all connections etc. as required

od123269/2024_2025 : Installation, testing and commissioning of UPS panel including all connections etc. as required.

od127337/2024_2025 : Supply of cubicle construction made out of 2mm thick CRCA sheet for enclosure and 1.6mm thich CRCA sheet for partitions, totally enclosed, free standing, wall/floor mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system with busbars extendable on both sides, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene gasket etc. including fixing it and making good the damages colour washing etc. as required. Comprising the following: (Specification as per the submitted schematic drawing, any changes as per the recommendations from KSEBL/ Electrical inspectorate will be charged extra ) Metering Panel Incomer: 125A Cut Out Fuse, Provision for fixing LT TOD meter with control CTs. Outgoings: 125A FP TM MCCB 25kA - 1 No.

od127338/2024_2025 : Supply, installation, testing and commissioning of 6 kVA, single phase input, single phase output UPS system along with necessary 12V SMF batteries for 30 minutes back up and powder coated rack including all accessories, cabling etc. as required (Make: Socomec or equivalent)

od127339/2024_2025 : Supply, erection, commissioning of 3" dia additional length of exhaust pipes with necessary bends, clamps etc from residential silencer as required

od127340/2024_2025 : Supplying and providing thermal insulation with aluminium cladding to 3" dia exhaust pipe as required

od127341/2024_2025 : Supply and installation of 12V battery charger for the existing DG set

od127342/2024_2025 : Supply and fixing framed shock treatment chart as required

od127343/2024_2025 : Supply and laying 2.50 mm thick, 11 kV, Synthetic elastromeric fire retardant insulating sheet as required

2.21 : Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

od123195/2024_2025 : Supply, Installation Testing and commissioning of 10 Passenger Machine Room less Lift with the following specifications including all required standard Features.1. Type of Lift: Passenger lift(10 passenger) 2. Method of control Micro processor based V3F with ARD system. 3. Load/Person: 680kg/10 persons 4. Rated Speed in mls: 1.00 mls 5. Car Travel: 6.6 m approx 6. No. of Floors Served: Three 7. Overhead: 4000mm 8. Pit height: l500mm 9. Operation: Simplex Full Collective Control 10. Hoist way Required: l800mm wide x 2400mm deep 11. Hoist way Entrance: Two panel to left opening plain Panel 12. Car dimensions: As per OEM standard 13. Door dimensions: 900 mm wide x 2000 mm internal height 12. Power supply: 4 l5volts, 3 phase, 50Hz, AC regulation 340-480 V 13. Car Ceiling and Lighting: Direct lighting, round/square LED (CL60) Stainless Steel Round/Square spot LED light 14. Car flooring: Stainless steel 6 mm anti skid flooring: Stainless steel Hairline. 15. Car operating panel: Full Height Stainless Steel Face Plate Silver brushed Segmented LCD display Square flush mounted & Automatic Rescue Device Provide automatic rescue device with an electronic controller powered by 4 Nos. 12V 24 AH dry sealed maintenance free batteries. The rescue operation should act within 10 seconds of power failure 16. Landing Signalization-Stainless Steel 7 segment display Flush Mounted Silver brushed Square

Heating, Ventilation and Air Conditioning Works

od123519/2024_2025 : Supply, installation, testing and commissioning of Non-Inverter Wall mounted/High wall type Split AC unit complete with indoor unit and outdoor unit. Indoor unit with DX cooling coil,filter,fan-motor assembly and air outlet with horzontal/vertical automatic rotating deflecters.Air cooled condensing unit complete with Scroll/Rotary compressor, condenser fans,condenser coil.The unit should operate on R4l0A/R32/R407C refrigerant.Rates shall include cordless remote controller. Make:Daikin/Carrier/Equivalent 1.5 TR High wall unit

od123520/2024_2025 : Supply, installation, testing and commissioning of Non-Inverter Wall mounted/High wall type Split AC unit complete with indoor unit and outdoor unit. Indoor unit with DX cooling coil,filter,fan-motor assembly and air outlet with horzontal/vertical automatic rotating deflecters.Air cooled condensing unit complete with Scroll/Rotary compressor, condenser fans,condenser coil.The unit should operate on R4l0A/R32/R407C refrigerant.Rates shall include cordless remote controller. Make:Daikin/Carrier/Equivalent 2.0 TR High wall unit

od123521/2024_2025 : Supply, installation, testing and commissioning of Non-Inverter ceiling mounted four way cassette type Split AC unit complete with indoor unit and outdoor units. Indoor unit with DX cooling coil, filter, fan-motor assembly and inbuilt drain pump. Air cooled condensing unit complete with Scroll/Rotary compressor,condenser fans,condenser coil. The unit should operate on R22/R410A/R32 refrigerant.Rates shall include cordless remote controller. Make:Daikin/Carrier/Equivalent 4.0 TR Cassette unit

od123522/2024_2025 : Supply, installation, testing and commissioning of Non-Inverter ceiling mounted Ductable type Split AC unit complete with indoor unit and outdoor units. Indoor unit with DX cooling coil ,filter and fan-motor assembly. Air cooled condensing unit complete with Scroll/Rotary compressor,condenser fans,condenser coil.The unit should operate on R410A/R32/R22 refrigerant.Rates shall include corded remote controller. Make:Daikin/Carrier/Equivalent 8.5 TR Ductable unit

od123523/2024_2025 : Supply, installation, testing and commissioning of seamless half hard temper copper refrigerant piping with necessary fittings like Elbows,Tees, Reducers, Couplers etc. Regrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in confrormnace with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods,anchor bolt,threaded fastners and supports. Make: Mandev/Totaline/Equivalent. 28.6 mm

od123524/2024_2025 : Supply, installation, testing and commissioning of seamless half hard temper copper refrigerant piping with necessary fittings like Elbows,Tees, Reducers, Couplers etc. Regrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in confrormnace with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods,anchor bolt,threaded fastners and supports. Make: Mandev/Totaline/Equivalent. 25.4 mm

od123525/2024_2025 : Supply, installation, testing and commissioning of seamless half hard temper copper refrigerant piping with necessary fittings like Elbows,Tees, Reducers, Couplers etc. Regrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in confrormnace with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods,anchor bolt,threaded fastners and supports. Make: Mandev/Totaline/Equivalent. 22.2 mm

od123526/2024_2025 : Supply, installation, testing and commissioning of seamless half hard temper copper refrigerant piping with necessary fittings like Elbows,Tees, Reducers, Couplers etc. Regrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in confrormnace with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods,anchor bolt,threaded fastners and supports. Make: Mandev/Totaline/Equivalent. 19.1 mm

od123527/2024_2025 : Supply, installation, testing and commissioning of seamless half hard temper copper refrigerant piping with necessary fittings like Elbows,Tees, Reducers, Couplers etc. Regrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in confrormnace with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods,anchor bolt,threaded fastners and supports. Make: Mandev/Totaline/Equivalent. 15.9 mm

od123528/2024_2025 : Supply, installation, testing and commissioning of seamless half hard temper copper refrigerant piping with necessary fittings like Elbows,Tees, Reducers, Couplers etc. Regrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in confrormnace with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods,anchor bolt,threaded fastners and supports. Make: Mandev/Totaline/Equivalent. 12.7 mm

od123529/2024_2025 : Supply, installation, testing and commissioning of seamless soft temper copper refrigerant piping with necessary fittings like Elbows,Tees, Reducers, Couplers etc. Regrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in confrormnace with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods,anchor bolt,threaded fastners and supports. Make: Mandev/Totaline/Equivalent. 15.9 mm

od128638/2024_2025 : Supply, installation, testing and commissioning of seamless soft temper copper refrigerant piping with necessary fittings like Elbows, Tees, Reducers, Couplers etc. Refrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in conformance with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods, anchor bolt, threaded fasteners and supports. Make: Mandev/Totaline/Equivalent. 12.7 mm

od123530/2024_2025 : Supply, installation, testing and commissioning of seamless soft temper copper refrigerant piping with necessary fittings like Elbows,Tees, Reducers, Couplers etc. Regrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in confrormnace with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods,anchor bolt,threaded fastners and supports. Make: Mandev/Totaline/Equivalent. 9.5 mm

od123531/2024_2025 : Supply, installation, testing and commissioning of seamless soft temper copper refrigerant piping with necessary fittings like Elbows,Tees, Reducers, Couplers etc. Regrigerant piping shall be of DHP grade, eddy current tested and RoHS compliant Refrigerant piping shall be duly insulated with nitrile rubber sleeves with all joints sealed with black adhesive tape in confrormnace with manufacturer recommendations. All refrigerant pipes shall be properly anchored to ceiling/wall using threaded rods,anchor bolt,threaded fastners and supports. Make: Mandev/Totaline/Equivalent. 6.4 mm

90.6.5.11 : Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.

90.6.5.18 : Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.

90.6.5.12 : Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.

90.6.5.14 : Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.

90.6.5.19 : Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.

90.6.5.21 : Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

od123532/2024_2025 : Supply and charging of Refrgerant gas in conformance with manufacturer recommendations.The refrigerant shall have low Global Warming Potential, low Ozone Depletion Potential , thermal stability to high temperature, compatible with lubricating oil, non-corrosive and non-flammable at ambient temperature and pressure. Make:DuPont/Value/Equivalent

od123533/2024_2025 : Supply and installation of buck down voltage stabilizer to maintain a constant voltage level for air conditioning units to prevent undue power failures. Make:V-Guard/Equivalent 4 KVA

od123534/2024_2025 : Supply and installation of buck down voltage stabilizer to maintain a constant voltage level for air conditioning units to prevent undue power failures. Make:V-Guard/Equivalent 5 KVA

od128688/2024_2025 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10Kgf/ cm2- Internal work- Exposed on wall

od128689/2024_2025 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall

od128690/2024_2025 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 10 Kgf/cm2- Internal work- exposed on wall

od123535/2024_2025 : Supply and installation of necessary mounting arrangements for High wall outdoor units with suitable vibration isolators. All frame supports shall be of Mild Steel

od123536/2024_2025 : Supply and installation of necessary mounting arrangements for Cassette outdoor units with suitable vibration isolators. All frame supports shall be of Mild Steel

od123537/2024_2025 : Supply and installation of necessary mounting arrangements for Ductable outdoor units with suitable vibration isolators. All frame supports shall be of Mild Steel

od123538/2024_2025 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.63 mm thick

od123541/2024_2025 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.80 mm thick

od123542/2024_2025 : Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.63 mm thick

od123543/2024_2025 : Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for<br>0.80 mm thick

od123544/2024_2025 : GI volume control duct damper Supply, installation, testing and commissioning of Gl volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. GI volume control duct damper

od123545/2024_2025 : Supply Air Grills Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications

od123546/2024_2025 : Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required. Return Air Grills

od123547/2024_2025 : Supply & installation, testing and balancing of collar damper Make:Airmaster/Systemair/Equivalent. Collar Damper

od123548/2024_2025 : Supply and fixing of class 'O' type closed cell elastomeric Nitrile rubber insulation of the following thickness for thermal insulation of ducts.The material should conform to Class 1 rating for surface spread of Flame. Make:Armaf1ex/Kf1ex/Equivalent. 9 mm thick Nitrile Rubber

od123549/2024_2025 : Supply and fixing of class '1 ' type open cell elastomeric Nitrile rubber insulation anti microbial type of the following thickness for acoustic insulation of ducts.The material should conform to Class 1 rating for surface spread of Flame. Make:Armaf1ex/Kf1ex/Equivalent. 10 mm thick Nitrile Rubber

od123550/2024_2025 : Supply and installation of fresh Air Inlet for Cassette indoor units connected by PVC pipes of specified thickness as required. Make:Supreme/Astral/Equivalent 75 mm dia - 4kgf/cm2

od123551/2024_2025 : Supply, installation, testing and commissioning of Butterfly damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc., as per specifications of following size Make: Airmaster/Systemair/Equivalent 100 mm Dia

od123552/2024_2025 : Supply and installation of powder coated aluminium air louvers with birdscreen as per the approved quality. Make: Airmaster/Systemair/Equivalent

od123553/2024_2025 : Supply and fixing of 5mil Fiber glass cloth over copper pipe for mechanical and UV protection. Fiber Glass cloth

od123554/2024_2025 : Supply and applying of vapour barrier coating 30 36 over the fiber glass cloth. Vapour Barrier coating

od123555/2024_2025 : Supply installation testing and commissioning of Inline fan for ventilation. Make:-Ostberg/Systemair/Caryaire/Equivalent 200 CFM 10mm ESP, Exhaust Fan

od123556/2024_2025 : Supply installation testing and commissioning of Inline fan for ventilation. Make:-Ostberg/Systemair/Caryaire/Equivalent 300 CFM 10mm ESP, Exhasut Fan

od123557/2024_2025 : Supply, installation, balancing and commissioning of Exhaust valves constructed from extruded aluminum with powder coated finish. Make:Airmaster/Systemair/Equivalent. 100mm dia

od123558/2024_2025 : Supply, installation, testing & commissioning of uninsulated semi rigid flexible duct of following size duly supported at regular interval as per site requirement etc.complete as required as per specifications. Note: Consider when the rigit duct connection is not possible. 100 mm Dia

od123559/2024_2025 : Supplying & installation of Condensate Drain pump kit for High wall units.The drain pump kit shall inlcude tank to collect condensate with inlulit filter and float switch to operate when near full, motor, non-return valve and drain connector kit. Note : If the slope is not available as per site condition, then only this component shall be operated. Make:Aspen/Microdam/ Equivalent

Networking and CCTV

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.28.1 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

1.53.1 : Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

90.10.1.2 : Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )

od124402/2024_2025 : Supply and laying of Outdoor Cat 6 UTP Cable through existing conduits

od124403/2024_2025 : Supply and installation of Information Outlet Category 6 RJ“5 Information Outlet with IDC Connector terminations

od124404/2024_2025 : Supply and installation of Cat 6 RJ 45 Connectors with boot

od124405/2024_2025 : Supply and installation of 1 Meter Cat 6 UTP Patch Cord

od124406/2024_2025 : Supply and installation of2 Meter Cat 6 UTP Patch Cord

od124407/2024_2025 : Supply and installation of Cat6 UTP , Patch Panel - 24 ports fully loaded patch panel with rear strain release bar

od128646/2024_2025 : Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including 3x3 or suitable size moulded plastic Camera Co box on surface

od124408/2024_2025 : Supply & Fixing the weatherproof Camera back box

od124409/2024_2025 : Supply and installation of 22U Network rack , 600 x 600mm with glass Door, Side Panels, 3 No of Horizontal shelfs, 4 No of Rack Air Circulation module, 2 No of Rack mountable Horizontal PDU with 6 Sockets 5A single phase supply, 5 No of Horizontal Cable Manager , Lock & Key and Mounting Accessories

od124410/2024_2025 : Supply and installation of Ethernet PoE Surge protection device for camera

od124411/2024_2025 : Supply & Fixing of the Weatherproof Junction of Box with necessary accessories for Pole mounting for placing the Surge Protection Devices

od124412/2024_2025 : Supply, installation, testing and commissioning of GI pole of 3.5m height, 3 inch Diameter, Class B, Fixed in concrete footing with properly finished with painting as required,Pole drilling for cable entry, Base plate etc.

od124413/2024_2025 : Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 em below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required. 40 mm Size

od124414/2024_2025 : Supply and installation of Layer 2 manageable Non PoE switch with Non blocking switch fabric having 24 Port 10/100/l000Mbps Non PoE & 2x1G SFP port. Three year warranty

od124415/2024_2025 : Supply and installation of Layer 2 manageable PoE switch with Non blocking switch fabric having 24 Port 10/100/l000Mbps PoE & 2x1G SFP port. Three year warranty

od124416/2024_2025 : Supply and installation of 4MP IP Dome Camera, 2.8mm or optional fixed lens , H.265 /H.264 encoding, Day/Night (ICR), l20Db WDR, IR LEDs Length 30m , Onvif, IP66 or Higher, PoE

od124417/2024_2025 : Supply and installation of 4MP IP Bullet Camera, 3.6mm or optional fixed lens , H.265 /H.264 encoding, Day/Night (ICR), l20WDR, IR LEDs Length 30m, Onvif, IP66 or Higher, PoE

od124418/2024_2025 : Supply and installation of 32 Channel NVR support upto 8MP at 320mbps or higher , Supports 4K,8 HDD SATA supports upto 8TB each , HDMI,VGA support, H264/H.265 Compression,Onvif profile.Three year warranty

od124419/2024_2025 : Supply and installation of 6 TB Surveillance hard disk for WD Purple surveillance storage is built to handle up to 64 cameras per drive and is designed for 24/7, always on, high-definition surveillance security systems with more than eight bays, With a wide range of industry-leading enclosures and chipsets supported, you're sure to find the configuration and compatibility that's right for your NVR

od124348/2024_2025 : Supply and installation of 32" HD LED monitor details of OEM 32" LED TV It's a 81.28 cm (32-inch), HD Ready (1366 x 768) panel, Reliable Sharp LED TVs are proven and tested based on IEC 60065 standard to adopt high temperature and humidity settings, tested with weight loading IEC 60065 standard, Varistor protects the product from lightning surge through AC cable that in line with EMC standard (IEC 61000-4-2 & IEC 61000-4-5), strict Japanese quality standard

od124349/2024_2025 : Supply and installation of 15 mtrs HDMI cable, audiovisual experience with our 15-meter HDMI to HDMI Cable 1.4V, designed to deliver impeccable 4K 2K quality. Ideal for long-distance connections in home theaters, conference rooms, and gaming setups. This high-speed HDMI cable ensures reliable performance and supports resolutions up to 3840x2160 at 30Hz, perfect for immersive viewing and smooth game play

od124350/2024_2025 : Supply and installation of the EPABX system of 16 analog extensions. Expandable,3 analog trunk, IP ready ISDN Comptable,lnbuilt VoIP, lightning protector for analog trunk lines, Port for Operator Console.Three year warranty

od124351/2024_2025 : Supply and installation of 24 key Console Hybrid Digital Telephone is elegantly designed and feature-packed digital phone, With 24 programmable feature buttons, the phone is easy and intuitive to use,flexibility and investment protection

od124352/2024_2025 : Supply and installation of CLI Phones,With features like Caller ID, intercom functionality, compatibility with EPABX systems, and both desk and wall mounting options, this phone is a versatile addition to any setup

od124353/2024_2025 : Supply and instalaltion of 25 Port Voice Panel, with features like 1U size 25 port Cat.3 ISDN patch panel, can be used in standard 19” cabinet, the cable manager is combined in this patch panel. All kinds of cables with different dimensions can be fixed on the patch panel, FCC port for RJ45 Cat.3 patch cord and IDC for horizontal distribution cables

od124354/2024_2025 : Supply of central hub with - PTZ camera with 12x optical Zoom, and Speakerphone including Simultaneous SDI, HDMI, USB, IP Outputs | NDI|HX Protocol; SDI, HDMI, USB Outputs | 12x Optical Zoom | RS-232, VISCA over IP Control, providing seamless connectivity to laptops/PCs via USB ports. With pan/tilt features, they offer expansive angle coverage. This camera delivers high-definition video quality, enabling real-time interactions with a powerful 12x optical zoom. An additional unique feature is the automatic brightness adjustment etc all complete

od124355/2024_2025 : Supply of USB group speakerphone with USB cable, this speakerphone can also be used in conjunction with VoIP softphone applications from Avaya, Cisco, Nortel, and Mirial virtually eliminating the need for a traditional, hard wired telephone. Inside the CHAT 150 you will find full duplex functionality providing a smooth transition between talking and listening, enhanced noise cancellation, and advanced audio level management. Once installed you can take advantage of three built-in microphones covering a distance of up to 8 feet in all directions. Additionally, volume up, volume down, and microphone mute buttons make it easy to adjust call volume while on a call

od124356/2024_2025 : Supply of 12' link cable with integrated power supply connection, power adapter and international power clips including CHATAttach Expansion Kit - Includes 12' link cable with integrated power supply connection, power adapter with international power clips, an additional power supply, cables and quick start guide

od124357/2024_2025 : Supply of USB 3.0 B to A USB cable 3 mts length, 3.0/3.1 specification does not specify a maximum cable length between USB 3.0/3.1 devices (SuperSpeed or SuperSpeed+), but there is a recommended length of 3 meters (or about 9 feet and 10 inches)

od124358/2024_2025 : Supply of USB 3.0 powered l0mts extender cable A male to A female With features USB Type: USB A-Male To USB A-Female, Mount Type: Panel Mount, USB V: USB 3.0, Data transfer rate: 5Gbps, Cable lead length: 0.5 Meter

od124359/2024_2025 : Supply of 65" LED display with wall mount With features, ARM Advance AI Quard Core A55 CPU, GPU Mali G31 MP2, 700MHz GPU, 1.5 GB RAM, 8 GB ROM, WEb OS, 3840 x 2160 Max. Resolution, 16:9 Aspect Ratio, 16.7 Millions Display Colors, 100-240V; 50/60HZ Power supply etc all

od124360/2024_2025 : Supply of HDMI Extender with features 50m HDMI Extender over single cat5e/6 cable with 38-56KHZ Bi-Directional IR. Novalink NX-LX21B TX & RX ₹4,200. Only RX ₹2,500

od124361/2024_2025 : HDMI Cable 6feet with Ethernet, 8k@60Hz, 4K@120Hz UHD Resolution, 48 GBPS Transmission Ultra High Speed, Dolby DTS, eARC, 3D,Male-to-Male,Compatible with All HDMI-Enabled Devices

od124362/2024_2025 : Installation charges for video conferencing

od124363/2024_2025 : Supply of 8" 2-way Surface mount Speaker with 105 ° conical coverage, 200 watts RMS Power, 90 dB SPL sensitivity with the features of the white AcousticDesign Series QSC AD-S8T is a transformer-equipped 8" surface-mount loudspeaker supplied with the award-winning X-Mount system, making it suitable for 70/100V or 8-ohm operation in a variety of foreground and background music applications, whether installed in horizontal, vertical, wall, or ceiling deployments

od124364/2024_2025 : Supply of 2 channel class D professional power amplifier with DSP,continuous power 400 watts/ch at 8D, 600 watts/ch at 4D with features High peak output power with up to 1600 watts from the GXD 4 and a whopping 4500 Watts from the GXD 8, Power levels matched to the most popular loudspeakers and optimized for maximum real-world headroom into 4Ω and 8Ω speaker systems, Class D output stage with a universal power supply for high performance and efficiency, Extensive and powerful loudspeaker processing built in. Includes high and low-pass filters, 4-band parameteric EQ, limiting, and delay, E Series Entertainment System DSP Tunings are now available for GXD processing amplifiers, Large LCD display simplifies amplifier setup and indicates amp status., Inputs: Parallel XLR and 1/4-inch TRS connectors for compatibility with any source while providing convenient loop-thru capability, Precision rotary encoders for gain and DSP parameter control., Outputs: Professional binding post and NL4 connectors (compatible with NL2) provide for mono and bi-amp speaker connections, Digital limiting automatically protects the amplifier from damage due to temperature rise or overdrive, Adjustable speaker protection to match your loudspeaker’s power and impedance, Front panel LEDs indicate signal presence, input overload, and amplifier clipping

od124366/2024_2025 : Supply of 12 channel subwoofer with 2000W Peak power, 2000 watts peak power, Nominal 400 Watts 10Hz - 200Hz Frequency Response, 155 mm Double Heavy magnet for better power handling and punchy sound,Durable rubber surround, Easy connections etc all complete

od124367/2024_2025 : Supply of 16 channel mixing Console, 10 Mic / 16 Line Inputs (8 mono + 4 stereo), 4 GROUP Buses + 1 Stereo Bus, 4 AUX (incl. FX), +48V phantom power with features of 16-Channel Mixing Console, Max. 10 Mic / 16 Line Inputs (8 mono + 4 stereo,4 GROUP Buses + 1 Stereo Bus, 4 AUX (incl. FX), Å“D-PRE mic preamps with an inverted Darlington circuit, 1-Knob compressors, High-grade effects: SPX with 24 programs, PAD switch on mono inputs, +48V phantom power, XLR balanced outputs, Internal universal power, supply for world-wide use, Rack Mount Kit Included, Metal chassis, Dimensions(W”H”D): 444 mm x 130 mm x 500 mm (17.5" x 5.1" x 19.7"), Net Weight: 6.8 kg (15.0 lbs.)

od124368/2024_2025 : Supply of Wired Handheldmicrophonefeatures of with an XLR to 1/4” cable, enabling direct connection to an amplifier, speaker, or karaoke machine featuring a 5m XLR 3-pin to 1/4 inch (6.35mm) mic input jack. The dynamic vocal microphone is shielded by a two-tier PVC, ensuring thickness for excellent, transparent sound transmission without any loss. With its 16.4 ft-long cable, the corded microphone allows unrestricted movement

od124370/2024_2025 : Supply of Wireless Lapel microphone with Wireless microphone set included headset microphone and Clip-on Lavalier Microphone Body pack Transmitter, Receiver with 1/4" Plug, Solid metal collar clip and windscreen reduces plosives, wind, and breath sounds. Female 1/4" to 1/8" TRS adapter converter cord (for camera). 1/4" to 1/8" TRRS adapter cable

od124371/2024_2025 : Supply of 18" Desktop mini-condenser gooseneck microphone with Adjustable Gooseneck Mic: 18-inch bi-fold gooseneck offers more convenience. You can adjust the microphone direction and angle easily and conveniently to cope with desktops of different heights and widths. Multifunctional Mic Base: Base with Anti-slip foot pad, ON/OFF switch for your convenience. Mic Power Source: The Microphone Transmitter can be powered by 2x AA batteries (batteries not included). We recommend using AA alkaline batteries for optimal and long-lasting performance. Fix the XLR cable into the microphone base & Connect the base to the mixer, amplifier, etc

od124372/2024_2025 : Supply of 5200 lumens LCD WUXGA(1920XI200) laser projector with vivid images with the Panasonic PT-VMZ51 5200-Lumen WUXGA Laser 3LCD Projector. Showcase your work on a wall or screen in 1920 x 1200 resolution in fully lit rooms, thanks to the laser light source emitting up to 5200 lumens of brightness. With a short throw of 1.09 to 1.77:1, you can project an image of up to 60" from just 4.6' away. With optical zoom and Digital Zoom Extender, the throw can go up to 2.21:1 for displays as large as 300"

od124373/2024_2025 : Supply of projector Ceiling mount kit, features of Min. 1.5feet & Max. 3ft. Adjustable, Max. load Capacity – 12 kg / 44 lbs / tilt: +/-15, Cable can be put through the pole Very light and capable of supporting wide range of projectors., For Sony / Samsung / Sanyo / Dell / Optoma / Benq / Epson / Acer / 3M / Asus / In Focus / Hitachi / LG / Viewsonic etc

od124374/2024_2025 : Supply of 133 inch motorized projector screen, features of ELCOR liteseries, Motorized projector screen, Actual viewing area 65″Height x 116″width with 133″ Diagonal in 16:09 Aspect format, Imported matte white fabric in 1.1 Gain with Black back backing for excellent Quality., 4-side black masking border for absorb extra light falling

od124375/2024_2025 : Supply of HDMI VGA Transmitter for sending VGA (with audio) and HDMI signals up to 100 m over a single Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable. The VE2812T guarantees reliable transmission of HDMI signals, supporting 3D, Deep Color, and embedded HD lossless audio formats. It also ensures transmission of VGA (with audio) at distance up to 100 m. In addition, it supports Long Reach Mode up to 150 m via a single Cat 5e/6 cable at resolutions up to 1080p

od124376/2024_2025 : Supply of HDMI HDBaseT Receiver features of The VE802R HDMI HDBaseT-Lite Receiver connects with HDBaseT transmitters* to extend signals up to 70m from the source using one Cat 5e/6/6a cable. It supports RS-232 and IR signaling pass-through, allowing you to control the HDMI source device from the remote unit (VE802R) while also granting access to the HDMI display device from the local unit (VE802T). IR signals can also be extended in both directions. The VE802R is HDMI (3D, Deep Color,4k) and HDCP compatible. The VE802R is perfect for a digital entertainment center or any installation that requires superior video quality

od124378/2024_2025 : Supply of 15U Rack with PDU, size of #05587 - 760x600x600 mm, 840x600x600 mm incl. castors, floor-standing with castors, welded body, removable sides , 4mm toughened glass etc complete

od124379/2024_2025 : Supply of 1.8M High Speed Ultra 4K HDMI Cable with Ethernet (Red, 6 Feet/1.8 Meters) Supports 4Kx2K@60HZ, 18 Gbps - 24 AWG - 3D / ARC/CEC/HDCP 2.2 / CL3 - Xbox PS4 PC HDTV

od124380/2024_2025 : Supply of 3 M High Speed Ultra 4K HDMI Cable with Ethernet (Red, 6 Feet/1.8 Meters) Supports 4Kx2K@60HZ, 18 Gbps - 24 AWG - 3D / ARC/CEC/HDCP 2.2 / CL3 - Xbox PS4 PC HDTV

od124381/2024_2025 : Supply of XLR Cable

od124382/2024_2025 : Supply of 1.5 Sq.mm Speaker Cable

od124383/2024_2025 : Laying with the help of clamp/ pipe all type of cables and connection wire including connection with connector etc all complete as per the direction of Engineer in charge

od124384/2024_2025 : Installation, Testing and commissioning of all type AV System including labor, scaffolding, necessary fittings such as srews, bolt etc all complete as per the Direction of Engineer in charge

Fire Protection

od122160/2024_2025 : TERRACE PUMP - 450 LPM, 10 HP LHP SUPPLY INSTALLATION TESTING AND COMMISSIONING OF HORIZONTAL MOUNTED MONO BLOCK THREE PHASE PUMP SET WITH CAST IRON CASING CAST IRON IMPELLER COUPLED TOA SQUIRELL CAGE INDUCTION MOTOR TEFC TYPE WITH SUPPLY CONDITION OF 415 V 3 PH 50 HZ RATED FOR 450 LPM 10 HP AT 2900 RPM

od122161/2024_2025 : MCC PANEL FOR PUMP - AUTOMATIC PANEL SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MOTOR CONTROL PANEL FOR AUTOMATIC OPERATION OF TERRACE PUMP WITH DOL STARTER.THE PANEL SHALL BE PAINTED WITH ANTICORROSIVE LACQUER AND WITH PROTECTIVE LOCKABLE ARRANGEMENT

od122162/2024_2025 : SUPPLY INSTALLATION TESTING AND COMMISSIONING OF WAFER TYPE BUTTERFLY AVLVE, CAST IRON BODY, SS 420 SHAFT, MILD STEEL HANDLE , DISC OF SS 304 PRSSURE RATING OF PN 10 LEVER OPERATED TYPE AS PER IS : 13095 FITTED WITH NECESSARY DIA FLANGES GASKETS NUTS AND BOLTS ETC 100 MM DIA

od122163/2024_2025 : NON RETURN VALVE - SLIM SEAL , CI KARTHAR SUPPLY INSTALLATION TESTING AND COMMISSIONING OF SLIM SEAL TYPE CAST IRON NON RETURN VALVES FITTED WITH NECESSARY DIA FLANGES GASKETS NUTS AND BOLTS ETC

od122164/2024_2025 : PRESSURE SWITCH DANFOSS SUPPLY INSTALLATION TESTING AND COMMISSIONING OF PRESSURE SWITCH FOR AUTOMATIC OPERATION OF PUMPS

od122165/2024_2025 : PRESSURE GAUGE H GURU SUPPLY INSTALLATION TESTING AND COMMISSIONING OF PRESSURE GAUGE OF 0-12 KG RANGE WITH 4" SIZE DIAL

od122166/2024_2025 : MS " B " CLASS PIPE - ABOVE GROUND JINDAL SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MS " B " CLASS PIPES CONFIRMING TO IS : 1239 WITH SPECIALS CONFIRMING TO IS : 1239 PART II SUCH AS ELBOWS REDUCERS FLANGES ETC INCLUDING CUTTING WELDING FIXING ON WALLS OR CEILING BY USING SUITABLE SUPPORTS WITH TWO COATS OF ZINC CHROMITE YELLOW PRIMER AND ENAMEL PAINT RED COLOUR 100 MM DIA

od122167/2024_2025 : MS " B " CLASS PIPE - UNDER GROUND JINDAL SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MS " B " CLASS PIPES CONFIRMING TO IS : 1239 WITH SPECIALS CONFIRMING TO IS : 1239 PART II SUCH AS ELBOWS REDUCERS FLANGES ETC INCLUDING CUTTING WELDING AND LAYING UNDER GROUND WITH COATING OF ANTICORROSSIVE MATERIAL AND WRAPPING TREATMENT OF PIPE 2 MM THICKNESS 100 MM DIA

od122168/2024_2025 : BALL VALVE - 25 MM DIA KARTHAR SUPPLY INSTALLATION TESTING AND COMMISSIONING OF 25 MM DIA BALL VALVE SCREWED END TYPE WITH CAST IRON BODY

od122169/2024_2025 : AIR RELEASE VALVE - 25 MM DIA KARTHAR SUPPLY INSTALLATION TESTING AND COMMISSIONING OF 25 MM DIA AIR RELEASE VALVE SCREWED END TYPE WITH CAST IRON BODY

od122170/2024_2025 : FIRE BRIGADE INLET - 3 WAY KARTHAR SUPPLY INSTALLATION TESTING AND COMMISSIONING OF FIRE BRIGADE INLET CONNECTION WITH 3 NOS OF 63 MM BUILT IN NON RETURN VALVES IN 100 MM PIPE MANIFOLD DIRECTLY CONNECTED TO RISER

od122171/2024_2025 : HYDRANT VALVE KARTAR SUPPLY INSTALLATION TESTING AND COMMISSIONING OF STAINLESS STEEL OBLIQUE TYPE SINGLE HEADED HYDRANT VALVE SS : 304 OF 63 MM DIAFLANGED INLET AS PER PN 16 AND 63 MM DIA FEMALE INSTANTANEOUS OUTLET WITH STAINLESS STEEL INSTANTANEOUS COUPLING ADAPTOR WITH PVC BLACK CAP ETC

od122196/2024_2025 : HOSE REEL DRUM - IMPORTED KARTAR SUPPLY INSTALLATION TESTING AND COMMISSIONING OF HYDRAULIC HOSE REEL DRUM [ WALL MOUNTING TYPE ] HAVING IS: 884 STANDARD WITH SWINGING DRUM POWDER COATED RED FINISHED AT AN OPERATING PRESSURE OF 150 PSI AND FLOW RATE OF 16 GPM AT 100 PSI WITH 19 MM PVC HOSE HAVING LENGTH OF 30 MTR WITH STOP COCK AND PVC NOZZLE AND OTHER FIXING ACCESSORIES

od122172/2024_2025 : FIRE HOSE KARTAR SUPPLY INSTALLATION TESTING AND COMMISSIONING OF FIRE HOSE OF UL LISTED AND IS 636 TYPE A IN 15 MTR LENGTH OF 63 MM DIA WORKING PRESSURE OF 175 PSI TESTED AT BURSTING PRESSURE OF 640 PSI WITH STAINLESS STEEL COUPLING BINDED WITH STAINLESS STEEL WIRE

od122173/2024_2025 : BRANCH PIPE KARTAR SUPPLY INSTALLATION TESTING AND COMMISSIONING OF STAINLESS STEEL BARNCH PIPE WITH 63 MM HEXOGONAL BASE NOZZLE

od122174/2024_2025 : HOSE BOX - SINGLE DOOR FRIENDS SUPPLY INSTALLATION TESTING AND COMMISSIONING OF SINGLE DOOR HOSE CABINET OF INTERNAL TYPE TO PLACE ONE CP HOSE ALONG WITH COUPLINGS AND ONE BRANCH PIPE

od122288/2024_2025 : ABC FIRE EXTINGUISHER - 4 KG LIFEGUARD SUPPLY INSTALLATION TESTING AND COMMISSIONING OF ABC TYPR FIRE EXTINGUSHER OF CAPACITY 4 KG WITH CONTROLLABLE DISCHARGE MECHANISUM

od122175/2024_2025 : FACP - FIRE ALARM CONTROL PANEL AGNI SUPPLY INSTALLATION TESTING AND COMMISSIONING OF 4 ZONE CONVENTIONAL FIRE ALARM PANEL WITH 2 X 16 CHARACTER LCD DISPLAY NO / NC CONTACT FOR FIRE AND FAULT LCD AND LED INDICATION FOR OPEN SHORT CIRCUIT FIRE IN EACH ZONE ETC

od122176/2024_2025 : SMOKE DETECTOR SYSTEM SENSOR SUPPLY INSTALLATION TESTING AND COMMISSIONING OF SMOKE DETECTOR WITH BASE PHOTO ELECTRIC TYPE WITH ALL FIXING ACCESSORIES

od122177/2024_2025 : MCP - MANUAL CALL PONIT [ ABS ] AGNI SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MAUAL CALL POINT OF RED COLOURED TOUGH DURABLE HIGHLY VISIBLE WITH ALARM LED TO INDICATE ALARM CONDITION AVAILABLE FOR FLUSH OR SURFACE MOUNTING

od122178/2024_2025 : SUNDER [ ABS ] AGNI SUPPLY INSTALLATION TESTING AND COMMISSIONING OF ELECTRONIC SOUNDER FOR PROVIDING AN AUDIO WARNING WHICH IS SUITABLE FOR PLACE WHICH NEED AUDIO INDICATION

od122179/2024_2025 : CABLING POLYCAB SUPPLY INSTALLATION TESTING AND COMMISSIONING OF PVC INSULATED 1 SQ MM COPPER CABLE

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

od122181/2024_2025 : SIGNAGES - MCP & FIRE STATION AGNIGOLD SUPPLY INSTALLATION TESTING AND COMMISSIONING OF SIGNAGES FOR MAUAL CALL POINT AND FIRE STATION OF AUTOGLOW TYPE, SIZE 12 " x 6 " AS PER INDIAN STANDARDS

od130232/2024_2025 : SIGNAGES - MCP & FIRE STATION AGNIGOLD SUPPLY INSTALLATION TESTING AND COMMISSIONING OF SIGNAGES FOR MAUAL CALL POINT AND FIRE STATION OF AUTOGLOW TYPE, SIZE 12 " x 6 " AS PER INDIAN STANDARDS

Fire Protection- Approval Fee (821.71 Sqm X Rs. 214.94/sqm)

Liaison charge for Preparation of completion Report, Arranging for Inspection and obtaining approval from Electrical Inspectorate, receiving the safety certificate for energisation, fees, deposit including necessary statutory fees/charges as per actual bill submitted (Deduct 2 times the amount of Item no. 1.58)

EXCLUSIVE OF GST

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of Insurance,Transportation, delivery and installation cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD specification and direction of Engineer at site.

5.CEMENT: Make use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

6.CENTERING & SHUTTERING: (Centering and shuttering for different category of work may be considered separately.)

7.RCC: (Assessment of strength of concrete by Cube testing at Approved Govt labs as per IS) Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

8.STEEL REINFORCEMENT: Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference

9. SOLID BLOCK MASONRY: Min. average compressive strength as per IS shall be 40-50kg/cm2 and has to be assessed by testing at Govt. lab. ( Variation in rate due to change in size of block and level of floor as per DSR/PRICE has to be considered)

10.VETRIFIED FLOOR TILES/ CERAMIC GLAZED WALL TILES: Make: Khajaria, Jhonson, RAK, NITCO, Cera or Eq. in the order of preference and prior sample approval from KEL, Client

11.Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

12. ACRYLIC SMOOTH EXTERIOR PAINT/ SYNTHETIC ENAMEL PAINT/WHITE CEMENT BASED PUTTY/ CEMENT PRIMER: Make: Asian, Berger, Nerolas or eq. in the order of pref.

13.PLUMBING & SANITARY FITTINGS: Note: Make of Water supply and sanitary items: Best branded ISI make Jaquar, Cera, Hindware, Parryware or eq. in the order of pref. Water pipe: Supreme, Finolex or eq. with IS and all fittings with IS.

14.ELECTRICAL: Note: Rate should be inclusive of preparation of schematic diagram and getting approval from KSEB/Electrical Inspectorate. Statutory fees paid to KSEB/EI shall be paid by us separately.

Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

saaj constructions

CUBIX INFRASTRUCTURES