Construction work of Non-Residencial Buildings in Newly Formed Tehsil Kalinagar of District Pilibhit

Amount

Excavation in foundation in ordinary soil (Loam, clay or sand) including lift up to 1.50 M and lead up to 30 M and including filling watering and ramming of excavated earth in to the trenches or in to the space between the building and the side of foundation trenches. [S.N-251,Ch-4]

Construction of subgrade and earthen shoulders with approved material obtained from boeeowpits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300-2. Clause No. 3.18 (305). Carted upto 3 km

Concrete with 4 cm. Guage Brick ballast ,coarse sand and cement in proportion of 8:4:1 in foundation and under floors including supply of all materials, labour and T&P etc. required for proper completion of work. (S.I. No. 275 ch-5)

Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 Kms. From the site of work and including watering, dressing etc. Rate to include cost of all materials labour T&P etc. required for proper completion of work. (S.I. No. 255 ch-4)

Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under the alround the column pots wall trenches basement excavation top surface of plinth filling junction of wall and floor along externel perimeter of building expension joints surrounding of pipes and conduit etc. complete (plinth area of the building at ground floor only shall be measured as per I.S. 6313 (part II 1981) Aldrine emulsificable concrete or any other approved material each as Haptrachlor or chlordance will be used the rate of application of chemical emulsion shall be as follows in six stages. '(4) Treatment junction of wall and the floor 7.5 liters /sqm (5) Treatment of soil along external perimeter of building 7.5 liters/sqm. (6) Treatment of soil under apron along external perimter 5 liters/sqm. (As per manufacturer's standard dilution) (S.I. No. New Item 1 ch-8)

R.C.C. work with cement approved coarse sand and 2 cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in lintels of doors and window excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.l. binding wire and includuing Necessary centering and shuttering etc.and also including supply of all materials, labour and T&P etc. required for proper completion of the work. Binding wire cost being included in the item.(SOR No.283 a CH-5)

R.C.C. work with cement approved coarse sand and 2 cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in Slab .excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.l. binding wire and includuing Necessary centering and shuttering etc.and also including supply of all materials, labour and T&P etc. required for proper completion of the work. Binding wire cost being included in the item.(SOR No.284a, CH-5)

R.C.C. work with cement approved coarse sand and 2 cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in the lighter beams i.e. having spans above 6 m.excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.l. binding wire and includuing Necessary centering and shuttering etc.and also including supply of all materials, labour and T&P etc. required for proper completion of the work. Binding wire cost being included in the item.(SOR No.285 CH-5)

R.C.C. work with cement approved coarse sand and 2 cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in Raft Foundation excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.l. binding wire and includuing Necessary centering and shuttering etc.and also including supply of all materials, labour and T&P etc. required for proper completion of the work. Binding wire cost being included in the item.(SOR No.28---- CH-5)

R.C.C. work with cement approved coarse sand and 2 cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in Column excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.l. binding wire and includuing Necessary centering and shuttering etc.and also including supply of all materials, labour and T&P etc. required for proper completion of the work. Binding wire cost being included in the item.(SOR No.289 CH-5)

25 CM 1" thick damp proof coarse with cement and. approved coarse sand 1:2 and including water proofing materials as ordered by the Engineer-in-Icharge in the proportion as specified by the manufactuers including supply of all materials, labour and T&P etc. required for proper completion of the work and including proper curing and shuttering as necessary. SOR 360 Chp. 7

Painting in D.P.C. with two coats of airblown bitumen 85/50 or 85/25 @ about 1.7 kg./sqm including cost of fuel if any. SOR NEW ITEM 1 Chp. 7

M-150 brick work in one cement & six coarse sand mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of work.(S.N.303 Ch-6)

Class 150 brick work in 1:6 cement and course sand mortar in Super Structure upto two level including necessary cutting and moulding of brick as required with all labour and plinth including supply of all material , labour and T&P etc.(S.I. No. 303+310 ch-6)

First class brick work in 1:4 cement and coarse sand mortar in SuperStructure including supply of all materials, labour and T&P etc. required for proper completion of the work. but for wall of half brick (4½'')thick (S.I. No. 305+310a ch-6)

M.S. (Tor steal or plain) in plain work such as R.C.C. or R.B. work including binding for proper shape and including supply of steal and its wastage bend hooks and authorised over lapping shall be measured. (S.N. 504 ch-10)

12 mm thick plaster with one part cement and 4 part Coare sand over brick work minimum thickness not to be less than 1 cm including supply of all materials labour and T&P etc. required for proper completion of the work. [S.N-584i Ch-13]

15 mm thick Plaster with one part cement and 4 part Coare sand over rough face of one brick walls. including supply of all materials labour and T&P etc. required for proper completion of the work. [S.N-584i +596, Ch-13]

6 mm thick plaster with one part cement and 3 part Coare sand over brick work minimum thickness not to be less than 1 cm including supply of all materials labour and T&P etc. required for proper completion of the work. [S.N-584i+587 Ch-13]

Forming groove of uniform size from 12x12mm and upto 25x15mm in plastered surface as per approved pattern using wooden battens nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specification sna direction of the Engineer-in-charge.(DSR.N. 13.76 Ch-13)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.(Size of Tile 60x60 cm) (DSR N.11.41.1 Ch-14)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.(Size of Tile 60x60 cm) (DSR N.11.41.1 Ch-14) in Skirting and dedo

Laying of 25mm thick KOTA Stone of size 45 x 45cm and above flooring over previously prepared base with 2cm thick 1:3 cement and sand mortar including filling of joints with cement mixed with pigment required for matching the shade of floor as per direction of E/l including cutting polishing with wax polish including supply of all materials T&P etc required for proper completion of the work. (SOR. N. New item 1 Ch-14)

Laying of 25mm thick KOTA Stone of size 45 x 45cm and above flooring over previously prepared base with 2cm thick 1:3 cement and sand mortar including filling of joints with cement mixed with pigment required for matching the shade of floor as per direction of E/l including cutting polishing with wax polish including supply of all materials T&P etc required for proper completion of the work. (SOR. N. New item 2 Ch-14)

Supply and fixing 6 mm thick china glazed tiles of first quality in flooring or in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry jointing and polishing complete including supply of all materials, labour and T&P etc. required for proper completion of the work. [S. N. 628 ch-14]

4.00 cm (1 thick 1:2:4 plain cement concrete floor with cement, approved coarse sand and 2 cm.(3/4")graded approved stone shingle laid in panels finished with 3 mm.(1/8")floating coat of neat cement or cement and marble dust in 5:1 as specified over & including 8cm.(3") 'thick. base concrete consisting of cement ,local sand and brick ballast 4cm.(1½") gauge in the proportion of 1 :4:8 and removing any over lapping mortar at the joints of Panels if any and giving them a uniform finish including supply of all materials, labour' and T&P etc. requierd for proper completion of the the work. without base coat. (S.N.605 Ch-14)

Supply and fixing of 35 mm thick commercial quality ply wood board flush shutters generally confirming to I.S. including fixing of wooden cleats and stops and including fixing and adjustment of hinges, bolts nuts handles spring and other fitting but excluding their supply and including painting with two coats of black japan on all iron fitting if necessary screws to be supplied departmentally. [S.I. No. 470 ii ch-9] Single Leaf

Supply and fixing of 35 mm thick commercial quality ply wood board flush shutters generally confirming to I.S. including fixing of wooden cleats and stops and including fixing and adjustment of hinges, bolts nuts handles spring and other fitting but excluding their supply and including painting with two coats of black japan on all iron fitting if necessary screws to be supplied departmentally. [S.I. No. 470 ii+iv ch-9] DoubleLeaf

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainles steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) as per DSR( 2016)-10.28

M.S. or iron work of small sizes and section such as holding down bolts hold fast tierods grating etc. wrought to required from including supply of steal bolts nuts wastage etc. and their fixing requireded for proper completion of the work. (S.I. No. 502 ch-10)

Same as item No. 31but of fabrication of gril and stair case railing and door and window frame inluding cost of hinges (S.I. No. 502b ,502 c ch-10)

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete.(DSR- 14.34)

Providing & Fixing ISI marked 250X16 mm oxdizied MS sliding door bolts with nuts and screws etc. complete (DSR N. 9.62.2 Ch-9) 250mm x 10mm.

Providing & Fixing ISI marked 300X16 mm oxdizied MS sliding door bolts with nuts and screws etc. complete (DSR N. 9.62.1 Ch-9)

Providing & Fixing ISI marked 250X10mm oxdizied MS tower bolt black finish with necessary screws etc. complete.(DSR N. 9.63.1---- Ch-9) (a) 250 mm x 10mm

Providing & Fixing ISI marked 200X10mm oxdizied MS tower bolt black finish with necessary screws etc. complete.(DSR N. 9.63.2 Ch-9)

Providing & Fixing ISI marked MS handles 125 mm confirming to IS 4992 with necessary screws etc. complete. .(DSR N. 9.66.1 Ch-9)

Painting two coat over priming coat (but including cost of proming coat) on steal and other metal surface with superior senthetic enamel paint of standered make brushing to give an even shade and finished and including cleaning the surface all durt dust and other foreing metter sand preparing and stripping including cost matter and scoured with wire brushes fine steal/wood scrappers sand preparing and knotting including coat of all and supply of all materials, labour and T&P etc. required for proper completion of the work. [S.I. No. New 1+2+4(iii) ch-15]

Painting two coat over priming coat (but including cost of proming coat) on wood work and plaster surface with superior senthetic enamel paint of standered make brushing to give an even shade and finished and including cleaning the surface all durt dust and other foreing metter sand preparing and stripping including cost matter and scoured with wire brushes fine steal/wood scrappers sand preparing and knotting including coat of all and supply of all materials, labour and T&P etc. required for proper completion of the work. [S.I. No. New 1b+2+4(iii) ch-15]

Supply and fixing 4.00 mm thick glass panes of approved quality with brade and putty for window and vantilator mann section or whereever is required on other places including cartage of all item etc. [DSR.N 10.30.1 Ch-10]

Distempring 2 coat with oil bound distemper of approved band and manufacture and required shade on un decorated wall surface to with an even shade over and including a primer coat with cement primer of approved brand and manufacture such as of British, Shalimar asian paint after throughtly brushing the surface free from mortar droppimgs and other froeign matter and also including preparing the surface even and sand prepared smooth including cost of all materials. [S. No. 649+650 Ch-15]

Finishing walls with Acrylic Smooth exterior paint of required shade :-.New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10sqm.). [DSR. No. 13.46.1 ch-15]

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. [DSR. No. 13.80 ch-15]

Providing and laying "Brick Coba" 12mm thick laid with M-150 class brick bat coba 7.50 cm thick with gap of 15 mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finished smooth & top mashed false square 30 cm. x 30 cm. and side wall parapet shall be mono tythic plaster wall upto 30 cm. higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonary Coba with top finished plaster mixed with acetic water proofing compound @ 2% by weight & including S/o all material, labour T & P etc. complete for proper completion of work.(S.N. New Item-1 Ch-11)

Providing & laying of Brick ballast filling under floor of toilets & other sunken roofs.(as per AR)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. b) First layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. DSR 22.5

Providing wood work in frames in frames of doors, windows, clearstory windows and other frames, wrought framed and fixed in position with second class teak wood.( As per D.S.R 9.1.1 Ch-9) Wooden Railing with handrail on top

Polishing on wood work with ready made wax polish of approved brand and manufacture( As per Sor DSR 13.69, Ch-15)

Checkered Terrazo tile 20mm. Avarage thick marble chips of size upto 6mm in floors on 25mm mm thick bed of mortar 1:1:1 (1lime putty :1surkhi :1coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete.[DSR. No. 11.20.3 ch-11] with dark Sade pigment

Supply and fixing of 32 mm thick commercial quality ply wood board flush shutters generally confirming to I.S. including fixing of wooden cleats and stops and including fixing and adjustment of hinges, bolts nuts handles spring and other fitting but excluding their supply and including painting with two coats of black japan on all iron fitting if necessary screws to be supplied departmentally. [S.I. No. 470 i ch-9] Single Leaf

20 mm thick cement plaster in dado or skirting in 1:3 consisting of one part of cement and 3 part approved coarse sand laid in panels finished with 3mm floating coat of neat cement and marble dust in ratio of 5:1 including supply of all materials labour and T&P etc. required for proper completion of the work. [DSR.N-13.9.2 Ch-13]

Providing and fixing 5.5 m thick and 3.50 cm depth glass strips in joints of floors and skirting or dado add the time of laying floors flush with floor level including supply of all materials, labour and T&P etc. required for proper completion of the work. [S.I. No. 631 (b ) ch-14]

Supply and fixing of 32 mm thick commercial quality ply wood board flush shutters generally confirming to I.S. including fixing of wooden cleats and stops and including fixing and adjustment of hinges, bolts nuts handles spring and other fitting but excluding their supply and including painting with two coats of black japan on all iron fitting if necessary screws to be supplied departmentally. [S.I. No. 470 i ch-9] Double Leaf

Providing and fixing cup board shutters with 25mm thick veneered particle board IS : 3097 marked exterior grade (Grade I) of approved make including lind class teak wood lipping of 25mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges complete as per direction of Engineer-in­ Charge.With non decorative veneering on both sides. (As per SOR DSR 9.130.2 Ch-9)

Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanity counters ,window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.Plain white marble/ Udaipur green marble/ Zebra black marble (As per SOR DSR 8.2.1.2)

Supplying and fixing rolling shutters of approved make of 80x125 mm (3 x 3½") gauge cold rolled M.S laths inter locked throughout their entire length and joined together at the end by end locks and mounted on specially designed pipe shaft with brackets side guides and arrangement for inside and outside locking with push and pull operations complete but excluding the cost of top cover and spring.(aS PER SOR 520, CH-10)

Providing & fixing ball bearing for rolling shutters(As per Sor 523, Ch-10)

Providing and fixing 27.5 cm. long wire spring grade no. 2 for rolling shutters.(As per Sor 521)

Providing and fixing top cover for rolling shutters. 18 guage(As per Sor 522,ch-10)

Making Drip Course in sun shade or facia with 1 :3 cement and fine sand mortar as per direction of E/I. including supply of all materials, labour, T & p---etc(As per Sor S.N.600)

2.5 cm (1 thick 1:2:4 plain cement concrete floor with cement, approved coarse sand and 2 cm.(3/4")graded approved stone shingle laid in panels finished with 3 mm.(1/8")floating coat of neat cement or cement and marble dust in 5:1 as specified over & including 8cm.(3") 'thick. base concrete consisting of cement ,local sand and brick ballast 4cm.(1½") gauge in the proportion of 1 :4:8 and removing any over lapping mortar at the joints of Panels if any and giving them a uniform finish including supply of all materials, labour' and T&P etc. requierd for proper completion of the the work. without base coat. (S.N.605 Ch-14)

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. DSR 9.51.2

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) DSR 12.22

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete (20 mm dia) DSR 9.46.2

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets nd shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat DSR 12.47.2

Providing & fixing soil, waste and ventpipes. a) 100mm dia cast iron S & S pipe. DSR 17.35.1.1

Providing & fixing soil, waste and ventpipes. b) 75mm dia sand cast iron S & S pipe. DSR 17.35.1.2

Providing lead caulked joints to sand castiron/ centrifugally cast (spun) iron pipes& fitting of diameters. a) 100mm DSR 17.58.1

Providing lead caulked joints to sand castiron/ centrifugally cast (spun) iron pipes& fitting of diameters. a) 75mm DSR 17.58.2

Providing & fixing M.S. holder bat clampsof approved design to sand castiron/centrifugally cast (Spun) iron S & Spipe embeded in & including cementconcrete blocks 10x10x10cm. of 1:2:4 mix(1 cement : 2 coarse : 4 graded stoneaggregate 20mm nominal size). Including cost of cutting holes & makinggood the walls etc. a) for 100mm dia pipe. DSR 17.59.1

Providing & fixing M.S. holder bat clampsof approved design to sand castiron/centrifugally cast (Spun) iron S & Spipe embeded in & including cementconcrete blocks 10x10x10cm. of 1:2:4 mix(1 cement : 2 coarse : 4 graded stoneaggregate 20mm nominal size). Including cost of cutting holes & makinggood the walls etc. a) for b) for 75mm dia pipe. DSR 17.59.2

Providing & fixing cast iron trap of self cleansing design with or without ventarm complete, including cost of cutting & making good the walls & floors. a) 100mm inlet & 75mm outlet. DSR 17.60.1.2

Providing & fixing cast iron trap of self cleansing design with or without ventarm complete, including cost of cutting & making good the walls & floors. a) 100mm inlet & 100mm outlet. DSR 17.60.2.1

Providing & fixing sand cast iron coller. a) 100mm dia. DSR 17.57.1.2

Providing & fixing sand cast iron coller. b) 75mm dia. DSR 17.57.2.1

Providing and fixing single equal plainjunction of required degree.(Plane 'Tee' ) a) 100x100x100mm DSR 17.50.1.2

Providing and fixing single equal plainjunction of required degree.(Plane 'Tee' ) b) 75x75x75mm DSR 17.50.2.1

Providing and fixing terminal guard. a) 100mm DSR 17.56.1.2

Providing and fixing terminal guard. b) 75mm DSR 17.56.2.1

Providing and fixing plain sand cast iron'S' or 'P' sanitary bend. a) 100mm DSR 17.39.1.2

Providing and fixing plain sand cast iron'S' or 'P' sanitary bend. b) 75mm DSR 17.39.2.1

Providing, fixing G. I. pipes complete with G. I. fittings and clamps including cutting and making good the walls etc. (internal work) - (Exposed on wall) a) 15mm dia nominal bore. DSR 18.10.1

Providing, fixing G. I. pipes complete with G. I. fittings and clamps including cutting and making good the walls etc. (internal work) - (Exposed on wall) a) 20mm dia nominal bore. DSR 18.10.2

Providing, fixing G. I. pipes complete with G. I. fittings and clamps including cutting and making good the walls etc. (internal work) - (Exposed on wall) a) 25mm dia nominal bore. DSR 18.10.3

Painting G. I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work. a) 15mm dia nominal bore. DSR 18.38.1

Painting G. I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work. a) 20mm dia nominal bore. DSR 18.38.2

Painting G. I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work. a) 25mm dia nominal bore. DSR 18.38.3

Providing & fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS : 8931. a) 15mm nominal bore DSR 18.52.1

Providing & fixing white vitreous china water closet squatting pan ISI marked (Indian type W.C. pan) with 100mm sand cast iron P or S trap, 10/12.5 litrs PVC low level flushing cistern with fittings & brackets 40mm dia C.P. flush pipe with fitting & clamps, 20mm over flow pipe with specials and mosquito proof coupling of approved municipal design, painting wherever required including cutting & making good the walls & floors where required. Orissa Pattern W.C. pan of size 580x 440m with integral type foot rests flush pipe and over flow arrangement. DSR 17.1.1

Providing & fixing white vitereous china pedestal type water closet ( European type ) with seat and lid . 10 liter low level flushing cistern with fitting & C.I. / M.Sbrackets . 40mm flush bend. Over flow arrangement mosquito proofwith specials of standard mark andcoupling of approved of fitting and brackets.Cutting and including painting of fitting and brackets.Cutting andmaking good the walls and floors wherever required. W.C. pan with ISI marked white solid plastic seat and lid with white vitreous china flushing cistern &C.P flush bend. DSR 17.3.1

Providing & fixing white vitreous china wash basin with C.I. brackets painted white, 15mm C.P. brass pillar taps, C.P. brass chain with rubber plug, 32mm C.P. brass waste of standard pattern including cutting & making good the walls wherever required. a) Flat back wash Basin size 550x400 mm with single 15mm C.P. brass pillar tap. DSR 17.7.4

Providing and fixing flexible P.V.C. wastepipe for sink or wash basin including PVC .waste fittings completea) 32mm dia mm dia DSR 17.28.1.1

Providing & fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick asbestos cement sheet ground fixed to wooden cleats with C.P. brass screws and washers. DSR 17.31

Providing & fixing 60x2cm. C.P. brasstowelrail complete with C.P. brassbrackets fixed to wooden cleats with C.P.brass screw. DSR 17.33

Providing and fixing white vitreous chinatoilet paper holder DSR 17.34.2

Providing and fixing white vitreous chinaflat back or wall corner type lipped fronturinal basin of 430x260x350mm and340x410x265mm sizes respectivelywith automatic flushing cistern withstandard flush pipe and C.P. brassspreaders with brass unions andsingle half stall urinal basins with 5 litre. Single half stall urinal basins with 5 litre P.V.Cautomatic flushing cistern DSR 17.5.1

Providing & fixing brass gate valve withC. I wheel of approved quality (screwedend) c) 25mm dia nominal bore. DSR 18.17.1

Providing and fixing 45 cm longunplasticised PVC connection pipe withbrass unions. a) 15mm nominal bore DSR 18.21.2.1

Providing & fixing 15 mm nominal bore CP brass bib cock of approved quality conforming to IS 8931. a) 15mm nominal bore DSR 18.49.1

Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. a) 15mm nominal bore DSR 18.51.1

Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931. a) 15mm nominal bore DSR 18.53.1

Providing and fixing sand cast iron jali(grating) for floor/nahani trap. a) 100mm dia DSR 17.29

Providing and fixing ball Floating valve(brass) of approved quality complete. (High or low pressure with plastic floats). a) 25mm. Nominal bore DSR 18.18.3

Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Capacity 2000 litre(2Nos) DSR 18.48

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes. a) 110mm diameter DSR 12.41.2

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming toIS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansi. Coupler 110 mm DSR 12.42.1.2

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming toIS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansi. Single tee without door110x110x110 mm DSR 12.42.4.2

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming toIS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansi. Shoe (Plain)110 mm DSR 12.42.6.2

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 a) 110mm DSR 12.43.2

Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required,in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m.a) Pipes 80mm to 300mm diameter. DSR 2.10.1.2

Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. a) 100mm diameter DSR 19.1.1

Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. a) 150mm diameter DSR 19.1.2

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design. a) 100mm diameter S.W. Pipe DSR 19.2.1

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design. b) 150mm diameter S.W. Pipe DSR 19.2.2

Providing and fixing square mouth S.W. Gully trap grade 'A' complete with C.I. grating brick masonry chamber with F.P.S. bricks of class designation 75 and water tight C.I. cover with frame of 300 x 300mm. size (inside) the weight of cover to be not less than 4.50 Kg and frame to be not lessthan 2.70 Kg as per standard design. a) 150 x 100 mm. size P type DSR 19.4.2.1

Constructing brick masonry manhole with 75 class designation F.P.S. bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand: 4graded stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix. (1 cement :4 coarse sand: 8 graded stone aggregate 40mm nominal size) inside plasstering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4. (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design. a) Inside size 90x80 cm & 45 cm deep including C.I. cover with frame (light duty) total wt. of cover & frame to be not less than 38 Kg (wt. of cover 23 Kg & wt. of frame 15 Kg. DSR 19.7.1.1

First class brick work in 1:4 cement and coarse sand mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work. SOR 305

Providing and fixing stainless steelkitchen sink as per IS 13983 with CIbrakets and stainless steel plug 40mmincluding painting of fittings and brakets,cutting & making good the wallswherever required. With out drain board Size 470x420mm bowl depth 178mm DSR 17.10.2.3

Mild steel or iron work in heavy sizes such as trusses; builts up gates, door, frames, record racks roof work, gates etc. wrought to required form including drilling holes, rivetting or welding where necessary, and also including supply of steel, bolts, nuts etc. & their fixing required for proper completion of the work. SOR 503

Providing & Laying 80mm dia. G.I pipe DSR 1552

2.5 cm (1.0") thick 1:1.5:3plain cement concrete floor with cement, approved coarse sand and 2 cm (3/4") graded approved stone shingle laid in panels finised with 3mm (1/8") floating coat of neat cement or cement and marble dust in 5:1 as specified without base concrete

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density complete work.

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) DSR 5.11.1

Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : 100 mm dia pipe. DSR 18.27.1

Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : 125 mm dia pipe. DSR 18.27.2

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 100 mm diameter Class I DSR 18.31.1.1

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 125 mm diameter Class I DSR 18.31.2.1

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. 300 mm dia DSR-23.2.1.1

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia having minimum wall thickness 5.00 mm DSR-23.10.1

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia having minimum wall thickness 5.40 mm DSR-23.10.3

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia metre DSR-23.11.3

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.DSR-23.7

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. DSR-23.12

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia DSR-23.13.3

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp DSR-23.14.3

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia DSR-23.15.3

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 100 mm diameter DSR-18.31.1.1

Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-incharge (payment for providing grooves shall be made separately). DSR 13.72

Providing and laying of cement concrete in base excluding the cost of centring and shuttering by 1:2:4 (1 cement : 2 coarse sand : 4 gradded stone aggregae 40mm nominal size) SOR 279

Supplying and stacking at site. 90 mm to 45 mm size stone aggregate RMR

Supply and stacking of stone chippings of 11.20mm size RMR

Supply and stacking of moorum at site. RMR

Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars. DSR 19.15.1

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 500mm internal diameter DSR 19.19.2.2

100 MM. S.C.I. trap with 100 mm inlet and 100 mm Outlet. DSR 17.60.1.1

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) upto haunches of S.W. Pipes including bed concrete as per standard design. a) 150mm diameter S.W. Pipe DSR 19.3.2

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) upto haunches of S.W. Pipes including bed concrete as per standard design. b) 200mm diameter DSR 19.3.3

Drilling of 300mm dia bore hole manually. DSR 23.2.1.1

Supply of 150mm dia slotted rigid PVC pipe (4 Kg./sqcm pressure rating) and accessories. DSR 23.4.2

Providing and packing of coarse sand around the pipe. DSR 23.7

Providing and laying of 80 mm thick Interlocking cement concrete tiles (300mpa) including laveling and dressing of surface to required level and slope, filling joints with local sand including the cost of material,labour T&P etc.required for proper completion of work as directed by Engineer-in-Charge. ch. 20 N.I. 1

Wiring point for light with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit partly laid in slab and partly concealed in wall with modular switches.complete in all respect. 138C+187A

Wiring point for two way light with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit partly laid in slab and partly concealed in wall with two way modular switches.complete in all respect. 139C+187B

Wiring point for Fan/Fresh air fan with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit concealed in wall with modular switches.complete in all respect. 140C+187A

Wiring point for Plug /computer/TV/Aquaguard with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduitpartly laid in slab and partly concealed in wall with modular switches.complete in all respect. 141C+187C

Wiring point for call bell with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit partly laid in slab and partly concealed in wall with modular switches.complete in all respect. 142C+187E

Wiring point for Street Light with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit partly laid in slab and partly concealed in wall with modular switches.complete in all respect. 143C+187D

Wiring point for Exhaust fan with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit partly laid in slab and partly concealed in wall with modular switches.complete in all respect. 144C+187D

Add for Inverter wiringin wiring point for light/fan/plug with 1.5 sqmm Cu wire. 189A

Submain(FRLSH multistrand copper conductor cable) in PVC conduit partly laid in slab and partly concealed in wall 2 no.2.5 sqmm & 1 no.1.5 sqmm earth wire for power plug 1307C

Same As Above but 2 no.4 sqmm & 1 no.2.5 sqmm earth wire for power plug 221 C

Same As Above but 2 no.6sqmm & 1 no.4 sqmm earth wire for AC .222C

Same As Above but 2 no.10 sqmm & 1 no.6 sqmm earth wire for TPNDB to SPNDB. 223C

Same As Above but 2 no.25 sqmm & 1 no.16 sqmm earth wire for TPNDB to SPNDB. 225C

Same As Above but 4no.10 sqmm & 2 no.10 sqmm earth wire for TPNDB to Main Panel 274C

Same As Above but 4no.25 sqmm & 2no.16 sqmm earth wire for TPNDB to main Panel 276 C

S/F of 63 A 415 V metal clad TPN HRC type switch fuse unit on angle iron bracket. Complete in all respect. 327 Cat B

S/F of 32 A double pole metal clad rewireable type switch fuse unit. Complete in all respect. 305

S/F of 100 A 415 V 4 pole moulded case type on load change over with enclosure. Complete in all respect. 378A

S/F of 63 A 415 V 4 pole change over switch on 40mmx40mmx6mm on angle iron frame. Complete in all respect. 377

S/F of call bell approve make 1101

S/F of 3w to 6w LED Decorative Mirror Light (Spot Light) fitting confirming to IP 65 and above protection,complete in all respect.330-660 system lumens, 110lm/W. PF>0.95, THD<20% at full load with 5 year warranty. 1441 A Cat AA

S/F of recess/surface mounting round 10 to 15 W LED Down light.complete in all respect. 1402 Cat AA

S/F of indoor recess mounting LED square fitting 36 to 46 W LED Down light.complete in all respect. 1406 Cat AA

S/F of LED tube light batten fitting suitable for upto 1X22watt LED tube light on surface.complete in all respect. 1413A Cat AA

S/F of 90W LED Street Light Fitting having die cast Al body and diffuser, driver set. Complete in all respectS 1423 Cat AA

S/F of Ceiling Fan 1200 mm sweep complete.without GST. 1501 (ii)

S/F of LED Bulb 15 watt AR

S/F of Exhaust Fan(Light duty) AC 230mm Sweep 230/250V 50 Hz. Complete in all respect. AR-5

S/F of Exhaust Fan(Heavy duty) AC 300 mm Sweep 230/250V 50 Hz. Complete in all respect. AR-6

S/L of 400 sqmm 3.5 core Al conductor pvc insulated armoured served sheathed cable 1100 V grade. Complete in all respect. 501t

S/L of 6 sqmm 3 core Al conductor pvc insulated armoured served sheathed cable 1100 V grade. Complete in all respect. 501e

S/L of 10 sqmm 2 core Al conductor pvc insulated armoured served sheathed cable 1100 V grade. Complete in all respect. 501b

S/F of Brass Nickle plated compression gland for 400 sqmm 4 core 503t

S/F of Brass Nickle plated compression gland for 10 sqmm 2 core 503b

S/F of Brass Nickle plated compression gland for 6 sqmm 3 core 503e

S/F of copper Tin plated lug 6 sqmm 504 b

S/F of copper Tin plated lug 10 sqmm 504 c

S/F of copper Tin plated lug 25 sqmm 504 e

S/F of copper Tin plated lug 400 sqmm 504 o

Supply and burying of safe earthing electrode T-19 Zn-Zinc coated ,Length 3000 mm,outer pipe 48.4 mm X 3.2 mm,inner pipe 26.9 mmX 2.6 mm. Terminal Dia 12 mm,coating 80-100 micron filled with crystalline conductive mixture(CCM) having anti corrosive & conductive property with 50 kgs activated soil(BFC) capable of reducing the soil resistivity with good mixture of retaining capacity etc. complete in all respect. 726B

S/L of 25 mm X 3 mm GI strip from earth electrode .complete in all respect. 716

Supply & Erraction of factory fabricated & wired metal clad dust and vermin proof floor mounting panel.complete in all respect.Incoming-400A/415V MCCB-1 no Outgoing 100 A MCCB-3 no, 63 A MCCB-2no 813 e Cat B

S/F of 6 A to 32 A SPMCB(10KA) C curve. 1002 Cat A

S/F of 63 A SPMCB(10KA) C curve. 1003 Cat B

S/F of 6A to 32A DPMCB(10KA) C curve. 1009 Cat A

S/F of 63 DPMCB(10KA) C curve. 1011 Cat A

S/F of 40 A 4 pole MCCB(10KA) 1020 C atA

S/F of 63 A 4 pole MCCB(10KA) 1020 A CatA

S/F of surface/flush mounting 4 way SPNDB with additional metal door without MCB complete in all respect. As directed at site by engineer in-charge. 1022A catA

S/F of surface/flush mounting 8 way SPNDB with additional metal door without MCB complete in all respect. As directed at site by engineer in-charge. 1024A catA

S/F of surface/flush mounting 12 way SPNDB with additional metal door without MCB complete in all respect. As directed at site by engineer in-charge. 1025A catA

S/F of surface/flush mounting 4way TPNDB (Legrand Lexic) with additional metal door without MCB complete in all respect. As directed at site by engineer in-charge. 1026A catA

S/F of MCB blanking Plate for DB 1034 B

S/F of Danger Board fabricated from 10 gauge M.S. Sheet as per I.E. Rules. 1109

E & T of ceiling fan and regulator 1115

E & T of exhaust fan.complete in all respect 1120

S/F of 16 swg M.S.Drum with luvers duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect 1122A

S/F of shock Treatmemt Chart (prescribed under IE rules) 1134

S/F of Rubber matting1800x900x12 mm tested and chequred 1136

S/F of power plug with 20 Amp/250 V flush type modular switch and 5 pin 20Amp/250V socket on concealed M.S. Box.complete in all respect. 1139A

S/f of sheet steel enclousure fitted with 20 A 2 pin and earth metal clad earth plug and socket complete. 1031 CatA

S/F of Hexagonal Fan Box with hexagonal side of approx 80 mm in length fabricated from 16 SWG MS sheet in corporating 10 mm dia MS round bar duly bend for supporting fan hanger duly painted etc. Complete in all respect. 1149

S/F of electronic fan regulator(Modular)120-280 V ISI marked 1203C

S/F of Modular switch blanking plate for modular switch board. 1.26 DSR

SITC of M.S Black Pipe "C" Class (IS:1239/3589 Including Cutting, welding etc. & providing suitable flanges alongwith necessary fittings viz. bends, tees, reducers etc. & anti-corrosive treatment. Approved by UPPWD 3238 E/M Fire 2014-15 Dt.18.11.14 SL No.1. 100 mm dia.

As Above Item 80 mm dia.

As Above Item 40 mm dia.

SITC of Single headed Hydrant comprising of 80 mm dia. Flanged bend 63 mm dia. SS oblique pattern landing valve complete with blank and Cap . SL No.3

SITC of First aid Hose reel drum with 20 mm dia, 30 m long rubber pipe shut off nozzle, 25 mm dia., gate valve complete conforming to IS: 884/444. SL No.2

SITC of GM Fire brigade 4 way Inlet connection. SL No.15

SITC of Terrace Pump 450 LPM 7.5 HP. Complete in all respect. SL No.12

SITC of C.I double flanged Butterfly Valve complete with nuts, bolts & washers etc. conforming IS 780 SL No.17. 100 mm dia.

80 mm dia.

SITC of cast iron double flanged Non Return Valve complete with nuts, bolts and washers conforming to IS 5312. SL No.16 100 mm dia.

SITC of Hose Box of 18 SWG M.S Sheet with glass Fronted door to accommodate 2 nos. RRL Hose & 1 nos. SS Branch Pipe with nozzel. SL No.7

SITC of RRL Hose 63 mm dia x 15 m long complete with SS coupling conforming to IS: 636. SL No.4

SITC of SS Branch Pipe & Nozzle IS: 903. SL No.5

SITC of Automatic Starter Panel for Terrace Pump suitable 7.5 HP. Complete in all respects. SL No.14

SITC of Pressure Switch. Complete in all respect. SL No.20

SITC of Pressure Gauge. Complete in all respect. SL No.21

Terrace PVC Tank having Capacity of 5000 Liter (Rs. 10/Ltr.) Approved by UPPWD/2014

S/F of 100 Amp. 415 Volt Heavy duty double break HRC Fuse Type metal clad TPN with HRC Fuse Complete. 346

S/Laying of Al. Conductor PVC Insulated armoured served sheated cable 1100 Volt Grade complete. 16 Sqmm. 4 Core 501(i)

S/F Brass Nikle plated compression glad PVC insulated armoured served complete. 16 Sqmm. 4 Core 503(i)

S/F of plain or Pin Type Copper plated cable socket (LUG) complete. 16 Sqmm. 4 Core 504(i)

S/Buring of 600mm X 600mm X 6mm G.I. Plate Vertically for earthing complete. 703

S/F of Vertically down conductor of 32 mm X 6 mm G.I. Pipe stripe etc. Complete. 717

S/F of Danger Board fabricated from 10 Gauge M.S. Sheet Complete. 1109

S/Laying 1800mm X 900mm X 12 thick chequered moting of tested Quality. 1136

Supply & fixing of ABC type Fire Extinguisher 4 kg Capacity. Complete in all respect. 1131

Supply & fixing of Co2 type Fire Extinguisher 4.5 kg Capacity. Complete in all respect. 1132

S/F of 100 Amp. Four pole change over switch with angle iron frame complete. 378(A)

SITC of 6 Zone Fire Alarm Local control Panel for above, complete in all respect with Auto Display. SL No.5

SITC of lonization Smoke Detector as per specifaction including making connections with wire. SL No.7

SITC of Heat Detector ROR Type as per specification including making connection with wire. SL No.8

SITC of Responsce indicator pul stanting type suitebul for including connection. SL No.6

SITC of Electronic LMT Hooter, housed in MS housing suitable for wall mounting/ceiling, including making connection. SL No.2

SITC of Manual Call point Break Glass type housed in MS sheet, including connection. SL No.1

Supply and wiring of submain with 3 no.1.5sq mm pvc insulated 1100 volt grade single core copper conductor cable in 20 mm dia heavy gauge rigid steel conduit on surface complete in all respect. SL No.10

S/L of 4 core copper cable for connect LCP to main panel with PA system SL No.13

S/L of Armoured cable size 1.5 sqmm 3 core complete in all respect. SL No.14

Supply & Fixing of Fire Bucket 4+ Stand. T.S

Suppy & fixing of 6 Mtr. G.I. Octagonal Pole of approved make (top dia 70 mm, Bottom dia 130mm and base plate 12mm thick) having 3mm thickness with Single arm bracket 1 mtr length in 1:2:3 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P Complete in all respect. 647

Supply and Fixing of LED Street light Fitting with mandantory driver set having die cast aluminium body and lessness suitable for 160 watt to 175 Watt and Confirming to IP66 protection having Complany LOGO Engraved complete in all respect Including Labour 1425(A)

Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanised), Length up to 300mm, outer Dia 50 mm inner Dia 25mm, Terminal Dia 12 mm Outer GI Pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti Corresive & conductive property ith 50 kgs activated soil (BFC) capable of retaining capacity and one earthing lead of 25 mm X 3 mm G.I. Stirp, upto switch board (from apron to switch board, the cos to G.I. Strip will be extra) along with 30 cm square C.I. frame with hinged cover & mansonary housing. Make:- As approved in UP. PWD, & CPRI Certified. 725 (A)

Supply and laying of aluminium Condtuctor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc of suitable size or as directed by the Engineer-incharge, complete in all respect. The Armouring of the cable shall be properly connected with the earth condutor by clamps etc. 501(i)

Supply and wiring of submains with 2 Nos 2.5 sqmm & with 1 No earth wire of 1.5 sq mm FRLSH PVC insulated 1100 V grade single core multistand copper conductor cable in existing PVC conduit complete, including supply of all material, labour and T & P etc. required for proper completion of the work as directed by Engineer in charge. 291

Supply and laying of 25mm X 3mmm G.I. Strip from earth electrode directly in the ground as required complete in all respect. 716

S & F surface/flush mounting 4 ways SPN distribution board without MCB complete in all respect, as directed at site by Engineer in Charge. 1022 Cat B

S & F of 63 Amp. D.P. Isolator 1005 (A) Cat B

S & F of 6 Amp. To 32 Amp. SPM (10KA) C Curve 1002 Cat (B)

S /F of PVC corrugated conduits of 32 mm dia meter on surface as sleeving including all labour, T & P etc. Required for proper completion of work as per direction and satisfaction of Engineer in charge. 185 (iv)

S & F of 32 Amp. Four pole change over switch on 25 mm X 25 mm X 3 mm angle iron frame, including the cost of labour T&P painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in Charge. 377 Cat B

S & F of 63 Amp. 415 V metal clad TPN HRC Type switch fuse unit complete with HRC fuse on angle iron bracket complete in all respect. 327 Cat (B)

Wiring point for light with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit concealed in wall with modular switches.complete in all respect.136 C+ 187 D

S/F of LED Street light Fitting with mandantory driver set having die cast aluminium body and lonses suitable for 75 watt to 90 watt and Conforming to IP66 protection having Company LOGO Engraved complete in all respect including Labour. 1423 Cat AAA