Construction of Rajiv Gandhi Govt. Model Day Boarding school at Govt. Sr.Sec.School Rait, District Kangra (HP) (SH Building Portion including Water Supply and Sanitary Installation and Rain water Harvesting System)

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including de-watering removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation as direction of Engineer-in-Charge and returning the stacked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Excavating trenches of required width for pipes, cables, etcetra including excavation for sockets, and dressing of sides, ramming of bottoms, upto any depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm (Twenty centimetree) in depth, including consolidating each deposited layer by ramming, watering, etcetera and disposing of surplus excavated soil as directed including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. .

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings including curved surfaces where ever required as per Architectural drawing, design and specifications and the like floor etcetera including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders lintels window sills, cornices, arches corbelling including curved surfaces where ever required sides and soffits of beams haunchings cantilevers bressumers and lintels upto all depths including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular polygonal in plan including mouldings, cornices etcetera complete as per Architectural drawing, design and specifications including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Stair cases (except spiral stair cases) with slopping or stepped soffits excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor levels as per specifications, approved drawing, design including carriage of material within all heights leads, lifts and other incidentals and as directed by the Engineer-in-charge including incidents. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Edges of slab and breaks in floors and walls under any thickness including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies for all height of and removal of the same for insitu-reinforced concrete & plain concrete work in window sills, cornice and moulding and the like including carriae of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies for all height of and removal of the same for insitu-reinforced concrete & plain concrete work in weather shades, Chhajjas, corbels etcetera including edges including carriae of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surface such as walls (any thickness) partitions and the like including attached, pilasters, buttresses, plinth and string courses and the like including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement isto four sand isto eight graded broken/crushed stone aggregate 40mm (Forty millimetres) nominal size mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Stone filling with hard stone of approved quality under floor including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 (M-Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty niewton per square millimetre) with cement contents not not less than @ 330 kg/cum (at the rate Thre hundred thirty kilogram per cubic metre) or as per approved design mix. All works upto plinth level to give a smooth machanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 (M-Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty niewton per square millimetre) for reinforced cement concrete work @320 kg/cum (at the rate Thre hundred twenty kilogram per cubic metre) or as per approved design mix All works above plinth level upto floor V level to give a smooth mechanically mixed and vibrated inclusing curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with in Cement mortar 1:6 (One cement isto Six coarse sand) etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing tor steel reinforcement for Reinforced Cement Concrete work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying Damp Proof Course 100mm (One Hundred millimetres) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate) 12.5mm (Twelve decimal five millimetres nominal size) and curing complete, as required at site including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 (Viscosity grade-Ten) of approved quality using 1.7 kg/Sqm (One point seven kilogram) per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil etcetera complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Half brick masonry work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point Five) in super structure in Cement mortar 1:4 (One cement isto Four coarse sand) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government.

Second class brick masonry work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point Five) in super structure in Cement mortar 1:6 (One cement isto Six coarse sand) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government.

Second class brick masonry work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point Five) in foundation and plinth in Cement mortar 1:4 (One cement isto four coarse sand) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government.

40 Cm (forty centmetre) thick Cavity wall with second class common burnt clay building bricks with 17cm (seventeen centimetre) wide cavity and consisting 11.5 cm ( Eleven decimal five centimetre) thick inner and outer walls laid in cemnet mortar 1:4 ( one sand isto four sand) and strength with hoop iron and bituminious coated cross ties including making weep hole and vent pipe complete 2 Nos. (two numbers ) 6/8 ( six / eight )width brass in Z- shape crossing each other shall be provided at the interval 90-100 cm ( ninety - hundred centimetre) length horizontal and vertical in cavity wall and curing complete (The mesurement of wall faces only one side will be considered for payment), as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government.

Half brick masonry with Machine made exposed bricks in superstructure above plinth level up to floor V level with Cement mortar 1:4 (One cement isto Four coarse sand) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government

Providing and fixing factory made uPVC white colour casement/ casement fixed glazed windows area above 0.75 sqm (zero point seven five square metre) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm (one point sixty plus minus zero point two millimetre) thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm (one hundred into eight millimetre) size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etcetra Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Casement window single panel with S.S. friction hinges 400 x 19 x 1.9 mm (four hundred into nineteen into one point nine millimetre) made of (big series) frame 67 x 60 mm (sixty seven into sixty millimetre) & sash 67 x 80 mm (sixty seven into eighty millimetre) both having wall thickness of 2.3 ± 0.2 mm (two point three plus minus zero point two millimetre) and single glazing bead / double glazing bead of appropriate dimension complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government

Providing and fixing factory made uPVC white colour casement/ casement fixed glazed windows area above 1.50 sqm (one point five zero square metre) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm (one point sixty plus minus zero point two millimetre) thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm (one hunddred into eight millimetre) size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etcetra Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Casement window double panels with S.S. friction hinges 350 x 19 x 1.9mm (three hundred fifty into nineteen into one point nine millimetre) made of (big series) frame 67 x 60 mm (sixty seven into sixty millimetre) & sash / mullion 67 x 80 mm (sixty seven into eighty millimetre) both having wall thickness of 2.3 ± 0.2 mm (two point three plus minus zero point two millimetre) and single glazing bead/ double glazing bead of appropriate dimension complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government

Providing and fixing factory made uPVC white colour casement/ casement fixed glazed windows of area above 3.00 sqm (three square metre) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm (one point sixty plus minus zero point two millimetre) thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm (one hundred into eight millimetre) size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges 350 x 19 x 1.9 (three hundred fifty into nineteen into one point nine millimetre) made of (big series) frame 67 x 60 mm (sixty seven into sixty millimetre), sash 67 x 80 mm (sixty seven into eighty millimetre), & mullion 67 x 80 mm (sixty seven into eighty millimetre) all having wall thickness of 2.3 ± 0.2 mm (two point three plus minus zero point two millimetre) and single glazing bead/double glazing bead of appropriate dimension complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door area upto 2.00 sqm (two point zero square metre) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm (one point sixty plus minus zero point two millimetre) thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm (one hundred into eight millimetre) size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Casement door with 3D hinges made of (big series) frame 67 x 64 mm (sixty seven into sixty four millimetre) & sash 67 x 110 mm (sixty seven into one hundred ten millimetre) both having wall thickness of 2.3 ± 0.2 mm (two point three plus minus zero point two millimetre) and single glazing bead / double glazing bead of appropriate dimension. complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door of area upto 2.50 sqm (two point five zero square metre) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm (one point sixty plus minus zero point two millimetre) thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Casement door with top hung ventilator with 3D and S.S. friction hinges 400 x 19 x 1.9 mm (four hundred into nineteen into one point nine millimetre) made of (big series) frame 67 x 64 mm (sixty seven into sixty four millimetre), sash 67 x 110 mm (sixty seven into one hundred ten millimetre) & mullion 67 x 80 mm (sixty seven into eighty millimetre) all having wall thickness of 2.3 ±. 0.2 mm (two point three plus minus zero point two millimetre) and single glazing bead / double glazing bead of appropriate dimension complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government

Providing and fixing Fly proof stainless steel wire gauge to doors, windows and clerestory windows with M.S. flat 15x3mm (Fifteen into three millimetre) and nut and bolts complete stainless steel (Grade-304) wire gauge of 0.5mm (Zero point five millimetre) dia wire and 1.4mm (One point four millimetre) wide aperture with matching wood beading on both side complete including entire carriage of material within all leads, lifts and other incidentals,as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 8mm (Eight milimetres) thick anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm (Two hundred millimetre) centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete including entire carriage of materials within all leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 12mm (Twelve milimetres) thick (both Side) Pre-laminated MDF board both side / phenol bonded particle board exterior grade (Grade-I) IS:14587:1998 marked, Frames, backing or studding in uPVC style of encraft or its equivalent etcetera complete as per architectural drawings and directions of Engineer-in-Charge including entire carriage of materials within all leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 35 mm (thirty five millimetre) thick ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st (first) class hard wood and well matched teak 3 (three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked Stainless Steel butt hinges with necessary screws and PGI sheet lining inside of the shutters complete as per architectural drawings and directions of Engineer-in-Charge including entire carriage of materials within all leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 5mm (Five millimetre) thickness (weight not less than 12.50 kg/ sqm) (Twelve point five zero kilogram per sqaure metre) Glass panes of Modi Guard / Saint Gobain / AIS / Atul / Gold Plus in door, window, ventilator shutters and partitions etcetera with EPDM rubber / neoprene gasket etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government.

Providing and fixing 4mm (Four millimetre) thickness (weight not less than 10.00 kg/ sqm) (Ten point zero zero kilogram per sqaure metre) Glass panes of Modi Guard / Saint Gobain / AIS / Atul / Gold Plus in door, window, ventilator shutters and partitions etcetera with EPDM rubber / neoprene gasket etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government.

Providing and fixing 19mm (Nineteen millimetres) thick water proof Termite resistant commercial board of Uniply/ Green ply/Century ply/Kit ply /Duro ply / Marino (ISI Marked ) for cup board shutters including 19 mm (Nineteen millimetre) thick shelves and back side of the cub board shall be of 8 mm (Eight millimetre) thick ply and all cut portions of shutter shall have 6mm /8 mm (Six millimetre/Eight millimetre) thick hard wood edging. The shutter from out side shall to be finished with 1mm (One millimetre) thick lamination of Century / Greenlam / Action Tesa / Merinolam of approved shade including fixing Top PTMT handles 125mm (One hundred twenty five millimetre) long shall be provided in wood colour with nickel plated piano hinges including fixing with nickel plated piano hinges with screws etcetera. (Area for Payment shall be measured for front face only) complete as per architectural drawings specifications, design and as per the directions of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Cup-board shutter magnetic catcher with necessary screws etcetera complete as per architectural drawings specifications, design and as per the directions of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 65x35mm (Sixty five into Thirty five millimetres) size special quality chromium plated brass cup board lock with six leavers including necessary screws etcetera complete (Indian make approved quality) including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Stainless steel curtain rail with rollers stop ends and brackets in pelmets with curtain rod of 25 mm (Twenty five millimetre) diametre and brackets etcetra complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 300x16mm (Three hundred into Sixteen millimetres) nominal size aluminium sliding door bolts ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 250x16mm (Two hundred fifty into Sixteen millimetres) nominal size aluminium sliding door bolts ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium 250x10mm (Two hundred fifty into Ten millimetres) nominal size Tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera. complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium 150x10mm (One hundred fifty into Ten millimetres) nominal size Tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera. complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetres) nominal size aluminium Handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etcetera; complete including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 125mm (One hundred twenty five millimetres) nominal size aluminium Handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etcetera; complete including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 250mm (Two hundred fifty milimetres) size aluminum Hooks and Eyes PILOT/ Sheel or equivalant with necessary screws etcetera; complete including carriage of material within all leads, lifts and other. incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Aluminum Hydraulical door closer with necessary screws etcetera; complete including carriage of material within all leads, lifts and other. incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etcetera; complete including carriage of material within all leads, lifts and other. incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 19 mm (Nineteen millimetre) thick Chima thick Chima Pink Granite flooring in combonation with Black Granite as per pattern and detail laid over 20mm(Twenty millimetre) (average) thickness base of cement mortar 1:3 (One cement isto Three sand) and jointed with grey cement slurry mixed with pigment to match the shade of granite stone complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 18 mm (eighteen millimetre) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Baroda green marble slab having Semi Round nosing in work top of Pantary / under counter wash basin and water trough and similar locations of required size, approved shade, colour and texture laid over 20 mm (twqenty millimetre) thick base cement mortar 1:4 (one cement isto coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 600x 600mm (Six hundred into six hundred millimetre) Double Charge vetrified tiles of Restile /Nitco /Rak /Kajaria / Orient -Bell /AGL / Simpolo /Johnson / Somany of approved shade and design, in flooring laid on a bed of 20mm thick cement mortar 1:4 (One cement isto four sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying mirror polished 25 mm (twenty five millimetre) thick Kotah stone and white marble flooring minimum Size 55x55cm (fifty five into fifty five centimetre) in 70 : 30 (seventy isto thirty) ratio as per flooring pattern of approved shade as per detail slab flooring over 20 mm (twenty millimetre) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement isto four coarse sand)complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 300x300 mm (Three hundred into three hundred millimetre) size antiskid ceremic tiles of premium quality of grade-IV of Nitco/AGL / RAK / SIMPOLO / Kajaria / Somany / Orient Bell /Johnson tiles as per approved shade in flooring in cement mortar 1:3 (One cement isto Three sand) finished with flush pointing in white cement as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 1.8mm (one decimal eight millimetre) thick vinyl flooring over CC flooring, ISI marked IS No 3462/1986 of wonder / LG /Unitex floor of approved shade & Sample with approved adhesive on sub-floor (damp proofing treatment to be paid for separately) as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 40 mm (forty millimetres) thick cement concrete flooring 1:2:4 (One cement isto two sand into four graded stone aggregate 20mm (Twenty millimetres) nominal size) laid in one layer finished with a floating coat of neat cement complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 25 mm (twenty five millimetre) thick Kota stone in single piece with uniform nosing / edging in treads of same shade that of flooring of approved shade as per detail slab flooring over 20 mm (twenty millimetre) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement isto four coarse sand) complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying mirror polished 25 mm (twenty five millimetre) thick single slab Kota stone in risers of steps single piece of same shade that of flooring of approved shade as per detail slab flooring over 20 mm (twenty millimetre) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement isto four coarse sand) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 300x450mm (Three hundred into Four hundred fifty millimetre) size Ceremic Glazed tiles of Kajaria/ Nitco / Simpolo/Somany / Orient and Bell / AGL/Johnson in skirting risers of steps and dados (in attached toilets) with cement mortar 1:3 (One cement isto Three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 40 mm (forty millimetre) thick fine dressed red Mandana stone flooring over 20 mm (twenty millimetre) (average) thick base of cement mortar 1:5 (one cement isto five coarse sand), including pointing with cement mortar 1:2 (one cement isto two stone dust) with an admixture of pigment to match the shade of stone complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying Kota stone slabs 25mm (Twenty five millimetre) thick in risers of steps, skirting, dado and pillars laid on 12mm (Twelve millimetre) (average) thick cement mortar 1:3 (One cement isto Three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying Double Charge Vitrified tiles of Restile/Johnson/ Nitco/Kajaria / AGL / Simpolo / Somany /Orient & Bell as per approved shade and design of the office Size of Tile 600x600 mm (Six hundred into six hundred millimetre) size (thickness to be specified by manufacturer), with water absorption less than 0.08% (Zero point zero eight percent) and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm (Twelve millimetre) thick bed of cement mortar 1:3 (One cement isto Three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilogram per suare metre) including grouting the joint with white cement & matching pigments etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Cement plaster skirting up to 30 cm (thirty centimetre) height, with cement mortar 1:3 (one cement isto three coarse sand), finished with a floating coat of neat cement etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing staircase railing having 75x40mm (seventy five into forty millimetre) M.S. rectangular hollow section pipe hand rail and baluster of 19mmx19mm (nineteen into nineteen millimetre) and 12x12mm (twelve into twelve millimetre) M.S solid square bars in combination with M.S. flat 40mm x 6mm (forty millimetre into six millimetre) with a clear height of 85cm (eighty five centimetre) at 30 cm (thirty centimetre) centre to centre jonting in cement concrete steps. The vertical balusters to be welded /jonted with M.S hollow hand rail and applying a coat of red lead paint complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 40mm forty millimetre) diametre M.S. hollow pipe handrail of ramp, slip resisance with round ends at two level at 75 & 90 cm (Seventy five centimetre and Ninety centimetre) height cm height welded to 25 mm (Twenty five millimetre) diametre M.S. hollow pipe which is turn should be welded to balusters. It should extend 30 cm (thirty centimetre) beyond the top and bottom of the ramp as per detail. The balusters in ramp should be 50mm (Fifty millimetre) diametre M.S. hollow pipes embeded in cement concrete parapet at the rate 60mm (sixty centimetre) centre to centre intervals with 25mm (Twenty five millimetre) diametre M.S. hollow pipe moulded to shape as per drawing No 33 of Job nn 7704 complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 50mm (Fifty millimetre) diametre SST (Stainless steel) pipe of Kich handrail slip resistant in ramp at two level i e 75cm and 90cm (Seventy five centimetre and Ninety centimetre) height welded with 25mm (Twenty five millimetre) diametre M.S hollow pipe balusters embedded in cement concrete 60cm (sixty centimetre) centre to centre and jointing with electrical gas welding at top alongwith hand rail of hollow M.S. (Mild Steel) pipe of 50mm (Fifty millimetre) diametre. It should extend 30cm (Thirty centimetre) beyond top and bottom of the ramp complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing factory made ridges or hips having proper gola shape 60 cm (Sixty centimetres) overall with 0.60 mm (Zero point sixty millimetres) thick prepainted steel sheets of Tata / Sail / Reliance / Jindals steels in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating fixing with prepainted iron J or L hooks, bolts & nuts 6 mm (Six millimetres) diametre and prepainted G.I. limpet and bitumen washers complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing valley 90cm (Ninety centimetres) overall 0.60mm (Zero point sixty millimetres) thick prepainted steel sheet of Tata Durashine / Sail / Reliance / Jindals steels in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetres) dia with prepainted G.I. limpet and bitumen washers complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing prepainted steel sheet of Tata Durashine / Sail / Reliance / Jindals steels in roofing over steel trusses providng and fixing kelemetal or equivalent prepainted single skin trapezoidal profile sheeting 0.60 mm (Zero point sixty millimetres) thick having the 1060mm (one thousand sixty millimetre) cover width (overall width 1126mm (one thousand one hundred twenty six millimetre), 28mm (twenty eight millimetre) crest depth at 353+2 cenre to centre crest distance. there will be two ribs at the centre for stifferning having crest depth of 2.5mm (two decimal five millimetre) The mail crest width at top of 25mm (twenty five millimetre) and at lower 81mm (eighty one millimetre) base metal of cold rolled stel coil with zinc coating. The top coat with regular modified polyester coating of approved shade and balancing reverse coat with polyester paint fixing of sheet shall be of self drilling and self tapping screws of size 5.5mm (five decimal five millimetre) and 5.5mm (five decimal five millimetre) length with EDPM seal complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing minimum 30cm (Thirty centimeters) wide 30cm (Thirty centimeters) deep of 0.60mm (Zero decimal six zero milimetres) thick plain G.I. sheet gutter of TATA/ Sail/Reliance/Jindal with iron brackets 40x3mm (Forty into Three milimetre) size dome shape grating shall be provided which shall be M.S. plate 25x5/ 6mm (Twenty five into five/six millimetre) square round shape with 6mm (Six millimetres) diametre bars in dome including bolts and nuts and washers and including making necessary connections with rain water pipe complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing M.S. B.P. sheet 2.0mm (Two point zero millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured and paid separately) including fixing complete as per architectural drawings including carriage of material, within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing water proofing treatment shall be done in two coats apply First coat of Dr. Fixit Torch SHIELD (P-3160-3mm) to the clean and saturated surface maintaining a coverage 0.60 sqm (Zero point six zero squate meter) per kilogram to achieve 1mm (one millimeter) thickness this coating shall also be executed upto 300mm (Three hundred millimetre) vertically. The second coat shall be applied in opposite direction after 4 to 6 (Four to six) hours of application of 1st coat then sprinkle sand on top surface of applied Dr. Fixit Fast flex white still tacky and the second coat. Then apply cement mortar 1:4 (one cement ist four sand) and mixed with Pidiproof LW at the rate 200ml (two hundred millilitre) per 50 (Fifty kilogram) of cement over the floor with suitable gradient towords drain water pipe while the second coat of Dr. Fixit is still tacky complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing unplasticised PVC Pipe clips / Clamps of Supreme/Finolex/ Prince/Relpipe (reliance)vectus of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete including carriage of material within all leads, lifts and other incidentals. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 150 mm (One hundred fifty millimetre) diametre on wall face unplasticised Rigid PVC (D-Plast) rain water pipes single socketed conforming to IS : 13592 Type A ISI marked of Finolex/Relpipe (Reliance) /Vectus working pressure not less than 4/6 kg/cm2 (Four/Six kilogram per centimetre sqaure), including jointing with seal ring conforming to IS : 5382 including jointing with seal ring leaving 10mm (Ten millimetre) gap for thermal expansion including filling the joints with approved adhesive complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetre) Plain Bend on wall face PVC acessories for rain water pipes working pressure 4/6 kg/cm2 (Four/Six kilogram per centimetre sqaure) ISI marked of Finolex / Relpipe (Reliance)/Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetre) Plain Shoe on wall face PVC acessories for rain water pipes working pressure 4/6 kg/cm2 (Four/Six kilogram per centimetre sqaure) ISI marked of Finolex / Relpipe (Reliance)/Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Structural steel work of Tata / Sail / Reliance/Jindal riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing angle iron section 25x25x5 mm (twenty five into twenty five into five millimetre) thickness including hinges jamb, beads and if required angle thrashold of MS 25x25x5 mm (twenty five into twenty five into five millimetre) welded or rigidly fixed by mechanical means, lugs, with split and tails to each jamb including steel but hinges 2.50mm (two point five zero millimetre) thick with provision for locking arrangement and shock as specified and applying a coat of approved steel primer after pre treatment of the surface complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Smooth finishing of the exposed surface of Reinforced Cement Concrete work with 6mm (Six millimetre) thick cement mortar 1:3 (One Cement isto Three fine sand) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Acoustic wood wool perforated designer tiles in combination with perforated Acoustical Panel tiles ceiling of high sound absorption 0.90 (zero decimal nine zero) NRC in 60x 60 cm (sixty into sixty centimetre) grid within G.I. frame work of approved shade over 50mm thick absorb wool / insulation of Dexune / Himalayan as per detail as per pettern complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 600x600 mm (six hundred into six hundred millimetre) of approved texture, design and patterns having moisture content less than 2% (Two percent), humidity resistance of 99% (ninety nine percent), NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (eighty five percent) (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm (zero point thirty three millimetre) thick (galvanized @ 120 (at the rate one hundred twenty) grams per sqm including both sides) comprising of main-T runners of size 15x32 mm (fifteen into thirty two millimetre) of length 3000 mm (Three thousand millimetre), cross - T of size 15x32 mm (fifteen into thirty two millimetre) of length 1200 mm (twelve hundred millimetre) and secondary intermediate cross-T of size 15x32 mm (fifteen into thirty two millimetre) of length 600mm (six hundred millimetre) to form grid module of size 600 x 600 mm (six hundred into six hundred millimetre) , suspended from ceiling using galvanised mild steel items (galvanizing @ 80 (at the rate eighty) grams per sqm) i.e. 50 mm (fifty millimetre) long, 8 mm (eight millimetre) outer diameter M-6 dash fasteners, 6 mm (six millimetre) diametre fully threaded hanger rod upto 1000 mm (one thousand millimetre) length and L-shape level adjuster of size 85x25x2 mm (eighty five into twenty five into two millimetre) Galvanised iron perimeter wall angle of size 24x24x0.40 mm (twenty four into twenty four into zero point forty millimetre) of length 3000 mm (Three thousand millimetre) to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm (four hundred fifty millimetre) center to center and 40 mm (forty millimetre) long dry wall wood screws complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 595x595x6 mm (Five hundred ninety five into fiive hundred ninety five into six millimetre) ACP ceiling with pre-painted GI channel framing @ 600 mm c/c (Six hundred millimetre centre to centre) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Wooden Penelling of 600x1200x25 mm( six hundred into twelve hundred into twenty five millimeters) fixed with steel screw complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 240x120 cm (two hundred forty into one hundred twenty) Black board having 12mm (twelve millimetre) thick green chalk board (non megnetic) with superior quality framing & square clamps fixed with the help of nylon sleves & screws as per site requirments . The board shall be fixed on the wall with specially designed j clamps. Blackboard shall have backing material of galvanized sheet 28mm (twenty eight millimetre) thick with top green surface for smooth writing with chalk over 11 mm (eleven millimetre) thick particle board. The board surface shall be non porus ceramic particles on the specially anodized aluminium Profile 20x15mm (twenty into fifteen millimetre) with corners of black plastic etcetra complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting two or more coats (including priming coat) with Nerolac/Asian paint on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting two coats (including priming coat) on over new wood and wood based surfaces with enamel paint of Nerolac/ Asian brushing to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 6mm (Six millimetre) thick cement plaster to ceiling in cement mortar 1:3 (One cement isto Three sand) upto all floor levels complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 15mm (Fifteen millimetre) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering including making groove or drip course, arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto Six sand) upto floor all levels complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering including making groove or drip course, arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto Six sand) above plinth level to floor all levels complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for exterior plastering including making groove or drip course, arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:5 (One cement isto Five sand) above plinth level to floor all levels complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying 20 mm (twenty millimetre) cement plaster in two coat backing coat 10 mm (ten millimetre) and finishing coat 10 mm (ten millimetre) thick on fair side of brick/stone masonary walls for interior plastering up to floor two level including aamses internal rounded angle chamfers and or rounded angle. Cement mortar 1:4 (one cement isto four sand) including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Forming groove of uniform size 15mm (Fifteen millimetre) wide and 15mm (Fifteen millimetre) deep groove in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing decorative screen in coridor manufactured from 19mm x 19mm (nineteen into nineteen millimetre) hollow square pipes welded with M.S. hollow sections of size 50mm x 50mm (fifty into fifty millimetre), supported on 10 cm (ten centimetre diametre) M.S. hollow pipes. A centre piece shall be of 25 x 3mm (twenty five into three millimetre) M.S. flat frame covered with M.S. black sheet made to shape and applying a priming coat of approved steel primer using structural steel as per approved specifications, drawing, design, as per entire satsfaction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing Plinth protection with 40 mm (Forty millimetres) thick interlocking paver blocks of NTC with 23cm (Twenty three centimetres) diametre Half round reinforced cement concrete pipe for drainage purpose fixed over 10cm (Ten centimetres) thick cement concrete 1:4:8 (One cement isto four sand isto eight graded) stone aggregate bedding complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Applying Birla / J.K. white wall care putty over plaster surface after thoroughly brushing the surface free from mortar dropings, dust, loose material and other foreign matters, sand papered smooth to give final matt finish to the surface upto floor all level complete including carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Finishing walls with exterior emulsion of Asian / Dulux / Berger / Nerolac Suraksha paints of approved shade having VOC less than 50 gm/litre (Fifty gram per litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives New work (Two or more coats applied @ 1.43 litre/ 10 sqm (One point forty three litre per ten square metre) over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (Zero point ninety litre per ten square metre) upto all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting Two or more coats on new work with synthetic enamel paint of Asian Paint / Nerolac Paints to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for matting the surface smooth upto all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Distempering with 1st (first) quality synthetic / acrylic washable distemper of Asian Paint / Nerolac Paints, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Expension joint system related with wall joint (internal and external) location as per drawing and direction of Engineer-in Charge. The joint shall be filled with polysterence back or rod base member self alinging /centering arriangement and support. The material shall be such that it provides as expension joint system suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office building and complexes with no slipping down tendancy amongest the component of the joint system shall be filled with sealent of Dr. Fixit/Pedelite C.I. Co. T-680. The joint shall utilize light weight with polysterence back or rod surfaces mechanically snap locking multicelluar to facilitate movement complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying plain cement concrete 1:2:4 (One cement isto Two sand isto Four graded broken/crushed stone aggregate 20mm (Twenty millimetre) nominal size mechanically mixed vibrated and curing complete excluding cost of forms work in foundation and plinth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 60mm (Sixty millimetre) thick factory made cement concrete interlocking paver block of NTC / Unistone / Atlantic vibro compacted upto M-50 (M-fifty) grade including border or kurb block grey or coloured over sub-base of concrete with 25mm (Twenty five millimetre) thick average thickness of cement mortar 1:4 (One cement isto Four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing and polishing complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:3:6 (One cement isto Three sand isto Six graded stone aggregate 40mm (Forty millimetre) nominal size and curing complete excluding cost of form work in foundation and plinth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Applying cement slurry on Reinforcement Cement concrete slab or cement concrete work using 2.75 kgs. (Two point seventy five Kilogram) Of cement per square meter of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and filling broken/ crushed stone/ brick bats of hard stone of 40 mm (forty millimetre) size in soak pit complete with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 1620 20mm (Twenty millimetres) Outer diameters Polyethelene-Aluminium / Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450 ,2004 of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetera, with clamps at 1.00 (One) metre spacing for concealed work including cutting chases and making good the wall etcetera. This includes testing of joints complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 2025 25mm (Twenty five millimetres) Outer diameters Polyethelene-Aluminium / Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450 ,2004 of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetera, with clamps at 1.00 (One) metre spacing for concealed work including cutting chases and making good the wall etcetera. This includes testing of joints complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40mm (Twenty millimetre to forty millimetre) nominal bore by providing and fixing tees including cutting and threading the pipe complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal bore/diametres High pressure PVC waste and ventilating having pressure pipes 4.00 kg/cm2 (Four point zero zero kilogram per centimetre square) of Finolex/ Vectus/Relpipe (Reliance) including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal bore/diametres High pressure PVC waste and ventilating having pressure pipes 4.00 kg/cm2 (Four point zero zero kilogram per centimetre square) of Finolex/ Vectus/Relpipe (Reliance) including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal bore/diametres P.V.C clamps ISI marked of Finolex/Relpipe (Reliance)/Vectus etcetera including finishing with approved design with steel screws and rawal plugs etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal size P.V.C clamps ISI marked of Finolex/Relpipe (Reliance)/Vectus etcetera including finishing with approved design with steel screws and rawal plugs etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal bore/diametres PVC Finolex/Relpipe(Reliance)/Vectus Heal Rest Confirming to BIS-14735-99 including filling the joints with approved adhesive complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal size PVC Finolex/Relpipe(Reliance)/Vectus Heal Rest Conforming to BIS-14735-99 including filling the joints with approved adhesive complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC plain bend of required degree ISI marked Conforming to BIS-14735-99 of Finolex/Relpipe (Reliance)/Vectus insertion rubber washer 3 mm (Three millimetre) thick bolts and nuts complete including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal size PVC plain bend of required degree ISI marked Conforming to BIS-14735-99 of Finolex/Relpipe (Reliance)/Vectus insertion rubber washer 3 mm (Three millimetre) thick bolts and nuts complete including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC Collar of ISI marked Conforming to BIS-14735-99 of Finolex/Relpipe(Reliance)/ Vectus including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal size PVC Collar of ISI marked Conforming to BIS-14735-99 of Finolex/Relpipe(Reliance)/ Vectus including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC Cowl of ISI marked Conforming to BIS-14735-99 of Finolex/Relpipe(Reliance)/ Vectus including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal size PVC Cowl of ISI marked Conforming to BIS-14735-99 of Finolex/Relpipe(Reliance)/ Vectus including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110x90mm (One hundred ten into nineteen millimetres) nominal size/diameter PVC floor trap ISI marked Finolex/Relpipe(Reliance)/ Vectus Conforming to IS-14735-99 of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the

Providing and fixing 110x75mm (One hundred ten into seventy five millimetres) nominal size/diameter PVC floor trap ISI marked Finolex/Relpipe(Reliance)/ Vectus Conforming to IS-14735-99 of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the

Providing and fixing white vitreous china pedestal type water closet (European type)No 20087 (S - 10 ) Size 57x 35x39cm (Fifty seven into thirty five into thirty nine millimetre) nominal size with seat and lid, 10 litre (Ten) low level white PVC flushing cistern (sleek Plus) having dual flush system of Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings and C.I. brackets, 40 mm (Forty millimetre) flush bend 20mm (Twenty millimetre) over flow pipe with seat & lid fixed with C.P. brass hinges and rubber buffers,with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and and fixed with jet pressure and intergal P or S trap including jointing the trap and soil pipe with adhesive of approved brand. (Jet Spray to be measured and paid for separately) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing water closet squatting pan (Indian type W.C. pan )White Vitreous china Orissa pattern W.C. pan no 20090 of size 530x410 mm (Five hundred thirty into Four hundred ten millimetre) with integral type foot rests with 100 mm (One hundred millimetre) diametre sand cast Iron P or S trap, 10 litre (Ten) low level P.V.C. flushing cistern having dual flush system of Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetre) diametre P.V.C. flexible waste pipe of Finolex/ Relpipe (Reliance) / Vectus for sink or wash basin including P.V.C. waste necessary fitting complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing G.I. inlet connection for each flush pipe with W.C. pan including necessary fitting complete including entire carriage of material complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china wash basin garnet No-10080 Cera / Hindware Jaguar/Snow white/star white shade 58x43cm (Fifty eight into forty three centimetres) under counter basin with single hole for pillar tap including 15mm (Fifteen millimetre) diametre Pillar Tap with C.I. or M.S. brackets painted white including cutting holes and making good the same with pedestal but excluding fittings including neccessary fitting complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing wash basin White Vitreous China Flat back wash basin Delta No 10010 size 550x 400 mm (Five hundred fifty into four hundred millimetre) (Under counter Basin ) Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details with single 15 mm (Fifteen millimetre) C.P. brass pillar tap with C.I. brackets, 15 mm (Fifteen millimetre) C.P. brass pillar taps, 32 mm (Thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing white vitreous china flat back range of two half stall urinal Large flat back no 60002 of size 39x37.5x59cm (Thirty nine into thirty seven point five into fifty nine centimentre) with white PVC automatic flushing cistern of Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details with ittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required with 10 (Ten) litre P.V.C. automatic flushing cistern including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and Fixing Charomium plated 40mm (forty millimetres) diametre steel pipe for grab bars at 78cm (seventy eight centimetres) height metres M.S. plate as per details at the position of the seat and Wash Basin complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal type Matrix water closet (European type) with seat and lid, 10 litre (Ten) low level white PVC flushing cistern (sleek Plus) having dual flush system of Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings & C.I. brackets, 40mm (Forty millimetre) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid each including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing White Vitreous China Flat back Matrix wash basin 550x400mm (Five hundred fifty into Four hundred millimetre) of Cera / Hindware / Jaquar with single 15mm (Fifteen millimetre) C.P. brass pillar tap with C.I. brackets, 32mm (Thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Stainless Steel kitchen sink with drain board of Diamond/Unik/ Preyag big size 610x510x200 mm (Six hundred ten into five hundred ten into two hundred millimetres) including C.P. waste with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimeter) nominal size / diameters M.I. union for wash basin or sink including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore P.V.C. connection pipe with brass union 45cm (Forty five Centimeters) length complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Mixer for kitchen sink with casted swinging spout at top ISI marked IS No 8934 of Jal /ESS including neccessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimeter) nominal size diameters C.P. waste for wash basin or sink including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing two hole basin mixing Faucet of ISI marked IS No 8934 of Jal /ESS including neccessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government..

Providing and fixing 100mm (One hundred millimetres) diametre C.P. iron grating of Superior quality of ISI marked IS No 8934 of Jal /ESS for floor, gully or Nahni trap including neccessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government..

Providing and fixing 75mm (Seventy five millimetres) diametre C.P. iron grating of Superior quality of ISI marked IS No 8934 of Jal /ESS complet for floor, gully or Nahni trap including neccessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government..

Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty millimetres) beveled edge mirror of ISI marked IS No 8934 of Jal /ESS of superior glass (of approved quality) complete with 6mm (Six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x20mm (Six hundred into twenty millimetres) size CP Brass towel rail of ISI marked IS No 8934 of Jal /ESS complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour including neccessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Plastic Liquid soap container with C.P. brass lid and brackets fixed to wooden plugs with C.P. brass screws including neccessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing C.P. Brass toilet paper holder (Heavy duty) ISI marked IS No 8934 of Jal /ESS including neccessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 8mm (Eight millimetre) diametre C.P./Sstainless steel Jet of ISI marked IS No 8934 of Jal /ESS with flexible tube upto 1 (One) metre long with S.S. triangular plate to Eureopean type W.C. of quality make and approved quality complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x120x5mm (Six hundred into One hundred twenty into five millimetres) glass shelf of ISI marked IS No 8934 of Jal /ESS with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm (Fofrty millimetre) long screws, rawl plugs etcetera including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetre) diametre C.P. brass. Bib tap of fancy tap No 12 of approved quality and colour of prayag polymet symet bath assets or its equivalent complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15 mm (Fifteen millimetre) nominal bore C.P. brass stop cock (concealed) of ISI marked IS No 8934 of Jal /ESS including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetre) nominal bore C.P. brass angle valve of of ISI marked IS No 8934 of Jal /ESS including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15 mm (Fifteen millimetre) nominal bore C.P.push cock of ISI marked IS No 8934 of Jal /ESS without nuts and pipes including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore/diametre brass full way valve with wheel of ISI marked IS No 8934 of Jal /ESS without nuts and pipes including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore C.P. brass valve (Horizontal plunger type) High pressure with polythene plastic floats of of ISI marked IS No 8934 of Jal /ESS or its equivalent complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC single equal branch with oval access door, ISI marked of Finolex/Relpipe (Reliance)/Vectus insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75 mm(Seventy five millimetre) nominal size PVC single equal branch with oval access door, ISI marked of Finolex/Relpipe (Reliance)/Vectus insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC double equal branch with oval access door, ISI marked of Finolex/Supereme/Relpipe (Reliance)/Vectus insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal size PVC double equal branch with oval access door, ISI marked of Finolex/Relpipe (Reliance)/Vectus insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC door bend with oval access door, insertion rubber washer 3mm (Three millimetre) thick ISI marked of Finolex/Relpipe (Reliance)/Vectus complete including fixng with approved adhesive etcetera complete in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75 mm(Seventy five millimetre) nominal size PVC door bend with oval access door, insertion rubber washer 3mm (Three millimetre) thick ISI marked of Finolex/Relpipe (Reliance)/Vectus complete including fixng with approved adhesive etcetera complete in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC Finolex/Relpipe (Reliance)/Vectus offset 45° (Forty five degree) ISI marked including fixing with approved adhesive and necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75 mm(Seventy five millimetre) nominal size PVC Finolex/Relpipe (Reliance)/Vectus offset 45° (Forty five degree) ISI marked including fixing with approved adhesive and necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and placing on terrace (at all floor levels polyethylene water storage tank, tripple layer of Finolex/Relpipe (Reliance)/Vectus IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank ccomplete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (One cement isto Five sand isto Ten graded crushed stone aggregate 40mm (Forty millimetres) nominal size in all round for PVC pipe of 150mm (One hundred fifty millimetres) internal diametre including bedding necessary form work and curing ccomplete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one point five coarse sand (zone- III) isto three graded crushed stone aggregate 20 mm (Twenty millimetres) nominal size), foundation concrete 1:4:8 mix (one cement isto four coarse sand (zone- III) isto eight graded stone aggregate 40 mm (Forty millimetres) nominal size), inside plastering 12 mm (Twelve millimetres) thick with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate 20mm (Twenty millimetre) nominal size finished with floating coat of neat cement complete as per standard design Inside size 90x80 cm (Ninety into eighty centimetres) and 45 cm (Forty five centimetres) deep including C.I. cover with frame (light duty) 455x610 mm (Four hundred fifty five into six hundred ten milimetres) internal dimensions, total weight of cover and frame to be not less than 38 kg (Thirty eight kilogramme) (weight of cover 23 kg (Twenty three kilogramme) and weight of frame 15 kg (Fifteen kilogramme)) With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one point five coarse sand (zone- III) isto three graded stone aggregate 20 mm (Twenty millimetres) nominal size), foundation concrete 1:4:8 mix (one cement isto four coarse sand (zone- III) isto eight graded crushed stone aggregate 40 mm (Forty millimetres) nominal size), inside plastering 12 mm (Twelve millimetres) thick with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded crushed stone aggregate 20 mm (Twenty millimetres) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90 cm (One hundred twenty into ninety centimetres) and 90 cm (ninety centimetres) deep including C.I. cover with frame (medium duty) 500 mm (Five hundred millimetres) internal diameter, total weight of cover and frame to be not less than 116 kg (One hundred sixteen kilogramme) (weight of cover 58 kg (Fifty eight kilogramme) and weight of frame 58 kg (Fifty eight kilogramme)) : With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (one cement isto four coarse sand) C.I. cover with frame (light duty) 455x610 mm (Four hundred fifty five into six hundred ten millimetres) internal dimensions, total weight of cover with frame to be not less than 38 kg (Thirty eight kilogramme) (weight of cover 23 kg (Twenty three kilogramme) and weight of frame 15 kg (Fifteen kilogramme)), R.C.C. top slab with 1:1.5:3 mix (one cement isto one point five Fine sand isto three graded stone aggregate 20 mm (twenty millimetres) nominal size), foundation concrete 1:5:10 (one cement isto five fine sand isto ten graded stone aggregate 40 mm (Forty millimetres) nominal size), inside plastering 12 mm (Twelve millimetres) thick with cement mortar 1:3 (one cement isto three coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etcetera complete as per standard design Inside dimensions 455x610 mm (Four hundred fifty five into six hundred ten millimetres) and 45 cm (Forty five centimetres) deep for single pipe line With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five centimetres) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x300mm (Six hundred into Thre hundred millimetres) nominal size of Division Plate for Urinals Hindware /cera/Jaquar of star white / snow white shade and (Heavy duty make ISI marked No- 8931 & 8934) of approved quality and colour complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 20 mm (Twenty millimetre) nominal bore in trenches, galvanised mild steel tubes (medium grade) with G.I fittings including trenching and refilling etcetera complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) nominal bore to wall ceiling and floor galvanised mild steel tubes (Medium grade) ISI make approved quality tube fitting and clamps including making good the wall, ceiling and floor complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 150mm (One hundred fifty millimetre) nominal bore/diameter (to level or slopes) PVC pipe grade 'A' and jointing with approved adhesive ncluding testing of pipes and joints complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 455x610mm (four hundred fifty five into six hundred ten millimetre) light duty rectangular C.I. manhole with frame cover weight 38KG (thirty eight kilograms) (single seat) complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing of water lifting pump of 1.00 HP (One point zero horse power) of serex/Kirloskar/Crompton/Wortington including all necessary fittings complete in all respect including entire carriage of materials within all leads lifts and other incidentals, and as per specification and as per directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 20x20 mm (twenty into twenty millimetre) square bar M.S Foot rest including fixing in man holes with 20x20x10 Cm (twenty into twenty into ten centimetre) cement concrete 1:3:6 (one cement isto three sand isto six graded /crushed stone aggregate) 20 mm (twenty millimetre) nominal size as per standard design within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.