COMPREHENSIVE REPAIRS TO MARRIED ACCN OF YADUNATH VIHAR AND YOGENDRA ENCLAVE AT AGE B R I UNDER GE (SOUTH) AMBALA CANTT

Amount

Material and labour for cleaning the roof top surfaces, brick tiles or concrete surfaces by picking vegitation roots, sweeping clean and washing down with water to remove dust etc and filling the damaged joints of brick tiles in CM 1:4 complete all as specified and directed.

Material and labour for preparation of roof surface and providing 40mm thick average thickness PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in roof padding, levelling course and finishing top surfaces even and smooth without using extra cement to receive APP membrane etc, complete all as specified and directed.

Material and labour for preparation of roof top surface, providing and applying PU based waterproofing and heat reflecting system having properties UV resistant and resistant to yellowing and weathering, high elastic and crack bridging, non-toxic and VOC compliant water based coating, single component ready to use, water vapour permeable having solid content 60% (ASTM D 1644), density 1.30 gm/cc, 350% elongation, tensile strength 2.8 to 2.9 N/sqmm and solar reflective index 100. The material is applied as follows- (a) Applying primer over prepared surface with Homeshield PU roofkoat of Make Berger or equivaent as approved by GE. The material and water in 1:1 ratio by weight having total thickness 0.4 to 0.5mm, glass fibre reinforced and consumption 0.25 kg per sqm. The surface shall be cured for 2-4 Hrs depending on climatic conditions. (b) Applying second coat with Homeshield PU roofkoat of Make Berger or equivaent with consumption 0.50 kg per sqm. The surface shall be cured for 12 Hrs depending on climatic conditions. (c) Applying final coat with Homeshield PU roofkoat of Make Berger or equivaent with consumption 0.50 kg per sqm. Note : (i) The entire work shall be executed through authorized applicator of approved make and gurantee of waterproofing shall be 10 years. (ii) Performance gurantee of amount @5% of waterproofing treatment shall be submitted by contractor for period of 10 years.

Material and labour for PCC Type B-1 1:2:4 (using 12.50 mm graded aggregateas) as in roof kerbs of mud stops, rounded or chamfered on edges including dismantling of existing PCC complete all as specified and directed.

Material and labour for preparation of old decorative surface of wall etc by washing rubbing down including scrapping and applying one coat of cement base paint of any tint complete all as specified and directed.

Material and labour for preparation of old decorative surface of wall including washing rubbing down and stopping of distempered and painted surfaces and applying one coat of oil emulsion paint complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surface of walls by using appropriate technique as approved by Engineer-in-Charge for complete removal of all layers of treatment and reaching upto old plastered surface and applying a coat of wall care putty not less than 1mm thick as per manufactures's instructions and applying two coats of oil emulsion paint over a coat of alkali primer complete all as specified and directed.

Material and labour for preparing old plastered surfaces of walls and applying one coat of white wash complete as all specified and directed.

Material labour for Preparation of old treated surfaces (Plastered or un-plastered) of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts, trading oil and greasy spots etc. and applying one coat of white wash on ceiling, complete all as specified and directed.

Material and labour for preparation of old wood and wooden based surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surfaces, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

Material and labour for 5mm thick rendering in cement mortar in 1:3 as in ceiling surface and finished the surface even and smooth without using extra cement including preparation of new plastered surface and applying three coat of white wash complete all as specified and directed.

Demolition of lime concrete or cement conrete of any description and in any position as of sunken portion complete all as specified and directed.

Demolition of Cement Concrete as in ground floor and paving not exc. 15cm thick (above or below G.L.) complete all as specified and directed.

Material and labour for 50 mm thick PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in plinth protection finished fair and even without using extra cement complete all as specified and directed by Engineer-in-charge. Note:- The plinth protection shall be laid in panels and length of each panel shall not be more than 2.00 m and 6mm joints filled with 85/25 grade bituman and sand in the ratio (1:3) shall be provided.

Material and labour for rendering 10 mm thick in CM 1:3 and mixed with and including integral waterproofing compound @ 3% by weight of cement and applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning of surface complete all as specified and directed.

Material and labour for plain cement concrete type E2 1 : 5 :10 (using 40 mm graded aggregate) in foundations, filling and mass concrete as in sunken floor complete all as specified and directed.

Material and labour for plain cement concrete type C2 1 : 3 :6 (using 40 mm graded aggregate) in foundations, filling and mass concrete as in under sunken floor complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-Charge.

Material and labour for brick work with, built in CM 1:6 sub class 'B' (old size) bricks, straight or curved on plan, exceeding 6 mtr mean radius etc complete all as specified and directed.

Material and labour for brick work built in CM 1:6 straight or curved on plan exceeding 6 metre mean radius using sub class ‘B’ bricks (Except bricks) complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in copings, benching, kerbs, edges etc including necessary form work complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar 1:4 including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar 1:4 including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality coloured glazed ceramic tiles 300mm x 450mm x 7 to 8mm thick) as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the shade of tiles over and including rendering 10mm thick in cement mortar 1:3 finished rough surface to receive tiles including dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for 15 to 18 mm thick Granite stone of black shade work (table rubbed, polished and moulding), as in floors, cooking platforms and like bedded with and including 15 mm thick screed bed in CM 1:4 and jointed with grey cement slurry @ 3 Kg/Sqm, and pointed with white with admixture of pigment to match with shade of granite stone including grinding and polishing including dismantling of existing stone slabs including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for 15 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, skirting, on vertical surface and like in 10mm thick rendering in CM 1:3 and jointed with grey cement slurry @ 3 Kg/Sqm, and pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including rounding, moulding and polishing on edges etc including dismantling of existing stone /tiles etc including cement mortar bedding and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar 1:4 including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar 1:4 including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Supply and fixing heavy duty tiles (coloured),good grip series,size 400 mm x 400 mm x 10 mm thick ,pattern as approved by Engr - in - Charge ,set , jointed and pointed in neat cement slurry @ 3 kg/square metre ,laid over and including 20mm thick (average thickness) cement mortar (1:4) bed complete all as specified and directed by Engineer- in - Charge . (Note: Design/pattern shall be as approved by GE/Engr -in-Charge at the time of execution)

Supply and fixing (in repair) of vitreous china wash hand basin white flat back of size 550x440mm including CI brackets and 15mm chromium plated pillar tap cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, PVC connection 450 mm long having PTMT nuts and chromium plated waste coupling and making good the disturbed portion including 32 mm dia PVC waste pipe etc., complete all as specified and directed.

Supply and fixing in repair of vitreous china wash down water closet pedestal pattern (EWC), White including connection to trap and to flushing pipe with ‘P’ or ‘S’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible LDPE pipe jointed with pipe complete all as specified and directed.

Supply and fixing in repair of vitreous china squatting pan of orrisa pattern size 580 x 440 mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and foot rests of any pattern complete including provision of cement concrete bed and connection to flush pipe excluding flushing cistern, flush pipe and bracket and making good the disturbed area complete all as specified and directed.

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre and not exceeding 4.00 Square metre each (without taking off shutters from frames) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM 1:3 and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down chowkats or frames with shutter, area not exceeding 1.50 Square metre (without taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM 1:3 and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down old unserviceable wooden shutter of any descritption exceeding 1.00 sqm each but not exceeding 2.00 sqm each and removal from site including iron mongry, complete all as specified and directed.

Material and labour for taking down shutter of any description exc 1.00 sqm but not. exc 2.0 each and refixing in same opening after necessary repair/easing and adjusting complete all as specified and as directed.

Supply and fixing Factory Made Single Extruded WPC (Wooden Polymer Composite) Solid color Board 18mm Thick comprising of virgin polymer of K Value 58-60 (Suspension Grade), Calcium Carbonate and Natural Fibers (Wood Power / Rice Husk [Wheat Husk) and Non-Toxic Adhesives (Maximum Toxicity index of 12 for 100 gram) having minimum density of 650 Kg/ CUM and Screw withrawal strength 1800 N (face) and 900 N (Edge), Minimum Compressive strength 50 N/ mm 2. Modulus of elasticity 850 N / mm Sq and Resistance to spread of flame of class A category with property of being termite/ borer proof, Water Proof/ Moisture Proof and Fire Retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws including taking down of existing board of any type all as per direction of Engr in Charge.

Supply and fixing for lipping 1-1.5 mm thick 18 mm wide of approved design and color , fixed with solvent cement or head less nails to PVC door complete all as specified and directed

Supply and fixing continous (Piano) type hinges of mild steel bright finish or electro galvanised with width of flaps 40mm complete all as spd and directed.

Supply and fixing 100 mm size hasp and staple,safety type,Stainless steel bright finish ,including bolt to hinge plate and fixed with screws, complete all as specified and directed.

Supply and fixing of stainless steel barrel tower bolts of 100mm long complete all as specified and directed.

Supply and fixing of stainless steel handles of size 100 mm long complete all as specified and directed.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows and other Frames/ Chowkhat of size 50mm x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with including MS hold fast/ lugs/SS dash fasteners of required dia and length as per site requirement complete as per direction of Engineer-in-Charge. ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.

All as per above item No. 45.00 here in before but size 65x100mm complete all as specified and directed.

All as per above item No. 45.00 here in before but size 65x125mm complete all as specified and directed.

Supply and fixing 100mm long stainless steel butt hinges complete all as specified and directed.

Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid coloured both side laminated flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) and 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately)

Supply and fixing Factory Made 30mm thick 100% Solid WPC ( Wood polymer Composite ) solid coloured both side laminated Wiremesh Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cum manufactured by Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) and 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. For fixing Mosquito mesh and XTN aluminium mesh combinly panel area of door except stiles and rails to be panelled with mesh with self tapping round headed scresws at required distance, scres and edges covered with feathered pvc edge beading all around of mesh and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge. Material test certificate and authentication should be compulsory provided by the manufacturing company : For Internal/Balcony/Main Doors.

Supply and fixing of stainless steel barrel tower bolts of 150mm long complete all as specified and directed.

Supply and fixing of stainless steel handles of size 150 mm long complete all as specified and directed.

Supply and fixing of 250 mm stainless steel sliding door bolt, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet complete all as specified and as directed.

Material and labour for factory made box type steel windows with pressed steel frame complete including mild steel acessories like lugs, door stopper, holdfasts, pintol hinges, handles( minimum One for each shutter), and tower bolt 150mm size (minimum 2 for each shutter) etc. with or without glazing bars dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Window Fabrication shall be as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 and these drgs may be referred from GE office. (ii) Mode of measurement Unit will be in Kilogram for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery and Grill/ Guard bar complete as per TD. The weight of windows will be finalized by the BOO to be convened by GE. The weight shall not include PCC back filling of the chowkhat. (iii) The PCC back filling in chowkhat of window, Sheet glass and wire gauge will be measured and paid separately against respective items.

Supply and fixing in repair factory made steel ventilator with top hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars including PCC 1:3:6 type C-O, (using 12.5 graded aggregates) bed blocks for hold fasts if required all as specified and directed by Engineer-in-charge.

All as per item No-55.00 here in before but as in ventilator top hanging shutter without glazing bar including PCC 1:3:6 type C-O (using 12.5 graded aggregates) bed blocks for hold fasts if required all as specified and directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-charge.

Supply and fixing Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair drapery curtain rod, mild steel, powder coated 25mm dia with brackets, knobs, end stops etc complete all as specified and directed by Engineer - in - Charge .

Supply and fixing for sheet glass 4mm thick, pin headed type and glazing with oil putty or wooden beads in square not exc 0.5 Sqm in each pane complete all as specified and directed by Engr-in-Charge.

Supply and fixing stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutters complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutters complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair of sheet glass 4 mm thick, ordinary quality and glazing with oil putty, in square not exceeding 0.5 Sqm each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed . NOTE:-Glass will be fixed up to 12 Mtr height bldgs.

Supply and fixing in repair of 4 mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sq. m in each pane with oil putty or fixed with beads complete all as specified and directed. NOTE:-Glass will be fixed up to 12 Mtr height bldgs.

Material and labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar 1:6 on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement including preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over and including 1mm thick birla wall putty , complete all as specified and directed.

Material and labour for 15mm thick rendering in cement mortar 1:4 on surface of any description of brick or concrete and finished the surface even and fair without using extra cement with and including two coats of cement base paint over a coat of alkali primer complete all as specified and as directed.

Material and labour for rough cast plaster with and including 15mm thick rendering in CM 1:3 on brick wall or concrete surface as specified in clause 14.22 of SSR Part-I complete all as specified and directed. Note:-(i)After applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. (ii)The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered.

Supply and fixing in repair of PVC (SWR) floor trap, plain with grating including jointing with solvent cement of outer dia metre outlet of 75 mm complete all as specified and directed.

Supply and fixing PVC (SWR) 110 mm pipe type A single socket in any length with rubber ring joints fixed to walls including dismantling of existing pipes of any description any length complete all as specified and as directed.

Supply and fixing PVC (SWR) 75 mm pipe type A single socket in any length with rubber ring joints laid in floors or trenches including dismantling of existing pipes of any description any length complete all as specified and as directed.

Supply and fixing 110mm dia stack clamps made out of 50mm by 5mm flat iron and 16mm dia around iron stays,including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Supply and fixing in repairs of PVC (SWR) bends 110 mm bore complete all as specified and as directed.

Supply and fixing in repairs of PVC (SWR) bends 75 mm bore complete all as specified and as directed.

Supply and fixing in repairs of 110 mm bore PVC (SWR) junction single T (equal or unequal), including jointing with solvent cement, complete all as specified and directed.

Supply and fixing in repairs of 75 mm bore PVC (SWR) junction single T (equal or unequal), including jointing with solvent cement, complete all as specified and directed.

Supply and fixing in repairs of 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed.

Supply and fixing in repairs PVC waste pipe for wash hand basin / kitchen sink of dia 32/40 mm of required length at site complete all as specified and as directed.

Supply and fixing in repair of 75/100 mm dia CP grating with /without hole as per site requirement fixed in floor and jointed in CM 1:3 complete all as specified and as directed.

Supply and fixing in repair of stop valves, 15 mm dia, chromium plated, fancy type, screwed down, high pressure with capstain head, (concealed type) with long shank, screwed both ends for iron pipes or for unions, complete all as specified and directed. (Note : Weight of stop valve shall not be less than 0.575 Kg)

Supply and fixing in repairs 15mm bore CP Angle cock chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair of 15 mm dia long body chromium plated bib taps, cast copper alloy with flange complete all as specified and directed.

Supply and fixing door seal PVC 30mm wide with foam complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair of flush pipes to pedestal pan, including all joints complete all as specified and as directed.

Supply and fixing in repair of Chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union with shower arm complete all as specified and as directed.

Supply and fixing Stainless steel plate rack standard size 600mm x 750mm X 250mm of wt not less than 5 kg each of sheet thickness not less than 1.25mm of grade 304 complete and fixing with rawl plug and steel screws including taking down old plate rack of any size where exist , complete all as specified and directed.

Supply and fixing of GI tubing, 15mm bore, medium grade, with all fitting to walls and ceilings or laid in floors including necessary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing where ever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing of GI tubing, 20mm bore, medium grade, with all fitting to walls and ceilings or laid in floors including necessary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing in repair Chlorinated PVC (CPVC) pipes 20 mm outer dia, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1.0 m spacing . this includes jointing of pipe with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed.

Refixing old serviceable steel water tubing of 15 mm bore, in new or old position, any grade, including Supply and fixing new fittings as required, fixed to walls and ceilings or laying in floors including necessary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing where ever required including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Refixing old serviceable steel water tubing of 20 mm bore, in new or old position, any grade, including Supply and fixing new fittings as required, fixed to walls and ceilings or laying in floors including necessary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc from existing water storage tanks of capacity exceeding 250 litres and not exceeding 500 litres by emptying, drying and cleaning the tank by scrubbing the dust with wire brush from tank including cleaning from mouths of circulating pipes, to entire satisfaction of Engr-in–chargeof cleaning , including writing date of cleaning with oil paint of visible colour in font size not less than 100 mm, complete all as specified and directed (The rates includes for disconnecting of existing water tank, lowering if required and hoisting, reconnecting and refixing in same position after cleaning ) NOTE: - (i) The whole process of disconnecting, reconnecting and refixing in same position after cleaning shall be done on the same day, if failing so, Rs. 100/- shall be deducted for each tank per day from the contractor due. (ii) A separate register to be maintained by contractor for cleaning and occupant signature with date to be obtained in it.

Cleaning and removing all scale and dirt, etc from existing water storage tanks of capacity exceeding 500 litres and not exceeding 1000 litres by emptying, drying and cleaning the tank by scrubbing the dust with wire brush from tank including cleaning from mouths of circulating pipes, to entire satisfaction of Engr-in–charge of cleaning , including writing date of cleaning with oil paint of visible colour in font size not less than 100 mm, complete all as specified and directed (The rates includes for disconnecting of existing water tank, lowering if required and hoisting, reconnecting and refixing in same position after cleaning ) NOTE: - (i) The whole process of disconnecting, reconnecting and refixing in same position after cleaning shall be done on the same day, if failing so, Rs. 100/- shall be deducted for each tank per day from the contractor due. (ii) A separate register to be maintained by contractor for cleaning and occupant signature with date to be obtained in it.

Supply and fixing in repair of brass Spindle with cap / without cap suitable for 15mm dia CP tap/Cp Stop cock (short/long body/CP pillar taps as per sample to match the existing fittings as per site requirement complete all as specifried and directed.

Supply and fixing in repair sink coupling of any dia suitable as per site requirement complete all as specified and directed.

Dismantling of ceiling boards (fibre, pulp, insulation, etc.) or insulation boards /slabs/ blankets, any thickness, including cover fillets, as in false ceiling etc complete all as specified.

Supply and fixing of anodised GI snap grid frame work for false ceiling grid 605x605 mm fixed with Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including Supply and fixing Gypsum Board 12mm thick as in ceilings fixed with screws as per manufactures instructions etc complete all as specified and directed. NOTE : - Unit rate quoted against this item shall also include the taking down any electrical board, fittings etc affected for removing and refixing after repair work includes making good etc complete all as specified and directed.

Supply and fixing of semi perforated false ceiling 12 mm thick with micro tegular edged at all height with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and pattern having moisutre content less than 2%, humidity resistance of 99%, NRC 0.60 to 0.85 as per IS 8225-1987, non combustible as per BS 476 (Part-4) 1970 and light code description unit code No 429 Sub Head 26. New Technologies and materials reflectance of 85% minimum to be laid in true horizontal level suspended on interlocking metal T -grid of hot dipped galvanised iron section of 0.33 mm thick ( galvanised @ 120 gms/ sqm including both sides) comprising of main T- runners of size 15x 32mm of length 3000mm, cross T of size 15 x32 mm of length 1200mm and secondary intermediate cross T of size 15 x 32 mm of length 600 mm to from grid module of size 600 x 600 mm, suspended form ceiliing using galvanised mild steel items (Galvanised @ 80 gm/sqm) i.e. 50 mm long, 8mm outer diameter M-6 dash fastners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85 x 25 x 2mm. galvanised iron perimeter wall angle of size 24 x 24 x 0.4 mm of length 3000 mm to be fixed on perimeter wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall SS screws. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge complete all as specified and directed. NOTE : - Unit rate quoted against this item shall also includes taking down and refixing the same of any electrical board, switch, sockets, light and fittings, fans etc after carrying out necessary relevant work and making good to match with existing surface effected for this area etc complete all as specified and directed.

Material and labour for re-securing/ adjusting existing false ceiling grid, any type and make required tightening to remove sag portion/ depression in false ceiling grid including replacement of missing sections / part/ suspenders as per existing size etc complete all as specified.

Supply and fixing missing / damaged perforated ceiling boards in existing grid as per existing size and including painting required on front face including taking down damage/broken board etc complete all as specified and directed.

Supply and fixing missing / damaged metal ceiling boards in existing grid as per existing size including taking down damaged/Bkn boards etc complete all as specified and directed.

Supply and fixing in repair Steel tube of 50 mm bore, medium grade galvanized, fixed to walls as in additional support of ceiling , etc including cutting and chasing in wall and making good with PCC 1:3:6 to old existing surface complete all as specified and directed .

Material and labour for preparation of new plastered surfaces of walls and applying two coat of cement base paint over a coat of alkali primer complete all as specified and directed.

Supply and fixing Factory Made Single Extruded WPC (Wooden Polymer Composite) Solid Plain Board 6mm Thick comprising of virgin polymer of K Value 58 -60 (Suspension Grade), Calcium Carbonate and Natural Fibers (Wood Power / Rice Husk /Wheat Husk) and Non-Toxic Adhesives (Maximum Toxicity index of 6 for 100 gram) having minimum density of 650 Kg/ CUM and Screw withrawal strength 1800 N (face) and 900 N (Edge), Minimum Compressive strength 50 N/ mm 2. Modulus elasticity 850 N / mm Sq and Resistance to spread of flam of class A category with property of being termite/ borer proof, Water Proof/ Moisture Proof and Fire Retardant and fixing with stainless steel butt hinges of required size with necessary full body threated star headed counter sunk SS Screws,, solvent cement /adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed by Engr–in–Charge. (Note: Stainless Steel butt hinges and necessary SS screws shall be paid separately) Note: Material Test Certificate and Authentication should be provided by the manufacturing company.

NOTE:- Amount of credit of Rs. 59,214.00 for retrieved materials is mentioned in Schedule of Credit Page No 19 & 20 of tender documents in pdf form which will be deducted offline while acceptance of tender.

m/s parmod kamar (BID ID -3489494)

Ashwani Kumar (BID ID -3490713)

G8 CONSTRUCTIONS (BID ID -3490117)