Renovation of P & T Department office at 8th Floor Block-2, Sachivalay Gandhinagar

Name of Work :- Renovation of P & T Department office at 8th Floor Block-2, Sachivalay Gandhinagar.

BILL OF QUANTITIES

PART-A (Civil Work)

(A) Percentage Rate Tender (Up to INR 50 Cr. )

Item No Description of Item (with brief specification and reference to book of specifications) Quantity Unit Rate In figures Amount

Demolition Of Old Furniture, Panneling,Partition,Damaged False Ceiling (POP

ITEM NO.01 sheet),Alluminium Frame Of False Ceiling etc. & disposal of unservicable Materials removal 79.00 SQM 515.70

from site with all lead and lift as Directed by architect.

Dismantling doors, windows, ventilators etc. (wood or steel) shutters including chowkhats,

holdfasts and other attachment etc. complete and stacking them within all lead and lift.

ITEM NO.02 30.00 NOs 330.20

( i i ) Exceeding 3 sq.m. in area.

Providing and fixing 62.5mm to 75mm th. full height double skin partition. It should be

made from 50mmx38mm x1.50mm thick alluminium frame (C/C 600x600MM)covered

with both side 9mm thick marin ply finished with 1.0mm laminate and partly 12mm thick

soft board without any air gap and grooving as per design. Neccesary wooden framing to

be erected above false ceiling. Open edges to be finished with laminate.No extra cost to be

ITEM NO.03 157.00 SQM 5963.63

paid for the same. Before installation, make hole/face plate for conduit pipes of electrical /

networking cables with openable stud from partition Including all materials and labour,

with all lead and lift etc. complete as per detail drawing and instruction of engineer-in

charge. Only visible area to be measured for mode of payment. Entire work to be

completed as per the instructions of EIC / Architects.

Providing and Fixing 12 mm thick plaster of paris (gypsum anhydrous) ceiling tiles upto

height of 5 metres above floor level over wooden/alluminium frame work including

providing `v` groove at the joints , brass screws at @ 30 cm c/c and rendered smooth with

POP complete with Providing and Fixing anodised alluminium work consisting of tee/

angle sections, of approved make conforming to IS: 733 in frames of false ceiling including

ITEM NO.04 allumunium angle cleats with neccessury brass screws, alluminium perimeter angles fixed 197.00 SQM 1386.70

to wall with rawl plugs at about 450mm c/c and fixing the frame work to level adjusting

hangers ( 6mm dia. MS rods or any other approved material ) with neccessary cadmium

plated machine screws, all as per approved drawing and directions of EIC.(Approximate

weight of alluminium tees and angles shall be @1.20kg/sq.m of ceiling area) Including with

all lead and lift.

Providing and fixing fully glazed partition using 12mm thk Modi guard make clear

toughened float glass fixed with necessary patch fittings(Archie/Ozone make), D brackets

etc. As per the manufacturers specification or as directed by the EIC/Architect. Necessary

ITEM NO.05 wooden framing to be erected above false ceiling. Only visible area to be measured for 25.00 SQM 6800.00

mode of payment. Item including of all the taxes, VAT as per the prevalent rules, materials,

transportation,erection of complete item with all lead and lift. as directed by EIC/Architect.

Service Tax shall be paid separately as per prevailing rules.

Providing and fixing glass door with patch fitting as shown in the drg. Door shall consist of

approved make 12mm thk. toughened clear float glass with pre-fitted necessary hardwares

of Enox / Ozone make for smooth swinging action. Rate shall include necessary approved

ITEM NO.06 locking systems, S.S. brush finished `H' type Handle pair, floor springs (Heavy duty or 4.50 sqm 15808.50

equivalent), gaskets & miscellaneous hardware items. Including all materials and labour,

with all lead and lift. etc. complete as per detail drawing and instruction of engineer-in

charge and consultant.

Dismantling old plaster racking out joints and cleaning the surface to make ready for new

ITEM NO.07 150.00 SQM 45.90

plastering including disposal of rubbish to the dumping ground with all lead and lift.

Dismantling tiled or stone floors laid in mortar including stacking of seviceable materials

ITEM NO.08 200.00 SQM 59.00

and disposal of unserviceable materials with all lead and lift.

P & L different size/1200*600 mm of vitrified 8 mm thick tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on

ITEM NO.09 existing flooring by adhesive material including dismentaling of existing flooring and 200.00 SQM 1181.00

jointed with color cement slurry including finised with flush pointing & cleaning the

surface, with all lead and lift. etc. complete

Brick work using common burnt clay building bricks having crushing strength not less than

35 kg/sq.cm. in foundation and plinth in C.M.1:5 (1cement :5 fine sand) conventional bricks

with Extra for brick work in superstructure above floor two level (To be added for every

ITEM NO.10 8.00 CUM 5223.00

additional floor)

( I ) With C.M. (1:5)

Providing 15 mm thick cement plaster in single coat on wall for interior plastering upto

floor two level finished even and smooth in cement mortar 1:3 (1 cement : 3 fine sand)

ITEM NO.11 300.00 SQM 422.00

with extra for interior plastering above floor two level, to be added for every additional

Providing and applying plaster of paris putty of average 2mm thickness over plastered

ITEM NO.12 300.00 SQM 211.30

surface to prepare the surfacec even and smooth.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture

ITEM NO.13 on WALL surface to give an even shade including thoroughly brushing the surface free 200.00 SQM 104.30

from mortar droping and other foreign matter and sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture

ITEM NO.14 on CEILING/SLOPING ROOF surface to give an even shade including thoroughly brushing 150.00 SQM 111.20

the surface free from mortar droping and other foreign matter and sand papered smooth.

Providing Roller blackout blinds with 3 pass eco blackout fabric 100% polyster fabric (plain

veneer) with plgment PVA - coating on both side of fabric wid. Dupont black coatery.

Sandwich with roller 38 m mechanism with endless chain and with installation as per

ITEM NO.15 35.00 SQM 1795.00

approved Specifications, design and drawings, including of all the taxes, VAT as per the

prevalent rules, materials, transportation, erection of complete item as directed by

EIC/Architect.Service Tax shall be paid separately as per prevailing rules.

Sofa: Supplying & Fixing 3 Str with -3 seater-1720(w)* 800 (d)*750(h). leather :synthetic

Frame material : tropical solid wood, Seat foam : polyurethane foam with recron layer.

ITEM NO.16 9.00 NOS 63256.20

Foam density : 18 kg/ cubic cm. Back foam : polyurethane foam with silicon fill At arms.

Foam density : 22 kg/cubic cm, with all lead and lift.

Providing & fixing granite on soffits of all window openings laid over 20mm thick base

cement mortar 1:4(1 cement: 4 coarse sand) fixed with cement slurry, after preparing

sanded surface on the backside of granite strip (sand is sticked to the granite with Araldite)

minimum width of granite strip is 300 mm and maximum 400mm as per site wall. Wall

ITEM NO.17 23.00 SQM 3423.00

joints are finished with 5mm wide & 2mm deep groove finished with neat cement slurry.

All edges of granite are chamfered & polished as per detailed drawing, complete as per

specification & drawings provided by architect. All materials with all lead and lift., brands

shall be approved by architect

Providing and Fixing anodised alluminium section Three track windows with outer frame

91.5 mm x 31.5 mm of 19G, weighing 0.92 kg/m and shutter frame 34.5 mm x 15.80 mm

ITEM NO.18 of 19G, weighing 0.38 kg/m with all arrangement for fixing, PVC weather strip, spring 34.00 SQM 2900.00

handles and other fixtures etc including fixing 4mm glass of approved quality as directed

with all lead and lift etc complete.

Providing and Fixing 35 mm thick panelled, glazed or panneled and glazed shutters for

doors, windows, and clearestory windows including brass butt hinges, screws, fixtures and

ITEM NO.19 Indian teak wood shutters with 27.00 SQM 4125.00

( A ) Marine ply wood sheet panels 12mm ( IS : 710 ) with all lead and lifts

DS cabin Office Table: Supplying & Fixing Executive table with The Main table shall be of

size 1800 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall

made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating

of Laminate. The Main desk should contain in built key board pull out tray for keeping

keyboard of computer. The front modesty panel of the table shall be made up of MDF

board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener

and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided

ITEM NO.20 of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also 2.00 NOS 119250.60

be made up of MDF duly finished with veener & final coating of PU. The Side shall be of

size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of

MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side

unit shall be such that it can be placed on either side of the main table. The side unit shall

contain open space for keeping cpu in extreme right side, one closed storage shutter at

extreme left end & open space in the middle with one shelf for keeping files. The thickness

of the top of the side unit shall be 25mm. with all lead and lift.

Providing wooden computer table of size 48'' x 24'' x 30'' and height 30''.Table top in

required shape to be made from 18mm pre lamineted board structure , including

providing drawers CPU box and keyboard drawers as per given design, Including painting

two coats on inside surface with Providing storage unit of specified size as per

ITEM NO.21 design/drawing and 75cm height, storage cabinet to be made from 19mm thick block 25.00 NOS 8143.20

board with Laminates on exposed side. Back and shelves to be made from 12 mm marine

ply as per instruction of EIC. Shutter to be made from 19mm thick marine ply with and

laminated teak wood beading,including locking arrangement, SS handle, hinges, screws of

approved quality with all lead and lift. etc. complete.

Supplying and Placing Office Table 1500mm W x 900mm D x 740mm H Worktop Made

from 25mm Thick Pre-laminated Particle board. All the edges are sealed with 2mm thick

PVC edge band all around, Side Panels Made from 25mm Thick Pre-laminated Particle

board. All the edges are sealed with 2mm thick PVC Edge band on the user side and

mm on the Top and Bottom Side. The side panels have 2 glide screws each for leveling of

the desk. Modesty Panel made from 18 mm Thick Pre-laminated Particle board. All the

ITEM NO.22 edges are sealed with 0.8 mm thick PVC edge band all around Freestanding Pedestal The 5.00 NOS 133000.00

freestanding pedestal is made from 18mm Pre- laminated Particle board with a

combination of 2mm and 0.8mm PVC Edge band on all the exposed surfaces as per

requirement. The drawers are provided with suitable slides for smooth operation. All the

pedestal drawers are centrally locked with a single key. The entire desk unit is assembled

with suitable KD fittings and hardware. Each side panel is provided with a cutout for laying

cables for the monitor and other computer accessories with all lead and lift.

Full Height Storage:

Providing, making, polishing and fixing full-height storage of size 450 mm depth as per

reference drawing.

Material of Construction:

1) Top: 19 mm thick BWR ply finished with 1 mm thick laminate sheet of approved shade,

finish and make. Ply shall confirm to IS

2) Storage Base: The table legs shall be made by 19 mm thick BWR ply confirming to IS

to be finished with 1 mm thick laminate of approved make, shade and texture as per

reference drawing.

ITEM NO.23 3) Sides: The sides shall be made by 19 mm thick BWR ply confirming to IS 303 to be 56.00 SQM 13684.43

finished with 1 mm thick laminate of approved make, shade and texture as per reference

4) Partitions: Horizontal and vertical partition shall be made of 19 mm thick BWR ply and

shall be finished with 0.8 mm thick laminate of approved make, shade and finish.

5) Lipping: 6 mm thick lipping of ghana teak wood shall be applied on all exposed edges of

veneer and ply as per reference drawing.

6) Polish: Monocoat polish shall be done on all exposed faces of wood and veneer.

8) 0.8 mm thick balancing laminate of approved make, shade and finish to be applied on

all inner faces of top, bottom, sides, shutters, drawers, shelves and partitions as per the

instruction of Architect.

Providing teak wood center Teapoi 900 x 600 x 380mm. with 12mm glass top and lacquer

ITEM NO.24 9) Hardware: Hinges: L Hinges of size 75 mm x 18 mm shall be used in requisite quantity 6.00 Nos 3190.00

as approved by the engineer-in-charge; Magnet Lock: 2 Nos. per active shutter; Shutter Total

stop chain: 1 no. per shutter; Handles: G - profile handles of approved.

The work shall be done as per the approved shop drawing (to be prepared by contractor),

specifications, sample approved and as directed by the Architect and Engineer-in-charge.

Name of Work :- Renovation of P & T Department office at 8th Floor Block-2, Sachivalay Gandhinagar.

PART-B (Electric work.)

ITEM DESCRIPTION UNIT. RATE. AMOUNT.

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured/metallic/white front

plate modules erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories erected flushed on

wall/ceiling complete Cat. III

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of

1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires, in below type of pipe to be erected

complete with earth continuity and necessary connection with primary

light with accessories erected on Metal / PVC / wooden box covered

with 3 mm thick PC(Polycarbonate) / Acrylic sheet for open / concealed

2 20 wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as Pt. 119

Note:- Maximum up to 6 mtrs length, excess will be considered as Mains

for Secondary Point.

(j) in existing pipe erected erected concealed in wall/ceiling complete

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green)

both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type electronic fan

regulator mounted and accessories with earth continuity of following

3 18 type erected on PVC / Metallic/Wooden box, single mounting base frame Pt. 632

covered with textured/metallic/white front plate modules erected on / in

wall / ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories erected flushed on

wall/ceiling complete Cat. III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules

4 40 erected on / in wall / ceiling as per pipe erected with following type of Pt. 471

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby

switchboard/mcb db board

(a) with medium class Rigid PVC pipe and accessories erected flushed on

wall/ceiling complete Cat. III

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb

40 db board.(a) with medium class Rigid PVC pipe and accessories erected Pt. 704

flushed on wall/ceiling complete Cat. III

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire with

sq.mm ( green) earthing wire from mcb d b board.(a) with medium class

Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Point wiring for on board Looped Plug with 6A Modular type switch &

pin socket erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate modules

erected on / in wall / ceiling with following type accessories Cat. III

Providing following type of Modular Type Accessories mounted with PVC

/ metallic/Wooden box, single mounting base frame covered with

6 5 textured / metallic/white front plate , modules erected with necessary Nos 159

connections as per site situation directed by Engineer In charge.

(4) TV Co-axial Socket outlet Cat III

18 (5) Electronic hum Free steps EME Fan regulator Cat.III Nos 395

48 (8) Computer RJ-45 socket Cat.III Nos 159

36 (14)6A/10A/16A/20A/25A/32ADoublePoleModular MCB Switch Cat.III Nos 406

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

7 1800 necessary PVC fittings & Junction boxes fixed with adhesive solution & Mtr. 33

Clamps with following dia of pipes, in approved manner as directed

Providing & erecting PVC Corrugated Flexible Conduit with required nos.

8 100 of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (2) Mtr. 21

Supplying and laying UPVC cable trunking system comprising

unplasticised polyvinyl, chloride rigid material with ignition free and

9 50 flame proof confirming BS with necessary end caps Internal and external Mtr. 275

bend, flat bends, coupler, tee etc..All necessary accessories and

measuring of following sizes (1) 75 mm x 50 mm trunking

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

10 2500 conductor FRLS PVC insulated stranded wire of green colour for earth Mtr. 82

continuity of following size

(A) With medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following

size (A) with medium class Rigid PVC pipe and accessories a) 2 wire 4 sq.

(a) with medium class Rigid PVC pipe and accessories

(b) 2 wire 6 sq. mm

Supplying and erecting Flexible PVC insulated multistrand multicore

12 300 kv grade ISI marked copper wires of following size to be erected as Mtr. 46

directed. e) 1.50 Sq.mm 3 core round PVC sheathed

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan

with double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz

13 18 1200 mm sweep complete having 3blades with aluminium blades with , Nos 1929

canopy & 30 cm. down rod erected with earthing.(Make shall be

approved by Engineer in charge)

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to

the RCC bars up to 50mm length each side and pierced through a

Gauge M.S. box / Heavy Duty PVC box complete erected concealed in

Ceiling with necessary finishing.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S.

16 18 Pipe down rod erected duly painted for fan complete with proper Mtr. 107

insulation without leakage and earthing.

Providing & Erecting approved make following size of TV Co-axial flexible

cable comprising inner conductor of solid bare copper insulated with

17 60 Foam PE & Secondary conductor made of poly - Aluminium film bonded Mtr. 39

Al. Braids @ suitable coverage overall sheathed with black PVC

insulation. b)RG-6

Providing & erecting Switch board for Computer or electric apparatus

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered

with textured/metallic /white front plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

Supplying & erecting Electronic Type Cordless Call Bell erected on

19 10 PVC/Metal board having portable bell push working on D.C. & bell on Nos 248

230V A.C. supply with cells / battery

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III

Providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Providing & erecting 240 V MCB double pole switch for lighting Load (B

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing

box having following capacity

(A) 6 to 32 Amp. Cat III

Providing & erecting 240 V MCB double pole switch for lighting Load (B

23 20 Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing Nos 293

box having following capacity (B) 40 Amp. Cat.III

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth bar

and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to

house appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase outgoing

(b) sheet steel double door (IP-43) (iv)(iii)8 way

(B) three phase incoming and single phase horizontal type outgoing Per

phase isolation type (PPI) (b) sheet steel double door (iii)8 way

Providing and erecting Approved make RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected

as directed (ii) 40Amps. DP Cat III

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B

26 12 curve) having 10KA breaking capacity & confirms to IS :8828 in existing Nos 632

box having following capacity (b)40 Amp. Cat III

Supplying & erecting approved make RCCB + MCB (Electro magnetic type

only) working on residual current device having 6 KA short circuit

breaking capacity and 30 mAmp. Sensitivity & 30 mili sec. tripping time

27 6 conforming to IS 12640 test knob facility trip free mechanism operating Nos 2145

for rated leakage at nominal ten volt, complete erected including all

materials lugs screws etc. completed.

[e] 32A to 40 A, 4 Pole Three Phase Cat. II

28 12 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. kg 787

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall with

29 60 necessary clamps or in existing trench / pipe at road crossing or floor Mtr. 392

of following size of cable.

(C) 3 core 6 Sq. mm

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable

30 60 1.1 KV grade to be erected as directed of following size. Mtr. 361

(L) 4 core 6 Sq. mm

60 (M) 4 core 10 Sq. mm Mtr. 568

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt

to 0.5 Watt assembled on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in aluminium casted body

with company mark/name

160V to 270V,Power Factor more than 0.9, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with

48 provision for spring loaded mounting clips complete.IP20 Ea. 584

(iii) 16-20 watts, Surge-2 KV Cat-III

(B) LED Panel Light with provision for Plane front frame with translucent

22 cover fixed to housing complete.IP20 Ea. 1777

(vi) 36 watts, 24" x 24", Surge- 2KV

Supplying and erecting approved make oscillating type bracket fan A.C.

23OV. 50cy/s 400/450 mm sweep wall mounted with height adjustment

and rotary tilting device complete with guard, flexible Core plug top

complete erected with lead wires as directed. Cat.II

PART-A (Civil Work)

PART-B(Electric work.)

I/We am/are willing to carry out the work at… …..% above/below percent(Should be written in figures and words) of the estimated rate

mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

Quantity Item Description Rate Per Amount

7.00 High back chair (7 Nos),, , Recovery Window 1566 Nos

38.00 Medium back (38 Nos) 1218.00 Nos

Doble door cupboard (3 Nos) + Three door cupboard (25Nos) + storage

unites (14 Nos)

12.00 Single sofa (3Nos) +2 seater sofa (3Nos) + 3 seater sofa (1 Nos), 1914.00 RM

14.00 Table (7 NOS) 3381.00 SQM

13.23 Recovery Window 652.71 SQM

An fix amount of Rs.3,91,407.00 shall be considered as recovery of material obtained from the dismantling of existing structure and

shall be recovered/ deducted from 1st R.A bill or shall be deposited in the GMB NON PLD account by the agency as detailed below.

ACCOUNT NAME GMB NON PLD

BANK State Bank of India, Gandhinagar

Branch GMB Complex, Gandhinagar