E-Tender No.32/EDC(S)/2024-25

Amount

Material

Holding Clamp for SP-33/55 with N&B.

11 KV ACS AL-59 Equivalent 52.88 sqmm Covered Conductor (SS4240813 & SS4240814) EN 50397-1:2006 by Electron beam radiation process

MVCC Accessories as per EN 50397-2.

Tension Clamp & Ball

11 KV Suspension ties on every Pin Insulator.

11 Kv IPC for CC to CC Connection in every section Pole.

11 Kv IPC for CC to Bare Connection at both end and Tapping.

11 KV Mid Span Jointing Kit at every 500mt. Cable drum.

Supply IPC with Aluminium bail for earthing

Labour

Cartage of SP-55/33 Poles from store centre to nearest road site with loading, unloading at both points. (Loading, unloading plus carriage per pole) (0 to 50 km).

ST Pole SP-55

ST Pole SP 33

Cartage of other material by vehicle from store centre to nearest road site including loading and unloading at both ends. (0 to 20 km).

Head load of SP-55/33 Poles from store centre to nearest road site with loading, unloading at both points. (Loading, unloading plus carriage per pole) (0 to 1 km).

ST Pole SP-55

ST Pole sp-33 (Bottom Portion Hot dip)

Head load cartage of small material by vehicle from store centre to nearest road site including loading and unloading at both ends. (0 to 1 km).

Excavation of earth for pole pit of size 0.9X0.9X1/6 of full length of pole for erection of pole in all type of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work.

Grouting of pole in size 0.45X0.45X1/9 of the support in CC ratio 1:4:8 (1 cement:4graded stone 20mm nominal size:8coarse sand) block including cost of cement, sand and stone ballast back filling of soil and boulders back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO construction manual.

Erection of following Single support pole in proper level and alignment alongwith fixing of all accessories (STP SP-33).

Erection of following Single support pole in proper level and alignment alongwith fixing of all accessories (STP SP-55).

Proper Alignment of Tilted Poles

T/f Jumpering and connection of Covered Conductor

Jumpering and connection of Section Pole

painting of Poles with angle and channel and all steel part by one coat red oxide primer and two coats of aluminium paint and two strip of flourescent alternate red and white paint 30 Cm wide and 1.5 Mtrs from ground level

Fabrication of MS Chanel and angle

Removing of old conductor with opening of binding,jumpering,and making of bundle with carriage from pit site to JE store including loading/unloading Complete work.

Rabbit Conductor

Laying,Spreading, Stringing and sagging of 11 KV Line in 3-phase of the following wire as phase wire including proper sagging l with binding and jumpering as per user manual and sagging chart. As per EN 50397 Part3.

11 KV ACS AL-59 Covered Conductor (120sqmm)

Fixing of MVCC Accessories

33KV 90 KN Tension clamp with Bail and IPC.

33KV Suspension ties.

33Kv IPC for CC to CC Connection.

33Kv IPC for CC to Bare Connection.

33KV Mid Span Jointing Kit.

Fixing of IPC with Aluminium bail for earthing .

Head load cartage of small material by vehicle from store centre to nearest road site including loading and unloading at both ends. (0 to 1 km).

safe cartage of weasel/rabbit conductor scrap from road side to store Srinagar

Sagar Engineering Company

M/s S S ENTERPRISES