Repair and Renovation of Kitchen inside the campus of District Institute of Education and Traning (DIET), South 24 Parganas.

Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.

Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m a) In ground floor including roof.

Dismantling R.C floor, roof beams etc. Including cutting rods and removing rubbish as directed within a lead of 75 m including stacking of steel bars. a) In ground floor including roof.

Dismatling artificial stone flooring upto 50 mm thick by care fully chiselling without damaging the base and removing as directed within a lead of 75 m.

Taking out carefully Ranigunge pattern tiles from roof stacking seviceable tiles at site and removing rubbish as directed within a lead of 75m

Stripping off worn.out plaster and raking out joints of walls, ceiling etc. Upto any height and in floor including removing rubbish within a lead of 75 mm as directed

Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge

Reparing collapsible gate by cutting out all rivets as necessary reassambling all members including welding pieces of channels, sraightening bent bars and rivetting with new rivets and fitting in position and painting two coats.

Easing and oiling, cleaning collapsible gate and repairing to locking arrangements

Taking out M.S. or W.I. Grills from wooden frame including cutting lugs from masonry wall and refitting the same and mending good damages after repairs. (Excluding the cost of necessary repair of damages) or doing any other necessary works.

Taking out door and window shutters and rehanging the same with old fittings. (b) With old screws.

Brick work with I st class bricks in cement morter (1:6) (b) In super structure, ground floor

125 mm thick brick work with ist class bricks in cement morter(1:4) ground floor

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. a) Pakur / Chandil Variety

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes.

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge-black annealed wire at every intersection, complete as per drawing and direction. Other than SAIL/TATA/RINL

Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within manufacturer's specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface).

(a) Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department]

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or rougening of concrete surface, including throating, nosing and drip course where necessary (ground floor) (i) With 1:6 cement mortar (b) 20 mm. thick plaster

15 mm thick

ii) with 1:4 cement morter 10 mm thick

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m.

Supplying , fitting and fixing Black Stone slab used in Kitchen slab, alcove, wordrobe etc. laid and jointed with necessary adhesive Cement Morter (1:2) including grinding or polishing as per direction of Engineer in Charge in ground floor Slab thickness above 25 mm and upto 37.50 mm making rake & table

Supplying, fitting and fixing 1st quality ceramic tiles in walls & floors to match with the existing work, s & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the, colour of tile including roughning of concrete surface, if necessary or by synthetic adhesive & grout matirials etc. (B) Wall with sand cement morter (1:3) 15 mm thick & 2mm thick cement slurry at back side of tiles using cement @ 2.91 kg/Sq.m. & joint filling using white cement slury @ 0.20 kg/Sq.m. (b)Area of each tile above 0.09 Sq.m. (i)Other than Coloured decorative including white.

Supplying and laying true to line and level vitrified tiles of approved brand (Size not less than 600 mm x 600 mm x 10 mm thick)in floor,skirting etc. set in 20 mm sand cement morter (1:4) and 2 mm thick cement slarry back side of tiles using cement @ 2.91 Kg/Sq.m or using polymerised adhesive (6mm thick layer applied directly over finished artificial stone floor/ Mosaic etc.Without any backing course) laid after application slury using 1.75 kg of cement per Sq.m below morter only , joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles using soft and dry cloth upto mirror finish complete including the cost of materials , labour and all other including charges complete true to the manufacture's specification and direction of Engineer-in-charge (White cement ,synthetic adhessive and grout material to be applied by contactor. II) With application slurry @ 1.75kg/Sq.M 20 mm sand cement morter (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/Sq.m white cement for jouinting filling with pigment B) light colour

18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in - charge to match with the existing work. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @2.0 kg/Sq.m]

Extra cost of labour for grinding Kota Stone Floor in treads and riser of Steps.

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (ii) Grill weighing above 16 kg

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (f) Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak.

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm. (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

Supplying , Fitting and fixing M.S clamps for door and Window frame made of flat bent bar and bifercated with necessary screws etc. by cement concrete (1:2:4) as per direction a) 40 mm x 6 mm , 250 mm length

Iron butt hinge of approved quality fitted and fixed with steel screw, with isi mark vii) 100 mm x 58 mm x 1.90 mm

Anodised aluminium barrel/ tower / socket bolt (full coverd) of approved manufactureed from extruded section conforming to I.s 204/74 fitted and fixed with cadium plated screw x) 300 mm long x 12 mm dia bolt

Anodised aluminium Aldrop/sliding bolts of approved manufactureed from extruded section conforming to I.s specification (2681/66) fitted and fixed complete (i)250 mm x 16 mm dia bolt

Anodised aluminium D type handle of approved manufactureed from extruded section conforming to I.s specification (230/72 fitted and fixed with cadium plated screw With continous plate base 150 mm grip x 12 mm dia rod

Supplying fitting & fixing of 2 track / 3 track Aluminium sliding Window of all aluminium section viz. window frame (to, bottom & side frame) shutter (top, bottom, side & interlock member ) made of aluminium alloy extrussion conforming to is 733-1983 & 1285-1975, anodised conforming to IS 1868-1983 fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screw etc.including labour chargees for fitting and fixing of aluminium 2track/ 3track sliding window with fixing of glass (excluding cost of glass)all complete as per architectural drawing and direction of Engineer in charge. 1o-12 Micron thickness Anodizing film Natural white

Supplying buble free float glass of approved make and brand conformining to i.s 2835-1987 iv) 5 mm thick colour /tinted/smoke glass

Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge)

Scraping and removing greasy soot from walls or ceiling of kitchenor similer smoke affected rooms and preparing the surface.

Removing old scales, blisters etc. of interior surface of walls,ceiling byscraping etc. and preparing smooth and even surface with rendering orcement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only whenthis has been done on the specific direction of the Engineer-in-charge).

(b) Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick)

Applying interior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive distemper/Acrylic emulsion paint including scraping and preparing the surface throughly, complete as permanufacturer's specification and as[per direction of the Engg-in-charge. (In Ground floor) (a) One coat i) Water based interior grade Acrylic Primer

Applying Acrylic Emuision paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) (Two coats) i)Standard Quality

Applying extrrior grade Acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to received decorative texture (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and prepairing the surface throughly complete as per manufactures specification and as per direction of the EIC. (a)One coat Ground Floor

Protective and decorative Acrylic exterior emulsion paint of approved quality, as per manufavture's specification and as per direction of E.I.C to be applied over acrylic primer as requried. The rate includes cost of materials. Labour, scaffolding and all incidental charges but excluding the cost of primer a) Normal Acrylic Emulsion (Two coats) Ground Floor

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (a) On timber or plastered surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white)

(b) On steel or other metal surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white)

Supplying, fitting and fixing CPVC(Chlorinated Polyvinyl Chloride) pipes of approved make conforming to I S - 15778 : 2007 with all necesssary accessories, specials viz socket, reducing socket, bend tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short pice etc. fitted with holder bats clamps, including cutting pipes, making thredes, fitting, fixing etc.complete in all respect including cost of all necessary fittings as requred, joininting materials in any position above ground . (A) For Exposed Work (a) (ii) 15 mm

(b) 20 mm dia

( c ) 25 mm dia

D)32 mm dia

Supplying and fitting and fixing gunmetal wheel valve of approoved brand and maketested to 21 kg per Sq.cm.(for water line only)) vii) 20 mm dia

vii) 25 mm dia

Supplying, fitting and fixing bib cock or stop cock. (a) (ii) Chromium plated Bib cock long body with wall flange with aerator

(e) PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent) 15 mm

d) (i) Chromium plated angular stop Cock with wall flange

Supplying, fitting and fixing Wash basin vitreous china best quality approved make wash basin with C.I brackets on 75 mm X 75 mm wooden blocks CP waste fittings of 32 mm dia, one approved quality brass C.P piller cock of 15 mm dia , C.P chain with rubber plug of 30 mm dia , approved quality P.V.C waste pipe withC.P nuts 32 mm dia, 900 mm long approved quality P.V.C connection pipe with heavy brass C.P nut including mending good damages and painting the brackets with two coats of approved paintsand C.i brackets including two coats of painting of C.I brackets. ii) 550mm x 400 mm

Supplying , fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass c.P nut 15 mm dia. iv) 750 mm long

Supplying, fitting and fixing towal rail with two brackets. (b) Aluminium (i) 25 mm dia 450 mm long

Supplying ,fitting and fixing soap holder, a) PTMT(prayag or Equvalant)

Supply of UPVC pipes (B-Type) & fittings conforming to I.S- 13592 -1992 (ii) Double socketed 3 metre length (b)110 mm

B) Fittings (ii) Plain tee (b) 110 mm

Supplying , fitting and fixing Waste fittings complete. a) C.P over brass iii) 40 mm

Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe,with PVC coupling at one end fitted with necessary clamps .(iv) 1050 mm long

Supplying fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of c.i brackets a) Sink only ii) 530mm x 430 mm x 180 mm

Add 18 % G.S.T

Add 1% labour Cess