Restoration of rain damages to WSS Trashi, Shanod Ranharu in G.P. Katrain in Tehsil Distt. Kullu HP.

Excavation in foundations, trenches etc.in all kind of soil in all leads and lifts such as pick work, jumper work in saturated/unsaturated soil including bailing out water, blasting work in hard/ soft rock or chiseling in hard/soft rock where blasting is prohibited in all lifts stacking the excavated earth not more than 3 mtrs clear from the edge of excavation and then returning the stacked soil in 15 cm layers when required into plinths sides of each deposited layer by ramming and watering and then disposing of all surplus excavated earth foundations etc., consolidating as directed within all leads and lifts and handing over the useable materials available from excavation to department free of cost to the entire staisfaction of Engineer-in-charge with in all leads and lifts.

Providing and laying cement concrete 1:3:6 (1cement :3 sand :6 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work in in foundation and plinth.

Providing & laying reinforcement cement concrete 1:1.5:3(1cement:1½ sand:3graded stone agregate of 20mm nominal size) curing complete excluding cost of from work and reinforcemenr for reinforced concrete work including all leads and lifts.

Foundations , footings bases of columns and the like and mass concrete work complete in all respect.

Walls any thikness but not less that 0.10 Mtrs thickness including attached pilasters, buttresses plinth and string courses etc, from top of foundation (level) upto floor two level including all leads and lifts etc. complete in all respect.

Suspended floors, roofs, landing, shelves and their supports balconies, beams and girders bressumers and cantilevers upto floor two levels including all leads and lifts etc. complete in all respect.

Providing and placing tor steel reinforcement for RCC work including bending, binding and placing in position complete up to floor two level including cost of binding wires and carriage of materials upto all leads & lifts as per the direction & entire satisfaction of Engineer-in-charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5 mm so as to give a rough finish including centering shuttering and propping etc. Height of propping and cetering below supporting floor to seiling not exceeding 4 mtrs and removel of th same for the same for in situ reinforcement concrete and plain concrete concrete work including all leads and lifts.

Flat surface such as soffits of suspended floors, roofs, landing and the like floors etc. Upto 200mm in thickness including all leads and lifts etc. complete in all leads and lifts.

Vertical surface such as walls (any thikness) portions and the like including attached pilaster buttersses plinth and stiring course and the like

Fixing, jointing and testing of GMS tubes light grades of following dia meter for inlet, outlet & scouring etc. complete fitting with tees and other accessories as per JSV specification within all leads and lifts and entire satisfaction of Engineer in charge.

80mm dia

65mm dia

Providing and fixing MS man hole cover of size 600 x 600 mm made up of 3.15 mm thick plain MS sheet fixed in angle iron frame frame of 50x50x5mm supported with MS flat of 50x5mm at center of sheet including fising hold fast ,hinges and locking arrangement and lock of medium size etc complete in all respects.

Providing,supplying & fixing of ISI Marked copper Alloy Secrewed end Gate Valves (Class-II) for water works purpose as per ISI 778: 1984 ( Reaffirmed-2010) with latest ammendments in all respect as per direction and satisfation of Enginner in charge.

80mm dia

Laying, jointing and testing in trenches of galvanised mild steel of following dia meter, including carriage of pipe and cost of fittings such as tee, elbow, union and nipple etc. of ISI marked and testing for leakage complete with in all leads and as per the direction of Engineer in charge (Earth work in trenches to be measured and paid for seperately)

20mm dia

25mm dia