Spl repair to Bldg No T-21 at basic gp of 48(I) sup PL ASC Ramgarh cantt

Amount

Demolition of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including removal of rubbish out off from site etc complete all as specified and directed.

M&L for Brick work using sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

M&L for rendering 10 mm thick on fair face brick masonry/concrete surface etc., in cement mortar 1:6, surface finished even & smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plaster surface of wall and applying two coats of cement base paint over a coat of alkali primer including necessary scaffolding complete all as specified & as directed.

Taking down strong air roof turbo ventilator exhaust fan of any sweep after disconnecting all necessary connections for repair and refixing in the same opening and same place & position complete all as specified & directed by Engineer-in-charge.

Dismantling old asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridge complete all as specified & directed.

S & F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F 2mm thick Fibre glass reinforced translucent corrugated sheeting in roof, walls etc with two corrugation side lap fixed with L-type or J-type or cranked hook bolts etc complete all as specified.

M&L for prepatation of old plastered surface of wall and applying two coats of distemper oil emulsion (OBD) complete all as specified and directed.

M&L for prepatation of old plastered surface wall and applying two coats of cement based paint complete all as specified and directed.

Taking down chowkats or frames with shutters exceeding 1.5 Sqm sqm but not exceeding 4.00 sqm each (without taking off shutters from the frames) etc including builders hardware etc and removing from site and making good disturbed surface of walls in cement mortar (1:3) complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.50 sqm each and removing from site and making good disturbed surface of walls in cement mortar (1:3) complete all as specified & directed.

Forming jambs, etc, in CM 1:4 to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and directed

S & F for Factory made steel window box type using ERW hollow Z section comprising double frame for and including gauged and glazed skeleton shutter jointed internally with flat iron 40 mm x4 mm complete including grill of 8mm square bars(solid) , fixed horizontally spacing @ 10cm c/c , including hinges, handle, tower bolt, stops, lungs etc complete all as specified and directed.

S & F for Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M & L for 3mm thick plain sheet glass ordinary quality and glazing with oil putty not exceeding 0.50 Sqm in each pane,complete all as specified and as directed by Engineer-in-Charge .

S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering, Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel handing door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified and directed.

S&F Steel door including hinges, steel handle, looking arrangement etc complete with glazing bars, dovetailed or selded, complete all as specified and directed.

M&L for preparing new steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surface complete all as specified and directed.

M&L for preparing old painted steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint on steel surface complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18mm -20 mm thick (of size not less than 575 mm X 575 mm), laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab with & including 20 mm thick screed bed in CM (1:4) including rubbing and beeswax polishing into mirror finish with roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust,etc.complete all as specifed & directed.

M&L for machine cut kota stone slab flooring 16mm -18 mm thick as in vertical surfaces such as skirting/dados in narrow width, laid over and including 10 mm thick rendering in cement mortar 1:3 on faces of brick work and jointed with grey cement slurry incl. including grinding, rubbing & with beewax polishing into mirror finish all as specified & directed.

M&L for demolition of cement concrete (un reinforced)in ground floor & paving of any thickness (above or below ground level )by mechanical tools and removing excavated material exceeding 1.50 km and not exceeding 5.0 km complete all as specified and directed

M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 (using 20mm graded crushed stone aggregate ) as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 grade and sand in the ratio 1:3 including necessary form work , complete all as specified and directed

simplex infra project

M/S KAMLESHWAR SINGH