SPECIAL REPAIR TO OFFRS MD ACCN BUILDING NO DOE-39, BUILDING NO. P-36 AT MH AND PROVISION OF CERTAIN MINOR WORKS UNDER AGE B/R II AT MILITARY STATION KOTA

Amount

Demolition/Dismantling of existing normal roof treatment comprising of PCC padding with or without wire mesh from RCC roof slab, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (Using 12.5 mm graded stone agg) for filling in pressed steel frames, roof padding, leveling course to receive floor finishes etc complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work of walls/surfaces of RCC roof slab in CM 1:4 duly mixed with liquid water proofing compound, finishing surfaces even and smooth without using extra cement, complete all as specified and directed. (WPC shall be measured and paid separately).

Supply only liquid water proofing compound as approved by the GE, complete all as specified and directed.

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish, reinforced with non-woven polyester mat with a thermo fusable finish, laid over compatible bitumen primer @ 0.40 Kg/Sqm, torching overlaps with propane or butane gas torch, with an overlap of 75mm at the sides and 100mm at the ends and sealing, complete all as per manufacturer’s instructions, specified and directed.

Item 6.00 Contd……. (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane shall be inserted in groove and sealed with paving bitumen. (v) Cost of these factors shall be deemed included in the unit rates.

Raking out joints (in old work) to random rubble or polygonal rubble uncoursed or brought upto course masonary, built in CM, complete all as specified and directed.

M&L for 15 mm thick rendering on other than fair faces of brick work or stone masonry surfaces in two layers, consisiting of 10 mm thick in CM 1:6 and over it 5 mm thick in CM 1:4, finishing surfaces fair and even without using extra cement complete all as specified and directed. Note: WPC shall be mixed with the cement mortar for the second layer. However WPC shall be measured and paid separately.

M&L for applying two coats of cement based paint over a coat of primer on newly plastered surfaces of walls including preparation of surfaces, complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and and in any position not otherwise specifically provided for and removing rubbish from premises, complete all as specified and directed.

M&L for preparing new previously untreated plastered surfaces of walls and applying 1 to 1.50 mm thick layer of wall care putty and over it applying two coats of weather proof modified exterior acrylic emulsion paint over a coat of primer, complete all as specified and directed.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL), complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 75 mm thick as in sub base, finishing the surface even & rough to receive topping layer, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

M&L for dark coloured (double charged) vitrified tiles, 10mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for dark coloured (double charged) vitrified tiles, 10mm thick (square/rectangular) area of each tile exceeding 0.42 Sqm but not exceeding 1.00 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L polished baroda green slabs, 18-20 mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of marble stone including grinding and polishing complete, laid over and including 20 mm thick screed in CM 1:6, complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 25 mm bore pipes complete all as specified and directed.

S&F 15 mm bore GI tubing, medium grade, with all GI fittings and fixed complete to walls, ceilings and floors, complete all as specified and directed.

S&F 20 mm bore GI tubing, medium grade, with all GI fittings and fixed complete to walls, ceilings and floors, complete all as specified and directed.

S&F 25 mm bore GI tubing, medium grade, with all GI fittings and fixed complete to walls, ceilings and floors, complete all as specified and directed.

Refixing old GI tubing with and including new GI fittings, 15 mm dia, in new or old position on walls, ceiling or floor, complete all as specified and directed.

Refixing old GI tubing with and including new GI fittings, 20 mm dia, in new or old position on walls, ceiling or floor, complete all as specified and directed.

Refixing old GI tubing with and including new GI fittings, 25 mm dia, in new or old position on walls, ceiling or floor, complete all as specified and directed.

Dismantling water storage tank of any description of capacity exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed.

S&F 1000 Ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling existing water tank, complete all as specified and directed.

S&F 20 mm bore ball brass valve high pressure with polythene float and fly nut, complete all as specified and directed.

S&F 20 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F 5 to 10 mm dia MS screw bolts (Machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut, length of bolt not exc 5 cm long, complete all as specified and directed.

S&F 100 mm long mild steel cold rolled medium weight butt hinges, fixed with MS screws, complete all as specified and directed.

S&F Wire netting of galvanised steel wire 2.00 mm dia fixed with tinned tacks of wire staples, size of mesh 20 mm, complete all as specified and directed.

S&F 100 mm long hasp & staple safety type anodised aluminium with mild steel hinge pin bolt to hinge plate and fixed with screws, complete all as specified and directed.

M&L applying 2 coats of synthetic enamel paint over a coat or red oxide zinc chromate primer on steel/iron surfaces, not exceeding 10 cm in width or girth, when unconnected with other painting or when painted in different tint, incl preparation of the new surfaces, complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white including plastic seat cover white with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

S&F in repair 10 litres capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

S&F shower rose, chromium plated brass, fancy type, 75 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed.

S&F in repairs stainless steel utensil plate rack of size 900x1000x200 mm, made of 0.60 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F in repair sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm bore superior quality PVC waste pipe and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back of size 550 x 400 mm excluding tap but including one number chromium plated brass waste fittings, 32 mm dia with long screwed shanks and fly nuts, flanged end bedded in red lead cement and other end fixed, PVC waste pipe with connector, brackets 2 numbers including cutting for and pinning in ends of brackets, complete all as specified and directed.

S&F pillar taps, cast copper alloy, with capston heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed, complete all as specified and directed.

S&F PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts & rubber washers, complete all as specified and directed.

S&F 15 mm bore bib taps, screwed down, with crutch or capstan head, chromium plated brass, fancy type, screwed for iron pipe or for unions, complete all as specified and directed.

S&F in repairs stop valves, fancy type, chromium plated brass with long shank and cup (Concealed type), screwed down, high pressure, both ends screwed to iron pipe or for union, bore of pipe 15 mm, complete all as specified and directed.

S&F in repair Angle valve, fancy type, chromium plated brass, screwed down, high pressure, screwed one end to iron pipe or union of bore 15 mm, complete all as specified and directed.

S&F in repair bib taps, cast copper alloy, fancy type, chromium plated, long body with capstan head, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket, complete all as specified and directed.

S&F in repair stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone concrete or brick surrounds, glazing with putty or fixed with beads, complete all as specified and directed.

S&F sheet glass 3mm thick ordinary quality and glazing with oil putty etc in squares n.exe 0.50 Sqm in each pane, complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes 75 mm bore, jointed in CM and taking out from trenches if required, complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes 100 mm bore, jointed in CM and taking out from trenches if required, complete all as specified and directed.

S&F sand cast iron soil, waste and vent pipe 75 mm bore in any length with or without ears with cement joints laid in trenches or in floor, complete all as specified and directed.

S&F sand cast iron soil, waste and vent pipe 100 mm bore in any length with or without ears with cement joints laid in trenches or in floor, complete all as specified and directed.

S&F 75 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F 100 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F 75 mm bore CI branch pieces, single (equal or unequal) ordinary or inverted or with parallel branches, complete all as specified and directed.

S&F 100 mm bore CI branch pieces, single (equal or unequal) ordinary or inverted or with parallel branches, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm bore round iron stays, including bolts and nuts and securing ends of stays to wall or roof, bore of pipe 100 mm, complete all as specified and directed.

Taking down shutters of any description n. exc 1 Sqm each, complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n. exc 2 Sqm each, complete all as specified and directed.

Dismantling mild steel work of any description not otherwise provided for, complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks, monkey caging for water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (2 No.) suitable handle (1 No), complete all as specified and directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal bore of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (without taking off shutters from the frame), complete all as specified and directed.

M&L for 25 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and directed.

S&F solid PVC door frame of size 50mmx 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed.

S&F 50 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type E-22, complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S&F aluminium handles, cast type, anodised 125 mm size, fixed with screws, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces, exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or stone masonry surface in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying 1 to 1.5 mm thick wall care putty as per manufacturer's instructions, complete all as specified and directed.

Preparation of old (previously treated) plastered or unplastered surfaces of walls by washing, rubbing down and stopping of distempered or painted surfaces of walls and applying two coats of distemper oil emulsion (any tint) on walls, complete all as specified and directed.

M&L applying one coat of white wash after preparation of old plastered surfaces of ceiling, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (old size fly ash bricks), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L Providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 100 mm thick as in sub base, finishing the surface even & rough to receive topping layer, complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over and including 25 mm thick sand cushion, complete all as specified and directed.

S&F in repairs 18 mm thick prelaminated MDF board, exterior grade (Grade I, type 2), one laminated with decorative choine lamination ond other side off white shade, fixed as in cupboard shutters, complete all as specified and directed.

S&F in repairs stainless steel guide channel suitable for modular kitchen basket, 500 mm long, suitable for full drawing of basket, complete all as specified and directed.

S&F in repairs 19 mm thick modular membrane kitchen cabinet door shutters (made out of MDF boards) in wood grain colour and half round edges, complete all as specified and directed.

Supply, fabrication and fixing MS tubes, medium grade with connecting plates as in posts and struts including cutting to shape, provided with necessary nuts, bolts, washers, welding etc, complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

Supply, fabrication and fixing MS tubes, medium grade with connecting plates as in framed truss, purlin, rafter etc including cutting to shape, provided with necessary nuts, bolts, washers, welding etc, complete all as specified and directed.

S&F Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete all as specified and directed.

S&F Prepainted galvalume aluminum zinc coating GI based Plain steel sheet crimped eaves and steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

S&F stainless steel utensil plate rack of size 750x900x200 mm, made of 0.60 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F stainless steel utensil plate rack of size 600x600x200 mm, made of 0.60 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F in repair 32mm bore waste coupling of PTMT (half or full threaded) minimum weight not less than 45 grams, complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F PVC (SWR) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) bend 110 mm bore, any radius with oval access door, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) vent cowl 110 mm bore, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

M&L cutting existing manholes for connecting new drain (for 100 mm bore pipe), making good to pipe and rendering, cutting out existing benching for forming branch channel (half round or 3/4 section) in cement concrete 1:2:4 type B-1 or smooth finishing, complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L preparing newly plastered surfaces of walls and applying 1 to 1.5 mm thick wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

S&F mixing valve, chromium plated brass, centre hole basin mixer, screwed and jointed to PVC connection with nuts in wash hand basin, 15 mm bore, complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.50 Cum, getting out, returning filling in and ramming earth in layers not exceeding 25 cm,watering and removing surplus soil to a distance of n exc 50m and making good surface in soft/loose soil, complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (Using 40mm graded stone aggregate) as in foundation, filling and mass concreting, complete all as specified and directed.

M&L mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh size and type to any type of standard rails, straining bolts etc, including provision of binding wire, complete all as specified and directed.

Supply only Chain link MS galvanised fencing, any size or type, complete all as specified and directed.

S&F Mild steel round bars, 10 mm bore and over, cut to length, bent to shape and provided as support to chain link fencing including necessary welding, riveting etc, complete all as specified and directed.

S&F 10 to 15 mm dia MS screw bolts (Machine made ) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut, length of bolt exc 10 cm but not exc 15 cm long, complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work new or old, like ends of posts, backs of chowkhats etc area exc 0.10 Sqm and n.exc. 0.50 Sqm and treating with tar or coal tar black paint, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L for rendering 5 mm thick on fair faces of brick work or concrete surface of ceiling in cement mortar 1:3, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of ceiling, complete all as specified and directed.

S&F continuous piano hinges, made of stainless steel, 30 mm width of flaps when open, complete all as specified and directed.

S&F brass handles, cast type, 100 mm long, polished bright, complete all as specified and directed.

S&F ball catches with 8 mm bore steel ball and brass body and striking plate including letting in and fixed, complete all as specified and directed.

S&F in repair ball valve 20 mm bore high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight not less than 210 grams) complete all as specified and directed.

S&F in repair bib tap standard of PTMT any colour, high pressure, screwed for iron pipe and fixed, 15 mm bore (minimum weight 90 gms), complete all as specified and directed.

S&F in repair 15 mm bore stop valve, Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms), complete all as specified and directed.

M&L granite slab 18-20 mm thick, table rubbed and polished in cooking platform, platform for WHB and the like, fixed over RCC slab including bull nosing to outer edges, set in CM 1:4 bedding, complete all as specified and directed.

S&F in repair pillar taps, cast copper alloy, with elbow operated head, quarter turn, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed, complete all as specified and directed.

M&L PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of walls, complete all as specified and directed.

M&L Moorum or red bajri filling in floor or paving, laid in layers, levelled and rammed including watering, complete all as specified and directed.

M&L hardcore (broken stone) of gauge not exc 63 mm, deposited spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 mix, type B1 (Using 20mm graded stone agg) as in floors finishing surfaces fair and even, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns, in floors, roofs, landing balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Formwork (rough finished surfaces) to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works, not exc 200 mm thick complete all as specified and directed.

Formwork (rough finished surfaces) to edges of concrete exc 10 Cm thick and not exc 20 Cm thick as in slabs, bands, cills, flooring etc for rough finished surfaces complete all as specified and directed.

Forming V grooves in plaster not exceeding 10 mm deep and not exc 10 mm on face, complete all as specified and directed.

M&L TMT bars, 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L TMT bars, 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Surface dressing not exceeding 15 Cm deep in soft/loose soil, complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying 1 to 1.5 mm thick Wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M&L for PCC 1:3:6 mix type C-1 (Using 20mm graded stone agg) as in bed blocks for fixing monkey caging etc, including necessary form work, complete all as specified and directed.

M&L for roughning of old concrete floors by picking, sweeping clean and washing down with wter to remove dust etc, complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surface in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for laying anti skid vitrified paving tiles of size 300x300x15 mm thick suitable for exterior areas on roof, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles, laid over and including 15 mm thick screed in CM 1:6, complete all as specified and directed.

M&L for brick work with pulverised fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed.

S&F vitreous china half stall type urinal, white with grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back with white cement, complete all as specified and directed.

S&F urinal spreader of PTMT (Minimum weight 60 Gms), any colour for fixing with 20 mm bore pipe, complete all as specified and directed.

S&F vitreous china urinal partition, white, size 310x700 mm, fixed to wall and pointing around edges in white cement, complete all as specified and directed.

S&F steel ventilators with top hung shutters including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, including one shop coat of zinc chromate primer, complete all as specified and directed.

M&L for figured glass, 3 mm thick, pin head type and glazing with oil putty in squares not exc. 0.50 Sqm in each pane complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

Dismantling water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed.

S&F 500 Ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling existing water tank, complete all as specified and directed.

S&F 'D' type towel rail 60 cm long, stainless steel, fancy type, 20 mm dia, complete fixed with stainless steel screws, complete all as specified and directed.

S&F 15 mm bore long body bib taps, screwed down, with crutch or capstan head, long shank, chromium plated brass, fancy type, screwed for iron pipe or for unions, complete all as specified and directed.

S&F PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F PVC (SWR) bend 75 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) bend 110 mm bore, any radius with oval access door, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) vent cowl 110 mm bore, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm bore round iron stays, including bolts and nuts and securing ends of stays to wall or roof, bore of pipe 75 mm, complete all as specified and directed.

M&L for 2nd class hard wood (Sal) plain, solid, straight chowkhats and frames, wrought, framed, rebated on the solid, rounded or chamfered put together with glue, pinned at joints, supplied and fixed, complete all as specified and directed.

M&L for 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Preparation of old (previously treated) plastered or unplastered surfaces of walls by washing, rubbing down and stopping of distempered or painted surfaces of walls and applying two coats of distemper oil emulsion (any tint) on walls, complete all as specified and directed.

M&L walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:4, complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling, size of grid 605x605 mm, including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and directed.

M&L for 12 mm thick fibre insulation ceiling boards, ordinary type and fixed to snap grid frame work, size of boards 600x600mm, having humidity resistence of 90%, fire performance class 'A' and surface having factory applied vinyle latex paint with back side sanded, complete all as specified and directed.

Dismantling wall and ceiling boards (plywood) or insulation boards/slabs/blankets, any thickness including cover fillets, complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in soil including spreading, leveling, watering and well ramming in layers not exc 25 Cm, complete all as specified and directed.

Removing excavated materials (soil) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above starting point, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed surfaces to match with the existing surface, complete all as specified and directed.

Disconnecting and taking down carefully ceiling fan/exhaust fan and refixing after cleaning, oiling/greasing and connecting with suitable size copper conductor cable, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including making good disturbed surface all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

One 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

One 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

One light point controlled by two 2 way 5/6 Amp switches.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including making good disturbed surface, complete all as directed and specified.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, 2 way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing switch socket combination, 5/6 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

S&F bell push single pole, AC, 240 volts, 5/6 amps, complete all as specified and directed.

S&F electronic call bell ding dong type, 5/6 Amps, 230 volts AC, complete all as specified and directed.

S&F stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 20mm, 3 terminals, complete all as specified & directed.

S&F wall mounted LED Tube light fittings, batten type with bipin holders, powder coated steel with retrofit 20 watt LED tube, internally prewired, complete all as specified and directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, complete all as specified & directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 40 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 63 Amps, Triple Pole & Neutral, 415 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed. Note for items of MCB DB - (1) The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket, complete with one single pole MCB of 32 Amps, complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 4 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. NOTE for submain wiring:- Two runs of cable, one run of earth wire and one run of PVC non metallic conduit of 25mm dia shall be measured as one run length. Cost of cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 100x100 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 175x100 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 200x150 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 250x200 mm and 50 mm deep, complete all as specified and directed.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinforced with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 5 and complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth wire upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

S&F LED security light fitting, 36 watt, pressure die cast aluminium housing with IP 66 deg of protection, complete with 1.20 m long street light bracket made of 40 mm bore GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S&F LED security light fitting, 45 watt, pressure die cast aluminium housing with IP 66 deg of protection, complete with 1.20 m long street light bracket made of 40 mm bore GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S&F 1 x 12 Watt LED doom post top lantern, made of polycarbonate, with and including electronic driver and all other accessories, complete all as specified and directed.

M&L dry clean Sand filling in trenches around underground cables for earth cushion, complete all as specified and directed. (Depth of sand shall be measured after punning).

M&L for pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), class 10, laid dry and flat adjoining each other over sand cushion in trenches as protection to UG cable, complete all as specified and directed.

M&L 40 mm bore Steel water tubing, light grade, galvanised, with all fitting, laid in trenches/fixed to walls/poles etc as protection to cables, with and including necessary MS clamps, nuts botls, washers etc required for fixing, complete all as specified and directed.

S&F LT 1100 volts grade UG cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor, 3.5 core 50 Sqmm, laid in trenches/ducts, fixed on wall/inside panel or drawn through pipe, complete all as specified and directed.

S&F recess mounted LED panel light of size 600x600 mm, 36 watt capacity and minimum 100 lumens per watt, internally prewired including all accessories, fitted to false ceiling, complete all as specified and directed.

S&F ceiling fans of 1200 mm sweep including all accessories such as down rod, canopy, blade set comprising of three blades, hanging arrangement with rubber block, nuts, bolts, washers, split pins, capacitor etc complete with and including PVC insulated twisted twin core 23/0.0076 copper conductor flexible rubber insulated cable of required length from connector/ceiling rose to fan motor including testing, commissioning and painting with black synthetic enamelled paints MES number upto 2.5 cm high, complete all as specified and directed.

S&F Exhaust fan of size 300mm sweep, 1400 RPM, metal body, complete with condenser and mounting from and regulator including providing/cutting the round hole of required size in the wall finishing the same supply and grouting the ragged bolt in wall, fixing the frame and exhaust fan including supply and fixing the louver shutter with frame on the exhaust side (outer surface of the wall) and connecting PVC insulated twisted twin core 23/0.0076 copper conductor flexible PVC insulated cable of required length from connector/ceiling rose to fan motor and engraving and painting with black synthetic enamelled paint MES number upto 2.5 cm high including testing and commisioning, complete all as specified and directed.

S AND A ENGINEERS CONSTRUCTION CO

triveni sales corporation

Aditya Enterprises

S.S Enterprises

SHREEKRISHNA INFRASTRUCTURE

K B ENTERPRISES

Pioneer Enterprises