Construction of Balance work of Uttrala to Surahi Pass (Portion Uttrala to Baklood) (Dhundhi Nallah) Km 0/0 to 13/0

Amount

Excavation in earthwork in hilly areas in all heights and depths, in all kind of soil including saturated soil comprising of mixed soil, ordinary rock and hard rock. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion, damage to hill side, water pollution, etc. and to protect stability of hill side. Rock shall be excavated with chiselling and wedging out rock (where blasting is prohibited). All earth work in cutting/excavation, including rock excavation shall be carried out true to lines, grades, side slopes, width, camber, super-elevation and levels as shown on the drawings or as directed by the Engineer-in-charge, in conformity with the requirement of technical specification clause 1603.1 and 1603.2 to achieve designed formation width including hauling and stacking of material useful for construction at suitable sites and safe disposal of unsuitable cut materials in specified manner,up to all leads & lift and finishing of the road to specified dimensions or as directed by the Engineer-in charge for smooth riding. Any loss to the public and private property during the course of excavation shall be the absolute responsibility of the contractor, which shall have to be duly compensated by him in all cases. The recovery of useful stones of 14147.18 cubic metre @ 300/- per cubic metre amounting to Rs. 4214154/- only shall be done on pro-rata basis for the quantity of cutting in earth work effected.

Earthwork in excavation for structures as per drawing and technical specification Clause 305 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal up to all leads & life dressing of sides and bottom and backfilling in trenches with excavated suitable material and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying mechanically mixed & vibrated cement concrete 1:4:8 (one cement: four sand: eight graded crushed / broken stone aggregate 40 mm (forty milimeters) nominal size ) and curing complete including the cost of form work in Retaining walls, Breast walls, in or under water complete including, pumping or bailing out water ,dewatering removal of slush as required at site which may arise at the time of laying under water complete for all heights/depths including cost of form work as per drawings and MORD technical specifications section/ clause 802, 803,1202 & 1203 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Back filling with granular material behind abutments, wing walls and return walls complete as per technical specification clauses 1206.3 & 1604.7 sandy material and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing weep holes in brick masonry/ stone masonry / plain reinforced concrete abutment , wing wall, return wall with 100mm (one hundred millimetre) diametre PVC pipe extending through the full width of the structures with slope of 1(V): 20H (one verticals : twenty horizontal) towards draining face complete as per drawing and technical specifications clauses 614,709, 1206.6 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying of boulder apron laid in wire crates with 4mm (four millimetre) diametre G.I. wire conforming to IS: 280 and IS: 4826 in 100mm x 100mm (one hundred millimetre into one hundred millimetre) mesh (woven diagonally) including 10% (ten percent) extra for laps and joints laid with stones boulders weighting not less than 25 Kg. (twenty five kilogram) each as per drawing and technical specifications clause 1301 complete and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying mechnically mixed and vibrated concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications clause 802, 803, 1202 & 1203. Plain cement concrete Grade M-10 nominal mix 1:3:6 (one cement : three sand : six graded stone aggregate 20mm (Twenty millimetre) nominal size) including cost of form work and curing complete and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and erecting a "W" metal beam Crash Barrier comprising of 3mm (three millimetre) thick corrugated sheet metal beam guard rail 70cm (seventy centimetre) above road/ ground level fixed on ISMC channel vertical posts 150 X 75 X 5mm (one hundred fifty into seventy five into five millimetre) thick spaced 2.00m (two point zero metre) centre to centre, 1.80m (one point eight zero metre) high, 1.10m (one point one zero metre) below ground/ road level, all steel parts and fitments to be galvanised by hot deep process, all fittings to confirm to IS : 1364, metal beam guard rail to be fixed on the vertical posts with a spacer of channel section 150X75X5mm (one hundred fifty into seventy five into five millimetre), 330mm ( three hundred thirty millimetre) long complete as per MoRTH specification clause 811.3 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying mechnically mixed and vibrated concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications clause 802, 803, 1202 & 1203. Plain cement concrete nominal mix 1:5:10 (one cement : five sand :ten graded stone aggregate 40mm (forty millimetre) nominal size) including cost of form work and curing complete and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying mechnically mixed and vibrated plain/reinforced cement concrete in substructure complete as per drawings and technical specifications clause 802, 804, 805, 806, 807, 1202 & 1206. Plain cement concrete Grade M-15 nominal mix 1:2.5:5 (one cement two point five sand five stone aggregate) (20mm twenty millimeter) nominal size including cost of form work and curing complete and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying flooring laid over cement concrete bedding complete as per drawing and technical specification clause 1303, cement concrete block and bedding M-15 grade nominal mix 1:2.5:5 (one cement two point five sand five stone aggregate 20mm (twenty millimeter) nominal size) including cost of form work and curing complete and to the entire satisfaction of the Engineer-in-Charge within all leads, lifts, carriage of material and other incidentials, as per direction of Engineer-in-Charge.

Providing and laying mechnically mixed and vibrated plain/reinforced cement concrete in sub structure RCC (M-20 grade stone aggregate 20mm) (twenty millimeter) nominal mix including cost of form work and curing complete as per drawings and technical specifications clause 802, 804, 805, 806, 807, 1202 & 1206 within all leads, lifts, carriage of material and other incidentials, as per direction of Engineer-in-Charge.

Providing and laying mechnically mixed and vibrated plain/reinforced cement concrete in sub structure PCC (M-20 grade stone aggregate 20mm) (twenty millimeter) nominal mix including cost of form work and curing complete as per drawings and technical specifications clause 802, 804, 805, 806, 807, 1202 & 1206 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying mechnically mixed and vibrated reinforced cement concrete in super structure as per drawing and technical specifications Clause 1401 RCC Grade M-25 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying mechnically mixed and vibrated reinforced cement concrete in super structure as per drawing and technical specifications Clause 1404.4 i/c cost of cement reinforcement M-30 RCC Grade M-25 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying mechanically mixed and vibrated reinforced cement concrete M-30 (M-thirty) design mix with cement contents not less than 430 Kg (Four hundred thirty kilogram) per cubic metre with 20mm ( Twenty milimetres) crushed stone aggreagate in super structure as per drawings and M.O.R.D. technical specification section 800, 900,1000 and 1400 including the cost of form work and reinforcement for reinforced concrete work in wearing coat and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Construction of RCC railing of M-25 (twenty five) grade in cast -in-situ with 20 (twenty) millimeter nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500 (one into five hundred), centre-to-centre spacing between vertical posts not to exceed 2000 (two thousand) millimeter as per drawing and technical specification Clause 1404.3 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Supplying, fitting, and placing HYSD bar reinforcement in sub structure including cutting, bending, binding and placying in position complete as per drawing and technical specifications clauses 1001, 1206 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Supplying, fitting, and placing HYSD bar reinforcement in super structure including cutting, bending, binding and placying in position complete as per drawing and technical specifications clauses 1001, 1401 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and fixing drainage spouts complete with 100mm (One hundred milimetres) dia galvanised mild steel down pipe corrosion resistant structural steel grating complete as per drawing technical specification Clause 1404.5 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge.

Providing and laying mechanically mixed and vibrated concrete for plain/reinforced concrete in below approach slab for all types of structure complete for (PCC) plain cement concrete grade M-15 (M Fifteen) grade design mix with minimum cement contents of 275 kg( two hundred seventy five kilogram) per cubic metre leveling course below approach slab completed including curing complete including pumping or bailing out water ,dewatering and removal of slush as required at site which may arise at the time of laying concrete for all heights/depths including cost of form work in complete in levelling course as per drawings and MORD technical specification Clause 1404.4 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Loosening of the ground up to a level of 300 (three hundred) millimetre below the sub grade level, watered, graded and compacted in layers to meet requirement for sub grade as per technical specification Clause 303 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement as per Technical Specification Clause 303 complete and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Construction of granular sub-base conforming to gradings of Table 401.1A, spreading in uniform layers with tractor mount grader on prepared surface mixing by mix in place method with rotavator at OMC and compating with smooth wheel roller to achieve the desired density, complete as per technical specification Clause 401 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing, laying, spreading and compacting stone aggregates by manual means of 63 to 45mm (sixty three into forty five) millimetre specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN (eighty-hundred kilo newton) static roller in stages to proper grade and camber, applying and brooming stone screening/ binding materials to fillup the interstics of course aggregate, watering and compacting to the required density Grading-2 (two) as per technical specification clause 405 complete and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing, laying, spreading and compacting stone aggregates by manual means of 53mm to 22.4mm (fifty three into twenty two point four) millimeter sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN (eighty-hundred kilo newton) static roller in stages to proper grade and camber, applying and brooming, stone screening/ binding materials to fillup the interstics of coarse aggregate, watering and compacting to the required density Grading-3 (three) as per technical specification clause 405 complete and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and applying priming coat with bitumen emulsion (SS-I) at the rate of 0.70 -1.00 kg (zero point seven zero - one point zero kilogram) per square metre on prepared surface of granular base including cleaning of road surface with mechnical broom as per technical specification clause 502 including hauling of material with in all leads and lifts by all modes of transportation and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and applying tack coat with bitumen emulsion (RS-I) at the rate of 0.25 -0.30 kg (zero point two five - zero point three zero kilogram) per square metre on granular surface treated with primer coat cleaned with hydraulic broom as per technical specification clause 503 including hauling of material with in all leads and lifts by all modes of transportation and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and applying tack coat with bitumen emulsion (RS-I) at the rate of 0.20 -0.25 kg (zero point twenty : zero point twenty five kilogram) per square metre on granular surface treated with primer coat cleaned with hydraulic broom as per technical specification clause 503 including hauling of material and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and laying bituminous concrete with 60-80 (Sixty - Eighty ) TPH batch type hot mix plant producing an average output of 50 (fifty) tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 (five point four : five pont six) per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tendem rollers to achive the desired compaction as per MORTH specification clause 507 complete including hauling of material and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement mechanically mixed and vibrated and curing complete, thickness as per design, over a prepared sub base, with 43 (forty three) grade cement or any other type as per Clause 1501.2.2, M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25mm, mixed in a concrete mixer of not less than 0.2 cum (zero point two cubic metre) capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 (one hundred twenty five) micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 complete and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and Fixing reinforced cement concrete M-15 grade kilometre stone / 200m stone of standard design as per IRC:8/ IRC 26, fixing in position including painting and printing, etc as per drawing and technical specification clause 1703 through all modes of transportation and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

5th Kilometre Stone

Ordinary Kilometre Stone

200 Metre Stone

Semi Reflective Traffic Signs Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701 fixed over aluminium sheeting, 1.5 (one point five) millimetre thick supported on a mild steel angle iron post 75mm x 75mm x 6mm (seventy five into seventy five into six) millimetre firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm (four hundred fifty into four hundred fifty into six hundred ) in 600, millimetre below ground level as per drawings and technical specification clause 801, 1701, millimetre equilateral triangle / circular / rectangular and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Direction and Place Indentification signs up to 0.9 sqm size board. Providing and erecting direction and place identification retro-reflectorised sign as per IRC: 67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 (two) millimetre thick with area not exceeding 0.9 (zero point nine) square meter supported on a mild steel single angle iron post 75 x 75 x 6 (seventy five into seventy five into six) millimetre firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450mm x 450mm x 600mm ) four hundred fifty into four hundred fifty into six hundred) 600 (six hundred) below ground level as per approved drawing and Technical Specification Clause 1701 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and erecting direction and place identification retro-reflectorised sign as per IRC: 67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 (two) millimetre thick with area exceeding 0.9 (zero point nine) square meter supported on mild steel langle iron posts 75 mm x 75mm x 6mm (seventy five into seventy five into six) millimetre 2 Nos. firmly fixed to the ground by means of properly designed foundation with M-15 (fiteen) grade cement concrete 450mm x 450mm x 600mm (four hundred fifty into four hundred fifty into six hundred ) millimetre, below ground level as per approved drawing and technical specification clause 1701 and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Providing and Fixing reinforced cement concrete M-15 boundary stone of standard design as per IRC: 28, fixing in position including painting and printing, etc as per drawing and technical specification clause 1704 through all modes of transportation and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge .

Laying Cooncrete Cradle Bedding with M-15 Grade with cement concrete as per clause 1101 .5 (i)

Providing and laying 900mm (nine hundred millimetre) dia meter reinforced cement concrete pipe NP3 for culverts on concrete cradle bedding in single row including fixing collar with cement mortar 1:2 (one cement two sand) but excluding excavation, protection works, backfilling, concrete and masonary works in head walls and parapets as per clause 1101 complete and as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals and to the entire satisfaction of the Engineer-in-Charge.

Routine maintenance after completion of construction work including hauling/ carriage of all labour, equipment and materials to various locations of site through all modes of transportation in all leads and lifts to the entire satisfaction of Engineer-in-Charge.

For 1st Year

For 2nd Year

For 3rd Year

For 4th Year

For 5th Year

P. L. SHARMA