Electrification work for 16 Nos. of Type IV Quarters at 1st, 16th and 17th Avenue at NMPA

Supplying and wiring adopting loop system in existing PVC conduit using 2x1.5sqmm & 1x1.0sqmm FRLS multi strand PVC insulated copper wire without control switch shall be fixed on the plastic sheet / gang box, the other end of the wires shall be terminated with sufficient loose length in a wood block /PVC round block complete for each outlet. a) Short point.

Supplying and wiring adopting loop system in existing PVC conduit using 2x1.5sqmm & 1x1.0sqmm FRLS multi strand PVC insulated copper wire without control switch shall be fixed on the plastic sheet / gang box, the other end of the wires shall be terminated with sufficient loose length in a wood block /PVC round block complete for each outlet. b) Medium point.

Supplying and wiring adopting loop system in existing PVC conduit using 2x1.5sqmm & 1x1.0sqmm FRLS multi strand PVC insulated copper wire without control switch shall be fixed on the plastic sheet / gang box, the other end of the wires shall be terminated with sufficient loose length in a wood block /PVC round block complete for each outlet. c) Long point.

Supplying heavy gauge PVC conduit pipe 25mm dia 2mm thick with suitable size bends, junction boxes adhesive paste etc and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures and run with 18 swg GI fish wire wherever necessary.

Supplying heavy gauge PVC conduit pipe 25mm dia 2mm thick with bends, Junction boxes adhesive paste, by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering up to the surface of the brick level and run with 18 swg GI fish wire run throughout the conduit wherever necessary.

Supplying and fixing 25mm PVC casing and capping on the wall or ceiling using necessary materials like bends, junction boxes, elbows, screws at an interval of 300mm. etc. as required.

Supplying of 4 feet LED batten with LED tube 20W with high quality diffuser with life of 25000 burning hours and 70% lumen maintenance with CRI > 80. Power input 220-240V @ 50Hz and power factor >0.9 along with CE approved.

Fixing LED Fittings indoor on the wall/ceiling using approved make 23/0.0076” twin twisted PVC insulated wires required No of ceiling rose/ round blocks and clamps.

Supplying capacitor type decorative 48” sweep ceiling Fan complete with down rod, blades, shackle, caNopies etc for operation on 230V, 50Hz, single phase AC supply confirming to ISS-374-1979 and with double ball bearing system and as per technical data approved.

Fixing a ceiling fan of all capacities and all types to the existing S hook with fan regulator to the existing board with 5A Ceiling rose of approved quality with necessary length of 23/0.0076” PVC insulated twin twisted copper wire and wiring complete.

Supplying and fixing of Slant holder with 9W LED Bulb. LMR

Supplying and fixing of LED Bulkhead of 10W with IP65 protection and IK 08 impact resistance suitable for surface and wall mounting applications.

Supplying and fixing Metal Fan Box with Round Hook.

Extra length of GI pipe of class B 19mm dia for down rod.

Supplying and wiring for lighting /power circuit using FRLS PVC insulated 1100 grade, multi strand copper low conductor resistance single core wire in concealed system of wiring. a) 1.5 sq.mm wire

Supplying and wiring for lighting /power circuit using FRLS PVC insulated 1100 grade, multi strand copper low conductor resistance single core wire in concealed system of wiring. b) 2.5 sq.mm wire

Supplying and wiring for lighting /power circuit using FRLS PVC insulated 1100 grade, multi strand copper low conductor resistance single core wire in concealed system of wiring. c) 4.0 sq.mm wire

Supplying and wiring for lighting /power circuit using FRLS PVC insulated 1100 grade, multi strand copper low conductor resistance single core wire in concealed system of wiring. d) 6.0 sqmm wire

Supplying and flush mounting powder coated metal box suitable for fixing mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in brick / stone / cc wall. a) 1 Way

Supplying and flush mounting powder coated metal box suitable for fixing mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in brick / stone / cc wall. b) 2 Way

Supplying and flush mounting powder coated metal box suitable for fixing mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in brick / stone / cc wall. c) 3 Way

Supplying and flush mounting powder coated metal box suitable for fixing mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in brick / stone / cc wall. d) 6 Way

Supplying and flush mounting powder coated metal box suitable for fixing mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in brick / stone / cc wall. e) 8 Way

Supplying and flush mounting powder coated metal box suitable for fixing mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in brick / stone / cc wall. f) 10 Way

Supplying and flush mounting powder coated metal box suitable for fixing mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in brick / stone / cc wall. g) 12 Way

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required No’s of machine screws, bolts and nuts etc complete on the existing PVC box. a) 1 Module

upplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required No’s of machine screws, bolts and nuts etc complete on the existing PVC box. b) 2 Module

upplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required No’s of machine screws, bolts and nuts etc complete on the existing PVC box. c) 3 Module

upplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required No’s of machine screws, bolts and nuts etc complete on the existing PVC box. d) 6 Module

upplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required No’s of machine screws, bolts and nuts etc complete on the existing PVC box. e) 8 Module

upplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required No’s of machine screws, bolts and nuts etc complete on the existing PVC box. f) 10 Module

upplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required No’s of machine screws, bolts and nuts etc complete on the existing PVC box. g) 12 Module

Supplying and fixing of modular type materials on existing modular switch plates. a) 6A Switch

Supplying and fixing of modular type materials on existing modular switch plates. b) 6A 2 Way Switch

Supplying and fixing of modular type materials on existing modular switch plates. c) 6A 3 Way Socket

Supplying and fixing of modular type materials on existing modular switch plates. d) Stepped Fan Regulator 2 Module

Supplying and fixing of modular type materials on existing modular switch plates. e) 16A One Way Switch

Supplying and fixing of modular type materials on existing modular switch plates. f) 6A Bell Switch

Supplying and fixing of modular type materials on existing modular switch plates. g) 32A DP Switch

Supplying and fixing of modular type materials on existing modular switch plates. h) 6/16A Universal Socket

Supplying and fixing of following modular type materials on existing modular switch plates. i) TV Socket

Supplying and fixing of modular type materials on existing modular switch plates. j) Blanking Plate

Supplying and fixing regular Double door MCB distribution boards flush mounting with provision for fixing suitable type capacity MCB’s single phase /3 phase with powder coated painting. Made out 14 SWG MS enclosure. a) 16 Way SP & N.

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and wiring complete as required. a) 6A SP MCB

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and wiring complete as required. b) 20A DP MCB

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and wiring complete as required. c) 40A DP MCB

Supplying and running copper conductor 12 SWG for grounding and using necessary suitable size clamps, nails etc complete.

Supplying, fixing and wiring earth electrode for grounding using 40mm dia, 2.90mm thick GI pipe 2.5 mtr long with GI funnel with mesh and suitable size reducer fixed on the top of electrode. The funnel should be enclosed in a cc chamber of 400 x 400 x 400mm with a cast iron cover.the earth electrode shall have staggered holes of 12mm dia and the electrode should be covered 150mm alround with alternate layers of salt and charcoal from the bottom of the CC chamber.

Supply and Installation/ Fixing/ of 300x600x170mm, Provision of Outdoor type Thermoplastic Modular Panel enclosure with transparent Polycarbonate Lid, shock proof, IP 65 (Weather proof), rust proof, dust proof, water proof, corrosion proof having internally Embedded gasket on both lid and flap with suitable transparent hinged flap opening for operating MCB.

Providing 20mm cement plaster with cement mortar 1:3 finished with a floating coat of neat cement to brick/ stone machinery including rounding of corners wherever required smooth rendering, providing and removing scaffolding including cost of materials, labour, curing complete as per specifications.

Supplying and drawing PVC insulated gas injected physical foam jelly flooded co-axial TV cable RG-6.

Supplying and fixing and wiring Electronic Trivector meter 5 to 30A single phase Class-1 Accuracy with Tamper Proof Energy Meter.

Supplying and fixing one of 230V Ding Dong bell and a flush type bell push with gang box fixed on necessary wooden plugs using NF screws.

Supplying a 15 litres capacity vertical type wall mounting Electrical water heater with 2KW capacity element with a neon indicator fitted with 20 A capacity 25 to 85 degree centigrade range thermostat. The water heater shall completely be wired with 40/0.0076” 3core copper flexible wire of 1.5 Mtrs length and the outer container provided with heavy gauge brackets for wall mounting.

Erection charges for fixing a 15 ltr capacity wall mounting electric geyser using bolts and nuts and wiring with 15A 3 pin top.

Removing and releasing of existing old electrical fixtures and old wiring and shifting to the Sub Division office.

Supplying of 4Cx16 sqmm 1.1KV class LT UG cable XLPE insulated, PVC extruded inner sheath armoured UG cable as per IS 1554.

Labour charges for laying of 4Cx16 sqmm 1.1KV class LT UG cable in existing trench/wall/pipe as required.

Earth escavation for cable trench of 0.6mtr deep x 0.5mtr wide refilling the trench to the required ground level and consolidating and depositing of surplus earth with a lead of 200mtrs etc, complete. In hard soil.

Supplying and laying of 50mm PVC conduit pipe (Blue color)

Cutting of road for cable trenches and depositing of the excavated earth as directed barricading and refilling the trench and consolidating and depositing of surplus earth with a lead of 200 mtrs etc complete. a) Tar road

Providing and filling sand in excavated trench to cover already laid UG cable to a depth of 150mm around the cable.

Supplying and laying of Semicircular (C-cut) RCC pipes of 150mm dia, 25mm thickness and 1metre length

Supplying of RCC Hume pipe 2000mm long 150mm dia.

Laying of hume pipe fixing collars etc complete.