SPECIAL REPAIR BUILDING NO P-5/01 TO P-5/07 (07 x OR MD ACCN) OF 58 COY ASC DEPOT UNDER GE(N) AHILYANAGAR

Amount

Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor and removing all rubbish/dismantled material outside MD Land. all as directed.

Demolition of plain cement concrete (unreinforced) in ground floor and paving not exceeding 15 cm thick all as directed.

M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base all as directed.

M&L for Glazed colour ceramic tiles 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured as approved by GE as in dado / skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,(300x300)mm as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for Non skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,(400x400)mm as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for ceramic light shade coloured tiles 8-10 mm thick as approved by GE (square /rectangular) area of each tile not exceeding 0.36 sqm,(600 x600)mm as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed

-Ditto- all as per ser item No 07 above but on skirting and backing coat of 10 mm thick in CM 1:4

M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engineer-in-Charge

M&L for 15mm-18mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills, jambs, lintel etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in CM 1:4 jointing , pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and directed.

M&L for machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all as directed.

M&L for 20 mm thick Rough dressed(shahabad) lime stone slab flooring, laid dry, jointed and pointed in cement mortar 1:3 as in floor/plinth etc over bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 in floor/plinth etc over and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed

Fixing only 20mm thick rough dressed Shahabad stone as in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 including dismantling complete all as specified and directed

Demolition of brickwork/ stone/ boulder masonary/plain cement concrete solid block masonary built in cement mortar & removing all rubbish/dismantled material outside MD Land.all as directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge

Extra over stone walling for hammer dressing to face stones with maximum depression on face beds and joints from straight edge held against the dressed surface n exc.40 mm and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses.

M & L for pre-cast cement concrete solid blocks, exc. 10 cm in width type C-5 1:5:10 using 20 mm graded aggregates and setting in mortar 1:6 complete all as directed.

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water all as directed

M&L for rendering, 12 mm thick on stone surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed.

M&L for rendering, 10 mm thick on brick/concrete surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed.

M&L for rendering, 15 mm thick on stone/brick/ concrete surfaces in cement mortar 1:4 surfaces finished even and fair without using extra cement all as specified and directed.

M&L for preparing new unplastered or plastered surfaces and applying two coats of oil bound distemper including a wall care putty before applying chalk whitening on wall including smooth roller finish complete all as directed.

M&L for preparation of newly plastered surface of wall and apply two coats of cement based paint over a coat of alkali primer any height including scaffholding etc complete all as directed.

M&L for complete removal of existing treatment, washing, rubbing down and stopping old distempered and apply a coat of wall care putty over the surface of walls and applying two coats of oil bound distempering on walls all as directed.

M&L for preparation of old plastered or unplastered surface of walls including cornices etc by brooming down or steel wire brushing scraping down smook soot,moulds,moss and efflorescent salt,trading oil and greasy spots and apply applying two coats of cement based paint all as directed.

M&L for preparing old painted surfaces of wall and applying one coats of cement based paint all as directed.

M&L for preparation of old surfaces of wood of any description exc 10cm width/girth incl cleaning applying one coat of synthetic enamel all as specified directed by Engineer-in-charge.

M & L for preparation of old steel and iron surfaces, of any description, over 10 cm width or girth not other wise described and applying one coats of synthetic enamel paint over a coat of red oxide primer

Dismantling timber scantling 40 sqcm and over in section, in any postion framed work as in scanging of main joist of roof & removing all rubbish/dismantled material outside MD Land.

-ditto- all as ser item no.30 above, but in fillets, rails, posts, rafters purlins etc under 40 sqcm in section framed work & removing all rubbish/ dismantled material outside MD Land.

Dismantling battens for tiles, shingles etc of any size including tilting fillets spacing exc 15 cm &removing all rubbish/dismantled material outside MD Land.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, including ridge & removing all rubbish/dismantled material outside MD Land.all as directed.

S&F Pre-painted Galvalume sheet shall be 0.50mm thick, 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge.

Supply and fix Pre-painted 0.50 mm thick plain, galvanised sheet in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with, 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge.

S&F Steel work in tubular trusses Roof trusses (framed) of section Rectangular/ square/ circular, post, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 2014 and IS 4923- 2017 grade St.-240

S & F Aluminium wind ties (40x3) mm for roof including securing bolts; as directed, drilling holes,notching for wire, etc.;including all necessary drilling, bolting or riveting, etc.,and similar work complete all as specified and directed by Engg-In-Charge.

M & L for filleting in any position in repairs and to any shape in cement and sand mortar (1:4) including all mitres, stops etc exc 25 Sqcm but n.exc 50 Sqcm etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed.

Supply and fix in repairs wash hand basin vitreous China, flat back of size 550 X 400 mm including a pair of brackets, PTMT waste coupling, 32 mm dia PVC flexible waste pipe and connecting to stop valve and nahani trap all as directed.

Taking down chowkats or frames exc 1.5 Sq m but nexc 4.00 sqm with shutters (without taking off shutters from the frames) all as directed.

Taking down chowkats or frames n exc 1.5 Sq m with shutters (without taking off shutters from the frames) all as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each all as specified directed by Engineer-in-charge.

Taking down shutters of any description n exc 1 sqm each all as specified directed by Engineer-in-charge.

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified,

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

Supply and fix 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed.

M&L Second class hardwood 35 mm Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, all as directed.

Supply and fix Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face

Supply and fix stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples all as directed.

Supply and fix for 3 mm thick sheet frosted/pin headed in squares n exc 0.50 sqm in each pane

Supply and fix mild steel butt hinges medium weight cold rolled of size 100mm

Supply and fix aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section of cast aluminium alloy and fixed 300mm long.

Supply and fix aluminium anodised barrel tower bolt of extruded section 200mm long.

Supply and fix aluminium anodised handles of extruded section 150mm long.

S&F in repair 300mm mild steel ordinary rat tail rod patteren door spring including roller and roller plate complete all as specified and directed

S&F in repair 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of pink primer for new wooden surfaces of any description exc 10 cm width or girth including preparation of surfaces and smooth finish with roller all as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer for new steel surfaces of any description exc 10 cm width or girth including preparation of surfaces all as directed.

Supply and fix mild Steel 20 mm dia decorative powder coated curtain rods with fixing brackets fixed in repairscomplete all as specified and directed.

Supply and fixed in repairs 32 mm dia PVC waste pipe(outlet pipe) plain fixed to waste coupling of WHB or Sink etc all as directed.

Supply and fix in repairs stainless steel kitchen sink matt finish with made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed.

S&F stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 36''x 36''x 10'' with complete accessories including screws etc complete all as specified and directed by Engineer-in-Charge .

S&F in repairs for false ceiling with vinyle faced Arn-GYP-FB, celing 600 x 600 x 7-8 mm thick with washable metallized polyster foil backing with vinyle covered edges supporting sections shall be of sutable size from same makes embossed on section and level adjuster duly suspended by 2mm dia GI wire fixed to roof at 600mm center to center as per manufacturere,s instruction and all as directed Make : Armstrong or equivalent in Saint Gobin/Lafarge

Supply and fix in repair health faucet with 15 mm dia 1.25 m long flexible tube wall mounted / hooked including making connection and fixed in position complete all as specified and directed by Engg-in-charge

Supply and fix in repair bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule all as directed.

Supply and fix in repairs stop valve cast copper alloy, fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore

Supply and fix in repair 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

Supply and fix in repairs, shower rose with shower arm

Hacking out old broken glass (any thickness size,quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads n'exc 1.5 Sqm.

M&L for glazing with 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane all as directed.

Supply and fix in repair stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples all as directed.

Supply and fix in repairs rotational moulded polyethylene water storage tanks Tripal layer (cylindrical vertical with closed top) of 1000 litres capacity hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with Stainless steel Nuts of length 600mm

S&F in repair for stainless steel grating without waste holes 100 mm dia

S&F in repair for stainless steel grating with waste holes 100 mm dia

S&F for PVC (SWR) floor trap, plain with grating including jointing with solevent cement 75 mm bore

S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- all as per ser item no 80 above but as in trenches or floor

S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- all as per ser item no 82 above but as in trenches or floor

S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore

S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore

S&F PVC (SWR) vent cowl110mm bore

S&F for low density polyethelene pipes 32 mm bore (LDPE) of pressure rating 6 Kg/cm² laid in trenches/fixed to wall

Supply and fix in repairs 10 L PVC valveless, syphonic action type, flushing cistern, low level, all accesories all as directed. Make :- Sleek essence series Of Hindware or Cat part No E8303 Of Parryware .

Taking up or down steel tubing and connections,15 mm bore

.-Ditto- all as per ser item no 92 above but 20mm bore

S&L of CPVC pipes SDR 11 including fittings in trenches, 16mm outer dia fixed to walls /ceiling or laid in trenches incl all necessary fittings.

.-Ditto- all as per ser item no 94 above but 20mm outer dia etc

S & F standard aluminium section powder coated (minimum thickness of powder coating shall be 50 micron and colour shall be approved by GE) as in frame,shutter for doors, windows/ ventilator, partitions, fixed/ openable/ sliding or in any pattern, cut to size,jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass,provision of hinges, screws, plugs, handle, lock, roller, nylon ball bearing etc complete all as specified and directed. (Aluminium section shall be of make Jindal/Hindalco/Indalco) Note : Weight of Aluminium sections as per actual or as per IS or as per manufacturer,whichever is less, shall only be considered for payment.Cost of other items/ accessories required for entire completion of the work shall be deemed to be included in the quoted rate.However glass panes and wire cloth shall be measured and paid seperately as supply only under respective items.

Fixing only for framed work such as guard bars/ grill /gratings etc with ends of bars shouldered and/or riveted or gorged into spikes confroming to FE-290, Gde -E- 165

Supply and fix tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets etc complete all as specified and directed by Engineer-in-Charge

Cutting out of shrubs, kerbs and small plants of stem n exc 30 cm girth measured 1 m above average ground level including cutting of grass and removing rubbish material like branches, leaves, grass and garbbage to clear the alignment of existing seage /drainage line to make site workable condition and making good the disturbed ground complete all as directed

M&L for 150mm bore Reinforced cement concrete pipe, type NP-2 laid in trenches and jointed as specified, making necessary connections after cutting into existing sewer line /manhole to make it functional after taking down/out salt glazed ware, AC or reinforced concrete pipe as existing at site complete all as specified and directed.

.-Ditto- all as per ser item no 100 (here-in-before) but 200mm bore pipe

.-Ditto- all as per ser item no 100 above but 300mm dia RCC pipe

Supplying and fixing precast manhole cover (LD) of size 12" x 36" made up of steel fibre reinforced concrete M-30 grade as per IS etc complete all as specified and directed by Engineer-in-Charge Note : Make and material shall be as approved by GE.

.-Ditto- all as per ser item no 103 (here-in-before) but of size 12" x 48" etc.

Cleaning/ desludging of existing Manhole/ septic tank of any capacity/ sump well of any dia and depth incl taking out sludge in any form and other foreign matter etc viz sediment, sand, ash, grease, fibre, silt, roots or vegetation etc, cleaning the premises using chlorine powder etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs looking mirror of size 600 mm X 450 mm etc complete all as specified and directed by Engineer-in-charge.

Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Charge.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories PVC boxes (upto 12 module suitble for Mylinc series of Legrand including white plates with frame upto 12 module of make suitable for Mylinc Series ) for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2.Wiring shall be done as per complaints recd from user only on required basis it is not necessary to do whole wiring of any whole bldg 3. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, ceiling lights, bulkhead lights, bldg security light etc

One light point controlled by switch 5 Amp single pole one way

One fan point controlled by switch 5 Amp single pole one way

One bell point controlled by switch 5 Amp single pole one way

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

.-ditto- all as per ser Item No 108 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase , Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board

S&F in replacement bell ding dong elelctric 230V AC single pole etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Switch, 6 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Switch, 16 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Socket Outlet 6 Amp, 3 pin, combined two module etc complete all as specified and directed by Engineer-in-Charge.

S&F Modular Socket Outlet 6 Amp / 16 Amp - 2/3 pin combined two module etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Bell push, 6 Amp, one module etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Fan Regulator Fan step regulator, 120 Watt - two module etc complete all as specified and directed by Engineer-in-Charge

Supply & fix lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

S&F ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge

S & F in replacement double door Sheet metal enclosures factory made DBs 4 way TPN, 415 volts ,protection class IP-42, suitable for fixing of MCBs etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

S & F in replacement double door Sheet metal enclosures factory made DBs SPN, 8 way ,240 volts ,protection class IP-42, suitable for fixing of MCBs,, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

Supply & fix MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fix MCBs, TPN, AC, 415 volts of 63 Amps capacity 10 KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix MCBs, SPN, AC, 240 volts of 40 Amps capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge.

S&F in replacement square profile LED lighting fixture , environmental friendly, energy efficient ready to use pack Aluminium housing LED Tube light fitiing 20 Watt with LED light source 6500 K,input voltage 160V-270V with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge .

Supply & fix in replacement energy saving and environmental friendly long life LED street light 25 Watt (Bldg security light) made up of pressure die cast aluminium housing with mild power LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 fixed on wall with GI pipe of suitable dia and all fixing accessories including connecting up with & including twin core twisted flexible copper conductor cable of suitable size of 230V , 50 HZ etc complete all as specified and directed by Engineer-in-Charge

S&F sub main wiring with two single core PVC insulated, unsheathed, FRLSH stranded copper conductor cable 4 Sqmm with 4 Sqmm PVC insulated, unsheathed, FRLSH stranded copper conductor cable as earth wire drawn through and including PVC Casing and capping ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge . Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. Two run of 4 Sqmm cable i.e for one run for phase, one run for neutral with one run of 4 Sqmm cable for earth and one run of PVC Casing & caping shall be measured as one unit

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. Earth pit not less than 2.25 m depth and top edge of the earth plate not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nuts, bolts & washer etc. Earth wire connected upto main earth point / DBs alongwith 15mm dia earth protection pipe from top edge of the earth plate to main earth point to be connected and 20mm dia watering pipe light grade with funnel and provn of PCC using cement concrete (1:2:4) mix type B1 using granded stone aggregate and RCC pit cover 50 mm thick precost RCC (1:2:4) mix type B1 duly reinforced with 8 mm dia of TMT bar @ 100 mm CIC, both way, lifting arrangement complete including all necessary earth work etc complete all as specified and directed by Engineer-in-Charge

Supply and fix exhaust fan, steel body AC Single phase, 230 V of size 380mm sweep with, blades and frame and heavy duty all as specified and directed by Engineer-in-charge

Taking out/down and opening of existing ceiling fans 1200 mm sweep/exhaust fan of any size/ electric meter from any position, of any make etc & refixing at the desired location after reassembling and after servicing/overhauling by thouroghly cleaning the shaft,rotor,stator and applying lubricant/grease to bearings and one coat of super enamelled varnish over winding to improve the insulation resistance including repair /replacement of spare parts/ material /items , making connection by replacing PVC insulated unsheathed cable of copper conductor of size 1.50 Sqmm upto 0.50 Mtr length including using material/parts of minor nature such as screws, lugs, insulation tape, nuts, bolts, washers etc after cleaning the metal surface, greasing/ lubricant etc to make it functional complete all as specified and as directed.

M/S MAHESHWARI ENTERPRISES (BID ID -3489963)

MATOSHREE CONSTRUCTION (BID ID -3491460)

Ms. S.K. ASSOCIATES (BID ID -3489905)

HG PATHAN CONSTRUCTION COMPANY (BID ID -3491364)

M/S. Z.K.ENTERPRISES, AHMEDNAGAR (BID ID -3490006)

PRADIPKUMAR POPATRAO THUBE (BID ID -3490026)

AZAD SERVICES (BID ID -3491966)