Rate contract of Repairing, Maintenance & SITC of Electrical Accessories at West Zone Halls & Party Plots of AMC. (Within the limit of Amount Rs.10.00 lacs)

(Technical Bid only) of Tender

Office, Mezzanine Floor, “B”-Block,

in Physical form Sardar Patel Bhavan, Danapith,

Ahmedabad-380001.

4 Tender Vol-I (Technical Bid on 08/09/2026, 04:05 pm onwards

only) Opening Date, Time and Online Opening:- At the Office of

Place Additional Chief Engineer(Electrical),

Light Department, 5th Floor, “C”-Block,

Sardar Patel Bhavan, Danapith,

Ahmedabad-380001.

Physical Opening:-At the Office of Tender

Officer, Central Record Office, Mezzanine

Floor, “B”-Block, Sardar Patel Bhavan,

Danapith, Ahmedabad - 380001 or at

the above said office.

MUNICIPAL COMMISSIONER

Ahmedabad Municipal Corporation

Sardar Patel Bhavan,Danapith

Price Bid (FOR REFERENCE ONLY)

Tender for Rate contract of Repairing, Maintenance & SITC of Electrical

Accessories at West Zone Halls & Party Plots of AMC. (Within the limit of Amount

Sr No Item Description Unit Qty Rate in Rs.

Point wiring for Light / Fan/ Bell /

Primary Point with 2-1.5 sq. mm & earth

wire of 1.5 sq. mm (green) both are of ISI

marked 1.1 kv grade FRLS PVC

insulated multi strand copper wires upto

max length of 10 mtr in below type of

pipe erected with 6A Tissino Type ISI

marked flush type switch / bell push

and accessories erected on Metal / PVC

/ Wooden Box covered with 3 mm thick

PC(Polycarbonate) / Acrylic / Laminated

sheet. with necessary Lamp holder /

ceiling rose / H.D. Connector as

(e) in existing pipe erected flushed on

wall / ceiling complete

Point wiring for independent PLUG with

following size mains earth wire of

sq.mm (green) both are of ISI marked

KV grade FRLS PVC insulated multi

strand copper wires upto 10 mtr length,

in following below of pipe erected

complete with ISI marked 3/5 Pin socket

and tissino type switch erected with

2.0 earth continuity connection erected on Pt

Metal / PVC / Wooden box covered with

3 mm thick PC(Polycarbonate) / Acrylic

/ Laminated sheet.

[A] For 6 amp plug and 6 amp switch

with 2-1.5 sq. mm Cu. Mains from near

by switchboard/db board upto 6 mt.

(e) in existing pipe erected flushed on

wall / ceiling complete

Same as Above for-

[B] 6/16A Plug and 16 amp switch with

2-2.5 sq. mm Cu. Mains from mcb db

(e) in existing pipe erected flushed on

wall / ceiling complete

Point wiring for on board looped PLUG

with tissino type single pole ISI marked

Switch and Socket erected with

necessary connections erected on

4.1 wooden / Metal / PVC Box covered with Pt

3 mm thick PC(Polycarbonate) / Acrylic

sheet for open / concealed wiring for

following size.

4.2 Same as Above for- Pt.

Point wiring for Light / Bell with 2-1.5

sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in

below type of pipe erected with 6A

Modular type switch / bell push &

accessories and earth continuity of

5.0 following type, erected on PVC / Metallic Pt.

/ Wooden box, single mounting base

frame covered with textured / metallic /

white front plate modules erected on / in

wall / ceiling as per pipe erected, with

necessary Lamp holder / ceiling rose /

H.D. Connector as directed.

(e) in existing pipe erected flushed on

wall / ceiling complete Cat III

Point wiring for FAN with 2-1.5 sq.mm &

earth wire of 1.5 sq.mm (Green) both are

of ISI marked 1.1 KV Grade FRLS PVC

insulated multi strand copper wires up

to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and

hum free EME step type electronic fan

regulator mounted and accessories with

6.0 earth continuity of following type erected Pt.

on PVC / Metallic / Wooden box, single

mounting base frame covered with

textured / metallic / white front plate

modules erected on / in wall / ceiling as

per pipe erected with necessary ceiling

rose / H.D. Connector as directed.

(e) in existing pipe erected flushed on

wall / ceiling complete Cat III

Point wiring for Individual Plug with &

earth wire of 1.5 sq.mm (Green) both are

of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up

to 10 mtr length, in below type of pipe

erected complete with Modular type

switch & 5 pin Plug erected on PVC /

Metallic / Wooden box covered with

appropriate front plate modules erected

on / in wall / ceiling as per pipe erected

with following type of accessories.

[I] For 6A Plug and 6A switch with 2-1.5

sq.mm Cu. Wire from nearby

switchboard /mcb db board

(e) in existing pipe erected flushed on

wall / ceiling complete Cat III

Same as Above for-[II] For 16A Plug and

16 amp switch with 2-2.5 sq.mm Cu.

7.2 Wire from mcb db board.(e) in existing Pt.

pipe erected flushed on wall / ceiling

complete Cat III

Point wiring for on board Looped Plug

with 6A Modular type switch & 5 pin

socket erected on PVC / Metallic /

Wooden box, single mounting base

frame covered with textured / metallic /

white front plate modules erected on /

in wall / ceiling with following type

accessories Cat III

Providing and erecting ISI mark Medium

class RIGID PVC PIPES of following size

complete to be erected on / in wall or

ceiling erected with necessary PVC

9.1 fittings & Junction boxes fixed with Mtr.

adhesive solution & Clamps with

following dia of pipes, in approved

manner as directed

9.2 Same as Above for- Mtr.

Providing and erecting Mains with

KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire

10.1 in following type of pipe to be erected Mtr.

concealed in / flushed on wall / ceiling

with 1.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green

colour for earth continuity of following

(A) with medium class Rigid PVC pipe

and accessories

(a) 2 wire 1.5 sq. mm

10.2 Same as Above for- Mtr.

(b) 2 wire 2.5 sq. mm

10.3 Same as Above for- Mtr.

(c) 3 wire 1.5 sq. mm

10.4 Same as Above for- Mtr.

(d) 3 wire 2.5 sq. mm

10.5 Same as Above for- Mtr.

(e) 4 wire 1.5 sq. mm

10.6 Same as Above for- Mtr.

(f) 4 wire 2.5 sq. mm

Providing and erecting Mains with

KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire

in following type of pipe to be erected in

/ on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated

stranded wire of green colour for earth

continuity of following size

(E)in existing pipe

(a) 2 wire 4 sq. mm

11.2 Same as Above for- Mtr.

(b) 2 wire 6 sq. mm

Providing and erecting Mains with ISI

marked, 1.5 KV grade electrolyte multi

stranded, annealed copper conductor

with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in

12.1 existing pipe of following size Mtr

(Specifically for control panel, relays,

power switchgears, motor starters &

control wiring) with required size of

copper lugs, nuts and bolts if required.

(d) One wire 4.00 sq. mm

12.2 Same as Above for- Mtr

(e) One wire 6.00 sq. mm

12.3 Same as Above for- Mtr

(f) One wire 10.00 sq. mm

12.4 Same as Above for- Mtr

(g) One wire 16.00 sq. mm

12.5 Same as Above for- Mtr

(h) One wire 25.00 sq. mm

12.6 Same as Above for- Mtr

(i) One wire 35.00 sq. mm

12.7 Same as Above for- Mtr

(j) One wire 50.00 sq. mm

Providing and erecting XLPE (IS:7098)(I)-

88 ISI armoured cable multistrand /

Solid Aluminium conductor for 1.1 KV to

13.0 be laid on wall with necessary clamps or Mtr

in existing trench / pipe of following size

(c) 4 core 10.00 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-

88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV to be

14.1 laid on wall with necessary clamps or in Mtr

existing trench / pipe of following size of

(A) 4 core 16.00 Sq. mm

14.2 Same as Above for- Mtr

(B) 4 core 25.00 Sq. mm

14.3 Same as Above for- Mtr

(C) 4 core 35.00 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-

88 ISI armoured cable multistrand

Copper conductor for 1.1 KV to be laid

15.1 on wall with necessary clamps or in Mtr.

existing trench / pipe at road crossing or

floor of following size of cables.(A) 3 1/2

core 25 Sq. mm (10 Sq. mm 1/2 core)

Same as Above for-

15.2 (B) 3 1/2 core 35 Sq. mm Mtr.

(16 Sq. mm 1/2 core)

SITC of 14.2 mm dia 3 mtr long Earth

electrode of High tensile steel electrode

with 250 micron copper bonding & 1 bag

of Carbon fill Based environment

friendly backfill tested as per IEC

62561-7 in NABL accredited Laboratory

and suitable stainless Steel double sided

clamp. Eco Friendly rust proof heavy

duty weather proof Polyethylene Earth

Pit Chamber with following dimensions:

254 mm dia (top), 330 mm dia (bottom)

& 260 mm (height).

Supplying and erecting LED indoor

fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB

with housing used as a heat sink shall

be made of thick sheet Steel conforming

to IS:513/CRCA/aluminium pressure

die cast powder coated and high U.V. &

corrosion resistance with diffuser

housed in aluminium casted body with

company mark / name

160V to 270V, Power Factor more than

Luminaire efficacy> 85 lumens/watt,

LED driver efficiency >85%

(fitting required LM-79 & LM-80

Certificates) (NOTE: Below description

have shown ranges of Wattage capacity

of LED fittings. The Engineer incharge

may select any wattage capacity between

the ranges shown.)

(A) Tube Light with integral driver (iii)

18-20 Watts, Surge - 2KV,IP-20,

conventional 4 feet Cat-lll

Supplying and erecting LED indoor

fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall

be made of thick sheet Steel conforming

to IS: 513/CRCA/aluminium pressure

die cast powder coated and high U.V. &

corrosion resistance with diffuser

housed in aluminium casted body with

company mark/name

160V to 270V, Power Factor more than

18.1 Luminaire efficacy> 85 lumens/watt, Ea.

LED driver efficiency > 85%

(fitting required LM-79 & LM-80

Certificates) (NOTE: Below description

have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge

may select any wattage capacity between

the ranges shown.)

(A) Square / Circular shaped Surface /

Recessed Mount Downlight with

provision for spring loaded mounting

clips complete.IP20

(i) 5-9 watts,Surge-2 KV Cat-lll

18.2 Same as Above for- Ea.

(ii) 11-15 watts, Surge-2 KV Cat-lll

18.3 Same as Above for- Ea.

(iii) 16-20 watts, Surge-2 KV Cat-lll

18.4 Same as Above for- Ea.

(iv) 22-24 watts, Surge-2 KV Cat-lll

Same as Above for-

(B) LED Panel Light with provision for

18.5 Plane front frame with translucent cover Ea.

fixed to housing complete. IP20

(iv) 18 to 20 watts, 8" x 8", Surge- 2 KV

18.6 Same as Above for- Ea.

(v) 24 watts, 12" x 12", Surge-2 KV

18.7 Same as Above for- Ea.

(vi) 36 watts, 24" x 24" mm, Surge- 2KV

Same as Above for-

18.8 (vii) from 45 to 48 watts, 24" x 24", Ea.

Surge-2 KV Cat-lll

Supplying and erecting LED street light

/ Flood light fittings with High power

White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free

High pressure die cast aluminum

housing with smooth finish powder

coated and heat sink extruded

aluminium with diffuser and

Polycarbonate optics/ lenses, with

toughened glass with company

mark/name engraved or embossed

to 270 V, Power Factor more than 0.95,

19.1 THD <10%, CCT 3000K to 5700K, E.a.

Uniformity ratio >0.45, Luminaire

efficiency > 100 lumens/watt. LED

driver efficiency >85%.(fittings required

LM-79 & LM-80 certificates) (NOTE:

Below description have shown ranges of

Wattage capacity of LED fittings. The

Engineer incharge may select any

wattage capacity between the ranges

shown.)(B) Flood Light (IP-65), Surge

protection -4KV integral and Light must

have 440VAC line supply with over-

voltage protection.(iv) Above 90W to

19.2 Same as Above for- Ea.

(vi) above 160 to 200 watts Cat.III

Providing and erecting Miniature circuit

breaker single pole 6A to 25A suitable to

operate on 240 V A.C. system and

having breaking capacity 10 KA to be

erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III

Providing & erecting 240 V MCB double

pole switch for motor & inductive load (C

Curve) having 10 KA breaking capacity

& confirms to IS : 8828 in existing box

having following capacity

(a) 6 to 32 Amp. Cat.III

21.2 Same as Above for- Ea.

(b) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four

Pole for Motor & Inductive Load (C

Curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box

having following capacity

(a) 6 to 32 Amp. Cat.III

22.2 Same as Above for- Ea.

(b) 40 Amp. Cat.III

22.3 Same as Above for- Ea.

(c) 63 Amp. Cat.III

Providing & erecting 415 V MCB three

Pole for Motor & Inductive Load (C

Curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box

having following capacity

(a) 6 to 32 Amp. Cat.III

23.2 Same as Above for- Ea.

(b) 40 Amp. Cat.III

23.3 Same as Above for- Ea.

(c) 63 Amp. Cat.III

Providing and erecting Sheet Steel

powder coated MCB distribution board -

flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN

rail, confirming to IS 8623-1&3 and

iec61439-1&3 without MCB to house

24.1 appropriate nos. of MCBs (The DBs Ea.

should be used of same company of

MCB to be used) suitable for

(A) single phase incoming and horizontal

single phase outgoing (b) sheet steel

double door (IP-43)

(i) Single phase 4way SS Double door

24.2 Same as Above for- Ea.

(ii) Single phase 6way SS Double door

24.3 Same as Above for- Ea.

(iii) Single phase 8 way SS Double door

24.4 Same as Above for- Ea.

(iv) Single phase 12 way SS double door

Same as Above for-

(B) three phase incoming and single

phase horizontal type outgoing Per

phase isolation type (PPI) (b) sheet steel

(i) Three phase 4 way SS Double door

24.6 Same as Above for- Ea.

(ii) Three phase 6 way SS Double door

24.7 Same as Above for- Ea.

(iii) Three phase 8 way SS Double door

24.8 Same as Above for- Ea.

(iv) Three phase 12 way SS Double door

Providing and erecting Approved make

ELCBs / RCCBs conforming to IS:12640

and having sensitivity of 30 mA and

Short Circuit withstand capacity of

KA and suitable for operation on single

25.1 phase 240 V, 50Hz. having Ea.

characteristic of quick action & tripping

with all advance feature & do not

incorporate any electronic component

for following Max. rating erected as

directed(i) 25 Amps. DP Cat. III

25.2 Same as Above for- Ea.

(ii) 40 Amps. DP Cat. III

25.3 Same as Above for- Ea.

(iii) 63 Amps. DP Cat. III

Providing and erecting Approved make

ELCBs / RCCBs conforming to IS:12640

and having sensitivity of 30 mA and

Short Circuit withstand capacity of

KA and suitable for operation on 3 phase

and neutral 415V, 50Hz. having

characteristic of quick action & tripping

with all advance feature & do not

incorporate any electronic component

for following Max. rating erected as

(i) 25 Amps. FP Cat III

Same as Above for-

(ii) 40 Amps. FP Cat III

26.3 Same as Above for- Ea.

(Iii) 63 Amps. FP Cat III

Same as Above for-

26.4 (iv) 100 Amps. FP (100 mA Sensitivity) Ea.

Providing and erecting busbar chamber

confirming to IS-375 fabricated from

G.M.S. sheet, dust & vermin proof

having hinged door with rubber gasket

and necessary busbar supports with

COPPER busbar having current density

not more than 1.6 Amp. / sq. mm (Rated

current / cross section area) duly

wrapped with colour insulation tape for

phase sequence, three phase & neutral

each suitable for following current

capacity with necessary painting

mounted on wall or pedestal frame of

required size with necessary

(A) 63A / 100A capacity

Providing and erecting busbar chamber

confirming to IS-375 fabricated from

G.M.S. sheet, dust & vermin proof

having hinged door with rubber gasket

and necessary busbar supports with

Aluminium busbar having current

density not more than 0.8 Amp. /

sq.mm (Rated current / cross section

area) duly wrapped with colour

insulation tape for phase sequence,

three phase & neutral each Suitable for

following current capacity with

necessary painting mounted on wall or

pedestal frame of required size with

necessary connections.

(A) Suitable for 63/ 100 Amp. Capacity

Supplying & erecting fan hook box of

mm M.S. round bar bounded to the RCC

bars up to 50 mm length each side and

29.0 pierced through a 16 Gauge M.S. box / Ea.

Heavy Duty PVC box complete erected

concealed in Ceiling with necessary

Supplying & erecting approved make low

noise decorative exhaust fan having size

30.0 200mm with 1350 RPM with square Ea.

frame ABS body with inbuilt lowers &

square frame. CAT-II

Supplying & erecting single phase

approved make industrial exhaust fan

suitable for medium duty ring mounted

31.0 low noise operation suitable for medium Ea.

duty having following dia size and

maximum speed in RPM

[A] 305 mm dia 900 RPM Cat- II

Supplying and erecting approved make

Bracket fan of 230 volt, A.C. 50 Cy/s.,

32.0 400/450 mm sweep complete erected on Ea.

wall or with lead Cores and connections

complete. Cat- II

Supplying and erecting approved make

pedestal fan A.C. 230V, 50 Cy/s,

mm sweep oscillating type and

adjustable height complete with guard

regulator & standard lead flexible wires

and plug top. Cat- II

Providing and erecting Approved make

Ceiling fan with double ball bearing ISI

mark with condenser A.C. 23OV, 50 c/s,

34.0 1200 mm sweep complete, canopy Ea.

erected on existing hook or clamp with

earthing. [Make shall be approved by

Engineer in charge]

Supplying and erecting 19/20 mm

nominal bore Medium Class M.S. Pipe

35.0 down rode erected duly painted for fan Mtr.

complete with proper insulation without

leakage and earthing.

Providing and erecting Approved make

Four pole moulded case circuit breaker

having breaking capacity ICU of 25 KA

at 415 V having normal current rating

up to 25 A to 100A with Fixed thermal &

magnetic release suitable to work on

A.C. supply 50 c/s with all internal

connections & complete erected in

existing 16 G.M.S. housing.ICU = 100 %

of ICU ONLY Cat-III

Approved make four pole moulded case

circuit breaker having breaking capacity

ICU of 35 kA at 415 V having normal

current rating up to 125 Amps with fixed

thermal & magnetic release suitable to

work on AC supply 50 Cys with all

internal connections & com

ICU = 100 % of ICU ONLY Cat-III

Providing and erecting Approved make

Four pole moulded case circuit breaker

having breaking capacity ICU of 35 KA

at 415 V having Normal current rating

200A with variable Thermal & magnetic

release suitable to work on A.C. supply

50 c/s with all internal connections &

complete erected in existing 16 G.M.S.

ICS=100% of ICU only Cat III

Providing and erecting Approved make

Four pole moulded case circuit breaker

having breaking capacity ICU of 35 KA

and above at 415 V having normal

current rating 250A with variable

thermal & magnetic release suitable to

work on A.C. supply 50 c/s with all

internal connections & complete erected

in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Disconnecting the cable connection and

Providing straight joint with PVC mould

using heat shrink / cast resin type

epoxy compound Insulating material

and making the joint complete using

40.1 necessary in line connectors, hardener, Ea.

earth continuity connection, spacers etc.

and reconnecting the same & ensure the

joint resistance within the limits as per

(A) up to 25 Sq mm Cable

40.2 Same as Above for- Ea.

(B) 35 to 95 Sq. mm cable.

40.3 Same as Above for- Ea.

(C) 120 to 300 Sq. mm cable.

Providng and erecting Approved make

single phase electronic energy meter

rating 5A/20A/40A based on ASIC

(Application Specific integral circuit)

digital technology with accuracy Class-I,

temper proof, free from effect of external

41.0 magnetic field with phase, earth, reverse Ea.

and impulse indications, 6 digit electro-

mechanical counter suitable to work on

120 V to 300V, 45-55 Hz. housed in

robust enclosure complete to be erected

as directed with 3 year replacement

guarantee. Cat-III

Providng and erecting Approved make

energy meter 3 phase 4 wire unbalanced

load rating, 10A to 60 Amp. based on

ASIC(Application specific Integral

Circuits) digital technology with

accuracy Class - 1, temperproof, free

42.0 from effect of external magnetic field Ea.

with 3 phase indication, earth & impulse

indication, 6 digit electro mechanical

impulse counter, suitable work on 120 V

to 300 V per phase 45-55 Hz housed in

robust enclosure with erection as

directed. Cat-III

Providing following type of Modular Type

Accessories mounted with PVC /

metallic / Wooden box, single mounting

base frame covered with textured /

43.1 metallic / white front plate, modules Ea.

erected with necessary connections as

per site situation directed by Engineer In

(1)One No. SP 6 Amp.Cat.III

43.2 Same as Above for- Ea.

(2) One No 5 pin plug Cat.III

Same as Above for-

43.3 (5) Electronic hum free four or more Ea.

steps EME fan regulator cat.III

43.4 Same as Above for- Ea.

(7) Blank Plate Single cat-III

43.5 Same as Above for- Ea.

(9) 16 Amp. SP one way switch Cat.III

43.6 Same as Above for- Ea.

(10) 6/16 Amp. Universal socket Cat.III

Providing & Erecting following

Shockproof tissino type accessories

erected on 3 mm thick PC

44.1 (Polycarbonate) sheet in PVC / Metal / Ea.

Wooden Box erected on wall / ceiling.

(1) One no Single pole 6 A Switch / Bell

44.2 Same as Above for-(2) One no 3/5 pin 6 Ea.

44.3 Same as Above for- Ea.

(3) One no Single pole 16 A Switch

44.4 Same as Above for- Ea.

(4) One no 6/16 A Universal Socket

44.5 Same as Above for- Ea.

(8) Bakelite lamp holder

Same as Above for-

44.6 (14) Electronic Hum free EME Socket Ea.

Type Steps Fan Regulator

Providing & erecting ISI marked 3 pin

45.1 plug top. Ea.

45.2 Same as Above for- Ea.

46.0 Providing and erecting Annealed bare Kg.

Copper wire 8 to 16 SWG.

47.0 Providing and erecting HOT deep Kg.

Galvanised iron strip wire 8 to 16 SWG.

Rewinding of Any fan by using supper

enamelled copper wire and over hauling

and putting in working order with

original speed with guarantee for one

year including credit of D.M. retained by

Replacing the bearing/ bushing of

Ceiling fan and putting the fan in

49.1 working order including credit of D.M. Ea.

retained by Agency.

49.2 Same as Above for- Ea.

Replacing condenser for ceiling fan/

Exhaust Fan / Pedestal Fan / Table Fan

/ Cabin Fan {Credit of D.M. retained by

Supplying KITKAT pattern porcelain cut-

51.1 out fuse with base of following current Ea.

capacity erected on existing block board.

51.2 Same as Above for- Ea.

51.3 Same as Above for- Ea.

51.4 Same as Above for- Ea.

51.5 Same as Above for- Ea.

51.6 Same as Above for- Ea.

To attend Electrical fault and restore

52.0 /continue power supply in normal Ea.

53.0 Rate for providing Electrician as an Ea.

when required (1 Electrician) 8Hrs Shift

Estimated Amount in Rs.

Final Amount(Including GST) in Rs.

I/We am/are willing to carry out work at ____________% above or

____________% Below the estimated cost mentioned above.

NOTE:- The Quoted Rate Shall be Inclusive of all taxes.

Signature of the Tenderer Addl. Chief Engineer

Name : (Electrical)

Company’s seal Date :