Demolition of Existing Structures and Reconstruction of High School on Plot bearing S.No. 4/5A, 4/6A, 4/7A, 4/6, 4/7(part), 4/17(part), 4/18(part) of Village Alorna at Hankhane, Pernem Goa.

Fire Fighting Work: Supply, Fabrication, Erection, Testing, and commissioning of the following sizes of G.I. ERW C class pipes (conforming to IS -1239), Erection Above Ground (including proper iron supports and anchor fasteners), and Laying Underground with all fittings (standard MS fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, Washer, tie bolt, supports, clamps, etc, with one coat of red oxide primer and one coat of synthetic enamel paint. 50mm

Supply, Fabrication, Erection, Testing, and commissioning of the following sizes of G.I. ERW C class pipes (conforming to IS -1239), Erection Above Ground (including proper iron supports and anchor fasteners), and Laying Underground with all fittings (standard MS fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, Washer, tie bolt, supports, clamps, etc, with one coat of red oxide primer and one coat of synthetic enamel paint. 80mm

Supply, Fabrication, Erection, Testing, and commissioning of the following sizes of G.I. ERW C class pipes (conforming to IS -1239), Erection Above Ground (including proper iron supports and anchor fasteners), and Laying Underground with all fittings (standard MS fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, Washer, tie bolt, supports, clamps, etc, with one coat of red oxide primer and one coat of synthetic enamel paint. 100mm

Supply, Installation, Testing, and Commissioning of the following size cast iron double flange Butterfly Valve with matching flange, nut bolts & gasket. 80mm

Supply, Installation, Testing, and Commissioning of the following size cast iron double flange Butterfly Valve with matching flange, nut bolts & gasket. 100mm

Supply, Installation, Testing, and Commissioning of the following size cast iron double flange Non-Return Valve with matching flange, nut bolts & gasket. 100 mm

Supplying and fixing priming tank HDPE 10000 liters capacity

Supplying and fixing priming tank HDPE 5000 litres capacity

Supply, Installation, Testing, and Commissioning of pressure gauge of 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc.

Supply, Installation, Testing, and Commissioning of pressure switch with 12/15 mm Ø isolation valve, G.I. nipple, elbow, etc.

Supply, Installation & Testing of First aid Hose reel conforming to IS 884 completed with 19 mm dia. bore reinforced braided rubber hose of 30 mtrs length fitted with 6.35mm dia. shut off Nozzle, 25 mm dia. ball valve, etc. The hose reel shall be manual 180 deg. swinging type with reel drum hose shall be provided with coupling.

Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). The colour of the Directional and Fire Safety signages shall be RED with Graphic symbol in White colour and the colour of the Emergency escape signages shall be Green with Graphic symbol in WHITE colour as per IS 9457:2005. ASSEMBLY POINT (Size- 600 x 600 mm).

Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). The colour of the Signages will be Blue with Graphic symbol in WHITE colour as per IS 9457:2005. Ramp (Size- 200 x 200 mm).

Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). The colour of the Signages will be Blue with Graphic symbol in WHITE colour as per IS 9457:2005. Lift (Size- 200 x 200 mm).

Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). The colour of the Directional and Fire Safety signages shall be RED with Graphic symbol in White colour and the colour of the Emergency escape signages shall be Green with Graphic symbol in WHITE colour as per IS 9457:2005. EXIT (Size- 100 x 300 mm).

Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). The colour of the Directional and Fire Safety signages shall be RED with Graphic symbol in White colour and the colour of the Emergency escape signages shall be Green with Graphic symbol in WHITE colour as per IS 9457:2005 [STAIRCASE IDENTIFICATION (Size- 100 x 300 mm)]

Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). The colour of the Directional and Fire Safety signages shall be RED with Graphic symbol in White colour and the colour of the Emergency escape signages shall be Green with Graphic symbol in WHITE colour as per IS 9457:2005. FIRE EXTINGUISHER (Size- 200 x 250 mm).

Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). The colour of the Directional and Fire Safety signages shall be RED with Graphic symbol in White colour and the colour of the Emergency escape signages shall be Green with Graphic symbol in WHITE colour as per IS 9457:2005 [HOSE REEL HOSE (Size- 200 x 250 mm)]

Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). The colour of the Directional and Fire Safety signages shall be RED with Graphic symbol in White colour and the colour of the Emergency escape signages shall be Green with Graphic symbol in WHITE colour as per IS 9457:2005. MCP (Size- 200 x 250 mm).

Supply, Installation, perfect aligning and proper leveling and testing, and Commissioning of centrifugal pump set, electrically driven complete with all accessories suitable for pumping water with 900 LPM and 44 m head coupled with 11.19 KW of electric motor AC 3 phase, 50Hz including supply and fixing the items, such as necessary connection from starter to the motor terminal using proper size of copper cable including, the connection of suction pipe from pump to foot valve, delivery pipe connected to the raising mains of the overhead reservoir by means of suitable joints painting the suction and delivery pipe with super enamel paint over a coat of primer as per standard code of colour including MS base plate complete complete all as specified and directed. (Main pump Hydrant))

Supply of 3 core armoured PVC/XLPE insulated PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) IS:7098(Part I) with latest amendments of following size.;3 Core 6 sq.mm

Supply of 4 core armoured PVC/XLPE insulated PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) IS:7098(Part I) with latest amendments of following size.;4 Core 10 sq.mm

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade complete as required.;(3) 3 x 6 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade complete as required.;(4) 4 x 10 Sq. mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface etc. complete as required

Supplying installation testing and commissioning of surface/ recess mounting vertical type 415 V TPN double door MCB DB of sheet steel dust protected duly phosphatised and powder painted inclusive of 200 A tinned copper busbar common neutral link earth bar din bar for mounting MCBs detachable gland knock out plate and with 100 A 10 KA MCCB as incomer interconnection between incomer MCCB and busbars of following ways (but without MCCB/MCBs as required);(d) 4 way with 100A MCCB as Incomer double door Cat B

Providing and fixing following rating and breaking capacity adjustible 4 pole MCCB inside the existing cubicle panel board including drilling holes in cubicle panel making connections etc as required;(a) 100 A Adjustable 35/40 KA CAT B

Supplying and laying 25 mm x 5 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe 20mm Class B with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid seperately).;(a) In soily strata

Extra for using salt and charcoal for GI or copper plate earth electrode as required( 96 Kgs of Charcoal and 5 Kgs of Salt)

Supply, Installation, Testing & Commissioning of Conventional Type Sounder with strobe light

Supply, installation, testing, and commissioning of conventional type Manual Call Point with back box.

Supply, Installation, Testing & Commissioning of 4 Zone Micro processer based Fire Alarm Control panel with battery charger, 48 hours battery back-up, and related accessories

Supply of 2 core armoured PVC/XLPE insulated PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) IS:7098(Part I) with latest amendments of following size.;2 Core 1.5 sq.mm

Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. Capacity, conforming to IS 2878 Complete with, necessary clamp made front 50mm x 6mm. M.S. flat with nut & bolts grouted in wall complete

Supplying and erecting ABC powder fire extinguisher as per IS: 13849 of 6 kg capacity with necessary clamp for erection on the wall.

Elevator Work: Lifts up to 5 floors, G+4 (Passenger Lift), 8 Nos. passenger capacity. Speed 0.6-1 m/sec (Refer Annexure-I)

Electrical Work: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch modular plates suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.;(c) Group C -- with Cat A Modular Accessories

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with 2 way modular switch modular plates suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.;(a) with Cat A Modular accessories

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required.;(a) 2 x 1.5 sq.mm + 1 x 1.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required.;(b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required.;(c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required.;(k) 4 x 10 sq.mm + 2 x 10 sq.mm earthwire (32mm Conduit)

Supplying and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch on board the modular surface/recessed PVC/GI modular box by suitably increasing its modular capacity modular plate and cover including connection painting etc. as required.;(a) Cat A

Supplying and fixing suitable size modular PVC box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required.

Supplying and fixing suitable size modular PVC box with modular plate and cover in front on surface or in recess including providing and fixing 4 nos 3 pin 5/6 A modular socket outlet and 4 nos 5/ 6 A modular switch connection painting etc. as required. The scope of work includes alternate arrangement if required as per site conditions to provide switches and sockets seperately above and below the table respectively. (For workstations);(a) Cat A

Supplying and fixing suitable size modular PVC box with modular plate and cover in front on surface or in recess including providing and fixing 1 no 6 pin 15/16 A modular socket outlet and 1 nos 15/ 16 A modular switch connection painting etc. as required. ( For workstations);(a) Cat A

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required;(a) Cat A

Supplying and fixing modular blanking plate on the existing modular plate switch box excluding modular plate etc. as required;(a) Cat A

Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required;(a) 1 or 2 Module ( 75 mm x 75 mm) Cat A

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing required number of modular switches connection painting etc. as required. ( For group controlled points);(a) Cat A

Supplying and fixing following way TPN sheet steel double door Verticle type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)interconnection between incomer MCB and busbars of following ways (but without MCBs as required);(a) 4 way (8+12) double door Vertical type Cat A

Supplying and fixing following way TPN sheet steel double door Verticle type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)interconnection between incomer MCB and busbars of following ways (but without MCBs as required);(b) 8 way (8+24) double door Vertical type Cat A

Supplying and fixing 6 A to 32 A C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.;(a) SP Cat A

Supplying and fixing 63 A C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.;(d) TP Cat A

Supplying and fixing 63 A C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.;(e) TPN Cat A

Supply of 4 core armoured PVC/XLPE insulated PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) IS:7098(Part I) with latest amendments of following size.;4 Core 25 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) IS:7098(Part I) with latest amendments of following size.;3 1/2 Core 50 sq.mm

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade complete as required.;(6) 4 x 25 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade complete as required.;(3) 3 1/2 x 50 Sq. mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing masonry open duct etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm in the existing masonry open duct etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Inchargesand cushioning with screened sand bed of 20mm thick protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.;(a) In soily strata

Supplying and drawing of Cat - 6 UTP 4 pair annealed tinned copper conductor PVC insulated PVC sheathed unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection etc. complete as required;(a) Cat 6

Supplying installation and testing of suitable size modular GI box modular plate and cover complete with RJ-45 connector(modular LAN socket TX1000/ CAT6) including concealed metal box/surface GI/PVC Box modular plate punching identifying complete as required.;CAT A

Supplying and drawing/fixing indoor type 0.5 sq.mm FR PVC insulated copper conductor unarmoured telephone cable ITD/DOT approved with GI saddles on wal or in the existing surface/recesed steel/PVC conduit having folowing pair(s) complete as required.;(a) 2 Pair

Supplying installation and testing of suitable size modular GI box modular plate and cover complete with RJ-11 connector(modular telephone socket) including concealed metal box/surface GI/PVC Box modular plate punching identifying complete as required.;CAT A

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required.;(a) 20 mm

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required.;(c) 32 mm

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark of approved brands including accessories and providing masonry enclosure with CI/RCC cover having locking /Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size not less than 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size not less than 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement(plumbing will be paid seperately).;(b) In rocky strata

Extra for using salt and charcoal for pipe earth electrode as required( 65 Kgs of Charcoal and 5 Kgs of Salt).

Providing and laying earth connection from earth lectrode with4 mm dia copper wire in 15 mm dia GI pipe from earth electrode as required

Providing and fixing 4 mm dia copper wire on surface or in recess for loop arthing along with existing surface/ recessed conduit/ submain wiring/ cable as required

Transportation, Supply, installation, testing and commissioning of indoor type feeder panel fabricated in 14/16 SWG CRCA sheet, flush front. compartmentalised, dust and vermin proof, dully powder coated or painted floor mounted at a suitable height of 0.25 mtrs from ground and based on an angle frame of size cade 35mmx35mmx35mm size, cable entry from top /bottom for out going cables suitable for operation on 440V, 3 phase, 4 wire, 50 Hz supply complete 8 with interconnections with proper sizes of wires, copper wiring, lugs, earthing bus etc. The panel board shall comprise of the following INCOMING a) Sealable Metering compartment with 63 Amps, TP MCB & direct type energy meter -1 set b) RYB indicators - 1 set. c) Digital Voltmeter, Ammeter-1 set d) 3 phase 100 Amps aluminium busbar OUTGOING 1. 63 amps10KA TP MCCB - 4 Nos, 2. 32 amps tp mcb -2 nos, 3. 16 amps tp mcb -4 nos (Make: L&T/ schneider etc)

Civil Work: Providing and fixing anodised aluminium shutters in accordance with the specification annexed herewith including transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: windows with three sliding shutters using 18 mm series shutters section.;Plain glass

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: windows with two sliding shutters using 18 mm series shutters section.Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section b) Plain glass

Providing and fixing anodised aluminium shutters in accordance with the specification annexed herewith including transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Openable windows and ventilators using 18 mm series shutters section.;Plain glass

Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws.;Ornamental grill

Providing and fixing 38 mm thick panelled glazed or panelled and glazed shutters for doors windows and clerestory window including anodized aluminium butt hinges with necessary screws:;Second class Indian teak wood

Single Colour Foam Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood moisture less than 17% wood styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) . The core of shutter will be filled as specified (Expanded Polystyrene Foam / Polyurethane Foam (EPS/PU) Foam). The shutter to be of single colour & water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory. Accessories: i) S. S. Hinges 4” - 3 Nos ii) S. S. Latch - 1 No iii) Tower Bolt 5” - 2 Nos iv) Handle 5” - 2 Nos Note: For 35 & 40mm thickness shutters only frames of 5 x 2 ½ Cross section frames to be used.;Shutter Thickness;35mm

Wood Finish Wood Core FRP (Fiber Reinforced Polymer) Door Shutter. Manufacture Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood moisture less than 17% wooden styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) and printed matt having wooden textures used along with UV Resistant resin to give the clear texture on the door. The core of shutter will be filled with MR 2nd grade Block Board. The Shutter to be water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory. Accessories: i) S. S. Hinges 4” - 3 Nos ii) S. S. Latch - 1 No iii) Tower Bolt 5” - 2 Nos iv) Handle 5” - 2 Nos;Shutter Thickness;35mm

Providing woodwork in frames of doors windows clerestory windows trusses & other frames wrought framed and fixed in positon.;Second class Indian teak wood

FRP (Fiber Reinforced Polymer) Frames Manufacture Supply and Installation (with anchor fastener) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) Frame of cross section as per options below with right angle joint and FRP (Fiber Reinforced Polymer) laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber (matt) and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps). The core of frame would be filled with seasoned wood as infill material. The slot of frame for door resting will be of suitable width so as to take specified thickness door.. The frame will be water proof as well as mild acid/ alkali resistant manufactured in an ISO 9001- 2015 certified company.;Specified Cross Section;4” x 2 ½ “

FRP (Fiber Reinforced Polymer) Frames with Wood Finish Manufacture Supply and Installation (with anchor fastener) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) Frame of cross section as per options below with right angle joint and FRP (Fiber Reinforced Polymer) laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber (matt) and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps). The core of frame would be filled with seasoned wood as infill material. The slot of frame for door resting will be of suitable width so as to take specified thickness door. The frame will be water proof as well as mild acid/ alkali resistant manufactured in an ISO 9001- 2015 certified company.;Specified Cross Section;4” x 2 ½

Providing flat iron hold fast 40 cm including fixing to frame with 10 mm dia bolts nuts and wooden plugs and embeded in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 stone aggregate 20 mm nominal size.;40 x 3 mm flat iron hold fast 15 cm long

Providing and fixing bright finished brass sliding door bolts with nuts and screws etc complete;250 x 16 mm

Providing and fixing bright finished brass tower bolts (barrel type) with screws etc. complete;250 x 10 mm

Providing and fixing bright finished brass door latch with necessary screws etc complete;250 x 16 x 5 mm

Providing and fixing bright finished brass handles with necessary screws etc complete;125 mm

Providing & fixing bright finished brass 100 mm. rim latch & lock & a pair of knob with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing 150 mm. bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete.

Providing and fixing brass hydraulic door closer of make Everest universal 68 or equivalent with necessary screws and fittings complete.

Half brick masonry in cement mortar 1:4 (1 cement :4 coarse sand) with bricks of class designation 40 kg/ sq. cm upto floor five level .;In foundation and plinth.;Upto floor V level.

Laterite masonry in neatly dressed stones for 23cm thick masonary walls in cm.1:4(1 cement :4 coarse sand in foundation upto plinth level) Extra for laterite Masonry in all sizes in superstructure from floor I level upto floor V level

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Extra for plastering exterior walls of height more than 10m from ground level for every additional height of 3m or part thereof.

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade.

Melamine polishing on wood work (one or more coat);Matt

12mm cement plaster 1:4 (1 cement : 4 fine sand)

6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand)

Finishing fine with neeru over plaster

Distempering two or more coats with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Providing anti – termite treatment to buildings conforming to I.S.S. 6113 part II 1971 (revised) including adopting precautions for health hazards and safety measures as required therein with the cost of all materials chemicals plants equipments required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. (The payment will be made on plinth of the building.;Pre-construction

Providing and fixing vitrified matt finished (600x600) and 10mm thick tiles in floor treads of steps landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of lime mortar 1:1:1 (1 lime putty : 1 surkhi : 1 coarse sand)

Floor polishing on masonry or concrete floors with superior quality wax polish of approved brand and manufacture.

Providing and fixing vitrified antiskid tiles (320x320) and 10mm thick tiles in floor treads of steps landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622 of approved make in all colours & shade in skirting riser of steps and dados jointing with grey cement slurry @3.3 kg per sqm including pointing/grouting in white cement mixed with pigment of matching shade complete.;600 x 600 mm - Dark Shades

Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps skirting dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete;Jet black

Rounding of edges of marble slab to semi circular slope

Providing and fixing 18 mm thick gang saw cut mirror polished premoulded and prepolished machine cut for kitchen platforms vanity counters window sills facias and similar locations of required size approved shade colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement mixed with matching pigment epoxy touch ups including rubbing curing moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade area of slab over 0.50 sqm;Jet Black

Providing 20mm thick marble slab to urinal partitions with cement complete

Providing 25 mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar complete as directed by the engineer-in-charge

Proving and fixing white vitreous china water closet squatting pan (Indian type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 10 litres high level P.V.C. flushing cister (of approved make) with fittings rack bolts 32 mm diameter P.V.C telescopic flush pipe with fit tings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon pull complete cutting and making good the walls and floors where required.;Orissa pattern W.C. pan

Providing and fixing white vitereous china pedestal type (Europen type) water closet with seat as lid whth C.I. brass hinges and rubber fitings 15 lts white vitreous china low level flushing cistern with fittings as brackets 40 mm white precelain 3enameled flush bad 25 mm overflow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required.;W.C. pan with white plastic seat and lid

Providing and fixing P.V.C. connection pipe with brass unions 15 mm nominal bore:;37.5 cm (15”) length .

Providing and fixing NICKEL chrome plated copper alloy Fancy Pillar Cock rocket type Jaquar make or equivalent. Confirming to IS 8931;1993;15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy concealed stop cock with slinding flance 15 mm Jaquar make or equivalent. Confirming to IS 8931;1993;15mm nominal bore

Providing and fixing nahani trap of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete without door :;110 mm dia

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleats with C. P. brass screws and washers.

Providing & fixing c.p. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C. P. brass screws;600 x 20 mm size

Providing and fixing toilet paper holder :;C.P. brass

Providing & fixing liquid soap container with C. P. brass lid and brackets fixed to wooden cleats with C. P. brass screws;Glass container

Providing & fixing 600 x 120 mm glass shelf with C. P. brass brackets and guard rail complete fixed to wooden cleats with C. P. brass screws.

Providing & fixing soap dish chromium plated with brackets fixed to wooden cleats with CP brass screw

Providing and fixing NICKEL chrome plated copper alloy Fancy Two Way Bib Cock with single knob and wall flange conforming to IS 8931:1993 15mm nominal bore.

Providing and fixing Hand Shower (Health Faucet) with 8mm dia ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock Short Body Jaquar make or equivalent. Confirming to IS 8931;1993;15mm nominal bore

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform vanity counter and similar location in marble/Granite/Cuddapah stone work including necessary holes for pillar taps etc. including moulding rubbing and polishing of cut edges etc. complete.

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with grade M 25 mix design with coarse sand and graded granitic or basaltic stone aggregate as per mix design requirements foundation concrete M 25 mix design with coarse sand graded granitic or basaltic stone aggregate as per mix design requirements inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design.;Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg).

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with grade M 25 mix design with coarse sand and graded granitic or basaltic stone aggregate as per mix design requirements foundation concrete M 25 mix design with coarse sand graded granitic or basaltic stone aggregate as per mix design requirements inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design.;Inside size 90 x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455 x610mm internal dimensions total weight of cover ad frame to be not less than 38 kg. (weight of cover 23 kg. )

Providing and fixing rigid PVC S.W.R. (soil waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:;110 mm dia

Providing and fixing rigid PVC S.W.R. (soil waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:;75 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating.;110 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating.;75 mm dia

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door :;100 mm dia

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door :;75 mm dia

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete with door :;110 mm dia

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete with door :;75 mm dia

Providing and fixing U.P.V.C. pipe clips (approved make ) for S.W.R. pipes :;110 mm dia

Providing and fixing U.P.V.C. pipe clips (approved make ) for S.W.R. pipes :;75 mm dia

Providing and fixing R.P.V.C. vent cowl:;110 mm dia

Providing and fixing R.P.V.C. vent cowl:;75 mm dia

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern 32 mm diameter M.I. or C.P. brass trap and union complete including cutting and making good the walls where required.;Flat back wash basin size 630x 450mm with a single 15 mm C.P. brass pillar taps.

Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing NICKEL chrome plated copper alloy Fancy waste coupling 32 mm with 190 mm long connection pipe wall flance Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing one piece construction white vitreous china squatting plate urinal with an integral longitudinal flushing pipe 100mm dia half round channel pvc. Automatic flushing cistern with fittings R.S. or C.I. brackets standard size G.I. flush pipe for back and front flush with stadard spreader fittings G.I. clamps white vitreous china tiling 1200 mm high to front and side walls with white vitreous corners and angles set in neat cement standard urinal C.I. trap 65 mm diameter with vent arm & outlet grating & coupling in c.p. brass complete including painting the cistern & fittings cutting and making good the walls and floors where required.;Single plate with 5 litres pvc. automatic flushing cistern.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc.;25 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc.;32 mm dia nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement trenching refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe);25 mm nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement trenching refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe);32 mm nominal outer dia pipes.

Providing and fixing ASTM UPVC pipe conforming to ASTM 2467 with ISO 14001 including all UPVC plain & brass threaded fittings including jointing of pipes & fittings with one step UPVC solvent cement trenching refilling & testing of joints complete as per direction of Engineer. External work.;SCH-40(blue)/(white);25mm outer dia.

Providing and fixing ASTM UPVC pipe conforming to ASTM 2467 with ISO 14001 including all UPVC plain & brass threaded fittings including jointing of pipes & fittings with one step UPVC solvent cement trenching refilling & testing of joints complete as per direction of Engineer. External work.;SCH-40(blue)/(white);32mm outer dia.

Providing and fixing ASTM UPVC pipe conforming to ASTM 2467 with ISO 14001 including all UPVC plain & brass threaded fittings including jointing of pipes & fittings with one step UPVC solvent cement trenching refilling & testing of joints complete as per direction of Engineer. External work.;SCH-40(blue)/(white);40mm outer dia.

Providing and fixing brass bib cock (heavy) of approved quality :;20 mm nominal bore

Providing and fixing brass stop cock (heavy) of approved quality :;20 mm nominal bore

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality :;20 mm nominal bore

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality :;32 mm nominal bore

Providing and fixing ball valve (brass) of approved quality :;High or low pressure with plastic floats:;25mm nominal bore

Providing and fixing non-return valve of approved quality :;25 mm nominal bore

Providing and fixing non-return valve of approved quality :;32 mm nominal bore

Providing and fixing normal gauge polythene pipes of approved quality complete with special flange compression type fitting (of approved make) including trenching ad refilling etc (external work) (high density):;50 mm nominal bore

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996.;1000 lit. capacity

Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with c.i. grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design :;150 x 100 mm size –P or S type

Providing and laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40 mm nominal size) alround S.W. pipes including bed concrete 15 cm thick as per standard design :;150 mm diameter.

Providing water proofing treatment over the new R.C.C. roofs terrace toilet by spreading cement slurry over the R.C.C. slab and laying of 10cms. Average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered with damp proof of Hindustan water proofing co. Or equivalent jointless water proofing plaster of mix 1:3 ( 1 cement : 3 find sand) finished smooth with wooden trowel with false marking of 30 cms square. The vertical surface of the adjoining walls are to be treated upto a height of 30cms including rounding of junction (the rate includes for complete items including labour and materials and including cost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb cracks etc. in the R.C.C. slabs). NOTE: cement consumption 25 kg/sq.m.

An elastomeric cementitious waterproof coating for concrete and masonry.;Providing and applying on a well prepared vertical surface Masterseal 550EL of BASF make or equivalent elastomeric flexible two component polymers modified cementitious composite system that requires no addition of water at the site. The product shall be applied in minimum two coats to achieve total DFT of 1mm. The material shall be mixed and applied fully in accordance with the manufacturer's instructions. The product shall exhibit at least 40% elongation at ambient & 30% elongation in under water condition with tensile strength greater then 20 Kg/cm2. The product shall resist 1.5 bars pressure when tested as per DIN 1048 at 2mm DFT. When applied at 2mm DFT elastomeric coating shall be able to bridge crack up to 0.5mm width. All scaffolding ladders supporting materials etc. complete. Rates shall be inclusive of all labour materials tools and plant etc. complete.

Jaisalmer stone flooring with 18mm thick polished Jaisalmer stone over 20mm (average) thick base of CM 1:4 (1 cement : 4 Coarse sand) with joints finished flush

Providing and laying in position ready mixed concrete (RMC) with usage of Ordinary Portland Cement manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continuous agitated mixer manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from the transit mixer to the site of laying excluding the cost of centering shuttering finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete improve workability without imparing strength and durability as per the directions of the engineer-in-charge. All works upto floor V level;M-30grade of concrete

Add for providing richer or leaner mixes respectively at all floor levels;Providing M-30 grade concrete by using 420kgs of cement per cu.m. of concrete instead of M-25 grade of B.M.C.

Providing and laying in position machine batched concrete (BMC) machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to the site of laying but excluding the cost of centering shuttering finishing and reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate retard setting of concrete improve workability without impairing the strength and durability as per the direction of the Engineer-in-charge. M25 grade of reinforced cement conrete by using 410kg of cement per cu.m. of concrete. All works upto floor V level.

Providing TMT steel reinforcement bars of (SAIL TATA. VIZAG JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m.;All kinds of soil

Extra for additional depth of 1.5 m or part thereof in:;All types of soil

Refilling the pipeline/foundation trenches plinth sides foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering shuttering and finishing in:;All works upto plinth level

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Neat Cement punning

Providing and fixing double “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete without door :;110 mm dia

Providing and fixing double “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete without door :;75 mm dia

Centering and shuttering including struttings propping etc. and removal of formwork for :;Foundations footings bases for columns and mass concrete.

Supplying and filling in plinth under floors trenches including watering ramming consolidating dressing complete.;Moorum

Making connection of drain or sewer line with existing manholes including braking into and making good the walls floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete:;For pipe 100 to 150 mm dia

Providing & laying damp proof course 50 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone agg. 20 mm nominal size).

Applying a coat of hot bitumen (maxphalt 80/100 or equivalent) using 1.5 kg/sq.m. on damp proof course after cleaning the surface with brushes and finally with a piece of cloth light soaked in bitumen.

Providing and fixing in position S.S. hand rail in main stair case and landing as per approved design shown in the drawing including bending handrail pipe to proper shape in curves with specials etc. complete.

Centering & shuttering including Strutting Propping & removal of forms for :;Columns Piers Pillars Aburments Posts and struts (square rectangle polygon in plan)

Centering & shuttering including Strutting Propping & removal of forms for :;Foundations Footings Bases for columns

Centering & shuttering including Strutting Propping & removal of forms for :;Vertical surfaces such as retaing walls return walls Partitions walls (any thickness) including attached Pilasters Buttresses Plinth and string courses Fillets and the like

Centering & shuttering including Strutting Propping & removal of forms for :;Staircases (except spiral staircases) excluding landing

Centering & shuttering including Strutting Propping & removal of forms for :;Suspended floors roofs landings shelves & their supports

Centering & shuttering including Strutting Propping & removal of forms for :;Sides and Soffits of beams Beam Haunchings Cantilever Girders Bressumers and Lintels plinth beams not exceeding 1m in depth

Centering & shuttering including Strutting Propping & removal of forms for sloping or battering surface (slabs beams louvers etc) including folded plates;Where inclination to the horizontal does not exceed 30° requiring shuttering on the underside only

Extra to be added for additional height in centering shuttering where ever required with adequate bracing propping etc. including cost of de- shuttering and de-centering at all levels over a height of 3.5m for every additional height of 1m or part thereof. (Plan area to be measured) Suspended floors roofs landings beams and balconies (plan area to be measured)

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins rafters trusses flashings etc. complete as per the directions of the Engineer in charge.

Add for providing & fixing Flashings -[Corners Ridges valleys gable end & Trims] (Girth upto 610mm) including all the accessories complete as per the directions of the Engineer in charge.

Steel work in built up tubular (round square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of (SAIL TATA. VIZAG JSW APOLLO Steel Ltd.) make (Min Yeild Stress 310 Mpa)) trusses etc. including cutting hoisting fixing in position and applying a priming coat of approved steel primer including welding and bolted with special shaped washers etc. complete.

Precast plain Cement Tacktiles 32mm thk of required shade in floors treads of steps and landing laid on 25mm bed of cement mortar 1:4(1cement:4coarse sand) jointed with neat cement slurry with pigment to match the shade of tiles including rubbing and polishing complete.

Demolition of load bearing Structure including demolition of Laterite/ Brickmasonary, dismantling of doors/ windows, flooring, roofing, steelwork, etc. Also providing barracading green net to prevent dust pollution, etc. including labour, loading, unloading, transportation of debris and material, etc complete as instructed by the Engineer in charge.

Demolition of R.C.C Structure including demolition of Laterite/ Brickmasonary, dismantling of doors/ windows, flooring, roofing, steelwork, etc. Also providing barracading green net to prevent dust pollution, etc. including labour, loading, unloading, transportation of debris and material, etc complete as instructed by the Engineer in charge.

Dismantling G.I. sheets roofing including ridges hips valleys and gutters etc. and stacking the material within 50 meters lead.

Dismantling steelwork in built up sections in angles tees flats and channels including all gusset plates bolts nuts cutting dismembering and staking within 50 mts. lead

Demolishing R.C.C. work including stacking of steel bars & disposal of unserviceable within 50 mts. lead.

Providing Grooves to granite

Providing and fixing 50 mm thick panelled glazed or panelled and glazed shutters for doors windows and clerestory window including anodized aluminium butt hinges with necessary screws:;First class Indian teak wood

providing and fixing vertical box member 10x40 made of ACP/PVC/AL

laterite Grit stucco finish/mural

Providing and fixing 15mm thick densified tengular edged eco friendly light weight Calcium Silicate false ceiling tiles (like Aerolite Brand or Equivalent) of approved texture Spintone/ Cosmos/ Fine Fissured or equivalent of size 595mm x 595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanizing @ 120 grams per square metre. including both side) consisting of main "T" runner suitably spaced at joints to get required length and of size 24x38mm made from 0.33mm thick (minium) sheet spaced 1200mm center to center and cross "T" of size 24x28mm made of 0.33mm thick (Minimum) sheet to be inter locked at middle of the 1200x600mm panel to from grid of size on a Perimeter wall angle precoated steel of size 600x600mm resting on periphery walls/ partitions (24x24x300mm) made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm and laying 15mm thick densified edges calcium silicate ceiling tiles of approved texture light fittings fixture smoke detectors etc. wherever required. Main "T" runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6mm fixed to celing using with 12.5mm dia and 50mm long dash fastners level clips of size 85x30x0.8mm spaced at 1200mm center to center along main "T" bottom exposed with 24mm of T-section shall be pre-painted with polyester baked paint for all heights as per specifications drawings etc. complete. (As Directed by Engineer in Charge) Note: Only Calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having are less than 0.30 sqm. The Calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection>85% non-combustible as per B.S.476 part IV, 100% humidity resistance and also having thermal conductivity 0.043 w/m 0 KC. Hospitals, Offices and Commercial Buildings, Auditoriums and Cinema Hall, Educational Institutions, R&D Centers, Studios, Laboratories, Library, Canteen.

Transportation and carriages of material by tipper truck including loading, unloading and stacking (A) Lime, building rubbish, manure sludge, moorum excavated rock. VII) 15kms

curtain wall with few top hung openable panels

Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section

Extra for placing polythene tank on roof of floor three (2nd floor roof);1000 lit. capacity

Salvage value of Mangalore tiles

Salvage value of matti wood

Centering & shuttering including Strutting Propping & removal of forms for sloping or battering surface (slabs beams louvers etc) including folded plates;Where inclination to the horizontal exceeds 30° requiring shuttering on the underside & upperside if required (Only area of underside shall be measured for payment)

RHS and SHS(SAIL, TATA, VIZAG, JSW Steel Ltd.)

0.75% consultancy charges on Civil Works (Rs.43321791.15)