BALANCE WORK for UPGRADATION OF SUJANPUR TO SARNA ALONG UBDC UNDER PMGSY- III BATCH-2 Block Sujanpur Distt Pathankot LENGTH 8.84 KM

Clearing and Grubbing Road Land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.

Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.

Construction of embankment with approved material deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification clause 301.5

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 mtr. Transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with lead upto 05 kms as per Technical Specification clause 301.5

Loosing, Levelling and compacting original Ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150mm, complete as per Technical specification clause 301.4

Providing and laying of Brick on end edging 6.83cm wide, 11.11cm long and 22.86cm high half brick deep including excavation, refilling and disposal of surplus earth up to 50mtr complete as per Technical specifications

Construction of granular sub base by providing well graded material, spreading in uniform layers on prepared surface, mixing by mix in place method at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical specification clause 401

Water Bound Macadam (Grading - II) - Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening ype-A/ binding materials to fill-up the interstices of coarse aggregate, watering and compacting to therequired density grading 2 as per MoRD Specification Clause 405.

Water Bound Macadam (Grading - III) -Providing, laying, spreading and compacting stone aggregates wbm GR-II) of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening type-B to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per MoRD Specification Clause 405.

Primer Coat - Providing and applying primer coat with Bitumen Emulsion (Slow Setting-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate 0.85 kg/sqm using mechanical means as per MoRD specification clause 502

Tack Coat - Providing and applying tack coat with Bitumen VG-10 using tar boiler / pressure distributor at the rate of 0.275 kg. per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per MoRD specification clause 503

Bituminous macadam -Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous inder VG-10 @ 3.4% transported to site upto a lead of 1000 m laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per Technical Specification Clause 504.

20mm Thick Open Graded Premix Carpet - Providing, laying and rolling of open graded premix carpet of 20mm thickness composed of 13.2mm to 5.6mm aggregates using Bitumen VG-10 to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, transported to site, laying and rolling with a three wheel 80-100 KN static roller capacity, finished to required level and grades to be followed by seal coat of Type ‘B as per MoRD specification clause 508.

Seal Coat - Providing and laying seal coat using Bitumen VG-10 for sealing the voids in bituminous surface laid to the specified levels, grade and cross fall using Type ‘B’ as per MoRD specification clause 510.

Providing Plain Cement Concrete 1:3:6 in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Stone Masonary work (1:4) in cement mortar in foundation and plinth complete excluding pointing and plastering as per drawing and technical specifications Clauses 702, 704, 1202 & 1203

Providing Cement Concrete (Plain / Reinforced) P.C.C. grade M 20 in Sub Structure complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Raised Pointing with cement mortar (1:2) on Stone wall in substructure as per CSR 15.64

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501.

White washing two coats on parapet walls and tree trunks including preparation of surface by cleaning scraping etc. as per technical specifications Clause 1915

Providing and laying reinforced cement concrete R.C.C M 25 in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5

Supplying, fitting and placing Fe500 bar reinforcement in Sub Structure complete as per drawings and technical specifications Clauses 1000 and 1202

Providing and fixing in position 20 mm thick premoulded joint filler in expansion joint for fixed ends of simply supported spans, covered with sealant complete as per drawing and technical specifications

Nicking cement concrete surface (over 28 days old including preparation and laying slurry (Based on CSR 10.31 (using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501)

Providing and Laying plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M60 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501.

Reinforced Cement Concrete M15 grade 200 metre stone (precast) stone of standard design as per IRC : & fixing in position including painting and printing, etc. as per drawing and MoRD Specification Clause 1703

Road marking with hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 0.25kg per sqm area as per IRC:35 1997 complete as per technical clause 803 of MORT&H specifications.

Supplying and fixing of single mould twin shank reflective road studs made out of poly carbonate/ABS moulded body and reflective panels with micro prismatic lens or Glass Beeds capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values shall be as given in the detailed specifications and the product shall conform to ASTM D4280. The raised pavementmarker shall also meet all the testing conditions of ASTM D4280 and fixed to the road surface using the adhesive. Two cylindrical Polymer Shanks of not less than 20 mm diameter and not less than 30 mm length shall be molded in the RPM body.The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280. The marker shall withstand flexural strength of 909 kgf force in accordance with ASTM D4280. Marker lenses shall be moulded of Polycarbonate or methyl methecrylate conforming to ASTM D788. The supplier shall provide a 2 years warranty for satisfactory field performance as per clause 804.7.3 of MO RT&H 5th revision specifications.

Supplying and fixing of Logo Board of PMGSY double Sided (Logo board at starting point & Intermediate distance) with Vertical Post MS Square Tube 80x80x4.80mm,Defination & Diamond Plate of ACP Sheet 3mm thick back side angle iron 25x25x3mm with Retro Reflective Tape type IV including cutting, lettering, Fixing comp. in all respects.

Providing and fixing of Retro-reflective Cautionary, Mandatory and Informatory Sign Boards as per IRC : 67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over Aluminium sheeting supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450mm x 600 mm, 600mm below ground level as per drawings and MoRD Specification Clause 801600mm equilateral triangle

Routine Maintenance for Five Year after completion of construction work as per periodicity of Routine Maintenance mentioned in the contract data.

For 1st year

For 2nd year

For 3rd year

For 4th year

For 5th year

Please Enable Macros to View BoQ information