Mtc. of non-residential building for office of the Executive Engineer, PWD(RnB), Ambassa Division in/c Ambassa and Jawharnagar Sub-Division during the year 2025-26/ SH- Finishing, providing interior decoration and Electrical re-wiring.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 11.32.3 12.5 mm thick tapered edge gypsum moisture resistant board.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board including\ providing and fixing of frame work made of special section power pressed/ role form G.I. sheet with zinc coating of grade 175 consisting of floor and ceilling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick fixed to the floor and ceilling at the spacing of 610 mm centre to centre with dash fastener of 12.50 mm dia-mater, 40 mm length and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceilling channel and placed at a spacing of 610 mm centre to centreb by 6 mm dia bolts and nuts at both ends of partition fixed flush to wall with rawl plugs at spacing 450 mm centre to centre and fixing of boards to either side of frame work by 25 mm drive all screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre, including jointing and finishing to a flush finish with recommended joiunting compound , jointing tape, joint finisher and two coats of primer siutable for boards asper manufacture's specification and direction of the Engineer-In-Charge all complete.. 8.103.1: 67mm overall thickness partition with 8.5 mm thick double skin Glass reinforced Gypsum (GRG) board conforming to IS: 2095: part III

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete

Providing & fixing in position high density fiber laminated wooden flooring with planks of sizes 8mm thick, 1202mm length (minimum) and 192 mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) conforming to EN 13329 standard issued by Manufacturer. The flooring shall be fixed with tongue and groove interlocking system, with underlayment of 4mm thick expanded poly ethylene foam sheets having density 40kg/m3, over prepared surface with necessary T-profile planks of size 2286mm x 45mm x 15 mm and door reducer of size 2286mm x 45mm x 12 mm, wherever required. The wood planks shall have minimum density of 850 Kg/cum with Eco friendly UV coating, etc. all complete as per direction of Engineer-incharge.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : 12.35.1:- New work ( two or more coats) over and including water thinnable priming coat with cement primer.

16.1.1:- For fixed portion of approved quality:- 16.1.1.1:-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

16.1.2:- For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- 16.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board grade-I, type II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P. brass / stainless steel screws all complete as per architectural drawing and the direction of Engineer-in-charge :- 16.2.2:-Prelaminated particle board of approved quality with decorative lamination on both side.

Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- 16.3.1:-With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm )

10.01 Short Point :-

10.02 Medium Point :-

10.03 Long Point :-

Providing and fixing of 3 pin 6/10 amps plug point with modular type 6/10 amps switch and socket including connection with 2x1.5 sq. mm PVC insulated Copper conductor cable (FR) on surface modular switch board, earthing the 3rd pin etc. as required:- (As per TSR 2021, Sl- 203)

Providing and fixing of 3/6 pin 16/20 amps plug point with modular type 16/20 amps switch and socket including connection with 2x2.5 sq. mm PVC insulated Copper conductor cable (FR) on surface modular switch board, earthing the 3rd pin etc. as required:- (As per TSR 2021, Sl- 204)

13.01 2 x 1.5 sq.mm

13.02 2 x 2.5 sq.mm

13.03 2 x4 sq.mm

14.01 1 X 1.5 sq mm

14.02 1 X 2.5 sq mm

Supplying & fixing of 1200 mm sweep white color AC ceiling fan with brush less dirrect current (BLDC) motor having class B insulation, power factor not less than 0.9 complete with 300 mm down rod, canopies, shackle kit, 3nos blades, safety rope including wiring the down rod with 2x1.5 sqmm PVC insulated copper conductor cable(FR) (BEE 5 star/minimum service value 6.0 m3/min/W & tolerance as per(As per TSR 2021, Sl- 803)

Supplying and fixing of the following electrical accessories including necessary connection etc. as required.:-(As per TSR 2021, Sl- 609) 16.01 5 step fan regulator (2M):-

Supplying & installation of 400 mm sweep AC wall mounting fan with metal blade including connection etc as required:-(As per TSR 2021, Sl- 810)

18.01 Recessed/Surface mounted 2ft x 2ft decorative 36 watt LED panel light with integral driver and high quality polycarbonate diffuser:-

18.02 Recessed round/Square shaped 12 watt LED downlight with integral driver and high quality polycarbonate diffuser:-

18.03 Recessed round/Square shaped 6 watt LED downlight with integral driver and high quality polycarbonate diffuser:-

Supplying and fixing of following Decorative wall mounting LED Fancy bracket light fixture ( Opal glass with chrome finishing ) including necessary connection etc. as required (As per Agreement No. 63/EE-IED/AMB/2022-23):-

Supplying and fixing of following warm white IP54 LED up down wall light (2 X 3 watt) in die cast aluminium housing complete with transparent tempered glass diffuser including necessary connection etc. as required (As per Agreement No. 63/EE-IED/AMB/2022-23):-

Supplying and fixing of 2'X2' LED luminaire suitable for suspended mounting with option of using the back plate of users choice and also ideal for lower ceilings and smaller spaces. (Rate as per Analysis)

Supplying and fixing of Wall Light (ULTRON) 17 watt Grey Colour {Dimension-534(L) x (W) x 33(H)}mm (Model No-480273 of Philips make make price list w.e.f Philips Home Lighting-2023) including necessary connection etc as required:-(As per Agreement No. 64 / EE-IED/ AMB/ 2022-2023)

Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:- (As per TSR 2021, Sl- 1215) 6 to 32 amps SP MCB:-