801638/E8

Amount

BOQ Dated Jul 2025

GENERAL SUMMARY NOTE: Schedule ‘A’ Part IA, II to XII are prepriced by MES under Ser No. 1 to 13. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only.

Lumpsum price worked out by the contractor for “Building or Works” as listed in Schedule ‘A’ Part–IA

Lumpsum price worked out by the contractor for “Internal Water Supply” as listed in Schedule ‘A’ Part–II

Lumpsum price worked out by the contractor for “Internal Electric Supply" as listed in Schedule ‘A’ Part–III

Lumpsum price worked out by the contractor for “Road / Path" as listed in Schedule ‘A’ Part - IV .

Lumpsum price worked out by the contractor for "Area Drainage" as listed in Schedule ‘A’ Part - V .

Lumpsum price worked out by the contractor for “Sewage Disposal” as listed in Schedule ‘A’ Part – VI.

Lumpsum price worked out by the contractor for “Rain water Harvesting” as listed in Schedule ‘A’ Part – VII.

Lumpsum price worked out by the contractor for “External Water Supply” as listed in Schedule ‘A’ Part – VIII

Lumpsum price worked out by the contractor for “External Electric Supply/ DG Set” as listed in Schedule ‘A’ Part –IX

Lumpsum price worked out by the contractor for “Lift” as listed in Schedule ‘A’ Part – X

Lumpsum price worked out by the contractor for "Lightning Protection” as listed in Schedule ‘A’ Part – XI

Lumpsum price worked out by the contractor for "Fire Fighting” as listed in Schedule ‘A’ Part – XII

Lumpsum price worked out by the contractor for "Demolition of existing buildings” as listed in Schedule ‘A’ Part – XIII

Sch 'A' Part - I : BUILDINGS OR WORKS Design and Construction of Multi storey (G+5) Md Accn 30 Airmen Building construction with permanent specifications in RCC of grade as per structural drawings, AAC block masonry walls, ATT, PU based WPT, RCC water tank of 25000 ltr capacity on terrace, earthquake resistance as per latest IS and Green building norms with GRIHA 3 star ratings etc complete all as specified and as shown on drawings.

SCHEDULE "A" Part- XIV (FITTINGS AND FIXTURES & MISC ITEMS)

Supply and fix 15mm bore single lever basin mixer with 450 mm braided connection pipe high neck, bearing ISI mark, cast copper alloy fancy type with capstan heads, chromium plated screw down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed. Make: Jaquar : Cat Part No OPP-15011BPM or Techno commercial equivalent in approved makes specified here in after

Supply and fix brass CP wall mixer 210 mm long bend pipe for overhead shower flanges for mixing of hot and cold water screwed down and fixed complete all as specified and as directed. Make: Jaquar : Cat Part No COP-119 PM or Techno commercial equivalent in approved makes specified here in after

INTERNAL ELECTRIC SUPPLY Supply and fix Surface mounted square/round panel light fitting 12W/18W, 220Volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size and connected accessories etc. complete all as specified and as directed.

Supply and fix Modular TV Socket, one module etc complete all as specified and as directed by engineer in charge .

Supply and fix Modular Telephone socket, RJ-11, one module etc complete all as specified and as directed by engineer in charge.

Material and labour for Telephone Wiring with unarmoured Solid annealed bare copper industrial cable in concealed of size 0.5 mm, 3 pair with PVC Conduit 25 mm dia etc complete all as specified and as directed by engineer in charge.

Material and labour for TV Wiring with unarmoured coaxial cable, RG-11 in concealed with PVC Conduit 25 mm dia etc complete all as specified and as directed by engineer in charge.

Material and labour for Mild steel Box for Telephone wiring including blocks, Suitable for 35 Pair etc complete in all respect all as specified and as directed by engineer in charge.

Supply and fix inverter LED Batten capacity 20Watts 6500 Kelvin with lithium Ion battery charging time 08 to 10 Hours and backup upto 10 Hours complete all as specified and as directed. Make: Havells Cat Part No. Pride plus inverter batten 20 Watts 3500 K V1 or its equivalent in Bajaj / Philips / Crompton

Supply and fix Exhaust Fan / Ventilation fan (heavy duty) of 250 mm sweep made of steel body complete with louvers shutter, voltage 230V, 50 Hz. RPM 1200, Copper winding including writing MES NO. 2 CM height with synthetic enamel black paint etc complete in all respect etc complete all as specified and as directed.

Supply, install, testing and commissioning of smart meter with pre paid metering facility, AC single intergradation phase, two wire, 240 Volts, 50 Hz, 10 to 60 Amps all as per BIS 16444:2015 (Reaffirmed 2020) with plug in type bi directional communication module (The plug in module shall be field swappable/replaceable) suitable for integration with approved communication technology GPRS/RF/Hybrid (GPRS + ) any other advanced technology as per CEA / TRAI regulations etc easily adaptable for network interface and integration with Advanced metering infrastructure (AMI) complete in all respect all as specified and as directed.

ROAD / PATH Material and labour for Providing and laying road marking paint as per IRC 35 with hot applied thermo plastic compound with reflectorising glass beads on bituminous surface, applying of hot thermo plastic compound with minimum 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm inclusive of all surface cleaning, applying, labour charges, all taxes etc at site for complete finished item of work as directed by Engineer in Charge

RAIN WATER HARVESTING Material and labour for bore hole drilling 300mm to insert 200mm dia 8mm thick HDPE perforated casing pipe for percolation of rainwater to ground water table for recharging purpose below ground level in any kind of soil strata including hard stone/boulder including MS cap, MS flat iron clamps, reducing socket etc complete all as specified and directed.

Supply and fix perforated / slotted HDPE pipe of 200mm dia 8mm thick pressure rating of 6Kg/Sqcm length of each pipe 12RM connected as per highest specification and inserted in above drilled borehole and filled with pea gravel surrounding if necessary complete all as specified and as directed.

Supply and fix PVC Cowl of size 200mm dia complete all as specified and directed.

EXTERNAL WATER SUPPLY Supply and fix Open well horizontal submersible Pumping sets of capacity 5.0 HP complete. ( 01- Working & 01 - Standby of 5 HP ) complete all as specified and as directed.

Supply & laying centrifugal cast (Spun) Ductile Iron Pressure Pipe 100mm dia with Spigot & Socket end, Class K-9 conforming to IS : 8329/2000 (latest revision) complete all as specified and as directed.

Material and labour for DI specials i.e. bends, (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch, 'Y' junction, double branch, tail piece, mechanical joints, flange specials, cross ( all socket and spigot) collars, caps and plugs. Upto 100 mm dia complete all as specified and as directed.

Material and labour for construction of brick masonry valve pit of size 90 cm x 90 cm x 90 cm (internal dimension) one brick thick wall in CM 1:4 on 100mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundation, 15mm thick rendering in cement mortar (1:4) internally, externally up to 15cm below GL, providing valve pit cover made out of 3mm thick MS sheet duly welded with provision of hinges, handle and locking arrangement including 40 x 40 x 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embedded in PCC block 1:2:4 type B-1 (20mm graded aggregate) of size 230 X 200 X 100mm, applying two coats of anti-corrosive paint over a coat of red oxide, zinc chrome primer after preparation of steel & iron surfaces including necessary excavation & earth work in hard/dense soil complete as specified and directed.

Supply and Fix Non Return Valve with by pass arrangement of PN 1.6 size 50 mm dia complete as specified and directed.

Supply and fix Cast Iron Air Valves with two air Outlets, 100 mm dia bore and fixing Up in cast iron water supply mains complete as specified and directed.

EXTERNAL ELECTRIC SUPPLY Supply & Fix 3 core 1.5sqmm Flat cable copper conductor PVC insulated PVC sheathed with voltage range upto 1100Volts complete as specified and directed.

Supply Install test and commissioning Feeder pillar box No.1 Indoor type wall mounted insert into wall made out of 3 mm thick MS sheet and angle Iron of suitable size weather proof/vermin proof shutter type with locking arrangement of cubical type prewired with Aluminium busbar 400 Amps for phases and Aluminium busbar 200 Amps and having compartments for each individual qtr with pre-paid meter and controlling wiring for neutral including suitable CTs etc and powder coated painting complete suitable for accommodating the following:- DG LT PANEL

Supply and fix cable route indicator for HT cable made out PCC pole (0.2 x 0.3 x 1) MTRs (LXWXH) on HT cable 0.5 mtr depth grouted in the ground with suitable PCC work with writing HT cable/joint including earth work, PCC block ( 1:3:6) type C1 complete all as specified and as directed.

Supply and fix street light bracket made out of 25mm dia GI tubing medium grade upto 1.5 mtr long including bending, welding, drilling holes as required and fixing with flat iron clamps 32 x 6 mm thick (02 Nos) with suitable nut, bolts and washers to steel tubular/concrete poles/wall complete all as specified and as directed.

Supply and fix LT junction box for street light, sheet moulding compound (SMC) type with hinged type door and locking arrangement, off white colour, of size 300 x 200 x 105mm (internal) comprising of suitable size TPN Aluminium busbar with 200 Amps Phase and Neutral terminals, and 01 No earthing terminal bolt and nut and connecting up cables with aluminium terminal lugs including suitable size MS clamp 2 Nos fabricated from 25x3mm MS flat iron and bolts, nuts and washers complete all as specified and as directed.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and as directed.

Material and labour for returning and filling of trenches in two parts:- (i) using riddled soil obtained from excavated soil up to depth of 30cm (8cm below cable and remaining above cable) for cushioning of cable and (ii) refilling the trench of remaining depth with normal excavated soil all as specified and as directed. Note: Excavated soil shall be riddled by using sieve to separate composite particles etc as per IS-1255-1983 and refilling in trenches as in cable cushioning

DG SET Supply and installation, test and commissioning of acoustic proof diesel engine driven generating set fully wired 415 volts + 5% AC 3 phase 4 wire 50 Hz having capacity 32 KW/40 KVA continuous rating at power factor 0.8 (lagging) as per IS 4722 and connections as per IE rules complete with integrated AMF control panel of suitable capacity with microprocessor based relay and safety accessories as per the latest engineering practices . DG set shall be mounted on common base plate with anti vibration pads and placed on PCC foundation of required size as recommended by OEM. The Gen Set shall conform to latest CPCB norms for noise and emission limits and necessary certificate from NAL or equivalent authority to this effect shall be submitted and complete all as specified and as directed. consisting of the following :-

[a] DIESEL ENGINE. The diesel engine shall be 4 stroke, water cooled, turbo charged developing minimum at 1500 RPM under NTP conditions of BS: 5514. The engine shall be provided with electrical starting arrangement & shall be suitable to produce an electrical output of 32 KW/40 KVA at 0.8 power factor. The engine shall complete with :- Starter motor and charging alternator. Battery as recommended by OEM Dry type air cleaner Fuel pump with injectors A1 class governing Flywheel with flywheel housing Residential silencer First fill of lube oil suitable for 12 Hours continous running at full load Engine protections: Low lube oil pressure & High Water temperature complete all as specified and as directed.

[b] ALTERNATOR. The alternator shall be self excited self regulated brush less and self ventilating type designed for an output of 32 KW/40 KVA, 50 Hz, 415Volts 4 wire continous rating at 0.8 PF, with class 'F' or better insulation, screne protected, drip proof in IP- 21 enclosure and confirming to IS -4722 BS EN 60034-1 and directly coupled with the engine incl control panel with accessories complete with electric supply terminal box with gland plate, earth terminal etc complete all as specified and as directed.

[c] AMF Panel. AMF panel totally enclosed cubical type dust and vermin proof, with sloped canopy, standard industrial pattern, factory fabricated out of 2.0 mm thick CRCA steel sheet painted with one coat of red oxide primer and two coats of anticorrosive synthetic enamel powder coated of approved colour, complete with all mounting structures, insulators, bolts, nuts, washers etc, with necessary control wiring/internal connections with proper size of copper conductor cables / strips, suitable for 3 phase, 4 wire, 50Hz, 415 volts AC system, comprising of microprocessor based AMF relay unit with sensing on mains and DG with necessary safety / protection, MCCB 415 Volt 50 Hz 63 Amp 50 KA rating adjustable microprocessor based 4 pole (as incomming)-02 Nos and 2 Nos 4 pole power contactor of 63 Amps for Mains and DG supply, frequency meter, 3 Phase electronic type AC digital type KWH meter with suitable CTs, electronic earth fault protection relay complete all as specified and as directed.

[d] SOUNDPROOF CANOPY. Soundproof canopy shall be made using 2.5mm thick CRCA sheet for base and Doors & Roof shall be fabricated form MS CRCA of adequate thickness with modular, bolted construction and will have access from all sides with airtight EPDM foam gasket and insulation with fire retardant PU form, MS/Zinc die cast hinges and powder coated with 9 tank pre-treatment process and the finish shall be suitable for outdoor use. The maximum noise level permitted during full load will be 75 dB (a), measured at 1 meter distance from the edge of canopy. The product shall be certified by COCB as per latest norms. Air inlet and outlet louvers, with special sound reduction dampers for proper air ventilation shall be provided. The canopy will have provision of emergency push button which shall be housed in a protective enclosure with a glass front complete all as specified and as directed.

FIRE FIGHTING EQUIPMENTS:- Supply & fix fire hydrant landing valve type A (single head outlet) of 63 mm dia conforming to IS 5290 complete all as specified and as directed.

Supply and fix hose box for hose reel of 20 mm size of 30 meter length complete with coupling branch pipe and nozzle , MS sheet 2 mm thickness complete all as specified and as directed.

Supply and fix hose reel of 20 mm dia and 30 meter length conforming to IS 5132 complete all as specified and as directed.

Supply and fix branch pipe with nozzle of 20 mm dia for hose reel conforming to IS 8090 complete all as specified and as directed.

Supply and fix hose box for keeping 2 Nos hose pipe of length 15 meter each, branch pipe.nozzle, coupling etc of MS sheet of thickness 2.0 mm complete all as specified and as directed.

Supply and fix 63 mm dia gun metal branch pipe with 12.5 mm nozzle conforming to IS 903 complete all as specified and as directed.

Supply and fix 63 mm dia 15 meter long hose conforming to IS 636 complete with male and female coupling conforming to IS 903 complete all as specified and as directed.

Supply and fix 100mm bore hand operated butterfly valve of pressure not less than 15 Kg / Sqcm with complete set complete all as specified and as directed.

Supply and fix Pressure gauge 100 mm dia with ball valve of pressure 25 Kg/Sqcm complete all as specified and as directed.

Supply and fix Gun metal fire brigade in let connection for connecting to external fire hydrant ring main consisting of two nos 63mm dia instantaneous type male coupling with built in check valves and 150mm dia, flanged outlet complete with all accessories complete all as specified and as directed.

Supply and fix Addressable manual call point break glass type with alarm LED complete all as specified and as directed.

Supply and fix Fire Alarm sounders / Sirens electronic type horizontal single stage continuous normal operation for at least 50 minutes with sound level 65 DB to 120 DB measured at 1.5 meter with sound output variation of + 5 DB for 1000 meter range complete all as specified and as directed.

Supply and fix Automatic air release valve 50mm dia suitable for domestic water with 50mm gun metal stop valve complete all as specified and as directed.

Supply and Fix Electric Motor Siren Conforming to IS 1941 suitable For three Phase 415 V Supply with motor not exceeding 3.75 KW Power and able to deliver 143 DB noise level complete all as specified and as directed.

Supply and install Booster Pump for 440V 3 Phase 50HZ confirming to IS 12469 with CI Casing bronze impeller and stainless steel shaft mounted on heavy duty bearings suitable for 18 meters head discharge up to 900LPM complete all as specified and as directed.

Supply and fix Strainer Y type conforming to IS, size 100 mm (4”) dia complete all as specified and as directed.

Supply and fix Fire alarm control panel complying with BS EN 54 Single loop panel of capacity from 99 detectors & 99 modules upto 200 detector complete all as specified and as directed.

Earthing of machinery/equipment installed at power /sub station, using 32x6 mm galvanized MS strip and MS galvanized plate of size 600mm x600mm x 6 mm as earth electrode complete all as specified and as directed.

Supply and fix MS flanged pipe 100mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer complete all as specified and as directed.

Supply and lay Pipe galvanized 'Heavy Class' including fittings 63mm (21/2" dia) complete all as specified and as directed.

Supply & Laying of 2 Core, 1.5 Sqmm Un-armoured PVC insulated & sheathed copper flexible cable complete all specified and directed.

Supply and laying of 6 fiber single mode, armoured, ISO/IEC-11801, EN50173, ANSI/TIA-586-C3, fibre optic cable complete all specified and directed.

Supply and laying HDPE Pipe 25mm dia complete all as specified and directed for OFC cables complete all specified and directed

Supply, Installation, Testing & Commissioning of remote controlled terminal fault tolerant (Repeater Panel) complete all as specified and as directed.

Supply, installation, testing & commissioning of 6 zones System controller Panel with built-in DVR, having priority facility, music and Pre recorded fire evac message. Controller can be extended upto 100 zones complete all as specified and as directed .

Supply installation, testing & commissioning of 6 zone Call Station keypad with for PA system Announcement with goose neck microphone and with LCD display to announce all the zones or individual zones complete all as specified and directed.

Supply & Laying of 4 Core 1.5 Sqmm Un-armoured cable complete all as specified and as directed.

Supply and fixing in position various signage boards at different locations of any size as per site requirement. It should containing the letters on 5mm thick self illuminated opaque PVC foam board of computerized letters, PVC non reflective self adhesive vinyl painted foam board of different sizes including all fixing arrangement complete all as specified and as directed. Note : The board shall be fixed on wall with suitable chromium plated screws including washers, the letter size shall be not less than 40mm with approved colour.

Supply and fix cable route indicator made out of 3 mm thick MS sheet of suitable size (As approved by Engr-in-charge) duly painted with two coats black paint over a coat of red oxide primer and writing cable direction, Nature of cable (i.e. Fire Alarm Cable), size of cable (in SQMM), type of cable (OFC/PVC) with white paint, mounted on angle iron 40x40x3 mm, angle height 45 cm, (30cm below ground level) with PCC 20cmx20cmx15cm all as specified and as directed

Supply and fix Fire Extinguisher water based type of capacity 9 Ltrs complete all as specified and as directed.

Supply and fix Fire Extinguisher Dry chemical powder (ABC) type of 09 kg capacity complete all as specified and as directed.

Supply and fix Fire Extinguisher Dry chemical powder (ABC) type of 04 kg capacity complete all as specified and as directed.

Supply and fix Fire Extinguisher Co2 type of 3.0 kg Capacity squeeze Grip operated, light weight as per IS-15683 complete all as specified and as directed.

Supply and fix Fire Extinguisher Co2 type of 4.5 kg Capacity squeeze Grip operated, light weight as per IS-15683 complete all as specified and as directed.

Supply and fix Fire Extinguisher Mechanical Form type 9 Ltrs complete all as specified and as directed.

Schedule 'A' Part - XV (Outsourcing services for operation of lifts) Out sourcing man power for maint and operation of (01 x 08 passenger lift and 01 x 13 passenger lift) at Airmen MD Accn by deploying one no lift operator (per shift) for three shift (03 No lift operators) each shift shall be 08 hours timing to 0600 Hrs to 1400 Hrs, 1400 Hrs to 2200 Hrs and 2200 Hrs to 0600 Hrs including sundays and holidays complete all as specified and directed. First year after completion of Phase-I

Notes:- (i) Lift operator shall have ITI certificate in the trade fitter/ mechanic / Electrician / 10+2 with minimum 3 years experience in relevant trade (ii) Contractor shall ensure that, no outsourced worker is employed more than eleven months in a single stretch. (iii) No operator/ helpers shall be made to work more than 08 hours in a day and more than 6 days continuously in a week. Sufficient relievers may be provided to ensure the same. (iv) A supervisor having diploma in Electrical/ Mechanical Engineering with three years of experience may be additionally employed for coordinating with the Department. (v) All the operators and supervisor should have fluency in English, Hindi and local language and shall have good communication skills and mobile phone for communication. They shall be equipped with all tools and safety gears required for operating the plants/ equipments and shall wear uniform as approved by Engineer In Charge during duty hours. (vi) As per amendment to payment of wages Act 1936Act, issued in the Gazetter Notification dated 15 Feb 2017 "All wages shall be paid by cheque or by crediting the wages in the bank account of the employee for this contract, the payment shall be mede into Aadhaar linked bank account of the employee by the Contractor. (vii) The GE being the principal employer is responsible to ensure that the contractors fully comply with the labour laws. The contractor shall be primarily liable for all payments to be made under and for observanceof the regulations aforesaid with out prejudice to his right to claim indeminity form his sub contractors. The principal Employer shall have the right to deduct from paymentdue to contractoe, any sum required or estimated to be required for making good the loss suffered by a worker or workers, of non fulfilment of the conditions of the contract for the benefit of the workers, non payment of wages or of deductions made from his wages which are not justified by the terms of the contract or non observance of the Regulations. (viii) The contractor shall keep registers, records, dispaly Notices at the site to adhere the labour regulations. (ix) GE being the Principal Employer shall enter the details of Contractor in the EPFO portal after conclusion of contract. The payments due to the contractor shall be mde only after verfying the statutory PF payments have been made to EPFO. This can be verified either directly from EPFO portal ot insisting on a payment receipt obtained by the contractor from the EPFO portal while making payment. (x) Submission of proof of crediting the wagesin the Aadhaar linked bank account payment made to the employees by the contractor, shall be a preequisite to enable the contract executing authority to release sussequent payments to contractors . The registered contractor shall also provide details of individual's EPF and ESI account number to claim the payment and contract executing authority will ensure verification of the same from time to time. (xi) No payments to the contractor/firms will be made by the GE unless proof iof payment of wages through Aadhaar linked bank accounts is submitted by the contractor / firms to the Engineer in Charge and there after Engineer in Charge to GE. (xii) A penalty of Rs 2000/per day will be imposed on the contractor if the lift operator is found absent from duty on any day.

All as per serial item No.81 but for second year after completion of main project (Phase-I)

Schedule 'A' Part - XVI (Comprehensive maintenance of lifts and outsourcing of services for operation of Lifts) All as per serial item No.81 but for Third year after completion of main project (Phase-I)

All as per serial item No.81 but for Fourth year after completion of main project (Phase-I)

All as per serial item No.81 but for Fifth year after completion of main project (Phase-I)

Comprehensive AMC for the lift through OEM during first year post defects liability period (01 x 08 passenger lift and 01 x 13 passenger lift) this includes regular inspection servicing and maint of the lift components, lubrication of all moving parts and cleaning of lift shaft and pits. Schedule preventive maintenance of as per OEMs recommendations replacement of worn out parts including batteries and other moving parts prevent breakdowns. Testing and calibration of safety devices to ensure function correctly 24x7 emergency call out services to attend lift breakdowns are malfunctions

All as per serial item 86 for but Second year after completion of Phase-II i.e After the expiry of Defects Liability Period.

All as per serial item 86 for but Third year after completion of Phase-II i.e After the expiry of Defects Liability Period.

M/s Imperial Coastal Infra (BID ID -3375627)

P L ADKE (BID ID -3376376)

GOVARDHAN AND COMPANY (BID ID -3377108)

S Balbir Singh (BID ID -3377264)