REPAIR TO SUNKEN PORTION, FLOORING, SANITARY FITTINGS AND PLASTER ETC AT MH AND ADJOINING AREA UNDER GE (ARMY) NO 2 JODHPUR

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for (such as copings, bands of any type, roof padding, kerbs, sunken etc; overall thickness and removing the dust debris etc to a distance not exc 250 meter from site and disposing the same complete all as specified and as directed

M&L for plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregates as over roof for making good depression / undulation to make the existing roof surfaces as filling in depression of roof slab / floor padding / roof kerbs rounded or chamfered on edges coping etc (average thickness not exceeding 25 cm); complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor not exceeding 15cm thickness below or above ground level including floor finishes and removing debris from the site complete all as specified and as directed

Dismantling glazed tiles/ kota stone/ terrazzo tiles any type as in dado/ skirting etc; including cement mortar bedding ( but not backing ) complete all as specified and as directed

M&L for Vitrified ceramic tiles 10mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for Vitrified ceramic tiles 10mm thick (square/ rectangular) as in skirting / dado, cut out of ceramic tiles of size not exceeding 0.36 sqm, (Matching with floor tile of the same room) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for Vitrified ceramic tiles 10mm thick (square/ rectangular) area of each tile exceeding 0.42sqm but not exceeding 1.00sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for Vitrified ceramic tiles 10mm thick (square/ rectangular) as in skirting / dado, cut out of ceramic tiles of size each tile exceeding 0.42 sqm but not exceeding 1.00sqm, (Matching with floor tile of the same room) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for non skid ceramic tiles 10mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for non skid ceramic tiles 10mm thick (square/ rectangular) as in skirting / dado, cut out of ceramic tiles of size exceeding 0.18 sqm but not exceeding 0.38 sqm, (Matching with floor tile of the same room) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles of approved shade and pattern, 7 to 8 mm thick , area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm laid in floor, set and jointe (square/ rectangular) in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of approved shade and pattern of size 350x 250x7mm/ 450X350X7mm/ 300X450X7 to 8mm thick or any other nearer size as approved by Engineer incharge in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 as in backing coat of tiles complete all as specified and as directed.

M&L for 16 -18mm thick granite (colour as approved) work (table rubbed and polished) in steps, shelves, jambs, pillars, window-cills, cooking platforms (vertical/ horizontal) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-20 mm (+ 2mm) thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for mirror polished machine cut kota stone slab 15-16 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 and jointed complete all as specified and as directed.

Dismantling of stone/ brick work masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work, serviceable stone aside for reuse and removing unserviceable material in low laying area complete all as specified and as directed.

M&L for squared rubble walling jodhpur type, brought upto course, well bonded bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

-ditto- all as per above item but, except stone complete all as specified and as directed.

Extra over for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling,Jodhpur type, brought upto courses all as specified and as directed.

Taking down cement plaster, any description, on brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water etc and disposal of debris complete all as specified and as directed

M&L for rendering 15 mm thick in CM (1:6) over stone masonary, concrete surfaces, finished even and smooth (without using extra cement), complete all as specified and as directed

M&L for 15 mm thick rendering on stone masonary wall surfaces in CM (1:4) finished fair and even all as specified and as directed.

M&L for 10mm thick rendering in CM 1:3 on ceiling surfaces finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for carrying out water proofing treatment for sunken portion in the following stages - (i) Taking down of existing sunken slab treatment from the sunken portion and cleaning the surfaces washing down with water and rubbish of the pemises , cleaning and filling cracks with sealing compound, brushing neat cement slurry @ 3.00kg/sqm and grouting 25mm thick cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate on sunken slab portion and finishing the top surfaces even and smooth without using extra cement. (ii) M&L for two coat of acrylic cementitious water proofing coating (Dr FIXITpidifin 2k manufactured by M/s Pidilite Industries Ltd or equivalent) and followed by a overlay protective screed (10mm thick cement mortar (1:4) along with liquid water proofing compound approved make as per manufacturer's instructions) on top surfaces of sunken slab after preprations as mentioned above. Method of application for acrylic cementitious water proofing coating achieved as per manufacturers instruction complete all as specified and directed.

Supply only integral water proofing liquid ISI marked

Dismantling cast iron work of any description and in any position complete all as specified.

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc complete all as specified and as directed

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc complete all as specified and as directed

S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc complete all as specified and as directed

S&F 100mm bore pipe cast iron 'P' or 'S' trap complete all as specified and as directed

S&F 75mm bore pipe cast iron 'P' or 'S' trap complete all as specified and as directed

S&F 100mm bore pipe cast iron cowls complete all as specified and as directed

S&F 75mm bore pipe cast iron cowls, complete all as specified.

M&L cast iron up to 150mm bore fittings of Bends (any type, radious and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces, single branch, 'Y' junctions, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc; complete all as specified.

M&L 100mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified.

M&L 75mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified.

S&F for 100mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified.

S&F for 75mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified.

M&L for cement concrete type E-2, 1:5:10 (40mm graded crushed stone aggregate) as in sunken portion complete all as specified.

S&F 40mm bore steel water tubing medium grade galvanised inserted at the end of lateral slope projecting at least 15cm beyond the outer most projected part of the building below the drain pipe up to two storey construction as spout for sunken complete all as specified and as directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing from site or to store complete all as specified and as directed

Taking down shutters any description exc 1.00 sqm but not exc 2.00 Sqm each and removing from site or to store complete all as specified and as directed

Taking down shutters any description exc 1.00 sqm but not exc 2.00 Sqm each and refixing the shutter in same opening after easing and adjusting complete all as specified and as directed

M&L for fabrication of aluminium powder coated window any pattern & design (openable with hinges, sliding, tilt and turn, casement , fixed type, villa type, ventilators) fabricated with anodized aluminium rectangular or any type section in frame with approved design & patterns including provn of fixing galvanised mild steel wire cloth on the outer side of frame etc; fixed in position all as specified and directed. Note:- Glass pane & galvanised mild steel wire cloth shall be measured and paid separately under respective Items of Sch 'A'.

S&F for figured glass, pin head type ordinary quality, 5mm thick, area of each pane not exceeding 0.5Sqm and glazing with aluminium beading in aluminium frame all as specified and as directed.

S&F of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & as directed.

S&F of factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing S&F. Make : Rajshree Doors or equivalent as approved by GE.

S&F of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F of 100 mm size PVC/ Stainless Steel (as approved by Engineer incharge) butt hinges all as specified and directed.

S&F of alluminium anodised handles 150 mm long, complete all as specified and as directed.

S&F of aluminium anodised, barrel tower bolts 150mm long of extruded section, complete all as specified and as directed.

S&F of powder coated aluminium anodised deco grill weighing not less than 1.40 kg/ sqm and fixing necessary joining cleats/ frame etc complete all as specified and as directed

Taking down 15mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specified and as directed

Taking down 20mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specified and as directed

Taking down 25mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specified and as directed

S&F 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed

S&F 20mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed

S&F 25mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed

Fixing only 15mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed

Fixing only 20mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed

Fixing only 25mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed

M&L vitreous china wash down water closet pan (pedestal pattern), white including white plastic seat cover with mild steel CP hinging device, suitable brass CP wash jet with 1.00 to 1.50m long tube (Make of Jet 'Praayag' Cat Part No 5211 or Equivalent) incl making connection to inlet flush pipe, & to 'P' or 'S' drain trap, incl supply of long special 'P' or 'S' trap fixed in repair complete and making good the disturbed portion etc.complete all as specified and as directed

Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc complete all as specified and as directed

S&F in repair PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc complete all as specified and as directed

S&F in repair vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified and as directed

Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified and as directed

Disconnecting existing PVC tank exc 500 Ltrs and not exc1000 Ltrs setting aside (or lowering if required) for repairs, cleaning (Cleaning and removing all scale and dirt, etc; from tanks and from mouth of circulating pipe etc;) and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

S&F in repair 500 ltr capacity rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) and in white colour hoisted and fixed in position including 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified and as directed

S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) and in white colour hoisted and fixed in position including 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified.

S&F in repair 15mm bore chromium plated bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed

S&F in repair pillar tap, brass, 15mm dia, with capston heads, chromium plated, fancy type screwed down, high pressure, with or without lettered hot or cold, with long shank, screwed shanks and fly nuts, screwed for iron pipes or for wash hand basin all as specified and as directed.

S&F in repair 15mm bore stop valve/ angle stop cock chromium plated, fancy type cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe with long shank and cup complete all as specified.

S&F in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed

S&F in repair chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union suitable for 15mm bore pipe etc; complete all as specified and as directed

S&F in repair CP greating doom 100-125mm dia complete all as specified and as directed

S&F 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (minimum weight for 25mm ball valves-455gms) fixed in repairs i.e., incl taking down and removal of old unserviceable float valves complete all as specified and as directed.

Preparing new plastered surfaces and M&L for applying chalk whitening/ concrete primer and /or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of Distemper oil Emulsion complete all as specified and as directed.

Preparing new plastered surfaces and M&L for applying concrete primer and /or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and two coats of cement base paint complete all as specified and as directed.

Preparation of new plastered surfaces of walls etc. & applying three coats of lime white wash complete all as specified and as directed.

Preparation of new plastered surfaces of ceiling etc. & applying three coats of lime white wash complete all as specified and as directed.

Diva Infra

Bhagwati Construction Company

G D ENTERPRISES

M/S PIYUSH CONSTRUCTION COMPANY

PANWAR ELECTRICALS

SURESH TRADERS

M/S Dharam Chand Lal Chand Jain