PROVN OF TOILET BLOCK NEAR COY LINE AT INF BN, 10 x 500 LTR AND 01 X 2000 LTR PUFF TANKS FOR HIGH ALTITUDE WARFARE SCHOOL AT GULMARG AND SPL REPAIR TO BLDG NOI T-10 SPWD (MUSEUM HALL) IN HAWS GULMARG TO ROAD FROM BN MANDIR TO NEW AT HAWS AT GULMAR

Amount

Dismantling wall and ceiling boards (Fibre, pulp, insulation etc) and bording any thickness including cover fillets complete complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge and thickness in roof covering including Nainital or similar pattern roof covedring complete all as specified.

Dismantling boarding, any description fixed in any position with nails.

Dismantling timber scantling 40 Sqcm and over in section in any position unframed work.

Dismantling timber scantling in fillets rails, posts, purlins etc under 40 Sqcm in section in framed work.

Demolition of cement concrete in ground floors and pavings n.exc 15cm depth (below or above ground level).

Excavation in trenches in any type of soil, n exc 1.5 M wide and n exc 1.5 M deep for foundation, etc or for shafts, wells, manholes etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in any type of soil complete.

M&L TMT bars 10mm dia and over cut to length, bend to shape required including cranking, bending spirally for hookings for cols, hooking ends and binding with and including mild steel wire (aneeled) not less than 0.9mm dia complete all as specified.

All as per srl item No 08 but 5mm dia and above including 10mm dia in stirrups.

M&L Plain Cement concrete Type D-2, 1:4:8 (40mm graded aggregate), in foundation, filling and mass concrete complete all as specified..

M&L Plain Cement concrete Type C-2, 1:3:6 (40mm graded aggregate), in foundation, filling and mass concrete complete all as specified..

Returning filling in incl spreading leveling, watering and well ramming in layers n exc 25 cm all as specified.

Removing of excavated soil not exceeding 50m and depositing where directed at a level not exc 1.5 M above the starting point all as directed by Engr-in-charge.

M&L for walling of random rubble masonry built in CM 1:6 brought up to courses complete all as specified..

Extra over hammer dressing to face stone and dressing of face beds with maximum depression on face from straight edge n.exc 40mm complete all as specified.

M&L for raised pointing to random or polygonal rubble uncoursed brought up to course in CM 1:4 complete all as specified.

M & L Providing cement concrete Type B-1, 1:2:4 (20 mm graded crushed stone aggregate) as in copings, plinth Course, bond stones including use of form work all as specified and directed.

M & L Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified.

M & L Brick work with sub class ‘B’ bricks, straight or curved on plan any radius in half brick thick wall with old size bricks built in cement mortar 1:4 complete all as specified.

M & L Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces with using integral waterproofing compound including finishing the surface even and smooth without using extra cement complete all as specified. (supply only of W P C shall be measured and paid separately).

M & L Rendering 10 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound. Make :- Pidilite/Sika/Fosroc/STP

Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified.

M & L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified..

M&L 100 mm thick Cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing complete all as specified..

M&L 75 mm thick Cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring complete all as specified..

M&L 50mm thick PCC 1:3:6, type C-2, (40mm graded aggregate) as in plinth protection and similar works including finisheing the surface of concrete topping even and fair, without using extr cement complete all as specified.

M & L 75mm thick PCC (1:3:6) type C-2 using 20mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified.

S & F Roof trusses, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. (unframed work) complete all as specified.

M & L Preparation of new steel surfaces of any description over 10 cm width or girth and priming with red oxide zinc chrome and painting with two coats of synthetic enamel paint on Steel sheeting as in roofing complete all as specified.

Preparing new zinc (or galvanized) surfaces to receive painting by coating with mordant solution including washing and cleaning etc. of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

Preparation of old painted zinc or galvanised surface of any description and in position and applying one coat of synthetic enamel paint all as specified. Note :-(a) The surface of corrugated steel sheeting shall be measured flat (not girth) without any extra allowance for laps and the area obtain shall be increased by 14%). (b) The surface of plain steel sheeting as in ridge, hips, velley gutters, flashings etc, shall be measured flat alongwith girth (length and firth as fixed) and the area obtained shall be added to the area of corrugated steel sheeting

S&F stainless steel (Grade 304) railing made of hollow tubes, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts with bolts complete, including fixing the railing with necessary accessories compete all as spd ( Dia baluster and top rail is 32 mm and spacing of bulaster is 600 mm,heigh of railing 900mm) design and pattren as directed by Engr-in-Charge.

M & L for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for fair finished surfaces in any position flat or curved complete all as specified.

M & L for form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc, also splays between floor and beams, etc in rough finished surface of concrete.

M & L for form work to sides of pillars (square/rectangular or polygonal), posts, struts, piers, columns and stanchions etc in rough finished surface of concrete.

M & L for RCC M-25 Design Mix (20 mm graded aggregate) in foundations, incl rafts, footings, foundation beams, plinth beams, bases for columns etc basement slabs, under-reamed piles and mass concrete complete all as specified.

M & L for RCC M-25 Design Mix (20 mm graded aggregate) in beams and columns in floors , roofs , landing , balconies , canopies, deck slab and in shelves and the like complete all as specified..

M & L for RCC (Design Mix M-25, 20 mm graded aggregate) as in beams, cantilever, bressummers, lintel over 1.5 m span complete all as specified.

M & L for 0.63mm thick galvanised corrugated or semi-corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating in roofing fixed with new J-hooks/L-hooks/cranked hook bolts etc complete all as specified. The sheets shall be conforming to IS make.

All as per srl item No 41 above here-in before but except sheets.

M & L for 0.80mm thick plain Galvanised mild steel sheeting, in ridges, hips, fascia boarding, valley gutters, drip and straight flashings (length and girth as fixed with grade of zinc coating fixed with new J-hooks/L-hooks/cranked hook bolts etc complete all as specified. The sheets shall be conforming to IS make.

S&F second class softwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps.

S&F second class softwood 20mm thick facia boarding fixed with nails in any situation planed one side with butt joints complete all as specified.

Hacking out old broken glass from wooden/metal frame of any thickness incl punching or drilling out old glazing pins/springs clips and providing and fixing new ones complete all as spcified.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (W/out taking off shutters from the frames).

S & F for 2nd Class Hardwood in Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered,put together with glue pinned at joints complete all as directed.

M&L for 30mm thick Ist class softwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium densite, wood particle board with commercial face veneers and fitted to chowkats.

S & F Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed.

M&L for 6 mm thick veneered decorative Ply wood, grade 1 (with BWR resin) with decorative face veneers on one face has decorative veneer fixed with nails to timber frame work on ceiling etc. complete all as specified.

S & F Second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 6 and not exceeding 13 Sq. cm complete all as specified and directed.

S&F second class softwood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exc 13 and n.exc 25 Sqcm complete all as specified and directed.

M&L for 6mm thick plywood , grade BWR type BB, fixed with nails to timber frame work on walls etc. complete all as specified.

M&L for second class softwood 15mm thick planed on both side and edges tongued and grooved or rebated and joints are chamfered one side and the boarding is matched, fixed with nails in walls including preparing the surface and applying french polish over a coat of wood filler pn new work with two or more coats complete all as specfied and directed by Engr-in-Charge.

M&L for 12mm thick plywood , grade BWR type BB, fixed with nails to timber frame work in ceiling etc complete all as specified..

S&F decorative wooden tiles of size 300x300x10mm of second class softwood, design and shade as approved by Engr-in-Charge.

M&L second classhard clean sawn as in scantling in framed work.

All as per Ser item No 59 above but except timber only.

S&F second class softwood boarding in floor and skirting 40mm thick planed one side with butt joint and fixed with nails for repair to existing floor in patches etc.

All as per above item here-in before but except boarding fixed with nails.

M&L for two coat of synthetic enamel paint over a coat of pink primer including on surface of wood or wood based of any description, complete removal of snowcem/white wash etc. complete all as specified.

M & L Painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete all as specified.

Prepartion of old painted surfaces of wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint all as specified.

M & L PCC 1:3:6 type C-1 using 20mm graded stone aggregate for hold fast blocks, including necessary form work for rough finished surfaces etc complete all as specified.

S & F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates, hook and pintle hinges: large hasps and stapples , chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two ways and three ways straps, plate washers and similars small articles conforming to Fe-290 Gde E-165. complete all as specified.

S & F Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified.

S&F 100 mm long extruded brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F 300 mm long brass sliding bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified.

S & F 200mm long, brass barrel tower bolts, of extruded section ISI marked complete all as specified.

All as per srl item No 71 above but 150 mm length of bolt.

S&F 150mm long extruded brass handles cast type polished complete all specified and as directed.

S & F Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified.

M & L 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, including finishing surface of concrete topping even and rough complete all as specified.

M & L Non skid coloured ceramic tiles 300x300x 6-7mm thick in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified.

M & L Glazed ceramic tile 450 x 300 x 06-7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick plaster in cement and sand mortar 1:4 complete all as specified.

S & F for 4 mm thick figured glass pin head ftype and glazing with oil putty in squares n.exc 0.5 sqm in each pane.

M & L sheet glass ordinary quality 4.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window frames.

S&F steel ventilators with top hung shutter including hingessteel peg sta, compoete all as specified.

S & F for PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for 75 mm bore of pipe.

All as srl item no 81 above but 110mm bore of pipe.

S & F for PVC (SWR) branch piece equal or unequal, plain including jointing with solvent cement 75 mm bore complete all as specified.

All as srl item no 83 above but 110mm bore.

S & F for PVC (SWR) vent cowl, plain including jointing with solvent cement 75mm bore complete all as specified.

S & F for PVC (SWR) floor bend, plain including jointing with solvent cement 75 mm bore complete all as specified.

All as srl item no 86 above but 110mm bore.

S & F for PVC (SWR) reducer pipe piece, plain including jointing with solvent cement 110 mm bore complete all as specified.

S & F for PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore complete all as specified.

S & F for 125/110 mm PVC (SWR) gully trap, plain with grating including jointing with solvent cement complete all as specified.

M&L steel water tubing med grade galvanised with full fitting and fixed complete to wall or laid in floor boare of pipe 15mm complete all as specified.

M&L steel water tubing med grade galvanised with full fitting and fixed complete to wall or laid in floor boare of pipe 20mm complete all as specified.

S&F Ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe 20mm bore complete all as specified.

S&F 15 mm bore angle cock, fancy type chromium plated high pressure with crutch or butterfly handle, screwed both ends for iron pipe, complete all as specified.

S&F bib taps fancy type long body chromium plated 15mm dia cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed in repair incl extn piece and base plate all as specified and directed.

S & F Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc , complete all as specified.

S & F PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 90 cm long etc, supplied and fixed, complete all as specified.

S & F Vitreous china wash basin, white, flat back, size 550x400mm including pillar tap, waste fitting chromium plated brass and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe and pillar tap etc., fixed complete all as specified.

S&F 1000 ltr capacity rotational moulded polythylene in white coloured three layered ISI marked water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all all as specified in SSR part -I.

S&F urinal vitreous China , Flat back of size 465x355x265mm white with grating and union for discharge pipe , complete including providing and fixing plugs, bedding urinial against in wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinial back in cement ,including 32mm bore PVC waste pipe complete all as specified.

S & F PVC connection 15 mm size, of length 450 mm, with PTMT nuts supplied and fixed complete all as specified.

M & L Cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in surface channels, drains etc.

Extra for forming fair faces (finished) drain of channel 30 cm inner girth in cement concrete using extra cement including forms moulds mitered stopped end etc complete all as specified and directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in any type of soil all as directed by Engr-in-charge.

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid on sand chusioning with Grey cement and no pigment , complete all as specified and diected.

M & L Sand filling under floors or in foundations including watering and consolidation complete all as directed

M & L Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges complete all as directed

LLDPE Septic tank exc inordinary soil , foundation in PCC 1:2:4 brick work in CM 1:4 RCC slabs covers including RCC precast Manhole cover having 6mm Plate embedded all arround/fiber reinforced cover with angle iron frame vent shaft and sludge chamber etc complete for 20 users complete all as specified as per manufactures instructions .

Soakage well Exc in Ordinary Soil foundation in PCC 1:3 well of honey combed and soild in M-25 concrete including intercepting chamber screen chamber bricl work in 1:4 CM , RCC cover Slab in M-25/RR masonary /filling with bricks Bats , complete of size 2.40 Mtr dia x 3.00 mtr deep complete all as specified and shown in drg No CESZ/TD-1080/2011.

M & L precast RCC man holes cover in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate.

M & L for 150mm dia Reinforced concrete pipes, class NP3, laid and jointed complete with collars

M&L for concrete bed to drain pipes in PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate including packing under haunching against the sides of pipe after they are laid and tested for 150mm dia.

S&F FRP Rotex PUF insulated tanks 500 ltr capacity consists of outer layer of tank white in colour made up of virgin FRP, inner layer of tank white in colour made up of virgin LLDPE/HDPE, in middle of both the layers polyurethane foam (PUF) of 50mm thick, including inlet alongwith float valve ,outlet ,overflow provision and tank lid with a suitable locking system complete all as specified and directed.

S&F FRP Rotex PUF insulated tanks 2000 ltr capacity consists of outer layer of tank white in colour made up of virgin FRP, inner layer of tank white in colour made up of virgin LLDPE/HDPE, in middle of both the layers polyurethane foam (PUF) of 50mm thick, including inlet alongwith float valve ,outlet ,overflow provision and tank lid with a suitable locking system complete all as specified and directed.

M&L For repair to surfaces of macadam Roads by scarifying or picking gravelled macadam or bituminous macadam surfaces in area exc 400 sqmm and n exc 50mm deep,complete all as specified and directed.

Rolling and consolidation formation in cutting with roller using 8 to 12 ton power roller complete to required level,gradient,slope,camber,super elevation including filling depression and including approved earth which may occur during rolling process all as specified.

M&L 150mm thick cement concrete work in pavement of flexural strength 40 kg per square centimetre in field using 400 kg of cement per cum thickness of concrete 25 cm or less.

Formwork to edges of concrete flats, treads, breaks in floors, opening in concrete walls, floor and roofs n exc 200 mm wide and sides of RCC/PCC bend in walls, horizontal or slopping and similar work exc 10 cm but n wxc 20 cm wide.

M&L forming 12mm thick expansion joints for 150mm thick concrete filled with preformed bituminous filler and top 30mm primed and sealked with sealing compund gradeA complete all as per specofied and directed.

M&L forming contraction (dummy) joints 65mm deep X 10 m wide filled with sealing compund A grade.

Forming construction joint 150mm deep X 10mm wide filled with sealing compund

M&L moorum/red bajri fillking in floors or pavings laid in layers n exc 15cm thick , spread,levelled and rammed including watering

Removing excavated materials exc 250m but n exc 500m and depositing wehere directed at a level n exc 1.5m above the starting point.

M&L for point wiring in PVC casing caping with 1.5 Sqmm size multi stranded FRLS copper conductor cable 1.5 Sqmm including clamps,screws gutties/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated FRLS cable of size 1.5 Sqmm as earth continuity conductor.

a) One light/fan point/ex fan point controlled by one 5 Amps switch one way

S&F switch piano Flush type,single pole,one way 6 Amp 240 Volts,complete all as specified and as directed.Make:Anchor/Bajaj/Cona Note: Taking down of switches included in taking down point wiring

S&F Ceiling rose 3 terminal/PVC/Polycarbonate,Isolated body.

S&F Lamp holder,PVC/Polycarbonate type with back plate suitable for batten fitting complete all as specified and as directed.

S&F Distribution board,SPN 4 Way,single door complete all as specified and as directed.

S&F 240V,10 KA'B'Curve miniature circuit breaker(MCB)of single poles and current carrying capacity 5 to 32 A in the MCB DB complete with connection testing and commissioning make : Anchor/Havells/Indo asian or equivalent

S&F amp rating 240V,10KA 'C' curve miniature circuit breaker(MCB)of SPN and current carrying capacity of 32 Amp in the MCB DB complete with connection testing and commissioning.

S&F in repair LED bulb thread/Pin type of capacity 10 Watt complete all as specified.

S&F LED light fitting 1 x 10W bulk head luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed

S&F LED lights fitting 1 x 20W,4ft,220V AC decorative box type with driver,holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete complete all as specified and as directed by Engr in Charge

S&F LED light fitting mirror type with high output diffuser 2 ft,10W,220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F exhaust fan,steel body AC single phase,230V of size 300MM sweep with blades and frame and louvers complete all as specified and as directed by Engr in Charge.

M&L for earthing complete with galvanised steel earth plate electrode 600mm x 600mm x6mm thick burried directly in ground(Earth Pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5M below normal ground level connected to galvanised earth wire of 4mm dia(Upto 7.5M in length from earth plate) by means of bolts & nuts check nuts and washers of galvanised iron or steel all as specified and shown in electrical plate no.5 of SSR partI including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40mm thick cover with MS rod 6mm dia at 150mm c/c in both ways as reinforcement,watering funnel,20mm dia light grade for protection of earth electrode,20mm dia GI pipe light grade for watering complete all as specified and as directed by Engr in charge and tested on completion. Note: The rate is inclusive of necessary earth work,RFR and removal etc.

Supply and laying and testing cable XLPE insulated, Screened,PVC bedded,galvanised steel strip or wire armoured electric power cables(heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 sqmm 2 core complete all as specified.

Sub class B common klin burnt clay building bricks,old size 230mm x 115mm x 75mm,laid at right angle along the cable over sand cushioning,as cable protection, complete all as specified.

S&F 50mm dia GI tubing,medium grade ISI marked complete with all fittings,laid in trenches or laid under floors,fixed on walls with and providing clamps etc complete all as specified & directed

S&F 25mm dia GI tubing,medium grade,ISI marked complete with all fittings,laid in trenches or laid under floors,fixed on walls with and providing clamps etc complete all as specified & directed.

Cutting of existing GI pipe line of size 50mm dia and inserting new pipe line including all fittings complete all as directed

S&F of gun metal,globe or gate valves,with iron wheel head,screwed both ends for iron pipe or unions and fixed complete including taking down of old one suitable of 50mm dia sizes all as specified and directed by Engr in Charge

S&F of gun metal,globe or gate valves,with iron wheel head,screwed both ends for iron pipe or unions and fixed complete including taking down of old one suitable of 25mm dia sizes all as specified and directed by Engr in Charge

Taking down carefully copper/ aluminium point wiring (light, Fan, Socket or Power) complete incl fittings such as switches,ceiling roses,pendants,regulators,sockets etc removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls floors etc.

M&L for point wiring in PVC casing caping with 2.5 Sqmm size multi stranded FRLS copper conductor cable including clamps,screws gutties/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated FRLS cable 2.5 sqmm as earth continuity conductor

S&F Modular switch 1 Way 6A,1Module,240Volts,complete all as specified and as directed by Engr In Charge Make: Anchor/Bajaj/Havells or equivalent Note: Taking down of switches included in taking down point wiring.

S&F Switch socket combination 16A,6Pin,3Module,2in1,flush type universal complete all as specified and as directed by Engr in Charge Make : Anchor/Bajaj/Havells or equivalent

S&F Distribution board,SPN 12Way,single door complete all as specified and as directed.

S&F amp rating 240V,10KA 'C' curve miniature circuit breaker(MCB)of SPN and current carrying capacity of 40 Amp in the MCB DB complete with connection testing and commissioning Make: Anchor/Havells/Indo asian or equivalent

S&F LED luminiare 600mm x 600mm,35/36 Watt,220V AC recessed type with high efficiency PMMA difusser soft glare free light complete with driver,holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engr in Charge.

S&F round shape 6 Watt 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers,holders LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete

S&F LED Surface mounted spotlight in matt finish of 7 Watt 3000K for premium asthetics,including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr in Charge.Make:Havells Cat part No LHEEGBPBPH1W007 or equivalent.

Note:- Schedule of credit Rs. 38,027.00 will be deducted from total amount quoted while accepting the bid. Details of schedule of credit is given in tender documents.

M/S HAJI MOHD ASHRAF SUMJI

M/S GHULAM QADIR WANI AND SONS