CONSTRUCTION OF INDOOR BADMINTON COURT WITH ALLIED FACILITIES AT CGRA KOZHIKODE

Amount

SCHEDULE ‘A’ PART-I (BUILDING & STRUCTURE WORKS) Details of prepriced schedule is given in tender documents.

SCHEDULE "A" PART-II ( SITE CLEARENCE, EXCAVATION AND EARTH WORK ) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-III(INTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-IV (INTERNAL ELECTRIC SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-V (SEWAGE DISPOSAL) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VI (EXTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VII (EXTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART -VIII (MISCELLANIOUS ITEMS) Note:- This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col.' E ' signifies this fact only.

INTERNAL WATER SUPPLY S&F 15mm two way bib tap cast copper, chromium plated complete all as specified and directed.

S&F Chromium plated, brass health facucet with 1.2Mt flexible tube & wall hook complete all as specified and irected.

INTERNAL ELECTRIC SUPPLY S & F 20 W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed.Make: BAJAJ Cat-Part No. BCLAB 20W or equivalent in list of Approved make attached

S & F 10 W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: BAJAJ 112407 Cat-Part No. BCLSB 10W or equivalent in list of Approved make attached

S & F 20 W LED street light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 100 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting with bracket 1.5 m long with including necessary electrical connection to the fixture with 3 core flexible Copper conductor cable of appropriate size and light grade GI pipe,dia 20mm, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed. Make: BAJAJ Cat-Part No. BCLST 20W LED I or equivalent in list of Approved make attached

S & F 150W high bay light duranto mounted LED extruded aluminium housing with PC diffuser and integrated electronic driver with high effeciency long life LED chips CRI >80, power foctor >0.95 system luminious efficiency >100 having average life 50000Hrs, operating voltage 140 - 270, including electrical connection with 3 core flexible Copper conductor cable of appropriate size from ceiling rose to LED batten fitting complete all as specified and direcetd . Make: Havels Cat-Part No. RADIOSOHB150WLED75790DBOPC or equivalent in list of Approved make attached

S & F BEE five star rated energy efficient high-speed ceiling fan having 1200 mm blade sweep, air-flow not less than 210 CFM, operating voltage 220-240 V and frequency 50 Hz, including a downrod of suitable dia and length and electrical connection with 3 core flexible Copper conductor cable of appropriate size from ceiling rose to the fan complete all as specified and directed. Make: Crompton Cat-Part No. ENTRUST50 or Havells Cat- Part No. ES-50 or equivalent in list of Approved make attached

S&F enenrgy efficient high spped wall fan 400mm blade sweep smooth oscilattion and running, High speed motor for higher air delivery, operating voltage 220-240V and frequency 50Hz and electrical connection with 3 core flexible copper conductor cable of approproiate size from ceiling rose to the fan complete all as specified and directed. Make: Crompton Cat part No WM Fizzair 16"or equivalent in list of Approved make attached

S & F engery efficient non-metalic fresh air fan having blade sweep 250 mm, air delivery not less than 860 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and directed. Make: Crompton Cat-Part No. VENTILUS 10" or equivalent in list of Approved make attached

S & F engery efficient metalic exhaust fan having blade sweep 300 mm, air delivery not less than 900 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and directed. Make: Crompton Cat-Part No. TRANS AIR 12" or equivalent in list of Approved make attached

S & F MCB for AC applications conforming to IS/IEC 60898-1-2002, having breaking capacity Icn = 10 kA, sliding bottom clamp, colour coded on/off indication on dolly, biconnect IP 20 protected lower terminals and sliding shutters, etc. complete all as specified and directed by engineer-in-charge. 6 A, SP MCB, C- curve

16 A, SP MCB, C- curve

32 A, SP MCB, C- curve

32 A, DP MCB, C- curve

PILE FOUNDATION: Providing and erecting piling equipment/plant suitable for Cast in situ pile of 500mm dia (Complete with all accessories) erecting in position and removing after piling is completed all as specified and directed.

Boring of cast in situ pile of 500 mm dia to any depth through any type of soil/strata by DMC method using bentonite slurry including removal of bored materials to place out side MD land all as specified and directed.

Boring of cast in situ pile of 500 mm dia to any depth through hard rock by DMC method using bentonite slurry including removal of bored materials to place out side MD land all as specified and directed.

Reinforced cement concrete of grade M-30 design mix (RMC) as per IS-456 with using 20 mm graded stone aggregate in cast in situ bored pile of any length/any sections complete all as specified and as shown on drg as in bored pile including non destructive integrity test on all pile as per IS-2911 part-IV. (Note: The unit rate quoted under this item is deemed to be inclusive of charges for non destructive integrity test)

Reinforced cement concrete of grade M-30 design mix (RMC) as per IS-456 with using 20 mm graded stone aggregate in pile caps complete all as specified and as shown on drg (Note:- Reinforcement will be measured and paid for seperately under relavent items of this schedule)

Providing TMT bars (CRS/HCR/CRM) in reinforcement 10 mm dia and over for bored piles of any length and any dia all as shown on drgs including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and shown on drgs.

Providing TMT bars (CRS/HCR/CRM) in reinforcement 10 mm dia and over for pile caps all as shown on drgs including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and shown on drgs.

Providing TMT bars (CRS/HCR/CRM) in reinforcement 5 mm dia and over up to and including 10mm dia conforming to IS-1786 as stirrups for pile caps cut to length, bent to shape required, and binding with mild steel wire (annealed) not less than 0.9mm dia or welding

Providing TMT bars (CRS/HCR/CRM) in reinforcement 5 mm dia and over up to and including 10mm dia conforming to IS-1786 as Helical/stirrups for piles cut to length, bent to shape required, and binding with 0.9mm dia MS wire annealed or welding

PCC (1:4:8) type D2 using 40 mm graded stone aggregate for concrete layer below pile capsfoundation complete all as specified and directed.

Formwork to sides of pile caps rough finished surface of concrete flat. All as specified and as directed.

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M deep or area not exceeding 10 sqm on plan and getting out in soft/loose soil for pile caps

Returning filling in and ramming in layers around pile cap , plinth beams, tie beams etc using excavated soil including spreading levelling and well ramming in layers not exc 25 cm thick all as specified and as directed.

Removal excavated soil to distance not exceeding 50M and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and as directed.

Testing of piles (Initial Load test )for compression load, lateral load & uplift load) all as per IS 2911 including mobilising and removing the testing equipments from site after testing is completed all as specified and directed for 500mm dia cast in situ pile. Note: Rate inclusive for casting of 04 piles for above test. However concrete, steel and boring shall be measured under respective items

Testing of piles (Routine Load test) all as per IS for 500 mm dia cast in situ piles including mobilising and removing the testing equipments from site after testing is completed all as specified and directed.

EXTERNAL ELECTRIFICATION S&F of energy saving , enviromental friendly ,long life , exclusive innovative die-cast aluminiumn IP65LED flood light ,50W , suitable for highlighting architectural façade and general purpose lighting including all fittings and fixture all as specified and directed.

EXTERNAL Water Supply M & L for cutting the existing CPVC pipe of size 80mm dia and inserting CPVC connector of suitable size for taking branch connection all as specified and directed

M & L for earthing complete with galvanized steel earth plate electrode of 60 cm X 60 cm X 6 mm size, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized strip of size 32 mm X 6 mm as earth lead by means of bolts, nuts, checknuts and washers of galvanized iron or steel, galvanized iron pipe of 40 mm diameter connected to earthing test point, all as shown in electrical plate No. 5, connected to earthing test point including testing on completion, excavation, earthwork, PCC earth pit of dimensions 550 mm X 550 mm (outer) and 300 mm X 300 mm (inner) and 250 mm deep with a 10 mm deep CI cover hinged to CI frame on ground level, GI watering pipe, funnel, etc. all as specified and directed by engineer- in - charge.

VIJAY CONSTRUCTIONS

M/S V ASSOCIATES