WBMAD/NDITA/121/2025-26/SL.07

Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75m. In ground floor including roof. (a) upto 150 mm. thick

Taking out carefully Paver blocks from old footpath and stacking properly at suitable nearer site etc. all complete.

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. a) Pakur Variety

Providing and fixing at or near ground level precast cement concrete in kerbs (size: 410 mm x 310 mm x width 150 mm at bottom with circular nosing at top) (Nano kerb) of cement concreat M25 Grade without reinforcement, fixing as per approved pattern and setting in position at site after preparing the bed grade and slopes by laying Cement concrete with jhama khoa (1:4:8) as per specification and direction of Engineer-in-Charge including filling of joints with 10 mm thick cement morter (3:1) and back filling the vertical piece properly with earth duly compacted and curing the morter joints for atleast 3 days including cost and carriage of all materials complete.

Supplying, fitting and fixing M.S. rectangular/ square hollow bar based MS. grill Post (1.70 m. height) and projection all as per drawing duly jointed with continuous welding and nuts & bolts where required.

Supplying, fitting and fixing M.S. rectangular/ square hollow bar based MS. Grill (1.950m.x1.05m.=2.04 Sqm.) and projection all as per drawing duly jointed with continuous welding and nuts & bolts where required. Fabrication fitting, fixing including tack welding of M.S. sheet ( 2 mm. thick) indetification board complete.

Supplying and laying in the specified pattern of interlocking concrete block pavements(ICBP) with concrete blocks (with concrete grade as specified as per table 1 of IS 15658 : 2006) manufactured from BIS license manufacturer, with spacer nib (small protruding profiles on the vertical face of a paver block used as device for keeping minimum joint gap in between the paving blocks, as per Cl. No 3.26 of IS: 1568) and specified size and shape with aspect ratio the ratio of length t othickness of a paver block, as per cl.no.3.3 of IS: 15658) as per table 2 of IS: 1568 with flexural strength/breaking load as per annexure g of IS:1568, on the prepared base as certified CBR as per table 1 of IRC SP 63 2018 or else as of 25-35 mm thick (grading of the building sand as per clause 6.5.1 of IRC SP-63) paver block with joint filling sand and completing the edges with cut blocks as per CL.No. 8.7 of IRC SP-63(2018) with proper confinement of bedding and joint filling sand, compaction, levelling and filling up of the edge gap. 60 mm thick i) Colour Decerotive

Relaying &resetting interlocking paver block 60 mmof any shade and of approved quality over 75 mm thick medium sand as per IS:1237 -1980 laid in pattern as directed in pavement,Footpath,drive way etc. including necessary underlay complete in all respect with all labour and materials (Border concrete if necessary to be paid seperately)

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) B) Do - by fine sand

Applying One coat Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : On steel or other metal surface : Two coats (with any shade except white)

Add GST@18% on Sl. No. 1 to 17

Add labour cess @1% on Sl. No. 1 to 18