SPECIAL REPAIR TO 04 MD ACCN OF BLDG NO P 239 AT MIL STN GANDHINAGAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified& directed by Engr-in-Charge.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M & L brick work with old size sub-class ‘B’ bricks,(OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises

M&L for 16 to 18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and over 15mm thick screed bed in CM 1:6 complete all as specified& directed by Engr-in-Charge.

M&L for rounding to edges of stone/granite slabs one edge such as in steps cooking platform , window cill and other situations complete all as specified & directed

M&L for vetrified double charged ceramic tile 8 to 9mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.38sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L Glazed ceramic coloured tiles in vertical surface of area exc 0.16 sqm & 8 to 9mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified& directed by Engr-in-Charge.

M&L kota stone slab 10-15 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over rendering back of tile 10 mm CM 1:4 complete all as specified& directed by Engr-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

M&L for 25 thick cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in levelling coarse for tiles.

Material and labour vetrified double charged ceramic tile 8 to 9mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

Material and labour coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L machine cut kota stone slab flooring 20-25mm thick and area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over screed bed 15mm thick 1:6 cement mortar complete all as specified& directed by Engr-in-Charge.

M&L for 75 mm thick PCC 1:4:8 type D -2 using 40 mm graded stone aggregate as in sub base complete all as specified& directed by Engr-in-Charge.

M&L for Providing and laying prepolished cement concrete Chequered tiles 30cmx30cmx25mm thick, with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape heavy duty , set,jointed and pointed in neat cement slurry in floors over screed bed 15mm thick 1:6 cement mortar complete all as specified& directed by Engr-in-Charge.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand compelete all as specified and directed

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B.

Taking down chowkhats (without taking off shutters from the frames) chowkatts n exc 1.5 sqm each complete all as specified & directed by Engr-in-Charge.

Taking down chowkatts (without taking off shutters from the frames) chowkatts exc 1.5 sq. m but n exc 4 sq m each complete all as specified & directed by Engr-in-Charge.

Taking down shutter of any decription exc.1Sqm and n.Exc 2 Sqm complete all as specified & directed by Engr-in-Charge.

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions), slinding windows, rollers, with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F anodized aluminium grill with power coating (minimum thickness 50 micron) of approved pattern and fixed to the existing window/ventilator frame with CP brass/stainless steel scrwed @ 200mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement & directed by Engr-in-Charge.

S&F 4.8mm thick Sheet glass, ordinary quality and glazing with rubber bedding in square n exc 0.5 sq.m in each pane complete all as specified & directed by Engr-in-Charge.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floors/walls in PCC 1:2:4 type B-0 to match the existing floors/walls.

M&L for clamps , hold fasts; wall ties, plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts plate washers and similar small articles conforming to Fe-290 Gde-E-165 ® as directed by Engr-in-Charge.

S&F factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified and directed.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified and directed.

M&L for 25mm thick PVC Flush shutter, PVC solid core construction with PVC block board and off white/ brown/ off face panels, commercial type on both sided complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

M&L painting to new or previously untreated steel surfaces of any description over 10cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chromic primer including preparation of surfaces.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Supply and fixing stainless steel hinges 100mm long medium weight to pressed steel/angle iron frames by welding/screws all as specified.

S&F aluminium anodised barrel tower bolt 150mm size extruded section, ISI marked & fixed

S&F extruded aluminium alloy handles 150mm size fabricated type anodised. ISI marked.

S&F 300 mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, ISI marked complete all as specified.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

Taking down cement plaster any description on brick or stone any description

M&L Rendring 10mm thick on fair faces of brick work or concrete surfaces on walls, finished even and smooth without using extra cement in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L Rendring 5mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:4 finished even and smooth without using extra cement in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15mm thick in CM 1:4 on stone wall surfaces fair faces of brick work & finished even and smooth without using extra cement with water proof compound ( water proof compound paid seperatly) complete all as specified and directed.

M & L for internal/external plaster/unplastered newly/old surfaces on walls/ceilings and preparation of surfaces of walls/ceilings and plaster of paris putty of 1mm thick complete all as specified and directed by Engr-in -Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of Oil bound distemper complete all as specified & directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified.

Material and labour for preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of primer complete all as specified.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed

Material and labour for preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered/unplastered surfaces of ceilings & applying two coats of oil bound distemper (OBD) complete all as specified..

M&L for preparation of old surfaces of walls and applying one coat of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed.

M&L for preparation of old decorated surfaces of walls and applying two coat of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed.

M&L for preparation of old decorated plastered/unplastered surfaces of ceilings & applying one coats of oil bound distemper (OBD) complete all as specified..

M&L for preparation of old decorated surfaces of walls, plastered including cornices, pilasters etc and applying two coats of white wash complete all as specified.

M&L for preparation of old decorated plastered/unplastered surfaces of ceilings & applying one coats of white wash complete all as specified..

M&L for preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & as directed.

M & L for complete removal of existing treatment on walls/ceilings and preparation of surfaces of walls/ceilings and applying plaster of paris putty of 1mm thick complete all as specified and directed by Engr-in -Charge.

M&L preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified.

M&L preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified.

Taking up or down 15mm steel tubing and connections, complete all as specified& directed by Engr-in-Charge.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed by Engr-in-Charge.

Taking up or down 20mm steel tubing and connections, complete all as specified & directed by Engr-in-Charge.

S&F 20mm GI tubing Medium grade fix to wall/floor complete all as specified & directed by Engr-in-Charge.

Dismantling water tanks of capacity exc 250ltr but not exc 500ltr and removing from site complete all as specified & directed by Engr-in-Charge.

S&F Rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified & directed by Engr-in-Charge.

S&F in repair ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 15 mm dia complete all as specified & directed by Engr-in-Charge

S&F Sand cast,100 mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors and including dismentling old u/s pipes complete

S&F Sand cast,100 mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in wall and including dismentling old u/s pipes complete

S&F Sand cast,75 mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors and including dismentling old u/s pipes complete

S&F Sand cast,75 mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in wall and including dismentling old u/s pipes complete

S&F in repair CI Bends 100 mm dia (any radius),diminishing pieces or tapers (larger bore measured) complete all as specified

S&F in repair CI Bends 75 mm dia (any radius),diminishing pieces or tapers (larger bore measured) complete all as specified

S&F in repair 100mm Cast iron floor trap, with grating doom including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified

S&F in repair 75mm Cast iron floor trap, with grating doom including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified

S&F in repair 100mm dia Cast iron cowls complete all as specified.

S&F in repair 75mm dia Cast iron cowls complete all as specified.

S&F in repair 100mm dia pipe Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete

S&F in repair 75mm dia pipe Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete

S&F in repair for 150mm x150mm Salt-glazed stoneware gully traps, square or round mouthed, type 'P' including dismsntling old trap complete all as specified

S&F in repair fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed omplete all as specified & directed by Engr-in-Charge.

S&F in repair angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified & directed by Engr-in-Charge.

S/F in repair Vitreous China Squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rests connection to trap and to flushing pipe, etc.complete including making food to floor complete all as specified & directed by Engr-in-Charge.

Demolition of old existing unserviceable EWC seat and S&F vitreous china wash down water closet pan (Padestal pattern), white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repair PVC valveless, syphonic action type, flushing cistern of 10 ltrs capacity low level, white, with intel, ball valve, float and handle including brackets complete all as specified & directed by Engr-in-Charge.

S&F in repair brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F in repair brass chromium plated WHB mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore all as specified and as directed.

S&F in repair PVC connection of 15mm bore with 2 Nos. PTMT nuts, 60cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe all as directed by Engineer-in-charge.

S&F in repair Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore all as specified

S&F for 32mm dia Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges fixed to wall complete all as specified and directed.

S&F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete

S&F in repair kitchen sink with draining board made out of stainless steel 1mm thick with plugs, washers and waste pipe including bedding in cement mortarnd fixing cast iron cantilever brackets and connecting union to pipe over all size 495x420 mm bowl size 410x330x160 mm including flush pipe of polyethylene of low or high density or PVC 32mm bore with long screwed shanks and fly nuts complete all as specified & directed by Engr-in-Charge.

M&L for formwork to soffits of suspended slabs such as wash hand basin ,roof slabs, floor slabs, landings and similar work, not exc 200mm thick (horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 , using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Demolition Mud in roofs, any thicknes, including plastering , existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed by Engr-in-Charge.

M&L for providing cement concrete in type B0 1:2:4 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to (consolidated thickness 65mm or less) as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified& directed by Engr-in-Charge.

M&L screed laid 15mm thick in CM 1:4 as in roof over green concrete surface finished even and smooth using Lequid WPC complete all as specified. Note :-Lequid WPC will be measured and paid seperately)

Supply only integral liquid water proofing compound (ISI marked).

M&L for roof treatment using APP based polymeric membrane minimum weighing not less than 3kg/sqm black finish reinforced with non woven polyster matt with thermo finish (wt. not less than 150 gms/sqm) laid over compatible bitumen primer @0 .30 liters per sqm and bitumen 85/25 @ 1.20 Kg per Sqm with help of torching with a proplyne or a butane gas using torch with minimum overlap of 75mm at side and 100mm at ends and sealing including applying a coat of bitumen primer & bitumen 85/25 applied hot all as per manufacturer instructuions. For parapet in a groove (No separate payment will be made and measurement will be done for horizontal surfaces) including applying a coat of heat repallant bitumen aluminium paint @ 0 .1 liter per Sqm on topof treated surface of roof complete all as specified and directed.

S&F wall mixer chromium plated (2 in -1) with arrangement for overhead shower with 220 mm max long bend pipe including 125mm x125mm over head shower complete all as specified & directed.

S&F wall sink mixer chromium plated hot & cold arregement system and suitable screwed for iron pipes of 15mm bore GI pipe all as specified complete all as specified & directed.

S&F white vitreous china oval shaped wash hand basin of size 55cm X 40cm and including CP waste coupling complete all as directed by the Engr-in-charge.

S&F Jet spray chromium plated brass for EWC with & including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete.

S&F stainless steel Kitchen plate rack of overall minimum size 900mm x 900mm and 230mm deep, with partitions for small/large plates etc made out of stainless steel 24 Gauge, fixed with rawl plug and CP steel screws all as directed. Note : Weight of rack shall not be less than 6.00 Kg.

S&F 18mm thick, PVC sheet/board one side prelaminated of approved texture as in kitchen cabinet/cupboard ( with shelves and partions) including necessary fittings & fixture like auto closing concealed hinges, 75mm long fancy SS handle, magnet catch etc as per manufacturers instructions. Make ; Rajshree/Sintex

S&F 15x20x4 Inch stainless steel kitchen basket with stainless steel wire perforated plate fabricated and stainless steel heavy duty telescopic drawer/slide channel with wall bearing soundless complete

S&F 21x20x4 Inch stainless steel kitchen basket with stainless steel wire perforated plate fabricated and stainless steel heavy duty telescopic drawer/slide channel with wall bearing soundless complete

S&F stainless steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C complete all as specified and directed.

S&F Mirror Cabinet PVC frame of size 400x500mm fixed to wall with rawl plug & stainless steel suitable size scrweds complete all as specified and directed.

S&F for 300mm dia Corner Shelf complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls, plastered including cornices, pilasters etc and applying one coats of weather proof exterior emulsion paint complete all as specified.

Taking down carefully copper/aluminum point wiring (light, fan,socket or power) complete,including fixture and fitting such as as switches, ceiling roses, pendants, regulators, sockets,etc excluing light fittings etc,removing materials to store for keeping in safe custudy or for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surface of walls, ceiling, floor etc to match with the existing surface.

M&L for wiring with and including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in PVC Conduit concealed wiring and including medium grade PVC Conduit 20mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. complete all as specified and directed for the following :-

(a) One light/fan/Exhaust fan point controlled by one switch

(b) One multi purpose socket 5 Amps, Independent board.

(c) One multi purpose socket 5 Amps, on the same board.

(d) One bell buzzer point controlled by one push button independent.

(e) One light point controlled by two way switch

M&L for wiring with and including multi stranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number, drawing through in and including medium grade, rigid non metallic, PVC concealed conduit of 20mm bore and including cutting chases for conduits and sunken for boxes, its accessories & including with multi stranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, green colour, 1100 volts grade, ISI marked with valid CML number as continuity earth wire terminating with provision of sunken concealed terminal boxes complete all as specified and directed.

S&F in repair switch piano, flush button single pole, one way 5 Amps complete all as specified and directed.

S&F in repair socket outlet 2 in1, 3 pin, 5 Amps, flush type complete all as specified and directed.

S&F in repair socket outlet multipurpose, 3 pin, 5 &15 Amps flush type complete all as specified and directed.

S&F in repair switch piano flush button single pole, one way 15 Amps complete all as specified and directed.

S&F in repair switch piano, flush button single pole, two way 5 Amps complete all as specified and directed.

S&F in repair bell push,flush type, 5 amps complete all as specified and directed.

S&F in repair Ceiling rose, PVC/poly carbonate,isolated body three terminals,complete all as specified and directed

S&F in repair lamp holder, insulated body with back plate for batten fittings complete all as specified and directed.

S &F fix in repair Distribution Board SPN 8 way, 240 volts, factory made powder coated, double door with neutral and earth link, suitable for fixing MCB,s complete including connecting all as specified and directed.

S & F in repair MCB’s single pole, 6 to 32 Amps 240 volts with ‘C’ curve,10KA , fixed in sheet metal board complete including connecting.

S & F in MCB’s SPN 40 Amps 240 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

Supply and fixing in repair LED batten lights fitting 1x 20W, ultra slim square/round profile Led lighting fixture with polycarbonate,environmental friendly,energy efficient suitable size from ceiling rose complete.

S&F in repair LED light decorative ultra slim round/square profile LED lighting with extured polycarbonate enviromental friendly energy effecient ready to use pack 2 feet, 9 watt watt 220 V AC including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED 30 Watts (5700K) Bldg Security light fitting, and including with GI light grade Pipe 32 mm dia bracket with connected with 3 core flexible copper wire 0.50 Sq mm from ceiling rose after fixing fitting in position at site all as specified and directed. Make: Wipro /Philips /CG

M & L in replacement sub-main wiring with 2 single core 6 Sqmm PVC insulated, unsheathed, 1100Volts grade, copper multi stranded conductor drawn in PVC casing and capping ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 6.0 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire drawn through and connected to main switch/ DB and testing on completion. Note: (i). 2 run of main conductor and one run of earth conductor shall be measured as one length.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current Motor (BLDC)

S&F Exhaust fan steel body AC single phase.230V of size 300 mm sweep with bladeand frame and louvers Note 5 star rated , 300 mm sweep ,Suitable for 230 volt AC Supply 50 Hz with all accessories and mounting (Louver shutter, Frame Mounting Bolts , vibration pads etc) all as per specified and directed.

Supply and fix electric water heater,storage type steel body with Copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc.

Taking down existing Geyser and keeping in safe custudy and re- installation the same after completion of work completed all as per specified and directed.

Taking down existing Ceiling fan and keeping in safe custudy and re- installation the same after completion of work completed all as per specified and directed.

Supply, installation, testing & commissioning of 1 Phase ,2 wire Smart Prepaid energy Meters BIS 16444 Marked in existing Meter Board /Floor Panels with Pre Payment shock proof capacitive touch keypad ( Similar as IOS and android phone technology), bluethoot based Digital having current range 10-60 Amp 240Volt accuracy class 1.0 along with inbuilt load control switch containing provision of TOD & RTC inbuilt feature sense for data transfer (wireless without DCU ,USB Pen drive) no other extra equipment required for data transfer, meter itself capable for data transfer) capable to define 4 tariff slabs, happy hour & holiday definition, when user go outside of the home, via mobile app user can decrease its sanctioned load, user can punch recharge token on meter keypad and manually and automatic via mobile app meter shuuld support the following data's -30 minutes instantaneous data for voltage, current, power factor, power, cumulative energy and frequency, 30 load survey data for energy, monthly billing survey for cumulative energy and Max Demand. Meter should have connect /Disconnect remotely functionality operable for prepaid /post paid billing software. The meter should support communication protocol NB IOT /DLMS with the softwareall as specified and directed. That the manufacture or their service provider shall furnish 10 (Ten) years replacement guarentee for prepaid meters installed under this contract except damage from water and fire including 2 years vending charges and portel charges existing cloud base, complete all as specified and directed.

Supply, installation, commissoning and testing, factory made, LT Metal Box, wall mounted board made out of CRCA sheet of 2 mm thick indoor type totally enclosed weather, dust and vermin proof with front opening hinged door and locking arrangement mounted on MS flat iron (40x6 mm and 6" long) 04 No clamp welded to 40mm x 40mm x 5mm size angle iron frame alround panel body duly grouted on wall, 415 volts 3 phase, 4 wire AC 50 HZ having aluminium bus bar insulated with PVC sleeves, space for fixing single phase KWH electric meter of suitable capacity 04 Nos, copper lugs, spacers, mounting channels, rubber gasket, locking knobs, hylam sheet pieces, PVC shrinkable sleeves, nuts and bolts, washers etc and suitable size single core copper wire connections, suitable compartments and epoxy powder spray paint with primer complete all as specified including the following accessories including taking down old unserviceable distribution board, taking down and refixing serviceable electric KWH meter in new panel (all as per sample) complete comprising the followings :- (a) Incoming supply:- (i) MCCB, 415 Volts, 4 Pole, 25 KA breaking capacity of 63 Amps - 01 No. (ii) R-Y-B phase, LED indicating lamp - 03 Nos (iii) 200 Amp TPN main aluminium bus bar (b) Outgoing supply:- (i) MCB, SPN, 40 Amp, 10 KA = 04 Nos (ii) Space for mounting single phase energy meter - 04 Nos (iii) Copper cable 6 Sqmm wire and open terminals for all feeders.

Taking down existing Electric meter and keeping in safe custudy and re- installation the same after completion of work completed all as per specified and directed.

Aggarwal Brothers and company (BID ID -3131757)

Ramdev and Sons (BID ID -3130743)

Shree Builders (BID ID -3120324)

ALBA AC AND REF SERVICES (BID ID -3131522)