PROVISION OF GREASE TRAP, TOILET AND DRAINAGE FACILITY AT VARIOUS LOCATIONS AT AF STATION SAMANA.

Amount

Surface excavation n.exc 30cm deep and averaging 15cm deep and averaging 15 cm deep and getting out hard/dense soil complete all as directed by Engr-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil.

Returning filling any type of soil incl spreading, levelling, watering, and well ramming in layers complete all as specified and directed.

Removing excavated material of soils n. Exc 50 mtr and depositing where directed at a level n. Exc 1.50 m above the starting point complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 (using 40 mm graded aggregate) in foundations, filling and mass concrete complete.

M&L for providing precast cement concrete (1:5:8) (using 20mm graded stone aggregate ) solid building blocks exc 10 cm thick, in width (with plain or inter locking joints as directed) setting in CM 1:6 complete in wall or pillars all as specified and directed.

M& L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete

M&L for RCC nominal mix (1:2:4 type B1 using 20 mm graded aggregates) as in lintel beam, chhaja all as specified

S&F rough finished surfaces of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilvers, shelves including supports, overhanges etc also splays between floors and beams etc

S&F TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less then 0.9 mm dia or securing with clips complete all as specified and directed.

Ditto- all as per srl item no above but 6 to 8 mm dia. Bar for stirrups

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410 -W (Gde-E- 250) quality- A

S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L for rendering 15 mm thick in cement mortar 1:6 over PCC block masonry/concete wall surfaces, finished the surfaces even and smooth complete

M & L for rendering 15 mm thick in cement mortar 1:4 over PCC block masonry/concete wall surfaces, finished the surfaces even and smooth complete

M&L for Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of Distemper oil emulsion over one coat of primer, all as specified & directed.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 4mm thick tinted glass and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead, joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200mm size etc all as specified below and as directed by Engr-in-Charge. (a) Frame (top & side) section shall of size 101.60x44.75 X2.00 mm

(b) Vertical Memeber of shutter section shall be of size 85.00x44.4X2.00 mm (c) Top Memners of shutter section shall be of size 83.50x44.45mm (d) Lock rail (Middle member) of shutter section shall be of size 150.00x44.45 X2.00 mm (e) Bottom Member of shutter section shall be of size 150.00x44.45X 2.00 mm (f) Glazing clip for securing glass of shutters shall be of 0.80 mm thick

S&F aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) three track window ( two shutters glazed & one shutters wire gauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.20 mm

(b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.20 mm (c) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.20 mm (d) Shutter Interlock Section shall be be of size 18.00 x 40.00 x 1.20 mm (e) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.20 mm

S&F aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with aluminium section of size 63 mm x 38.00 mm x 1.17 mm thick , half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including M.S wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position complete.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F 75 mm long Butt hinges, medium weight, cold rolled mild steel, and fixed

S&F 100mm long Aluminium handles, cast type, anodised

S&F 100mm long Aluminium anodised, barrel tower bolts of extruded section and fixed

S&F Supplying and laying of CPVC pipes (outer dia 20mm) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete all as specified and directed

S&F 15mm dia Bib taps, cast copper alloy, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern) white with CI 'P' or 'S' trap incl water closet seat cover of plastic,jet etc.complete incl necessary PVC waste pipe fitting, complete all as specified and directed by Engineer-in-Charge

S&F PVC(SWR), floor trap, with grating outlet dia 75 mm, including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F PVC waste pipe flexible type suitable for couplings 32 / 40 mm dia and 750 mm long.

S&F 15 mm bore fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F 15 mm size angular Stop valves, cast copper alloy,fancy type, chromium plated , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete.

S&F 10 Litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets & PVC flush pipe, fixed in position and connecting complete.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm.

S&F health faucet with 1 meter long easy flex tube in chrome finish & wall hook, complete all as specified

S&F white vitreous china wash hand basin (Flat back) of size 580x450mm fixed on and including new brackets complete in, 32mm size brass chromium plated wastest coupling, 750mm long PVC waste pipe, PVC connection pipe, 15mm size and 450mm long with PTMT nuts and washer at both end etc complete all as specified and dired

S&F 500 ltrs capacity three layer, rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position over existing PCC platform incl all fitting such as connection pieces with GI tank nipple for inlet, outlet, etc complete all as specified and directed

S&F 25mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/20mm-210gms./ 25mm-455gms / 40mm - 690 gms) complete all as specified

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in Cement Plaster 1:4 on wall surfaces all as per specified and direcetd.

M&L for Glazed ceramic white tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match all as per specified and direcetd.

M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) in roof kerbs or mud stops, rounded or chamfered coping etc, complete all as specified

M&L for RCC 1:2:4 type B1 using 20 mm graded stone aggregates as in cover slab for soakage well / manhole and similar works supported on walls and set in cement mortar 1:4 complete. Note:- Reinforcement steel will be measured & paid separately

S&F 150mm dia reinforced concrete pipes, class NP2, laid and jointed in cement mortar 1:2 complete with collars as specified and directed

M&L for 150mm thick Concrete,type D-2 1:4:8(using 40mm graded aggregate) bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and directed.

M&L for PCC 1:2:4, type B2(using 40mm graded aggregate) as in surface channels and drains

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl forms, moulds, mitred/stopped ends

Material & Labour for point wiring for one light / Fan point controlled by one, one way switch complete with 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable 1100 volts grade ISI marked drawn and including PVC capping & casing not less than 25 mm wide, including all accessories like bend, tees, junction boxes etc. including 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable as a earth wire connected to common earth dolly, etc including PVC surface type terminal box of suitable size with PVC cover complete.

All as per item No 51 above but point wiring for one 5 Amps socket outlet on independent board controlled by one-way switch.

Material & Labour for sub main wiring with 2 run single core multistranded copper conductor cable, of size 4.0 Sqmm, PVC insulated, unsheathed, fire retardant, low smoke (FRLS) drawn through and including steel conduit not less than 25 mm wide with all necessary fitting and including one run single core multistranded copper conductor cable, of size 4 Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire, fixed on wall / ceiling complete. Note: 2 Runs of main cable and one run earth wire with capping & casing will be measured as one RM for payment.

S&F Switch socket combination white polycarbonate body, 6A- 230 V, 2/3 pin combined, including connecting complete.

S&F Switch Piano type, white polycarbonate body, single pole, one way 6 amp, 230 V, including connecting complete.

S&F Distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof SPN 8 way with 200 Amps rated copper bus bar neutral bar, earth bar IP 43 protection, single pole and neutral 240 volts, double door type,240 V fixed flush to wall complete all as specified and directed.

Supply and fix MCB’s single pole 6 to 32 Amps, 230 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

Supply and fix MCB’s single pole & neutral, 32 Amps, 230 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

S&F energy efficient LED tube light fitting with built in LED & integral LED driver 18 to 20 watt, channel housing & diffuser of length 1200 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

S&F energy efficient LED tube light fitting with built in LED & integral LED driver 8 to 10 watt, channel housing & diffuser of length 600 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

S&F in exhaust fan steel body AC single phase, 230 V single phase of size 300 mm sweep.

M&L for Ceiling rose, 3 terminal polycarbonate body 6 Amps, 250 volts AC, including connecting complete.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

S&F 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil.

M&L for 100mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) as in flooring complete all as directed.

M&L for cutting existing pipeline of bore 25mm,making thread at both end and fixing tee of equal size 25mmX25mmX25mm complete all as specified and directed.

Supply and fixing 25mm dia Tubes, ' medium grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors / trenches.

Supply & laying PVC underground cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 2 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc complete all as specified & directed

S&F Sheet moulding compound (SMC) junction box of size 280 mm x 170 mm x 130mm, comprising three phase aluminium bus bar and one No MCB SP, 06 Amps "C" type, fixed on pole with mild steel clamps, nuts and bolts complete.

M&L for providing dry river sand as in sand cushioning to under ground PVC cable including punning down of sand in layer all as specified and directed. (Note: Work shall be executed as per clause 19.75 of standard schedule of rates part-1 (2009) for measurement purpose thickness of sand after punning down will be considered.)

Supply & laying ISI marked & conforming to IS - 5820 - 1970 unreinforced precast concrete cable cover Class LV , Type I , flat size 250 mm X 150 mm X 40 mm in trenches as protection to LT UG cable all as specified and directed.

Supply and fixing 50mm dia Tubes, ' Light grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors/trenches/road crossing etc.complete all as per specified and directed.

Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C-2 (using 40 mm graded aggregate) in foundations, filling and mass concrete complete.

Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, all as specified and as directed.

M&L for Rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces and surface finished even and smooth without using extra cement.

M&L for preparation of newely plastered surfaces and applying two coats of cement based paint over one coat of alkali resistant primer etc on walls complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red-oxide, complete all as specified.

S&F 450 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars

S&F 100 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

S&F grease trap made of 2 mm thick stainless steel (304 grade) of size 1500 X 600X600 mm having flow rate 400 lit/min and volume 450 litres. Inlet and outlet shall be 100mm bore all as per manufacturer instructions and as per Sketch No. 1 in Particular Specifications.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers nexc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in Sub base complete all as directed.

M&L for 100 mm thick PCC 1:2:4 type B2 using 20 mm graded stone ggregate as in floor / hard standing, laid in alternate bay system, finish the urface fair & even and fair all as specified & directed.

M&L for Forming 12mm thick Expansion joints in concrete slab of having thickness 150 mm and joint filled with pre-formed bituminous filler and top 30mm primed andsealed with sealing compound, Grade 'A'

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'A'

M&L for Screed bed or bedding layer of motar 15mm thick for laying floor finishes in CM 1:6 complete all as specified and directed.

S&F PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints laid in trenches or in floors complete.

S&F 75mm bore of pipe PVC (SWR) bends of any radius/shoes fixed to PVC pipes provided with access door complete.

S&F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed on walls including clamps complete.

S&F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints laid in trenches or in floors complete.

S&F 110 mm bore of PVC(SWR) bends of any radius /shoes fixed to PVC pipes complete.

S&F 110mm bore of pipe PVC(SWR) junction single (Single T) equal or unequal fixed to PVC pipes complete.

S&F 110mm bore of pipe PVC vent Cowl fixed to PVC pipes complete.

S&F tubular tower rail 20mm dia D type 600mm long between flanges chromium plated complete.

Demolition of RCC of any description and in any position not otherwise specially provided complete(reinforcement cut as required to facilitate demolition)

ABR Trading Co