Construction of War Memorial Azadi Ki Pehli Ladai Ka Saheedi Samarak at Ambala Cantt in the Honour of Martyrs of the First war of Indias Independence, 1857 Ambala Cantt in Ambala District Art exhibits work including 3 yrs O and M

Amount

HSR [11.59]Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

HSR [11.8.1]12 mm cement plaster of mix : 1. 1:4 (1 cement: 4 coarse sand)

HSR [11.8.2]12 mm cement plaster of mix : 2. 1:6 (1 cement: 6 coarse sand)

HSR [13.30.1]Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 1. Hot finished welded type tubes

HSR [13.41]Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

HSR [20.71.1]Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge 1. 48" (1200mm)

HSR [20.72]Supplying, errection, testing of Exhaust fan (as per IS code 374) having a capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structure confirming to latest IS specifications complete in all respect to satisfaction of Engineer-in-charge.

HSR [21.100.3]Making holes for HCL soil / Waste pipe by core cutting up to 200 mm thick slabs and sealing with Drip seal sealant complete in all respect. 3. 125 mm dia pipe

HSR [21.100.4]Making holes for HCL soil / Waste pipe by core cutting up to 200 mm thick slabs and sealing with Drip seal sealant complete in all respect. 4. 150 mm dia pipe

HSR [21.100.5]Making holes for HCL soil / Waste pipe by core cutting up to 200 mm thick slabs and sealing with Drip seal sealant complete in all respect. 5. 175 mm dia pipe

HSR [23.1.6.1]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.1. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm)

HSR [23.1.6.10]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.10. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 3 run of Size 2.50 Sqmm(1.1.80mm)

HSR [23.1.6.2]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.2. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 1 run of Size 2.50 Sqmm(1.1.80mm)

HSR [23.1.6.3]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.3. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 1 run of Size 4 Sqmm(1/2.24mm)

HSR [23.1.6.4]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.4. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 1 run of Size 6 Sqmm(1/2.80mm)

HSR [23.1.6.5]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.5. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 1 run of Size 10 Sqmm(1/3.50 mm)

HSR [23.1.6.6]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.6. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 2 run of Size 1.50 Sqmm(1/1.40mm)

HSR [23.1.6.7]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.7. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 2 run of Size 2.50 Sqmm(1.1.80mm)

HSR [23.1.6.8]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.8. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 2 run of Size 4 Sqmm(1/2.24mm)

HSR [23.1.6.9]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.9. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 3 run of Size 1.50 Sqmm(1/1.40mm)

HSR [23.2.1.1]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 1.1. Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. Group A

HSR [23.2.1.2]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 1.2. Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. Group B

HSR [23.2.1.3]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 1.3. Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. Group C

HSR [23.2.2.1]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 2.1. Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. Group A

HSR [23.2.2.2]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 2.2. Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. Group B

HSR [23.2.2.3]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 2.3. Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. Group C

HSR [23.2.3.1]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 3.1. Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe, without separate control switch , Modular type Switch/sockets wiring Group A

HSR [23.2.3.2]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 3.2. Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe, without separate control switch , Modular type Switch/sockets wiring Group B

HSR [23.2.3.3]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 3.3. Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe, without separate control switch , Modular type Switch/sockets wiring Group C

HSR [23.2.4.1]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 4.1. Wiring in MS conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group A

HSR [23.2.4.2]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 4.2. Wiring in MS conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group B

HSR [23.2.4.3]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 4.3. Wiring in MS conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group C

HSR [23.2.5.1]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 5.1. Wiring in MS conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group A

HSR [23.2.5.2]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 5.2. Wiring in MS conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group B

HSR [23.2.5.3]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 5.3. Wiring in MS conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group C

HSR [23.22.1.10]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.10. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 125 to 160 amp, 25 KA

HSR [23.22.1.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.9. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA

HSR [23.22.2.2]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 2.2. MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings MCCB up to 250 A FP

HSR [23.22.3.2]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 3.2. Supply and erection of sheet steel enclosures 1pole/2 pole/4 pole on wall/on existing pedestal complete as required. S.P.N. or DP enclosure suitable for DP MCB

HSR [23.22.3.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 3.3. Supply and erection of sheet steel enclosures 1pole/2 pole/4 pole on wall/on existing pedestal complete as required. TPN enclosure suitable for TP , TPN or FP MCB

HSR [23.22.4.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.1. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 4 way ( 2 incoming and 2 outgoing)

HSR [23.22.4.10]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.10. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. Vertical TPN DB Double Door 6 way ( 8 incoming 3phase*6 outgoing)

HSR [23.22.4.11]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.11. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. Vertical TPN DB Double Door 8 way ( 8 incoming 3phase*8 outgoing)

HSR [23.22.4.12]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.12. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. Vertical TPN DB Double Door 12 way ( 8 incoming 3phase*12 outgoing)

HSR [23.22.4.2]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.2. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 8 way ( 2 incoming and 6 outgoing)

HSR [23.22.4.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.3. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 12 way ( 2 incoming and 10 outgoing)

HSR [23.22.4.4]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.4. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 16 way ( 2 incoming and 14 outgoing)

HSR [23.22.4.5]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.5. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing)

HSR [23.22.4.6]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.6. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 6 way ( 8 incoming 3phase*6 outgoing)

HSR [23.22.4.7]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.7. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 8 way ( 8 incoming 3phase*8 outgoing)

HSR [23.22.4.8]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.8. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 12 way ( 8 incoming 3phase*12 outgoing)

HSR [23.22.4.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.9. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. Vertical TPN DB Double Door 4 way ( 8 incoming and 3phase*4 outgoing)

HSR [23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole

HSR [23.22.5.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.3. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Double POLE

HSR [23.22.5.4]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.4. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. Double pole

HSR [23.22.5.7]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.7. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp MCBs FOUR POLE

HSR [23.22.5.8]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.8. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCBs FOUR POLE

HSR [23.22.6.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 6.1. Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. DP RCCB 30ma sensitivity , 25 A

HSR [23.22.6.2]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 6.2. Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. DP RCCB 30ma sensitivity , 40 A

HSR [23.22.6.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 6.3. Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. DP RCCB 30ma sensitivity , 63 A

HSR [23.22.6.4]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 6.4. Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TP RCCB 30ma sensitivity , 25 A

HSR [23.22.6.5]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 6.5. Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. FP RCCB 30ma sensitivity , 40 A

HSR [23.22.6.6]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 6.6. Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. FP RCCB 30ma sensitivity , 63 A

HSR [23.23.10]MISCELLANEOUS 10. Supplying and drawing of 1 no UTP 4 pair CAT 6a LAN Cable in the existing surface/recess MS/PVC conduit as required

HSR [23.23.6..2]MISCELLANEOUS 6..2. Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. MS perforated cable tray painted with powder coating 200 X 50 X 2 mm

HSR [23.23.6.1]MISCELLANEOUS 6.1. Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. MS perforated cable tray painted with powder coating 100 X 50 X 2 mm

HSR [23.23.6.3]MISCELLANEOUS 6.3. Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. MS perforated cable tray painted with powder coating 375 X 50 X 2 mm

HSR [23.23.6.4]MISCELLANEOUS 6.4. Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. MS perforated cable tray painted with powder coating 600 X 50 X 2 mm

HSR [23.6.6.2]MS CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of MS conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. MS pipe of 25 mm dia.

HSR [23.7.6.1]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.1. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 20 mm dia.

HSR [23.7.6.2]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia.

HSR [23.7.6.3]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.3. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 32 mm dia.

HSR [23.7.6.4]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.4. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 40 mm dia.

HSR [23.8.11.11]FITTING AND ACCESSORIES 11.11. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type

HSR [23.8.4]FITTING AND ACCESSORIES 4. Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm long M.S. Road made into suitable suspension hook and erected in R.C.C. slab for the erection of fan complete with all labour and material required to complete the job.

HSR [24.1.10]EARTHING AND LIGHTENING ARRESTOR 10. Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material.

HSR [24.1.13]EARTHING AND LIGHTENING ARRESTOR 13. Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as required.

HSR [24.1.14]EARTHING AND LIGHTENING ARRESTOR 14. Supply and erection of 20mm x 3 mm thick GI, tape fixed with suitable G.I. staples of same size.

HSR [24.1.16]EARTHING AND LIGHTENING ARRESTOR 16. Supply and erection of 25mm dia 1.5 metre long lightning GI. tube rod tapered into a point at the top with 16cm x 16cm x 3mm thick G.I. base plate and necessary nuts and bolts with washers.

HSR [24.1.17]EARTHING AND LIGHTENING ARRESTOR 17. Providing and fixing testing joints made of 20mm x 3mm thick G.I. strips 125 mm long with 4 nos. G.I. bolts and nuts with washers complete.

HSR [24.1.3]EARTHING AND LIGHTENING ARRESTOR 3. Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required.

HSR [24.1.4]EARTHING AND LIGHTENING ARRESTOR 4. Earthing with tinned copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required.

HSR [24.1.5]EARTHING AND LIGHTENING ARRESTOR 5. Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode.

HSR [24.1.8]EARTHING AND LIGHTENING ARRESTOR 8. Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material.

HSR [24.2.6.3]LT CABLE 6.3. Supply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work. 4 sqmm

HSR [24.2.6.4]LT CABLE 6.4. Supply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work. 6 sqmm

HSR [24.2.6.5]LT CABLE 6.5. Supply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work. 10 sqmm

HSR [24.2.6.6]LT CABLE 6.6. Supply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work. 16 sqmm

HSR [24.2.7.1]LT CABLE 7.1. Supply and erection of suitable compression type brass cable glands for underground Cable :- Up to 6 Sq mm cable 2 to 4 Core

HSR [24.2.7.2]LT CABLE 7.2. Supply and erection of suitable compression type brass cable glands for underground Cable :- 10 sqmm to 16 sqmm Cable 2 to 4 Core

HSR [24.2.7.3]LT CABLE 7.3. Supply and erection of suitable compression type brass cable glands for underground Cable :- 25 sqmm to 50 sqmm Cable 2 to 4 Core

HSR [24.2.7.4]LT CABLE 7.4. Supply and erection of suitable compression type brass cable glands for underground Cable :- 70 sqmm to 95 sqmm Cable 3 to 3½ Core

HSR [24.2.7.5]LT CABLE 7.5. Supply and erection of suitable compression type brass cable glands for underground Cable :- 120 sqmm to 185 sqmm Cable 3 to 32 Core

HSR [24.2.7.6]LT CABLE 7.6. Supply and erection of suitable compression type brass cable glands for underground Cable :- 240 sqmm to Cable 3 to 32 Core

HSR [24.2.7.7]LT CABLE 7.7. Supply and erection of suitable compression type brass cable glands for underground Cable :- 300 sqmm to 400 sqmm Cable 3 to 3½ Core

HSR [24.2.8.10]LT CABLE 8.10. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 120 sqmm

HSR [24.2.8.11]LT CABLE 8.11. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 150 sqmm

HSR [24.2.8.12]LT CABLE 8.12. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 185 sqmm

HSR [24.2.8.13]LT CABLE 8.13. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 240 sqmm

HSR [24.2.8.14]LT CABLE 8.14. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work.300 sqmm

HSR [24.2.8.15]LT CABLE 8.15. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 400 sqmm

HSR [24.2.8.5]LT CABLE 8.5. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 25 sqmm

HSR [24.2.8.6]LT CABLE 8.6. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 35 sqmm

HSR [24.2.8.7]LT CABLE 8.7. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 50 sqmm

HSR [24.2.8.8]LT CABLE 8.8. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 70 sqmm

HSR [24.2.8.9]LT CABLE 8.9. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 95 sqmm

HSR [24.5.2.1]MISCELLANEOUS ITEMS 2.1. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 40/32 mm outer dia/ inner dia

HSR [24.5.2.2]MISCELLANEOUS ITEMS 2.2. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 50/40 mm outer dia/ inner dia

HSR [24.5.2.3]MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia

HSR [24.5.2.4]MISCELLANEOUS ITEMS 2.4. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 90/75 mm outer dia/inner dia

HSR [24.5.2.5]MISCELLANEOUS ITEMS 2.5. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 120/105 mm outer dia/ inner dia

HSR [24.5.2.6]MISCELLANEOUS ITEMS 2.6. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 145/123 mm outer dia/ inner dia

HSR [24.5.2.7]MISCELLANEOUS ITEMS 2.7. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 180/150 mm outer dia/ inner dia

HSR [5.1.1]Dismantling dressed stone work ashlar face stone work, marble work or precast concrete work manually/ by mechanical means including stacking of serviceable and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : 1. In lime mortar

HSR [5.1.2]Dismantling dressed stone work ashlar face stone work, marble work or precast concrete work manually/ by mechanical means including stacking of serviceable and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : 2. In cement mortar

HSR [5.23.1]Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 1. Nominal concrete 1:1.5:3 or richer mix (i/c equivalent design mix)

HSR [5.23.2]Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 2. Nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix)

HSR [5.26]Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars.

HSR [5.7.1]Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 1. In mud mortar

HSR [6.22.1.1]Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. 1.1. All works above plinth and up to floor IV level : M-20 grade plain cement concrete (cement content considered @ 300 kg/cum)

HSR [6.22.1.2]Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. 1.2. All works above plinth and up to floor IV level : M-15 grade plain cement concrete (cement content considered @ 240 kg/cum)

HSR [6.22.1.3]Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. 1.3. All works above plinth and up to floor IV level : M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

HSR [7.21.1]Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: 1. Cement mortar 1:4 (1 cement : 4 coarse sand)

HSR [7.22.1]Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 1. Cement mortar 1:4 (1 cement : 4 coarse sand)

NS Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required. : 150 mm width X 50 mm depth X 1.6 mm thickness

NS Brick Flooring - Providing and laying flooring of Lakhori brick of approved artwork in customised size and laying pattern according to design scheme as indicated on drawings or as approved by the museum design consultant. The screed mortar to be spread and setting bed mixture 13 mm to 25 mm (1/2 inch to 1 inch) thick and true to plane. The bricks should not have chips, cracks, discoloration or other visible defects. Limit setting bed area so brick is installed before initial set. Wet brick according to the norms and bye laws and appropriate rate of absorption test. Apply 1 mm (1/32 inch) layer of neat cement paste over setting bed. Each brick to be Set and levelled immediately. Tamp brick to completely contact setting bed. Maintain uniform, aligned joints // 10 mm (3/8- inch) // 13 mm (1/2 inch) // wide or as specified by the museum design consultant. Joints to be grouted upon mortar bed initial set. Placing grout in joints, strike flush and tool slightly concave. Curing of grout by maintaining damp condition for seven days. The flooring to be complete with the cleaning, sealing and protetion process. (AOR No.RA-01)

NS Gravel Flooring - Providing and laying of customised gravels/ stone aggregate as approved by the museum design consultants on the desired locations inside/outside of the buildings mentioned as per the approved drawings to match the approved design scheme. It shall consist of naturally occurring (uncrushed, crushed or broken) river bed shingle or pit gravel. It shall be sound, hard and clean. It shall be free from flat particles of shale or similar laminated material, powdered clay, silt, loam, adherent coating, alkali, vegetable matter and other deleterious substances. Pit gravel shall be washed if it contains soil materials adhering to it. These shall conform to IS 383 unless otherwise specified. (AOR No.RA-02)

NS Mud flooring - Providing and laying of 10mm - 12mm Thk. Mud plaster with 5% cememnt mixed with local mud and chopped and sifted straw laid in a single unjointed layer rammed thoroughly upto a desired thickness. The finish layer applied to be a mixture of cow dung and clay with a thickness of min 1mm on with rapid curing on existing false floor similar to ground surface of excavation sites found in haryana, with MS wire mesh gauge as per area demarked on drawing , as per approval by museum design consultant. (AOR No.RA-03)

NS False Flooring - 150mm - Providing and Fixing of False floor with MS tubular section of 50mmX50mm/75mmX75mm/as per requirement of desired thickness with appropriate spacing and necessary welding at junctions including application of 25mm to 32mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to base with 2mm thk MS plate of desired size and base properly welded with all fasteners and necessary hardware's with edge profiles, beadings etc all complete as per approved design. The rate is also inclusive of two coats of MS primer on the frame structure and one to two coats of anti termite oil finish on ply board. Height of False flooring to be considered is 150mm alongwith provision of cove as per design requirement. (AOR No.RA-05)

NS T Profile for edging of Flooring - Providing and fixing carpet edge Aluminium T profile with adhesive on the joints. Size 25mm , up to 50mm.

NS Reflective tape Roll - Providing and fixing of reflective tapes on concerened areas demarcated in drawings.

NS Ply Finish (6mm, 12mm, 18mm) - Two or more coats of french polish on new works including a coat of wood filler

NS SITC of T Joint suitable for above track items. (AOR No.RA-07)

NS IPS flooring - Providing and laying of 75mm thick IPS flooring with artwork/design as required of approved make and pattern. The cost is inclusive of providing an under layer of concrete of 63mm thickness with a mix of CC 1:2:4 (1 part cement, 2 parts coarse sand and 4 parts graded stone aggregate-12.5 mm and downgraded). The top layer to be 12mm thick. The flooring shall be laid in panels of uniform sizes of 2 SqM or as approved by the Museum Design Consultant.The surface of the RCC slab shall be roughened up with brushes while the concrete is green. Before laying the floor, the laitance, loose materials, cake of mortar dropping shall be removed and the surface of the slab hacked and coat of cement slurry @2.75 kg of cement per Sqm shall be applied so as to get a good bond between the slab and IPS. If IPS has to be provided on lean concrete no slurry is required. The top finish coating to be as per approved by the Museum Design Consultant. Make: Bharat flooring or equivalent (AOR No.RA-04)

NS False Flooring - Upto 600mm - Providing and Fixing of False floor with MS tubular section of 50mmX50mm/75mmX75mm/as per requirement of desired thickness with appropriate spacing and necessary welding at junctions including application of 25mm to 32mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to base with 2mm thk MS plate of desired size and base properly welded with all fasteners and necessary hardware's with edge profiles, beadings etc all complete as per approved design. The rate is also inclusive of two coats of MS primer on the frame structure and one to two coats of anti termite oil finish on ply board. Height of False flooring to be considered is 600mm alongwith provision of cove as per design requirement. (AOR No.RA-06)

NS Micro-topping flooring - Providing and laying micro-topping flooring system composed of polymer (not water) mixed with special cement admixture of desired shade, texture and approved make as per the direction of museum design consultant. The rate to be inclusive of preparing a sub base free of dust, laitance, oils or any loose material with a provision of any expansion, contraction and crack inducing joints to avoid cracking, unevenness and faults, including application of Epoxy-coat mixed with 20% quartz-sand (0,2-0,5mm) as adhesion primer and covering thoroughly the surface with quartz-sand on substrate. Rate includes the application of two coats of base coat with 0.5mm coarse sand used as gauge evenly spread upto maximum thickness of 0.5mm. Followed by application of upto two coats of very thin layer of finish coat or high-performance coat without coarse sand for smooth appearance. The final coat is to be sealed with acrylic or PU sealer all complete as per the direction of engineer incharge. Approved make : Bharat Flooring/idealworks/eqv (AOR No.RA-07)

NS Vinyl Flooring - Providing and fixing of foam backing vinyl flooring of thickness 1mm to 2mm of approved shade and quality with anti skid, excellent sound insulation, shock absorbent, ease of maintenance. The cost is inclusive of preparing a even layer of sub floor of thickness upto 2mm with polymer based self levelling compound of desired colour to achieve a total thickness of 3mm to 3.2mm as approved by museum design consultant , as per the area demarcated in the drawing and as approved by museum design consultant. Make : Euronics, gerflor, jeoflor, alphtahs, eqv (AOR No.RA-08)

NS Metal Flooring - Providing and fixing of Matt rustic finished SS/MS Metal Floor Panels customised to desired colour and texture by the museum design consultant for a raised floor of varying heights. Flooring composition : Perforated panel ,stringer,pedestal and screws. Thickness- as per structural stability and as desired by the museum consultant. Make :(Armstrong, Euronics, Geggus, alphtahs or eqv) (AOR No.RA-09)

NS Carpet Flooring - Providing & Laying approved shade of acid stain resistant Carpet Tiles/flooring of 2-5 mm thickness with waterproof backing , installed in area demarked in detail drawings over vertical/horrizontal surface and as per company specifications. Thecost is inclusive of necessary adhesives, fixtures, profiles etc all complete as per the direction of Engineer in charge. Make :(Armstrong, Euronics, Geggus, alphtahs or eqv) (AOR No.RA-10)

NS Jute Carpet Flooring - Providing and fixing carpet flooring made of jute hand-woven/braided by the special artist/craftsmen of desired size and thickness in the pattern and shade as per the approval of the design consultant. The carpet to be anti skid, excellent sound insulation,ease to maintain. The rate is inclusive of laying an underlay wherever required and fixing in place with necessary foam backing heavy duty adhesives, doble sided carpet tapes etc all complete as per the direction of engineer in charge. (AOR No.RA-11)

NS Metal Carpet Flooring - Providing & Laying approved shade of stain resistant Metal Carpet Tiles/flooring of 4-5 mm thickness with waterproof backing , installed as per detail drawings and as per company specifications with the approval of museum design consultant. Make Euronic / Gerflor/ Jeoflor/ alphtahs/ equivalent. (AOR No.RA-12)

NS Specialized rubberised flooring - Providing and laying of kids friendly flooring which are safe, hygienic, durable, soft, anti skid, excellent sound insulation, shock absorbent, abrasion resistant, such as rubberized flooring, cork, epdm rubber etc with thickness . The floorings to be laid in pattern and levels as per deisgn. Make Euronic / Gerflor/ Jeoflor/ alphtahs/ equivalent. (AOR No.RA-13)

NS Red sandstone - Providing and laying of red sandstone flooring with custom artwork in varying sized of 300x300mm, 600x300mm, 600x1200mm of approved shade, set in pattern as given by the architect, over thick base of lime surkhi mortar including jointing finished flush with lime putty and stone powder filling joints with neat cement slurry, curing, polishing and cleaning etc.complete as per the approval of museumvdesign consultant. (AOR No.RA-14)

NS Aluminium Corner Guard - Providing and fixing of Aluminium corner guard made in anodized aluminium of approved shade of size 25mmX25mm and desired thickness. The cost is inclusive of fixing the wings at the edge for excellent finish with heavy duty adhesives on each wing in zig zig pattern for a sleek and stylish appearance. The cost includes drilling for making holes for rawl plugs, screws etc wherever required all complete as per the satisfaction of museum consultant. Make : Euronics, gerflor, jeoflor, alphtahs, eqv

NS Wooden FloorinG - Providing and installing of 8mm - 10mm Thk. Wodd finish on floor similar to ground surface of excavation sites with required hardware and base finish also having the foom beneth and plastic packed , as per approval by museum design consultant. (False floor cost not to be included) Make :(Armstrong, Euronics, Geggus, alphtahs or eqv) (AOR No.RA-15)

NS Printed Vinyl Flooring - Providing and Fixing of Foam Backing Customized printed Vinyl flooring with anti skid, excellent sound insulation, shock absorbent, ease of maintenance with self levelling compound of Gray colour with thickness of 3 - 3.25 mm , as approved by museum design consultant. Make :(Armstrong, Euronics, Geggus, alphtahs or eqv)

NS Designer artwork concrete flooring - Providing & fixing of Concrete artwork panel in vertical dry/wet cladding 10-35 mm thick panel and size as per detail design in required position on ms clamp and complete and loading, unloading, transportation and including all other taxes and excluding GST complete as directed by Engineer In charge.Artwork as /graphics and to be approved by museum design consultant.

NS Free standing Wooden Partition curved- 150mm - Providing and fixing 150 mm overall thickness free standing partition up to 4 meter height consisting of 50X50mm/75X75mm/ as per site requirement wooden battens in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions with screws, nails, adhesives and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The rate to be inclusive of providing and installing top cover of 12mm to 18 mm Flexible ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws, nails etc all complete as per approved drawings and the direction of engineer in charge. The cost is also to be inclusive of providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. The surface should be smooth enough for vinyl film application.

NS Wooden Fluted louver panelling - Supply and installation of wooden fluted louvers on walls of size as approved by the museum design consultant. The panels to be complete all the hardware/ equipments required for the mounting. The cost to exclude the cost of the base partition/wall. The finish of the panels to be as approved by teh musuem design consultant.

NS Specialized kids wall panelling - Providing and fixing of kids friendly wall panelling uplohatered with fabric, kids safe leatherite, or similar as per design The paneling should safe, hygienic, durable and soft. The panelling to have the provision for cut-outs, peekholes, etc. on walls. The cost of base panelling to be excluded.

NS Wall mount paneling with wooden frame work 150 - Providing and fixing of 150 mm thick mounted paneling with minimum 50X50mm/75 x 75 mm wooden batten in a grid pattern at 600 mm c/c both ways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions with screws, nails, adhesives etc all complete. The cost to be inclusive of top cover of 12 mm commercial plywood BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc. The wooden section to be coated with one to two required coats of anti termite solvent and wooden battens used should be good quality wood. The cost is inclusive of fixing the wooden frame structure on floor/wall/ ceiling with necessary adhesives, hardwares, fastners, fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete as per approved design. The cost includes scrapping and levelling the surface for the application of two or more coats of primer to prepare a smooth base for the application of media as per the satisfaction of engineer in charge.

NS Free standing MS Partition - 150mm - Providing and fixing 150 mm overall thickness free standing partition up to 4 meter height consisting of ms hollow section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm flexible ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The cost is also to be inclusive of providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. The surface should be smooth enough for vinyl film application.

NS Pinewood Panelling - Providing and fixing of pinewood panelling with 12mm thick matte finish Solid Pine Panels with Grooving of approved color and quality of size approx 12mm X85mm X 1200mm. The cost is inclusive of installing the panels on base of 12mm thk commercial Plywood/board of approved make or 12mm wood runner / Tongue & Groove forming a framework of desired size to be installed on the wall. The cost includes necessary hardwares, fixtures, screws, nails, adhesives etc all complete

NS Free standing Curved MS Partition - 150mm (ply on both Sides) - Providing and fixing 150 mm overall thickness free standing partition up to 4 meter height consisting of ms hollow section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The cost is also to be inclusive of providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. The surface should be smooth enough for vinyl film application.

NS Free standing Curved MS Partition - 300mm (ply on both Sides) - Providing and fixing 300 mm overall thickness free standing partition up to 4 meter height consisting of ms hollow section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm flexible ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The cost is also to be inclusive of providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. The surface should be smooth enough for vinyl film application.

NS Free standing Wooden Partition - 150mm - Providing and fixing 150 mm overall thickness free standing partition up to 4 meter height consisting of 50X50mm/75X75mm/ as per site requirement wooden battens in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions with screws, nails, adhesives and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The rate to be inclusive of providing and installing top cover of 12mm to 18 mm ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides with edge profiles, including the cost of necessary hardware, screws, nails etc all complete as per approved drawings and the direction of engineer in charge. The cost is also to be inclusive of providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. The surface should be smooth enough for vinyl film application.

NS Wall mount paneling with wooden frame work 75 - Providing and fixing of 75 mm thick mounted paneling with minimum 50X50mm/75 x 75 mm wooden batten in a grid pattern at 600 mm c/c both ways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions with screws, nails, adhesives etc all complete. The cost to be inclusive of top cover of 12 mm commercial plywood BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc. The wooden section to be coated with one to two required coats of anti termite solvent and wooden battens used should be good quality wood. The cost is inclusive of fixing the wooden frame structure on floor/wall/ ceiling with necessary adhesives, hardwares, fastners, fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete as per approved design. The cost includes scrapping and levelling the surface for the application of two or more coats of primer to prepare a smooth base for the application of media as per the satisfaction of engineer in charge.

NS Magnetic laminate panelling - Providing and fixing laminate with holding capacity of holding magnet, having thickness of upto 1.5mm. The color and finish of the laminate to be approved by the museum design consultant.

NS Bamboo/ Sarkanda panelling - Providing and fixing of panelling in Sarkanda/ jute/bamboo/ wheat stalk with artwork in the pattern as suggested by the craftsmen and approved by the museum design consultants. The sarkanda/jute panelling to be done by the special artists/ expert craftsmen of Haryana under supervision of the museum design consultants.The panelling to be fixed with base using nails, adhesives, and all necessary accessories required to make it functional.

NS Freestanding Bamboo/ Sarkanda partition - Providing and fixing of freestanding curved partition in Sarkanda/ jute/bamboo/ wheat stalk with artwork in the pattern as suggested by the craftsmen and approved by the museum design consultants. The sarkanda/jute panelling to be done by the special artists/ expert craftsmen of Haryana under supervision of the museum design consultants.The partition to be fixed on floor/ceiling with metal rails, approved hardware and all necessary accessories required to make it functional.

NS Black lacquered Glass panelling - Providing and fixing of 6mm to 12mm thk toughened glass with highly resistant lacquer to one side of the glass of approved make and shade as per colour in specified in detail drawings and as approved by consultant. The rate is inclusive of fixing properly with all necessary silicone adhesives, fittings, arrangement and making necessary holes wherever required etc. all complete as per direction of Engineer in charge.

NS Mirror paneling - Providing and fixing mirror finish wooden panelling with base frame made up of wooden battens 50mmX50mm to 75mmX75mm as per site requirement placed at 600mm c/c both ways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions with screws, nails, adhesives etc all complete. The cost to be inclusive of top cover of 12 mm commercial plywood BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc. The wooden section to be coated with one to two required coats of anti termite solvent and wooden battens used should be good quality wood. The cost is inclusive of fixing the wooden frame structure on floor/wall/ ceiling with necessary adhesives, hardwares, fastners, fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete as per approved design including the cost of front cover of 2-6 mm thk. mirror of size as per design and as per specs/approval of the museum design consultant ,the panel cost to include all the necessary hardware for fixture

NS Pivot Lacquered glass panel - Providing and fixing of 12mm thk toughened glass with highly resistant lacquer to one side of the glass of approved make and shade as per colour in specified in detail drawings and as approved by consultant. The rate is inclusive of fixing properly with all necessary silicone adhesives, fittings, arrangement and making necessary holes wherever required etc. all complete as per direction of Engineer in charge. The rate is inclusive providing MS frame/box section of desired size. The panel to include all the necessary hardware/accessories required for a pivot opening panel. The cost is also to be inclusive of providing a finish surface of powder coating/duco/steel primer of approved shade etc on the ms section. Panel size: 2000x2500mm

NS Glass Partition - Supply and installation of 12 mm thk clear toughened Glass of approved make and desired size in aluminium glazing profile/ U section of desired size fixed to the ceiling and floor with necessary screws, hardwares, fixtures etc all complete. The cost is also inclusive of installing the glass panel to the aluminium section with extra clear silicone adhesives in the Museum as per the satisfaction of engineer in charge (AOR No.RA-16)

NS Backlit Glass panelling - Designing, Providing and Installation of 12mm thk toughened glass Info - Graphic glass panel of size 1200mm x 4500mm, mounted on on museum interior walls fixed on the wooden batten frame of section 100mmX50mm at 600mm c/c both ways and 12mm thick BWR grade plywood of Greenply/Century ply or similar makes on front side with all the necessary hardware's used to fix the Canvas , inclusive of custom designed Printed text and graphics Printed text and graphics as per requirement of the gallery design and conceptual design given by museum design consultant. The Glass panel has to be backlit, with appropriate acrylic backing and LED light fixture with drivers and all necessary hardware. The Backlit boxing should be able to diffuse sharp LED glare from light fixtures. Content and panel design needs to be approved by museum consultant before production. All prints will be done 1/32” - 1/8” from the edge of the glass to prevent contamination and consequential defects resulting from overspray. Choose high quality image from reliable source (min. 2500 pixels) for the best results • Check quality in Photoshop at 100% scale (proportionate to actual size desired) • Consider the viewing distance for the graphics • Complete print test (scale to final size, print small crop, apply patterns, view at actual distance, adjust) • Request a Sample Print from vendor if unsure of the expected results • Image quality impacts final image result: Image resolution is pixel data image holds, therefore the higher the resolution, the more detail the image will have. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English, , as per conceptual design provided by Museum consultant.

NS Sliding Wooden curved Partition - 75mm - Providing and fixing 75 mm overall thickness curved sliding/openable partition up to ceiling height (up to 6 meters)consisting of G.I./ms frame with top cover of HDWR / HDMR conforming to BWR grade on both side with edge profiles, including providing and fixing of frame work made of special section, formaldehyde free, fire retardant. Make Sipla/ UP Twiga/ Orwens Corning / - Installed with MS wire mesh. Installation complete with all necessary Hardware. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical,sliding rails,remort control or any other mechanism required to make it functional. the automated opening mechanism should seamless in visual and audio should be synced with the AV content played in the insallation for opening and closing.

NS Projector-2 9600 lumens - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Make- Christie,Barco,NEC, Digital Projection

NS Display - 65" - Supplying and installation LED TV with minimum bezel - 65" .Dynamic Crystal Color with Quantum Processor 4K for incredible picture quality,Resolution 3840x2160(16:9),Pixel Pitch(mm) :0.372 x 0.372,Brightness : 700 nits,Contrast Ratio : 4000:1,Color Gamut : 92% (DCI-P3, CIE 1976),Haze Non-Glare, Processor Cortex A72 1.7GHz Quad-Core CPU. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Make-Christie,Samsung/LG/Panasonic/Delta

NS Printed Glass (for wall panelling) - Providing and Installation of 12mm thk toughened glass, printed with large-format ceramic ink digital print technology . All prints will be done 3-5 mm from the edge of the glass to prevent contamination and consequential defects resulting from overspray. Choose high quality image from reliable source (min. 2500 pixels) for the best results. (Note :- Rate exclusive of partition) • Check quality in Photoshop at 100% scale (proportionate to actual size desired) • Consider the viewing distance for the project • Complete print test (scale to final size, print small crop, apply patterns, view at actual distance, adjust) • Request a Sample Print from vendor if unsure of the expected results • Image quality impacts final image result: Image resolution is pixel data image holds, therefore the higher the resolution, the more detail the image will have. as per approval by Museum Design Consultant. This quantity is inclusive of printed glass and is considered for wall panelling on various surfaces.

NS Micro topping finish on walls - Providing and fixing micro- topping wall system composed of polymer (not water) mixed with special cement admixture of desired shade, texture and approved make as per the direction of museum design consultant. The rate to be inclusive of preparing a sub base free of dust, laitance, oils or any loose material with a provision of any expansion, contraction and crack inducing joints to avoid cracking, unevenness and faults, including application of Epoxy-coat mixed with 20% quartz-sand (0,2-0,5mm) as adhesion primer and covering thoroughly the surface with quartz-sand on substrate. Rate includes the application of two coats of base coat with 0.5mm coarse sand used as gauge evenly spread upto maximum thickness of 0.5mm. Followed by application of upto two coats of very thin layer of finish coat or high-performance coat without coarse sand for smooth appearance. The final coat is to be sealed with acrylic or PU sealer all complete as per the direction of engineer incharge. Approved make : Bharat Flooring/idealworks/eqv

NS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Make- Dataton/Coolux/Pixera/Vioso Equivalent

NS interactive sensor projections- well - The visitor will be given a fabric lotus petal which itself is a symbol of the freedom struggle and which will be incorporated with a RFID or NFC interaction element. The visitors will hold a this interaction enabled lotus petal made of fabric, which when sensed near an interaction point will trigger a moving graphic on the well screen with messages that were being exchanged among the freedom fighters. These messages will be in form of text/images/ montage etc to give the information of 30-60 seconds. 20 different types of text/images/ montage etc. messages will be created as per the requirement and suggestion of the museum design consultant to complete the experience.

NS Wooden Partition - 75mm (GI Framing with ply on both Sides) - Providing and fixing 75 mm overall thickness partition up to ceiling height consisting of G.I. frame with top cover of 12 mm commercial ply conforming to BWR grade of Greenply/Century ply or similar makes on both side with edge profiles, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm diametermeter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm diameterbolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and or ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Double Leaf Automatic Sliding Door- Frameless of 3000 MM clear opening X 2500mm height - Providing & Fixing of Automatic Sliding Door , Modular Design and customisbale colo with operator dimensions 168mm W x 92mm H x 4.2 Mtr L for max. opening size of 3.0Mtr Wide & Weight capacity for double Leaf Door is 2x120 Kg .Microprocessor Controlled unit will be self learning with adjustable parameters for opening & closing speed, hold open time, reversing when obstacles are encountered. Operator will have 65W DC brush-less Motor, international Make Timing Belt. Operator can be intgrated with Microwave Sensor / Presence Detector Sensor / Foot Switch Sensor / Handwave sensor, Safety Beam (Light Barrier), Programmable Remote Control to Set different modes & Automatic Locking Mechanism, RFID / Biometric / Fingerprint / Access Card Control System & Push Button. Inclusive all necessary fixing hardwares Cost includes the concelaiment of wire from the source to the mechanism of automation. This also includes the Providing and fixing of 12mm thk toughened glass of make Saint Gobin/Modi/Asis/eqv for automated sliding door with framework and hardware as per drawing. Rate to be quoted shall include the cost of all the fixing hardwares screws/nutts/bolts/screws/uv glue/ required for the fixing with Automated sliding door machine with water and air proofing using appropriate materials and hardware.( hardware , hinges, handles, door stopper, locks ). The exact size of the glass to be checked as per the site and the shop drawings should be approved by the design consultant. Additional casing , with top cover duly painted with exterior grade duco of 5 year warranty for the automation machine should be included in the cost to to prevent dust and water getting in. Make - Dorma/Hafle/Hettich/Geze and

NS Wooden Partition - 150mm (GI Framing with ply on both Sides) - Providing and fixing 150 mm overall thickness partition up to ceiling height consisting of G.I. frame with top cover of 12 mm commercial ply conforming to BWR grade of Greenply/Century ply or similar makes on both side with edge profiles, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm diametermeter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm diameterbolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and or ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS SITC of Fixed Ring Ceiling Recessed luminaire with 6 optical elements for LED lamps - with approx 12W giving atleast 850lm in 3000/4000K CRI90 minimum.The optic system guarantees a high level of visual comfort and no glare. The body includes a radiant surface made of die-cast aluminium. Version includes a perimeter surface frame. High definition reflectors made of thermoplastic material vacuum-metallised with aluminium vapours, integrated in a set-back position in the antiglare screen. Complies with EN60598-1 and pertinent regulations . The fixture should not have dia more than 90mm and depth more than 40 mm. Luminaire should accept all Dimming protocols. The Ring Luminaire should incorporate blank cover for the middle space. UGR<10 Lifetime: > 50,000h - L80 - B10 (Ta 25°C) Make:ERCO/ iGuzzini Blade R/ Fagerhult (AOR No.RA-22)

NS Live paintings with Interaction points - To dynamic visual will highlight the details of of each area/city/place will have a images/ lithograph/paintings etc. in front which will come alive once the visitor interacts with the painting. The painting/image will have an interaction point in front with an interactive touch screen/ sensor based object etc. which when touched by the visitor will trigger the painting in front and make it come live. when triggered the visual in front will give the details about that place/person. this live animation will be of 30-60 seconds each and at different locations each.The projection content will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval.

NS Wooden Partition - 300mm (GI Framing with ply on both Sides) - Providing and fixing 300 mm overall thickness partition up to ceiling height consisting of G.I. frame with top cover of 12 mm commercial ply conforming to BWR grade of Greenply/Century ply or similar makes on both side with edge profiles, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm diametermeter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm diameterbolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and or ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Gallery wall - The images of all the freedom fighter and the visitors of the museum will be displayed on the wall of the gallery in loop. The images of the visitors which are captured at different intervals in the museum will be reflected on the this wall as a part of the revolutionaries. The projection will be a grid like projection where each photo will appear for a duration of 30 seconds supported by details if required i.e. name, place of origin etc. At an instance approximately 50-100 images will appear on the wall at once. The treatment of the images will match the overall theme of the museum and the visual appeal as approved by the design consultant. The content to be developed as per the resolution of the screen.

NS Curved Wooden Partition - 150mm(GI Framing with ply on both Sides) - Providing and fixing 150 mm overall thickness partition up to ceiling height consisting of G.I. frame with top cover of 12 mm Flexible ply conforming to BWR grade of Greenply/Duroply/Century ply or similar makes on both side having bend radius as little as 100mm , ideal for tight radius work with edge profiles, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm diametermeter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm diameterbolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and or ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing. Inclusive of all - fixtures, fittings, hardware, hanging

NS SITC of Spotlight designed to use LED lamps with approx. 42W and system wattage not exceeding 48Watts at color temperature options 3000K/4000K Delivered Lumens to be more than 4800lm maintaining lumen efficacy of more than 100 lm/W. . The option of various medium, flood or Wide flood optics. The optical assembly and base is made of EN1706AC 46100LF, aluminium alloy and subjected to a multi-step, pre-treatment process, in which the main phases are degreasing, fluorozirconation (a protective surface film) and sealing (with a nano-structured silane layer). The following painting stage consists of a primer and a liquid acrylic paint, cured at 150°C, with a high level of weather and UV ray resistance. 5 mm thick tempered sodium-calcium closing glass. Double adjustability allows a 360° rotation about the vertical axis and 90° tilting relative to the horizontal plane. Mechanical aiming locks for rotation on both the vertical axis and horizontal plane. Complete with a monochrome LED circuit and an Opti Beam Reflector optic system. The product includes a PG13.5 cable gland. LED of MacAdam Step 2 Electronic DALI ballast integrated in product. Option of using optic accessories assembled via an accessory holder frame. All external screws used are made of A2 stainless steel. Mounting options of Floor, wall, ceiling or ground-installed via pole or stake. Complies with EN60598-1 and pertinent regulations. Life Time LED : 100,000h - L90 - B10 (Ta 40°C) Make:ERCO/ iGuzzini/ We-ef or eqv (AOR No.RA-27)

NS Terracotta wall panelling (GI frame with Terracotta Finish Mud Plaster) - Providing and fixing 50-150 mm overall thickness partition up to ceiling height/as per design consisting of G.I. frame and top cover of wire mesh gauge on both sides to be finished on top surface with mud plaster giving look and feel of Terracotta Plaster with appropriate paint to give final finish, including providing and fixing of frame work The terracotta plaster finish to have gerua colour in final finish and the plaster should have minimum / light cracks, with rough texture as per the approval of the museum design consultant. Refer image in tender presentation for sample finish required.

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3C x 4 sq. mm. 2XWY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 4C x 4 sq. mm. 2XWY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 4C x 16 sq. mm. 2XWY

NS Printed Fabric Panelling with cushioning on one side - Providing and fixing of 50-150 mm thick wooden paneling with wooden batten framing at 600mm c/c both ways with top cover of 6-12 mm commercial ply wooden board BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc . The wooden panel to be finished on top with stain free custom made fabric skin, the fabric should be resistant to wear and tear, made of polyester/cotton. Fabric to be block printed as per theme given and as approved by museum design consultant. Inclusive of all - fixtures, fittings,hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 95 sq. mm. A2XFY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 185 sq. mm. A2XFY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 300 sq. mm. A2XFY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 12C x 2.5 sq. mm. 2XWY

NS E- Board Partitions (With MS Frame) - Providing and Fixing of 50- 150mm overall thickness partition using 12-18mm multipurpose cement bonded wood particle board manufactured as per IS: 14276 with suitable cement bonded board screws on both sides of the fixed frame work for partitions/ wall lining etc. including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge. Cement board to be top coated with concrete render (made up of three main components – lime, sand and cement), to give it a smooth concrete finish. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS M.S Framework - Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge. (AOR No.RA-17)

NS Concrete Tile cladding - Providing and fixing of concrete tiles of Dimensions as per detail design with Sleek finish . The concrete 3D tiles of Dimensions as per detail design to be fixed on wall with cement sand mortar mix ratio 1:6 (1 cement : 6 sand) upto 25mm thick as wet cladding (on civil structure), joints to be cleaned and grouted with matching colour approved quality polymer based readymade grout (Laticrete or equivalent). The tiles shall be laid and fixed with pattern, style and orientation as directed by the Museum design consultant.

NS Corten steel sheet Panelling - Providing and fixing 3-5 mm thick corten steel fixing on existing ms structure with waterjet /laser/plasma cutting,supported with ms tubular section and base plate and fastened with hilti fastener and structurally approved, with required foundation work as per approved structure design.

NS Gypsum Partition - Providing & Fixing in position, Partition made from 6-18 mm thick Gypsum from both sides on 50 x 50 mm Sal- wood frame of 600 x 600 c to c, having of 800 gsm synthetic wool 50 mm thick in between, including cost of required Cut-Outs & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour, finishing etc complete as per the direction of engineer in charge. (AOR No.RA-18)

NS Acrylic - Providing and fixing 3-8 mm thick laser cut acryllic elements Installation on wall, based on concept and design approved by the museum design consultant.

NS Concrete rendering - Concrete Rendering on the wall properly finished as per the approval of the designer / engineer in charge

NS WPC Partition -6 mm/12 mm - Providing and fixing factory made single extruded WPC 6mm-12mm thk (Wood Polymer Composite) solid board one side white color board for backing of cup boards and bathroom/kitchen cabinet etc. of required sizes comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 29 gms) having minimum density of 650 kg/cum, screw withdrawal strength of 1800 N(Face) & 900 N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel screws etc. all as per direction of Engineer-In-Charge.

NS Ceramic printed panel - Ceramic printed panel-Providing & fixing of printed ceramic panel of size as per detail design and graphic as per the approval of the museum design consultant vertical dry cladding 10 -35 mm thick in required position on ms clamp and complete and loading, unloading, transportation and including all other taxes and excluding GST complete as directed by Engineer In charge.

NS Acrylic/vinyl backlit panelling - Providing and fixing of 6-12mm thick toughened and backlit Glass panels with laser cut paper and coloured acrylic sheet pasted behind , panel of size as per detail design. All detail as per design and approved by Museum design consultants. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional as per the design, to achieve the effect of only text/graphic being lit up.

NS Wooden finished Partition - Providing and fixing of 1-4 mm thk teak veneer laminate paneling on top of existing wooden partition, duly polished with melamine/PU finish. Finished as per requirement. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Vinyl plotter cut - Vinyl Plotter Cut - Providing and fixing of vinyl plotter cut- with 1 year warranty on pre finished primer base surface Walls, as per approved size and graphic design.

NS Stretched fabric Partitions (Backlit) - Provision, fixing & application of Backlit Graphic Panel fixed to the floor & ceiling for necessary support also known as Silicon Edge Graphics (SEG) of 150 - 300 gsm polyester fabric(make:- Barisol,LG,Dinolax), FR rated, giving a edgeless or frameless feel made out of metal frame, and a fabric material using a UV printing process the setup to be Complete with all the necessary hardwares and graphic as per the approval of the museum design consultant.

NS Sliding Wooden curved Partition - 75mm - Providing and fixing 75 mm overall thickness curved sliding/openable partition up to ceiling height (up to 6 meters)consisting of G.I./ms frame with top cover of HDWR / HDMR conforming to BWR grade on both side with edge profiles, including providing and fixing of frame work made of special section, formaldehyde free, fire retardant. Make Sipla/ UP Twiga/ Orwens Corning / - Installed with MS wire mesh. Installation complete with all necessary Hardware. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical,sliding rails,remort control or any other mechanism required to make it functional. the automated opening mechanism should seamless in visual and audio should be synced with the AV content played in the insallation for opening and closing.

NS Wall mount paneling with MS frame work 75 - Providing and fixing of 75 mm thick wooden paneling with 50 x 50 mm MS sections framing at 600 mm c/c both ways and top cover of 18 mm commercial ply wooden board BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc. The wooden section to be coated with anti termite coat and wooden battens used should be good quality wood. The wooden frame should be fixed on floor/wall/ ceiling with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and primer coat on unexposed surface complete. Cost of primer base on base to be considered. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Fibre Glasswool Insulation - Providing, filling/fixing of fiberglass wool insulating wool/ board in between the partitions as per required location/installation as approved by the designer. The type/density of insulation taken should be checked by the sound consultant depending on the intensity of the sound and its spillage in the surrounding. The fiberglass wool should not retain moisture more than 2%, be odorless, fire safety and all other factors suggested best as per the sound consultant.

NS Curved Wooden Partition - 150mm (with ply on both Sides) - Providing and fixing wooden partition with base frame made up of wooden battens placed at 600mm c/c both ways and top & back cover of 6mm thick flexi ply wooden board BWR grade of Greenply/Century ply or similar makes on front side with edge profiles, beadings s etc.

NS acrylic solid surface Skirting - Providing and fixing of12mm thk Acrylic solid surface with ply backing -On Skirting made in Bendable acrylic solid surface, minimalist skirting, allowing to create an elegant and refined wall-to-floor connection. Equipped with a projecting tab, skirting board guarantees excellent coverage in the perimeter area, meeting the technical requirements of floating floors and concealing minimum perimeter expansion spaces. Height : - 50 to 100 mm, Colour - as per desired colour. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Make : Dupont/LG/Durlax

NS Free standing Wooden Partition - 300mm - Providing and fixing 300 mm overall thickness free standing partition up to 5 meter height consisting of 75X75 mm wodden frame also the appropriate structural support from ceiling of floor if required with top cover of HDWR / HDMR conforming to BWR grade on both side with edge profiles, including providing and fixing of frame work made of appropriate size of wodden battens and space for infilling of Acoustical insulation within the Frame structure, formaldehyde free, fire retardant. Make Sipla/ UP Twiga/ Orwens Corning / - Installed with MS wire mesh. Installation complete with all necessary Hardware. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. The structural stablity to be vet by and the astehtic value to be approved by the design consultatnt

NS Free standing MS Partition - 300mm - Providing and fixing 300 mm overall thickness free standing partition up to 10 meter height consisting of 75X75mm MS sections also the appropriate structural support from ceiling of floor if required ,with top cover of HDWR / HDMR conforming to BWR grade on both side with edge profiles, including providing and fixing of frame work made of appropriate size of MS sections and appropriate space for infilling of Acoustical insulation within the Frame structure, formaldehyde free, fire retardant. Installed with MS wire mesh. Installation complete with all necessary Hardware. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.The structural stablity to be vet by and the astehtic value to be approved by the design consultatnt

NS Wall mount paneling with MS frame work 300 - Providing and fixing of 300 mm thick wall mounted paneling with minimum 75 x 75 mm MS sections framing at 600 mm c/c both ways and top cover of 18 mm commercial ply wooden board BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc. The wooden section to be coated with anti termite coat and wooden battens used should be good quality wood. The wooden frame should be fixed on floor/wall/ ceiling with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and primer coat on unexposed surface complete. Cost of primer base on base to be considered. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Aluminium Skirting - Providing and fixing of Aluminium Screw-On Skirting made in anodized aluminium, minimalist skirting, allowing to create an elegant and refined wall-to-floor connection. Equipped with a projecting tab, skirting board guarantees excellent coverage in the perimeter area, meeting the technical requirements of floating floors and concealing minimum perimeter expansion spaces. Height : - 75 mm, Colour - as per desired colour. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional

NS Wall mount paneling with wooden frame work 300 - Providing and fixing of 300 mm thick mounted paneling with minimum 75 x 75 mm wooden batten framing at 600 mm c/c both ways and top cover of 18 mm commercial ply wooden board BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc. The wooden section to be coated with anti termite coat and wooden battens used should be good quality wood. The wooden frame should be fixed on floor/wall/ ceiling with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and primer coat on unexposed surface complete. Cost of primer base on base to be considered. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Wall mount paneling with MS frame work 150 - Providing and fixing of 150 mm thick wall mounted paneling with minimum 75 x 75 mm MS sections framing at 600 mm c/c both ways and top cover of 18 mm commercial ply wooden board BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc. The wooden section to be coated with anti termite coat and wooden battens used should be good quality wood. The wooden frame should be fixed on floor/wall/ ceiling with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and primer coat on unexposed surface complete. Cost of primer base on base to be considered. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Wall mount paneling with MS frame work 75 - Providing and fixing of 75 mm thick wooden paneling with 50 x 50 mm MS sections framing at 600 mm c/c both ways and top cover of 18 mm commercial ply wooden board BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc. The wooden section to be coated with anti termite coat and wooden battens used should be good quality wood. The wooden frame should be fixed on floor/wall/ ceiling with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and primer coat on unexposed surface complete. Cost of primer base on base to be considered. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Railing Glass - Providing and fixing of 12mm thick toughened glass, of height 900 mm , divided into divisions of 1200 mm or equal divisons as per site conditions. The rate to be inclusive od bevelling of all the edges and making necessary holes and inclusive of hardwares required to make it complete as per the satisfaction of engineer in charge. Make: Saint Gobain, Asahi India, eqv (AOR No.RA-19)

NS Canvas fabric paneling - Providing and fixing cotton / polyester based canvas cloth paneling jointless with coushioning as base. Cost is inclusive of installation of fabric with all necessary hardware, screws, nut bolts, etc. complete.Paneling should be done on straight/curved/vertical/horrizontal surfaces with minimum possible joints as per the design consultant. Provide rate only, payment will be made based on actual quantities , as per conceptual design & approval by Museum.

NS Aluminium tinted Glass Partition - Supply and installation of tinted Glass saint gobain or with custom colored thoughened glass of 12mm thickness in minimal Anodized aluminium glazing profile of section of required size and color in the Museum as per vendor specs .the glass should be factory tinted .the frame should be by a top chanel and bottom chanel.there should be no frame othervise and should be seald perfectly with not leakage and passage of airThe cost should include all the neccesary Hardwares for the fixing of glass panels, aluminium section,etc as approved by designer and complete as per the direction of engineer in charge. (AOR No.RA-20)

NS Acrylic solid surface Panelling - Providing and fixing of 6mm-12mm thk bendable acrylic solid surface of make Dupont/Samsung/ , installed on site with necessary hardware/framework/as per manufacture specifications and site conditions.Necessary finish materials to be considered, to make bendable acrylic solid surface abrasion resistant as per approval by Museum Design Consultant. as per conceptual design provided by Museum consultant. Make : Dupont/LG/Durlax

NS Ceiling (Baffle) - Providing and fixing of customised baffle ceiling of U shaped anodized/powder coated Aluminium panel of approved colour consisting of basic panel size of 75X40mm with a thickness of 0.5mm to 0.8mm with edges sealed with U shaped baffle cover as per the direction of museum design consultant. The rate is inclusive of installing the baffle at varying heights as per approved drawing by clipping the panels to a baked enamelled Aluminium carrier of colour coated as per approved shade including one leg of the carriers with cut outs to hold the panels in a module fixed to the ceiling with suspended rod of desired length from ceiling. : Ceiling area above U Baffle to be painted in colour before fixing this system. (AOR No.RA-22)

NS Ceiling Wooden carved - Providing and fixing the engineered natural wooden board of approved thickness, texture and size as per design. The rate is inclusive of providing framework consisting of 50X50mm/75X75mm/ as per site requirement wooden battens in a grid pattern with upto 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions with screws, nails, adhesives and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for electrical conduits etc. wherever required. The ceiling members to be suspended from the structural ceiling at a distance of upto 900mm. The form of the ceiling to be varying from flat/slanting/curves as per design. Also includes the designing and fabrication of various custom made geometrical patterns skillfully crafted by special artist on the board with a saw for obtaining decorative wooden shape as per the satisfaction of museum design consultant following the basic theme of the area.

NS Engineered Bamboo ceiling - Providing and fixing the engineered natural bamboo/ Bamboo Ceiling Board of approved thickness and size as per design. The ceiling members to be suspended from the structural ceiling at a distance of upto 900mm. The form of the ceiling to be varying from flat/slanting/curves as per design. Ceiling area above the bamboo ceiling to be painted in colour of matching shade before fixing this system.

NS Queue Manager - Providing of Queue managers of approved made, installing as per Museum Design Consultant.

NS dustbins - Providing and fixing black MS dustbin approved by Museum consultant.

NS Gypsum False Ceiling - 600mm - 900mm depth from slab level - Providing and fixing false ceiling at 600mm to 900mm from slab level ; maintain appropriate clear height from FFL including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diameterx 50mm long with 6mm diameterbolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm diameterx 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint , all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut-outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks)Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. (AOR No.RA-21)

NS Tree leaves ceiling - Providing and fixing of tree leaves in frp/ acrylic/ plastic/paper finished in paint/polish/duco as approved by the museum design consultant. The size of the leaves will vary tentatively from 80-150mm wide to 100-200mm long as per approved design. The leaves to be clustered such that the light rays can be filtered through the leaves and create forest like lighting ambience. Te cost is inclusive of fixing in place the installation with necessary hardwares, fixtures, adhesives etc all complete as per the satisfaction of engineer in charge.

NS Reflective ceiling - Providing and fixing of ceiling of reflective material such as S.S./M.S./glass/acrylic sheets of size as per design. The ceiling may have reflective film if required. The ceiling to be complete with all the necessary hardwares and accessories required for the ceilig suspension and durability.

NS Ply and MS frame work False Ceiling - - Providing and fixing false ceiling at required height from slab level ; maintain appropriate clear height from FFL including providing and fixing of frame work made of special sections, power pressed from M.S. sheets/M.S. angles/M.S. tubular sections as per the sructural weight and requirement, including all M.S. cross and sections designed as per the requirements and design with all suppporting functions and hanging mechanism made up of galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 900 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diameterx 50mm long with 6mm diameterbolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate channels 45x15x0.9 mm running at the spacing of 900 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to MS intermediate channel with connecting clips made out of 2.64 mm diameterx 230 mm long wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of 12 mm thk wooden ply on ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing and also including the cost of making openings for light fittings, grills, diffusers, cut-outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. (AOR No.RA-23)

NS Perforated ceiling - Providing and fixing of perforated metal false ceilings with perforation pattern as per the approval of museum design consultant. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical,mechanical or any other mechanism required to make it functional.

NS Canvas ceiling - Providing and fixing of canvas false ceiling as per the approval of museum design consultant. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical,mechanical or any other mechanism required to make it functional.

NS Vinyl ceiling - Providing and fixing of vinyl false ceiling as per the approval of museum design consultant. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical,mechanical or any other mechanism required to make it functional.

NS Benches - Providing and fixing of backless bench of size- 1800mmX450mmX450mm in 38X38mm square mild steel pipe with 25 mm stone/5 mm thk Mild Steel sheet on top followed by smooth sanding with emery paper no. 320 or 400, finished with surface base and final coat of fast drying matt finish Duco paint with compressor machine. Colour shade and sample bench to be approved by Museum Design consultant.

NS Specialized glazing film - Provision and fixing of specialized glass films on the facade glazing for controlling light and vision through the glass.

NS Metal mesh ceiling - Framework: Providing and fixing false ceiling at reuired height from slab level ; maintain appropriate clear height from FFL including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 900 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diameterx 50mm long with 6mm diameterbolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate channels 45x15x0.9 mm running at the spacing of 900 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to MS intermediate channel with connecting clips made out of 2.64 mm diameterx 230 mm long wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval,fixing of solid/perforated metal sheet ceiling finished in desired color and texture as approved by the museum design consultant. Thickness of the metal sheet to be approriate for bending and folding of the sheet and as approved by the museum design consultant and also including the cost of making openings for light fittings, grills, diffusers, cut-outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. (AOR No.RA-24)

NS Acrylic ceiling - Providing and fixing of Translucents Luminous Infill Ceiling Panels of acrylic sheet - made of solid or transperent acrylic sheet with decorative designs with LED light or panel light as per the approval of museum design consultant. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical,mechanical or any other mechanism required to make it functional.

NS Mirror/Printed Glass - Providing and fixing of false ceiling of mirror panels as per the approval of museum design consultant. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Grid Ceiling-aluminium interlocking - Providing and fixing in true horizontal level 600 mm. X 600mm/as per design false ceiling system using hot dipped galvanized steel section, exposed surface with pre-coated capping, The grid is suspended at every 600/1200mm c/c. in both directions using prestraightened GI wire laying Fine Fissured butt Edge ceiling tiles surface having 3 coats of white/colored paint with Fine Fissured, back of the tile duly sanded and finished with a coat of protective paint over the formed grid complete.

NS Micro-topping ceiling - Providing and laying micro-topping ceiling system composed of polymer (not water) mixed with special cement admixture of desired shade, texture and approved make as per the direction of museum design consultant. The rate to be inclusive of preparing a sub base free of dust, laitance, oils or any loose material with a provision of any expansion, contraction and crack inducing joints to avoid cracking, unevenness and faults, including application of Epoxy-coat mixed with 20% quartz-sand (0,2-0,5mm) as adhesion primer and covering thoroughly the surface with quartz-sand on substrate. Rate includes the application of two coats of base coat with 0.5mm coarse sand used as gauge evenly spread upto maximum thickness of 0.5mm. Followed by application of upto two coats of very thin layer of finish coat or high-performance coat without coarse sand for smooth appearance. The final coat is to be sealed with acrylic or PU sealer all complete as per the direction of engineer incharge. Approved make : Bharat Flooring/idealworks/eqv

NS POP False Ceiling - Providing and fixing false ceiling at 700mm-1200mm from slab level ; maintain clear height of 4350mm from FFL, of 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, reinforced with rabbit wire mesh fixed to 24 gauge GI sheet main rafters of size 50 mm with flanges on either sides from the soffit 1000 c/c ,suspended with 25 mm x 2 mm MS hooks with steel expansion fasteners from the RCC slab, ceiling section of 24 gauge GI sheet channel of size 40 mm with flanges on either side from soffit at 355 mm c/c fixed to the runners with steel screws and applying 10 mm thick first coat of plater of paris layer finished with smooth surface including the cost of making openings for light fittings, grills, diffusers, cut-outs made with frame of perimeter channels suitably fixed, all complete as per specification and direction of the Engineer in Charge . No extra will be paid for light cuttings/grills/diffusers, cut-outs , trap door etc. No extra channel will be paid if its is required for additional support etc. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. (AOR No.RA-25)

NS Trap Door - Providing and fixing trap door with 19 mm thick MR grade plywood with moulding in edges, Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Size 1000mm x 1000mm

NS Wooden Batten False Ceiling - Providing and fixing of false ceiling of wooden block solid battens - made of teak wood as per existing site finish. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional.

NS Beaten metal - Providing and fixing of false ceiling of stainless steel - made of beaten metal to create an shimmering effect as per the approval of museum design consultant. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical,mechanical or any other mechanism required to make it functional.

NS Reception table size - Providing and fixing of 10000mm X 1050 mm X 800mm reception table partially straight and partially curved made in special square pipe sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 of size 50X50mmX2mm MS square pipe frame with 18mm thick commercial plyboard 12mm thk acrylic solid surfaceon top/ microtopping finish as approved by the museum deisgn consultant. Inclusive of 2 no's drawer unit 600mm x 450mm made in 18mm thk Block Board finished (outside) with 2 nos. drawer and 1 nos. file storage space with shutter finished (both inside and outside) with 1mm thick laminate inside with face finished in acrylic solid surface or any other necessary finish as per drawing and as approved by museum consultant. The hardware and fittings to be hettich/haffele/ equivalent. All shelves, drawers, designer handles, lockable drawers with necessary first class hardware and adhesive approved by museum Consultants. The rates are inclusive of artwork/deisgn in etching/laser cutting/cnc in acrylic solid surface/wood/metal/glass as per approved by musuem design consultant. With Print ready designed graphics , illustrations / artwork and Copywriting and editing of bilingual textual content as per conceptual design provided by Museum consultant. Under special conditions, the size of the table may vary and cost considered to be under prorata basis proportionately.

NS Reception chairs - Supply and installation of Feather lite / Similar Make - Liberate Medium Back Desk Arm Chair (Black) or of similar make from Feather lite / Durian / Wipro / Godrej/eqv. Product Dimensions: Length (43.00 cm), Width (48.50 cm), Height (101.50 cm) Primary Material: Mesh, Upholstery Material: Fabric Colour: Black, Style: Mid Back, The chair is built with health orientated ergonomics in mind. Assembly Required: The product requires basic assembly and comes with assembly instructions Warranty: 3 year warranty against manufacturing defect's. Maximum weight handling capacity while seating in a reclined position is between 120 to 150 kg.Moulded polyurethane arms confirming to IS 7078 with steel inserts for long life, one way adjustable - height adjustable. Easy do it yourself assembly with instruction manual. Duly upholstered seat with approved fabric for maximum comfort, mesh fabric used for back upholstery with unique two piece dynaflex for breathability and maximum comfort. With tension control below seat for reclining. Refer Furniture Options Document for further clarification. Model To be approved by museum design consultant.

NS Seating - Providing and fixing of backless bench of size-1500mmX450mmX450mm in 38X38mm/50X50mm square mild steel pipe with necessary welding at junctions including providing and fixing of 12mm to 18mm thk plywood/board on all five sides of the framework with hardwares, screws etc all complete. The rate is also inclusive of providing and fixing of 6mm to 12mm thick corian of approved shade and make on top/sides as per approved drawing including all the necessary hardwares, fixtures, adhesives etc all complete with corian surface finished with buffing and polish on all visible areas as per the satisfaction of museum consultant.

NS Corian table (1500x450mm) - Providing and Fixing of table of size 1.5 x .45mm with height .90 mm with base made of 50X50mm hollow sections of desired thickness with appropriate spacing and necessary welding at junctions including applying of required coats of steel primer on sections. The cost is inclusive of providing and fixing 12mm thk commercial ply of approved make on MS frame work with necessary hardwares,screws etc all complete. The top to be finished in 12 mm thk corian of approved make and shade fixed to the ply with silicone adhesives including buffing and polishing of the surface as per approved drawings. The corian top will be etched with artwork. The remaining area to be painted in duco of approved shade. Under special conditions, the size of the table may vary and cost considered to be under prorata basis proportionately.

NS Racks - Providing and fixing of rack made in MS, shelves made in 3mm MS sheet and supported by MS section of profile as per design, including all hardware, fixtures fittings or any other mechanism required to make it work. Complete assembly to be powder coated in approved shade as per Museum Design Consultant.

NS Acrylic solid surface bench - Providing and fixing of backless curved/straight bench in 12 mm bendable Acrylic solid surface finish of approved shade and make of size - 1500x450x450mm as per the space as per the approved detail drawings. The bendable acrylic solid surface should be be backed with appropriate MS structure 50X50 mm hollow sections of desired thickness with necessary welding at junctions. The cost is inclusive of proving and fixing 12mm thk flexible/normal ply of approved make with necessary hardware, screws etc all complete as per the direction of engineer in charge. The cost should also be inclusive of all necessary adhesives, grinding, buffing etc for installation of bendable acrylic solid surface on the base. Sample bench to be approved by Museum Design Consultant. The bench should also have a 2D/3D graphic as a museum branding or as per the design language of the space.

NS Lockers - Providing and Fixing of CKL Locker, stackable storage (up to 4 level), Key Lock Type Cabinet bodies are made of 0.8mm steel with a top edge profile of 10mm. Side panels are of folded steel structure of an overall thickness of 18mm. Drawer/door fronts are in steel with powder coating finish. Width 515mm, Depth 600mm, Height 530mm.As approved by museum Consultants. Refer Furniture Options Document for further clarification.

NS Window Roller Blinds - Rollar blackout Blinds:Providing and Fixing of roller blinds of variable colour and customised design :Ivory Mount Type :Wall Mount & Ceiling Mount Wash Care :Spot Clean Fabric :Faux Wood Transparency :10% , Chlid Saftey lock providing manual folding over and the frame should be in desired color.

NS Step Ladder - Providing and Installing of custom made step ladder for library , to access books kept in ceiling mounted Pre Fabricated Book Shelf. The step ladder to be made in 75x75x75mm wooden sections, with polished in natural finish /Duco Finished. The step ladders should be movable in nature and of height - 600mm and step tread 120mm and step raise 180mm

NS Custom Made Shelf - Single side - Providing and fixing of Pre Fabricated Book Shelf in structural niches, as per exact site dimension in 38mmX38mm/ 50mm x 50mm/ as per requirement on site of desired thickness with MS/ Aluminium box section frame with necessary welding at junctions. The shelf top to be finished in MS/Aluminium/ of desired thickness and finished with two to three coats of Duco paint of approved shade. The cost is to be inclusive of scrapping the surface with emery paper of required grade to provide a dust free surface. It is also inclusive of providing one coat of duco putty wherever required to provide a smooth surface for application all complete as per the direction of engineer in charge. The quoted amount to include mounting the book shelf from ceiling or wall as per approved design with all necessary hardware, welding, grinding, screws etc. all complete. Sample to be approved by Museum Design Consultant.

NS Custom Made Shelf - Double side - Providing and fixing of 750x3000x2400 mm Pre Fabricated Book Shelf to be provided in structural niches, as per exact site dimension in 50mm x 50mm x 2mm box MS/ Aluminium pipe section frame and shelf top finished in MS/ALuminum of 2mm thkness and finished white Duco paint. The book shelf will be mounted from ceiling, inclusive of all necessary hardware, welding, grinding, colour etc. Sample to be approved by Museum Design Consultant, as per detail drawing.

NS Guard Desk + Storage - Providing and fixing of Gaurd desk of size 1650x350x1040mm, made in MS frame work of 35X35mmX3mm MS square pipe frame and 12mm commercial ply greenply/ and on top finised with 12 mm acrylic solid surface with a storage of size 900x300x1050mm made with 3mm thk powder coated MS as per dwg at all entry/exits of the museum. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Make : Dupont/LG/Durlax

NS Bench - Type 1 - Providing and fixing of backless bench of size - 450mm Width X 450mm Height and 450 length as per the space requirement in Pre-casted in Terrazzo/Concrete as per design and instructed by museum Consultants. The casting in Terrazzo finish shall only be done using stone chips of khavada stone. Terrazzo finish to be seamless both on top and on the base as per the drawings. Inclusive of All grinding and finishing with necessary hardware. Sample bench to be approved by Museum Design Consultant. Terrazzo casted for bench to embed museum branding graphics while casting

NS Bench - Type 2 - Providing and fixing of backless curved/straight bench in 12 mm bendable Acrylic solid surface finish of size - 450mm Width X 450mm Height and length as per the space as per the detail drawings and instructed by museum Consultants. The bendable acrylic solid surface should be be backed with appropriate MS structure (50X50 MM) and 12mm thk flexible/normal ply. Inclusive of All grinding and finishing with necessary hardware. Sample bench to be approved by Museum Design Consultant. The bench should also have a 2D/3D graphic as a museum branding or as per the design language of the space.Make : Dupont/LG/Durlax

NS Blackout Light Curtains - Providing and fixing of blackout light curtains of required length. The curtain fabric should be durable enough for use in public space and curtain mechanism should have smooth rail movement, with provision for manual movement of the curtains. Color to be approved by the design consultant.

NS Stackable Stools with Stool Hanging System - Proving and fixing of custom made / pre fabricated modular foldable stools that can be stacked on the wall itself with appropriate hanging system. Refer moodboard in tender presentation. Including floor stand for folding 5No.s stools - 15No.s , Wall-mounted holder for 5 or 10 folding stools - 15 No.s. Make - STOCKHOLM II, Lectus Produktion or similar.

NS Concrete Table top - Providing and fixing of Concrete table top of thickness 25 to 50 mm and size upto 1200mm dia as per approved by designer refreing to the designe asthetic having 50% of concrete printing/etching/inlay over the top. No separate cost for finish to be considered. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional as per the design.

NS MS Metal artefact casing - Providing and fixing Artefact table with MS/wooden framework and w.p.c board and enclosed with Metal sheet/Ply of size as per design and extra clear glass casing printed/lacquered glass base for the artefacts/replicas as per the specifications and drg as approved by the Engineer in charge

NS MS Metal Podiums - Providing and fixing Artefac podiums with MS/wooden framework and w.p.c board of size as per design enclosed with Metal sheet /ply on the sides with printed/lacquered glass/Vinul/corian base for the artefacts/replicas as per the specifications and drg as approved by the Engineer in charge .

NS Souvenir display rack - Souvenir shop display :-Providing and installing Souvenir shop display rack of following the details mentioned below. Any difference in size will be taken on prorata basis. a) shelf be made of 3mm/5mm thick MS sheet top as per drawing.MS sheet to be smooth sanding finished with surface base and final coat of fast drying matt finish Duco paint with compressor machine as approved by Museum design consultant. b) Fabricating and fixing storage shelf Of size Made of 12-18 mm ply with 4-8 mm Corian covering Or 3-5mm MS sheet /ply painted in duco c) Necessary hardwares like fully extendable drawer slides, locks, SS handles etc.complete, of approved make. d) Cost should include Anti antrust treatment on MS sheet. e) Shop to be made complete as per the drawings and details complete as per the approval of museum design consultant.

NS Wood artefact casing - Providing and fixing Artefact table with Wooden batten framework and w.p.c board and enclosed with 6-18 mm Ply finished with duco paint/as per the approval of the museum design consultant of size as per design and extra clear glass casing with printed/lacquered glass base for the artefacts/replicas as per the specifications and drg as approved by the Engineer in charge

NS Lockable Glass case- Type 1 - Proving and Fixing of custom made Lockable glass dome with rubber gasket edging, made in 8- 12 mm toughened glass of ht 250-600mm and diameter - 300-450mm /as per detail drawing. Sample Display unit to be approved by museum design consultant before installation.

NS Wooden bench - Provision & fixing of wooden benches for visitors as per design with teak finish as per design and complete as per satisfation of Engineer in Charge.

NS Boughtout furnitures - P/F chairs/table. Make - Neelkamal Equivalent/ Featerlite as approved by museum design consultant

NS Acrylic copolymer paint - Providing and applying 2 Coats of high quality acrylic copolymer matte latex low VOC emulsion paint of approved shade that gives smooth, flat and washable and durable finishing of approved make. Paint should have good flow levelling property with good colour retention and incan antibacterial property. Paint has to be applied on smooth and uniform surface prepared by an acrylic copolymer low VOC & Odour putty. This surface should be primed with water based low VOC acrylic copolymer based primer sealer that has incan antibacterial property. The work activity should cover all aspects of applying paints from surface preparation, filling to erecting and dismantling of scaffolding, finishing the surface etc as directed by Engineer in charge.

NS Projection Paint - Providing & applying plastic projection Finish paint on walls matt finish and high gain, columns & ceilings. The rate shall include scrapping, levelling & preparing the surface. Primer coat (Asian/ Nerolac/ Berger) + (minimum) 3 coats to get evenly spread quality finish (roller finish) of approved make, quality & finish shall be provided as directed by Museum Consultants. Finish with wall putti wherever necessary before paint

NS Duco Paint Finish - Providing & applying plastic Duco Finish paint on walls, columns & ceilings. The rate shall include scrapping, levelling & preparing the surface. Primer coat (Asian/ Nerolac/ Berger) + (minimum) 3 coats to get evenly spread quality finish (roller finish) of approved make, quality & finish shall be provided as directed by Museum Consultants. Finish with wall putti wherever necessary before plastic emulsion paint)

NS Vinyl Graphic Printing and Design - Providing and applying of NON PVC, 3M/eqv vinyl with 3 to 5 year warranty on both printing and material , with custom designed graphics / 2D artwork , illustrations / artwork and Copywriting and editing of textual content in Hindi, English, as per approved conceptual design. The cost is to be inclusive of designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English, as per conceptual design provided by Museum consultant.

NS UV printing - Providing and printing , with UV Printing techniques of Large Format Graphics/ Second Surface Printing/ Double Layer Printing w/ White Ink / Clear Ink , Up to 4’ x 8’ , Compatible with both rigid and flexible materials - including Glass, Acrylic, ABS, Coroplast, Aluminium, Metal, Foam board. Provide rate only, payment will be made based on actual quantities , as per conceptual design & approval by Museum Design Consultant. as per conceptual design provided by Museum consultant.

NS screen printing - Providing and printing on smooth finished concrete , wood, metal with screen printing techniques, with the use of water based inks/ any other appropriate ink to create perfectly finished and smooth end product. The ink printed should be sealed with appropriate sealant after drying. Provide rate only, payment will be made based on actual quantities , as per conceptual design & approval by Museum Design Consultant. Rate to be quoted shall include the cost of custom designed graphics / 2D artwork , illustrations / artwork and Copywriting and editing of textual content in Hindi, English as per conceptual design provided by Museum consultant. With designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English as per conceptual design provided by Museum consultant

NS Polymer fabric printing - Providing polymer fabrics jointless with printing. Cost is inclusive of installation of fabric with all necessary hardware, screws, nut bolts, etc. complete. Paneling should be done on straight/curved/vertical/horizontal surfaces with minimum possible joints as per the design consultant. Provide rate only, payment will be made based on actual quantities , as per conceptual design & approval by Museum.

NS Lime finish on walls - Plastering the wall/panel surface in 1 : 1 : 1 lime plaster (1 lime : 1 surkhi : 1 fine sand) prepared by traditional practice of adding organic additives of gur, guggal, methi as per the directions of conservation architect. The work has to be carried out as per the specified lime plaster techniques and instructions of site supervisor. Providing final coat of high quality lime wash prepared using seived and refined lime lime putty mixed with organic additives guggal, belgiri, jaggery and natural gum, two coat as per the instructions given by Museum design consultant.

NS Projection screen - Providing & fixing of Ultra Gain projection screen of high quality material of Standard sizes from 42”-134” & self adhesive material. The screen should be seamless with no joints and the projection outcome should not be compromised. All provision for mounting the screen onto the framwork like aluminum/ any other profile, edge detail to be included in the rate. Make - ProDisplay or .

NS Mettallic paint - Providing and applying thermoplastic-acrylic solvent-based paint of approved make & approved brand of approved quality, colour and shade to old and new surface of exi in two coats, including exterior acrylic primer coat, scaffolding, preparing the surface etc. complete (Heat Reflective Paint). (AOR No.RA-26)

NS Free Standing Corten Steel Information SignageWith Stone Backing & MS Framework) - Providing and fixing of Free Standing Corten Steel Information Signage consisting of Steel / Metal frame work for support with 25mm thk Khavada stone backing finished on top surface with 4mm thk corten steel sheet with CNC cut Artwork in 50% of the area of signage surface and backed with 25mm thk Khavada stone backing. Item Rate to include jointing and finishing of corten steel and Khavada stone to a flush finish with recommended framework/dry cladding system / clamping system all complete. Maximum Height Upto :4500mm. Rate to include framework/dry cladding system / clamping system required for paneling of both stone and corten steel paneling on concrete wall surface. Size - 1200mm X 1800mm

NS Double Leaf Automatic Sliding Door- Frameless of 2500mm clear opening X 2500mm height - Providing & Fixing of Automatic Sliding Door , Modular Design and customisbale colo with operator dimensions 168mm W x 92mm H x 4.2 Mtr L for max. opening size of 2.0Mtr Wide & Weight capacity for double Leaf Door is 2x80 Kg .Microprocessor Controlled unit will be self learning with adjustable parameters for opening & closing speed, hold open time, reversing when obstacles are encountered. Operator will have 65W DC brush-less Motor, international Make Timing Belt. Operator can be intgrated with Microwave Sensor / Presence Detector Sensor / Foot Switch Sensor / Handwave sensor, Safety Beam (Light Barrier), Programmable Remote Control to Set different modes & Automatic Locking Mechanism, RFID / Biometric / Fingerprint / Access Card Control System & Push Button. Inclusive all necessary fixing hardwares Cost includes the concelaiment of wire from the source to the mechanism of automation. This also includes the Providing and fixing of 12mm thk toughened glass of make Saint Gobin/Modi/Asis/eqv for automated sliding door with framework and hardware as per drawing.Rate to be quoted shall include the cost of all the fixing hardwares screws/nutts/bolts/screws/uv glue/ required for the fixing with Automated sliding door machine with water and air proofing using appropriate materials and hardware.( hardware , hinges, handles, door stopper, locks ). The exact size of the glass to be checked as per the site and the shop drawings should be approved by the design consultant. Additional casing , with top cover duly painted with exterior grade duco of 5 year warranty for the automation machine should be included in the cost to to prevent dust and water getting in. Make - Dorma/Hafle/Hettich/Geze and

NS Flush Doors- single leaf Size - 1200mmX2500mm - Providing and fixing of single leaf flush door made in block board of 35 mm thickness of approved make, including with door frame size 125mm x 75mm made of seasoned wood, fixed in line & level with necessary hardware, hinges, pivots etc all complete to make it functional. The rate is inclusive of applying 1mm thk teak veneer on both sides, duly polished with melamine finish, fixed with adhesives for strength. Size of door 1200mm X 2500mm. Providing and fixing of custom made door handles of material Wood/MS of desired size and shape as per the design intent finished in polish/paint/duco/powdercoat etc approved by the museum design consultant. The cost is also inclusive of fixtures, screws, hardware, adhesives etc all complete as per the direction of engineer incharge

NS Type 9 - Single leaf- manual sliding door - metal - 1500x2500 mm - Providing and fixing of manually opening wooden/metal sliding partition with provision to accommodate acoustic material. Top cover to be metal sheet/ metal finish/ micro-topping/ metal laminate. Size of the door 1500 X 2500mm. Height of the door to be variable as per lintel level on site.

NS Type 3 - Flush doors- Double leaf - 2000x2500 mm - Providing and fixing of Flush door with double leaf,having wooden plywood base of 25-35mm thick with laminate/duco/microtopping of approved shade on both sides, fixed with complete necessary hardware ( hardware , hinges, handles, door stopper, locks ). The door to include all the necessary hardware/accessories required for a pivot opening detail. Size of door 2000mm X 2500mm. Height of the door to be variable as per lintel level on site.

NS Foot Rail - Providing and fixing of foot rail of height 150mm, heavy gauge stainless steel pipe of diameter50mm made in stainless steel

NS Flush Doors- single leaf Size - 1000mmX2500mm - Providing and fixing of single leaf flush door made in block board of 35 mm thickness of approved make, including with door frame size 125mm x 75mm made of seasoned wood, fixed in line & level with necessary hardware, hinges, pivots etc all complete to make it functional. The rate is inclusive of applying 1mm thk teak veneer on both sides, duly polished with melamine finish, fixed with adhesives for strength. Size of door 1000mm X 2500mm. Providing and fixing of custom made door handles of material Wood/MS of desired size and shape as per the design intent finished in polish/paint/duco/powdercoat etc approved by the museum design consultant. The cost is also inclusive of fixtures, screws, hardware, adhesives etc all complete as per the direction of engineer incharge

NS Flush Doors- single leaf Size - 900mmX2500mm - Providing and fixing of single leaf flush door made in block board of 35 mm thickness of approved make, including with door frame size 125mm x 75mm made of seasoned wood, fixed in line & level with necessary hardware, hinges, pivots etc all complete to make it functional. The rate is inclusive of applying 1mm thk teak veneer on both sides, duly polished with melamine finish, fixed with adhesives for strength. Size of door 900mm X 2500mm. Providing and fixing of custom made door handles of material Wood/MS of desired size and shape as per the design intent finished in polish/paint/duco/powdercoat etc approved by the museum design consultant. The cost is also inclusive of fixtures, screws, hardware, adhesives etc all complete as per the direction of engineer incharge

NS Flush Doors- single leaf Size - 750mmX2500mm - Providing and fixing of single leaf flush door made in block board of 35 mm thickness of approved make, including with door frame size 125mm x 75mm made of seasoned wood, fixed in line & level with necessary hardware, hinges, pivots etc all complete to make it functional. The rate is inclusive of applying 1mm thk teak veneer on both sides, duly polished with melamine finish, fixed with adhesives for strength. Size of door 750mm X 2500mm. Providing and fixing of custom made door handles of material Wood/MS of desired size and shape as per the design intent finished in polish/paint/duco/powdercoat etc approved by the museum design consultant. The cost is also inclusive of fixtures, screws, hardware, adhesives etc all complete as per the direction of engineer incharge

NS Double leaf Glass doors Size - 1500mmX2500mm - Providing and fixing of Double leaf Glass door , made of 12mm thk clear/extra clear toughened glass of approved brand / manufacture and design, including fixing properly with all necessary fittings, arrangement and making necessary holes etc. all complete. The cost is also inclusive of hardware, heavy duty floor spring of approved make with a capacity to support door weight upto 80kgs on both leaves of the door to make it functional all complete as per the direction of site incharge. The cost is inclusive of cutting the surface to install the mechanism flushed to the face of the floor wherever required. The cost is exclusive of providing door handles. Size-1500mm X 2500mm .

NS Flush Doors- double leaf - Providing and fixing of double leaf flush door made in block board of 35 mm thickness of approved make, including with door frame size 125mm x 75mm made of seasoned wood, fixed in line & level with necessary hardware, hinges, pivots etc all complete to make it functional. The rate is inclusive of applying 1mm thk teak veneer on both sides, duly polished with melamine finish, fixed with adhesives for strength. Size of door 1500mm X 2500mm. Providing and fixing of custom made door handles of material Wood/MS of desired size and shape as per the design intent finished in polish/paint/duco/powdercoat etc approved by the museum design consultant. The cost is also inclusive of fixtures, screws, hardware, adhesives etc all complete as per the direction of engineer incharge. (AOR No.RA-28)

NS Flush Doors- double leaf- lacquered glass Size -2000mmX2500mm - Providing and fixing of double leaf flush door made in block board of 35 mm thickness of approved make, including with door frame size 125mm x 75mm made of seasoned wood, fixed in line & level with necessary hardware, hinges, pivots etc all complete to make it functional. The rate is inclusive of providing and fixing on both sides of the door with 6mm thk toughened glass with highly resistant lacquer to one side of the glass of approved make and shade as per colour in specified in detail drawings and as approved by consultant. The rate is inclusive of fixing properly the glass with all necessary silicone adhesives, fittings, arrangement and making necessary holes wherever required etc. all complete as per direction of Engineer in charge. Size of door 2000mm X 2500mm. Providing and fixing of custom-made door handles of material Wood/MS of desired size and shape as per the design intent finished in polish/paint/duco/powdercoat etc approved by the museum design consultant. The cost is also inclusive of fixtures, screws, hardware, adhesives etc all complete as per the direction of engineer incharge.

NS Custom made door handles - Providing and fixing of custome made door handles of material Wood/MS of desired size and shape as per the design intent finished in polish/paint/duco/powdercoat etc approved by the museum design consultant. The cost is also inclusive of fixtures, screws, hardware, adhesives etc all complete as per the direction of engineer incharge.

NS Window glazing - Providing and fixing window fitting having clear/extra clear toughened glass of 12-15mm thickness of approved make fixed on the M.S. section/channel of size 25x25mm/50x50mm with silicone adhesives of approved shade and as per the design detail of the museum design consultant.The assembly to be complete with all the necessary hardware such as the M.S. brackets, anchors, channels, nuts, bolts, rubber fittings/fillers etc all complete as per the direction of engineer in charge. The cost is also to be inclusive of providing desired coats of steel primer/duco/as per requirement on the ms section. The glass to have special film on one side of the opening. The fixing to be such that the M.S. section/ channels will be conealed within the panelling.

NS MS Sheet door (single leaf) - Providing and fixing of MS Metal door with single leaf , including with door frame made of wood/W.P.C and door made in block board , fixed in line & level, with 1-4mm thk M.S Metal sheet/laminate/veneer on both sides, duly finished as per the approval of the museum design consultant, fixed with complete necessary hardware ( hardware , conceled hinges, handles, door stopper, locks ). Size of door 900mm X 2400mm/as per design.

NS Flush Doors- double leaf- lacquered glass Size -1800mmX2500mm - Providing and fixing of double leaf flush door made in block board of 35 mm thickness of approved make, including with door frame size 125mm x 75mm made of seasoned wood, fixed in line & level with necessary hardware, hinges, pivots etc all complete to make it functional. The rate is inclusive of providing and fixing on both sides of the door with 6mm thk toughened glass with highly resistant lacquer to one side of the glass of approved make and shade as per colour in specified in detail drawings and as approved by consultant. The rate is inclusive of fixing properly the glass with all necessary silicone adhesives, fittings, arrangement and making necessary holes wherever required etc. all complete as per direction of Engineer in charge. Size of door 2000mm X 2500mm. Providing and fixing of custom-made door handles of material Wood/MS of desired size and shape as per the design intent finished in polish/paint/duco/powdercoat etc approved by the museum design consultant. The cost is also inclusive of fixtures, screws, hardware, adhesives etc all complete as per the direction of engineer incharge.

NS Server Area Access Door Panels - Providing and fixing of double leaf door. Size of door upto 750mm X 2400mm. 55mm to 72mm thick sandwich type composite sound reducing flush door shutters. The combined assembly set of door frame and door shutters to be as per following details: (a) Door frame shall be of teak / hard wood of size – 110 mm X 100 mm, including making necessary grooves in the frame for fixing of hollow bulb type EDPM gaskets on rebates to block noise leakage from gap in between door frame and shutter. (b) The frame of shutter shall be made from 40 mm thick teak / hard wood stiles and top & bottom rails of size 94 mm and core made of lock rail 100 mm wide and 40 mm thick and three additional strips 50 mm wide and 25 mm thick (minimum) (c) Face panels shall be of 12 mm thick Marine ply boards of approved make conforming to relevant IS codes / International Standards on both sides of the core of the shutter with required primer at the unexposed surface . One side of ply board shall be fixed to the core of the shutter along with a 5 mm thick Neoprene rubber sheet on its inner face. (e) laminate finish as approved on top of 12 mm thick marine plyboard on both face of shutter. Make-merino and (f) Hardware- The door assembly shall be fixed to the door frame with heavy duty stainless steel hardware i.e. Door Lock, SS Bal bearing Hinges , SS door handle ‘D’ type back to back, SS Tower bolt.

NS MS Sheet door ( double leaf) - Providing and fixing of MS Metal door with Double leaf , including with door frame made of wood/W.P.C and door made in block board , fixed in line & level, with 1-4mm thk M.S Metal sheet/laminate/veneer on both sides, duly finished as per the approval of the museum design consultant, fixed with complete necessary hardware ( hardware , conceled hinges, handles, door stopper, locks ). Size of door 1800mm X 2400mm/as per design .

NS Corian door - Providing and fixing of doors made of Mild steel/wood finished with 12mm WPC cladding and 6mm thick UV solid surface grey /colored corian along with proper locking arrangement and as approved by Engineer-in-charge

NS Fire Doors - Providing and fixing of fire exit door of size - 3000mm x 2500mm one side openable with hinges, long click handles as per approved design a) Door Frame: Providing Frames for Lead Lined Fire resistant door shutters 1st class Malaysian Hardwood Frame densified and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 140 X 70 mm with 45mm thick two layered 3mm Lead Line Sheets with 10mm overlap from either side & spray quoted with 2 coats of In tumescent paint of minimum 200 micron, with 1 row of Brush- Type Astroflame® intumescent strip (imported) of size 10mmx4mm concealed in the groove of the Frame for fire and hot and cold smoke sealing, etc. complete as per direction of Engineer in Charge b) Shutter: Providing of 57mm thick asbestos free composite, 'TUFWUD' brand - 3 criteria - fire, heat and smoke check Lead Lined Door Shutter with flame guard of 120 minutes IS3614 part -II comprising of 2x9mm Calcium Silicate boards, Chemical treated internal timber with Fire retardant chemicals in pressure impregnation vessels under 160 PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 frame work of 100x30 mm with 30mm thick infill of ceramic fibre (density 128 Kgs/CMT) vermiculite mix, 3mm thick Lead Sheet on one side faced & 3mm Fire retardant High Density Fibreboard, internally lipped with hardwood beading, and pasted in Hydraulic Press under 50 tonnes pressure, spray quoted with 2 coats of Intumescent paint of minimum 300 micron, and with 1 row of Brush- Type Astroflame® intumescent strip (imported) of size 10mmx4mm concealed for fire and smoke sealing in the grooves in the shutter on all edges except bottom, without any external lipping.

NS Conserved wooden pattern double leaf door - Providing and fixing of vintage collection of doors found in Haryana and nearby regions. As per detail drawing. the doors have to be provided is to be operationational and refurbished as per the approval of the Museum design consultant.

NS Curved Doors - Providing and fixing of cuved flush door with single/double leaf, including door frame made of seasoned wood/W.P.C and door made in block board , fixed in line & level, with teak veneer with printed graphcs over it on both sides,as per the artwork and finished as per the approval of museum design consultant , fixed with complete necessary hardware( conceled hinges, handles, door stopper, locks ). Size of door 900mm X2400mm/as per design

NS TV Panels - Providing and fixing of a wooden T.V. mounting box made of up to 18mm thick plywood with 4-6mm mdf finished in duco paint of approx. size 1700x1000mm/ as per the size of the equipment with provision to fix vision glass as per design detail. Inclusive of the cost of vision glass of thickness 6-12mm. Inclusive of all the necessary fittings, fixtures, required for the installation. The cost is also inclusive of providing & installing 65 inch TV with 4K Resolution, with openable panels. The Rates inclusive of all hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per concept. upto 65inch. Make - Samsung/LG/ /Panasonic

NS Wall mounted Artefact table (600x600mm) - Providing and Fixing of artefact table of size 600x600mm with base made of 50X50mm hollow sections of desired thickness with appropriate spacing and necessary welding at junctions including applying of required coats of steel primer on sections. The cost is inclusive of providing and fixing 12mm thk commercial ply of approved make on MS frame work with necessary hardwares,screws etc all complete. The top to be finished in 12 mm thk corian of approved make and shade fixed to the ply with silicone adhesives including buffing and polishing of the surface as per approved drawings. The corian top will be etched with artwork. The remianing area to be painted in duco of approved shade. a)Providing and fixing of display glass case of 8 M.M thick toughened glass of height 250mm on all four side fixed on 12mm-15mm thk aluminium channels and top placed of size as/specifications/design. The cost is inclusive of fixing of all edges with extra clear silicone with necessary fixtures and allen key locking arrangement (not to be visible on the face) b)Providing and fixing of 6 mm thick white lacquered glass on the top and all four sides of base to place the artefacts with edges bevelled at an angle on all edges as per approved detail drawings fixed to a ply base with extra clear silicone .

NS Wall mounted Artefact table (1200x600mm) - Providing and Fixing of artefact table of size 1200x600mm with base made of 50X50mm hollow sections of desired thickness with appropriate spacing and necessary welding at junctions including applying of required coats of steel primer on sections. The cost is inclusive of providing and fixing 12mm thk commercial ply of approved make on MS frame work with necessary hardwares,screws etc all complete. The top to be finished in 12 mm thk corian of approved make and shade fixed to the ply with silicone adhesives including buffing and polishing of the surface as per approved drawings. The corian top will be etched with artwork. The remianing area to be painted in duco of approved shade. a)Providing and fixing of display glass case of 8 M.M thick toughened glass of height 250mm on all four side fixed on 12mm-15mm thk aluminium channels and top placed of size as/specifications/design. The cost is inclusive of fixing of all edges with extra clear silicone with necessary fixtures and allen key locking arrangement (not to be visible on the face) b)Providing and fixing of 6 mm thick white lacquered glass on the top and all four sides of base to place the artefacts with edges bevelled at an angle on all edges as per approved detail drawings fixed to a ply base with extra clear silicone .

NS Way Finding - Wall Mounted - Providing and Installation of wall mounted Glass Signage of size 750mm x 1200 mm , with Text Etched / vinyl cut letter text on top. Designed as per design given by museum design consultant. Sample to be approved by Museum consultant before production. Way Finding content needs to be approved by museum consultant before production. All necessary hardware for fixing to be considered.

NS Corten Steel wall panelling - Providing and fixing of wall panelling up to ceiling height consisting of Steel / Metal frame work for support finished on top surface with 4mm thk corten steel sheet with CNC cut Artwork in 50% of the area on which paneling is done and backed with 25mm thk stone backing and 10% area with 2 mm SS artwork pated over/under the paneling . Item Rate to include jointing and finishing of corten steel and Khavada stone to a flush finish with recommended framework/dry cladding system / clamping system all complete. Maximum Height Upto :4500mm. Rate to include framework/dry cladding system / clamping system required for paneling of both stone and corten steel paneling on concrete wall surface.

NS Freestanding Artefact table (600x600mm) - Providing and Fixing of artefact table of size 600x600x900 mm with base made of 50X50mm hollow sections of desired thickness with appropriate spacing and necessary welding at junctions including applying of required coats of steel primer on sections. The cost is inclusive of providing and fixing 12mm thk commercial ply of approved make on MS frame work with necessary hardwares,screws etc all complete. The top to be finished in 12 mm thk corian of approved make and shade fixed to the ply with silicone adhesives including buffing and polishing of the surface as per approved drawings. The corian top will be etched with artwork. The remianing area to be painted in duco of approved shade. a)Providing and fixing of display glass case of 8 M.M thick toughened glass of height 250mm on all four side fixed on 12mm-15mm thk aluminium channels and top placed of size as/specifications/design. The cost is inclusive of fixing of all edges with extra clear silicone with necessary fixtures and allen key locking arrangement (not to be visible on the face) b)Providing and fixing of 6 mm thick white lacquered glass on the top and all four sides of base to place the artefacts with edges bevelled at an angle on all edges as per approved detail drawings fixed to a ply base with extra clear silicone .

NS Artifact Display case (1500X1500X2800mm) - Providing 1500X1500X2800mm (LxWxH) Artifact Table Display Unit- Find the details in the attached drawing and the details of international standards mentioned below. Any differnce in size will be taken on prorata basis. a) 150 mm high base of showcase unit of 19mm Ply board finished with 6 mm thick Corian. One side of the base to be openable with all necessary hardware like hinges screws etc complete. b) 900x900x450mm (L x W x H) Pedestal to be made of 19mm Ply board and finished with 8mm thick frosted glass as per drawing. c) 1200mm wide and 2725 mm high 12mm thick toughened clear glass box over Corian base. Glass sides to be fixed with 10-15 mm thick pre factory finished powder coated metal beading on all the edges for support. Three sides to be fixed and one side to be openable with the help of 25x25mm L angle and necessary hardwae like pivot, screws etc complete. The openable shutter to be lockable with allen key lock as per drawing. The above joinery detail should be as sleak as possible and should not disturb the lighting effect from the above. Locking system should not be visible. Reference Image attached. d) Artifacts to be placed by MS painted hooks/Industrial tapes etc. - Reference image attached. e) Clear glass should be used with blended edges as per reference video. f) Cost should include Borer/ Anti termite treatment for plywood. h) Showcase unit to be made complete as per the drawing and details. g) 650x100x3mm thick mild steel sliding Signage finished with matt finish Duco paint and print as per design/ Graphic design. i) Showcase unit to be approved by Engineer-in- charge.

NS Fire Evacuation Plans - Providing and fixing of fire evacuation map signage as per approved fire norms, with acroleic base and reflective vinyl sticker, size 420mmx297mm, fixed with 3m tape, designed as per each location. Location drawings to be approved by museum design consultant. Sample signage and its design to be approved by museum consultant before production.

NS SITC of L Shape Connectors suitable for above track items. (AOR No.RA-03)

NS SITC of Straight Connectors suitable for above track items. (AOR No.RA-04)

NS SITC of Cross Joint suitable for above track items. (only for recessed version) (AOR No.RA-05)

NS SITC of Suspension Cable (only required for suspended version) (AOR No.RA-06)

NS Artifact Display case (2400X1500X2100mm)(LXBXH) - Providing 2400X1500X2100 mm (L x W x H) Artifact Display Unit. Find the details in the attached drawing and the details of international standards mentioned below. Any differnce in size will be taken on prorata basis. (Refer image No. 15 at Page No. 99 for reference only) (Refer image No. 17 at Page 101) a) 900 mm high base of showcase unit of 19mm Ply board finished with 6 mm thick Corian. One side of the base with toughened glass panel (as per design) to be openable with all necessary hardware like channes screws etc complete. b) 2600X900x150 (L x W x H) Pedestal to be made of 19mm Ply board and finished with 8mm thick frosted glass as per drawing. c) 3300x1200mm wide and 1400 mm high 12mm thick toughened clear glass box over Corian base. Glass sides to be fixed with 10-15 mm thick pre factory finished powder coated metal beading on all the edges for support. Glass sides to be fixed with 10- 15 mm thick pre factory finished powder coated metal beading on all the edges for support. Three sides to be fixed and one side to be openable with the help of corian finished panel and necessary hardware like sliding channel, screws etc complete. The openable panel to be lockable with allen key lock as per drawing. Locking system should not be visible. Reference Image attached. d) 2600x100x 3mm thick mild steel sliding Signage finished with matt finish Duco paint and print as per design/ Graphic design. e) Artifacts to be placed by MS painted hooks/Industrial tapes etc. - Reference image attached. f) Clear glass should be used with blended edges as per reference video. g) Cost should include Borer / Anti termite treatment for plywood. h) Showcase unit to be made complete as per the drawing and details. i) Showcase unit to be approved by Engineer-in- charge.

NS Artifact Display case (2400X1500X1650mm)(LXBXH) - Providing 2400X1500X1650 mm (L x W x H) Artifact Display Unit. Find the details in the attached drawing and the details of international standards mentioned below. Any differnce in size will be taken on prorata basis. (Refer image No. 15 at Page No. 99 for reference only) (Refer image No. 18 at Page 102) a) 150 mm high base of showcase unit of 19mm Ply board finished with 6 mm thick Corian. One side of the base with toughened glass panel (as per design) to be openable with all necessary hardware like channes screws etc complete. b) 2600X900x600 (L x W x H) Pedestal to be made of 19mm Ply board and finished with 8mm thick frosted glass as per drawing. c) 3000x1200mm wide and 1500 mm high 12mm thick toughened clear glass box over Corian base. Glass sides to be fixed with 10-15 mm thick pre factory finished powder coated metal beading on all the edges for support. Three sides to be fix and one side to be openable with the help of corian finished panel and necessary hardwae like sliding channel, screws etc complete. The openable panel to be lockable with allen key lock as per drawing. Locking system should not be visible. Reference Image attached. d) 2450x100x 3mm thick mild steel sliding Signage finished with matt finish Duco paint and print as per design/ Graphic design. e) Artifacts to be placed by MS painted hooks/Industrial tapes etc. - Reference image attached. f) Clear glass should be used with blended edges as per reference video. g) Cost should include Borer / Anti termite treatment for plywood. h) Showcase unit to be made complete as per the drawing and details. i) Showcase unit to be approved by Engineer-in- charge.

NS Artifact Display case (1400X475X1500mm)(LXBXH) - Providing 1400X475X1500 (WxDxH)mm Artifact Display Unit for wall. Find the details in the attached drawing and the details of international standards mentioned below. Any differnce in size will be taken on prorata basis a) 75 mm high base of showcase unit of 19mm Ply board finished with 6 mm thick Corian. b) 1050x 150X 925 (WxDxH) Pedestal to be made of 19mm Ply board and finished with 8mm thick frosted glass as per drawing. c) 1250x350x1350mm (WxDxH) Toughened glass box shutter with 75x100mm 19mm thick Ply board frame(as per design)to be openable with all necessary hardware like heavy duty Stainless Steel Hydraulic Hinges, screws etc complete. Glass sides to be fixed with 10-15 mm thick pre factory finished powder coated metal beading on all the edges for support. The openable panel to be lockable with allen key lock. Locking system should not be visible. Reference Image attached. d) 950x100x 3mm thick mild steel sliding Signage finished with matt finish Duco paint and print as per design/ Graphic design. e) Artifacts to be placed by MS painted hooks/Industrial tapes etc. - Reference image attached. f) Clear glass should be used with blended edges as per reference video. g) Cost should include Borer / Anti termite treatment for plywood. h) Showcase unit to be made complete as per the drawing and details. i) Showcase unit to be approved by Engineer-in- charge.

NS Artifact Display case (1800X500X2400mm)(LXBXH) - Providing 1800X500X2400 (WxDxH)mm Artifact Display Unit for wall. Find the details in the attached drawing and the details of international standards mentioned below. Any differnce in size will be taken on prorata basis. a) 150mm high base & 1775x288x75mm back side panel of showcase unit of 19mm Ply board finished with 6 mm thick Corian. b) 1525X 2550 x75 (WxHxD) Pedestal to be made of 19mm Ply board and finished with 8mm thick frosted glass as per drawing. c) 1725x425x2575mm (WxDxH) Toughened glass box shutter with 75x100mm 19mm thick Ply board frame (as per design) to be openable with all necessary hardware like heavy duty Stainless Steel Hydraulic Hinges, screws etc complete. Glass sides to be fixed with 10-15 mm thick pre factory finished powder coated metal beading on all the edges for support. The openable panel to be lockable with allen key lock. Locking system should not be visible. Reference Image attached. d) 1325x 100x 3mm thick mild steel sliding Signage finished with matt finish Duco paint and print as per design/ Graphic design. e) Artifact Display Unit to be fix on the wall with the help of necessary hardware like screws. chemical fastener etc. all complete. f) Artifacts to be placed by MS painted hooks/Industrial tapes etc. - Reference image attached. g) Clear glass should be used with blended edges as per reference video. h) Cost should include Borer / Anti termite treatment for plywood. i) Showcase unit to be made complete as per the drawing and details. j) Showcase unit to be approved by Engineer-in-charge.

NS Fire Signages - Providing and fixing of fire signage as per approved fire norm symbol, with acroleic base and reflective vinyl sticker , size 150mm x 150mm , fixed with 3m tape. Location drawings to be approved by museum design consultant. Sample signage and its design to be approved by museum consultant before production.

NS NON reflective Glass - Providing and fixing of 12mm toughenend non reflective glass.

NS Extra Clear Glass - Providing and fixing of 12mm toughenend extra clear glass, with screen printing

NS Stone - Providing and fixing of 20mm Thick stone on counter top and moulding of edges as per design cost inlcuding all the hardware required for fixing of stone.

NS Glass Print Graphic Panels - Designing, Providing and Installation of 12mm thk toughened glass Info - Graphic glass panel of size 1200mm x 4500mm, mounted on on museum interior walls fixed on the wooden batten frame of section 100mmX50mm at 600mm c/c both ways and 12mm thick BWR grade plywood of Greenply/Century ply or similar makes on front side with all the necessary hardware's used to fix the Canvas , inclusive of custom designed Printed text and graphics Printed text and graphics as per requirement of the gallery design and conceptual design given by museum design consultant. The Glass panel has to be backlit, with appropriate acrylic backing and LED light fixture with drivers and all necessary hardware. The Backlit boxing should be able to diffuse sharp LED glare from light fixtures. Content and panel design needs to be approved by museum consultant before production. All prints will be done 1/32” - 1/8” from the edge of the glass to prevent contamination and consequential defects resulting from overspray. Choose high quality image from reliable source (min. 2500 pixels) for the best results • Check quality in Photoshop at 100% scale (proportionate to actual size desired) • Consider the viewing distance for the graphics • Complete print test (scale to final size, print small crop, apply patterns, view at actual distance, adjust) • Request a Sample Print from vendor if unsure of the expected results • Image quality impacts final image result: Image resolution is pixel data image holds, therefore the higher the resolution, the more detail the image will have. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English as per conceptual design provided by Museum consultant.

NS Fabric /Canvas Print Graphic Panels - Designing, Providing and Installation of Fabric / Canvas Print Info - Graphic panel of size 1200mm x 4500mm, mounted on on museum interior walls fixed on the wooden batten frame of section 100mmX50mm at 600mm c/c both ways and 12mm thick BWR grade plywood of Greenply/Century ply or similar makes on front side The wooden framework will have 1" cushioning on top that will be finished on top Canvas print graphic inclusive of all the necessary hardware's used to fix the Canvas , inclusive of custom designed Printed text and graphics Printed text and graphics as per requirement of the gallery design and conceptual design given by museum design consultant. The Fabric / Canvas Print panel has to be backlit, with appropriate acrylic backing and LED light fixture with drivers and all necessary hardware. The Backlit boxing should be able to diffuse sharp LED glare from light fixtures. Content and panel design needs to be approved by museum consultant before production. All prints will be done 1/32” - 1/8” from the edge of the glass to prevent contamination and consequential defects resulting from overspray. Choose high quality image from reliable source (min. 2500 pixels) for the best results • Check quality in Photoshop at 100% scale (proportionate to actual size desired) • Consider the viewing distance for the graphics • Complete print test (scale to final size, print small crop, apply patterns, view at actual distance, adjust) • Request a Sample Print from vendor if unsure of the expected results • Image quality impacts final image result: Image resolution is pixel data image holds, therefore the higher the resolution, the more detail the image will have. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English, , as per conceptual design provided by Museum consultant.

NS Corten Steel Information Panels - Providing and Installation of 4mm thk Corten steel Info - Graphic panel of size 1200mm X 3800mm , fixed with Corten Steel/MS Framework with artwork in Stainless steel and Corten Steel etching on top. Stainless Steel to be fixed on Corten Steel with necessary chemical adhesives. MS Frame structure to include cost of CNC, Raw Material, waterjet/laser/plasma cutting, Spacer, Chemical Fasteners, Grinding .The structure to be supported with Ms tubular section and base plate and fastened withi fastener and structurally approved, with required foundation work as per approved structure design. Content to be designed on the basis of conceptual design given by museum design consultant. Content and panel design needs to be approved by musuem consultant before production. For the purposed of costconsideration, consider the area for Stainless steel, as 50% the area of corten steel. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English, , as per conceptual design provided by Musuem consultant.

NS Free standing Glass Information Panels - Providing and Installation of Information Glass Panels, with text etched / plotter vinyl text on 12 mm thk toughened glass, 2 No. glass panels to be included in one unit for structural stability, of size 1200mm in width and 2400mm in height , fixed on 12mm thk acrylic solid surface base as per drawing. Sample Information Panel and its content and design needs to be approved by museum consultant before production. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English, , as per conceptual design provided by Museum consultant.

NS Free standing Glass Information Panels Angular - Providing and Installation of Information Glass Panels in custom Angular shape as per drawing, with text etched / plotter vinyl text/ Glass Printing on 12 mm thk toughened glass, 2 No. glass panels to be included in one unit for structural stability , of size 1200mm in width and 1800mm in height , fixed on 12mm thk acrylic solid surface base as per drawing. Sample Information Panel and its content and design needs to be approved by museum consultant before production. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English as per conceptual design provided by Museum consultant.

NS Freestanding Graphic panels - Providing and Installation of Information Glass Panels, with text etched / plotter vinyl text on 12 mm thk glass, 2 No.s glass panels to be included in one unit for structural stability , of size 3000mm in width and 1000mm in width, fixed on 12mm thk acrylic solid surface base as per drawing. Content to be designed as per conceptual design given by Museum Design Consultant. Sample Information Panel and its content and design needs to be approved by museum consultant before production. Refer drawing no. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English as per conceptual design provided by Museum consultant.

NS Glass Print Graphic Panels (Backlit) - Designing, Providing and Installation of 12mm thk toughened glass Info - Graphic glass panel of size 1200mm x 4500mm, mounted on on museum interior walls fixed on the wooden batten frame of section 100mmX50mm at 600mm c/c both ways and 12mm thick BWR grade plywood of Greenply/Century ply or similar makes on front side with all the necessary hardware's used to fix the Canvas , inclusive of custom designed Printed text and graphics Printed text and graphics as per requirement of the gallery design and conceptual design given by museum design consultant. The Glass panel has to be backlit, with appropriate acrylic backing and LED light fixture with drivers and all necessary hardware. The Backlit boxing should be able to diffuse sharp LED glare from light fixtures. Content and panel design needs to be approved by museum consultant before production. All prints will be done 1/32” - 1/8” from the edge of the glass to prevent contamination and consequential defects resulting from overspray. Choose high quality image from reliable source (min. 2500 pixels) for the best results • Check quality in Photoshop at 100% scale (proportionate to actual size desired) • Consider the viewing distance for the graphics • Complete print test (scale to final size, print small crop, apply patterns, view at actual distance, adjust) • Request a Sample Print from vendor if unsure of the expected results • Image quality impacts final image result: Image resolution is pixel data image holds, therefore the higher the resolution, the more detail the image will have. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English as per conceptual design provided by Museum consultant.

NS Corten Steel Information Signage - Providing and Installation of 8mm thk Corten steel Info - Graphic panel of size 2400mm X 1200mm , fixed with Corten Steel/MS Framework with artwork in Stainless steel and Corten Steel etching on top. Stainless Steel to be fixed on Corten Steel with necessary chemical adhesives. MS Frame structure to include cost of CNC on 75% of the area , Raw Material, waterjet/laser/plasma cutting, Spacer, Chemical Fasteners, Grinding .The structure to be supported with Ms tubular section and base plate and fastened withi fastener and structurally approved, with required foundation work as per approved structure design. Content to be designed on the basis of conceptual design given by museum design consultant. Content and panel design needs to be approved by musuem consultant before production. For the purposed of costconsideration, consider the area for Stainless steel, as 25% the area of corten steel. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English as per conceptual design provided by Musuem consultant.

NS Free standing Glass Information Panels - Providing and Installation of Information Glass Panels, with text etched / plotter vinyl text on 12 mm thk toughened glass, 2 No. glass panels to be included in one unit for structural stability , of size 900mm in width and 1200mm in height , fixed on 12mm thk acrylic solid surface base as per drawing. Sample Information Panel and its content and design needs to be approved by museum consultant before production. Inclusive of Print ready designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English as per conceptual design provided by Museum consultant.

NS SITC of End Cap required for above Track items. (AOR No.RA-08)

NS SITC of Track Supply End Cap . (AOR No.RA-09)

NS Frosted Film - Supply and installation of Frosted PVC Vinyl , 3M/eqv vinyl with 1 year warranty on printing, plotting and material , with designed graphics , illustrations / artwork and Copywriting and editing of textual content in Hindi, English,as per approved conceptual design. The cost is to be inclusive of custom designed graphics / 2D artwork , illustrations / artwork and Copywriting and editing of textual content in Hindi, English,as per conceptual design and approval of museum design consultant.

NS Granite cobblestone - Providing and fixing at work site, Dark grey/Black color granite/Basalt Cobble Stone with Sandblast Leather Finish of customised size of 100x100x100 mm for Flooring with tolerance not exceeding 10mm & having density of 2800-3000 kg/cum, Including Sand bed 30 mm thick & 1:4 C.M. cement mortar for filling joints ,pointing with cement over joints Curing cleaning complete in all respect and loading, unloading, transportation and including all other taxes and excluding GST complete as directed by Engineer In charge etc.

NS Bench- corian - Providing and fixing of backless curved/straight bench in 12 mm bendable Acrylic solid surface finish of approved shade and make of size - 450mm width x450mm height with desired length as per the space and as per the approved detail drawings. The bendable acrylic solid surface should be be backed with appropriate MS structure 50X50 mm hollow sections of desired thickness with necessary welding at junctions. The cost is inclusive of proving and fixing 12mm thk flexible/normal ply of approved make with necessary hardware, screws etc all complete as per the direction of engineer in charge. The cost should also be inclusive of all necessary adhesives, grinding, buffing etc for installation of bendable acrylic solid surface on the base. Sample bench to be approved by Museum Design Consultant. The bench should also have a 2D/3D graphic as a museum branding or as per the design language of the space.

NS Lacquered Glass (for Wall panelling) - Providing and fixing of 6mm to 12mm thk toughened glass with highly resistant lacquer to one side of the glass of approved make and shade as per colour in specified in detail drawings and as approved by consultant. Rate quoted shall be inclusive of bevelling all the edges at specified angle as per requirement. The rate is inclusive of fixing properly with all necessary silicone adhesives, fittings, arrangement and making necessary holes wherever required etc. all complete as per direction of Engineer in charge.

NS Metal ceiling - Providing and fixing of suspended ceiling with metal plates of varying shapes and sizes such as 1000x1000mm, 1500x1500mm, 3000x3000mm, or as per the design proposal, in approved color and texture by the museum design consultant. Thickness of the metal sheet to be approriate to avoid bending and folding of the sheet and as approved by the museum design consultant. The metal sheets to be suspended with the main slab with a ceiling suspension system designed to withhold the weight of the metal sheets ensuring visitor safety and stability of the ceiling.

NS SITC of approx. 5~10 watt/ mtr; LED strips RGBW Color suitable for Cove Light applications. To have color Temperature of 3000K~6000K; with 50mm LED Cut point and 3 Step Macadam. Securely mounted on aluminium channel with lens / diffuser/ silicon gel etc as per requirment. Complete with DALI driver, mounting bracket / clamp accessories etc as required. 230V, WW. Make : iBL / Led Linear/ iGuzzini (AOR No.RA-24)

NS Lift interiors - Providing and fixing of artwork in materials such as lacqured glass, stone, mdf, metal as per design. The base to be of 75 mm thick mounted paneling with minimum 50X50mm/75 x 75 mm wooden batten in a grid pattern at 600 mm c/c both ways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions with screws, nails, adhesives etc all complete. The cost to be inclusive of top cover of 12 mm commercial plywood BWR grade of Greenply/Centaury ply or similar makes on front side with edge profiles, beadings s etc. The wooden section to be coated with one to two required coats of anti termite solvent and wooden battens used should be good quality wood. The cost is inclusive of fixing the wooden frame structure on floor/wall/ ceiling with necessary adhesives, hardwares, fastners, fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete as per approved design. The cost includes scrapping and levelling the surface for the application of two or more coats of primer to prepare a smooth base for the application of media as per the satisfaction of engineer in charge.

NS SITC of 1.0 Mtr track made from extruded aluminium. Surface/ Suspended/ Recessed mounted (shall be as per final rcp & consultant/ client approval). 6 wires are housed in the track. 4 for three-phase operation, 2 for DALI operation. The wires are enclosed in rigid extruded profiles made of insulating material with high dielectric strength. Length - 1 metre. 3 phase wires with a common neutral form 3 distinct circuits allowing for 3 separate switching circuits. Maximum applicable load is 16A (3500VA) FELV when the track is connected to mono-phase mains; 2X1A for DALI contacts. Connection to a three-phase mains power supply allows for an overall load of 16A (10500VA), DALI 2X1A (100VA) FELV. Mounting accessories as included as per site requirement. Make : ERCO / Fagerhult/ iGuzzini (AOR No.RA-01)

NS SITC of Fixed round mini-recessed luminaire with contact frame with approx 2W in 2700K/3000K minimum 120lm CRI90. The LED is set back to minimize direct glare. The recessed body is made of machined aluminium and the inside of the ring of thermoplastic available in a range of painted and metallised finishes. PMMA - spot (14°) or medium (25°) high resolution optic lens. The luminaire to have the availability of either Narrow Beam Optic 14° or to have the Medium Beam Optic of around 24° required as per the consultant approval. Complies with EN60598-1 and pertinent regulations. Lifetime > 50,000h - L80 - B10 (Ta 25°C) Fixture should have an option of White, Black finish or combined white black finish. Make: ERCO/ iGuzzini Laser/ Fagerhult (AOR No.RA-18)

NS SITC of InGround/ concrete embeded Uplighter with 5W internal reflector for options of Very Narrow, Narrow, Medium, Flood, and Wide Flood Optics in Color Temperature option (3000K /6000K). The Housing of the luminairre is die castinf darkgrey powder coated aluminium adhesion od ISO Class1/ATM Class 4B The fixture Luminance is 555lm. With Front Cover: hard chrome plated stainless steel SUS 316L and Optical Reflector efficiency >90%. Option to have Direct 220V AC Mains supply or with the Remote driver application. IP67 Fixture with optional Honeycomb Louver Accessory. Make: Eurolite/ We-ef/ iGuzzini (AOR No.RA-23)

NS SITC of 2.0 Mtr track made from extruded aluminium. Surface/ Suspended/ Recessed mounted (shall be as per final rcp & consultant/ client approval). 6 wires are housed in the track. 4 for three-phase operation, 2 for DALI operation. The wires are enclosed in rigid extruded profiles made of insulating material with high dielectric strength. Length - 2 metre. 3 phase wires with a common neutral form 3 distinct circuits allowing for 3 separate switching circuits. Maximum applicable load is 16A (3500VA) FELV when the track is connected to mono-phase mains; 2X1A for DALI contacts. Connection to a three-phase mains power supply allows for an overall load of 16A (10500VA), DALI 2X1A (100VA) FELV. Mounting accessories as included as per site requirement. Make : ERCO / Fagerhult/ iGuzzini (AOR No.RA-02)

NS SITC of Ceiling mounted base /Track Mounted with adapter adjustable LED spot light fixture with 28W in 3000K CRI90 having net lumen output of 2700m. LED's should be from MacAdam Step:2. Fixture should have an option of Spot, Flood and Wide Flood optics. as per approval. Luminaire's three-phase adapter for electrified tracks or base should be made of die-cast aluminium and thermoplastic material. Anti scratch reflector made of PVD aluminium that can provide optimum performance in terms of Lighting efficiency with Flood Optics and having a possibility of istalling a flat accessory like a glass cover or an elliptical distribution refractor, The product has the capability of having interchangable reflectors for medium flood and wide flood that can be ordered as accessories. Life of LED should be > 50,000h - L90 - B10 (Ta 25°C). Overvoltage protection: 2kV Common mode & 1kV Differential mode. Fixture should have an option of White, Black finsih as per site requirement. Option of installing a range of accessories including an Elliptical Lens, Soft Lens, Glass Cover and option of replacing internal reflector. Diameter of the fixture should not be more than 100mm.Complies with EN60598-1 and pertinent regulations and should be BIS certified Make: ERCO/ iGuzzini Front Light / Fagerhult (AOR No.RA-10)

NS SITC of approx. 12~19 watt / mtr; 4 in 1 ; LED strips RGBW Color suitable for Cove Light applications. To have 100mm Cut intervals and 16.7mm LED Pitch. Securely mounted on aluminium channel with Clear lens / diffuser etc as per requirment. Complete with DIMMABLE driver, mounting bracket / clamp accessories etc as required. 230V, WW. Make : iBL/ Led Linear/ iGuzzini (AOR No.RA-25)

NS SITC of Spike Light with 6W for options of Very Narrow, Narrow, Medium, Flood, and Wide Flood Optics in Color Temperature option (3000K /6000K). The Housing of the luminairre is die casting darkgrey powder coated aluminium adhesion of ISO Class1/ATM Class 4B The fixture Luminance is 740 lm. With Front Cover: hard chrome plated stainless steel SUS 316L and Optical Lens efficiency >80%. Fixture to have Direct 220V AC Mains supply. IP67 Fixture with Basic and Secondary Color Options. Make: Eurolite/ We-ef/ iGuzzini (AOR No.RA-28)

NS SITC of IP65, wall Recessed luminaire, step light, in circular or square shape with PUK LED giving asymmetric beam. The Fixture is Ideal for wall-mounted, low-level night light. Colour temperatures includes 2700k, 3000k and 4000k. Direct 220V application with no additional driver requirement The Fixture uses 4W AC. Asymmetrical flood beam of 105°. The Fixture Dimensions are not to exceed 65mm in diameter and 40 mm in depth. IP66 Outdoor Rated Fixture. Make: IBL/ iGuzzini/ we-ef/ Eurolite (AOR No.RA-29)

NS SITC of Track mounted adjustable LED spot light fixture with approx 22W in, 3000~4000K CRI90 having net lumen out of 1658lm. LED's should be from McAdam Step:2. Fixture should have an option of Super Spot, Medium, Flood and Wide Flood optics. (as per approval) . Indoor adjustable spotlight in Circular or Square design with adapter for installation on a three-phase/DALI track. Device made of die-cast aluminium and a front part made of a thermoplastic material. Spotlight double adjustability allows a 360° rotation about the vertical axis and 90° tilting relative to the horizontal plane. with OPTIBEAM LENS technology and a well-defined spot light beam. Life of LED should be > 50,000h - L80 - B10 (Ta 25°C). Overvoltage protection: 2kV Common mode & 1kV Differential mode. Product complete with DALI dimmable driver. Fixture should have an option of White, Black finish as per site requirement. Fixture should not be more than ?130mm and 165 mm height. Option of installing a range of flat accessories including an OPTIBEAM REFRACTOR for varying light distribution, an elliptical distribution refractor, a louver, a soft lens and an outdoor accessory like an asymmetric visor for eliminating stray light dispersion on the ceiling. Complies with EN60598-1 and pertinent regulations and should be BIS certified. Make: ERCO/ iGuzzini View Opti beam lens / Fagerhult (AOR No.RA-11)

NS SITC of track mounted adjustable LED WALL WASHER spot light fixture with approx 34W in 3000K CRI 80 having net lumen out of 2280lm. LED's should be from McAdam Step:2. Indoor adjustable spotlight in Square design with adapter for installation on a three-phase/DALI track or to have accessoriy for standalone installation as surface mounted or ceiling recessed. Product complete with super pure anodized aluminium reflector to guarantee wall washer light distribution for vertical downlight wall illumination. DALI ballast integrated in the body. Die-cast aluminium optical assembly. Rotates 360° about the vertical axis and tilts 90° relative to the horizontal plane. Passive heat dissipation. Option of installing an accessory asymmetric screen. Life of LED should be > 50,000h - L80 - B10 (Ta 25°C). Overvoltage protection: 2kV Common mode & 1kV. Differential modeFixture should have an option of White, Black finish as per site requirement. Fixture should not be more than 170mm width and 165 mm in height. Option for installation of accessory like an asymmetric visor for eliminating stray light dispersion on the ceiling. Complies with EN60598-1 and pertinent regulations and should be BIS certified. Make: ERCO/ iGuzzini View Opti Linear Lens WW/ Fagerhult (AOR No.RA-12)

NS SITC of Pendant luminaire with with HPE (High Performance Efficiency) LED, system power: 20 W, luminous flux of luminaire 2100 lm, Colour temperature of 4000 K, Neutral white, CRI > 80, 230V constant current driver, 70% of luminous flux after 50,000 operating hours; Energy efficient LEDs, Direct light emission, Luminaire housing in aluminium, Polyester powder black coloured coat applied over a 5- stage pre-treatment, Opal diffuser for a homogenous light distribution ZHLS (Zero Halogen Low Smoke) internal wiring, Electronic dali control gear, Protection class I, IP 20, Ø = 427 mm, H = 227 mm PL =1500 mm. Make: Wipro / Signify / Regent (AOR No.RA-30)

NS SITC of standalone ceiling recessed /surface mounted Miniaturised adjustable profiler projector of 6.5W in 3000K/2700K CRI90, Macadam step 3,Die-cast aluminium technical body for LED lamp; high definition OptiBeam reflector. The aluminium optical assembly includes a sophisticated telecentric optic system consisting of four anti-reflection treated glass lenses. Black anodised aluminium locknut for manual focusing. The innovative optic system, combined with the option of manual adjustment and four shaping flaps provides sharp and precise wall illumination with no halo effects or soft edges. The optical assembly is secured to the technical body with a rapid and practical magnetic system; this solution allows the unit to be rotated by 360° which considerably increases its versatility. The projector is designed to obtain a square, rectangular or variously irregular beam by manoeuvring the flaps. Fixture should have option of two gobos for different diameters of circular shapes. The swivel joints allow the spotlight. to be rotated by 359° and tilted by 90°. Lifetime > 50,000h - L80 - B10 (Ta 25C). Remote Constant current driver required. Fixture should have Diameter fo the fixture should not exceed 40mm. Complies with EN60598-1 and pertinent regulations and should be BIS certified. Make: ERCO/ iGuzzini Palco Framer / Fagerhult (AOR No.RA-13)

NS SITC of track mounted Miniaturised adjustable Spotlight projector with adapter of 25W in 3000K/2700K CRI97, Macadam step 2,Die-cast aluminium technical body for LED lamp with 360° rotation around the verticle acis and the possible tilt between +10° and 90° in relation to the horizontal plane. The aiming performance is with mechanical screw locking mechanism with graduated scales and cluth devices. The luminaire is customized with 30mm-40mm metal gobo for round shapes without any halo effect of soft edges. Also special metal flaps are fitted to easily shape and regulate the light beam into squares, rectangles. Accessories should be available that can be adjusted from 2.5mm to 40mm and customised metal gobos. Lifetime > 50,000h - L90 - B10 (Ta 25C). The fixture should not exceed the diameter of 100mm. Complies with EN60598-1 and pertinent regulations and should be BIS certified. Make: ERCO/ iGuzzini Palco Framer/ Fagerhult (AOR No.RA-14)

NS SITC of approx.20~ 24 Watt Surface mounted type 4 feet Batten LED fixture made up of extruded polycarbonate housing, fixture should have minimum net efficacy at System level (Not Chip Level)=100lumens/watt, nominal system lumen of 2000 lumens, Life of fixture 50000hrs @ L70 Lumen maintenance, CCT 4000 - 6000K, CRI=80, PF>0.95, and suitable for 230V AC, 50Hz. supply. Minimum Internal Surge Protection=2.5KV. LED driver shall be BIS registered & luminaire manufacture shall provide LM79report from NABL accredited lab & LM80 report issued by LED manufacturer. Make: Wipro / Signify / Regent (AOR No.RA-33)

NS SITC of Pendant / Surface / Recessed luminaire with HE-High Efficiency LED system power: 26W, luminous flux of luminaire 2860 lm, colour temperature of 5700K, cool white, CRI>80, 230V constant current driver, 70% of luminous flux after 50,000 operating hours, energy efficient LEDs, direct light emission, White powder coated luminaire profile, satin diffuser for a homogenous light distribution, ZHLS(ZERO HALOGEN LOW SMOKE) Internal wiring, with Integral electronic dali control gear. Protection class I, IP40. L = 1175 mm, B = 52 mm, H = 64 mm. Make: Wipro / Signify / Regent (AOR No.RA-34)

NS SITC of ceiling recessed adjustable LED light fixture with Contact Frame of 9.9 W in 3000K CRI90 having net lumen out of approx. 1000lm. LED's should be from McAdam Step:2. Fixture should have an option of Medium, Flood and Wide Flood optics to choose from. Adjustable version that rotates internally by 355° and tiLumenPulse by a maximum of 30°. The swivel unit rotates in a set back position in relation to the surface of the ceiling in order to guarantee precise, comfortable light diffusion and reduce direct glare significantly. The swivel unit body is made of die-cast aluminium with a radiant surface that guarantees optimum heat dissipation. Metallised, thermoplastic, high definition reflector - should have options of Narrow beam, Medium (28Deg) or Flood. Structure with die-cast aluminium external contact frame with a single white finish. Steel rotating parts. Safety glass included Quick and easy tool free assembly. Diameter of the fixture should be 104mm including contact frame with height of the fixture 96 mm. Fixture should be compatible with dimming protocol of DALI/Analog/Triac/DMX. Fixture should have an option of White, Black finish and Internal frame should have option of White, Black, Gold, Chrome, Burnished Chrome options as per site requirement. Complies with EN60598-1 and pertinent regulations and should be BIS certified. Life of LED should be > 50,000h - L90 - B10 (Ta 25°C) Make: ERCO/ iGuzzini Laser Adjustable / LTS (AOR No.RA-15)

NS SITC of Round/ square recessed luminaire with contact frame with approx 16W in 3000/4000K with net delivered lumen at least 1800lm. The LEDs are set a long way back to minimize glare and guarantee a high level of visual comfort. The main body is made of die-cast aluminium with a radiant surface that guarantees optimum heat dissipation. Metallised, thermoplastic, high definition reflector - with the option of Medium, Flood, wideflood optic. The internal ring is made of thermoplastic available in a range of painted and metallised finishes.The diameter of the fixture should be 104mm with the contact frame. The Safety glass should be included with Quick and easy tool free assembly. High color rendering CRI 90 index 3000K LED. The fixture to support all possible Dimming Protocols DALI / Triac / Analog / DMX and to have optional reflectors accessories for elliptical distribution, diffuser glass, honeycomb louvre or decorative rings. Complies with EN60598-1 and pertinent regulations Lifetime: > 50,000h - L80 - B10 (Ta 25°C). Fixture should have an option of White, Black finish and Internal frame should have option of White, Black, Gold, Chrome, Burnished Chrome options as per site requirement. Make: ERCO/ iGuzzini Laser/ Fagerhult (AOR No.RA-16)

NS SITC of approx 10~15 watt, ww, Decorative Suspended/wall mounted Light made of with customised design. Assembled with required light fixtures wiring and all the nesseccary hardwares, intergration, electrical &mechanical elements. Make: Customized with design & detailed shop drawing as approved by Consultant. (AOR No.RA-35)

NS SITC of approx 10~15 watt, ww, Decorative Suspended Light of estimated size with height 300mm (approx.), made out of local stone/concrete/terrazo/corian incorporated while moulding is customized shape as per approved design. Assembled with required light fixtures wiring and all the nesseccary hardwares, intergration, electrical &mechanical elements. Make: Customized with design & detailed shop drawing as approved by Consultant. (AOR No.RA-36)

NS SITC of Round/ square recessed luminaire with contact frame and 15W in 3000K/4000K in net delivered lumen output of more than 1000 lm. LEDs should be McAdam Step 2. Fixed Wall Washer version: the optic system is designed to aim the light flow on a vertical surface with no shadow zones and a precise outline. The main body is made of die-cast aluminium with a radiant surface that guarantees optimum heat dissipation. Structure with die-cast aluminium external contact frame with a single white finish. The diameter of the fixture is 104 mm including the contact frame. The optic unit includes two shaped metallized thermoplastic reflectors, a PMMA refractor/safety screen and a plastic anti-glare casing available in a range of painted and metallised finishes. Quick and easy tool free assembly. High color rendering index 3000K LED. To be compatible with : ON-OFF / 1-10V dimmable / DALI dimmable / Trailing Edge dimmable and the recessed fitting includes a cable and quick coupling connector. Complies with EN60598-1 and pertinent regulations. LED Lifetime > 50,000h - L80 - B10 (Ta 25°C). Make: ERCO/ iGuzzini Laser/ Fagerhult (AOR No.RA-17)

NS SITC of Fixed Ring Ceiling Recessed luminaire with 18 optical elements for LED lamps - with approx 36W in 3000/4000K CRI90 minimum. The optic system guarantees a high level of visual comfort and no glare. The body includes a radiant surface made of die-cast aluminium. Version includes a perimeter surface frame. High definition reflectors made of thermoplastic material vacuum-metallised with aluminium vapours, integrated in a set-back position in the antiglare screen. Supplied with a power supply unit connected to the luminaire. The fixture should not have dia more than 180mm and depth more than 45 mm. Luminaire should accept all Dimming protocols. The Ring Luminaire should have the availabiility to incorporate in addition to itself profiler projector or adjustable fixture or wall washing fixture or smoke detector adapter, security camera adapter or simple blank cover. UGR<10 .Complies with EN60598-1 and pertinent regulations. Lifetime> 50,000h - L90 - B10 (Ta 25°C). Make: ERCO/ iGuzzini Blade R/ Fagerhult (AOR No.RA-19)

NS SITC of Surface mounting downlight with LED (Light Emitting Diode), system power of 15 W, luminous flux of luminaire 1650 lm, colour temperature of 4000K, Neutral white, CRI> 80, 70% of luminous flux after 50,000 operating hours, 230V constant current driver, direct light emission, housing in die-cast aluminium, polyester powder coated white applied over a 5 stage pre-treatment, opal protruded diffuser for uniform illumination, integral electronic dali control gear, Protection class II , IP 20, ø = 170 mm, H = 43 mm Make: Wipro / Signify / Regent (AOR No.RA-31)

NS SITC of Recessed downlight with HPE (High-Performance Efficiency) with LED (Light Emitting Diode), system power: 15 W, Luminous flux of luminaire 1425 lm, Colour temperature of 4000 K, Neutral white, CRI > 80, 230V constant current driver, 70% of luminous flux after 50,000 operating hours; energy-efficient LEDs, direct light emission, housing in die-cast aluminium, Polyester powder white coloured coat applied over a 5-stage pre-treatment trim, prismatic diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, Electronic dali control gear, Protection class II, IP 40, Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm. Make: Wipro / Signify / Regent (AOR No.RA-32)

NS SITC of Miniaturised round swivel luminaire complete with LED profiler projector with 6.5W in warm white colour tone and wattage not exceeding 9W. Luminaire Version compatible with Ring Luminaire diam 170mm complete with device for coupling it to the luminaire and DALI control gear. Die-cast aluminium technical body for LED lamp - an external pin that is activated manually allows the inclination of the luminaire to be locked and guarantee stability and high precision aiming - high definition OptiBeam reflector. The aluminium optical assembly includes a sophisticated telecentric optics system consisting of four anti-reflection-treated glass lenses. Black anodised aluminium locknut for manual focusing. The innovative optical system, combined with the option of manual adjustment and four shaping flaps, allows precise, well-defined wall lighting with no halo effects or soft edges. The optical assembly is fixed to the technical body with a rapid and practical magnetic system. This solution allows it to be rotated by 360° which increases its versatility considerably. The spotlight is designed to obtain a square, rectangular or variously irregular beam by manoeuvring the flaps. The package includes two gobos for circular shapes and it equipped with a mechanical lock operated manually. Make: ERCO/ iGuzzini Blade R/ Fagerhult (AOR No.RA-20)

NS SITC of Round swivel luminaire with 10W, and luminaire wattage not exceeding 12.5W in 3000k/4000K Color temperature CRI 90 with 355° internal rotation and max 30 tipping movement, designed to use LED lamps with C.o.B. technology with safety glass included. Version compatible with Ring Luminaire diam 170mm complete with device for coupling it to the luminaire and DALI control gear. The main swivel body is made of die-cast aluminium with a radiant surface that guarantees optimum heat dissipation. Metallised, thermoplastic, high definition reflector - medium optic (26°). Structure with die-cast aluminium external surface frame. The internal ring is made of thermoplastic available in a range of painted and metallised finishes. Make: ERCO/ iGuzzini Blade R/ Fagerhult (AOR No.RA-21)

NS SAFETY EQUIPMENT (Electrical & UPS Room only - M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

NS SITC of approx 10~15 watt, ww, Decorative Suspended Light of estimated size with height 600mm (approx.), made out of local stone/concrete/terrazo/corian incorporated while moulding is customized shape as per approved design. Assembled with required light fixtures wiring and all the nesseccary hardwares, intergration, electrical &mechanical elements. Make: Customized with design & detailed shop drawing as approved by Consultant. (AOR No.RA-37)

NS Optical Fibre Light Installation Supply and installation of sensor based optical fibre light installation in an area of 20 sqm. With 10,000 points of optical fibre of mixed diameterof size - 1.5,2,3 mm (in variable height), 10,000 crystal glass fixtures for optical fibre tip ends. With base framing and finishing in metal , hdwr wood. 1500pc led Dmx compatible dynamic optical fibre engine ports integrated with Arduino uno, Led matrix software - 14pc motion camera sensors. Pc for integration- PC - i7(Intel),GTX 1070 Graphic Card(AMD/NVIDIA) - 8 GB, 16 GB RAM(Kingston/Corsair/Transcend), Keyboard Mouse - HP/Logitech, Cabinet (Coolermaster/Corsair/Thermaltake) Microsoft Windows 10 pro . HDMI Wires (Venta/Amazon basics). The mechanism needs to be designed such that lights are responsive to presence and movement of visitors. The lights should be responsive to the movement of the visitors. Specialized artist/sculpturist on board for the installations to take necessary prior approvals from museum design consultant before execution. (AOR No.RA-38)

NS SITC of Surface & recessed mounted Track 1 meter Make: Bajaj/Philips, Litolux or equivalent. (AOR No.RA-40)

NS SITC of Surface & recessed mounted Track 2 meter Make: Bajaj/Philips, Litolux or equivalent. (AOR No.RA-41)

NS SITC of I / L - Connector Make: Bajaj/Philips, Litolux or equivalent. (AOR No.RA-42)

NS SITC of approx. 9 watt/ mtr, IP65 LED Strip in AL profile, 3k, on ground surface Make: Bajaj/Philips, Litolux or equivalent. (AOR No.RA-43)

NS SITC of approx. 7.5w/mtr, IP20 LED Strip in AL profile, 3k, inside cove Make: Bajaj/Philips, Litolux or equivalent. (AOR No.RA-44)

NS SITC of surface mounted approx. 28w 4ft LED Battens, 6k for kitchen/ stores/ office/ups/elect. room. Make: Bajaj/Philips, Litolux or equivalent. (AOR No.RA-45)

NS SITC of approx. 26 watt led spot, tiltable, surface mounted, 230 volt, 24 degree Make: Bajaj/Philips, Litolux or equivalent. (AOR No.RA-46)

NS SITC of approx. 10 watt led light, recessed mounted, 230 volt, 3000k Make: Bajaj/Philips, Litolux or equivalent. (AOR No.RA-47)

NS SITC of approx. 10 watt led light, Surface mounted, 230 volt, 3000k Make: Bajaj/Philips, Litolux or equivalent. (AOR No.RA-48)

NS Visitor Self Registration System - RFID Card/Band Dispanser touch screen Kiosk for Visitor Registration. Qty: 5nos. Make-MUTEK/eq with samsung 13" Touchscreen +Intel NUC mini PC with 200000 cards/BAND Server System For Visitor mangement System (Overall Museum & Considering common networking for network setup) - Processor family Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4 SSD- 1TB, HDD: 2 TB , Nvidia Quadro 4GB, 3DP, Windows 10 Pro 64 Bit With24" Monitor,K/M. Qty: 2nos. Make- Dell/HP/Asus LED Wall - Supply of Video wall with 1.5mm pixel pitch Indoor Model IE015A with minimum resolution(5760 X 1800), pixel density 640000 pixels/m²,Video wall size : 8.64 X 2.7 m , refresh rate >3840Hz,IP20, brightness should be 500 nits or better, contrast ratio 5000:1 or better, Viewing angle 150X150, HDR10, 100% front service, Remote power redundancy, should be complete with OEM ADA complied mounting with certification CE (includes EMC), FCC, IC; CB, UL,TUV, RCM.MAF also required from OEM .The Rates inclusive of all software, hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per design. Qty: 1nos. Make- Christie,Barco,Mitsubishi,Samsung,Delta Media Server for LED wall - Processor family Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4 SSD- 1TB, HDD: 2 TB , Nvidia Quadro 8GB, 3DP, Windows 10 Pro 64 Bit With24" Monitor,K/M. Qty: 1nos. Make-Dell/HP/ASUS Info Touchscreen Vertical kisok - CapacitiveTouchScreen, Diagonal Size 55",Type Edge LED BLU,Resolution 3840*2160 (4K UHD) Pixel Pitch(mm) 0.315 x 0.315,Active Display Area(mm) 1209.6(H) x 680.4(V),Brightness(Typ.):400 (with Touch glass), 500(without Touch Glass) nit Contrast Ratio 4,000:1 (without glass),Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7M,Color Gamut 92% (DCI-P3, CIE 1976 Operation Hour, 24/7 Haze,25% (Without Glass),Special Features H/W: Temperature Sensor,Pivot Display, Clock Battery(168hrs Clock Keeping), Built in Speaker(10W 2ch), Video Wall Daisy Chain(HDCP2.2:4EA,HDCP1.4:7EA), IP5x Rating, Wi-Fi/BT S/W: Auto Source Switching & Recovery, LFD Home UI, Button Lock, Hot key option, Plug&Play (Initial Setting) with 5 year onsite warranty. The Rates inclusive of all hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per design. Qty: 5nos. Make-Samsung/LG/Panasonic/Delta Mini PC for Info Kisok - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty: 3nos. Make-Intel/Dell/HP/ASUS Information Digital Signage Stretched displays - Diagonal Size 37",Type 60Hz E-LED BLU,Resolution 1920*540,Pixel Pitch(mm)0.4686(H) x 0.4686(V),Active Display Area(mm) 899.712(H) x 253.044(V) Brightness(Typ.) 700 nit., Contrast Ratio 4000:1 ,Viewing Angle(H/V) 178:178 ,Response Time(G-to-G) 16ms,Display Colors 8bit - 16.7M,Color Gamut 72%,Operation Hour 24/7,Haze 44%,Input-RGB DVI-I, Display Port 1.2,Video HDMI,HDCP,HDCP 2.2 Audio Stereo mini Jack USB, USB 2.0 x 1,Special Features H/W : USB Plug and Play, Tilting and Portrait Install support, Daisy Chains, Shock and Vibration certificated(IEC 61373) S/W : Magic Clone(to USB), RS232 MDC, , Video Wall, Smart Scheduling, Auto Source Switching, Internal Media Player.The Rates inclusive of all , hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per design. Qty: 5nos. Make-Samsung/LG/Panasonic/ Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional. Make-KRAMER/ATLONA/Dlink/Netrack/Comrack RFID Podiums Application - Application to retrive data from server while tab RFID card/Band on Podium Make-As per approved by museum Consultants General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Info Touchscreen Kisok - Display : 13” FHD display with 10-point multi-touch functionality,Diagonal Size 13",Type Edge LED,Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty. Qty: 20 Nos. Make-Samsung/LG/Panasonic/Delta/eq Mini PC for Info Kisok - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty: 20nos. Make-Intel/Dell/HP/ASUS Headphone - AutoPlay Available,Silver Conduit,8.4mm Cable Thickness,Available with Teardrop or Knuckle Mounting Plate,Fitted with a 90° Swivel Knuckle,With 3.5mm Headphone Jack,Ear Par Materia: Synthetic leather, circumaural ear pads. Qty: 15 Nos. Make-BlackboxAV, Bose or eq Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Gobo Projector for Floor - Ceiling Light Projection System RGB liquid crystal shutter projection system Projection Method Direct Mounting, Lighting Track (requires Lighting Track option), Floor Standing (requires Floor Stand option) Driving Method Poly-silicon TFT Active Matrix Pixel Number 1,024,000 dots (1280 x 800) x 3 Color Brightness3 Color Light Output: 2,200 lumens White Brightness3 White Light Output: 2,200 lumens Aspect Ratio 16:10 widescreen Native Resolution WXGA (1280 x 800) Light Source Laser Diode Laser Life1 Normal Mode: Up to 20,000 hours Extended Mode: Up to 30,000 hours Throw Ratio Range 1.38 (Zoom: Wide), 2.19 (Zoom: Tele) Size (Projected Distance) 30" – 150" [0.88 – 4.51 m] (Zoom: Wide) Keystone Correction Manual Vertical: ± 45 degrees; Horizontal: ± 40 degrees Dynamic Contrast Ratio Up to 2,500,000:1 Color Reproduction Up to 16.7 million colors Project from Nearly Any Angle Movement: Left/Right: 180 degrees, Up/Down: 180 degrees; Ball-joint Axis Rotation: 360 degrees Track Compatibility Halo: TEK441, 442, 443 Juno: TEK44FT(Black/White) Global Trac: TEK44-1, 44-2, 44-3, Lens Type Optical zoom (Powered)/Focus (Powered) F-number 1.51 – 1.92 Focal Length 18.2 – 28.4 mm Zoom Ratio 1 – 2.21 (Total), (Optical zoom: 1 – 1.58, Digital zoom: 1 – 1.4) with Media Player .The Rates inclusive of all software, hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per concept. The sound output to match premium cinema theatre level experience. Qty: 1 Nos. Make-EPSON/Christie/Barco Touchscreen Application - Application to play the content as per input from RFID. Qty: 7 Nos. Make-Custom Interactive Application - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder. Qty: 1 nos. Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 10 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 5 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 10 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Interactive Kit - Sensor Based Installation, Content triggered when visitor come in sensor area.Hokuyo UST-10LX. Qty: 4 nos. Make-Hokuyo UST-10LX Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Interactive Application - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder. Qty: 1 nos. Make-Custom Info Touchscreen Kisok - Display : 13” FHD display with 10-point multi-touch functionality,Diagonal Size 13",Type Edge LED, Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty. Qty: 4 nos. Make-Samsung/LG/Panasonic/eq Mini PC for Info Kisok - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty: 4 nos. Make-Intel/Dell/HP/ASUS Headphone - AutoPlay Available,Silver Conduit,8.4mm Cable Thickness,Available with Teardrop or Knuckle Mounting Plate,Fitted with a 90° Swivel Knuckle,With 3.5mm Headphone Jack,Ear Par Materia: Synthetic leather, circumaural ear pads. Qty: 4 Nos. Make-BlackboxAV, Bose or eq Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional. Qty: 1 nos. Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS SITC of High Luminance LED Spot Light with 220V and approx 26W, RGB/RGBW/DMX512 in, 1800~6500K CRI90 having net lumen out of 1658lm. Fixture should have an option of Super Spot, Medium, Flood and Wide Flood optics. (as per approval) . Indoor adjustable spotlight in Circular or Square design with adapter for installation. Device made of die-cast aluminium and a front part made of a thermoplastic material. Spotlight double adjustability allows a 360° rotation about the vertical axis and 15° to 90° tilting relative to the horizontal plane with a well-defined spot light beam. Life of LED should be > 50,000h (Ta upto 50°C). Overvoltage protection: 2kV Common mode & 1kV Differential mode. Fixture should have an option of White, Black finish as per site requirement. Fixture should not be more than ?121mm and 80 mm height. Make: Bajaj/Philips, Anoralux or equivalent. (AOR No.RA-49)

NS SITC of track mounted adjustable LED WALL WASHER with 220V and approx 36W in 1800-6500K .Outdoor/Indoor adjustable spotlight in Rectangular/Square design with adapter for installation and to have accessoriy for stand alone installation as surface mounted or ceiling recessed. Product complete with super pure anodized aluminium reflector to guarantee wall washer light distribution for vertical downlight wall illumination. Die-cast aluminium optical assembly. Rotates 360° about the vertical axis and tilts 45° relative to the horizontal plane. Passive heat dissipation. Option of installing an accessory asymmetric screen. Life of LED should be > 50,000h - L80 - B10 (Ta 50°C). Overvoltage protection: 2kV Common mode & 1kV. Differential modeFixture should have an option of White, Black finish as per site requirement. Fixture should not be more than 1000mm length 55mmwidth and 119mm in height. IP67 Make: Bajaj/Philips, Anoralux or equivalent. (AOR No.RA-50)

NS SITC of Inground tree Uplight IP67 IK10 Recessed luminaire applicable to the floor or ground, designed for fitting monochrome white LED with 8W in 1800-6500K CRI80. Total System Wattage of the fixture should not exceed 12W. The round frame has a diameter D=158 mm; the body and frame are made of die cast aluminium with sodium-calcium extra clear glass, thickness 15 mm. The luminaire is fixed to the outer casing by means of two TORX-type screws that ensure proper anchoring. Overvoltage protection: 4KV Common mode, 3,5KV differential mode. Life Time: >50000 h - L80 - B10 (Ta 50°C). The outer casing for installation can bordered separately from the plastic optical assembly. The assembly made up of the frame, optical assembly and outer casing guarantees 5000 kg resistance to static loads. Maximum glass surface temperature is lower than 40°C. Make: Bajaj/Philips, Anoralux or equivalent. (AOR No.RA-51)

NS SITC of profile projector equipment with 30W high power LED. The luminous flux of the projector light should be 18000-20000LM. The equipment to be fit for indoor/outdoor application with necessary hardwares, fixtures etc all complete. The colour temperature to vary from 1500-6500K with light source life of atleast 30000 hours. voltage to be considered 30-36v. The cost to be inclusive of all cables, drivers, controllers etc required for proper functioning of the luminaire Make: Bajaj/ Anoralux or equivalent. (AOR No.RA-52)

NS Supply Installation, Testing and Commissioning of following Control Touch Panels for approx all the galleries and back end control Equipments, including DALI modules, Cat 6A wires, conduits, all network hardwares & softwares and ancillaries including all necessary accessories, supports, etc., complete as required to complete the lighting management system. with 6" Inch Ethernet Based Touch Screen in Each gallaries ; DALI Control Module with 128 channels and 128 groups; Ethernet and iCAN based Network Device ; Lighting control Panel and Accessories ; (LMS shall be planned for Each galleries independently with approval from client/ designer) Make: iLight/ Pharos/ Dynalite/eqv (AOR No.RA-53)

NS 75" Display - Supplying and installation LED TV with minimum bezel - 75" , Magic Info Supprted, Inbuilt Tizon OS, 5 Year Onsite Warranty, 4K Resolution. Inclusive of all - ardware, Push Pull Mount , electrical, mechanical or any other mechanism required to make it functional. Make- Make - Samsung/ Christie / Delta Equivalent

NS Android Tablets - WiFi Android Tablet (Android 12, Qualcomm Snapdragon, 27.94cm (11 Inches), 8GB RAM, 128GB ROM, with 5 year warranty. Qty: 20 Nos. Make-Samsung/Lenovo Or Eq AR Core Application on Camera View of Physical installed 3D objects on printed india map on floor - Custom AR Application Offline Mode : The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 30nos. Make- Christie,Barco, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 9nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 30nos. Make- Dataton/Coolux/Pixera/Vioso Equivalent Dual Sided Projection Film - 360 DUAL IMAGE PROJECTION FILM,Dual image (mirror image on one side),Off-white film with self-adhesive layer,120 Micron thickness,Two images using only one projector,Supports wide viewing angles,Supports 4K or HD rear projection,This Film will be pasted on the glass wall and projection from on side will be displ;ay mirror on toher side of glass. Qty: 1nos. Make-ProDisplay,Glimm or eq Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional. Qty: 1nos.Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Printing of 10 leaf museum brochure of size 200mm X 700mm of 1000 copies as approved by musuem consultant.the quality material, color etc of the final product should be exactly same as per the sample approved after the desigining phase.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 4nos. Make- Christie,Barco, Digital Projection Content Server - Display media server with HD outputs as required , synced together. It should be capable of capturing content. Original windows 10 Pro with i7 six core CPU with Rugged cooling system. with 16GB RAM, 2 nos 512 SSD drives raid 0 drives for media playback , 1 nos. 256 GB SSD for operating. It should also have Rack Mountable,genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 1 nos. Make- HP/Dell/Asus Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 4 nos. Make- Dataton/Coolux/Pixera or Equivalent Mechnical Mashal (FIX) - 5 set Mechnical Mashal Movement that control the Projection in seprate section, Like Joy-stick in game , Mashal will control the Path movement in projection. Mechnical mashal Unit with Controller. Qty: 5 nos. Make-Custom Application - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder. Qty: 1 nos. Make-As per approved by museum Consultants Acessories - Transmitters- Recievers over CAT6 upto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-ATEN/KRAMER/DLINK Or Eq RFID Controlled Battery Operated Mashal - 150 Units Battery Operated Light Based Mashal, Mashal Light contrilled by RFID scanner radius. Some Mashal fliker when go out the scanning range.Customised Controller inside the Mashal. Design & Functionality of Mashal should be approved by Design Consultant.Qty: 1 50 nos. Make-Customised General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 41 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects.Qty: 15 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 41 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector For Atrocities documentary - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 2 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 1 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 2nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 20 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 7 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 20 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional. Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Interactive Kit - Sensor Based Installation, Content triggered when visitor come in sensor area.Hokuyo UST-10LX. Qty: 4 nos. Make-Hokuyo UST-10LX General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Information Kiosk For Details - Display : 13” FHD display with 10-point multi-touch functionality,Diagonal Size 13",Type Edge LED,Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty .Qty: 5 nos. Make-Samsung/LG/Panasonic/Delta Mini PC - Intel® NUC Mini PC with 12th Generation Intel® Core™ Processors,Intel® Core™ i7 Processor),Windows 11 Pro*,2x 8GB DDR4-3200 SODIMMs,500GB Gen 4 NVMe SSD,Dual HDMI 2.0b w/HDMI CEC,Front: 2x USB 3.2 Rear: 1x USB 3.2, 1x USB 2.0 Internal: 1x USB 3.2 on m.2 22x42 (pins), 2x USB 2.0 (headers),Front panel: 3.5mm headphone/mic jack, with 3 year warranty. Qty: 5 nos. Make-Intel/Zotac Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional. Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Application - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder. Qty: 1 nos. Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Touch Display - Supply of 32" Touchscreen,Capactive touch inbuilt,Diagonal Size : 32",Type Edge LED BLU,Resolution 3840*2160,Pixel Pitch(mm) : 0.3638 x0.3638,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7M,Color Gamut 72%,Haze : 2% (Without Glass),Built in Speaker(10W + 10W),Input :Display Port 1.2 (1),HDMI 2.0 (2),HDCP2.2,USB 2.0 x 2,Output : HDMI 2.0 (Loop-out),Stereo mini Jack,USB Type-B x 2 (Touch Sensor Data, PC 1 / SoC 1),External Control ,RS232C(in/out) thru stereo jack, RJ45,Special Features H/W: Temperature Sensor,Pivot Display, Clock Battery(168hrs Clock Keeping), Built in Speaker(10W 2ch), Video Wall Daisy Chain(HDCP2.2:4EA,HDCP1.4:7EA), IP5x Rating, Wi-Fi/BT S/W : Auto Source Switching & Recovery, LFD Home UI, Button Lock, Hot key option, Plug&Play (Initial Setting), With 5 Year warranty. Qty: 5 nos. Make-Samsung/LG/Panasonic/Delta Media Player - Intel® NUC Mini PC with 12th Generation Intel® Core™ Processors,Intel® Core™ i7 Processor),Windows 11 Pro*,2x 8GB DDR4-3200 SODIMMs,500GB Gen 4 NVMe SSD,Dual HDMI 2.0b w/HDMI CEC,Front: 2x USB 3.2 Rear: 1x USB 3.2, 1x USB 2.0 Internal: 1x USB 3.2 on m.2 22x42 (pins), 2x USB 2.0 (headers),Front panel: 3.5mm headphone/mic jack, with 3 year warranty. Qty: 5 nos. Make-Intel/Dell/HP Acessories - , LAN Cables, Switcher,Push Pull Mount and all other accessoeries required to Exhibit Functional Make-Logitech,TFMINI,LUNA or Eq Magic Mirror Application - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder. Qty: 1 nos. Make-Custom Logitech 4K Webcam Camer with photoprinter - Logitech 4K Webcam and canon/Sony,EPSON,6*4" photo printer with 2 Lakh counsumables. Fast printing. Qty: 5 nos. Make-BlackboxAV, Bose or eq Display - Supply of video wall with 55" extreme narrow bezel HD resolution panels,IP Rating IP5X(Certificate required with the Bid Submission),Haze 28%,, brightness should be 700 nits or better, contrast ratio 1200:1 or better, combined bezel size should not exceed 1.8 mm, Depth of the panel should be below 71mm,Video Wall Daisy Chain(10x10),, viewing angle must be 178 degrees or better. It should be complete with mounting (4*4 Matrix). Product must be UL,FCC,BIS,CE certified. Certificate copy required with the Bid Submission.OEM Authorisation MAF required at the time of submission. Make-Samsung/Christie/Panasonic/Delta General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 2 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 1 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 2 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Application - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder. Qty: 1nos. Make-Custom Interactivity - User Interact with the PALM on the interactive custom made PODs which triggered the Optical fiber lights and goes up to tree and projection content will change in particulat area. 50 Pods for Interaction as per the design Consultant . Visiter Put the Palm on POD that trigger the DOT Less LED strip light starts from POD go to the tree via floor Map and connect to the Complet Tree. Qty: 1 nos. Make-Custom Retractable screen - 8*4 Meter atomatic slider Projection wall screen, Controlled via system, Silent motors and mechanism. Linear guide system with all accessories to make it functional.Motorised silent sliding screen, Automated and synced with the projection show . Qty: 1 nos. Make-Cistom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency

NS Touchscreen Kisok - Supply of 32" Touchscreen,Capactive touch inbuilt,Diagonal Size : 32",Type Edge LED BLU,Resolution 3840*2160,Pixel Pitch(mm) : 0.3638 x0.3638,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7M,Color Gamut 72%,Haze : 2% (Without Glass),Built in Speaker(10W + 10W),Input :Display Port 1.2 (1),HDMI 2.0 (2),HDCP2.2,USB 2.0 x 2,Output : HDMI 2.0 (Loop-out),Stereo mini Jack,USB Type-B x 2 (Touch Sensor Data, PC 1 / SoC 1),External Control ,RS232C(in/out) thru stereo jack, RJ45,Special Features H/W: Temperature Sensor,Pivot Display, Clock Battery(168hrs Clock Keeping), Built in Speaker(10W 2ch), Video Wall Daisy Chain(HDCP2.2:4EA,HDCP1.4:7EA), IP5x Rating, Wi-Fi/BT S/W : Auto Source Switching & Recovery, LFD Home UI, Button Lock, Hot key option, Plug&Play (Initial Setting), With 5 Year warranty. Qty: 32 Nos. Make-Samsung/LG/Panasonic/eq Mini PC for Info Kisok - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty: 32 Nos. Make-Intel/Dell/HP/ASUS RDIF Reader - RFID Reader, 13.56MHz USB Proximity Sensor Smart RFID IC Card Reader. Qty: 32 Nos. Make-Standard Headphone - AutoPlay Available,Silver Conduit,8.4mm Cable Thickness,Available with Teardrop or Knuckle Mounting Plate,Fitted with a 90° Swivel Knuckle,With 3.5mm Headphone Jack,Ear Par Materia: Synthetic leather, circumaural ear pads. Qty: 12 Nos. Make-BlackboxAV, Bose or eq Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Touchscreen Application - Application to play the content as per input from RFID . Qty: 1 Nos. Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 11 Nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 5 Nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 11 Nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Walking VR Simulator (VR Trademill) with screen - Virtual Walking simulator with VR device which output extended to 65" screen. HMD Specification :Display resolution: 1200 x 1080 (per eye),Display refresh rate: 90Hz or higher,Orientation sensors: Gyroscope,Audio: Hi-Res certificate headset , Hi-Res certificate headphone (removable) , High impedance headphone support accelerometer, magnetometer,4m custom smart cable,Replaceable facial interface.Simulator Specification : 6 DoF Electric actuators motion Platform The system must work with electric actuator stroke-100. Smooth Functioning Like trademil and same is sync with the content.Dimension of complete simulator is 1.5m * 1.5m maimum. Support custom application. Onsite 3 year warranty. Complet simulator working should be silent. Workstation i7/16GB/1TB/ Quadro GFX,Windows 10 pro, Rackmountable With 5 Year Onsite Warranty Extended Display : Supplying and installation LED TV with minimum bezel - 65" .Dynamic Crystal Color with Quantum Processor 4K for incredible picture quality,Resolution 3840x2160(16:9),Pixel Pitch(mm) :0.372 x 0.372,Brightness : 700 nits,Contrast Ratio : 4000:1,Color Gamut : 92% (DCI-P3, CIE 1976),Haze Non-Glare,Processor Cortex A72 1.7GHz Quad-Core CPU. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Qty: 4 Nos. Make-Make : FUNVR or Custom as per required intend VR Walking Game Application - The VR application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder Make-As per approved by museum Consultants VR Egg Arcade Simulator - VR Egg Shape Simulator with 3 DOF Electric Platform with 3 electric cylinder,Motion Angle :From to back : 25-30 degree, Left to Right : 25-30 Degree,voltage / power : 220V / 1.5 KW, Complete setup is silent working, Panic/Emergancy button should be active all the time,Onsite warranty : 5 year,Dimension of complete simulator is 1.5m * 1.5m maimum. Support custom application. Onsite 3 year warranty. Complet simulator working should be silent. Workstation i7/16GB/1TB/ Quadro GFX,Windows 10 pro, Rackmountable With 5 Year Onsite Warranty Extended Display : Supplying and installation LED TV with minimum bezel - 65" .Dynamic Crystal Color with Quantum Processor 4K for incredible picture quality,Resolution 3840x2160(16:9),Pixel Pitch(mm) :0.372 x 0.372,Brightness : 700 nits,Contrast Ratio : 4000:1,Color Gamut : 92% (DCI-P3, CIE 1976),Haze Non-Glare,Processor Cortex A72 1.7GHz Quad-Core CPU. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Qty: 4 Nos. Make-9D or Custom or Eq. VR Egg Simulator Application - The VR application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder Make-As per approved by museum Consultants Acessories - Cables& Connectors, Push-Pull Mounts, Power sockets, and everything to make exhbit function as per design consultants Make-ATEN/KRAMER/DLINK Or Eq General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 20 Nos. Make-Christie/Barco/NEC Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 7 Nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 20 Nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Touchscreen - Display : 13” FHD display with 10-point multi-touch functionality,Diagonal Size 13",Type Edge LED,Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty . Qty: 20 Nos. Make-Samsung/LG/Panasonic/Delta Mini PC for Info Kisok - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty: 20 Nos. Make-Intel/Dell/HP/ASUS Headphone - AutoPlay Available,Silver Conduit,8.4mm Cable Thickness,Available with Teardrop or Knuckle Mounting Plate,Fitted with a 90° Swivel Knuckle,With 3.5mm Headphone Jack,Ear Par Materia: Synthetic leather, circumaural ear pads. Qty: 8 Nos. Make-BlackboxAV, Bose or eq Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Gobo Projector for Floor - Ceiling Light Projection System RGB liquid crystal shutter projection system Projection Method Direct Mounting, Lighting Track (requires Lighting Track option), Floor Standing (requires Floor Stand option) Driving Method Poly-silicon TFT Active Matrix Pixel Number 1,024,000 dots (1280 x 800) x 3 Color Brightness3 Color Light Output: 2,200 lumens White Brightness3 White Light Output: 2,200 lumens Aspect Ratio 16:10 widescreen Native Resolution WXGA (1280 x 800) Light Source Laser Diode Laser Life1 Normal Mode: Up to 20,000 hours Extended Mode: Up to 30,000 hours Throw Ratio Range 1.38 (Zoom: Wide), 2.19 (Zoom: Tele) Size (Projected Distance) 30" – 150" [0.88 – 4.51 m] (Zoom: Wide) Keystone Correction Manual Vertical: ± 45 degrees; Horizontal: ± 40 degrees Dynamic Contrast Ratio Up to 2,500,000:1 Color Reproduction Up to 16.7 million colors Project from Nearly Any Angle Movement: Left/Right: 180 degrees, Up/Down: 180 degrees; Ball-joint Axis Rotation: 360 degrees Track Compatibility Halo: TEK441, 442, 443 Juno: TEK44FT(Black/White) Global Trac: TEK44-1, 44-2, 44-3, Lens Type Optical zoom (Powered)/Focus (Powered) F-number 1.51 – 1.92 Focal Length 18.2 – 28.4 mm Zoom Ratio 1 – 2.21 (Total), (Optical zoom: 1 – 1.58, Digital zoom: 1 – 1.4) with Media Player .The Rates inclusive of all software, hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per concept. The sound output to match premium cinema theatre level experience. Qty: 5 Nos. Make-EPSON/Christie/Barco Touchscreen Application - Application to play the content as per input from RFID . Qty: 1 Nos. Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 2 Nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Workstation i7/16GB/1TB/ Quadro GFX,Windows 10 pro, Rackmountable With 5 Year Onsite Warranty, Balckmagic Capture Card for DSLR Camera Input. Qty: 1 Nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 2 Nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Dual Sided Projection Film - 360 DUAL IMAGE PROJECTION FILM,Dual image (mirror image on one side),Off-white film with self-adhesive layer,120 Micron thickness,Two images using only one projector,Supports wide viewing angles,Supports 4K or HD rear projection,This Film will be pasted on the glass wall and projection from on side will be display mirror on toher side of glass.Camera will be fix in center of the glass to capture vistior who seeing in well from upside. Face diffucsed light also required in inner part of Well to focus on visitor face. Qty: 1 Nos. Make-ProDisplay,Glimm or eq DSLR Camera - Wide Angle DLSR Camera, Capture 5 meter radius from 3 meter distance, AC to dc Power Adopter for Continue power supply, Lens as per requirement. Support cables for Capture card to provide inoput to Server PC,3 Year Warranty. Qty: 1 Nos. Make-Canon/Nikon/Sony Acessories - Transmitters- Recievers over CAT6 upto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional. Qty: 1 Nos. Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Face Filter Application - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder. Qty: 1 Nos. Make-As per approved by museum Consultants General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Display - Supplying and installation LED TV with minimum bezel - 65" .Dynamic Crystal Color with Quantum Processor 4K for incredible picture quality,Resolution 3840x2160(16:9),Pixel Pitch(mm) :0.372 x 0.372,Brightness : 700 nits,Contrast Ratio : 4000:1,Color Gamut : 92% (DCI-P3, CIE 1976),Haze Non-Glare, Processor Cortex A72 1.7GHz Quad-Core CPU. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Qty: 4 nos. Make-Christie,Samsung/LG/Panasonic/Delta Peephole Lens - Solid Brass Security Peephole for 1.65" to 2.16". Qty: 4 nos. Make-Custom Acessories - All acessories to make exhbit functional Make-Job Touchscreen - Display : 13” FHD display with 10-point multi-touch functionality,Diagonal Size 13",Type Edge LED,Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty. Qty: 4 nos. Make-Samsung/LG/Panasonic/Delta Mini PC for Info Kisok - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty: 4 nos. Make-Intel/Dell/HP/ASUS Interactive Kit to Dispense Smoke from Canon - Smoke from Canon will trigger when visiter interect with the touchscreen, Included the Smoke Machine and filling material for 5 years.Customised Controller also required to control Smoke machine dispense via canel. Qty: 1 nos. Make-Customised Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Display - Supplying and installation LED TV with minimum bezel - 65" .Dynamic Crystal Color with Quantum Processor 4K for incredible picture quality,Resolution 3840x2160(16:9),Pixel Pitch(mm) :0.372 x 0.372,Brightness : 700 nits,Contrast Ratio : 4000:1,Color Gamut : 92% (DCI-P3, CIE 1976),Haze Non-Glare,Processor Cortex A72 1.7GHz Quad-Core CPU. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Qty: 4 nos. Make-Christie,Samsung/LG/Panasonic/Delta Sensor to Connect brick trigger Content - TF Mini Lidar Sensor. Qty: 4 nos. Make-TF Mini Acessories - All acessories to make exhbit functional Make-Job General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Hologram with 55" Screen Controller - Hologram display 270 degree using 55" display(3 sided), ,Pyramid : Tempered Optical Glass,Display Resolution : 1920x1080,Input : USB,VGA,HDMI,USB,VGA,HDMI, With Three yrear warranty. Qty: 3 nos. Make-Custom Mini PC - Intel® NUC Mini PC with 12th Generation Intel® Core™ Processors,Intel® Core™ i7 Processor),Windows 11 Pro*,2x 8GB DDR4-3200 SODIMMs,500GB Gen 4 NVMe SSD,Dual HDMI 2.0b w/HDMI CEC,Front: 2x USB 3.2 Rear: 1x USB 3.2, 1x USB 2.0 Internal: 1x USB 3.2 on m.2 22x42 (pins), 2x USB 2.0 (headers),Front panel: 3.5mm headphone/mic jack, with 3 year warranty. Qty: 3 nos. Make-Intel/Zotac General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS 3D Model detachable - 100 Models of soldiers and soldiers seating on horses as per the design consultant. Make-Custom Automated Movement in linear direction Mechanism - Complete Automated Show of war in two armys. 2 Seprate 3D modeled soldiers are move in linerar direction which are predifined on the table and 1 army soldiers fell down. After completion the one show, Soldiers reset in their initial position. Complete linear guide with stepper motor and customised controller. Noise free Solution. Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Touchscreen - Display : 13” FHD display with 10-point multi-touch functionality,Diagonal Size 13",Type Edge LED,Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty. Qty: 4nos. Make-Samsung/LG/Panasonic/Delta Rasbery Pi 4GB 32GB with Switch Trigger - Rasberry PI . Qty: 4nos. Make-Rasbery PI Controller with Programming - Display trigger the AV when someone open the door and interect with the touchscreen . Qty: 1nos. Make-Customised Headphone - AutoPlay Available,Silver Conduit,8.4mm Cable Thickness,Available with Teardrop or Knuckle Mounting Plate,Fitted with a 90° Swivel Knuckle,With 3.5mm Headphone Jack,Ear Par Materia: Synthetic leather, circumaural ear pads. Qty: 8nos. Make-BlackboxAV, Bose or eq General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 2 nos. Make-Christie/Barco/NEC Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 1 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 2 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional. Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Automated Motorised Kathputli Show with the help of real Kathputlis. - Providing complete technical solution for haryana documentary gallery. This gallery has mechanical and automated katputli movement show of duration of 8-10 minutes of occurrences of battles in different regions of Haryana and the tough fight between the different people of Haryana and the British army. The entire show will highlight the major events of the Freedom Struggle in the region. Using the media of the Automated Katputli folk culture i.e. the puppetry show which is different puppets handled by few strings for movement. The puppets to be of varyinng size from 400 -1500mm, made of wood carving, fabric, metal wire, frp, attached with strings and other suitable mechanism/motors synced with the controller as per the design to show different movements along with other props and scenography elements as per approved by musuem design consultants. Proper operation and mechanism to be considered while designing the mechanical show. Provision for integration of the mechanical movements along with projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. The customized programming of the puppet show needs to be synced for moveable/rotateable parts along with the audio visuals. The cost of puppets, along with the attire, props/elements/artefacts as required as per the design and theme to be consdered. There will be a motorised curtain operated with the remote for beginning and climax of the show to be controlled at the server station. Inclusive of all the mechnical, automation, synchronisation, development of softwares required to meet the intent of the gallery as specified in the scenography. Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty: 15 nos. Make-Christie/Barco/NEC Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty: 5 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty: 15 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Android Tablets - WiFi Android Tablet (Android 12, Qualcomm Snapdragon, 27.94cm (11 Inches), 8GB RAM, 128GB ROM, with 5 year warranty. Qty: 10 Make-Samsung/Lenovo Or Eq AR Core Application - Custom AR Application Offline Mode : The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Automated Object lifting ( up/down) Mechanism - Automated Object lifting ( Up/Down) Mechanism , Total Object s- 10, Silent Automated Object lifting ( Up/down) Mechanism using transparent wire and all accessories to make it functional. Make-Custom Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Make-Dell/HP/ASUS Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty. : 8 Nos. Make-Christie/Barco/NEC Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty. : 3 Nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty. : 8 Nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty.: 6nos. Make-Christie/Barco/NEC Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty.: 3nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty.: 6nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Coomunication Equipment - Telegram (Morse Keyer Telegraph) unit will be installed on 8 tables and show live communication and transition will be showed by LED effect and message display on projection. Qty.: 8nos. Make-Custom Special Effect - Optical Fiber light installation in ceiling to show the transmission of messages Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Display - Supplying and installation LED TV with minimum bezel - 65" .Dynamic Crystal Color with Quantum Processor 4K for incredible picture quality,Resolution 3840x2160(16:9),Pixel Pitch(mm) :0.372 x 0.372,Brightness : 700 nits,Contrast Ratio : 4000:1,Color Gamut : 92% (DCI-P3, CIE 1976),Haze Non-Glare,Processor Cortex A72 1.7GHz Quad-Core CPU. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Qty.: 4 nos. Make-Christie,Samsung/LG/Panasonic/Delta Mini PC for Info Kisok - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable . Qty.: 4 Nos. Make-Intel/Dell/HP/ASUS Application (Morse Code to msg converter in real time to show the visitor)Communication b/w to telegram Keyer - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder Make-Custom Coomunication Equipment With Digital Controller - Telegram (Morse Keyer Telegraph) unit will be installed on 8 tables and show live communication and transition will be showed by LED effect and message display on projection. Qty.: 4nos. Make-Custom Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty. 10 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty. 4 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty. 10 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Special Effedts - Make-Customised - Smoke Effect, Ligting Effect,Tornado Effect,Water Spray Make- Automation of the show - Complet show sync with the projection,Music and Special Effects Make-Customised General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty.: 6 nos. Make- Christie,Barco,NEC, Digital Projection Media Payer - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty.: 6nos. Make-Intel/Dell/HP/ASUS Directional Sound Dome/Shower - SITC of Single Localizer Sound Dome, Provides 80% drop-off from sweet spot under dome to sound heard just outside dome's edge. ,Isolation 14 dB ,Stereo Separation 10 dB,Listening Region 30"H x 12"W x 12"D (0.8m x 0.3m x 0.3m) ,Amplifier Minimum: 1 watts continuous per channel Maximum: 50 watts peak per channel ,Input Impedance 6 Ohms,Sensitivity 102dB SPL 1 watt, 1 meter@ 1kHz. Qty.: 6 nos. Make-Bose, BROWN INNOVATIONS or Eq Gobo Projector for Floor - Ceiling Light Projection System RGB liquid crystal shutter projection system Projection Method Direct Mounting, Lighting Track (requires Lighting Track option), Floor Standing (requires Floor Stand option) Driving Method Poly-silicon TFT Active Matrix Pixel Number 1,024,000 dots (1280 x 800) x 3 Color Brightness3 Color Light Output: 2,200 lumens White Brightness3 White Light Output: 2,200 lumens Aspect Ratio 16:10 widescreen Native Resolution WXGA (1280 x 800) Light Source Laser Diode Laser Life1 Normal Mode: Up to 20,000 hours Extended Mode: Up to 30,000 hours Throw Ratio Range 1.38 (Zoom: Wide), 2.19 (Zoom: Tele) Size (Projected Distance) 30" – 150" [0.88 – 4.51 m] (Zoom: Wide) Keystone Correction Manual Vertical: ± 45 degrees; Horizontal: ± 40 degrees Dynamic Contrast Ratio Up to 2,500,000:1 Color Reproduction Up to 16.7 million colors Project from Nearly Any Angle Movement: Left/Right: 180 degrees, Up/Down: 180 degrees; Ball-joint Axis Rotation: 360 degrees Track Compatibility Halo: TEK441, 442, 443 Juno: TEK44FT(Black/White) Global Trac: TEK44-1, 44-2, 44-3, Lens Type Optical zoom (Powered)/Focus (Powered) F-number 1.51 – 1.92 Focal Length 18.2 – 28.4 mm Zoom Ratio 1 – 2.21 (Total), (Optical zoom: 1 – 1.58, Digital zoom: 1 – 1.4) with Media Player .The Rates inclusive of all software, hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per concept. The sound output to match premium cinema theatre level experience. Qty.: 6 nos. Make-EPSON/Christie/Barco General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS VR Headsets - Supply, installation, testing and commissioning ofOculus Quest 2, . The Rates inclusive of all software, hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per concept.Qty.: 1 nos. Make-Oculus Application - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder. Qty.: 1 nos. Make-As per approved by museum Consultants Acessories - Transmitters- Recievers over CAT6 upto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-Standard General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Touchscreen Kisok - Display : 13” FHD display with 10-point multi-touch functionality,Diagonal Size 13",Type Edge LED,Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty. Qty.: 3 nos. Make-Samsung/LG/Panasonic/eq Mini PC for Info Kisok - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty.: 3nos. Make-Intel/Dell/HP/ASUS Headphone - AutoPlay Available,Silver Conduit,8.4mm Cable Thickness,Available with Teardrop or Knuckle Mounting Plate,Fitted with a 90° Swivel Knuckle,With 3.5mm Headphone Jack,Ear Par Materia: Synthetic leather, circumaural ear pads. Qty.: 3nos. Make-BlackboxAV, Bose or eq Capacitive touch sensor - 12-15 Capacitive sensor that works from behind the corian,using aurdino and ESP. Make- Application - Touchscreen Application with Capacitive senor Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. Make- - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency. Make-

NS Hologram with 55" Screen Controller - Hologram display 270 degree using 55" display(3 sided), ,Pyramid : Tempered Optical Glass,Display Resolution : 1920x1080,Input : USB,VGA,HDMI,USB,VGA,HDMI, With Three yrear warranty. Qty.: 3 nos. Make-Custom Mini PC - Intel® NUC Mini PC with 12th Generation Intel® Core™ Processors,Intel® Core™ i7 Processor),Windows 11 Pro*,2x 8GB DDR4-3200 SODIMMs,500GB Gen 4 NVMe SSD,Dual HDMI 2.0b w/HDMI CEC,Front: 2x USB 3.2 Rear: 1x USB 3.2, 1x USB 2.0 Internal: 1x USB 3.2 on m.2 22x42 (pins), 2x USB 2.0 (headers),Front panel: 3.5mm headphone/mic jack, with 3 year warranty. Qty. : 3 nos. Make-Intel/Zotac 3D Animation AV for Hologram - 3D animation AV of 3-4m as per approved intent by design consultant Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Display - Supplying and installation LED TV with minimum bezel - 65" .Dynamic Crystal Color with Quantum Processor 4K for incredible picture quality,Resolution 3840x2160(16:9),Pixel Pitch(mm) :0.372 x 0.372,Brightness : 700 nits,Contrast Ratio : 4000:1,Color Gamut : 92% (DCI-P3, CIE 1976),Haze Non-Glare,Processor Cortex A72 1.7GHz Quad-Core CPU. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Qty.: 4 nos. Make-Christie,Samsung/LG/Panasonic/Delta Peephole Lens - Solid Brass Security Peephole for 1.65" to 2.16". Qty.: 4 nos. Make-Custom Acessories - All acessories to make exhbit functional Make-Job General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS VR Headsets - Supply, installation, testing and commissioning ofOculus Quest 2, . The Rates inclusive of all software, hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per concept. Qty.: 8 nos. Make-Oculus Application - The application software to be developed in enterprise version / commercial version of the gaming engines (Unity3D, Unreal etc.) which supports real time 3d rendering and texture/ light baking. All the API Communication with any kind of server if need to be done in PHP/ MySQL as backend if needed. The developed application should have perpetual license and no subscription at any given point of time. Application/Software development cost to be inclusive of SRS, UI/UX, 2D design, 3D design or anything else needed to run the application. Application flow and UI/UX to be finalised once approved by the museum consultant/ authorities. Bidder will be responsible for submission of application source code technical documents and user manuals. All submitted documents to be digitally signed by the authorised signatory from the bidder. Qty.: 1nos. Make-As per approved by museum Consultants Acessories - Transmitters- Recievers over CAT6 upto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-Standard General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector- 3 5000 lumens - Supply of DLP Solid state(Laser Phosphor) Projection system with ultra short throw lens 0.25/0.5:1 ratio, having 5000 Lumens, 3D available, 1920 x 1200 Native Resolution,1800:1 Contrast Ratio, Lamp Life 20000 hours, Inputs: HDMI/HDBaseT/VGA,Audio in; & projector mountin bracket etc. Make- Christie,Barco,NEC, Digital Projection

NS Info Touchscreen Kiosk - 13" - Display : 13” FHD display with 10-point multi-touch functionality,Diagonal Size 13",Type Edge LED,Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty. Make-Samsung/LG/Panasonic/Delta/eq

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty.: 1nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty.: 1 nos. Make-Dell/HP/ASUS Holographic Film - Custom sizes Holographic film for projection. The Rates inclusive of all software, hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per concept. The sound output to match premium cinema theatre level experience. Make-Standard Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty.: 1 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Android Tablets - WiFi Android Tablet (Android 12, Qualcomm Snapdragon, 27.94cm (11 Inches), 8GB RAM, 128GB ROM, with 5 year warranty. Make-Samsung/Lenovo Or Eq

NS Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Make-Dell/HP/ASUS

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty.: 5 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty.: 2 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty.: 5 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Interactive Floor Sensor - Interactive Floor Sensors hokoyo or eq. to achive complete floor interactive . Qty.: 1 nos. Make- General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS NonTouch Display - Display : 13” FHD display,Diagonal Size 13",Type Edge LED,Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty . Qty.: 6nos. Make-Samsung/LG/Panasonic/Delta Mini PC for Display - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty.:6nos. Make-Intel/Dell/HP/ASUS Headphone - AutoPlay Available,Silver Conduit,8.4mm Cable Thickness,Available with Teardrop or Knuckle Mounting Plate,Fitted with a 90° Swivel Knuckle,With 3.5mm Headphone Jack,Ear Par Materia: Synthetic leather, circumaural ear pads. Qty.: 6nos. Make-BlackboxAV, Bose or eq Application with UI/UX - Touchscreen Application Make-Custom Special Interactive Effect - Sound from wooden pillers Triggered via sensor when visiter goes nearby Make-Custom - smoke effect Make- RFID Bases Solution Using Petals - 100 RFID tags installed in 3D modeled/FRP Petals. Video Triggered in display when visitor touch/cross the petal in particular RFID reader area. Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Mini PC - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Make-Intel/Dell/HP/ASUS

NS Headphone - AutoPlay Available,Silver Conduit,8.4mm Cable Thickness,Available with Teardrop or Knuckle Mounting Plate,Fitted with a 90° Swivel Knuckle,With 3.5mm Headphone Jack,Ear Par Materia: Synthetic leather, circumaural ear pads. Make-BlackboxAV, Bose or eq

NS Kinectic mechanism - Linear Motion based unit using stepper motor With Encoder & Gearbox to move the wooden block updown 200mm fixed on table. Loop IN/OUT b/w the units and controlled via computer. Qty.: 350 nos. Make-Custom Controller - Controller for Kinetic Unit . Qty.: 117 nos. Make-Custom Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty.: 2 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty.: 2 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty.: 2 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Gobo Projector for Floor - Ceiling Light Projection System RGB liquid crystal shutter projection system Projection Method Direct Mounting, Lighting Track (requires Lighting Track option), Floor Standing (requires Floor Stand option) Driving Method Poly-silicon TFT Active Matrix Pixel Number 1,024,000 dots (1280 x 800) x 3 Color Brightness3 Color Light Output: 2,200 lumens White Brightness3 White Light Output: 2,200 lumens Aspect Ratio 16:10 widescreen Native Resolution WXGA (1280 x 800) Light Source Laser Diode Laser Life1 Normal Mode: Up to 20,000 hours Extended Mode: Up to 30,000 hours Throw Ratio Range 1.38 (Zoom: Wide), 2.19 (Zoom: Tele) Size (Projected Distance) 30" – 150" [0.88 – 4.51 m] (Zoom: Wide) Keystone Correction Manual Vertical: ± 45 degrees; Horizontal: ± 40 degrees Dynamic Contrast Ratio Up to 2,500,000:1 Color Reproduction Up to 16.7 million colors Project from Nearly Any Angle Movement: Left/Right: 180 degrees, Up/Down: 180 degrees; Ball-joint Axis Rotation: 360 degrees Track Compatibility Halo: TEK441, 442, 443 Juno: TEK44FT(Black/White) Global Trac: TEK44-1, 44-2, 44-3, Lens Type Optical zoom (Powered)/Focus (Powered) F-number 1.51 – 1.92 Focal Length 18.2 – 28.4 mm Zoom Ratio 1 – 2.21 (Total), (Optical zoom: 1 – 1.58, Digital zoom: 1 – 1.4) with Media Player .The Rates inclusive of all software, hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per concept. The sound output to match premium cinema theatre level experience. Animation content also included. Qty.: 3 nos. Make-EPSON/Christie/Barco Touchscreen Kisok - Display : 13” FHD display with 10-point multi-touch functionality,Diagonal Size 13",Type Edge LED,Resolution 1920*1080 (Full HD),Pixel Pitch(mm) 0.153 x 0.153 Active Display Area(mm) 293.76 (H) x 165.24 (V),Brightness(Typ.) 300 (w/o Glass) nit,Contrast Ratio 600:1,Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7 M (real 6bit, dither 8bit),Color Gamut 45% Operation Hour 16/7,Haze 10%,Speaker Type,Built in Speaker(5W),Internal Player : Processor Cortex A72 1.7GHz Quad-Core CPU,Storage (FDM),8GB ,Operating System Tizen 4.0 (VDLinux),,inbuilt Processor : Cortex A72 1.7GHz Quad-Core CPU,with 5 year On site warranty. Qty.: 2 nos. Make-Samsung/LG/Panasonic/Delta Mini PC for Info Kisok - Mini PC, Intel NUC i7/16GB/500GB/Win 10 Pro 64bit/Wireless KM/HDMI cable. Qty.: 2 nos. Make-Intel/Dell/HP/ASUS Extended Display - Supplying and installation LED TV with minimum bezel - 65" .Dynamic Crystal Color with Quantum Processor 4K for incredible picture quality,Resolution 3840x2160(16:9),Pixel Pitch(mm) :0.372 x 0.372,Brightness : 700 nits,Contrast Ratio : 4000:1,Color Gamut : 92% (DCI-P3, CIE 1976),Haze Non-Glare,Processor Cortex A72 1.7GHz Quad-Core CPU. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Qty.: 5 nos. Make-Christie,Samsung/LG/Panasonic Headphone - AutoPlay Available,Silver Conduit,8.4mm Cable Thickness,Available with Teardrop or Knuckle Mounting Plate,Fitted with a 90° Swivel Knuckle,With 3.5mm Headphone Jack,Ear Par Materia: Synthetic leather, circumaural ear pads. Qty.: 5 nos. Make-BlackboxAV, Bose or eq Application with UI/UX - Touchscreen Application Make-Custom Special Interactive Effect - Fire Effect which triggered by visitor interactive( Throw a object or touchscreen based) Make-Custom - Fire Sound Effect Make-Custom General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector- 1 6700 lumens - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Make- Christie,Barco, Digital Projection

NS Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty.: 15 nos. Make- Christie,Barco,NEC, Digital Projection Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 6700 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty.: 3 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty.: 7 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty.: 17 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Projector - Supply of DLP Solid state(Laser Phosphor) Projection system with ultra short throw lens 0.25/0.5:1 ratio, having 5000 Lumens, 3D available, 1920 x 1200 Native Resolution,1800:1 Contrast Ratio, Lamp Life 20000 hours, Inputs: HDMI/HDBaseT/VGA,Audio in; & projector mountin bracket etc. Qty.: 6 nos. Make- Christie,Barco,NEC, Digital Projection Media Server - Display media server/Workstation with 4K outputs as required , synced together. It should be capable of capturing content.Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB(For WINDOWS BOOT), HDD: 2 TB , Nvidia Quadro GFX, 8GB, 3DP, Windows 10 Pro 64 Bi or higher config.It should also have genlock and framelock capability. Should also have Art-net Ethernet in/out. to complete the job with all respects. Qty. : 2 nos. Make-Dell/HP/ASUS Mapping Software - 3D Projection mapping software, Playback control System to manage, schedule and control the media severs. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software. to complete the job with all respects. Qty.: 6 nos. Make- Dataton/Coolux/Pixera/Vioso/Equivalent Acessories - Transmitters- Recievers over CAT6 upoto 100 meter, CAT 6 cables,Connectors, Network Rack with acessories,Patch Panel network switch, and other accessories to required to make it fuctional Make-KRAMER/ATLONA/Dlink/Netrack/Comrack Projector - Supply of 1-chip DLP LASER Phosphor Multimedia Projection system having, 9600 Lumens 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3000000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 0.65-0.75 lens & projector mountin bracket etc. complete with installation as per the site requirement. Qty.: 2 nos. Make- Christie,Barco,NEC, Digital Projection General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Server System - Processor family Intel® i9 10th Gen, Rack Mountable workstation with 5 Year Onsite Warranty RAM- 32GB DDR4,SSD- 1TB, HDD: 2 TB , Nvidia Quadro RTX4000, 8GB, 3DP, Windows 10 Pro 64 Bit . Qty : 5 nos. Make- Dell/HP/Asus Control Software - Show Control Software. Qty : 1 nos. Make-Medialon, Widget Designer, Pixera or eq Network Part - Display 24" . Qty : 7 nos. Make-Dell/LG/HP Network Part - Layer 3 Gigabit 24 Port with 4 Fibre Port. Qty : 30 nos. Make-Dlink/Comrack Network Part - Firewall Qty : 5 nos. Make-Cisco/Dlink/Comracl Network Part - Patch Panel 24 Port Loaded. Qty : 30 nos. Make-Dlink/Comrack Network Part - SFP Module Qty : 42 nos. Make-Standard Network Part - Keyboard. Qty : 7 nos. Make-Dell/LG/HP Network Part - Mouse Qty : 7 nos. Make-Dell/LG/HP Network Part - Server Rack 42U with accessories. Qty : 7 nos. Make-Comrack/Netrack/Eq Network Part - Cooling Fan Tray. Qty : 7 nos. Make-Comrack/Netrack/Eq Network Part - Rack 4U with accessories. Qty : 7 nos. Make-Comrack/Netrack/Eq Network Part - Rack 6U with accessories. Qty : 9 nos. Make-Comrack/Netrack/Eq Network Part - UPS APC SRC 10KVXI 12V 65AH SMF Battery (Rocket/Exide) Rack & Links Set.(With one hour Power Backup) Qty : 3 nos. Make-APC or Eq Network Part - MS Conduit fittings. Qty : 500 nos. Make-Comrack/Netrack/Eq Network Part - MS Conduit 20 mm. Qty : 1200 nos. Make-Comrack/Netrack/Eq Network Part - I/O Fully Loaded Qty : 250 nos. Make-Comrack/Netrack/Eq Network Part - Cat 6(305M) Qty : 60 nos. Make-Dlink/Comrack Network Part - Connectors RJ 45 Qty : 1500 nos. Make-Dlink/Comrack Network Part - Connectors LC For Fibre. Qty : 75 nos. Make-Dlink/Comrack Network Part - Connectors Sc For Fibre. Qty : 3 nos. Make-Dlink/Comrack Network Part - Optical Fibre 12 Port Patch Panel. Qty : 3 nos. Make-Dlink/Comrack Network Part - Optical Fibre Cable. Qty : 500 m Make-Dlink/Comrack Network Part - MS Cable tray Junction Box. Qty : 20 nos. Make-Comrack/Netrack/Eq Network Part - MS Cable tray 150X50 MM Qty : 500 nos. Make-Comrack/Netrack/Eq Network Part - MS cable tray T. Qty : 50 nos. Make-Comrack/Netrack/Eq Network Part - Installation Fitting Designing Cabling Labour cost Server Configuration IT Infra Establishment and configuration Etc. Job : 7 nos. Make-Standard Network Part - Compatable Dual Band 1GBPS Router. Qty : 2 nos. Make-Netgear/Cisco/Tplink eq Network Part - Access Point. Qty : 100 nos. Make-Cisco/Dlink/Netgear/TPLink or Eq General note - The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary tech equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. - The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate technical socution for the same. All the items required to meet the techonological intent of the installation shall be under the scope of the bidder/execution agency.

NS Gobo Projector - Ceiling Light Projection System RGB liquid crystal shutter projection system Projection Method Direct Mounting, Lighting Track (requires Lighting Track option), Floor Standing (requires Floor Stand option) Driving Method Poly-silicon TFT Active Matrix Pixel Number 1,024,000 dots (1280 x 800) x 3 Color Brightness3 Color Light Output: 2,200 lumens White Brightness3 White Light Output: 2,200 lumens Aspect Ratio 16:10 widescreen Native Resolution WXGA (1280 x 800) Light Source Laser Diode Laser Life1 Normal Mode: Up to 20,000 hours Extended Mode: Up to 30,000 hours Throw Ratio Range 1.38 (Zoom: Wide), 2.19 (Zoom: Tele) Size (Projected Distance) 30" – 150" [0.88 – 4.51 m] (Zoom: Wide) Keystone Correction Manual Vertical: ± 45 degrees; Horizontal: ± 40 degrees Dynamic Contrast Ratio Up to 2,500,000:1 Color Reproduction Up to 16.7 million colors Project from Nearly Any Angle Movement: Left/Right: 180 degrees, Up/Down: 180 degrees; Ball-joint Axis Rotation: 360 degrees Track Compatibility Halo: TEK441, 442, 443 Juno: TEK44FT(Black/White) Global Trac: TEK44-1, 44-2, 44-3, Lens Type Optical zoom (Powered)/Focus (Powered) F-number 1.51 – 1.92 Focal Length 18.2 – 28.4 mm Zoom Ratio 1 – 2.21 (Total), (Optical zoom: 1 – 1.58, Digital zoom: 1 – 1.4) with Media Player .The Rates inclusive of all software, hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per concept. The sound output to match premium cinema theatre level experience. Make-EPSON/Christie/Barco

NS Info Touchscreen Vertical kiosk - 55" - CapacitiveTouchScreen, Diagonal Size 55",Type Edge LED BLU,Resolution 3840*2160 (4K UHD) Pixel Pitch(mm) 0.315 x 0.315,Active Display Area(mm) 1209.6(H) x 680.4(V),Brightness(Typ.):400 (with Touch glass), 500(without Touch Glass) nit Contrast Ratio 4,000:1 (without glass),Viewing Angle(H/V) 178/178,Response Time(G-to-G) 8ms(Typ.),Display Colors 16.7M,Color Gamut 92% (DCI-P3, CIE 1976 Operation Hour, 24/7 Haze,25% (Without Glass),Special Features H/W: Temperature Sensor,Pivot Display, Clock Battery(168hrs Clock Keeping), Built in Speaker(10W 2ch), Video Wall Daisy Chain(HDCP2.2:4EA,HDCP1.4:7EA), IP5x Rating, Wi-Fi/BT S/W: Auto Source Switching & Recovery, LFD Home UI, Button Lock, Hot key option, Plug&Play (Initial Setting) with 5 year onsite warranty. The Rates inclusive of all hardware, electricals, servers, other , necessary cables, networking and any supportive technology required to make it functional as per design. Make-Samsung/LG/Panasonic/Delta

NS Supply, Installation,Testing & Commissioning of Two-Way 6.5" Coaxial Ceiling Loudspeaker. Combined 70V/100V and low impedance direct operation, 50 Watts at 8O nominal setting, 30W multi-tap at 70V/100V, 62 Hz – 20 kHz bandwidth with wide 110° coverage, High 91 dB sensitivity for high maximum SPL. Make JBL Model CONTROL16/CT. Qty.: 20 nos.EXISTING* Make-JBL - Control 16C/T Dual Channel Class D DANTE 480Watts Power amplifier/Dual Channel Class D DANTE 600Watts Power amplifier Distortion, 1/8 rated power <0.1% Signal To Noise Ratio: >101 dBA Channel separation (Crosstalk) >72 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V/ - 2 x 300W @ 4/8ohm & 70V/100V Dante 2 channel Rx Input Transmission High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated/optional Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless Qty.: 2 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/Crown-HArman PoE based Wall mount touch screen controller It should have 2.3" colour touch screen It should have User programmable encoder and button It should be powered via POE powered device It should Support for multiple pages and controls from processor. Qty.: 3 nos. Make-KlarkTeknik / Biamp / Clearone / Symmetrix/BSS 2.5 Sq mm Speaker Cable (as per actual) Qty.: 360 m Make-Belden / Canare / Sommer / Proel Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 180 m Make-Panduit / Commscope / Siemon Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS IP based PoE+ enabled Bi-Amplified loudspeaker/2-way loudspeaker with full compatibility with both Dante and open streaming standards such as AES67 and ST2110-30/can be achive through amplifier. Software allows to configure unlimited number zones, loudspeakers and audio channels, and includes device discovery, a versatile room EQ tool set, system organisation and status monitoring. With option of minimum 100RAL colors to be factory manufactured as per site requirement/can be achive through DSP With Key technologies: Active Crossover, Directivity Control Waveguide, Inteliigent Signal Sensing, Minimum Diffraction Enclosure, Optimized Amplifiers, Protection Circuitry, Reflex Port Design, Room Response Compensation/can be achive through DSP Frequency Response(-6dB):67 Hz -20 kHz/70 Hz - 23 kHz (-10 dB) Sensitivity: 87 dB SPL Peak SPL: 100dB or better Dispersion Angle: H x 100 Degree or better Harmonic Distortion: <0.5%/optional Power Output: Class D Biamplified Circuitary with 25W each for LF & HF/better power output Driver Size: Minimum 3"LF & 0.75" HF Metal Dome Should have minimum 1 x RJ45 for DANTE & PoE+/optional Analog Input on Euroblock connector Complete with Pan Tilt Wall mount bracket from same OEM Qty.: 14 nos. Make-Genlec / Devialet / Tannoy / Adam audio/JBL Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 1150 m Make-Panduit / Commscope / Siemon The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS IP based PoE+ enabled Bi-Amplified loudspeaker/2-way loudspeaker with full compatibility with both Dante and open streaming standards such as AES67 and ST2110-30/can be achive through amplifier. Software allows to configure unlimited number zones, loudspeakers and audio channels, and includes device discovery, a versatile room EQ tool set, system organisation and status monitoring. With option of minimum 100RAL colors to be factory manufactured as per site requirement/can be achive through DSP With Key technologies: Active Crossover, Directivity Control Waveguide, Inteliigent Signal Sensing, Minimum Diffraction Enclosure, Optimized Amplifiers, Protection Circuitry, Reflex Port Design, Room Response Compensation/can be achive through DSP Frequency Response(-6dB): 45Hz-20kHz/37 Hz –18 kHz (-10 dB) Peak SPL: 104dB or more/better SPL 118dB Dispersion Angle: H x 120 Degree/Nominal Coverage Angle 110° H x 85° V, rotatable Harmonic Distortion: <0.5%/Optional Power Output: Class D Biamplified Circuitary with 50W each for LF & HF/better power output Driver Size: Minimum 5"" LF & 0.75"" HF Metal Dome Should have minimum 1 x RJ45 for DANTE &PoE+/Optional Analog Input on Euroblock connector Complete with Pan Tilt Wall mount bracket from same OEM. Qty.: 12 nos. Make-Genlec / Renkus Heinz / Devialet/JBL Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 1130m Make-Panduit / Commscope / Siemon Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS IP based PoE+ enabled Bi-Amplified loudspeaker/2-way loudspeaker with full compatibility with both Dante and open streaming standards such as AES67 and ST2110-30/can be achive through amplifier. Software allows to configure unlimited number zones, loudspeakers and audio channels, and includes device discovery, a versatile room EQ tool set, system organisation and status monitoring. With option of minimum 100RAL colors to be factory manufactured as per site requirement/can be achive through DSPWith Key technologies: Active Crossover, Directivity Control Waveguide, Inteliigent Signal Sensing, Minimum Diffraction Enclosure, Optimized Amplifiers, Protection Circuitry, Reflex Port Design, Room Response Compensation/can be achive through DSPFrequency Response(-6dB):67 Hz -20 kHz/70 Hz - 23 kHz (-10 dB)Sensitivity: 87 dB SPLPeak SPL: 100dB or betterDispersion Angle: H x 100 Degree or betterHarmonic Distortion: <0.5%/optionalPower Output: Class D Biamplified Circuitary with 25W each for LF & HF/better power outputDriver Size: Minimum 3"LF & 0.75" HF Metal DomeShould have minimum 1 x RJ45 for DANTE & PoE+/optionalAnalog Input on Euroblock connectorComplete with Pan Tilt Wall mount bracket from same OEM. Qty.: 10 nos. Make-Genlec / Devialet / Tannoy / Adam audio/JBL DANTE Virtual soundcard for workstation Qty.: 1 nos. Make-Audinet Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 860m Make-Panduit / Commscope / Siemon Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS Supply, Installation,Testing & Commissioning of Two-Way 6.5" Coaxial Ceiling Loudspeaker. Combined 70V/100V and low impedance direct operation, 50 Watts at 8O nominal setting, 30W multi-tap at 70V/100V, 62 Hz – 20 kHz bandwidth with wide 110° coverage, High 91 dB sensitivity for high maximum SPL. Make JBL Model CONTROL16/CT. Qty.: 3 nos. EXISTING* Make-JBL - Control 16C/T Dual Channel Class D DANTE 480Watts Power amplifier/Dual Channel Class D DANTE 600Watts Power amplifier Distortion, 1/8 rated power <0.1% Signal To Noise Ratio: >101 dBA Channel separation (Crosstalk) >72 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V/ - 2x300W @ 4/8ohm & 70V/100V Dante 2 channel Rx Input Transmission High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated/optional Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless. Qty.: 1 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/Crown-Harman 2.5 Sq mm Speaker Cable (as per actual). Qty.: 90 m Make-Belden / Canare / Sommer / Proel The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Immersive point source Speakers Driver Size : 1 x 8" or bigger LF Driver with dual concentric or co-axial HF design Impedance : 8 Ohms Sensitivity : 92 dB or better RMS Power : 120 W or better Maximum SPL Peak - 119dB or better/Maximum SPL (1m) 116 dB Dispersion: 90 degrees conical Frequency Range (-10 dB) : 64 Hz - 20 kHz Enclosure : Enclosure : 15 mm (5/8") plywood, vented and internally braced Powder coated perforated steel grill Multiple Flying suspension point M6 type Qty.: 5 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie/JBL 2. 3-Way Ceiling speaker - Immersive/2-Way Ceiling speaker Speaker Type: Dual Concentric Ceiling Speaker/optional Driver Size : 2 x 5” + 1 x 4.5" LF & 0.8" HF Driver /1 x 6.5" LF & 1 x 0.75" HF Nominal impedance: 8 Ohm Sensitivity: 90dB RMS Power : 70 W Maximum SPL : RMS - 108dB, Peak - 114dB Dispersion: 81° (H) x 101°(V) Degree @ 1KHz Frequency Range (-10 dB) : 60 Hz-20 kHz Enclosure: Plastic with spraying Backcan & Refl ex loaded UL94 V-0 rated ABS Baffle Steel, with weather resistant coating grill Included Accessories : Grille, paint mask, tool kit, screws, plain washer. Qty.: 2 nos. Make-Tannoy / Monitor Audio / Revel / Origin Acoustics / Martin Logan/JBL 3. 4-channel Class D 2000Watt Network amplifier with DSP/4-channel Class D 2400Watt Network amplifier with DSP THD 20Hz-20kHz at 1 W <0.05% Dynamic Range >112 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 500 W @ 2/4 Ohms, 4 × 500 W @ 8 ohms, 4 × 425 W @ 16 ohms - 4 x600W @ 2/4/8 Ohms Max power per channel in case of bridge mode / Power managmenet should be 1600 watts @ 4 ohms and 1100 watts @ 8 ohms 70v/100v Compatible Amplfiier Gain conigurable gain from 22dB to 44 dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 142V with Max output current upto 30Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters Support Multiple make Speaker presets Comprehensive clocking management system with low latency sample rate conversion Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant DANTE network audio inputs 4 Analog Inputs, Control port, Two AES3 digital inputs. Qty.: 2 nos Make-labgruppen / Powersoft / d&b audio technik / Nexo/ JBL 4. DANTE Virtual soundcard for workstation. Qty.: 1 nos. Make-Audinet 5. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 540 m Make-Belden / Canare / Sommer / Proel 6. 20/22 AWG Microphone/Signal Cable ( as per actual) Qty.: 45m Make-Belden / Canare / Sommer / Proel 7. Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 63m Make-Panduit / Commscope / Siemon 8. Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Supply, Installation,Testing & Commissioning of Compact 2-way Loudspeaker with 2 x 8” LF, 2-way loudspeaker system with 1500W Peak , 2x8" LF driver Coverage Pattern = 120° x 60°, Frequency Range = 54 Hz - 20 kHz, SPL =120 dB, System Sensitivity1: 94 dB SPL/1W/1m, Crossover: 2.1 kHz complete with standard accessories as required. Make JBL Model AC28/26+MTU28. Qty.: 3 nos. EXISTING* Make-JBL - AC28/26+MTU28 2. Supply, Installation,Testing & Commissioning of 18 in. High Power Subwoofer, Frequency Range : 28 Hz – 1 kHz, Frequency Response (±3 dB): 35 Hz – 1 kHz Transducer Power : 4800W peak, Maximum SPL :135 peak, System Sensitivity (dB-SPL, 1W @ 1m) :98dB Capable to support Suspension Attachment, "Grille: Powder coated 14 gauge perforated steel, with acoustically transparent, black foam backing", Nominal Impedance: 8 ohms, LF Driver Size " 18 Inch Make JBL Model ASB6118 Qty.: 1 nos. EXISTING* Make-JBL - ASB6118 3. Supply, Installation,Testing & Commissioning of Four Channel Power Amplifier with 4 X 1250W power output. Should have Frequency Response ( 8 Ohms, 20 Hz - 20 kHz): +/- 0.25 dB or better. Signal To Noise Ratio: > 108 dB or better. Voltage Gain:34 dB, Damping Factor (20 Hz to 100 Hz):>1500 complete with standard accessories as required. Make CROWN Model DCi4/1250. Qty.: 1 nos. EXISTING* Make-Crown DCi4/1250 4. Supply, Installation, testing and commissioning of wireless handheld microphone with Premium audio quality, Up to 50 mW RF-output power, 14 hours battery life, Switching bandwidth: 30.5 MHz, RF output power10 or 50 mW, Wideband FM Modulation / Bandwidth, Max. SPL: 144 dB SPL, Audio bandwidth:35 – 20 000 Hz (± 3 dB), T.H.D: 0.7 %, SNR (A-weighted):> 120 dB(A) etc. with complete with standard accessories as required. Make WMS Model 470 VOCAL SET Qty.: 2 nos. EXISTING* Make-AKG - WMS 470 vocal Set 5. Supply, Installation, testing and commissioning of Wireless Lapel Microphone with Extremely light and compact bodypack transmitter, • Up to 50 mW RF-output power, Switching bandwidth: 30.5 MHz (country dependent), Wideband FM Modulation, Audio bandwidth : 35 – 20 000 Hz (± 3 dB), T.H.D.: 0.7 %, SNR (A-weighted):> 120 dB(A), 14 hours battery life (Lithium battery) etc complete with standard accessories as required. Make WMS Model 470 PRESENTER SET Qty.: 1 nos. EXISTING* Make-AKG - WMS 470 Presenter Set 6. Wired Vocal Handheld Microphone for general purpose ELEMENT: Dynamic Pick up Pattern: Hypercardioid/Supercardioid Frequency Response : 40 - 16,000 Hz Impedence : 300 ohms Open Circuit Sensitivity: –55 dB (1.7 mV) re 1V at 1 Pa Output Connector: 3 pin XLR Type Rugged metal construction for long-lasting performance & Rare-earth magnet for improved output and transient response Anti-shock engineering for low handling noise & Multi-stage grille design offers excellent protection against plosives and sibilance without compromising high-frequency clarity. Corrosion-resistant gold-plated XLRM-type connector Accessories Included: Adjustable stand clamp & Soft protective Pouch. Qty.: 2 nos. Make-Audio Technica / Shure / Sennheiser 7. Wired Cardioid Condenser Clip-On Instrument Microphone for instruments ELEMENT: Fixed-charge back plate permanently polarized condenser Pick up Pattern: Cardioid Frequency Response : 40-20,000 Hz Low Frequency Roll-Off: 80 Hz, 12 dB/octave Impedence : 50 ohms Open Circuit Sensitivity: –49 dB (3.5 mV) re 1V at 1 Pa Phantom Power Requirements: 11-52V DC, 3.5 mA typical Maximum Input Sound Level: 149 dB SPL, 1 kHz at 1% T.H.D. Signal to Noise Ratio: 67 dB, 1 kHz at 1 Pa Dynamic Range: (typical) 122 dB, 1 kHz at Max SPL Supplied with Audio-Technica’s versatile UniMount® clip and violin mount It offers a crisp, clear, well-balanced response, even at high SPLs It features an integral 80 Hz high-pass filter on the in-line power module. Qty.: 2 nos. Make-Audio Technica / Shure / Sennheiser /AKG 8. Wired instrument Microphone ELEMENT: Dynamic Pick up Pattern: Hypercardioid/Cardioid Frequency Response : 80 - 17,000 Hz Impedence : 300 ohms Open Circuit Sensitivity: –56 dB (1.5 mV) re 1V at 1 Pa Output Connector: 3 pin XLR Type Corrosion-resistant contacts from gold-plated XLRM-type connector. Special dual-wall floating construction reduces handling noise and assures consistent performance from mic to mic Rugged metal construction for long-lasting performance & neodymium magnet for improved output and transient response. Accessories Included: Adjustable stand clamp & Soft protective Pouch Qty.: 2 nos. Make-Audio Technica / Shure / Sennheiser / AKG 9. Condenser Boundary Microphone Polar Pattern : Cardioid Frequency Response 20-20,000 Hz/50 - 20000 Hz Maximum Input Sound Level:134 dB /120 dB Open Circuit Sensitivity: -34 dB (19.9 mV) re 1V at 1 Pa Signal-to-Noise Ratio : 68 dB Output Connector : Integral 3-pin XLRM-type Includes soft protective pouch Qty.: 2 nos. Make-Audio Technica / Shure / Sennheiser / AKG 10. Digital Mixing Console with DANTE Interface Microphone Preamplifier inputs - 16 or better Mix Buses 25 Aux Inputs/Outputs 6/6 AES50 or equiavonet stage box connectivity Ports - 2 or more Monitoring Outputs 2/2 Input Processing Channels 32 Input Channels, 8 Aux Channels, 8 FX Return Channels Output Processing Channels: 8 16 aux buses, 6 matrices Internal Effects Engines (True Stereo / Mono) 8 / 16 Signal Processing 40-Bit Floating Point 192 kHz ADC and DAC converters for outstanding audio performance A/D Conversion 24-Bit, 112 dB Dynamic Range D/A Conversion 24-Bit, 120 dB Dynamic Range 32 channel bidirectional MultiTarck Recording and playback on SD/SDHC cards MIDI Inputs / Outputs 1/1 Display 5" TFT LCD Complete with stage box with 16 Inputs 8 Outputs from same OEM. With Digital audio and control connectivity with digital audio networking. Qty.: 1 set Make-Audio Technica / Shure / Sennheiser / AKG 11. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 270 nos. Make-Midas /Avid /Digico / SSL/Soundcraft 12. 20/22 AWG Microphone/Signal Cable ( as per actual) Qty.: 270 nos. Make-Belden / Canare / Sommer / Proel 13. Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 162 nos. Make-Panduit / Commscope / Siemon 14. Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. LCR Speaker Driver Size : 1 x 8" or bigger LF Driver with dual concentric or co-axial HF design Impedance : 8 Ohms Sensitivity : 92 dB or better RMS Power : 120 W or better Maximum SPL Peak - 119dB or better/Maximum SPL (1m) 116 dB Dispersion: 90 degrees conical Frequency Range (-10 dB) : 64 Hz - 20 kHz Enclosure : Enclosure : 15 mm (5/8") plywood, vented and internally braced Powder coated perforated steel grill Multiple Flying suspension point M6 type Qty.: 3 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie'/ JBL 2. 3-Way Ceiling speaker - Immersive/2-Way Ceiling speaker Speaker Type: Dual Concentric Ceiling Speaker/optional Driver Size : 2 x 5” + 1 x 4.5" LF & 0.8" HF Driver /1 x 6.5" LF & 1 x 0.75" HF Nominal impedance: 8 Ohm Sensitivity: 90dB RMS Power : 70 W Maximum SPL : RMS - 108dB, Peak - 114dB Dispersion: 81° (H) x 101°(V) Degree @ 1KHz Frequency Range (-10 dB) : 60 Hz-20 kHz Enclosure: Plastic with spraying Backcan & Refl ex loaded UL94 V-0 rated ABS Baffle Steel, with weather resistant coating grill Included Accessories : Grille, paint mask, tool kit, screws, plain washer Qty.: 4 nos. Make-Tannoy / Monitor Audio / Revel / Origin Acoustics / Martin Logan/ JBL 3. Subwoofer - Passive 12" Direct Radiating Subwoofer Driver Size : 1 x 12" LF Driver Impedance : 8 Ohms Sensitivity : 97 dB or better RMS Power : 250 W RMS or better Maximum SPL : Peak - 127dB or better Frequency Response (±3 dB): 40 Hz – 120 Hz Enclosure : 11 ply birch plywood 16 GA powder-coated, plated steel grill Multiple Flying suspension point M10 type. Qty.: 2 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie/JBL 4. 4-channel Class D 2000Watt Network amplifier with DSP/4-channel Class D 2400Watt Network amplifier with DSP THD 20Hz-20kHz at 1 W <0.05% Dynamic Range >112 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 500 W @ 2/4 Ohms, 4 × 500 W @ 8 ohms, 4 × 425 W @ 16 ohms - 4 x600W @ 2/4/8 Ohms Max power per channel in case of bridge mode / Power managmenet should be 1600 watts @ 4 ohms and 1100 watts @ 8 ohms 70v/100v Compatible Amplfiier Gain conigurable gain from 22dB to 44 dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 142V with Max output current upto 30Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters Support Multiple make Speaker presets Comprehensive clocking management system with low latency sample rate conversion Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant DANTE network audio inputs 4 Analog Inputs, Control port, Two AES3 digital inputs. Qty.: 2 nos. Make-labgruppen / Powersoft / d&b audio technik / Nexo/Crown-Harman 5. PoE based Wall mount touch screen controller It should have 2.3" colour touch screen It should have User programmable encoder and button It should be powered via POE powered device It should Support for multiple pages and controls from processor. Qty.: 1 nos. Make-KlarkTeknik / Biamp / Clearone / Symmetrix/BSS 6. DANTE Virtual soundcard for workstation. Qty.: 1 nos. Make-Audinet 7. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 450m Make-Belden / Canare / Sommer / Proel 8. 20/22 AWG Microphone/Signal Cable ( as per actual) Qty.: 45m Make-Belden / Canare / Sommer / Proel 9. Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 63m Make-Panduit / Commscope / Siemon 10. Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS Inwall speakers: Dual 6" In-Wall speaker/ single 6.5" Driver Size : 2 x 6.5” LF & 1 x 1" HF driver/ 1x 6.5" LF, 1 x 1" HF Nominal impedance: 8 Ohm Sensitivity : 92dB/88 dB SPL RMS Power : 80 Watts or better Maximum SPL : RMS - 111dB , Peak - 117dB Frequency Range (-10 dB) : 40 Hz - 20 kHz Enclosure : Baffle panel: moulded UV Resistant ABS Powder coated perforated steel grill- grill should be paintaible to match interior decor Qty.: 9 nos. Make-Tannoy / Focal / Martin Logan / Defintive Technology / Bose/JBL In-Wall subwoofers: Dual 6" In-Wall subwoofer/ dual 10" wall mount subwoofer Driver Size: 2 x 6.5” driver/2 x 10" driver Nominal impedance: 4 Ohm/ 8O Sensitivity : 94dB RMS Power : 160 W or better Maximum SPL : RMS - 116dB , Peak - 122dB Frequency Range (-10 dB) : 29 Hz - 110 Hz/38 Hz - 500 Hz Enclosure : Baffle panel: moulded UV Resistant ABS Powder coated perforated steel grill- grill should be paintaible to match interior decor Qty.: 3 nos. Make-Tannoy / Focal / Martin Logan / Defintive Technology / Bose/JBL DANTE Virtual soundcard for workstation. Qty.: 1 nos. Make-Audinet Dual Channel Class D DANTE 480Watts Power amplifier/Dual Channel Class D DANTE 600Watts Power amplifier Distortion, 1/8 rated power <0.1% Signal To Noise Ratio: >101 dBA Channel separation (Crosstalk) >72 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V/ - 2x300W @ 4/8ohm & 70V/100V Dante 2 channel Rx Input Transmission High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated/optional Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless. Qty.: 4 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/Crown-Harman Supply, Installation,Testing & Commissioning of Eight Channel Power Amplifier with 8 X 300W power output. Should have Frequency Response ( 8 Ohms, 20 Hz - 20 kHz):+/- 0.25 dB, Signal To Noise Ratio:> 108 dB, Voltage Gain:34 dB, Damping Factor (20 Hz to 100 Hz):>1000 Complete with standard accessories as required. Make CROWN Model DCi8/300. Qty.: 1 nos. Make-Crown DCI8/300 Dante Output expander - 4 channel Qty.: 1 nos. Make-RDL / QSC / Symetrix / Klarkteknik 2.5 Sq mm Speaker Cable (as per actual) Qty.: 800 m Make-Belden / Canare / Sommer / Proel Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 63 m Make-Panduit / Commscope / Siemon Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS Supply, Installation,Testing & Commissioning of Two-Way 6.5" Coaxial Ceiling Loudspeaker. Combined 70V/100V and low impedance direct operation, 50 Watts at 8O nominal setting, 30W multi-tap at 70V/100V, 62 Hz – 20 kHz bandwidth with wide 110° coverage, High 91 dB sensitivity for high maximum SPL. Make JBL Model CONTROL16/CT. Qty.: 5 nos. EXISITING* Make-JBL - Control 16C/T Supply Installation Testing & Commissioning of Dual channel 2X 150Watt Digital Power Amplifier. Power @8om-2x150W,Power@ 4om-2X250W,Frequency Response-20Hz-20KHz(+0,-0.5dB),THD+N- 0.05%,Siew Rate-25V/us,Damping Factor->100,Output Circuitry-Class AB,Signal to Noise Ratio- 85dB,Cross Talk- 60dB,Input Impedance-0.7V,Cooling-Two variable speed fans,Amplifier Protection-Short circuit, themal, over load, chip limiter, DC voltage Make-Harman(JBL). Qty.: 2 nos. EXISITING* Make-model to be confiremd by Customer 4x4 USB 2.0 Audio/MIDI Interface- 24-Bit/192 kHz resolution for professional audio quality, Compatible with popular recording software including Avid Pro Tools*, Ableton Live*, Steinberg Cubase*, etc. Streams 4 inputs / 4 outputs plus 1x MIDI I/O. Input/Playback Mix control and Stereo/Mono switch for direct monitoring. Status, Signal and Clip indications for perfect overview. Main Outputs on balanced XLR and 1/4" TRS connectors. Qty.: 1 nos. Make-Behringer / Presonus / Steinberg / Focusrite 2.5 Sq mm Speaker Cable (as per actual) Qty.: 180m Make-Belden / Canare / Sommer / Proel Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1.Supply Installation Testing & Commissioning of Two-Way 8-Inch Coaxial Ceiling Loudspeaker consisting of a 200 mm (8.0 inch) high tech cone driver and a 25 mm soft-dome liquid cooled tweeter mounted in a vented. Should have Frequency Response (-10dB):58 Hz – 20 kHz, Sensitivity:92 dB (1kHz - 16 kHz), Coverage Angle:90° conical, Maximum SPL (1m):118 dB peak, Impedance:8 ohms. Should be supplied complete with standard accessories as required. Make JBL Model CONTROL 18C/T. Qty.: 7 nos. EXISITING* Make-JBL - Control18CT 2.Supply Installation Testing & Commissioning of Dual channel 2X 150Watt Digital Power Amplifier. Power @8om-2x150W,Power@ 4om-2X250W,Frequency Response-20Hz-20KHz(+0,-0.5dB),THD+N- 0.05%,Siew Rate-25V/us,Damping Factor->100,Output Circuitry-Class AB,Signal to Noise Ratio- 85dB,Cross Talk- 60dB,Input Impedance-0.7V,Cooling-Two variable speed fans,Amplifier Protection-Short circuit, themal, over load, chip limiter, DC voltage Make-Harman(JBL). Qty.: 2 nos. EXISITING* Make-model to be confiremd by Customer 3.4x4 USB 2.0 Audio/MIDI Interface- 24-Bit/192 kHz resolution for professional audio quality, Compatible with popular recording software including Avid Pro Tools*, Ableton Live*, Steinberg Cubase*, etc. Streams 4 inputs / 4 outputs plus 1x MIDI I/O. Input/Playback Mix control and Stereo/Mono switch for direct monitoring. Status, Signal and Clip indications for perfect overview. Main Outputs on balanced XLR and 1/4" TRS connectors. Qty.: 1 nos. Make-Behringer / Presonus / Steinberg / Focusrite 4.2.5 Sq mm Speaker Cable (as per actual) . Qty.: 180 m Make-Belden / Canare / Sommer / Proel 5.Various Audio Connectors to complete the system. Qty.: 1 nos. Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1.Supply installation testing and commissioning of two way wall mount speaker Built-in 70V & 100V transformer 8"+2" Economy range speaker of excellent sound quality Power taps 5W/10W/20W/40W/80W @100V outout Both 100V and 80hm outputs Fashion speaker of black color Make-Harman(JBL). Qty.: 9 nos. EXISITING* Make-JBL - Control28 (model to be confiremd by Customer 2.Supply, Installation,Testing & Commissioning of Two-Way 6.5" Coaxial Ceiling Loudspeaker. Combined 70V/100V and low impedance direct operation, 50 Watts at 8O nominal setting, 30W multi-tap at 70V/100V, 62 Hz – 20 kHz bandwidth with wide 110° coverage, High 91 dB sensitivity for high maximum SPL. Make JBL Model CONTROL16/CT. Qty.: 27 nos. EXISITING* Make-JBL - Control 16C/T 3.Supply, Installation,Testing & Commissioning of Multichannel Digital Network Based Power Amplifier with Power output 8 x 600W @ 4 Ohms / 8 Ohms. Eight-channel Audio amplifier , 8x 600W at 4 and 8 Ohm, 70Vrms and 100Vrms output on all Eight channels THD (at full rated power, 20Hz - 20kHz) =0.35%, Cooling Continuously variable speed forced air, Voltage Gain Max level= 34dB, Audio Digital channel bus compatibility up to 8 channel, bridgeable channels - even in 100Vrms mode, 2 digital audio bus RJ 45 port, 1 Ethernet R 45 port for monitoring and configuration. Should have Limiters, Input/output EQ, Delay, Matrix Mixer, Speaker Line Monitoring, Damping Factor (20 Hz to 100 Hz) : >1000 Complete with standard accessories as required. Make CROWN Model DCi8/600DA. Qty.: 1 nos. EXISITING* Make-Crwon - DCI8/600DA 4.2.5 Sq mm Speaker Cable (as per actual) Make-Belden / Canare / Sommer / Proel The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1.Supply Installation Testing & Commissioning of Two-Way 8-Inch Coaxial Ceiling Loudspeaker consisting of a 200 mm (8.0 inch) high tech cone driver and a 25 mm soft-dome liquid cooled tweeter mounted in a vented. Should have Frequency Response (-10dB):58 Hz – 20 kHz, Sensitivity:92 dB (1kHz - 16 kHz), Coverage Angle:90° conical, Maximum SPL (1m):118 dB peak, Impedance:8 ohms. Should be supplied complete with standard accessories as required. Make JBL Model CONTROL 18C/T. Qty.: 7 nos. EXISITING* Make-JBL - Control18CT 2.Supply, Installation, testing and commissioning of 2 Channel Power Amplifier delivering 300 W power per channel. Analog Input Signal to Noise Ratio (ref. rated power, 100V, 20Hz - 20kHz) at 8 ohms):> 104dB, THD (full rated power, 20 Hz - 20 kHz): 0.35%, Damping Factor (20 Hz to 100 Hz):> 1000, Frequency Response (8O, 20 Hz - 20 kHz):+/-0.5dB, Crosstalk:> 80dB Complete with standard accessories as required. Make CROWN Model CDi2/300. Qty.: 1 nos. EXISITING* Make-Crown - CDi2/300 3.Dante Interface module with 2 x Analog outputs Make-KlarkTeknik / Biamp / Clearone / Symmetrix 4.PoE based Wall mount touch screen controller It should have 2.3" colour touch screen It should have User programmable encoder and button It should be powered via POE powered device It should Support for multiple pages and controls from processor. Qty.: 3 nos. Make-KlarkTeknik / Biamp / Clearone / Symmetrix/BSS 5.Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 72m Make-Panduit / Commscope / Siemon 6. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 180m Make-Belden / Canare / Sommer / Proel The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1.Pedisterion Sound System SITC of Outdoor / IN-Ground Speaker complying to following:-Weather-proof 5-position tap switch for 25/70.7/100 Volt, Frequency Response of 62 Hz – 22 kHz, 32 / 16 / 8 Watt, UV-, scratch- and weather-resistant, Suitable for high quality Music, corrosion- and theft-resistant mounting hardware, IP 55 rated, tested in accordance to IEC60268 - Part 5 for high quality intelligibility complete with necessary mounting hardware & accesories, Applicable for Indoor and outdoor usescomplete with necessary mounting hardware & accesories.Make-Harman(JBL). Qty.: 58 nos. EXISITING* Make-JBL - Control 85 2.250W Four Channel Class-D Amplifier with following features:- 250W RMS per Channel, Amplifier output 100V/70V/4 Ohm, Supply input AC 110/230V-50Hz DC 24V, Short circuit protection, thermal & Electronic protoction. Cooling fans, Efficiency > 90%, AC & DC fuses, SNR > 90 dB .Make-Harman(JBL). Qty.: 3 nos. EXISITING* Make-Crown- Model to be confirmed by Customer 3.2.5 Sq mm Speaker Cable (as per actual) Qty.: 2160 m Make-Belden / Canare / Sommer / Proel 4.Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Professional Studio grade Closed-back dynamic over ear headphone Driver Diameter - 40 mm or better Frequency Response: 15 - 20,000 Hz Maximum Input Power: 700 mW at 1 kHz Sensitivity: 96 dB or better Impedance: 47 ohms Cable: 3.0 m (9.8'), straight, left-side exit Magnet: Neodymium Voice Coil: Copper-clad aluminum wire Folding/collapsible: Yes Accessories Included: 6.3 mm (1/4") snap-on adapter. Qty.: 27 nos. Make-Audio Technica / Bose / Focal / Beyerdynamic/AKG 2. Headphone Aamplfier - 4 channel stero headphoen amplifier with maximum input level of upto +15dBU, 1/4" TRS connector, stereo input and output connectors. Qty.: 18 nos. Make-Behringer / Presonus / Art / Focusrite 3. Supply, Installation,Testing & Commissioning of Two-Way 6.5" Coaxial Ceiling Loudspeaker. Combined 70V/100V and low impedance direct operation, 50 Watts at 8O nominal setting, 30W multi-tap at 70V/100V, 62 Hz – 20 kHz bandwidth with wide 110° coverage, High 91 dB sensitivity for high maximum SPL. Make JBL Model CONTROL16/CT. Qty.: 18 nos. EXISITING* Make-JBL - Control 16C/T 4. Dual Channel Class D DANTE 480Watts Power amplifier/Dual Channel Class D DANTE 600Watts Power amplifier Distortion, 1/8 rated power <0.1% Signal To Noise Ratio: >101 dBA Channel separation (Crosstalk) >72 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V/ - 2x300W @ 4/8ohm & 70V/100V Dante 2 channel Rx Input Transmission High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated/optional Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless Qty.: 1 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/Crown-Harman 5. DANTE Virtual soundcard for workstation. Qty.: 1 nos. Make-Audinet 6. PoE based Wall mount touch screen controller It should have 2.3" colour touch screen It should have User programmable encoder and button It should be powered via POE powered device It should Support for multiple pages and controls from processor. Qty.: 1 nos. Make-KlarkTeknik / Biamp / Clearone / Symmetrix/BSS 7. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 360m Make-Belden / Canare / Sommer / Proel 8. 20/22 AWG Microphone/Signal Cable ( as per actual) Qty.: 45m Make-Belden / Canare / Sommer / Proel 9. Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 63 nos. Make-Panduit / Commscope / Siemon 10. Various Audio Connectors to complete the system. Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Supply Installation Testing & Commissioning of Two-Way 8-Inch Coaxial Ceiling Loudspeaker consisting of a 200 mm (8.0 inch) high tech cone driver and a 25 mm soft-dome liquid cooled tweeter mounted in a vented. Should have Frequency Response (-10dB):58 Hz – 20 kHz, Sensitivity:92 dB (1kHz - 16 kHz), Coverage Angle:90° conical, Maximum SPL (1m):118 dB peak, Impedance:8 ohms. Should be supplied complete with standard accessories as required. Make JBL Model CONTROL 18C/T. Qty.:6 nos. EXISTING* Make-JBL - Control18CT 2. Inwall speakers: Dual 6" In-Wall speaker/ single 6.5" Driver Size : 2 x 6.5” LF & 1 x 1" HF driver/ 1x 6.5" LF, 1 x 1" HF Nominal impedance: 8 Ohm Sensitivity : 92dB/88 dB SPL RMS Power : 80 Watts or better Maximum SPL : RMS - 111dB , Peak - 117dB Frequency Range (-10 dB) : 40 Hz - 20 kHz Enclosure : Baffle panel: moulded UV Resistant ABS Powder coated perforated steel grill- grill should be paintaible to match interior decor. Qty.: 4 nos. Make-Tannoy / Focal / Martin Logan / Defintive Technology / Bose 3. Dual Channel Class D DANTE 480Watts Power amplifier/Dual Channel Class D DANTE 600Watts Power amplifier Distortion, 1/8 rated power <0.1% Signal To Noise Ratio: >101 dBA Channel separation (Crosstalk) >72 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V/ - 2x300W @ 4/8ohm & 70V/100V Dante 2 channel Rx Input Transmission High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated/optional Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless Qty.: 2 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/ JBL 4. 2.5 Sq mm Speaker Cable (as per actual). Qty.:360m Make-Belden / Canare / Sommer / Proel 5. Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 63 m Make-Panduit / Commscope / Siemon 6. Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Immersive point source Speakers Driver Size : 1 x 8" or bigger LF Driver with dual concentric or co-axial HF design Impedance : 8 Ohms Sensitivity : 92 dB or better RMS Power : 120 W or better Maximum SPL Peak - 119dB or better/Maximum SPL (1m) 116 dB Dispersion: 90 degrees conical Frequency Range (-10 dB) : 64 Hz - 20 kHz Enclosure : Enclosure : 15 mm (5/8") plywood, vented and internally braced Powder coated perforated steel grill Multiple Flying suspension point M6 type. Qty.: 4 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie/ JBL 2. 3-Way Ceiling speaker - Immersive Speaker Type: Dual Concentric Ceiling Speaker Driver Size : 2 x 5” + 1 x 4.5" LF & 0.8" HF Driver Nominal impedance: 8 Ohm Sensitivity: 90dB RMS Power : 70 W Maximum SPL : RMS - 108dB, Peak - 114dB Dispersion: 81° (H) x 101°(V) Degree @ 1KHz Frequency Range (-10 dB) : 60 Hz-20 kHz Enclosure: Plastic with spraying Backcan & Refl ex loaded UL94 V-0 rated ABS Baffle Steel, with weather resistant coating grill Included Accessories : Grille, paint mask, tool kit, screws, plain washer. Qty.: 4 nos. Make-Tannoy / Monitor Audio / Revel / Origin Acoustics / Martin Loga/ JBL 3. 4-channel Class D 2000Watt Network amplifier with DSP/4-channel Class D 2400Watt Network amplifier with DSP THD 20Hz-20kHz at 1 W <0.05% Dynamic Range >112 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 500 W @ 2/4 Ohms, 4 × 500 W @ 8 ohms, 4 × 425 W @ 16 ohms - 4 x600W @ 2/4/8 Ohms Max power per channel in case of bridge mode / Power managmenet should be 1600 watts @ 4 ohms and 1100 watts @ 8 ohms 70v/100v Compatible Amplfiier Gain conigurable gain from 22dB to 44 dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 142V with Max output current upto 30Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters Support Multiple make Speaker presets Comprehensive clocking management system with low latency sample rate conversion Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant DANTE network audio inputs 4 Analog Inputs, Control port, Two AES3 digital inputs. Qty.: 2 nos. Make-labgruppen / Powersoft / d&b audio technik / Nexo/ Crown-Harman 4. DANTE Virtual soundcard for workstation. Qty.: 1 nos. Make-Audinet 5. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 540 m Make-Belden / Canare / Sommer / Proel 6. 20/22 AWG Microphone/Signal Cable ( as per actual) Qty.: 45m Make-Belden / Canare / Sommer / Proel 7. Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 63m Make-Panduit / Commscope / Siemon 8. Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. 8" Ceiling speaker with very tight coverge pattern Driver Size : 1 x 8” driver with dual concentric or co-axial design/1 x 8" driver Sensitivity : 93dB/92 dB RMS Power : 90 W or better In-built transformer Tap : 100V / 70V upto 60W Maximum SPL : RMS - 113dB , Peak - 119dB/118dB Peak Dispersion: 60 Degree Conical or lesser Frequency Range (-10 dB) : 40 Hz - 20 kHz/58 Hz – 20 kHz Certification: UL 94V-0, UL-1480, UL-2043, CE Enclosure : Zinc plated steel Steel, with weather resistant coating grill Included Accessories: C-Ring, tile-bridge kit, paint mask, cut-out template, grille. Qty.: 4 nos. Make-Tannoy / Focal / Martin Logan / Defintive Technology / Bose/ JBL 2. 2-channel Class D 800Watt power amplifier/Dual Channel Class 600Watts Power amplifier THD 20Hz-20kHz at 1 W <0.1% Signal To Noise Ratio >112 dB Channel separation at 1 kHz >70 dB Power Handling : 2 × 400 W @ 2 Ohms / 4Ohms / 8 ohms / 16 ohms - 2x600W @ 4/8ohm 70V / 100 V Compatible Max. output current 16 Arms Frequency Response : 10 Hz - 20 kHz Input impedance 20 kOhm Common Mode Rejection (CMR) 50 dB Output impedance 25 mOhm Enerygy Star Rated/optional Cooling : Single fan, front to rear airflow, temperature controlled speed Comprehensive circuit protection and fault indication. Qty.: 1 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/ Crown- Harman 3. 4x4 USB 2.0 Audio/MIDI Interface- 24-Bit/192 kHz resolution for professional audio quality, Compatible with popular recording software including Avid Pro Tools*, Ableton Live*, Steinberg Cubase*, etc. Streams 4 inputs / 4 outputs plus 1x MIDI I/O. Input/Playback Mix control and Stereo/Mono switch for direct monitoring. Status, Signal and Clip indications for perfect overview. Main Outputs on balanced XLR and 1/4" TRS connectors. Qty.: 1 nos. Make-Behringer / Presonus / Steinberg / Focusrite 4. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 360 m Make-Belden / Canare / Sommer / Proel 5. Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Supply installation testing and commissioning of two way wall mount speaker Built-in 70V & 100V transformer 8"+2" Economy range speaker of excellent sound quality Power taps 5W/10W/20W/40W/80W @100V outout Both 100V and 80hm outputs Fashion speaker of black color Make-Harman(JBL). Qty.: 10 nos. EXISTING* Make-JBL - Control28 (model to be confiremd by Customer) 2. Supply, Installation,Testing & Commissioning of Ceilingspeaker 2-way built-in loudspeaker,Power rated-40W/20W/15W/8ohm, “the reference loudspeaker”. It can be used with a standard Hifi amplifier and provides you with a Pro HiFi sound. The loudspeaker has an enforced 6 ½” woofer and 1” tweeter.suitable for the distribution of Back Ground Music.The housing is made of high quality ABS.SPL 1 watt/1 m-92db,SPL Max peak-106db,Frequency Range-60Hz to 20Hz Dispersion @ 1 kH-180Deg,@4KHz-80Deg,@8KHz-45Deg,IP-54 Rated Make-Harman(JBL) Qty.: 10 nos. EXISTING* Make-JBL - (model to be confiremd by Customer) 3. Dual Channel Class D DANTE 480Watts Power amplifier/Dual Channel Class D DANTE 600Watts Power amplifier Distortion, 1/8 rated power <0.1% Signal To Noise Ratio: >101 dBA Channel separation (Crosstalk) >72 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V/ - 2x300W @ 4/8ohm & 70V/100V Dante 2 channel Rx Input Transmission High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated/optional Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless. Qty.: 2 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/ Crown- Harman 4. 2.5 Sq mm Speaker Cable (as per actual). Qty.: 360m Make-Belden / Canare / Sommer / Proel The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Surround Effect Speakers Dual 6" In-Wall speaker/ single 6.5" Driver Size : 2 x 6.5” LF & 1 x 1" HF driver/ 1x 6.5" LF, 1 x 1" HF Nominal impedance: 8 Ohm Sensitivity : 92dB/88 dB SPL RMS Power : 80 Watts or better Maximum SPL : RMS - 111dB , Peak - 117dB Frequency Range (-10 dB) : 40 Hz - 20 kHz Enclosure : Baffle panel: moulded UV Resistant ABS Powder coated perforated steel grill- grill should be paintaible to match interior decor Qty.: 12 nos. Make-Tannoy / Focal / Martin Logan / Defintive Technology / Bose/ JBL 2. Surround Effect Ceiling Speakers: Driver Size : 1 x 8” LF & 1 x 1" HF Driver Nominal impedance: 8 Ohm Sensitivity: 91dB RMS Power : 90 W or better Maximum SPL : RMS - 110dB , Peak - 116dB Dispersion: 100 Degree Conical @ 1kHz Frequency Range (-10 dB) : 65 Hz-20 kHz Certification: UL 94V-0, EN54-24:2008 certified Type A, UL 1480/UL 2043 Enclosure: Steel Backcan Aluminum, powder coated grill Included Accessories: Metal grille, cable gland, flex conduit, C-ring, tile-bridge kit, paint mask, cutout template. Qty.: 4 nos. Make-Tannoy / Martin Audio / Martin Logan / Defintive Technology / Bose/ JBL 3. Surround Effect subwoofers: Dual 6" In-Wall subwoofer/ dual 10" wall mount subwoofer Driver Size: 2 x 6.5” driver/2 x 10" driver Nominal impedance: 4 Ohm/ 8O Sensitivity : 94dB RMS Power : 160 W or better Maximum SPL : RMS - 116dB , Peak - 122dB Frequency Range (-10 dB) : 29 Hz - 110 Hz/38 Hz - 500 Hz Enclosure : Baffle panel: moulded UV Resistant ABS Powder coated perforated steel grill- grill should be paintaible to match interior decor Qty.: 5 nos. Make-Tannoy / Focal / Martin Logan / Defintive Technology / Bose/ JBL 4. Dual Channel Class D DANTE 480Watts Power amplifier/Dual Channel Class D DANTE 600Watts Power amplifier Distortion, 1/8 rated power <0.1% Signal To Noise Ratio: >101 dBA Channel separation (Crosstalk) >72 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V/ - 2x300W @ 4/8ohm & 70V/100V Dante 2 channel Rx Input Transmission High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated/optional Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless Qty.: 8 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/ Crown- Harman 5. 4-channel Class D 2000Watt Network amplifier with DSP/4-channel Class D 2400Watt Network amplifier with DSP THD 20Hz-20kHz at 1 W <0.05% Dynamic Range >112 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 500 W @ 2/4 Ohms, 4 × 500 W @ 8 ohms, 4 × 425 W @ 16 ohms - 4 x600W @ 2/4/8 Ohms Max power per channel in case of bridge mode / Power managmenet should be 1600 watts @ 4 ohms and 1100 watts @ 8 ohms 70v/100v Compatible Amplfiier Gain conigurable gain from 22dB to 44 dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 142V with Max output current upto 30Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters Support Multiple make Speaker presets Comprehensive clocking management system with low latency sample rate conversion Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant DANTE network audio inputs 4 Analog Inputs, Control port, Two AES3 digital inputs Qty.: 2 nos. Make-labgruppen / Powersoft / d&b audio technik / Nexo/ Crown-Harman 6. PoE based Wall mount touch screen controller It should have 2.3" colour touch screen It should have User programmable encoder and button It should be powered via POE powered device It should Support for multiple pages and controls from processor Qty.: 1 nos. Make-KlarkTeknik / Biamp / Clearone / Symmetrix/ BSS 7. DANTE Virtual soundcard for workstation Qty.: 1 nos. Make-Audinet 8. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 810 m Make-Belden / Canare / Sommer / Proel 9. 20/22 AWG Microphone/Signal Cable ( as per actual) Qty.: 45 m Make-Belden / Canare / Sommer / Proel 10. Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 63 m Make-Panduit / Commscope / Siemon 11. Various Audio Connectors to complete the system. Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Immersive point source Speakers Driver Size : 1 x 8" or bigger LF Driver with dual concentric or co-axial HF design Impedance : 8 Ohms Sensitivity : 92 dB or better RMS Power : 120 W or better Maximum SPL Peak - 119dB or better/Maximum SPL (1m) 116 dB Dispersion: 90 degrees conical Frequency Range (-10 dB) : 64 Hz - 20 kHz Enclosure : Enclosure : 15 mm (5/8") plywood, vented and internally braced Powder coated perforated steel grill Multiple Flying suspension point M6 type. Qty.: 7 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie/ JBL 2. Subwoofer - Passive 12" Direct Radiating Subwoofer Driver Size : 1 x 12" LF Driver Impedance : 8 Ohms Sensitivity : 97 dB or better RMS Power : 250 W RMS or better Maximum SPL : Peak - 127dB or better Frequency Response (±3 dB): 40 Hz – 120 Hz Enclosure : 11 ply birch plywood 16 GA powder-coated, plated steel grill Multiple Flying suspension point M10 type. Qty.: 2 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie/ JBL 3. 4-channel Class D 2000Watt Network amplifier with DSP/4-channel Class D 2400Watt Network amplifier with DSP THD 20Hz-20kHz at 1 W <0.05% Dynamic Range >112 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 500 W @ 2/4 Ohms, 4 × 500 W @ 8 ohms, 4 × 425 W @ 16 ohms - 4 x600W @ 2/4/8 Ohms Max power per channel in case of bridge mode / Power managmenet should be 1600 watts @ 4 ohms and 1100 watts @ 8 ohms 70v/100v Compatible Amplfiier Gain conigurable gain from 22dB to 44 dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 142V with Max output current upto 30Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters Support Multiple make Speaker presets Comprehensive clocking management system with low latency sample rate conversion Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant DANTE network audio inputs 4 Analog Inputs, Control port, Two AES3 digital inputs Qty.: 3 nos. Make-labgruppen / Powersoft / d&b audio technik / Nexo/ Crown-Harman 4. PoE based Wall mount touch screen controller It should have 2.3" colour touch screen It should have User programmable encoder and button It should be powered via POE powered device It should Support for multiple pages and controls from processor. Qty.: 1 nos. Make-KlarkTeknik / Biamp / Clearone / Symmetrix 5. DANTE Virtual soundcard for workstation Qty.: 1 nos. Make-Audinet 6. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 540 m Make-Belden / Canare / Sommer / Proel 7. 20/22 AWG Microphone/Signal Cable ( as per actual) Qty.: 45 m Make-Belden / Canare / Sommer / Proel 8. Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 63 m Make-Panduit / Commscope / Siemon 9. Various Audio Connectors to complete the system. Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Multi-purpose two way speakers - can be used as In-Ceiling, Wall / Surface Mount or Pendent Mount as per site requrements. Driver size: 2.25" 2-Way Frequency Range: 140Hz - 20kHz Dispersion: 130°, 2kHz Octave Band Sensitivity: 81.6dB (1W/1m) or better Maximum SPL (1m): 103 dB Peak Power Taps 70/100V - upto 8 watts. Can be connected to any 70V / 100V amplifier or the speakers can be connected using Cat5e cable. Each speaker features "in" and "out" Cat5e terminals making it easy to daisy chain speakers to the source unit. complete with Flange, Diffuser and Lens Kits./Input Connectors Removable locking 4-pin connector with screw-down terminals Qty.: 7 pairs Make-AtlasIED / Cambridge Audio / Tannoy / Sonanace/ JBL 2. Dual Channel Class D 480Watts Power amplifier/ Dual channel Class D 600Watt Network amplifier with DSP Distortion, 1/8 rated power <0.05% Signal To Noise Ratio: >97 dBA Channel separation (Crosstalk) >85 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V - 2x600W @ 4/8ohm Maximum input level 9.75 V (+22 dBu) High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz Input impedance 10 kO unbalanced and RCA, 20 kO balanced GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless Qty.: 2 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/ Crown- Harman 3. Effect Speakers: 4" In-Wall speaker Driver Size : 1 x 4” driver with dual concentric or co-axial Nominal impedance: 8 Ohm Sensitivity : 88dB RMS Power : 60 W Maximum SPL : RMS - 106dB , Peak - 112dB Frequency Range (-10 dB) : 73 Hz - 20 kHz Enclosure : Baffle panel: moulded UV Resistant ABS Powder coated perforated steel grill- grill should be paintaible to match interior decor. Qty.: 9 nos. Make-Tannoy / Focal / Martin Logan / Defintive Technology / Bose 4. 2x2 USB 2.0 Audio Interface- 48 kHz resolution for professional audio quality, Compatible with popular recording software including Avid Pro Tools*, Ableton Live*, Steinberg Cubase*, etc. Streams 2 inputs / 2 outputs. Status, Signal and Clip indications for perfect overview. Main Outputs on Phono or XLR connectors. Qty.: 9 nos. Make-Behringer / Presonus / Steinberg / Focusrite 5. Dual Channel Class D 480Watts Power amplifier/ Dual channel Class D 600Watt Network amplifier with DSP Distortion, 1/8 rated power <0.05% Signal To Noise Ratio: >97 dBA Channel separation (Crosstalk) >85 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V Maximum input level 9.75 V (+22 dBu) High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz Input impedance 10 kO unbalanced and RCA, 20 kO balanced GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless Qty.: 5 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/ Crown- Harman 6. Immersive point source Speakers Driver Size : 1 x 8" or bigger LF Driver with dual concentric or co-axial HF design Impedance : 8 Ohms Sensitivity : 92 dB or better RMS Power : 120 W or better Maximum SPL Peak - 119dB or better/Maximum SPL (1m) 116 dB Dispersion: 90 degrees conical Frequency Range (-10 dB) : 64 Hz - 20 kHz Enclosure : Enclosure : 15 mm (5/8") plywood, vented and internally braced Powder coated perforated steel grill Multiple Flying suspension point M6 type. Qty.: 5 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie/ JBL 7. Subwoofer - Passive 12" Direct Radiating Subwoofer Driver Size : 1 x 12" LF Driver Impedance : 8 Ohms Sensitivity : 97 dB or better RMS Power : 250 W RMS or better Maximum SPL : Peak - 127dB or better Frequency Response (±3 dB): 40 Hz – 120 Hz Enclosure : 11 ply birch plywood 16 GA powder-coated, plated steel grill Multiple Flying suspension point M10 type. Qty.: 2 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie/ JBL 8. 4 Channel Class D 1000 watts Power amplifier/ 4-channel Class D 1200Watt Network amplifier with DSP THD 20Hz-20kHz at 1 W <0.1% Signal To Noise Ratio >106 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 250 W @ 2 Ohms / 4Ohms / 8 ohms / 16 ohms -4 x 300W @ 2/4/8 Ohms 70V / 100 V Compatible Max. output current 14 Arms Frequency Response : 10 Hz - 20 kHz Input impedance 20 kOhm Common Mode Rejection (CMR) 50 dB Output impedance 25 mOhm Enerygy Star Rated Cooling : Single fan, front to rear airflow, temperature controlled speed Comprehensive circuit protection and fault indication Qty.: 2 nos. Make-Labgruppen / Powersoft / AtlasIED / LEA Professional/ Crown-Harman 9. Audiophile 24-Bit/96 kHz resolution for professional audio quality Audio Interafce It should have 18x20 USB2.0 Audio/MIDI Interface with ADAT I/O for recording microphones and instruments It should support Streams 18 inputs and 20 outputs of ultra-low latency audio to your computer, supporting Mac* OS X* and Windows XP* or higher It should have 8 state-of-the-art designed Mic Preamplifiers with +48 V phantom power It should have Optical I/Os supporting S/PDIF, ADAT and S/MUX formats up to 96 kHz It Should have Input/Playback Mix control and Stereo/Mono switch for direct monitoring. Qty.: 1 nos. Make-Behringer / Presonus / Steinberg / Focusrite 10. PoE based Wall mount touch screen controller It should have 2.3" colour touch screen It should have User programmable encoder and button It should be powered via POE powered device It should Support for multiple pages and controls from processor. Qty.: 1 nos. Make-KlarkTeknik / Biamp / Clearone / Symmetrix/ BSS 11. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 900m Make-Belden / Canare / Sommer / Proel 12. 20/22 AWG Microphone/Signal Cable ( as per actual) Qty.: 90m Make-Belden / Canare / Sommer / Proel 13. Control & Signal Shielded Twisted Pair Cable(as per actual) Qty.: 275m Make-Panduit / Commscope / Siemon 14. Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. IP based PoE+ enabled Bi-Amplified loudspeaker/2-way loudspeaker with full compatibility with both Dante and open streaming standards such as AES67 and ST2110-30/can be achive through amplifier. Software allows to configure unlimited number zones, loudspeakers and audio channels, and includes device discovery, a versatile room EQ tool set, system organisation and status monitoring. With option of minimum 100RAL colors to be factory manufactured as per site requirement/can be achive through DSP With Key technologies: Active Crossover, Directivity Control Waveguide, Inteliigent Signal Sensing, Minimum Diffraction Enclosure, Optimized Amplifiers, Protection Circuitry, Reflex Port Design, Room Response Compensation/can be achive through DSP Frequency Response(-6dB):67 Hz -20 kHz/70 Hz - 23 kHz (-10 dB) Sensitivity: 87 dB SPL Peak SPL: 100dB or better Dispersion Angle: H x 100 Degree or better Harmonic Distortion: <0.5%/optional Power Output: Class D Biamplified Circuitary with 25W each for LF & HF/better power output Driver Size: Minimum 3"LF & 0.75" HF Metal Dome Should have minimum 1 x RJ45 for DANTE & PoE+/optional Analog Input on Euroblock connector Complete with Pan Tilt Wall mount bracket from same OEM Qty.: 4 nos. Make-Genlec / Renkus Heinz / Devialet 2. Immersive point source Speakers Driver Size : 1 x 8" or bigger LF Driver with dual concentric or co-axial HF design Impedance : 8 Ohms Sensitivity : 92 dB or better RMS Power : 120 W or better Maximum SPL Peak - 119dB or better Dispersion: 90 degrees conical Frequency Range (-10 dB) : 64 Hz - 20 kHz Enclosure : Enclosure : 15 mm (5/8") plywood, vented and internally braced Powder coated perforated steel grill Multiple Flying suspension point M6 type Qty.: 10 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie'/ JBL 3. Subwoofer - Passive 12" Direct Radiating Subwoofer Driver Size : 1 x 12" LF Driver Impedance : 8 Ohms Sensitivity : 97 dB or better RMS Power : 250 W RMS or better Maximum SPL : Peak - 127dB or better Frequency Response (±3 dB): 40 Hz – 120 Hz Enclosure : 11 ply birch plywood 16 GA powder-coated, plated steel grill Multiple Flying suspension point M10 type Qty.: 3 nos. Make-Renkus Heinz / Tannoy / d&b Audio Technik / Christie/ JBL 4. 4-channel Class D 2000Watt Network amplifier with DSP/4-channel Class D 2400Watt Network amplifier with DSP THD 20Hz-20kHz at 1 W <0.05% Dynamic Range >112 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 500 W @ 2/4 Ohms, 4 × 500 W @ 8 ohms, 4 × 425 W @ 16 ohms - 4 x600W @ 2/4/8 Ohms Max power per channel in case of bridge mode / Power managmenet should be 1600 watts @ 4 ohms and 1100 watts @ 8 ohms 70v/100v Compatible Amplfiier Gain conigurable gain from 22dB to 44 dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 142V with Max output current upto 30Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters Support Multiple make Speaker presets Comprehensive clocking management system with low latency sample rate conversion Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant DANTE network audio inputs 4 Analog Inputs, Control port, Two AES3 digital inputs. Qty.: 4 nos. Make-labgruppen / Powersoft / d&b audio technik / Nexo/ JBL 5. 2.5 Sq mm Speaker Cable (as per actual). Qty.: 900 m Make-Belden / Canare / Sommer / Proel 6. 20/22 AWG Microphone/Signal Cable ( as per actual). Qty.: 45 m Make-Belden / Canare / Sommer / Proel 7. Control & Signal Shielded Twisted Pair Cable(as per actual). Qty.: 360 m Make-Panduit / Commscope / Siemon 8. Various Audio Connectors to complete the system Qty.: 360 m Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Jute Installation - This installation is to celebrate the jute and weaving craft of Haryana. The installation have various elements such walls, ceiling and floors made of jute ropes, woven/braided jute as per design. Inclusive of the elements such as: 2. Jute Carpet Flooring - Providing and fixing carpet flooring made of jute hand-woven/braided by the special artist/craftsmen of desired size and thickness in the pattern and shade as per the approval of the design consultant. The carpet to be anti skid, excellent sound insulation,ease to maintain. The rate is inclusive of laying an underlay wherever required and fixing in place with necessary foam backing heavy duty adhesives, doble sided carpet tapes etc all complete as per the direction of engineer in charge. Area : 120 Sqm. 3. Jute Ceiling - Providing and fixing 25x25mm/50x50mm/75x75mm/as per site requirement freestanding M.S. sections of desired thickness tightly wrapped with jute/natural ropes of thickness 5-25mm duly pasted on the sections with adhesives. The ms sections to be fixed horizontally on the ceiling at varied distances parallely and at angles as per the detail drawing and approval of design consultant. The rate is inclusive of coating in one to two coats the mild steel section surface with a base paint/steel primer to avoid rusting. The cost is also inclusive of necessary hardware, clutch wire, fastners etc all complete to install the jute wrapped ms sections in desired pattern to the ceiling/surface as per the satisfaction of engineer incharge. The cost includes coating the jute ropes with two or more coats of paint of desired shades and as per approval. The no. of length of pipe to be used per sqm to be upto 10 lengths of 10 rnft each of assorted length of pipe. The cost is also inclusive of two or more coats of required paint such as duco etc touch up on exposed areas as per approved design. Area : 120 Sqm. 4. Jute wall - Providing and fixing 25x25mm/50x50mm/75x75mm/as per site requirement freestanding M.S. sections of desired thickness tightly wrapped with jute/natural ropes of thickness 5-25mm duly pasted on the sections with adhesives. The ms sections to be fixed from floor to ceiling vertically and at angles on the wall at varied distances. The sections to have provision for T.V.and headphones and excluding the cost of the tv mounting box equipment to be installed as per the detail drawing and approval of design consultant. The rate is inclusive of coating in one to two coats the mild steel section surface with a base paint/steel primer to avoid rusting. The cost is also inclusive of necessary hardware, clutch wire, fastners etc all complete to install the jute wrapped ms sections in desired pattern to the ceiling/surface as per the satisfaction of engineer incharge. The cost includes coating the jute ropes with two or more coats of paint of desired shades and as per approval. The structural stability of the installation to be vetted by the structural consultant of the contractor. The no. of length of pipe to be used per sqm to be upto 10 lengths of 10 rnft each of assorted length of pipe. The cost is also inclusive of two or more coats of required paint such as duco etc touch up on exposed areas as per approved design. Area : 150 Sqm. 5. T.V. Mounting box - Providing and fixing of a wooden T.V. mounting box made of up to 18mm thick plywood with 4-6mm mdf finished in duco paint of approx. size 600x900mm with provision to fix vision glass as per design detail. Inclusive of the cost of vision glass of thickness 6-12mm. Inclusive of all the necessary fittings, fixtures, required for the installation. Qty. 21 6. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. 7. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS 1. Elevator Installation - The installation intends to take the museum visitors through a time travel experience introducing the land of Haryana and its history. The following are the various elements of the installation: 2. Part A- Elevator shell and dome - Providing and fixing 150mm overall thickness curved free standing partition and dome ceiling as per deisgn of up to 10 meter height consisting of 50X50mm 75X75mm or as per site requirements of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm to 18 mm Flexible ply conforming to BWR grade of Greenply/Duroply/Century ply or similar makes on one side having bend radius as little as 100mm , ideal for tight radius work with edge profiles including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, including jointing and finishing to a flush finish with recommended jointing. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The strength of the shell to be approved by the structural engineer of the contractor. The radius of the dome is approximately 5m. The tentative perimeter of the shell to be 34m and the height is 9m. To attain the desired shell shape materials such as foam, sunboard, pop, GI mesh, glasswool to be included. The hollow space to be filled with glasswool to achieve the desired acoustics levels. The indoor curved surface to have projection on it and the cost is to be inclusive of finishing with screen paint 4k high gain Screen paint of even coats by spraying through compressor after primer coat including scrapping, levelling & preparing the surface. Primer coat (Asian/ Nerolac/ Berger) + (minimum) 3 coats to get evenly spread quality finish of approved make, quality & finish shall be provided as directed by Museum Consultants. Finish with wall putti wherever necessary before paint. Please refer to the design presentation for further details. Area: 481 Sqm. 3. Part B- Elevator platform - Providing, fabricating and installation of the elevator platform. The elevator stepped platform of length 14-15m having 3-4 steps of 1200-1500mm width made of metal/wooden base with structure in M.S. frames of approved size, fully equipped with capacity of lifting upto 75-100 people at a time. Each step to have railings of sleek M.S. sections as per approved by the museum design consultants . The platform to be lifted with the lifting mechanism as per suggested by the elevator experts of the contractor as approved by the museum design consultant. The platform and the mechanism to be consulted by an elevator expert. The elevator expert to approve the strength and working of the elevator. The commissioned execution agency is responsible for all the cerifications required. Inclusive of complete integration and functionality. Qty. 1nos. 4. Part C- False Flooring - upto 900mm - Providing and Fixing of False floor with MS tubular section of 50mmX50mm/75mmX75mm/as per requirement of desired thickness with appropriate spacing and necessary welding at junctions including application of 25mm to 32mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to base with 2mm thk MS plate of desired size and base properly welded with all fasteners and necessary hardware's with edge profiles, beadings etc all complete as per approved design. The rate is also inclusive of two coats of MS primer on the frame structure and one to two coats of anti termite oil finish on ply board. Height of False flooring to be considered is 450mm-900mm as per the approval of museum design consultant. Area : 172 sqm. 5. Part D- Sliding Wooden curved Partition - 75mm - Providing and fixing 75 mm overall thickness curved sliding/openable partition up to 4 meter height consisting of 50X50mm/75X75mm/ as per site requirement wooden battens in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions with screws, nails, adhesives and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, electrical conduits, switch boards etc. wherever required. The rate to be inclusive of providing and installing top cover of 12mm to 18 mm Flexible ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws, nails etc all complete as per the direction of engineer in charge. The rate should be inclusive of providing an opening of upto 3000mm wide and 2500mm in height with an automated opening mechanism that should seamless in visual and audio should be synced with the AV content played in the insallation for opening and closing with necessary fixtures, fittings, hardware, hanging system, electrical, mechanical,sliding rails,remort control or any other mechanism required to make it functional all complete as per the direction of engineer in charge. Qty. : 2nos. 6. Carpet Flooring - Carpet:Providing & Laying approved shade of acid stain resistant Carpet Tiles/flooring of 4-5 mm thickness with waterproof backing , installed in area demarked in detail drawings over vertical/horrizontal surface and as per company specifications with the Engineer in charge. Make :(Armstrong, Euronics, Geggus or ) Area : 172 sqm. 7. General note - The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The bidder/execution agency must conduct the structural analysis for the installation before bidding. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Terracotta/Haryana craft Diorama Part A- Terracotta/Haryana craft wall artwork - Designing, providing and fixing terracotta/Haryana craft artwork in a layered diorama having 4 layers of terracotta/haryana craft/ MDF/ Acrylic/ bendable Acrylic solid surface/ MS/Fabric/glass) with CNC/LASER/uv print at 2-3 layers finished with PU paint/any other on vertical/horizontal/angled surface.The finish should be such that it compliments the aesthetics of the space meeting the thematic intent. The installation quality and finish should conform to the International standards of museums. The artwork is to be installed as per the design on vertical/horizontal/angled surfaces. The framework of the installation is to be made of a 50X50MM M.S. sections structure. The wooden/metal paneling provides backing for terracotta/Haryana craft artwork. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The Terracotta/Haryana craft Artwork shall be used for varying heights up to the height of a maximum of 4000mm for a running length of up to 60000mm. Terracotta/Haryana craft Artwork is to be designed by a special artist familiar with the craft and made by local artisans/craftsmen with prior experience in the craft. Specialized artist/sculpturist on board for the Terracotta/Haryana craft to take necessary prior approvals from museum design consultant before execution. The installation includes all the things required to meet the intent of the artwork. Please refer to the design presentation for further details. The fixing to include wet/dry cladding of terracotta tiles. the rates are included in paneling/base required for fixing of the artwork in the desired design pattern as approved by the museum design consultant. Area : 240 sqm. Part B - Terracotta/Haryana craft Debri - Providing and laying of custom-made terracotta/Haryana craft pieces in the shapes as per design of tentative size 35x35mm, 50x50mm, 75x75mm in the thickness as per required strength and as per approved by the museum design consultants. Area : 90 sqm. Part C - 2D/3D terracotta/ wood/ metal artwork/Haryana craft - Providing and fixing 2d & 3d wall mounted and freestanding elements of varying sizes of elements like the ship, tree, human silhouettes, haryana settlements, british barracks, shrubs, etc. based on concept and design approved by the design consultant, installed as per the approved arrangement with required supports and frames. The approx. length to be 30m and height up to 4m. Material - terracotta/Metal/ Mdf/Corian/MS/corten steel/plywood/frp/fabric with CNC and laser cutting of artwork in approx. 50% of the surface area as per size and design of each element. Finish shall be provided as directed by Museum Design Consultants. Area : 90 sqm. Part D - Brick/terracotta tile floor - Providing , fabrication and laying flooring of custom made brick having artwork with size and laying pattern according the reference or as approved by the museum design consultant. The bricks/tiles should not have chips, cracks, discoloration or other visible defects. Jointing and compunding to be done in lime/ surkhi/ white cement and other colored pigment. Maintain uniform, aligned joints // 10 mm (3/8- inch) // 13 mm (1/2 inch) // wide or as specified by the museum design consultant. Curing to be done if required. The flooring to be complete with the cleaning, sealing and protetion process. Provision for entrance ramp to be also provided for universal access. Area : 210 sqm. Part E- Terracotta/Haryana craft ceiling - Providing and fixing terracotta/Haryana craft ceiling of size and proportion of a custom brick or as per design reference with necessary supports. Inclusive of M.S. T angles/wooden rafters as per structural consultants. The ceiling to be complete with all the necessary hardwares and accessories required for the ceilig suspension and durability. Area : 305 sqm. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The bidder/execution agency must conduct the structural analysis for the installation before bidding.

NS Causes exhibit - This installation intends to inform the museum visitor about the various causes such as shift in revenue system and trading rights, confiscation of property, farming laws, Irregulated judicial system, doctrine of lapse, greased cartridge etc. that lead to the revolution of 1857, through various interactive and dynamic exhibits. The details of the exhibits are as follows : Part A- Farming scenography and kinetic installation - Providing, fixing, and installation of a circular gallery having curved partition walls finished with 2-3 mm thick M.S. sheet/Corten steel on both sides having top coating as per design approval. The partition is to be of 150 mm overall thickness, made of 50x50 M.S. frame structure with a top cover of 12 mm flexible ply, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. 2D/3D elements to create scenography of dried, burnt farm field with burnt/ dried/ rotten crops, with the floor having cracks and burns, heaps of straw kept in the field as per design made jute/ bamboo/ mud/ FRP/M.S./wood/MDF or similar as per design. The passageways are to be made in concentric circles or as per design in levels with mud plaster/micro topping as per the scenography requirements. Provision in the center, for kinetic installation having 5 elements such as bread, documents, crops, farming tools, etc. symbolizing various causes to be made in FRP/M.S./wood/MDF/Corian/acrylic/or any other similar material as per approved by the museum design consultant. Each element is to be moved vertically/horizontally as per the show with a mechanism synchronized with the AV content of the show. The cost to be exclusive of acoustic solutions. Rate is exclusive of kinetic mechanism and inclusive of 5 elements for the installation. Area : 36 sqm. Part B- Greased cartridge hologram installation - Providing and fixing of hologram room/box of size 4500mm x 4000mm with height 4000mm made of partition. The partition to be of 150 mm overall thickness partition made of 50x50mm M.S. frame structure with top cover of 12 mm flexible ply, conforming to BWR grade on both side with provision of infilling of Acoustical insulation within the Frame structure, the wood to be treated with anti-termite solution, formaldehyde free, fire retardant. 12mm thick extra clear toughened glass with 0.4-1mm thick holographic film fixed on the back side of the projection. The Hologram Box will be finished on one side 2-3 mm thick M.S. sheet/Corten steel/micro-topping finish as per specfications and on the inside the hologram box will be finished with primer base and paint/microtopping/vinyl as per approved. The room/box to have 2D/3D elements in FRP/M.S./wood/MDF/Corian/acrylic to create scenography set up of a scene such as dum dum depot or greased cartridge factory/ barrackpore soldier encampment or other such scenography of exterior views of the approved scene by the museum design consultant. Installation complete with all necessary Hardware. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Appropriate accoustic measures to be considered for sound proofing of the installation within the panelling and avoiding any echo/ reverberation of sound. Area : 18 sqm. Part C- The labyrinth with interactions set up - Providing and fixing of metal wall partition varying in height from 750mmnup to ceiling height of 4000mm. The partition to be made of 2-5mm M.S. sheets/corten steel sheets/Copper sheet joined with each other with appropriate metal jointing technique as per approved by the museum design consultants. The partitions to be finished in top coat such as paint/duco/lacqured/oil finish as per approval. The sheets to be complete with CNC/laser cutting of Artwork on 50% area of the panelling having niches/cut-out/peepholes to accomodate holograms and artefacts as per design .Item should include jointing and finishing of the corten steel/M.S./Copper sheet to a flush finish with recommended framework/dry cladding system / clamping system all complete. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Appropriate accoustic measures to be considered for sound proofing of the installation within the panelling and avoiding any echo/ reverberation of sound. The shop drawings to be vetted by the structural consultant and as per the satisfaction of engineer in charge. Provision for doors/partition opening mechanism with customised hinges & locking mechanism wherever required as per approved detail drawings. Area : 148 sqm. Extra clear glass - Providing and fixing 12mm toughened glass extra clear of custom size as per the site conditions to be fixed with studs and channels/ any other provision as per the design. Inclusive of all - fixtures, fittings, hardware, hanging system, 3M adhesives, extra clear transparent silicon, or any other mechanism required to make it functional. Area : 64 sqm. Interaction button table (3500x600mm) - Providing and fixing of table of size - 3.5m x .6m x 0.9m made in 50X50mm Square pipe(if needed 50mm diameter pipe can be used) c/c 450mm frame with 12mm commercial ply on top and finished with 12mm thick Corian as per design, with provision of cove at the bottom. Provisions for corian buttons to be provided over the mehcanical buttons. Rate to exclude LED light fixture in cove with drivers and wiring. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Provision for openable shutter, concealed lockable system as per requirement of the installation for its maintenance and operation to be also provided. Inclusive of CNC/laser cutting for making slotting/ louvers/ perforations for operations and maintanence. Qty. : 1nos. Corian table (1500x450mm) - Providing and Fixing of table of size 1.5 x .45mm with height .90 mm with base made of 50X50mm hollow sections of desired thickness with appropriate spacing and necessary welding at junctions including applying of required coats of steel primer on sections. The cost is inclusive of providing and fixing 12mm thk commercial ply of approved make on MS frame work with necessary hardwares,screws etc all complete. The top to be finished in 12 mm thk corian of approved make and shade fixed to the ply with silicone adhesives including buffing and polishing of the surface as per approved drawings. The corian top will be etched with artwork. The remaining area to be painted in duco of approved shade. Under special conditions, the size of the table may vary and cost considered to be under prorata basis proportionately. Area : 3 sqm. 2d/3d artwork - Providing and fixing of 2D/3D artwork of desired size in design as per the concept approved by the museum design consultant. The brass to be used in sheets/ poured into moulds/ inlays to make the artworks as per graphic detail approved by the museum design consultant. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. Please refer to the design presentation for further details. Area : 40 sqm. Brass artwork - Providing and fixing of 2D/3D artwork of sizes 300x300mm, 600x600mm 1200x1200mm in design as per the concept approved by the museum design consultant. The brass to be used in sheets/ poured into moulds/ inlays to make the artworks as per graphic detail approved by the museum design consultant. Area : 10 sqm. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The bidder/execution agency must conduct the structural analysis for the installation before bidding. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Planning scenography - Special installation with set design recreating forest scenography through various elements such as trees, mud flooring, dense ceiling, infiltrating light through trees, having natural finishes such as mud plaster, sarkanda/bamboo paneling backdrop, etc. The installation intends to create a secretive, surprising, and engaging mood such that the museum visitor may experience becoming a part of the planning of a revolution explaining the various aspects concerning the planning of the 1857 free struggle. Inclusive of but not limited to the following: Part A- Trees - Providing and installing realistic trees having details like peeled bark, bark texture,war markings etc. in FRP/MDF/metal with atleast 20 openable panels as per design in which the elements delivers secret messages to the visitors. The height of the tree to be 3500mm-4500mm (variable as per design requirements). The tree radius to be varying from 450-900mm. The number of trees approx. 60-70 nos. The finish of the tree high quality duco/pu paint/acrylic paint/ as per approved by the museum design consultant. Provision for openable shutter, concealed hinges, magnetic lockable system with provision for placing touch pad/ tablets or any other artefacts as per design. The rate to be inclusive of base plate required for fixing the tree durably with the floor. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Tree (without openable panels) - 40 Nos. Trees replicas with openable panels with provision of tablet fixing inside the openable panel. -15 Nos. Part B- Sculptures - Designing, fabricating, installation and finishing models/sculpture as per scenography requirements including props in approx. diameter 1800-3000mm and height up to 4m having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 5nos. Part C- Documentary seating - Providing and arranging rustic wooden log seating of size 450mm-600mm diameter of natural wood seasoned well to be used as a piece of furniture. Qty. : 25nos. Part D- Backdrop - Providing and fixing of panelling in Sarkanda/ jute/bamboo in the pattern as suggested by the sarkanda/jute craftsmen and that matches the design intent. The sarkanda/jute panelling to be done by the special artists/ expert craftsmen of Haryana and approved by museum design consultant. The panelling finish should be good for projection. The panelling to be fixed with base using nails, adhesives, and all necessary accessories required to make it functional. The rate is exclusive of cost for projection paint wherever required. Area : 128 sqm. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS 1. Active studio grade wall mount speaker Driver Size: 3" Bass + 3/4" Treble (metal dome) Amplifier Power :25W Bass + 25W Treble(Class D) Maximum SPL : Peak - 96dB Frequency Response (-6 dB) : 67 Hz - 25 kHz Distortion: < 0.08% Active crossover operating at low signal levels. Precise room response compensation for optimizing in-room performance. Directivity Control Waveguidefor flat on- and off-axis response. Intelligent Signal Sensing for power consumption reduction in stand-by mode. Minimum Diffraction Enclosure for uncoloured sound reproduction. Each transducer is driven by its own optimized amplifier. Installation: Versatile mounting options for all installation needs. Connections: 1 x XLR Analog Input Enclosure material: Die cast aluminium. Qty.: 12 nos. Make-Genlec / Devialet / Tannoy / Adam audio/ AKG 2. 4x4 USB 2.0 Audio/MIDI Interface- 24-Bit/192 kHz resolution for professional audio quality, Compatible with popular recording software including Avid Pro Tools*, Ableton Live*, Steinberg Cubase*, etc. Streams 4 inputs / 4 outputs plus 1x MIDI I/O. Input/Playback Mix control and Stereo/Mono switch for direct monitoring. Status, Signal and Clip indications for perfect overview. Main Outputs on balanced XLR and 1/4" TRS connectors. Qty.: 6 nos. Make-Behringer / Presonus / Steinberg / Focusrite 3. Professional Studio grade Closed-back dynamic over ear headphone Driver Diameter - 40 mm or better Frequency Response: 15 - 20,000 Hz Maximum Input Power: 700 mW at 1 kHz Sensitivity: 96 dB or better Impedance: 47 ohms Cable: 3.0 m (9.8'), straight, left-side exit Magnet: Neodymium Voice Coil: Copper-clad aluminum wire Folding/collapsible: Yes Accessories Included: 6.3 mm (1/4") snap-on adapter. Qty.: 3 nos. Make-Audio Technica / Bose / Focal / Beyerdynamic/ AKG 4. Headphone Aamplfier - 4 channel stero headphoen amplifier with maximum input level of upto +15dBU, 1/4" TRS connector, stereo input and output connectors. Qty.: 2 nos. Make-Behringer / Presonus / Art / Focusrite 5. Directional Audio Spot speakers to cover the Bowl perimter for open listening in fixed space. Qty.: 2 nos. Make-Holosonics / Panphonics / Ultrasonic Audio 6. 20/22 AWG Microphone/Signal Cable ( as per actual) Qty.: 675 m Make-Belden / Canare / Sommer / Proel 7. Various Audio Connectors to complete the system. Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. 8" Ceiling speaker with very tight coverge pattern Driver Size : 1 x 8” driver with dual concentric or co-axial design/1 x 8" driver Sensitivity : 93dB/92 dB RMS Power : 90 W or better In-built transformer Tap : 100V / 70V upto 60W Maximum SPL : RMS - 113dB , Peak - 119dB/118dB Peak Dispersion: 60 Degree Conical or lesser Frequency Range (-10 dB) : 40 Hz - 20 kHz/58 Hz – 20 kHz Certification: UL 94V-0, UL-1480, UL-2043, CE Enclosure : Zinc plated steel Steel, with weather resistant coating grill Included Accessories: C-Ring, tile-bridge kit, paint mask, cut-out template, grille Qty.: 5 nos. Make-Tannoy / Focal / Martin Logan / Defintive Technology / Bose/ JBL 2. 4 Channel Class D 1000 watts Power amplifier/ 4-channel Class D 1200Watt Network amplifier with DSP THD 20Hz-20kHz at 1 W <0.1% Signal To Noise Ratio >106 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 250 W @ 2 Ohms / 4Ohms / 8 ohms / 16 ohms -4 x 300W @ 2/4/8 Ohms 70V / 100 V Compatible Max. output current 14 Arms Frequency Response : 10 Hz - 20 kHz Input impedance 20 kOhm Common Mode Rejection (CMR) 50 dB Output impedance 25 mOhm Enerygy Star Rated Cooling : Single fan, front to rear airflow, temperature controlled speed Comprehensive circuit protection and fault indication Qty.: 1 nos. Make-Labgruppen / Powersoft / AtlasIED / LEA Professional/ Crown-Harman 3. 4x4 USB 2.0 Audio/MIDI Interface- 24-Bit/192 kHz resolution for professional audio quality, Compatible with popular recording software including Avid Pro Tools*, Ableton Live*, Steinberg Cubase*, etc. Streams 4 inputs / 4 outputs plus 1x MIDI I/O. Input/Playback Mix control and Stereo/Mono switch for direct monitoring. Status, Signal and Clip indications for perfect overview. Main Outputs on balanced XLR and 1/4" TRS connectors. Qty.: 1 nos. Make-Behringer / Presonus / Steinberg / Focusrite 4. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 360m Make-Belden / Canare / Sommer / Proel 5. Various Audio Connectors to complete the system Qty.: 1 lot Make-Neutrik / Switchkraft / Amphenol The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS 1. Supply installation testing and commissioning of two way wall mount speaker Built-in 70V & 100V transformer 8"+2" Economy range speaker of excellent sound quality Power taps 5W/10W/20W/40W/80W @100V outout Both 100V and 80hm outputs Fashion speaker of black color Make-Harman(JBL). Qty.: 10 nos. EXISTING* Make-JBL - Control28 (model to be confiremd by Customer) 2. Supply, Installation,Testing & Commissioning of Ceilingspeaker 2-way built-in loudspeaker,Power rated-40W/20W/15W/8ohm, “the reference loudspeaker”. It can be used with a standard Hifi amplifier and provides you with a Pro HiFi sound. The loudspeaker has an enforced 6 ½” woofer and 1” tweeter.suitable for the distribution of Back Ground Music.The housing is made of high quality ABS.SPL 1 watt/1 m-92db,SPL Max peak-106db,Frequency Range-60Hz to 20Hz Dispersion @ 1 kH-180Deg,@4KHz-80Deg,@8KHz-45Deg,IP-54 Rated Make-Harman(JBL). Qty.: 10 nos. EXISTING* Make-JBL - (model to be confiremd by Customer) 3. Dual Channel Class D DANTE 480Watts Power amplifier/Dual Channel Class D DANTE 600Watts Power amplifier Distortion, 1/8 rated power <0.1% Signal To Noise Ratio: >101 dBA Channel separation (Crosstalk) >72 dBA Power Handling : 2 x 240W @ 4/8ohm & 70V/100V/ - 2x300W @ 4/8ohm & 70V/100V Dante 2 channel Rx Input Transmission High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz GPI remote volume control using standard RJ-45 connector and Ethernet cable Energy Star Rated/optional Amplifier protection Thermal protection, over current protection, DC protection, high frequency protection Cooling Convection-cooled, fanless. Qty.: 2 nos. Make-labgruppen / Powersoft / AtlasIED / LEA Professional / Bose/ Crown- Harman 4. 2.5 Sq mm Speaker Cable (as per actual) Qty.: 360 m Make-Belden / Canare / Sommer / Proel The quality, mechanism and finish of the work should conform to the International standards of museums. The installation is inclusive of all the neccessary audio equipmets, softwares, applications, accessories, special effects or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation to provide appropriate audio solution for the same. All the items required to meet the desired audio output of the installation shall be under the scope of the bidder/execution agency. The necessary approvals to be taken from the museum design consultant and engineer-in- charge before execution of works. *These items have been procured already. Cost of installation, integration , testing and commisioning to be considered for these.

NS Celebrating Haryana Crafts installation - This artwork will appreciate and spread awareness about the lost and rare crafts of Haryana region. Visitors will understand the materials, textures, techniques through the installations. These crafts will be designed, fabricated and installed in their original forms by the special and celebrated artists. The details of the installation is as follows: Designing, providing and fixing of artwork installation made by special artist demonstrating the rich Haryana crafts such as Hand embroidery, Punja durries making, Terracotta craft, Metal jewellery, Mudah making, Brass Metal, zari jutti, Sandalwood carving, Sanjhi craft, Basketry, Crochet, Wooden beads, Pot painting, Lac bangles, Wood craft, Leather work,etc. of various regions of Haryana such as Gurgaon, Rewari, Jhajjar, Faridabad, Sonepat, Panipat, Karnal, Ambala, Bhiwani, Chandigarh, Kurukshetra, Hissar, Sirsa, Mahendragarh, Yamuna Nagar, Rohtak, Jind,Kaithal, Panchkula and many others. The artwork is to be installed as per the design on vertical/horizontal/angled surfaces. The tentative size of the artwork installation is 1200x1200mm, 1200x2400mm, 3000x3000mm depending on the site conditions and the design proposal by the artist and as per design approvals. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The artwork needs to be fixed on base framework of varied basework as per the respective artwork and approved detail/design. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Rates are excluding the panelling cost but including the installation and other allied items. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Kinetic map table - Providing and fixing Kinetic Sculpture table of approx. dia. of 5000mm made with custom made extruded, engraved with CNC milling/etching rubberwood/pine wood /mdf/moulded FRP/ acrylic solid surface/ blocks of size maximum of 100mm X100mm X 100mm which will have movement of the blocks with motorized mechanism based on servo motors(silent type) , mounted on the wooden base as per design filled with acoustical material , made of 100X50mm or as per requirements timber/metal section frame 600mm c/c with 12mm thick commercial ply on top , finished with primer base and Vinyl/acrylic bent surface on outer phase of the wooden ply. Base to be made as per specifications by the museum design consultant, following partition thickness of 150-300mm. all wooden sections will be seasoned and coated with any termite coating with all necessary hardware and colour approved by museum design consultants. The kinetic sculpture design and shop drawing to be made as per the reference given and approval by museum design consultant. Provision for openable shutter, concealed lockable system, ventilation fans as per requirement of the installation for its maintenance and operation to be also provided. Inclusive of CNC/laser cutting for making slotting/ louvers/ perforations for operations and maintanence. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional as per the design. General note - The installation quality, mechanism and finish of the installation should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Events at Ambala- Show - This show is to inform the museum visitor about the series of events of incendiary fires at many places in Ambala cantonment as a part of pre-revolt events by recreating the scene of fire through digital mediums on various building models such as European Armory Buildings, British official's houses, British barracks in Ambala cantonments, Hospitals, etc. This curated show is the amalgamation of physical elements and technologies such as A.V., synchronized lighting, fog machines, scent diffusers, etc. The main components of the show are listed below: Site models -Display: Ambala monumnets and buildings - Open fire installation depicting the scenography with the scaled models upto 15 nos. of varying sizes such as 1mx1m, 2mx2m,3mx3m, 6mx4m, depicting various buildings/scenes such as the St Paul's Church in Ambala, cantonment areas, hospitals,landmark/residence buildings of the war and other historically relevant buildings as per design.The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/MDF/Corian/acrylic/concrete/ mud/brick/ metal/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties as per design reference. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 210 sqm. Acrylic Solid surface bench - Providing and fixing of backless curved/straight bench in 12 mm bendable Acrylic solid surface finish of approved shade and make of size - 1500x450x450mm, with provision of cove at the bottom as per the approved detail drawings . The bendable acrylic solid surface should be be backed with appropriate MS structure 50X50 mm hollow sections of desired thickness with necessary welding at junctions. The cost is inclusive of proving and fixing 12mm thk flexible/ 18 mm thick commercial board of approved make with necessary hardware, screws etc all complete as per the direction of engineer in charge. The cost should also be inclusive of all necessary adhesives, grinding, buffing etc for installation of bendable acrylic solid surface on the base. Under special conditions, the size of the table may vary and cost considered to be under prorata basis proportionately. Sample bench to be approved by Museum Design Consultant. The bench should also have a 2D/3D graphic as a museum branding or as per the design language of the space. Rate to exclude LED light fixture in cove with drivers and wiring. Qty. : 10 nos. General note - The installation quality, mechanism and finish of the installation should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Telegraph Installation: - Scenography receation of telegraphs offices with partially interiors of a telegraph office and partially exterior of telegraph lines on poles in open grounds. The set to be complete with all the elements required to achieve the required aesthetics. The main components of the installation are follows: Interior set up - Providing, fixing and setting of interior scene of a telegraph office for a room size 12m x 8m with all the components of Telegraph office in 1850's in India. The walls to be of exposed brick work with the approved brick bond with lime plaster finish where required having various elements such as wooden windows, door 2.0m x 2.5m, fireplace, hardwood flooring, hardwood ceiling with wooden rafters as per the picture references from old lithographs and paintings of 1850's. The installation to include the teak wood/real wood furniture - 2 nos. table of size 2.0mx.75m., chairs- 4nos. 0.5m x 0.5m, 1 nos. table of size 3.0m x 1.5m finished in polish as per design. Provision for openable shutter as per requirement of the installation for its maintenance and operation to be also provided.The installation to include all the loose objects real/conserved/replica made of wood/metal/frp required for the scenography such as window frames, photo frames, table decorations, mantle pieces, chests,transmitters, telegraph machines, mannequins, decorative lights etc., of design as approved by the Museum Design Consultant. Finishes wherever required should be good for projections. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The details of the elements are as follows: False Flooring - 150mm - Providing and Fixing of False floor with MS tubular section of 50mmX50mm/75mmX75mm/as per requirement of desired thickness with appropriate spacing and necessary welding at junctions including application of double board of 25mm to 32mm thick BWR grade plywood/ commercial board of Greenply/Century ply or eqv fixed to base with 2mm thk MS plate of desired size and base properly welded with all fasteners and necessary hardware's with edge profiles, beadings etc all complete as per approved design. The rate is also inclusive of two coats of MS primer on the frame structure and one to two coats of anti termite oil finish on ply board. Height of False flooring to be considered is 150mm alongwith provision of cove as per design requirement. Wooden Flooring - Providing and fixing of interlocking timber planks in at least 25 mm in thickness as per traditional design pattern approved by the museum design consultants. The wood to be seasoned well and defect free. The top finish to be paint/polish/oil as per approved by the Museum Design Consultant. The rate is also inclusive of one to two coats of anti termite oil finish on wooden surface. The edge of the flooring to have the provision for cove lights. Excluding the cost of LED light fixture. Mud flooring - Providing and laying of 10mm - 12mm Thk. Mud plaster with appropriate proportion of cememnt mixed with local mud and chopped and sifted straw laid in a single unjointed layer rammed thoroughly upto a desired thickness. The finish layer applied to be a mixture of cow dung and clay with a thickness of min 1mm on with rapid curing on existing false floor similar to ground surface of archelogical excavation sites found in haryana, with MS wire mesh gauge as per area demarked on drawing , as per approval by museum design consultant. Wooden Ceiling - Providing and fixing of the wooden ceiling at the height as specified in the drawings having wooden rafter of upto 150x300mm with wooden planks as ceiling covers. The wood shall be well seasoned and defect free. The ceiling to be finished in paint/polish/oil as approved by the museum design consultants. The cost to be inclusive of applying one or two coats of antitermite solution. The cost to also include all necessary hardwares, fixtures, hanging mechanism to hang the wooden planks with stability all complete as per the satisfaction of engineer in charge. Recreated telegraph office walls - Providing and fixing of wall made of exposed customised brick of size of a lakhori brick. The panelling to have various elements such as the fireplace, decorative lintels and sills, niches, brick columns, wooden lintel beams etc. as per the design approved by the Museum Design Consultant. The cost to be inclusive of jointing and compounding with lime/surkhi/white cement and colour adhesive pigment. The wall to have all necessary stuctures, support, MS to provide stability as per the satisfaction of engineer in charge. Conserved / replica wooden decorative elements - Providing and fixing up to 7 nos. conserved antique seasoned wood used to make replicas of wooden elements such as window frames, table decorations, mantle pieces, chests etc of design as approved by the Museum Design Consultant. The cost to be inclusive of applying one or two coats of antitermite solution. finish having antique look, antique hardware & fittings required to make it functional. Conserved wooden pattern door - Providing and fixing conserved/replicas of wooden doors of design as approved by the Museum Design Consultant. The door to be complete with frame and fittings. Door size: 2000x2500mm. The rate is also inclusive of one to two coats of anti termite oil finish on wooden surface. - Exterior set up - Providing, fixing and setting up of an exterior ground where the telegraphs lines used to run on poles in room size of 14m x 8m having elements like real/replicas of telegraph poles with telegraph wires having suspended wires connecting poles with anchoring techniques as used in 1800's. The elements such as mud floors , teakwood/real wood furniture such as tables 4nos. of size 1.2m x .9m and chairs 8 nos. of size 0.5m x 0.5m as per design. Provision for openable shutter as per requirement of the installation for its maintenance and operation to be also provided. Walls to be of backlit printed stretched facric and ceiling in non printed backlit stretched fabric as per approved by the museum design consultant. (The cost to exclude the lighting). The details of the elements are as follows: Stretch Ceiling- Non Printed - Supply and installation of demountable PVC Stretch Ceiling welding with harpoon ready to install. (Fire Rated to European Standards b-s1-d0/b-s2-d0/B1/b2*) With 5 years warranty on stretch membrane seam ruptures & profile. All joints to be fused / provided with approximate interface trims to be able to demount the stretch ceiling to access the lights. The stretch ceiling shall be installed as per details drawing using proprietary aluminium profile complete as per manufacturer's installation guidelines and as per approved shop drawings in line with the design intent and approval by the museum design consultant (Make - Barisol/ Euroceil or equivalent ). Providing 5 year manufacture warranty, adhering to manufacture installation guidelines and achieving maximum light. (Lighting fixtures cost not to be included). Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Rate inclusive of framework required with customised profile for installing stretch ceiling.the frame should include housing for the lighithing system to be installed. Adequate opening provisions for operation and maintanence of the panel to be considered. Stretch Fabric paneling - printed - Supply and installation of demountable PVC Stretch wall paneling welding with harpoon ready to install. (Fire Rated to European Standards b-s1-d0/b-s2-d0/B1/b2*) With 5 years warranty on stretch membrane seam ruptures & profile. All joints to be fused / provided with approximate interface trims to be able to demount the stretch ceiling to access the lights. The stretch ceiling shall be installed as per details drawing using proprietary aluminium profile complete as per manufacturer's installation guidelines and as per approved shop drawings in line with the design intent and approval by the museum design consultant (Make - Barisol/ Euroceil or equivalent ). Providing 5 year manufacture warranty, adhering to manufacture installation guidelines and achieving maximum light. (Lighting fixtures cost not to be included). Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Rate inclusive of framework required with customised profile for installing stretch ceiling.the frame should include housing for the lighithing sysytem to be installed. Adequate opening provisions for operation and maintanence of the panel to be considered. The print quality to be UV print quality, non- fadable and durable. Telehraph machines/ equipments - Providing and fixing conserved/replicas of wooden/metal/frp elements such as transmeitters, telegraph machine etc of design as approved by the Museum Design Consultant. Telegraph poles - Providing and fixing of wooden photo frames with 50X50 or 75X75MM wooden border finished with Paint/Oil texture, with hangable fixture over the wall. The frame of customizble size up to 2M by 2M of max size also having a glass fixed in the frame to past vinyl or print a graphic over the same. The frame should be sampled and get approved by the museum design consultant. he rate is also inclusive of one to two coats of anti termite oil finish on wooden surface. The rate is also inclusive of one to two coats of anti termite oil finish on wooden surface. Wooden Photo Frame - Providing and fixing of wooden photo frames with 50X50 or 75X75MM wooden border finsed with Paint/Oil texture, with hangable fixture over the wall. The frame of customizble size up to 2M by 2M of max size also having a glass fixed in the frame to past vinyl or print a graphic over the same. The frame should be sampled and get approved by the museum design consultant. he rate is also inclusive of one to two coats of anti termite oil finish on wooden surface. The rate is also inclusive of one to two coats of anti termite oil finish on wooden surface. Telegraph table -1 - Wooden table size: 2500x900mm. Design as approved by the Museum Design Consultant. The rate is also inclusive of one to two coats of anti termite oil finish on wooden surface. Telegraph table -2 - Wooden table with top good for projection. Size: 3000x1500mm.Design as approved by the Museum Design Consultant. The rate is also inclusive of one to two coats of anti termite oil finish on wooden surface. Telegraph intereaction table - Wooden table size: 1500x900mm. Design as approved by the Museum Design Consultant. Wooden chairs - Wooden chairs of size : 450x450x750mm. Design as approved by the Museum Design Consultant. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Haryana Map Installation - This installation intends to highlight the importance of the revolt centres in haryana, highlighting various routes, road connectivity as well as the geographical fabric of Haryana. The installation will have 2d/3d maps along floor, walls, and ceiling. The main components of the installation are as follows: Map model and shell - Providing, fabricating, detail deisgning and fixing of 3d Haryana map model 3D printed/digitally fabricated as per design approval in plastic/MDF/Rubberised Cork/acrylic solid surface spanning across floor, walls and ceiling the room of size of 21000mmX14000mm. The height of the model to vary from 12mm-450mm as per design. The model to be finished in duco paint/projection paint/ microtopping or as per design approval. The structural curvable of the shell to be made in 75-150mm thick partition having M.S./wooden battens framework with 12-18mm thick flexible ply, finished on top with etched MDF/acrylic solid surface/duco paint/vinyl graphics/UV printing as per design. To attain the desired shell shape materials such as foam, sunboard, pop, GI mesh, glasswool to be included. The hollow space to be filled with glasswool to achieve the desired acoustics levels.To ensure the smoothness of the curvature structural 3d visualization and 2d drawings to be made. The map to be etched/embossed on the shell surface as per required. The structural stability of the shell and the model to be checked by a structural engineer. Provision for programmable lighting within the model. All necessary provisions for projector, lighting, speaker mounting to be provided. All Mild steel will be coated with anti-rust coating / paint. Provision for openable shutter as per requirement of the installation for its maintenance and operation to be also provided. images provided by museum interior consultant. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional as per the design. Relevant Data expert to be brought on board as required for achieving authenticity of the model. Specialized artist/sculpturist on board for the installations to take necessary prior approvals from museum design consultant before execution. (the cost of lighting to be excluded) Area : 275 sqm. Battle Models with base - Designing, fabricating, installation and finishing models/sculpture as per scenography requirements including props in approx. on site of 3D printed/wooden/metal models of avg. size - 0.15m x 0.15m x 0.15m - .45mx.45mx.45m having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as / FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. Each model shall have NFC/ RFID tag on it, which when interacting with the sensor screen will display information on the tablets. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 15nos. - Part 2 : Providing and fixing of M.S. stands with a plate shaped as per design of varying sizes from .15m x .15m to .60x .60m standing on a pole of approved thickness of height upto 1.2m. The pole to be finished in PU/duco finish of approved shade by the museum design consultant. The assembly should be structurally stable with neat joinery as per approved by the museum design consultant. Qty. : 15nos. Connecting bridges - Metal ramps- Providing and fixing of M.S./aluminium sheet ramp floor made of 50x50mm/ 75x75mm/ 100x100mm of core size min 4mm MS structure duly fixed on floor with 300x300x10mm plate fastened on the laid PCC.The top cover of the structure M.S. sheet 4mm thick anti slip dully welded with the structure. The height of the bridge to vary from ground level to 1200mm . The structure to be vetted by structural consultant keeping in mind the live load required. All Mild steel will be coated with steel primer, anti-rust coating, duco paint and all complete with all necessary hardware, equipment's and colour approved by museum Consultants. Ramp tentative size - 1200x 80000mm. Area : 96 sqm. - Glass ramp- Providing and fixing of glass ramp made of 15mm thick extra clear factory laminated glass double layered with 3m protection film, scratch free, extra clear film of thickness up to 0.4-2mm. The glass to be of customized sizes as per the curvature of the floor. The cost to include the ply for the mould/shape used to attain the desired shape. The ramp width to be up to 1500mm and raised height upto 1200mm from ground level. The framework in M.S./aluminium sheet ramp floor made of 50x50mm/ 75x75mm/ 100x100mm of core size min 4mm MS structure dully fixed on floor with 300x300x10mm plate fastened on the laid PCC. The structure to be vetted by structural consultant keeping in mind the live load required. All Mild steel will be coated with steel primer, anti-rust coating, duco paint and all complete with all necessary hardware, equipment's and colour approved by museum Consultants. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Appropriate accoustic measures to be considered for sound proofing of the installation within the panelling and avoiding any echo/ reverberation of sound. Tentative length of the ramp : 16m. Area : 19.2 sqm. - Railings: Providing and fixing M.S. railing of varying height from 450mm to 900mm high, using 50X50mm/75x75mm of 2-4mm thick core M.S. section duly welded with the M.S. floor structure. M.S. to be paited with steel primer and finished in approved duco paint. The railing will have 10-12mm thick toughnened glass sandwiched in Hollow tube sections /channels with all necessary fittings, nut bolting, welding, grinding, silicon etc. to make it stable. The glass to have the edge with machine polished and bevelled as per design. At intervals as per design, provision for tablets to be made up to 4mm thick M.S sheets of width up to 450mm curved and bended in factory finish with corners and edges cut in CNC/laser with smooth finish. The stand to have provision for holding the tablets to be used by the visitors. Provision for electrical wiring and cabling to be considered via metal conduits through the hollow tubular sections. Tentative length : 106m. Area : 96 sqm. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Katputli Show - This gallery has mechanical and automated katputli movement show of duration of 8-10 minutes of occurrences of battles in different regions of Haryana and the tough fight between the different people of Haryana and the British army. The entire show will highlight the major events of the Freedom Struggle in the region. Using the media of the Katputli folk culture i.e. the puppetry show which is different puppets handled by few strings for movement. The following are the details of the gallery: Puppet Show installation (stage and gallery ceiling) - Detail designing, providing, fabricating and installating theatrical experience designed by special artist with world class mechanism using the puppet craft of Haryana. The installation is designed mechanically withnew technologies and machineris for traditional puppet show showcasing the various events of 1857 war in Haryana. The stage setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall with provision for all cabling wiring or any other mechanism required for movement of the puppets in the desired synchronized manner. The top cover of the frame is made up of handcrafted cloth/artwork/acoustical foam, cloth/as per design. the length of the stage is upto 15m and height upto 3m. The back wall will have leveled layered creating a 3d niche/space for the show. Remaining surface are on the walls will have 2-3 layered diorama depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the diorama. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardwares, screws etc all complete as per direction of engineer in charge. The ply to be leved in a way that it is durable fo rficxing carpet with adhesives along with all the edge detailing and profiles.The puppets to be of varyinng size from 400 -1500mm, made of wood carving, fabric, metal wire, frp, attached with strings and other suitable mechanism/motors synced with the controller as per the design to show different movements along with other props and scenography elements as per approved by musuem design consultants. Proper operation and mechanism to be considered while designing the mechanical show. Provision for integration of the mechanical movements along with projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. The customized programming of the puppet show needs to be synced for moveable/rotateable parts along with the audio visuals. The cost of puppets, along with the attire, props/elements/artefacts as required as per the design and theme to be consdered. There will be a motorised curtain operated with the remote for beginning and climax of the show to be controlled at the server station. The remaining area will be covered with wall panelling, ceiling and flooring with carpet/upholstery as per design and theme. All the provisions required for hangi ng of any props projectors, equipments, canvasing any equipments to be considered. The gallery to have the finish in designed fabric to be suspended from the structural ceiling to complete the set up as per design approval. Qty. : 1nos. Amphitheatrical steps - Providing and fixing of amphithatrical stepped seating made up of M.S. angle in tube/ISMB dully welded with the base plate of desired size and thickness duly fixed with necessary fixtures, fasteners/nut bolts etc all complete with the existing base. The structure to be vetted by structural consultant keeping in mind the live load required. covered in the fabric/rug designed by a special artist of punja dari artwork of Haryana as per approved having 7-8 seating platforms of high risers of 300mm with intermediate climbing steps. The structure of the stepped auditorium seats to be in M.S./ wooden section of size as per structural requirements. The railing to be provided as per as per design. The seating to be 12m wide and 16m in length. The steps to be covered in carpet made of weaving craft of punja dari by the special artist/craftsmen in the approved pattern and shade. The carpet to be anti skid, excellent sound insulation,easy to maintain with self levelling compound of desired colour, applied as per the area demarcated in the drawing. The carpet to cover the amphitheatrical seating and the mezzanine floor.The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Qty. : 1nos. Punja-Dari Paneling - Providing and fixing of Wall paneling of thick fabric woven in the weaving craft of 'punja dari' making of Haryana by the special artist/craftsmen in the approved pattern and shade. The base of the paneling to be of 50-75 mm overall thickness free standing partition up to 4 meter height consisting of ms hollow section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm flexible ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The bending of the ms frames to be made in factory finish as per desired design. The base work to be complete with the required cushioning for the fabric panelling. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. Provision for acoustics to be considered as per sound engineer. The structural to be vetted by structural consultant and submitted to engineer-in-charge. Area : 190 sqm. Punja-Dari carpet - Providing and laying carpet made of weaving craft of punja dari by the special artist/craftsmen in the approved pattern and shade. The carpet to be anti skid, excellent sound insulation,easy to maintain with self levelling compound of desired colour, applied as per the area demarcated in the drawing. The carpet to cover the amphitheatrical seating and the mezzanine floor.The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Area : 146 sqm. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS 1. War at Haryana installation - The multimedia exhibition interactions showcase the battle scenes across Haryana in in details in the major cities i.e. Thanesar, Rohnat, Mewat, Gurgaon, Hisar etc. The overall space includes multiple projections show the details of the places/people/villages/areas etc where the battles occurred and were fought between the freedom fighters and the British. 2. Haryana well recreation - Designing, fabricating, installation and finishing on site of a haryana well scene recreated with real materials such as brick/lime plaster/mud platser/stone/cement plaster/frp/terracotta/thatched roof. The dia of the well is 3m which is surrounded with 4 ornamented columns of dia. Upto .75m. The columns are deisgned in a way having the dome type top with chajjas made in red sandstone and Ms angles, jharokas at various intervals as per design. The well is a replica of the traditional haryana well with all the architectural features such arches, cornices, abutments etc. to match the original. The height of the well to be upto 900mm, the column height upto 4.5m. The aesthetic of the well to match the intent of the design i.e. to replicate the original well of haryana. The finish to be maintained inside the well pit. The work to be done by highly skilled craftsmens who specialise in conservation works and having knowledge of using material like gur, bel-paani, straws, hays in right proportions to attain the desired strength. The well to be incorporated with replicas of traditional pulley made in seasoned wood/stone with all necessary metal supprts along with ropes for fetching water with buckets for atleast 10 people to interact at a time. The well to have necessary provisions for intergrating AV system for the hologram/ projection show.The required surface of the well to be good for projection, inclusive of projection paint. The flooring in and around the well to match the original brick pattern. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. The structural to be vetted by structural consultant and submitted to engineer-in-charge. Any other paint/top coating required to match the aesthics of the well to be included. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional as per the design. Qty. : 1nos. 3. Part A- Haryana village houses - Designing, fabricating, installation and finishing on site of a village scene recreation having Haryana Village with multiple houses of variable size 1m x 1m, 2m x 2m, 3m x 3m with indoor/ outdoor elements of a typical haryana household. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/MDF/Corian/acrylic/concrete/ mud/brick/ metal/terracotta natural material building materials such as thatch roof or other material with highly precise aesthetic properties. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 1nos. 4. Part B- Indian Villager- male, female - Designing, fabricating, installation and finishing models of Indian Village person (male, female) of various regions of India of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props in having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 4 nos. 5. Part C- Indian horse - Designing, fabricating, installation and finishing models of Indian Horse in1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props to be recreated as per design reference having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 1nos. 6. Part D- Indian cattle/ farm animals - Designing, fabricating, installation and finishing model of Indian cattle/ farm animals such as sheep, goat, cow etc. in1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props to be recreated as per design reference having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 2nos. 7. Part E- Utilitarian objects replicas - Designing, fabricating, installation and finishing of replicas of daily objects such as utencils, small storages, chests, candle stands, earthen pots, sack of grains etc. in FRP/wood/metal as per design. The replica to be of size upto 600x600mm or as per scenography requirements. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. The finish to be as per required. Qty. : 10nos. 8. British Army officers model - Designing, fabricating, installation and finishing 3d model sculpture of British Army officer of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 5nos. 9. British Army Men with props model - Designing, fabricating, installation and finishing 3d model of British Army officer of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props and mount such as Horse/ Elephant/ cart to be recreated as per design reference having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 3nos. 10. Indian soldier on foot model - Designing, fabricating, installation and finishing 3d model of Indian infantry soldier of Colonial India of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 10nos. 11. Indian soldier on horse model - Designing, fabricating, installation and finishing models of Indian infantry soldier of Colonial India of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props and mount such as Horse/ cart to be recreated as per design reference having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 5nos. 12. Indian horse - Designing, fabricating, installation and finishing models of Indian Horse in1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props to be recreated as per design reference having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 2 nos. 13. Indian Leader- Male - Designing, fabricating, installation and finishing models of Indian male leader of 1857 rebellion in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 1nos. 14. Indian Leader- Female - Designing, fabricating, installation and finishing model of Indian female leader of 1857 rebellion in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 1nos. 15. Cannon replica - Designing, fabricating, installation and finishing of replica of a cannon of size approximately 2M x 1M or as per design. The cannon to be a part of a projection show hence the surface finish to be good for projection. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. The cannon having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 2nos. 16. Treasury Chest replica 600mm x 400mm - Designing, fabricating, installation and finishing of replica of treasure chest in 1800's of size approximately .60M x .40M in FRP/wood/metal as per design. The chest is to be a filled treasury box with Indian treasure of that time. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 10 nos. 17. Treasury Chest replica 1200mm x 600mm - Designing, fabricating, installation and finishing of replica of treasure chest in 1800's of size approximately 1.2M x .60M . The chest is to be a filled treasury box with Indian treasure of that time. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/terracotta/clay or other material with highly precise aesthetic properties. . The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 2nos. 18. Haryana Gateways model 1- 6500mm x 1500 mm - Designing, fabricating, installation and finishing scenography recreation of monuments like badli ki sarai, haveli gateway of bahadurgarh etc. as scaled models of size as per design. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/random rubble masonry/mud/timber/thatch/sarkanda/fabric/glass/terracotta or other material with highly precise aesthetic properties. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 2nos. 19. Hansi fort monuments model - 10000mm x 3500 mm - Designing, fabricating, installation and finishing scenography recreation of monuments like Hansi fort gate of tentative size 10m x 3.5m with height upto 4m or scale as per design. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/masonry/mud/timber/thatch/sarkanda/fabric/glass/terracotta or other material with highly precise aesthetic properties. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 1nos. 20. Rao tula Ram Haveli model - 2500mm x 1500 mm - Designing, fabricating, installation and finishing scenographic recreation of Rao tula ram haveli. of tentative size 2.5m x 1.5m with height upto 2.5m. The haveli model to be made with the provision of peekholes for viewing indoor scenes having miniature models, indoor scenography good for multiple interactions such as pepper ghost. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as masonry/mud/timber/thatch/sarkanda/fabric/glass or similar complete with indoor/ outdoor elements FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/MDF/Corian/acrylic/concrete/ mud/brick/ metal/terracotta/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties as per design. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Volume : 15 Cum. 21. Trees- 1000mm trunk - Providing and installing realistic trees having details like peeled bark, bark texture,war markings etc. in FRP/MDF/fabric/plywood/solidwood/terracotta/ metal as per design with adequate structure in wood/metal. The height of the tree to be 3500mm-4500mm (variable as per design requirements). The tree radius to be varying from 450-1000mm. The finish of the tree high quality duco/pu paint/acrylic paint/ as per approved by the museum design consultant. Provision for openable shutter, concealed hinges, magnetic lockable system with provision for placing touch pad/ tablets or any other artefacts as per design. The rate to be inclusive of base plate required for fixing the tree durably with the floor. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The shop drawings to be vetted by the structural consultant and as per the satisfaction of engineer in charge. Any other paint/top coating required to match the aesthics of the well to be included. Qty. : 20 nos. 22. Vegetation - Designing, fabricating, installation and finishing of 2D/3D elements to create scenography of dried vegetation scenegraphy elements such as, shrubs, dried wheat crop, wheat sheaves, haystacks, etc.to represent agricultural land of Haryana with the floor having cracks and burns, heaps of straw kept in the field as per design made jute/ bamboo/ mud/ FRP/M.S./wood/MDF/terracotta or similar as per design. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 180 sqm. 23. Human sculpture - Providing and fixing of a scene consisting of 6 human figures, khat, utensils made out of metal - such as copper and nickel/ brass in 1:1 scale or 25% larger than real scale for imapct; made and finished with copper/brass/nickel , sculpture should be weather proof with colour variation as per design. The sculpture describes the scene of people gathering in common space in refuge camps and singing regional folk songs to keep each others moral high. The installation to be made in collaboration with artist. Design to be approved by museum design consultants. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Human figures to be supported it accessories like utensils and other materials creating a scene of people spent their evenings at battle grounds. Refer images given in tender presentation. The installation to be made weather proof. Specialized artist/sculpturist on board for the installations to take necessary prior approvals from museum design consultant before execution. Qty. : 1 nos.

NS 1. Sanjhi artwork - Designing, providing and fixing of artwork installation depicting the various scenes and themes related to the battles occurred in various regions of Haryana made by special artist demonstrating the rich Haryana crafts of Sanjhi artwork. The tentative size of the artwork installation is 3000x3000mm,depending on the site conditions and the design proposal by the artist. Original Sanjhi art effect to be done but with any material changes as per required for durability. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The artwork needs to be fixed on base framework of varied basework as per the respective artwork as per the approved detail/design. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. Please refer to the design presentation for further details. Rates are excluding the panelling cost but including the installation and other allied items. Area : 45 sqm. 2. Hills scenography models - Designing, fabricating, installation and finishing scenography recreation hills/mounds of variable height from floor to ceiling upto 3m mud/thatch/FRP/wood/metal or similar complete with all the details as per the reference images. The installation to depict various regions and terrains in Haryana during 1857. Eg. Raisena hills, etc. and to highlight the elevated locations of some villages where the battles were fought. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as masonry/ mud/ timber/ thatch/ sarkanda/ fabric/ glass or similar complete with indoor/ outdoor elements FRP/ POP/ foam/ hay/ straw/ white cement/ synthetic wax/resin/fabric/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/terracotta/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 120 sqm. 3. Haryana arms making tunnel installation - Providing and fixing of a haryana fort tunnel installation good for the visitor to walk in made of approximate size 3mx5m. The installation to highlight the scenes of arms being made inside the tunnel like spaces in various monuments. The finish to be to good for project. The tunnel to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as masonry/mud/timber/thatch/sarkanda/fabric/glass or similar complete with indoor/ outdoor elements FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/MDF/Corian/acrylic/concrete/ mud/brick/ metal/ terracotta/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Length : 5m 4. Well Interactive - Providing and fixing and finishing on site of a well structure similar to community wells of 1857. The well to be made of approx. 3m/4m dia along with columns etc. as per design with required 50x50x4 mm square sections of 50mm dia pipe for structure along with masonry/mud/timber/thatch/sarkanda/fabric/glass or similar complete with indoor/ outdoor elements FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/MDF/Corian/acrylic/concrete/ mud/brick/flexible ply/ metal/ terracotta/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties.The installation/shell to include appropriate provision for incorporating required hardwares/sensors/equipments,etc. for a complete experience. Appropriate measures to be taken for easy modulation operation, maintenance, security along with lockable systems. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 1nos. 5. Haryana diorama - Designing, providing and fixing artwork with 2-3 layered diorama depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/ terracotta/Frp elements fixed on the diorama. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The finish should be such that it compliments the aesthetics of the space meeting the thematic intent. The installation quality and finish should conform to the International standards of museums. The artwork is to be installed as per the design on vertical/horizontal/angled surfaces. The framework of the installation is to be made of a 50X50MM M.S. sections structure. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional.The diorama shall be used for varying heights up to the height of a maximum of 4000mm . Please refer to the design presentation for further details. the rates are included in paneling/base required for fixing of the artwork in the desired design pattern as approved by the museum design consultant. Area : 36 sqm. 6. Human silhouettes - Corten steel (1200x2400mm) - Providing and fixing of Free Standing human silhouette of varying sizes such as 1000x1000mm, 2000x2000mm, 3000x3000mm to celebrate the freedom fighters made in 5-8mm thk corten steel/ MS panel with laser cutting/CNC cut Artwork in 50% of the area of signage surface. The rate is inclusive of providing the front surface/both surface with sand blasting for a rustic finish. The rate is also inclusive of providing a base for the corten steel sheet made of ms/corten steel sections/L angles to form a framework. The base to be factory bended finish embedded in the floor with fasteners as per requirement and depth in the ratio of the superstructure for stability as approved by the engineer in charge . Item Rate to include jointing and finishing of corten steel with recommended framework/ clamping system all complete. clear height (height of substructure to be embedded in the base to be considered for overall height). The finish to be inclusive of paint finish such as duco, oil finish and other required metal finishes. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Qty. : 20nos. 7. Human silhouettes - Corten steel (3000x2400mm) - Providing and fixing of Free Standing human silhouette made in 10mm thk corten steel/ MS panel with laser cutting/CNC cut Artwork in 50% of the area of signage surface. The rate is inclusive of providing the front surface/both surface with sand blasting for a rustic finish. The rate is also inclusive of providing a base for the corten steel sheet made of ms/corten steel sections/L angles to form a framework. The base to be factory bended finish embedded in the floor with fasteners as per requirement and depth in the ratio of 1:3 of the superstructure for stability. Item Rate to include jointing and finishing of corten steel with recommended framework/ clamping system all complete. Size - 3000mm X 2400mm clear height (height of substructure to be embedded in the base to be considered for overall height).Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Qty. : 10nos. 8. Debris scattered around with remains - Part 1: Providing and fixing of construction debris depicting remains/ ruins of Indian region's buildings, war objects, utilitarian objects in 1857 made in F.R.P./terracotta/materials as peer necessary with MS Frame structure , broken objects over an area of 50 sqm Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional as per the design intent. The debris replica to be made in combination of the following 4 sizes approximately: Type 1. 50x50x50 mm Type 2: 200X200X200mm Type 3: 300X300X300mm Type 4: 600X600X300mm Area : 51 sqm. 9. Haryana Interaction table (3500x1200mm) - Providing and fixing of table of size - 3.5m x 0.9m x 0.9m made in 50X50mm Square pipe(if needed 50mm diameter pipe can be used) c/c 450mm frame with 12mm commercial ply on top and finished with 12mm thick Corian/metal as per design, with provision of cove at the bottom. Provisions for niches to be made on top for tablet/screen fixing. Rate to exclude LED light fixture in cove with drivers and wiring. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Provision for openable shutter, concealed lockable system as per requirement of the installation for its maintenance and operation to be also provided. Inclusive of CNC/laser cutting for making slotting/ louvers/ perforations for operations and maintanence. Provision for openable shutter as per requirement of the installation for its maintenance and operation to be also provided. Qty. : 1nos. 10. Haryana Interaction table 2 (kinetic) - Providing and fixing of table of size - 3.0m x 1.2m x 0.9m made in 50X50mm Square pipe(if needed 50mm diameter pipe can be used) c/c 450mm frame with 12mm commercial ply on top and finished with 12mm thick Coria/metal as per design, with provision of cove at the bottom. Provisions for kinetic models to be considered. Rate to exclude LED light fixture in cove with drivers and wiring. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Provision for openable shutter, concealed lockable system as per requirement of the installation for its maintenance and operation to be also provided. Inclusive of CNC/laser cutting for making slotting/ louvers/ perforations for operations and maintanence. Qty. : 1nos. 11. Haryana Interaction table 3 (model projection) - Providing and fixing of table of size - 3m x 0.9m x 0.9m made in 50X50mm/as per requirement Square pipe of desired thickness (if needed 50mm diameterpipe can be used) in a grid pattern at 450mm c/c both ways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions including fixing of 12mm to 18mm thk commercial ply/board of Greenply/Century ply or eqv. The cost is to be inclusive of top finished in 12mm thick Corian/metal of approved make and shade. The rate is also inclusive of providing stands on base made of wood/ms sections/corian to hold 6 nos of headset at desired location with finish as per approved design, with provision of cove at the bottom. The surface finish of the table and model should be good for projection. The cost should also be inclusive of all necessary adhesives, grinding, buffing etc for installation of corian on the base. Rate to exclude LED light fixture. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Provision for openable shutter as per requirement of the installation for its maintenance and operation to be also provided. The surface finish of the table and model should be good for projection. Qty. : 1nos. 12. Document table - Providing and fixing of table of size - 3m x 0.6m x 0.9m made in 50X50mm/as per requirement Square pipe of desired thickness (if needed 50mm diameterpipe can be used) in a grid pattern at 450mm c/c both ways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions including fixing of 12mm to 18mm thk commercial ply/board of Greenply/Century ply or eqv. The cost is to be inclusive of top finished in 6mm to 12mm thick Corian/metal of approved make and shade as per approved design, with provision of cove at the bottom. The surface finish of the table and model should be good for projection. The cost should also be inclusive of all necessary adhesives, grinding, buffing etc for installation of corian on the base. Rate to exclude LED light fixture. Qty. : 1nos. 13. VR experience Wall - Designing, fabricating, installation and finishing of 2D/3D diorama /artwork/ arches in 1-2 layers depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the diorama. Provision for led lighting between the layers to be considered as per lighting design required for the scenographywith materials frp/mdf/pop/acrylic/terracotta with multiple arches of varying sizes such as 1200mm x 2400mm, 1500x3000mm as per design. The arches to have all the provisions for incorporating T.V.'s/ projection screen within the arches. The basework of the arches to be150 mm overall thickness free standing partition up to 4 meter height consisting of ms hollow section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm flexible ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The cost is also to be inclusive of providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as approved by the Museum Consultant. The surface should be smooth enough for vinyl film application. Area : 85 sqm. 14. Haryana heroes installation - Designing, providing and fixing of artwork installation to celebrate the freedom fighters and their names of approximately 1000 in numbers with 2d/3d form developed by special artist in material such as M.S./S.S/Corten Steel/wood/glass/ terracotta with required necessary base work and frame work in metal/wood. The artwork is meant to be an sensory experience that evocate visitor emotions by completely immersing them in the artwork. The installation aims to be a master exhibit that leaves long lasting impression on the museum visitors. It is a collective experience that narrates and celebrates the story of all the leaders of Haryana whether known or unkown. The installation to be fixed/mounted on floor, walls, ceiling as required. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional.Artwork is to be designed by a special artist having prior experience of making large scale installations with such materials, past work to reflect sensitivity towards the translating emotions into physical form. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. : 1nos. 15. Phulkari fabric panelling - Providing and fixing of 75-150 mm overall thickness free standing partition up to 4 meter height consisting of ms hollow section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of up to 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm flexible ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The wooden panel will have 1" cushioning on top that will be finished on top with stain free custom made fabric skin, the fabric should be resistant to wear and tear, made of polyester/cotton/jute/khadi. Fabric to be embroidered in using phulkari weaving technique by a special artist as approved by museum design consultant. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The phulkari work cloth shall be used for full height panelling upto maximum height of 4000mm. Artwork for the cloth to be designed by special artist familiar with the craft and made by local artisans/craftsmen with past experience of the craft. Specialized artist on board for the Phulkari weaving to take necessary prior approvals from museum design consultant before execution. Rate to include cost of required wooden framework for paneling and cushioning. Area : 112 sqm. 16. Designing, fabricating, installation and finishing of replicas of objects such as earthen pots, sack of grains, farming tools, bricks, lakhauri bricks, lamps, lanterns, hookahs, jewellery, jute bags, wheat, rice etc. and any other scenography elements required to depict the culture of Haryana in FRP/wood/metal as per design. The replica to be of size as per scenography requirements. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. The finish to be as per required. Temperature controllers to be added. Qty. : 15nos. 17. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS India documentary show - The show to have the following components: Immersive documentary show - Providing and fixing of 360° immersive and interactive projection room having projection on walls and floor. The walls to be made of 75-150 mm overall thickness free standing partition up to 4 meter height consisting of ms hollow section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with required customised spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of upto 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm flexible ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The installation cost to include plastic projection finish paint on walls matt finish and high gain, columns & ceilings. The rate shall include scrapping, levelling & preparing the surface. Primer coat (Asian/ Nerolac/ Berger) + (minimum) 3 coats to get evenly spread quality finish (roller finish) of approved make, quality & finish shall be provided as directed by Museum Consultants. Finish with wall putti wherever necessary before paint. Area : 228 Sqm. Boat Seating installation - Designing, fabricating, installation and finishing wooden plank boat seating of tentative size 6000x1500mm having 4-6 seating platforms in materials such as hardwood/Commercial ply/metal sheets or similar materials complete M.S. framework as per required sizes for the stability of the structure to be considered. For scenography purpose supporting elements to be made in materials like frp / microtopping / metal / acrylic/ fabric as per necessary.The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution.Nos. 2 India documentary scenography elements - Designing, fabricating, installation and finishing of replicas of war objects related to the commute of 1800's such as horses, elephants, floating wooden plank, and similar as per design. The replica to be of size upto 2000x1200mm.The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Nos. 7 General notes - The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS 1. War at India scenography - In this gallery , the major monuments showcases the battle scenes in details in the different area of India at important monuments, cities along with major leaders where major battles took place across india i.e the Kashmiri gate Battle in Delhi, the Lucknow residency in Awadh, Sati Ghat in Kanpur, Kali Paltan Mandir in Meerut, will highlight their iconic elements i.e. Jhansi ki rani's horse and nan Rao's elephant, North West Frontier Province, Rohilkhand, Gond region etc. The following are the main components of the gallery: 2. war at meerut installation - Designing, fabricating, installation and finishing scenography recreation of monuments such as Kaali paltan temple of tentative size 3m x 3m with height upto 4m finished with stone/corian on both sides having top coating as per design approval. The setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall/floor with provision for all cabling wiring or any other mechanism required to make it functional, with a top cover of 12 mm-18mm commercial ply/board, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The cost is inclusive of fixing the frame to the floor/base/ceiling with necesary hardwares, fixtures, screw, nut-bolt etc all complete as per the satisfaction of engineer incharge. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. The back wall provided to be good for projection including providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. The surface should be smooth enough for vinyl film application. Remaining surface are on the walls to have layered surface depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the panel. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardwares, screws etc all complete as per direction of engineer in charge. The ply to be leved in a way that it is durable for fixing carpet/vinyl/stone/ips/microtoppin with adhesives, fixtures, hardwares along with all the edge detailing and profiles. Provision for integration of the projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. All the provisions required for hanging of any props projectors, equipments, canvasing any equipments to be considered. The gallery to have the finish in designed fabric to be suspended from the structural ceiling to complete the set up as per design. Area : 9 sqm. 3. War at Barrackpore installation - Designing, fabricating, installation and finishing scenography recreation of barrackpore cantonement area of tentative size 5m x 3m with height upto 4m. The cantonments to have various architectural elements such as arches, wooden louvered windows, colonade, pitched roof, cornices, mouldings finished in materials such as FRP/ POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/ clay/ mud/ timber/ thatch/fabric/glass or other material with highly precise aesthetic properties as approved my museum design consultant. The setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall/floor with provision for all cabling wiring or any other mechanism required to make it functional, with a top cover of 12 mm-18mm commercial ply/board, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The cost is inclusive of fixing the frame to the floor/base/ceiling with necesary hardwares, fixtures, screw, nut-bolt etc all complete as per the satisfaction of engineer incharge. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. The back wall provided to be good for projection including providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. The surface should be smooth enough for vinyl film application. Remaining surface are on the walls to have layered surface depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the panel. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardwares, screws etc all complete as per direction of engineer in charge. The ply to be leved in a way that it is durable for fixing carpet/vinyl/stone/ips/microtoppin with adhesives, fixtures, hardwares along with all the edge detailing and profiles. Provision for integration of the projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. All the provisions required for hanging of any props projectors, equipments, canvasing any equipments to be considered. The gallery to have the finish in designed fabric to be suspended from the structural ceiling to complete the set up as per design. Area : 15 sqm 4. war at Kanpur installation - Designing, fabricating, installation and finishing scenography recreation of sati chaura ghat of tentative size 12m x 3m with height upto 4m having structural framework for walls, floor, steps, platforms, bastions in M.S. sections upto 75x75mm covered in 18mm ply, finished on exterior faces in materials such as red sandstone/ lakhori bricks wet cladded/ dry cladded as per approved in design. The ghat to have various architectural elements such as arches, colonade, parapets, domes, cornices, mouldings etc. as per design reference. For scenography purpose elements to be made in materials like polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/glass natural material building or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 36 sqm 5. war at Lucknow installation - Designing, fabricating, installation and finishing scenography recreation of lucknow residency of tentative size 7.5m x 3m with height upto 4m, finished on both sides in materials such as FRP/POP/plaster with mud plaster/micro topping/ paint finish or similar as per approved design. The setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall/floor with provision for all cabling wiring or any other mechanism required to make it functional, with a top cover of 12 mm-18mm commercial ply/board, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The cost is inclusive of fixing the frame to the floor/base/ceiling with necesary hardwares, fixtures, screw, nut-bolt etc all complete as per the satisfaction of engineer incharge. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. The back wall provided to be good for projection including providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. Remaining surface on the walls to have layered surface depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the panel. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardware, screws etc all complete as per direction of engineer in charge. The ply to be levelled in a way that it is durable for fixing carpet/vinyl/stone/ips/microtopping with adhesives, fixtures, hardwares along with all the edge detailing and profiles. Provision for integration of the projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. All the provisions required for hanging of any props projectors, equipments, canvasing any equipments to be considered. The gallery to have the finish in designed fabric to be suspended from the structural ceiling to complete the set up as per design. The residency to have various architectural elements such as arches, wooden louvered windows, colonade, pitched roof, cornices, mouldings etc. as per design reference made in materials like thatch/polished hardwood/ fabric/frp/POP/foam/hay/straw/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area :22.5 sqm 6. war at jhansi installation - Designing, fabricating, installation and finishing model replica of Jhansi fort of tentative size 5m x 1.5m with height upto 4m having structural framework for walls, floor, ceilings in M.S. sections upto 75x75mm covered in 18mm ply, finished on both sides in materials such as stone rubble/red lakhori bricks/sandstone wet cladded/ dry cladded as per approved in design. The fort to have various architectural elements such as gateways, arches, bastion, merlon, parapets, etc. as per design reference. For scenography purpose elements to be made in materials like polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/glass natural material building or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 7.5 sqm 7. war at Santhal & Gond installation - Providing and fixing of 2d/3d artwork in multiple materials (MDF, acrylic, bendable acrylic solid surface, M.S,Fabric,glass) with CNC/LASER/uv print and finished with PU paint and any other as per the design on vertical/horizontal/angled surface. The base frame work of 50X50MM MS framework structure and 12mm ply if required with provision of cove lighting. the edge profile should be smooth and sturdy. Area : 15sqm 8. war at Bihar installation - Providing and fixing of 2d/3d artwork in multiple materials (MDF, acrylic, bendable acrylic solid surface, M.S,Fabric,glass) with CNC/LASER/uv print and finished with PU paint and any other as per the design on vertical/horizontal/angled surface. The base frame work of 50X50MM MS framework structure and 12mm ply if required with provision of cove lighting. the edge profile should be smooth and sturdy.Area: 14sqm 9. war at Hyderabad installation - Designing, fabricating, installation and finishing scenography recreation of Hyderabad residency of tentative size 3.6m x 2.5m with height upto 4m having structural framework for walls, floor, ceilings in M.S. sections upto 75x75mm covered in 18mm ply, finished on both sides in materials such as red lakhori bricks/sandstone wet cladded/ dry cladded as per approved in design. The residency to have various architectural elements such as arches, wooden louvered windows, colonade, pitched roof, cornices, mouldings etc. as per design reference made in materials like thatch/polished hardwood/ fabric/frp/POP/foam/hay/straw/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 9 sqm 10. war at Aurangabad installation - Designing, fabricating, installation and finishing scenography recreation hills/mounds of variable height from floor to ceiling upto 3m in area of size 7m x 2m with mud/thatch/FRP/wood/metal or similar complete with all the details as per the approved reference image. M.S. framework in required sizes for the stability of the structure to be considered. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as masonry/mud/timber/thatch/sarkanda/fabric/glass or similar complete with indoor/ outdoor elements FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/MDF/Corian/acrylic/concrete/ mud/brick/ metal/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties as per approved by the museum design consultants. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution.The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 14 sqm 11. war at Delhi installation - Designing, fabricating, installation and finishing model replica of Kashmiri gate of tentative size 8.5m x 5m with height upto 4m having structural framework for walls, floor, ceilings in M.S. sections upto 75x75mm covered in 18mm ply, finished on both sides in materials such as stone rubble/red lakhori bricks/sandstone wet cladded/ dry cladded as per approved in design. The fort to have various architectural elements such as gateways, arches, bastion, merlon, parapets, etc. as per design reference. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/random rubble masonry/mud/timber/thatch/sarkanda/fabric/glass or other material with highly precise aesthetic properties. The cost is inclusive of providing and fixing two nos. of 12 mm thick toughened glass panels of approx. size 1500x2400mm fixed to the floor/ceiling with all necessary channels, hadwares, fixtures, adhesives etc, including application of matte film/3M Vinyl/eqv for projection on one side. The surface finish to be good for projection. The installation quality, mechanism and finish should conform to the International standards of museums. The installation to include the cnc cutting/etching of artwork on upto 50% of the surface. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 42.5 sqm 12. war at Bareilly installation - Designing, fabricating, installation and finishing model replica of jail cell in bareilly of tentative size 5m x 2.5m with height upto 4m having metal bars/hollow pipe sections of desired thickness on upto 3 sides including the cost of fixing the ms bars on ms plate of desired size and thickness to the floor/ceiling with necessary hardware, fixture, screws, nut bolts etc all complete to make the structure stable as per approved design. The stucture to be vetted by structural consultant. The jail cell to have various architectural elements replicating the cell interiors element, plinths, carpet etc. as per design reference. The base should be good for projection. For scenography purpose elements to be made in materials like polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/glass natural material building or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 12 sqm 13. war at Assam installation - Designing, fabricating, installation and finishing scenography recreation of assam residency of tentative size 3m x 2m with height upto 4m, finished on both sides in materials such as FRP/POP/plaster with mud plaster/micro topping/ paint finish or similar as per approved design. The setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall/floor with provision for all cabling wiring or any other mechanism required to make it functional, with a top cover of 12 mm-18mm commercial ply/board, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The cost is inclusive of fixing the frame to the floor/base/ceiling with necesary hardwares, fixtures, screw, nut-bolt etc all complete as per the satisfaction of engineer incharge. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. The back wall provided to be good for projection including providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. Remaining surface on the walls to have layered surface depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the panel. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardware, screws etc all complete as per direction of engineer in charge. The ply to be levelled in a way that it is durable for fixing carpet/vinyl/stone/ips/microtopping with adhesives, fixtures, hardwares along with all the edge detailing and profiles. Provision for integration of the projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. All the provisions required for hanging of any props projectors, equipments, canvasing any equipments to be considered. The gallery to have the finish in designed fabric to be suspended from the structural ceiling to complete the set up as per design. The residency to have various architectural elements such as arches, wooden louvered windows, colonade, pitched roof, cornices, mouldings etc. as per design reference made in materials like thatch/polished hardwood/ fabric/frp/POP/foam/hay/straw/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 12 sqm

NS 1. 2d artwork - Providing and fixing of Acrylic/MDF/MS/corten steel with paint CNC/Laser cut artwork installed on site with necessary hardware/framework/as per manufacture specifications and site conditions.Necessary finish materials to be considered, to make the surface abrasion resistant as per approval by Museum Design Consultant. as per conceptual design provided by Museum consultants. Area : 20 sqm 2. British Army officers model - Designing, fabricating, installation and finishing 3d model sculpture of British Army officer of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 3 Nos. 3. British Army Men with props model - Designing, fabricating, installation and finishing 3d model of British Army officer of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props and mount such as Horse/ Elephant/ cart to be recreated as per design reference having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 2 Nos. 4. Indian soldier on foot model - Designing, fabricating, installation and finishing 3d model of Indian infantry soldier of Colonial India of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 8 Nos. 5. Indian soldier on horse model - Designing, fabricating, installation and finishing models of Indian infantry soldier of Colonial India of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props and mount such as Horse/ cart to be recreated as per design reference having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 5 Nos. 6. Indian horse - Designing, fabricating, installation and finishing models of Indian Horse in1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props to be recreated as per design reference having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and suitable accessories, ridin gears etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 5 Nos. 7. Indian Leader- Male - Designing, fabricating, installation and finishing models of Indian male leader of 1857 rebellion in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 3 Nos. 8. Indian Leader- Female - Designing, fabricating, installation and finishing model of Indian female leader of 1857 rebellion in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 2 Nos. 9. Indian Villager- male, female - Designing, fabricating, installation and finishing models of Indian Village person (male, female) of various regions of India of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable farming tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 5 Nos. 10. Indian cattle/ farm animals - Designing, fabricating, installation and finishing model of Indian cattle/ farm animals such as sheep, goat, cow etc. in1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props to be recreated as per design reference having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories with state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 5 Nos. 11. Indian Tribal person- male, female - Designing, fabricating, installation and finishing models of Indian Tribal person (male, female) of various regions of India of 1857 era in 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements including props having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The mannequins to have accurate adornments and accesories such as headgear, clothes, suitable tools, weapons, etc. and state-of-the-art hyper-realistic features with attention to details such as skin texture, skin tones, hair, physical attributes etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The mannequins/sculptures to be developed in an actual form/finish with realistic representation of the required theme/mood. Minor elements to support the setting/scenography/surroundings to be included in the cost. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 5 Nos. 12. Cart - Designing, fabricating, installation and finishing model of Indian cart of 1857 era 1:1 Scale or upto 25% larger/smaller than real scale as per scenography requirements having structural framework in wood, covered in ply/gypsum or other suitatble material, finished in materials such as corian/ FRP/POP/ paint/ microtopping/ synthetic wax/resin/fabric or other material with highly precise aesthetic properties. Models to have realistic features and attention to detail such as joinery, texture, colour etc. with frame made of MS/wood/FRP/FRP/POP and finishes in paint/microtopping to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 2 Nos. 13. Treasury Chest replica 600mm x 300mm - Designing, fabricating, installation and finishing of replica of treasure chest in 1800's of size approximately .60M x .40M in FRP/wood/metal as per design. The chest is to be a filled treasury box with Indian treasure of that time. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The replicas to have state-of-the-art hyper-realistic features with attention to details such as texture, tones, patterns etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 10 Nos. 14. Treasury Chest replica 1200mm x 600mm - Designing, fabricating, installation and finishing of replica of treasure chest in 1800's of size approximately 1.2M x .60M . The chest is to be a filled treasury box with Indian treasure of that time. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The replicas to have state-of-the-art hyper-realistic features with attention to details such as texture, tones, patterns etc. to be recreated as per design reference. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Qty. 2 Nos. 15. Lithograph type 1 - Providing and Installation of freestanding glass graphic panels, with UV printed/ vinyl graphics on both sides of the sandwich glass, opaque film/vinyl to be sanwiched between two 12 mm thk toughened glass, of size upto 1200mm in width and 2400mm in height , fixed from top and bottom with approved fixing mechanism/hardware as per design. Sample graphic panel and its content and design needs to be approved by museum consultant before production. The installation to include the cnc cutting/etching of artwork on upto 50% of the surface. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. Qty. 10 Nos. 16. Lithograph type 2 - Providing and Installation of freestanding glass panels with 12 mm thk toughened glass, of size upto 1200mm in width and 2400mm in height , finished in matte film/vinyl pasted for making glass surface good for projection fixed from top and bottom with approved fixing mechanism/hardware as per design. Sample graphic panel and its content and design needs to be approved by museum consultant before production. Qty. 10 Nos. 17. Torch pick up table - Providing and Fixing of artefact table of size 4000x750x900 mm with base made of 50X50mm hollow sections of desired thickness with appropriate spacing and necessary welding at junctions including applying of required coats of steel primer on sections. The cost is inclusive of providing and fixing 12mm-18mm thk commercial ply/board of approved make on MS frame work including necessary hardwares,screws etc all complete to make the structure functional as per the satisfaction off engineer incharge. The top to be finished in 12 mm thk corian of approved make and shade fixed to the ply with silicone adhesives including buffing and polishing of the surface as per approved drawings. The corian top will be etched with artwork. The remianing area to be painted in duco of approved shade with provision of cove at the bottom. Rate to exclude LED light fixture in cove with drivers and wiring. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Provision for openable shutter, concealed lockable system as per requirement of the installation for its maintenance and operation to be also provided. Inclusive of CNC/laser cutting for making slotting/ louvers/ perforations for operations and maintanence. Qty. 2 Nos. 18. India AR Wall( leaf craft panelling) - Providing and fixing 150 mm overall thickness free standing partition up to 4 meter height consisting of ms hollow section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm flexible ply conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes on both sides having bend radius as little as 100mm, ideal for tight radius work with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The wooden panel will have the palm leaf artwork interwoven as per design. The artwork should be resistant to wear and tear and shall be used for full height panelling upto maximum height of 4000mm. Artwork to be designed by special artist familiar with the craft and made by local artisans/craftsmen with past experience of the craft. Specialized artist on board for the palm weaving to take necessary prior approvals from museum design consultant before execution. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 80 sqm 19. Flag ceiling - Providing, fixing and installation of ceiling installation made of flags of various regions during 1857 in printed fabric such as cotton/linen/canvas or similar of variable sizes of width upto 1500mm and length up to 4000mm. The fabric to be suspended from ceiling with approved fixing detail as per the direction of the museum design consultant. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 135 sqm 20. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Tunnel Experience - Following are the main components of the tunnel experience: Tunnel shell - Providing and fixing 150mm overall thickness curved free standing partition and arched ceiling as per design of up to 4.7 meter height consisting M.S. framework of 50X50mm 75X75mm or as per site requirements of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with ms base plate of desired size and thickness with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, skylights, electrical conduits, switch boards etc. wherever required. The cost to be inclusive of applying one coat of steel primer of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 12mm to 18 mm Flexible ply conforming to BWR grade of Greenply/Duroply/Century ply or similar makes on one side having bend radius as little as 100mm , ideal for tight radius work with edge profiles including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, including jointing and finishing to a flush finish with recommended jointing. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The strength of the shell to be approved by the structural engineer of the contractor. The tentative size of the tunnel is 78m x3m with height 4m. The indoor curved surface to have random rubble finish with specialized interior finishes such as micro topping/concrete rendering/ FRP/ flexible grc/ stone rubble cladding/lime plaster as per design. Specialized interior paint finishes to be used to final touch-ups. The installation quality, mechanism and finish should conform to the International standards of museums. The installation to include the cnc cutting/etching of artwork on upto 50% of the surface. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 234 sqm Tunnel Ramp - Providing and fixing of M.S./aluminium sheet ramp floor made of 50x50mm/ 75x75mm/ 100x100mm of core size min 4mm MS structure dully fixed on floor with 300x300x10mm plate fastened on the laid PCC.The top cover of the structure to be in micro topping/concrete rendering/ FRP/ flexible grc/ stone rubble cladding over 18 mm Flexible ply conforming to BWR grade of Greenply/Duroply/Century ply or similar . The height of the bridge to vary from ground level to 2100mm . The bridge to have provisions to accomodate underground display cases. an The structure to be vetted by structural consultant keeping in mind the live load required. All Mild steel will be coated with anti-rust coating, duco paint and all complete with all necessary hardware, equipment's and colour approved by museum Consultants. Ramp tentative size - 3000x 78000mm. Length : 78m General note - The installation quality, mechanism and finish of the installation should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS 1. This gallery is meant as a memorial and reminder of the valour and determination of the people who participated in the war despite knowing that war brings destruction and despair for everyone who is exposed to the war. It brings with itself devastation,damage and casualties. This gallery is a reminisce of the ruination,annihilation, massacring and wreckage that the war left us with. More than that, it is a memoire of the courage and endurance of the revolutionaries who fought in the war. To bring these emotions into space the gallery is designed with the materials that are designed to be broken, burnt, destroyed to evocate the feelings of war chaos. 2. Atrocities at meerut installation - Designing, fabricating, installation and finishing of artistically designed ruins/ burnt/ charred/broken scenography recreation of monuments such as Kaali paltan temple of tentative size 3m x 3m with height upto 4m. The setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall/floor with provision for all cabling wiring or any other mechanism required to make it functional, with a top cover of 12 mm-18mm commercial ply/board, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The cost is inclusive of fixing the frame to the floor/base/ceiling with necesary hardwares, fixtures, screw, nut-bolt etc all complete as per the satisfaction of engineer incharge. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. The back wall provided to be good for projection including providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. Remaining surface are on the walls to have layered surface depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the panel. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardwares, screws etc all complete as per direction of engineer in charge. The ply to be leved in a way that it is durable for fixing carpet/ vinyl/ stone/ ips/ microtopping with adhesives, fixtures, hardwares along with all the edge detailing and profiles. Provision for integration of the projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. All the provisions required for hanging of any props projectors, equipments, canvasing any equipments to be considered. The installation quality, mechanism and finish should conform to the international standards of museums. The commissioned artist/ execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 9 sqm 3. Atrocities at Barrackpore installation - Designing, fabricating, installation and finishing of artistically designed ruins/ burnt/ charred/ broken scenography recreation of barrackpore cantonement area of tentative size 5m x 3m with height upto 4m. The cantonments to have various architectural elements in a distorted/damaged/broken finish such as arches, wooden louvered windows, colonade, pitched roof, cornices, mouldings finished in materials such as FRP/ POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/ clay/ mud/ timber/ thatch/fabric/glass or other material with highly precise aesthetic properties as approved my museum design consultant. The setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall/floor with provision for all cabling wiring or any other mechanism required to make it functional, with a top cover of 12 mm-18mm commercial ply/board, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The cost is inclusive of fixing the frame to the floor/base/ceiling with necesary hardwares, fixtures, screw, nut-bolt etc all complete as per the satisfaction of engineer incharge. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. The back wall provided to be good for projection including providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. Remaining surface are on the walls to have layered surface depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the panel. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardwares, screws etc all complete as per direction of engineer in charge. The ply to be leved in a way that it is durable for fixing carpet/vinyl/stone/ips/microtoppin with adhesives, fixtures, hardwares along with all the edge detailing and profiles. Provision for integration of the projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. All the provisions required for hanging of any props projectors, equipments, canvasing any equipments to be considered. The gallery to have the finish in designed fabric to be suspended from the structural ceiling to complete the set up as per design Area : 15 sqm 4. Atrocities at Kanpur installation - Designing, fabricating, installation and finishing of artistically designed ruins/ burnt/ charred/ broken scenography recreation of sati chaura ghat of tentative size 12m x 3m with height upto 4m having structural framework for walls, floor, steps, platforms, bastions in M.S. sections upto 75x75mm covered in 18mm ply, finished on exterior faces in materials such as red sandstone/ lakhori bricks wet cladded/ dry cladded as per approved in design. The ghat to have various architectural elements such as arches, colonade, parapets, domes, cornices, mouldings etc. as per design reference. For scenography purpose elements to be made in materials like polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/glass natural material building or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 36 sqm 5. Atrocities at Lucknow installation - Designing, fabricating, installation and finishing of artistically designed ruins/ burnt/ charred/ broken scenography recreation of lucknow residency of tentative size 7.5m x 3m with height upto 4m finished on both sides in materials such as FRP/POP/plaster with mud plaster/micro topping/ paint finish or similar as per approved design. The setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall/floor with provision for all cabling wiring or any other mechanism required to make it functional, with a top cover of 12 mm-18mm commercial ply/board, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The cost is inclusive of fixing the frame to the floor/base/ceiling with necesary hardwares, fixtures, screw, nut-bolt etc all complete as per the satisfaction of engineer incharge. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. The back wall provided to be good for projection including providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. Remaining surface on the walls to have layered surface depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the panel. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardware, screws etc all complete as per direction of engineer in charge. The ply to be levelled in a way that it is durable for fixing carpet/vinyl/stone/ips/microtopping with adhesives, fixtures, hardwares along with all the edge detailing and profiles. Provision for integration of the projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. All the provisions required for hanging of any props projectors, equipments, canvasing any equipments to be considered. The gallery to have the finish in designed fabric to be suspended from the structural ceiling to complete the set up as per design. The residency to have various architectural elements such as arches, wooden louvered windows, colonade, pitched roof, cornices, mouldings etc. as per design reference made in materials like thatch/polished hardwood/ fabric/frp/POP/foam/hay/straw/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 22.5 sqm 6. Atrocities at jhansi installation - Designing, fabricating, installation and finishing of artistically designed ruins/ burnt/ charred/ broken scenography recreation of Jhansi Fort of tentative size 5m x 1.5m with height upto 4m having structural framework for walls, floor, ceilings in M.S. sections upto 75x75mm covered in 18mm ply, finished on both sides in materials such as stone rubble/red lakhori bricks/sandstone wet cladded/ dry cladded as per approved in design. The fort to have various architectural elements such as gateways, arches, bastion, merlon, parapets, etc. as per design reference. For scenography purpose elements to be made in materials like polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/glass natural material building or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 7.5 sqm 7. Atrocities at Hyderabad installation - Providing, fabricating, installation and finishing of burnt/charred/broken scenography recreation of Hyderabad residency of tentative size 3.6m x 2.5m with height upto 4m having structural framework for walls, floor, ceilings in M.S. sections upto 75x75mm covered in 18mm ply, finished on both sides in materials such as red lakhori bricks/sandstone wet cladded/ dry cladded as per approved in design. The residency to have various architectural elements such as arches, wooden louvered windows, colonade, pitched roof, cornices, mouldings etc. as per design reference made in materials like thatch/polished hardwood/ fabric/frp/POP/foam/hay/straw/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 9 sqm 8. Atrocities at Delhi installation - Providing, fabricating, installation and finishing of artistically designed ruins/ burnt/charred/broken scenography recreation of Kashmiri gate of tentative size 8.5m x 5m with height upto 4m having structural framework for walls, floor, ceilings in M.S. sections upto 75x75mm covered in 18mm ply, finished on both sides in materials such as stone rubble/red lakhori bricks/sandstone wet cladded/ dry cladded as per approved in design. The fort to have various architectural elements such as gateways, arches, bastion, merlon, parapets, etc. as per design reference. The models to have structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay/random rubble masonry/mud/timber/thatch/sarkanda/fabric/glass or other material with highly precise aesthetic properties. The cost is inclusive of providing and fixing two nos. of 12 mm thick toughened glass panels of approx. size 1500x2400mm fixed to the floor/ceiling with all necessary channels, hadwares, fixtures, adhesives etc, including application of matte film/3M Vinyl/eqv for projection on one side. The surface finish to be good for projection. The installation quality, mechanism and finish should conform to the International standards of museums. The installation to include the cnc cutting/etching of artwork on upto 50% of the surface. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 42.5 sqm 9. Atrocities at Bareilly installation - Designing, fabricating, installation and finishing of artistically designed burnt/charred/broken scenography recreation of jail cell in bareilly of tentative size 3m x 3m with height upto 4m having metal bars/hollow pipe sections of desired thickness on upto 3 sides including the cost of fixing the ms bars on ms plate of desired size and thickness to the floor/ceiling with necessary hardware, fixture, screws, nut bolts etc all complete to make the structure stable as per approved design. The stucture to be vetted by structural consultant. The jail cell to have various architectural elements replicating the cell interiors element, plinths, carpet etc. as per design reference. The base should be good for projection. For scenography purpose elements to be made in materials like polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/glass natural material building or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 9 sqm 10. Atrocities at Manipur installation - Designing, fabricating, installation of artistically designed ruins/ burnt/ charred/ broken/ finishing scenography recreation of Manipur residency of tentative size 3m x 2m with height upto 4m finished on both sides in materials such as FRP/POP/plaster with mud plaster/micro topping/ paint finish or similar as per approved design. The setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall/floor with provision for all cabling wiring or any other mechanism required to make it functional, with a top cover of 12 mm-18mm commercial ply/board, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The cost is inclusive of fixing the frame to the floor/base/ceiling with necesary hardwares, fixtures, screw, nut-bolt etc all complete as per the satisfaction of engineer incharge. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. The back wall provided to be good for projection including providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. Remaining surface on the walls to have layered surface depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the panel. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardware, screws etc all complete as per direction of engineer in charge. The ply to be levelled in a way that it is durable for fixing carpet/ vinyl/ stone/ ips/ microtopping with adhesives, fixtures, hardwares along with all the edge detailing and profiles. Provision for integration of the projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. All the provisions required for hanging of any props projectors, equipments, canvasing any equipments to be considered. The residency to have various architectural elements such as arches, wooden louvered windows, colonade, pitched roof, cornices, mouldings etc. as per design reference made in materials like thatch/polished hardwood/ fabric/frp/POP/foam/hay/straw/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/ natural material building materials such as thatch roof or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 6 sqm 11. Atrocities-Road roller - Providing, fabricating, installation and finishing of artistically designed ruins/ burnt/ charred/ broken scenography recreation of Road Roller crushing Indian civilians of 1857 colonian India used by the British, of tentative size 3m x 3m with height upto 4m having structural framework for structure in M.S. sections upto 75x75mm covered in 18mm ply, finished on both sides in materials such as FRP/POP/ cement plaster/micro topping/ paint finish or similar. The installation quality, mechanism and finish should conform to the International standards of museums. The installation to include the cnc cutting/etching of artwork on upto 50% of the surface. The cost is also inclusive of designing, fabricating, installation and finishing of replica of a road roller of desired size in FRP/wood/metal/cast iron/ as per design. The road roller to be a part of a projection show hence the surface finish to be good for projection having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 6 sqm 12. Atrocities-Public hanging - Providing, fabricating, installation and finishing of artistically designed ruins/ burnt/charred/broken scenography recreation of public hanging structure with hanging noose of 1857 colonian India used by the British, of tentative size 3m x 2m with height upto 4m. The setup includes backdrop fixed on M.S frames 50x50mm/75x75mm hollow sections fixed on the wall/floor with provision for all cabling wiring or any other mechanism required to make it functional, with a top cover of 12 mm-18mm commercial ply/board, conforming to BWR grade on both sides with the provision of infilling of Acoustical insulation within the Frame structure. The cost is inclusive of fixing the frame to the floor/base/ceiling with necesary hardwares, fixtures, screw, nut-bolt etc all complete as per the satisfaction of engineer incharge. The wood to be treated with anti-termite solution, formaldehyde free, fire retardant. The back wall provided to be good for projection including providing surface base with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. Remaining surface are on the walls to have layered surface depicting the scenography made up of 18mm thick ply/board duly CNC laser cut done as per design painted with duco paint and acrylic/corian/metal/Frp elements fixed on the panel. Provision for led lighting between the layers to be considered as per lighting design required for the scenography. The backdrop will have a raised platform as a base for the show. It will be made up of 50x50mm, 75x75mm of 2-4mm thick core M.S. section duly welded with Ms base plate of desired size and thickness fixed with fasteners/ nut bolts with the M.S. sections to be duly painted with one or two coats of steel primer. The cost to include the application of 18mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to MS sections with all necessary fixtures, hardwares, screws etc all complete as per direction of engineer in charge. The ply to be leved in a way that it is durable for fixing carpet/ vinyl/ stone/ ips/ microtopping with adhesives, fixtures, hardwares along with all the edge detailing and profiles. Provision for integration of the projection, lighting and sound with the single controller to be considered. Excluding the cost of servers projectors, lighting. All the provisions required for hanging of any props projectors, equipments, canvasing any equipments to be considered. The installation quality, mechanism and finish should conform to the international standards of museums. The commissioned artist/ execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 6 sqm

NS 1. Atrocities-Execution by cannons - Providing, fabricating, installation and finishing of artistically designed ruins/ burnt/ charred/ broken scenography recreation of public execution by blowing from a cannon of 1857 colonian India used by the British, of tentative size 3m x 2m with height upto 4m having structural framework in wood/ M.S. sections upto 75x75mm covered in 12mm-18mm commercial ply/board, finished on both sides in materials such as FRP/POP/ cement plaster/micro topping/ paint finish or similar. The surface finish to be good for projection. The installation quality, mechanism and finish should conform to the International standards of museums. The installation to include the cnc cutting/etching of artwork on upto 50% of the surface. The cost is also inclusive of designing, fabricating, installation and finishing of replica of a cannon of desired size in FRP/wood/metal/cast iron/ as per design. The cannon to be a part of a projection show hence the surface finish to be good for projection having structural framework in wood/metal with wire mesh or other suitatble material, finished in materials such as FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ microtopping/clay or other material with highly precise aesthetic properties. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 6 sqm 2. Atrocities Ruins-Debris - Providing, fabricating, installation and finishing of artistically designed ruins/ burnt/charred/broken scenography recreation of war ruins including debris such as broken/burnt bricks, sticks, haystack, canes, armours etc with materials such as original material/FRP/POP etc specially crafted and laid/fixed on setup with necessary hardwares if required. Materials such a wood/ply/ M.S. sections to be used for structural form finished on both sides in materials such as FRP/POP/ cement plaster/micro topping/ paint finish or similar as per approved design. The surface finish to be good for projection. The installation quality, mechanism and finish should conform to the International standards of museums. The installation to include the cnc cutting/etching of artwork on upto 50% of the surface. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 153 sqm 3. Amphitheatrical steps - Providing and fixing of amphithatrical stepped seating made up of M.S. angle in tube/ISMB dully welded with the base plate of desired size and thickness duly fixed with necessary fixtures, fasteners/nut bolts etc all complete with the existing base. The structure to be vetted by structural consultant keeping in mind the live load required. covered in the fabric/rug designed by a special artist of punja dari artwork of Haryana as per approved having 4-5 seating platforms of high risers of 300mm with intermediate climbing steps. The structure of the stepped auditorium seats to be in M.S./ wooden section of size as per structural requirements. The railing to be provided as per as per design. The seating to be 9.8m wide and 2.7m in length. The steps to be covered in carpet made of weaving craft of punja dari by the special artist/craftsmen in the approved pattern and shade. The carpet to be anti skid, excellent sound insulation,easy to maintain with self levelling compound of desired colour, applied as per the area demarcated in the drawing. The carpet to cover the amphitheatrical seating and the mezzanine floor.The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Qty. 1 nos. 4. Custom design finishes: - To evocate the feelings of war chaos, the gallery is consists of designed finishes that are broken, burnt, destroyed. Following are the finishes that are to be designed in such way: 5. Customized IPS flooring - Providing and laying of custom designed 75mm thick IPS flooring. The cost is inclusive of providing an under layer of concrete of 63mm thickness with a mix of CC 1:2:4 (1 part cement, 2 parts coarse sand and 4 parts graded stone aggregate-12.5 mm and downgraded). The top layer to be 12mm thick. The flooring shall be laid in panels of uniform sizes of 2 SqM or as per approved design.The surface of the RCC slab shall be roughened up with brushes while the concrete is green. Before laying the floor, the laitance, loose materials, cake of mortar dropping shall be removed and the surface of the slab hacked and coat of cement slurry @2.75 kg of cement per SqM. shall be applied so as to get a good bond between the slab and IPS. If IPS has to be provided on lean concrete no slurry is required. The top finish coating to be as per approved by the Museum Design Consultant. Area : 376 sqm 6. Customized Gravel Flooring - Providing and laying of customised gravels/ stone aggregate as specified by the museum design consultants on the desired locations inside/outside of the buildings mentioned as per the approved drawings. It shall consist of naturally occurring (uncrushed, crushed or broken) river bed shingle or pit gravel. It shall be sound, hard and clean. It shall be free from flat particles of shale or similar laminated material, powdered clay, silt, loam, adherent coating, alkali, vegetable matter and other deleterious substances. Pit gravel shall be washed if it contains soil materials adhering to it. These shall conform to IS 383 unless otherwise specified. Area : 62 sqm 7. Customized Mud flooring - Providing and laying of 10mm - 12mm Thk. Mud plaster with 5% cement mixed with local mud and chopped and sifted straw laid in a single unjointed layer rammed thoroughly upto a desired thickness. The finish layer applied to be a mixture of cow dung and clay with a thickness of min 1mm on with rapid curing on existing false floor similar to ground surface of various archeology excavation sites found in haryana, with MS wire mesh gauge as per area demarked on drawing , as per approval by museum design consultant. Area : 76 sqm 8. False Flooring - 150mm - Providing and Fixing of False floor with MS tubular section of 50mmX50mm/75mmX75mm/as per requirement of desired thickness with appropriate spacing and necessacr welding at junctions including application of 25mm to 32mm thick BWR grade plywood/board of Greenply/Century ply or eqv fixed to base with 2mm thk MS plate of desired size and base properly welded with all fasteners and necessary hardware's with edge profiles, beadings etc all complete as per approved design. The rate is also inclusive of two coats of MS primer on the frame structure and one to two coats of anti termite oil finish on ply board. Height of False flooring to be considered is 150mm alongwith provision of cove as per design requirement. Area : 36 sqm 9. Mangalore tile ceiling - Providing and fixing custom designed terracotta tile ceiling of size and proportion of a custom brick with supports as per design. Inclusive of M.S. T angles/wooden rafters as per structural consultants. The ceiling to be complete with all the necessary hardwares and accessories required for the ceilig suspension and durability. Area : 200 sqm 10. Burnt Flag ceiling - Providing, fixing and installation of ceiling installation made of flags of various regions during 1857 in printed fabric such as custom made cotton/linen/canvas or similar of variable sizes of width upto 1500mm and length up to 4000mm. The fabric to be suspended from ceiling with approved fixing detail as per the direction of the museum design consultant. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Area : 135 sqm 11. Custom made Red sandstone - Providing and laying of designed burnt, charred, broken red sandstone flooring with custom artwork in varying sized of 300x300mm, 600x300mm, 600x1200mm in the pattern as per the design. (Require specs from old boq's-PMC) Area : 42 sqm 12. Micro topping finish on walls - Providing and fixing micro- topping wall system composed of polymer (not water) mixed with special cement admixture of desired shade, texture and approved make as per the direction of museum design consultant. The rate to be inclusive of preparing a sub base free of dust, laitance, oils or any loose material with a provision of any expansion, contraction and crack inducing joints to avoid cracking, unevenness and faults, including application of Epoxy-coat mixed with 20% quartz-sand (0,2-0,5mm) as adhesion primer and covering thoroughly the surface with quartz-sand on substrate. Rate includes the application of two coats of base coat with 0.5mm coarse sand used as gauge evenly spread upto maximum thickness of 0.5mm. Followed by application of upto two coats of very thin layer of finish coat or high-performance coat without coarse sand for smooth appearance. The final coat is to be sealed with acrylic or PU sealer all complete as per the direction of engineer incharge. Approved make : Bharat Flooring/idealworks/eqv Area : 145 sqm 13. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Events at Ambala -Interaction - This intercation is Incendiary fires interaction is to have the following components: Object table - Providing and fixing of table of size - 8m x .75m x 0.9m and height 0.5m made in 50X50X4mm Square pipe(if needed 50mm diameterpipe can be used) c/c 450mm frame with 12mm flexible ply on sides and 18mm commercial board on top finished with 12mm thick bendable acrylic solid surface as per design, with provision of cove at the bottom above the skirting. Rate to exclude LED light fixture in cove with drivers and wiring. Table to have niches/depressions to for keeping the RFID/gesture based objects finished in corian. The cost should also be inclusive of all necessary adhesives, grinding, buffing etc for installation of bendable acrylic solid surface on the base. Cost to nnclude of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional/structurally stable. Provision for openable shutter as per requirement of the installation for its maintenance and operation to be also provided. Qty. : 1 nos. Objects - Providing, designing and fabrication of 8nos. real/replicas of objects such as earthen pots in mud/ F.R.P./ wood/ Metal/ corian as per approved design and satisfaction of museum design consultant. Approximate size: 50x50x50 mm, 200X200X200mm, 300X300X300mm. Each object to have provisions for RFID/sensors chips to be installted within the objects. (exclusive of the cost of the sensor) Qty. : 16 nos. General note - The installation quality, mechanism and finish of the installation should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Ambala war set design - The ambala war set design has following components: Part A- Diorama - Providing and fixing of set design of 5-6 scenes setup of length 5m, height 4m and depth as per design and site. The framework of the scenes to be made in hardwood of sections having columns and beams of size150x300mm, 300x300mm or as per structural and site requirements, framework of 50x50mm/75x75mm M.S. sections with 18mm thick commercial ply with 6mm thick MDF finished in duco paint/vinyl as per design. The set up details: - Scene set up type 1: Providing & fixing of Ultra Gain projection screen of high quality material of Standard sizes from 42”-134” & self adhesive material. The screen should be seamless with no joints and the projection outcome should not be compromised. All provision for mounting the screen onto the framwork like aluminum/ any other profile, edge detail to be included in the rate. Make - ProDisplay or equivalent. - Scene set up type 2: Providing and fixing of layered diorama in multiple material (MDF, Acrylic, bendable Acrylic solid surface, MS,Fabric,glass) with CNC/LASER/uv print at 2-3 layers finished with PU paint/any other as per the design on vertical/horizontal/angled surface. The base frame work of 50X50MM M.S. framework structure with provision of cove lighting. The edge profile should be smooth and sturdy. (the cost to exclude the cost of light) Part B- Ceiling - Designing , providing and fixing of wood carved ceiling by an expert of Haryana wood carving craft. Inclusive of all - fixtures, fittings, hardware, hanging system, electrical, mechanical or any other mechanism required to make it functional. Area : 182 sqm. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS India backlit map - Providing and fixing backlit false floor upto 300mm height floor. The structure to be made of hydraulic adjustable jack with solic acrylic blocks duly fixed on the floor with necessary hardwares, nuts bolts etc all complete. Providing and fixing of the Ms framing of 50mmx50mm with thickness of upto 4mm in a grid pattern customised as per the design scheme duly welded to the base with base plate of desired size and thickness to be done if required and can be optional as per the satisfaction of engineer in charge. The cost is inclusive of toughened sandwich glass upto 30mm thk with extra clear 3M transparent protective film made in customised size as per appropriate grid design. Each panel to have reverse graphic/ ceremic printing/digital printing etc as per approval of museum design consultant. Each panel to be fixed in butt joint with fixing of glass with heavy duty silicone adhesive and the base to be fixed on MS framework with required adhesives as per the requirement. The rate is inclusive of providing acrylic sheets for housing the LED modules placed as per the requirement. Each tile illuminated by a powerful LED panel to be controlled with a centrally controlled DMX system as per the design scheme. The structure to be vetted by a structural engineer. Area : 80 sqm. Providing and fixing backlit wall made of upto 12-18mm thick toughened printed glass panels with extra clear 3M transparent protective film made in customised size as per appropriate grid design.. The structure to be made with solid acrylic blocks duly fixed on the wall with necessary hardwares, nuts bolts etc all complete. Ms framing of 25x25mm/ 50mmx50mm with thickness of upto 4mm in a grid pattern customised as per the design scheme duly welded to the base with base plate of desired size and thickness. Each panel to have reverse graphic/ ceremic printing/digital printing etc as per approval of museum design consultant. Each panel to be fixed in butt joint with fixing of glass with heavy duty silicone adhesive and the base to be fixed on MS framework with required adhesives as per the requirement. The rate is inclusive of providing acrylic sheets for housing the LED modules placed as per the requirement. Each tile illuminated by a powerful LED panel to be controlled with a centrally controlled DMX system as per the design scheme. The structure to be vetted by a structural engineer. Area : 72 sqm. General notes - The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Void Experience - Designing, providing, and fixing a set design based on the design intent and references provided for the gallery. The gallery intends to depict the void that the war had brought with all the destruction, loss of life, and injustice. The gallery to have dark aesthetics with the black/charcoal curved walls and ceiling finished in concrete rendering/micro topping/ special wall and ceiling finishes as per design, a designed tree of approximate dia. 10m made of FRP/metal/ wood/metal mesh placed on the mound as per design having hung objects of size upto 0.75m x 1.8m, the visitor pathways of width approximately 2m to be provided in corten steel/M.S. sheets partially submerged in water from sides with the adequate framework provided for the floor and the sides, the gallery to be filled with black water up to 600mm deep in a room size of radius 10m. Resting mounds in organic shapes are to be provided for the visitors to sit and observe. Visitors experience the dripping water sound and visuals in the gallery for which the tree to have channels for water that drips down at timed intervals. Provisions for olfactory experience are to be considered. All provisions for the water filling, changing, and maintenance are to be taken into account. Part of the ceiling of the gallery to be made in demountable PVC Stretch Ceiling welding with harpoon ready to install. (Fire Rated to European Standards b-s1-d0/b-s2-d0/B1/b2*) With 5 years warranty on stretch membrane seam ruptures & profile. All joints to be fused / provided with approximate interface trims to be able to demount the stretch ceiling to access the lights. The stretch ceiling shall be installed as per details drawing using proprietary aluminium profile complete as per manufacturer's installation guidelines and as per approved shop drawings in line with the design intent and approval by the museum design consultant (Make - Barisol/ Euroceil or equivalent ). Providing 5 year manufacture warranty, adhering to manufacture installation guidelines and achieving maximum light. The structural framework for walls, ceiling, pathways, installations to be considered in design and vetted by the structural engineer as per required. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. General notes - The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Haryana Industrial advancement installation - Providing, fabricating and fixing of a installation to highlight the importance of industrial advancement of Haryana made of various machinery parts like gears, truck parts, tyres, headlights, pistons, ball bearings, etc, of agricultural equipments, automobiles, such as tractors, motorcycles or any other parts /abstraction of parts required for the installation. The installation is around the columns with tentative size 3m x 3m and height of 4m. The various parts to be procured and conserved from the industrial scrap, replica of the parts to be made as per required in materials such as metal/ frp/ wood as per design. The installations to have moveable and rotating parts as per design. The base installation to be in FRP/POP/foam/hay/straw/white cement/ synthetic wax/resin/fabric/ paint/ having structure as per required. Provision for the framework of the installation to be considered to meet the design aesthetics and the structural requirements. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Storytelling objects - Designing, providing and fixing of object based installations in individual museum galleries made by special artist narrating the story of the galleries.The object/artwork/installation/sculpture/elements will signify/narrate depicting the theme/narrative of the gallery and evoke emotions within the visitors in line. It will convey the message of the overall museum as the accents in each gallery. These highlight elements of the museum will collectively define the story of the museum, and will become the anchor points in the narrative. The tentative size to be 2mx2mx1m made in polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ plywood/ Corian/ acrylic/ concrete/ mud/brick/ metal/ terracotta materials of Harayana craft. The artist on board to develop the design of the object based on the various stories as per the content of the museum. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS AR Tribute interaction- Designing, providing and fixing of the outdoor tribute experience in which the visitor interacts with a physcial object such as a wreath, garland or flower petals have their pictures clicked while performing the tribute ceremony as a memoire of the visit to museum. The interaction to be designed and technically evolved by the team of experts as per the design theme. The installation to be inclusive of all the AV equipment such as camera, sensors, display device or any other device as required for the functioning of the interaction. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. General notes- The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Stamping interaction installation- Development of content/quotations appropriate to be printed/ projected on any surface such as wall, floor,ceiling, etc. which are anecdotes from the museum galleries, creates an introspective narrative and develops an inspiring storyline throughout the museum. The content/quotes to be in sync with the content of the museum. The content to be developed for a total 10-12 locations within the museum. The content to be conceived and developed by special artists such as Ankur Warikoo or equivalent who have been India's best seller author in the past 5 years and have prior experience in educating/creating awareness among youth of India. The commissioned artist/author on board for the content to take necessary prior approvals from museum design consultant. General notes- The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Location marker signages- Providing and fixing of free-standing outdoor signages to commemorate the first war of independence and to inform visitors about the history of various locations of war in Haryana/India of size upto 3m(W) x 3m(H) made up of combination of materials such as corten steel/ MS panel/ Alucobond/ Ionised Aluminium/glass with laser cutting/CNC cut Artwork in upto 50% of the area of signage surface. These signages to have graphics as per approved textual content, pictures, lithographs or similar [proofread by authorised Professional] with UV printing technique/ outdoor vinyl/lenticular printing technique as per design approval. These installations to be installed in various parts of Haryana/India as an extention to the museum, the job to include the surface preparation of the finalized location of the signages including excavation, civil work, surface finish work or similar as per required . The rate is also inclusive of providing a base for the corten steel sheet made of ms/corten steel sections/L angles to form a framework. The base to be factory bended finish embedded in the floor with fasteners as per requirement and depth in the ratio of the superstructure for stability as approved by the engineer in charge . Item Rate to include jointing and finishing of corten steel with recommended framework/ clamping system all complete. Height of substructure to be embedded in the base to be considered for overall height. The finish to be inclusive of paint finish such as duco, oil finish and other required metal finishes. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. General notes- The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Stamping interaction installation- Designing, fabricating, installation and finishing table of size - .6m x .6m x .75m made in 50X50mm Square pipe(if needed 50mm diameter pipe can be used) c/c 450mm frame with 12mm commercial ply on top and finished with 12mm thick Corian/ metal sheet , with provision of cove at the bottom. The table to be used by the visitors for stamping the booklets with the designed stamps. The stamps to have graphic/ textual content that the visitor can imprint on their booklet as a memoire to the museum. Inclusive of equipments required for stamping and table to have provision to accomodate the same. Rate to be quoted shall include the cost of custom designed graphics / 2D artwork , illustrations / artwork and Copywriting and editing of textual content as per conceptual design provided by museum design consultant. Size of the stamp & graphical content should be in sync with the size of the stamping booklet. The table to be finished in corian/metal with powder coating/duco finish of approved make and shade. The top finish will be etched with artwork. The remaining area to be painted in duco of approved shade. Provision for openable shutter, concealed lockable system as per requirement of the installation for its maintenance and operation to be also provided. Rate to exclude LED light fixture in cove with drivers and wiring. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Inclusive of CNC/laser cutting for making slotting/ louvers/ perforations for operations and maintanence. Under special conditions, the size of the table may vary and cost considered to be under prorata basis proportionately. General notes- The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Stamping passport booklet - Concept design, detail design and print ready files for the following: 1. Stamping booklet of passport size approximately 100 mm x 120mm. The book would be of 20-30 pages atleast with premium print and paper quality. The book's content should explain the museum galleries' goals and provide a concise summary of their contents. The book to be made using 2d/3d graphics/illustration of international quality and proffessional images of the museum interors and context. 2. Desigining the booklet cover, back and atleast 10 leaflets should be connected to the museum narrative supported with 2d/3d graphics/illustration of international quality / proffessional images of the museum interors and context in a very compact format. Common Note: The cost of sampling to check material and print quality, layouting, graphics design to be covered in the item. The design language including colors, layout, imagery and typography to be in synchronisation with the museum branding theme. Stepwise approval on approach, concept design, pages layout, font type and sizes, coverdesign, pages design and color scheme should be taken, approval to be taken on the basis of samples received. The cost would also include 10 copies each of all the above mentioned 5 final products. The required copywriting and proofreading of international quality in the required languages to also be included in the item rate. copy-writing as per the requirement of the book. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Mashal interaction points - Providing and fixing the mashal replicas on walls/floors for interaction of 'lighting the torch'. These mashals to be lit up upon sensory actions such as touch/motion etc. The mashals to be made of materials such as metal/ wood/frp etc. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Utilitarian objects replicas - Designing, fabricating, installation and finishing of replicas of daily objects such as utencils, small storages, chests, candle stands, earthen pots, sack of grains etc. in FRP/wood/metal as per design. The replica to be of size upto 600x600mm or as per scenography requirements. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. The finish to be as per required. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS International museum documentary - Making of an international documentary on the theme of how indians still carry the burden of slavery in tangible and intangible forms. The master edit of the documentary will be in total of 60-80 minutes supported by 10-12 short edits of 6-8 minutes each which will be showcased in the museum at different locations. Detailed film making process to be followed from conception to final screening. The film need to be made in collaboration with discovery/netflix/epic channel/ equivalent appropriate platform. The cost of coordination for executing the collaboration to be included in the rate of this item. The film will be made with multiple interviews of internationally known and relevant personaities like the Honourable PM of India, Honourable PM of UK, PM/authorities of other common wealth nations, freedom fighters, people who have seen the independance happening, Monarchs of the UK, Honourable memebers of the parliament and cabinet ministers, recognised authors and writers, notable historians, journalists and critique, directors - all relevant national and international personnel who have doen respectable work in relation to the documentation/archicing/representation of the stories related to British Rule in India. Cost of minimum 15 nation wide shoot locations and 5 international shoot locations with necessary equipment and logistic support to be considered as par of the rate of the item. A celebrity anchor from Haryana like Randeep Hudda/equivalent to be considered for anchoring the overall film. Original background score to be developed with renowned national level artists. Appropriate 2d/3d rendering, best camera shoot equipment, lighting accessories, recording equipment, drone shoot equipment and anyother required equipment to be inculded in the rate of the film. The bidder shall qoute for a compiled master documentary plus 10-12 shorts edits of the same documentary. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Lost objects of war artwork - Part A - Designing, providing and fixing of object based installations at various locations in the museum made by special artist narrating the story of the objects that were lost by our nation in the war. It shall evoke the feeling of loss among the visitors. These highlight elements of the museum will collectively define the story of the museum, and will become the anchor points in the narrative. The tentative size to be .45mx.45mx.45m made in polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ plywood/ Corian/ acrylic/ concrete/ mud/brick/ metal/ terracotta materials of Harayana craft. The artist on board to develop the design of the object based on the various stories as per the content of the museum. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Part B - Providing and Fixing of artefact table of size 600x600x900 mm with base made of 50X50mm MS/wooden hollow sections of desired thickness with appropriate spacing and necessary welding at junctions including applying of required coats of steel primer on sections. The cost is inclusive of providing and fixing 12mm thk commercial ply of approved make on MS frame work with necessary hardwares,screws etc all complete. The top to be finished in 12 mm thk corian of approved make and shade fixed to the ply with silicone adhesives including buffing and polishing of the surface as per approved drawings. The corian top will be etched with artwork. the display box to be finished in corian from all sides. The remianing area to be painted in duco of approved shade. a)Providing and fixing of display glass case of 8 M.M thick toughened glass of height 250mm on all four side fixed on 12mm-15mm thk aluminium channels and top placed of size as/specifications/design. The cost is inclusive of fixing of all edges with extra clear silicone with necessary fixtures and allen key locking arrangement (not to be visible on the face) b)Providing and fixing of 6 mm thick white lacquered glass on the top and all four sides of base to place the artefacts with edges bevelled at an angle on all edges as per approved detail drawings fixed to a ply base with extra clear silicone . General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Remnants of war artwork - Part A - Designing, providing and fixing of object based installations at various locations in the museum made by special artist narrating the story of the tangible/intangible remants of war that were left by the Britishers and are still existing in our nation even after more than 75 years of Independence. It shall be an experience of revelation for the vistors seeing these objects. These highlight elements of the museum will collectively define the story of the museum, and will become the anchor points in the narrative. The tentative size to be .45mx.45mx.45m made in polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ plywood/ Corian/ acrylic/ concrete/ mud/brick/ metal/ terracotta materials of Harayana craft. The artist on board to develop the design of the object based on the various stories as per the content of the museum. The installation quality, mechanism and finish should conform to the International standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. Part B - Providing and Fixing of artefact table of size 600x600x900 mm with base made of 50X50mm hollow sections of desired thickness with appropriate spacing and necessary welding at junctions including applying of required coats of steel primer on sections. The cost is inclusive of providing and fixing 12mm thk commercial ply of approved make on MS frame work with necessary hardwares,screws etc all complete. The top to be finished in 12 mm thk corian of approved make and shade fixed to the ply with silicone adhesives including buffing and polishing of the surface as per approved drawings. The corian top will be etched with artwork. the display box to be finished in corian from all sides. The remianing area to be painted in duco of approved shade. a)Providing and fixing of display glass case of 8 M.M thick toughened glass of height 250mm on all four side fixed on 12mm-15mm thk aluminium channels and top placed of size as/specifications/design. The cost is inclusive of fixing of all edges with extra clear silicone with necessary fixtures and allen key locking arrangement (not to be visible on the face) b)Providing and fixing of 6 mm thick white lacquered glass on the top and all four sides of base to place the artefacts with edges bevelled at an angle on all edges as per approved detail drawings fixed to a ply base with extra clear silicone . General note - The installation quality, mechanism and finish should conform to the International standards of museums. Artwork is to be designed by a special artist familiar with the craft and made by local/indigenous artisans/craftsmen with prior experience in the craft. The artist assigned should take all the necessary approvals from the museum design consultant. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. Please refer to the design presentation for further details. The bidder/execution agency must refer to all the research, design and reference presentations and video links provided by the museum design consultants for understanding the concept, intent and quality of the installation. All the items required to meet the intent of the installation shall be under the scope of the bidder/execution agency. Please note that the crafts defined in the installation are subject to be interchanged during the detail design stage. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Jail cell replicas - Designing, fabricating, installation and finishing scenography recreation of jail cell of tentative size 1.5m x 2m with height upto 4m having metal bars/hollow pipe sections of desired thickness on upto 3 sides including the cost of fixing the ms bars on ms plate of desired size and thickness to the floor/ceiling with necessary hardware, fixture, screws, nut bolts etc all complete to make the structure stable as per approved design. The stucture to be vetted by structural consultant. The jail cell to have various architectural elements replicating the cell interiors element, plinths, carpet etc. as per design reference. The base should be good for projection. For scenography purpose elements to be made in materials like polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/glass natural material building or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS False staircase - Designing, fabricating, installation and finishing scenography recreation of a tunnel staircase of tentative width 2m having 10-12 steps to the floor/ceiling with necessary hardware, fixture, screws, nut bolts etc all complete to make the structure stable as per approved design. The stucture to be vetted by structural consultant. The base should be good for projection. For scenography purpose elements to be made in materials like polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/glass natural material building or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Underground display cases - Providing and fixing Artefact casing of variable size of 600mmx1200mm, 900mmx1500mm with MS/wooden framework and w.p.c board and enclosed with Metal sheet/Ply of size as per design and extra clear glass casing printed/lacquered glass base for the artefacts/replicas as per the specifications and drg as approved by the Engineer in charge. The top glass casing to be of 15mm thick extra clear factory laminated glass double layered with 3m protection film, scratch free, extra clear film of thickness up to 0.4-2mm. The glass to be of customized sizes as per the curvature of the floor. The artefact casing finish to be in finishes such as duco/metal oils/specialized metal and wood finishes as approved by museum design consultants. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Arms - Designing, fabricating, installation and finishing scenography installation having 400-500 arrows of actual size of the indian tribal community. the arrows to The stucture to be vetted by structural consultant. The base should be good for projection. For scenography purpose elements to be made in materials like polished hardwood/ fabric/frp/POP/foam/ paint/ microtopping/ clay/ MDF/ Corian/ acrylic/ concrete/ mud/brick/ metal/glass natural material building or other material with highly precise aesthetic properties as per approved by the museum design consultants. The installation to be complete with the framework required to support the models. The installation quality, mechanism and finish should conform to the international standards of museums. The installation is inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. These signature installations to be made by specialized agencies having experience in making sculptures, set design, mannequins, wax models, artwork etc. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge.

NS Haryana craft furniture - Designing, providing, and fixing of 3-4 typology of furniture in local haryana crafts made out of wood/ fabric/ jute/ niwar/ cotton strands or equivalent. The furniture to have high quality finish, with premium material, complete with cushioning, springs etc. required for the comfort of the visitors. The furniture to be designed such that the visitor can lay on it to look at the ceiling installation. The cost includes providing and fixing of 75-150 mm overall thickness framework to form a base consisting of ms/wooden section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions. The cost to be inclusive of applying one coat of steel primer/ anti termite solution of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 19mm plyboard conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The framewok will have cushioning on top of appropriate thickness that will be finished on top with stain free custom made fabric skin, the fabric should be resistant to wear and tear, made of polyester/cotton/jute/khadi. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge. The size of the furniture to be : (1500X3000X450mm)

NS Haryana craft furniture - Designing, providing, and fixing of 3-4 typology of furniture in local haryana crafts made out of wood/ fabric/ jute/ niwar/ cotton strands or equivalent. The furniture to have high quality finish, with premium material, complete with cushioning, springs etc. required for the comfort of the visitors. The furniture to be designed such that the visitor can lay on it to look at the ceiling installation. The cost includes providing and fixing of 75-150 mm overall thickness framework to form a base consisting of ms/wooden section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions. The cost to be inclusive of applying one coat of steel primer/ anti termite solution of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 19mm plyboard conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The framewok will have cushioning on top of appropriate thickness that will be finished on top with stain free custom made fabric skin, the fabric should be resistant to wear and tear, made of polyester/cotton/jute/khadi. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge. The size of the furniture to be : (1200X2500X450mm)

NS Haryana craft furniture - Designing, providing, and fixing of 3-4 typology of furniture in local haryana crafts made out of wood/ fabric/ jute/ niwar/ cotton strands or equivalent. The furniture to have high quality finish, with premium material, complete with cushioning, springs etc. required for the comfort of the visitors. The furniture to be designed such that the visitor can lay on it to look at the ceiling installation. The cost includes providing and fixing of 75-150 mm overall thickness framework to form a base consisting of ms/wooden section 50X50mm/75X75mm/ as per site requirement of desired thickness in a grid pattern with 600mm c/c spacing bothways (horizontal and vertical) or at required spacing near opening, with necessary fixing at junctions. The cost to be inclusive of applying one coat of steel primer/ anti termite solution of approved quality on the framework. The rate to be also inclusive of providing and installing top cover of 19mm plyboard conforming to BWR grade of Greenply/ Duroply/ Century ply or similar makes with edge profiles, including the cost of necessary hardware, screws etc all complete as per approved drawings and the direction of engineer in charge. The framewok will have cushioning on top of appropriate thickness that will be finished on top with stain free custom made fabric skin, the fabric should be resistant to wear and tear, made of polyester/cotton/jute/khadi. Inclusive of all - fixtures, fittings, hardware, hanging system, or any other mechanism required to make it functional. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge. The size of the furniture to be : (600X600X450mm)

NS Reception video wall film - Development of content appropriate for a LED wall of approximately 7mts. X 4 mts. The content will contain a film of duration 3 minutes introducing the museum and its related facilities at the Ambala War Memorial. The film will have mixed media content including information graphics, illustrations, 2D animation/Motion Graphics/3D animation and models with live action shoot wherever required as per the theme and storyline of the film. The content should be supported by ambient sound design. The rate for photoshoot and video shoot of all work including equipment like drones, special camera/ other necessary equipment for the overall museum to be included. The cost for any resources such as music composers, artists, instrumentalists, sound engineers, recording studio charges, and all recording and sound processing charges etc. to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size.

NS Revolutionary- Touch Kiosk film content - The AV will include projection film of duration 1-2 minutes taking about the journey of the visitors in the museum. An interactive exhibit with touch-based application that triggers the projection on the touch screen, with 8-10 personalities as virtual guides. This interactive exhibit's content will provide the visitor with cues/triggers to choose a revolutionary guide for the overall museum experience. The output will be a visual and interactive guide with personalized content appearing in the screen in front of the visitor, one visitor can interact with the screen at once with two headphones for sound output with each screen. These audio visual virtual guides will be famous personalities belonging to Haryana. Content using 2D animation/Motion Graphics/3D animation, illustration, modelling wherever required as according to theme and storyline. Ambient soundscape suitable with the visual content to be developed for the overall gallery along with personalized content running in headphones w.r.t to the chosen language by the visitor. All sound processing, dubbing, mixing, etc. costs are includes in the cost. The cost for any resources such as music composers, singers, artists, instrumentalists, sound engineers, recording studio charges, etc. required to be included in the cost. The content should have original music score. User Experience should be easy and impactful.

NS Arrival of british gallery immersive projection mapping - The AV of 3-5 minutes will represent the arrival of the East India Company in India in 1600's from the coastal region for the purpose of trading and eventually into Haryana, followed by the British settlement in Ambala in 1800's. The projection show will be done on the concave projection surface on the wall surface along with a 2D- 3D setup of a house interior and view from the window of the house. The film screening will include mapping on physical 3D elements i.e. a EIC ship on a dock, house settlements, British Barracks and a tree in the context to bind all elements together. Since the projection is not only on the wall projection surface, but also physical elements, the AV show should be developed to make the most of the screen designed to create visual effects to enhance the viewer's experience. the AV will contain mixed media content including 2D animation/Motion Graphics/3D animation and models with Live action shoot wherever required as according to script and storyline. The content should be supported by sound design and Voiceover in 1-2 languages of duration 3-5 minutes.

NS Personality shoot - The AV shoot of 8-10 personalities of Haryana of duration 1-2 minutes of content of known peronalities of Haryana e.g Kapil Dev,Neeraj Chopra, Virender Sehwag, Geeta Phogat, Manushi Chhillar, Vijender Singh, Saina Nehwal, Rajkummar Rao, Randeep Hooda, Rajendra Gupta and Sunil Grover etc and as per requirement appearing in various galleries and breakout spaces. These audio visual will act as the virtual guides will be famous personalities belonging to Haryana from diverse fields to ackowledge and appriciate the spirit and contribution of people of Haryananationally and internationally. These personalities will become the brand ambassadors of the museum and become the voice and face of the museum, its experience and amplify its reach, recognition and credibility. Live action shoot with required location/background and props according to theme and storyline. All equipments, camera, fixtures and jib etc are included in the cost. The following, but not limited to will be the roles and reponsibilites of the actors/ personalities for the shoot: • Understand and Interpret the role requirement by speech, gesture, and body movement to inform and entertain the audience for virtual guidance, holograms, voice overs or other media production. • Interpret the work of a writer under the instruction and support of a director. • Rehearse and memorize lines. • Take cues from director. • Use body language and movement to bring out the required emotion and theme. • Improvise the requirement of the narrative of the museum • Do voice-overs for virtual guide, audio system and guidance. • Discuss interpretation and delivery with other members of the director and design consultant. • Improve performance based on feedback from the director and design consultant. • Collaborate with other actors as part of an ensemble. • Promote productions using means such as interviews about plays or movies if required, this scope will not be included in the cost but may be added otherwise if required.

NS Ambala telegram projection - Silent projection on table highlighting the text of the famous telegram. The visual will appear on the table in a format to showcase that the text is being decoded from the morse code and unveiling in text format on the table. The rate to include required 2D animation, motion graphics, copy for subtitles, appropriate background music (if any).

NS SAFETY EQUIPMENT (Electrical & UPS Room only - Supply and fixing shock treatment chart duly mounted on a frame with 3~5mm thick glass as required.

NS SAFETY EQUIPMENT (Electrical & UPS Room only - : Rubber Mat suitable for 11KV & 1.1 K V system spread in front of the HT & L T Panel.

NS SAFETY EQUIPMENT (Electrical & UPS Room only - Rubber gloves as per relevant IS for Electrical system operation (HT & LT)

NS SAFETY EQUIPMENT (Electrical & UPS Room only - Providing first-Aid Box as approved by St. John Ambulance Brigade/ Indian Red Cross conforming to IS2217-1963.

NS SAFETY EQUIPMENT (Electrical & UPS Room only - : Fire Bucket Stand as per approved design by Fire Department.

NS SAFETY EQUIPMENT (Electrical & UPS Room only - : Fire Bucket filled with Sand

NS SAFETY EQUIPMENT (Electrical & UPS Room only - : Hand held ABC type fire fxtinguisher of capacity 2.5 Kg.

NS SAFETY EQUIPMENT (Electrical & UPS Room only - Foam fire extinguishers, portable type 9 lit capacity hanged on wall with bracket complete as required.

NS Elevator experience installation with a passenger platform size of 8 m Dia and an outer curved shell of 10 m diameter with 360' immersive projection over it. - Development of an immersive dome projection mapping film of duration 3-5 minutes introducing the visitors to the evolution of Haryana through ages. The content will include stories of recent times to the ancient times to take people back in time and visualize the land of Haryana, its history, surroundings, civilizations and the great battles fought on this land. The scenes will include glimpses and stories developed with actors, animation, VFX, shoot etc. for Origin of the name of the State, It is also known as Haryana ;the land an the abode of Aryas and home of the preachings of vedic cultures and other rites. During the olden period, this region was known as Brahmavarta, Aryavarta and Brahomoupdesa, the battle of Kurukshtra, it is also a region with an inter-mingling of various peoples and races, Haryana’s contribution to the making of the composite Indian culture has been remarkable in its own way. The essence of the audio visual will be that In spite of relentless pressure and ruthless persecutions over the years by different people and civilisations, a vast majority of people offered an unflinching resistance to the alien conqueror and their creed and showed a dogged persistence in shunning their contacts and maintaining their exclusiveness. The film will have mixed media content including 2D animation/Motion Graphics/3D animation and models with live action shoot, information graphics, illustrations, wherever required as per the theme and storyline of the film. The content should be supported by sound design and voiceover in 2 languages - Hindi and English. All necessary photoshoot and video shoot to be included in the cost. All film direction, cimeatography, editing, sound processing, dubbing, mixing, etc. costs are included in the cost. The cost for any resources such as music composers, singers, artists, instrumentalists, sound engineers, recording studio charges, etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size. The rate for photoshoot, video shoot, documentation of the related content to be included. The cost includes the human resources and suitable equipment’s required for the shoot. The cost includes drone shooting with appropriate equipment’s required to do the same. The film will have an original musical score to support the visuals.

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 400 sq. mm. A2XFY

NS Diorama Diorama installation with projection - The AV will include projection films of duration 30-60 seconds each depicting the prosperous events of India and highlight. These projections will be highlights to the great past the country had before the British arrived and took over everything. the projections will highlight events such as the building of different great monuments in India, the cultural events, birth of great leaders, harmonious and colourful culture of India . Content using 2D animation/Motion Graphics/3D animation, illustration, models with live action shoot wherever required as according to theme and storyline. The visual language has to be derived from the artforms, images, paintings and lithographs etc. as approved by the design consultant. Ambient soundscape suitable with the visual content to be developed. All necessary photoshoot and video shoot to be included in the cost. The cost for any resources such as actors, costume, script, director, cameraman, music director, composer etc. required to be included in the cost. The content should be made in appropriate resolution as per screen size.

NS VR - Development of interactive virtual reality content which will allow the visitors to visit the original surroundings of the time and place where the Britishers had arrived in India and eventually Haryana. The context in virtual reality using VR headsets will showcase the activities of British in different cities and setting up of their territories and developments in the regions i.e industries, militaries, cantonements, buildings and offices etc . 3D reconstruction of a court room where the Indian is being tried and given life sentence for stealing bread and no one is there to present the case of the Indian to protect him. the 3D construction will be done in game engines like Unity/Unreal. The VR interface should allow the user to choose the place/ destination using gaze control. Each setup will have minimum 5 interactive points with 2 min of playtime experience, that will reveal information in form of text/images/video about the events and incidents. The voice over/subtitles for the film will be done in 2 languages - Hindi and English. The rate to include all research, 3D modelling, required photo/video shoots, rendering, vfx etc required for the complete experience of the virtual tours. All necessary photoshoot and video shoot to be included in the cost. The cost for any resources such as actors, costume, script, director, cameraman, music director, composer etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size. Please refer video no.

NS Kinetic Model show - Development of a kinetic multimedia show of duration 3-5 mins, which gives an engaging experience of the different scenes of oppressions faced by the citizens of India. Since a large population in India is of farmers, the agricultural oppressions by the British effected people the most e.g. increase in taxes, collection oof taxes before harvest, indigo farming etc. which left the farmers poor and without food. The show will be curated with 5 physical kinetic models depicting the above mentioned scenes, each model will be moved with kinetic mechanism in the center of the gallery and the visitors would be able to look at the model and listen to the audio narrating a story related to the scene, each model will stay in the center upto 60 seconds. The model will have dramatic lighting to complement the narrative of the scene. content including information graphics, illustrations, 2D animation/Motion Graphics/3D animation, and models with live action shoot wherever required as per the theme and storyline of the film. The content should be supported by sound design and voiceover in 2 languages - Hindi and English. All necessary photoshoots and video shoot to be included in the cost. The cost for any resources such as director, music composers, singers, artists, sound engineers, recording studio charges, etc. required to be included in the cost.

NS interaction and films - This will include multiple projections and audio visuals of duration 1-2 minutes showcasing the scenes of oppressions faced by the citizens of India. The audio visuals will be divided into multiples videos varying with multiple causes which will be interactive and will be triggered via different interaction points synced with buttons/ tablets/objects etc. and will be projected on the projection surface making it into once video. The mix media content including 2D animation/Motion Graphics/3D animation and models with archival footages/animated images wherever required as according to script and storyline. The content to include green screen shoot with minimum actors to depict the different activities performed by Indians of the struggles and challenges faced by them in different scenarios of administrative, economical, agricultural, social and religious contexts. The content to be supported with voiceover in 2 languages and appropriate sound design as per the theme and effect of the installation. The audio output will be heard in the respective area only, and will be supported by multiple headphones too. The visual language has to be derived from the lithographs, paintings and artforms as approved by the design consultant. Ambient soundscape suitable with the visual content to be developed. All sound processing, dubbing, mixing, etc. costs are includes in the cost. The cost for any resources such as director, editor, music composers, singers, artists, sound engineers, recording studio charges, etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size.

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 240 sq. mm. A2XFY

NS VR - Development of interactive virtual reality content which will allow the visitors to visit the original surroundings of the time and place where the causes of oppressions by the British were being practiced in the administrative context in virtual reality using VR headsets. 3D reconstruction of a court room where the Indian is being tried and given life sentence for stealing bread and no one is there to present the case of the Indian to protect him. the 3D construction will be done in game engines like Unity/Unreal. The VR interface should allow the user to choose the instrument using gaze control. Each setup will have minimum 5 interactive points with 2 min of playtime experience, that will reveal information in form of text/images/video about the instrument. The voice over/subtitles for the film will be done in 2 languages - Hindi and English. The rate to include all research, 3D modelling, required photo/video shoots, rendering, vfx etc required for the complete experience of the virtual tours. All necessary photoshoot and video shoot to be included in the cost. The cost for any resources such as actors, costume, script, director, cameraman, music director, composer etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size. Please refer video no.

NS Hologram - Audio visual clips of total 3 - 5 minutes duration with multiple Indian people are facing the oppression of the British in the context to the religious oppression . The av will capture the tough battles faced by the British forces to fight the revolutionaries. The footage needs to be treated as per the technical requirement for the holographic projection system for best effect. The voice over/subtitles for the film will be done in 2 languages - Hindi and English. The rate to include all research, 3D modelling, required photo/video shoots, rendering, vfx etc required for the complete experience of the virtual tours. All necessary photoshoot and video shoot to be included in the cost. The cost for any resources such as actors, costume, script, director, cameraman, music director, composer etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size.

NS Peep Hole - Montage film of 30- 60 seconds depicting the images of all the different oppressions done by the British in various villages and area e.g. the doctrine of lapse, the annexation of different regions, battle of pallasey etc. the peep hols will showcase the documents, images, paintings and lithographs etc to highlight these oppressions in different regions of India. The rate to include required 2D animation, motion graphics, copy for subtitles, appropriate background music (if any).

NS Projection show - The AV on the curved screen explains the planning of the first freedom struggle across the country. The film explores the evidences of the planning happening across different regions and people of those regions i.e. the soldiers, the noble, the common man and the modes of their communication. the AV will highlight the symbols of this freedom struggle and their relevance. The AV will contain mixed media content including 2D animation/Motion Graphics/3D animation and models with Live action shoot wherever required as according to script and storyline. The content should be supported by sound design and Voiceover in 2 languages of duration 5-7 minutes.

NS Greased cartridge Hologram - The greased cartridge will be hologram projection show with Green screen shoot, editing and processing of 3-5 minutes where the visitors will understand the parts of the Enfield rifle and where and how the greased cartridges were supposed to be used by the people operating the machinery. this will highlight the elements of these the cartridge as different parts will disintegrate with the help of motors and the projection on the gun and the screen behind will highlight the effect of use of the fat from the cow and pig hurt the religious sentiments of the people of the country. the show will run in loop. The film to include minimum of 2 actors to showcase the use of the gun dressed as soldiers/ villager/british official, motion graphics, 2D/3D animation, information graphics, images, video content, illustrations, sketches that will be created or procured from archival content. The rate to include all 3D modelling, required photo/video shoots, rendering, vfx etc required for the complete experience of the virtual tours. All necessary photoshoot and video shoot to be included in the cost. The cost for any resources such as actors, costume, script, director, cameraman, music director, composer etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size. Please refer video no.

NS Ambala location instalation table of the map of ambala made of corian/ bronze/ mdf/ acrylic/ concrete with AR pods (Min.8 no.s) through which the visitor can interact with the Ambala map. - The AV focusses to explain the strategical location and topographical representation of Ambala and nearby area with special focus on its connectivity to Delhi, North West Frontier Province and Shimla (the summer capital of the British during 1857) and explain the importance of British setting up the cantonment area in Ambala. Since the film is a mix media installation combining kinetic surfaces with projection the visuals will be graphical highlighting the various regions of northern part of India and details of Ambala region and the surface of the screen. The duration of the AV will be 5-7 minutes with VO in 2 languages. The film to include motion graphics, 2D/3D animation, information graphics, images, video content, illustrations, sketches that will be created or procured from archival content. The movement of the kinetic blocks also to be designed in synchronisation with the AV to create the design effect as per the approval of the Museum design consultant.

NS SAFETY EQUIPMENT (Electrical & UPS Room only - H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

NS 3d projection mapping - The AV will be a curated projection mapping show of 6-8 minutes explaining the break out of events in Ambala city at various locations. The projection mapping will be done on scaled models of the buildings/monuments/ landmarks/residence buildings of the war over these buildings with holograms, dmx controlled lighting on the debris /parts of the buildings made. Intended to project dynamic imagery onto the model blocks, transforming the lifeless physical model into a visually appealing and almost real life fire outbreak around and realistic experience. Since the audio visual will be visible on the models, the AV will should be developed to make the most of the visible area to enhance the viewer's experience. The AV will contain mixed media content including 2D animation/Motion Graphics/3D animation and models with Live action shoot wherever required as according to script and storyline. The content should be supported by sound design and Voiceover in 2 languages of duration of 6-8 minutes

NS Ambala letter installation with interactive morse code tables - The 2-3 minute projection on the table show exhibits the telegram which proves that the freedom struggle in Ambala happened few hour earlier than any other city. the table will be exhibited in the scenography that sets the context of the telegraph office with multiple interactions on multiple tables. The main table will have the projection of the telegram being decoded from the electrical signals into text as per the original telegram. this projection will be supported by ambient sound which will resemble the sounds of the electrical signals. these signals will also be a play of light visible as a beams of light running through various electric wires in the scenography. The AV should be developed as per the setting of a telegraph office table where statues/mannequins/ models of suitable personnel and officers are physical seated around the table on the physically present chairs and decoding the signals being received at the office. the other interactive tables will be setup along with the morse code/telegraphic signals generating equipment’s supported by an audio visual of various telegrams on the tables/walls/projection screens etc. The visuals will include motion graphics, videos/images from archives, illustrations, 2D/3D animation etc in Full HD/appropriate resolution along with suitable sound design developed as per requirement.

NS Printing of Museum Tickets of 1000 copies as approved by musuem consultant.the quality material, color etc of the final product should be exactly same as per the sample approved after the desigining phase.

NS Scenic diorama and projection - AV of duration 5-7 minutes will be projected on 2D/3D surfaces depicting 4-8 scenes/ stories and events of the war and battles that occurred between the Indian freedom fighters and the British forces in Ambala during the months of May 1857 to June 1857. The audio visual will be a journey of major events on 10th May 1857 during the entire day at various locaations in Ambala i.e. the old church, the new church, British bunglows etc. followed by the freedom struggle till June 1857. The Av will be a glimpse into these dramatic encounters between the two forces and the visitors will feel as if they the incidents are happening in front of them giving them an immersive experience.The film will be screened on surfaces and dioramas etc. along with DMX controlled lighting and immersive effects to give the visitors an experience of the battle field and using motion graphic, 2D/3D animation, imagery and video content supported with voiceover In 2 language and supported with appropriate sound design explaining. The data will be a recreation of war glimpses, movements of army, transportation provisions and people in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval with best projection effect along with required ambient sound.

NS Haryana map installation displaying 2D/3D map model of haryana with projection over the map surface and pods on it displaying minature models related to the place/event - The AV of duration 3-4 minutes being played in a loop showcases the spread of the freedom struggle from Ambala to the different regions of Haryana. The projection on the 2D/3D map of Haryana will highlight the different regions of Haryana including the major freedom struggle centres, villages, locations, movement of the revolutionaries, movement of the British armies and the routes taken by all. These projections will also highlight the terrain, rivers and road connectivity of the major centres of Haryana to neighbouring regions such as Delhi, Meerut, North west frontier province, Shimla, Rawalpindi and Lahore etc. These projections will be glimpses of the overall scenario to understand that the freedom struggle was spreading across the state like a wildfire. The content projected should be in synchronisation with the outline and terrain map created with 2D/3D elements and nearby area printed on the custom made vinyl across flooring and walls. The data will be a recreation of war glimpses, movements of army, transportation provisions and people in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval, along with required ambient sound.

NS Bridge platform with for interactive screen - The Ramp to observe the Haryana map and its projection will also have several touch screens with multiple interactions to explain the details of the map. the details will include the name of the area, its district, surrounding regions, number of , dates, people involved i.e. the noble, villagers and British officers etc. the touch interactions will give a glimpse of the relevance of hat region/area/ village etc and its overall context but the content will not be an in-depth details about the freedom struggle. there will be minimum 5 interaction options for the visitor in each touch screen with further interaction options if required integrated with the application and sound. The application will have approximately 10 pages for which wireframing, user interface design , front end and back end coding of the user interface will need to be developed as per the approval of the design consultant, he visuals will need to be defined accordingly. Development of mixed media content (using 2D animation/Motion Graphics/3D animation where ever required as according to script and storyline) of duration 30-60 seconds minutes wherever required. The content should be supported by sound design and voice over wherever required. Programming using HTML/Unity/Java or any other interactive programming language to be considered. Related detail content identification to be done by the vendor.

NS Projections with models/building depicting scenes of Battles in different regions of Haryana - The multimedia exhibition interactions showcase the battle scenes across Haryana in in details in the major cities i.e. Thanesar, Rohnat, Mewat, Gurgaon, Hisar etc. The overall space includes multiple projections show the details of the places/people/villages/areas etc where the battles occurred and were fought between the freedom fighters and the British. The Av content will be developed as a projection mapping show of 2-3 minutes on and will highlight the achievements of the Indians in these battles. 2D/3D Projections will be running on the artwork screens behind and on the exhibits. the projection content will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval, along with required directional sound in two languages as per requirement.

NS Audio experience inside Homes and villages - Audio files and voiceover in the local language with required sound design converted to suit the directional speaker hardware of duration 1-2 minutes which will be played on loop. The content to be developed as per the mood of the overall gallery depicting the battle cries and the shouting and overtaking of the Indians in different regions of Haryana. The output to be planned as per directional speakers planned in the entire gallery with a sense of continuity.

NS Montage Visual Content of battle scenes - Montage film of 1-2 minutes at different locations depicting the images of all the different places where the wars and the battles happened in the regions and major monuments. The rate to include required 2D animation, motion graphics, copy for subtitles, appropriate background music (if any).

NS Activity Holograms - Green screen shoot, editing and processing of 10 audio visual clips of total 1-2 minutes duration to showcase the activities of making arms in Haveli of Rao Tula Ram. The visitor will peek in the Haveli model to see the different activites ahppeing and people interacting with each other to plan freedom struggle against the Britih. The audio visual will be developed with green screen shoot, editing and processing to highlight multiple freedom fighter/villager/local leader/ soldier/farmer etc. fighting the battles with the British forces at different locations. The av will capture the tough battles faced by the British forces to fight the revolutionaries. The footage needs to be treated as per the technical requirement for the holographic projection system for best effect. The projection content will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval, along with required directional sound in two languages wherever required.

NS Well reflection- Augmented reality - Augmented reality based face recognition interactive kiosk. The Audio visual will be created through a database of details of the freedom fighters involved in the planning of the freedom struggle. The visitor will stand looking inside the well to see the reflection of their own face which will a look a like freedom fighter and messages will appear in the well, which will be read out by the visitor and give an echo effect seeming like a passing of the message to plan the freedom struggle against the British. the entire cycle of this experience will be 3-5 minutes depending on the timing of the sensor recognizing the face and displaying the details. at least 5-10 visitors can be a part of this interactive exhibit collectively. the visual output will be a picture along with supporting text and ambient sound, the images of the visitors will be recreated by referring the archival images/paintings/lithographs/ and other documentation etc. the content should be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval.

NS Interactive Letter/ Telegram/ Document - The interactive sensor projection on the letter/telegram/ document replica or recreation will be activated by a flipping gesture on with the help of sensors and projector. It enables the visitors to go through the letters written by the British officials to their fellow officeers regarding the situations in various cities highlighting their concerns regarding the Indians taking over the cities and the British loosing controls over major regions. The letters will hihglight that the British were in a state of fear, helplessness and were intimidated by the Indian freedom fighters. The content for the projection will include motion graphics, illustrations and images along with text designed for replica or recreation of letter/telegram/ document spread in Full HD resolution, in an abstract and visually appealing layout and design manner as per the approval of the design consultant. The content to be developed according to good for coding and development.

NS LED Screens - The multiple projections (appprox 20 in nos. LED screens) will showcase the images/paintings and lithographs etc. of the freedom fighters of the first struggle. The images in the screen will also highlight the name, place, village, region and state etc. and other few personal and native details of these revolutionaries. the content on these screens will be running on loop with the images and details changing after every 30-60 seconds as per requirement. each screen will have at least 10 different variations of these leaders each being displayed for the mentioned duration. Programming using HTML/Unity/Java or any other interactive programming language to be considered. Related detail content identification to be done by the vendor.

NS Montage visual Content of battle scenes - Montage film of 1-2 minutes at 5 locations depicting the images of all the different places where the wars and the battles happened in the regions and major monuments. The rate to include required 2D animation, motion graphics, copy for subtitles, appropriate background music (if any).

NS Katputli show - Development of a mix media content with mechanical and automated katputli movement show of duration of 8-10 minutes of occurrences of battles in different regions of Haryana and the tough fight between the different people of Haryana and the British army. The entire show will highlight the major events of the Freedom Struggle in the region. Using the media of the Katputli folk culture i.e. the puppetry show which is different puppets handled by few strings for movement. puppets which will be made from wood covered with cotton cloth and tied with a metal wire which acts as a string operated by a mechanical timed motors similar to kinetic sculpture movements. the strings will be controlled by a multiple string that passes from the top of the puppet to synchronized motors. the multiple puppets of different characters will be created along with a backdrop of a stage like setup with printing on wooden panels/ fabric/ Corian etc. the show will be supported few projections on the backdrop along with dmx controlled lighting. The Projection will be mixed media content including 2D animation/Motion Graphics/3D animation and models with Live action shoot wherever required as according to script and storyline. The content should be supported by sound design and Voiceover in 2 languages.

NS Outbreak at India Installation with Model elements made of acrylic/corian/mdf, AR integrated sensor based touch devices(9' pads), Sensor based Projection over the map surface - The audio visual content development of for android/IOS devices/tablets. It lets users of these devices easily preview, place, view, and interact with physical 3D models in their environment. The 3d elements related to the battles of freedom struggle will be fixed in the scenography with India map printed on glass on floor and wall. the devices will show the 3D elements in the devices/digital screen with relevant background related to the battle, the 3d model will become live and give an output of animated moving visual e.g. the 3d element of a fort will be have visual content of a battle happening between armies in the fort, the 3d element of a horse will become line in the digital screen with an audio visual of the horse moving to different zone and running in a battle. the audio visual will be triggered as soon as the tablet/digital screen will be directed and pointed to the physical 3d element in the space for a few seconds 93-5 seconds). The content will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval, along with required sound, the sound output will be in headphones connected to the digital device. Content to be made according and suitable to the running program using HTML/Unity/Java or any other interactive programming language to be considered. Related detail content identification to be done by the vendor.

NS Holograms - Inside the replica of the Barielley jail monuments, to highlight forgotten stories of Barielley and people hologram shows will be done to show the stories of the battles fought and won by Khan Bahadur Khan and his role in the Freedom Struggle. Green screen shoot to includ minimum 2 actors to depict the mentioned theme, editing and processing of audio visual clips of total 3-5 minutes duration with multiple freedom fighter/villager/local leader/ soldier/farmer etc. fighting the battles with the British forces at different locations. The av will capture the tough battles faced by the British forces to fight the revolutionaries. The footage needs to be treated as per the technical requirement for the holographic projection system for best effect

NS India Documentary 360 degree projection - Development of a 360 immersive projection audio visual film of duration 3-5 minutes. The visitors will be seated on different elements that were a part of the battle scenes and movement during the wars e.g. horses, carts, elephants, boats etc. the projection will be done across the screen and the floor and on the visitors as well. The AV will narrate the story of spreading of the First Freedom Struggle across India and that the planning of all the battles against the British Raj was being done across the country and there were wars and battles in all major and smaller cities and more than 30 such places were covered. The show will showcase the movement of all freedom fighters towards Delhi; the power centre and the city from where the Indian King ruled, highlighting the tough battle that the British had to face for several months and the Indians managed to make major areas free even after not being military trained and the freedom fighters being the noblemen/ villagers/ farmers and the common man and celebrate the achievements. The film will have mixed media content including information graphics, illustrations, 2D animation/Motion Graphics/3D animation and models with live action shoot wherever required as per the theme and storyline of the film. The content should be supported by sound design and voiceover in 2 languages - Hindi and English. All necessary photoshoot and video shoot to be included in the cost. The film will have an original musical score to support the visuals, all sound processing, dubbing, mixing, etc. costs are included in the cost. The cost for any resources such as music composers, singers, artists, instrumentalists, sound engineers, recording studio charges, etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size. The cost for photoshoot, video shoot, documentation of the related content to be included along with the human resources and suitable equipment’s required for the shoot, drone shooting with appropriate equipment’s required to do the same.

NS Projections in models/building depicting scenes of Battles in different regions of India - The projection mapping inside and on the major monuments showcases the battle scenes in details in the different area of India at important monuments, cities along with major leaders where major battles took place across india i.e the Kashmiri gate Battle in Delhi, the Lucknow residency in Awadh, Sati Ghat in Kanpur, Kali Paltan Mandir in Meerut, will highlight their iconic elements i.e. Jhansi ki rani's horse and nan Rao's elephant, North West Frontier Province, Rohilkhand, Gond region etc.. The show will highlight the role of the fighters these projections will highlight the simultaneous battles happening at these places, the freedom struggle and the battles spread pan India in no time as the date for the freedom struggle was already fixed.. The overall space includes multiple projections show the details of the places/people/villages/areas etc where the battles occurred and were fought between the freedom fighters and the Britishers'. the projection will highlight the achievements of the Indians in these battles. 2D/3D Projections of duration 1-2 minutes will be running on the screens inside the monument exhibits with voice over and sound in 2 lauguages i.e. Hindi and English. The projection content will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval.

NS Audio Visual on screens - The audio visual wil highlight the freedom struggle and battles in other places which were not major centres of revolt but smaller cities, villages, towns etc. eg. Aurangabad, Bihar, Orrissa, Assam, Dinajpur, Ajnala, Sambhalpur etc.. The show will highlight the sequence of the battles and the role of the freedom fighters across these places and the contributions of the people of these places. It was also highlight the details of the places/people/villages/areas who supported them in this freedom struggle. the AV intents to highlight the achievements of the Indians in these battles. 2D/3D Projections of duration 1-2 minutes will be running on the projection surface related to the places. The projection content will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval, along with required directional sound in two languages.

NS Audio in other Languages - Development of audio voiceover with background music/sound and instruments forin atleast 5 most national/ international languages which would be played in audio guides at various places throughout the museum, primarily for the projection mapping show. The overall recording time will be of atleast 30 minutes with various effects and modulations along with some use of local Haryanavi artists. The cost for any resources such as local artist, music composers, artists, instrumentalists, sound engineers, recording studio charges, and all recording and sound processing charges etc. to be included in the cost. The languages will be chosen as per requirement from the client or museum design consultant.

NS Ambient music and Folklore - Development of background score/ ambient sound to be played at various places throughout the museum of 3 mins to be played on loop with various effects and modulations and are sources are with various musical instruments along with some use of local Haryanavi instruments. The ambient music will also include some nodes of human voice over for background effect i.e some taal, poetry and local folklore artists. The cost for any resources such as local artist, music composers, artists, instrumentalists, sound engineers, recording studio charges, and all recording and sound processing charges etc. to be included in the cost. The content should have original music score.

NS Audio experience inside Homes and villages - Audio files and voiceover in the local language with required sound design converted to suit the directional speaker hardware of duration 3-4 minutes which will be played on loop. The content to be developed as per the mood of the overall gallery depicting the battle cries and the shouting and overtaking of the Indians in different regions of Haryana. The output to be planned as perthe directional speakers planned in the entire gallery with a sense of continuity.

NS Tunnel experience - The interactive and immersive experience of the tunnel will be journey of the visitors from the red zone of the battles to a dark zone of atrocities. The visitors will carry the torch/digital/physical mashaal/torch that resembles the torches that the freedom fighters carried during the freedom struggle with them in the gradual elevated ramp space. When the torch/mashaal come close to different point on the wall will trigger the projection on the walls of the tunnels and on the sides to revel content giving glimpses of the Britieshers taking over the cities of India during battles, along with begining of atrocities the British did after the lost of battles in many places. Similar to a shadow projection at places it will also showcase some words related to the atrocities and supported by visuals. The output will be projections along with ambient audio. the sensor based projection will be triggered if the visitor comes close to .5m from the sensor on the wall, its an rfid/nfc interaction based content. There will be minimum 10 sensor based interaction points with projection of 10-30 seconds each. once two visitors come close to a point the projection will start again only after finishing the first loop. Content using 2D animation/Motion Graphics/3D animation, illustration, models with live action shoot wherever required as according to theme and storyline. The visual language has to be derived from the artforms, images, paintings and lithographs etc. as approved by the design consultant. Ambient soundscape suitable with the visual content to be developed as per requirement. All necessary photoshoot and video shoot to be included in the cost. The cost for any resources such as actors, costume, script, director, cameraman, music director, composer etc. required to be included in the cost. The content should be made in appropriate resolution as per screen size.

NS Sensor projections on wall surface- Projection on the wall surface- - The AV will include 10 projection films of duration 30 seconds each taking about the different battles eventually won by the British army in different parts of India. An interactive exhibit includes a physical mashaal/torch carried by the visitors that resembles the torches that the freedom fighters carried during the freedom struggle. this torch will be carried by the visitor and when touched to the wall will trigger the projection on the wooden screen/diorama/surface in front. This interactive exhibit's content will provide the visitor with cues/triggers to tap and touch the 2D/3D Diorama and the output will be the visuals of the British taking over the villages/ monuments/places etc. in the various cities in India and beginning the atrocities. There will be a multiple interaction points for one participant and multiple participants and interact with the wall. Content using 2D animation/Motion Graphics/3D animation, illustration, models with live action shoot wherever required as according to theme and storyline. The visual language has to be derived from the artforms, images, paintings and lithographs etc. as approved by the design consultant. Ambient soundscape suitable with the visual content to be developed. All necessary photoshoot and video shoot to be included in the cost. The cost for any resources such as actors, costume, script, director, cameraman, music director, composer etc. required to be included in the cost. The content should be made in appropriate resolution as per screen size. All user interface design, wireframing and user experience design and development to be includes in item rate. The Software application / CMS / Online Portal should be based on UNITY GAME ENGINE WITH UNREAL REAL TIME 3D rendering tool. and MSSQL as backend with no additional license cost and unlimited uses. Complete UI/UX, 3D Modelling and Rendering also part of the application. App flow and UI/UX will be finalise after the approval of museum Consultants. Application Software source code needs to be handover in a hardisk. Bidder will be responsible for providing User Training, User Manuals for all types of users (including Administrator role) and Technical Documents. (Softcopy should be digitally signed by project manager of the vendor). User Experience should be easy and impactful.

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3C x 6 sq. mm. 2XWY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3C x 10 sq. mm. 2XWY

NS India Documentary Atrocities - Development of a curved projection audio visual film of duration 3-5 minutes narrating the story of the consequences of the battles and the freedom struggle giving glimpses of episodes of aftermath, atrocities, loot, plinder, punishments and deportations etc.. The Av will highlight the aftermath atmosphere of the freedom struggle and describes the post-war terror spread by the British occupation, it will showcase the movement of the British forces across major regions and the capture of leaders, villagers, common man. It will also highlight the lootings done by the British and the propoerties were being confisticated and destroyed by them. The film will have mixed media content including information graphics, illustrations, 2D animation/Motion Graphics/3D animation and models with live action shoot wherever required as per the theme and storyline of the film. The content should be supported by sound design and voiceover in 2 languages - Hindi and English. All necessary photoshoot and video shoot to be included in the cost. The film will have an original musical score to support the visuals, all sound processing, dubbing, mixing, etc. costs are included in the cost. The cost for any resources such as music composers, singers, artists, instrumentalists, sound engineers, recording studio charges, etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size. The cost for photoshoot, video shoot, documentation of the related content to be included along with the human resources and suitable equipment’s required for the shoot, drone shooting with appropriate equipment’s required to do the same.

NS Haryana Documentary Atrocities - Development of audio visual film of duration 3-5 minutes reciting the atrocities executed by the British in various cities, towns, villages and battle locations of Haryana. The British after taking over the capital of the country indulged in mass killings of the Indian freedom fighters, leasrds, villagers etc. The AV will also highlight the views of these cities and showcase the damages caused in these areas, and the fact that the fellow countrymen were left hopeless with the actions of the foreigners.The film will have mixed media content including information graphics, illustrations, 2D animation/Motion Graphics/3D animation and models with live action shoot wherever required as per the theme and storyline of the film. The content should be supported by sound design and voiceover in 2 languages - Hindi and English. All necessary photoshoot and video shoot to be included in the cost. The film will have an original musical score to support the visuals, all sound processing, dubbing, mixing, etc. costs are included in the cost. The cost for any resources such as music composers, singers, artists, instrumentalists, sound engineers, recording studio charges, etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size. The cost for photoshoot, video shoot, documentation of the related content to be included along with the human resources and suitable equipment’s required for the shoot, drone shooting with appropriate equipment’s required to do the same.

NS Projections with models/building depicting the scene of destruction /atrocities across india - The projection mapping inside and on the major monuments showcases the aftermath atmosphere of the freedom struggle and describes the post-war terror spread by the British occupation. The AV describes the details of the places/people and system that the British overtook after winning the battles in the different parts of the country. The atrocity scenes in details in the different area of India at important monuments, cities along with major leaders where major battles took place across india i.e the Kashmiri gate Battle in Delhi, the Lucknow residency in Awadh, Sati Ghat in Kanpur, Kali Paltan Mandir in Meerut, will highlight their iconic elements i.e. Jhansi ki rani's horse and nan Rao's elephant, North West Frontier Province, Rohilkhand, Gond region etc.. Projections of duration 1-2 minutes will be runningin loop inside replicas of different buildings/monuments showing a continuous stream of original images/footages taken by the British photographers post the battles, 1858 onwards along with clippings of newspapers published in different countries regarding the happenings in India. the content will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval, along with required ambient sound.

NS Visual Content for building destruction on screens - Montage film of 1-2 minutes depicting the destruction caused after the British took over the power centre of the country i.e. the Red Fort in Delhi and other important monuments across India, with moving and still images. The video will be made using archival images, documents and footages showing the conditions immediately after the Kashmiri gate battle, in red Fort Delhi and around the country. The rate to include required 2D animation, motion graphics, copy for subtitles, appropriate background music (if any).

NS Hologram - Holographic projection of duration 2-3 minutes showcasing the scene of atrocities being committed by the British on the freedom fighters of India, mix media content including 2D animation/Motion Graphics/3D animation and models with archival footages wherever required as according to script and storyline. The content to include green screen shoot with minimum 2 actors to depict the execution scene carried out by a British official on a villager and other people looking in the backgground. The content will run on loop and to be supported with voiceover in atkleast 2 languages and appropriate sound design as per the theme and effect of the installation. The rate to include all 3D modelling, required photo/video shoots, rendering, vfx etc required for the complete experience of the virtual tours. All necessary photoshoot and video shoot to be included in the cost. The cost for any resources such as actors, costume, script, director, cameraman, music director, composer etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size. Please refer video no.

NS Audio experience inside Homes and villages - Audio files and voiceover in the local language with required sound design converted to suit the directional speaker hardware of duration 5-7 minutes which will be played on loop. The content to be developed as per the mood of the overall gallery depicting the aftermath of the killings of the loved ones, family, friends, leaders and fellow freedom fighters with the sound like gun shot being fired, sword being struck, bodies being hanged, destruction happening to infrastructure, voices of people running creating a sense of chaos, fear and pain. The output to be planned as per directional speakers planned in the entire gallery with a sense of continuity.

NS Before after Interactive model Tables- Red Fort, Delhi and other major cities - Many important monuments and places were completely damaged and 90 percent destroyed by the British, some buildings are not even traceable today. After the destruction of these monuments, the British barracks were built across the country at major centres. Interaction points on a table will be provided with physical scale models of different elements of the red fort, as soon as the visitor touches the model, it will disappear on the main projection screen in front and will be replaces by an appearance of a British structure in its place. it will highlight that the physical model in front of the visitors changes into the post 1857 struggle where the place will look completely different as appearing on the projected screen. The projected content will be mixed media Content using 2D animation/Motion Graphics/3D animation, illustration, models with live action shoot wherever required as according to theme and storyline. The visual language has to be derived from one of the Haryana based handicrafts such as block printing etc as approved by the design consultant. Ambient soundscape suitable with the visual content to be developed. There will be minimum of 8 interaction options for the visitor including input from the tablets/touch screens, 8 sliders, push buttons. The visuals will need to be defined accordingly. The projection will include a minimum of 2 major areas i.e. the Red Fort Delhi and Hussainabad in Lucknow.

NS Atrocities tree - The immersive audio visual projection content of 3-5 minutesto be developed in minimal and shadow projection like format to evoke the maximum emotions. the projection will be done on the screen running across the walls of the gallery having the physical tree installtion in the center of the gallery. The Tree is the visual symbol in the museum since 1857 and after more than 150 years of the first freedom struggle. India was a very prosperous country before the British took over the country and the eventually the tree was used as a medium of atrocities on the Indian population and numerous bodies were hanged on these trees and left to die. these hangings on trees happened in every city. Hence there is a central installation with a tree in the centre and a projection show on the circular walls of the space with evocative shadow projections and an ambient sound to create another dimensionality to the space. the sound of blood drops falling in the pool of liquid to create a resonating effect. the projection content will be running on loop will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval, along with required ambient sound.

NS Multimedia audio visual - A central installation in the room comprising of various video screens will be showcasing the Haryana of today and celebrating its achievements and success stories. 5 Audio Visuals of 1 minute each celebrating Harayana as an industrial and agricultuiral hub will showcase stories running on these various digital screens these different mediums also showcase the transformation of the technology. The content will be running on loop will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval, along with required ambient sound. Archival footages for the creation of AV's will be used wherever required and available.

NS Sensor projection and interactions - The interactive audio visual in the gallery showcases the aftermath of the country and its attainment of freedom from the British rule over a period of 90 years in 1947. The immersive experience to showcase the history of the country from year 1857-1947 in the gallery. The audio visual will be and immersive projection of the abstract Indian Flag in the entire space running continuously and when the vistor comes close to the projection screen within a 1 meter proximity, a sensor will triggered and change and reveal another content related to the events that contributed to the freedom of the Country. Minimum 10 such historical events will be revelaed in the audio visuals. The AV of 1-2 minutes will be running on loop in the background only to be revelaed with proximity sensor interaction and will be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval, along with required ambient sound. Archival footages for the creation of AV's will be used wherever required and available.

NS AR Magic Mirror - Augmented reality based face recognition interactive kiosk. The Audio visual will be created through a database of details of the freedom fighters involved in the freedom struggle of the country. The visitor will stand in front of the reflecting mirror like kiosk to see the reflection of their own face which will be then matched with the facial features of a look a like freedom fighter followed by the details of those personalities e.g. name, place of birth, role in freedom struggle and the cause of their death if martyred. the entire cycle of this experience will be 3-5 minutes depending on the timing of the sensor recognizing the face and displaying the details. the visual output will be a picture along with supporting text and ambient sound, the images of the freedom fighters will be recreated by referring the archival images/paintings/lithographs/ and other documentation etc. the content should be created in full HD resolution along with 2D/3D animation, motion graphics, illustrations as per the design consultant approval.

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 4C x 6 sq. mm. 2XWY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 4C x 10 sq. mm. 2XWY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 50 sq. mm. A2XFY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 70 sq. mm. A2XFY

NS Revolutionary AV in Breakout spaces - The AV will include projection film of duration 30-60 seconds talking about the visitor journey at different intervals in the museum in the breakout spaces. The content will run on screens, with famous Haryana personalities as virtual guides, the output will be a video appearing in the screen in front of the visitor with two headphones for sound output in different laguages as per requirement with each screen. Content using 2D animation/Motion Graphics/3D animation, illustration, modelling wherever required as according to theme and storyline. All sound processing, dubbing, mixing, etc. costs are includes in the cost. The cost for any resources such as music composers, singers, artists, instrumentalists, sound engineers, recording studio charges, etc. required to be included in the cost. The content should have original music score. User Experience should be easy and impactful.

NS Development of 2D Graphics - Human resources required for development of world-class 2D/3D graphics for printing on all surfaces including glass, fabric, vinyl, concrete, MDF or any other tactile surface being used in the museum including layout design, typography, test files, illustration development, visualisation, colour schemes and print ready files for execution of a printed surface of approximately 2500 square meters. This will include graphics for scenography, environmental graphics, information panels and all other purposes. Expert designers & visualizers to be considered for graphical visualization using contemporary design language in sync with the content theme of the museum. Rate inclusive of file sampling, editing and incorporation of all changes in proof reading stages of the content in 2 languages. The cost for this will be atleast 1.00% of the overall museum cost.

NS Quiz application - Development of quiz application on the 1857 freedom struglle across India The application will have approximately 10 pages for which wireframing, user interface design, front end and back end coding of the user interface will need to be developed as per the approval of the design consultant. All necessary photoshoot and videoshoot to be included in the cost.The cost for any resources such as music composers, singers, artists, instrumentalists, sound engineers, recording studio charges,etc. required to be included in the cost.Related detail content identification to be done by the vendor. The content should have original music score. All user interface design, wireframing and user experience design and developement to be inclused in item rate. Complete UI/UX, 3D Modeling and Rendering also part of the application. App flow and UI/UX will be finalise after the approval of museum Consultants. User Experience should be easy and impactful.

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 25 sq. mm. A2XFY

NS - The AV will include 3D projection mapping film of duration 15-20 minutes about the story of the First Freedom Struggle of India in one of the first planned freedom struggle against the foreign oppressors. the show will highlight the thought battle that the British had to face for several months and the Indians managed to make major areas free even after not being military trained and the freedom fighters being the noblemen/ villagers/ farmers and the common man. the show will highlight their achievements, contributions and pay a tribute to these great leaders. The audio visual will begin with the story of Haryana, leading to the details about 1857, the first war of independence against the 200 year old rule of the British and its inception and begining in Ambala. The audio visual show how the spark of this freedom struggle spread across Haryana and then the entire country culminating to wars and battles across the country. it will highlight the tough battle that the people of the country gave to the British which frightened them. it will showcase that the country came together and united to fight the foreigners, people from various cultural, religous, economical and financial etc. background, the rulers, leaders, villagers, common man all came together and fought as one entity. Eventually even after the first freedom struggle did not give the desired results, the country did not give up and after 90 years yet again in 1947, the British had to taste defeat and leave the country and hence the country got the Independence. The audio visual will also highlight the achivements of Haryana as a state and its progress with time, the various regions of Haryana blooming in different sectors of agriculture, craft and modern day technology and city development. The AV will contain mixed media content including 2D animation/Motion Graphics/3D animation and models with Live action shoot wherever required as according to script and storyline. The content should be supported by sound design and voiceover in 2 languages - English and Hindi. The cost for any resources such as director, editor, music composers, singers, artists, instrumentalists, sound engineers, recording studio charges, etc. required to be included in the cost. The content should have original music score. The content should be made in appropriate resolution as per screen size.

NS Script Writing, Copy Writing, Copy Editing and proofreading - The team for the Script Writing, Copy Writing, Copy Editing and proofreading to come on board with required expertise and experience in similar works. The team will be of atleast 5-10 members dedicated to the project. The team will be responsible for all creative writing requirement in the museum. Copy Writing and Script Writing will include understanding the content provided by the research team to the museum execution agency, analysing it and formulating the required story for the film/panel/other static and digital mediums in required langauages. Copy Editing will include formaulating the written data in the required word / time limit for the film/panel/other static and digital mediums in required langauages. The content writing will include translation and transliteration of text materials. Proof reading is the final draft of a document to find and fix errors related to grammar, punctuation, spelling, capitalization, and formatting. Panel text, all scripts for films, application content, museum nomeclature, branding, any print media content, website content, song creation, script for artist and ushers are all included in the scope of work. Scripts may include songs, chants, folklore and poems, etc. This will include all the required Draft version and revisions till the content/ script/ text reaches the final stage of good for execution. This will include the vetting of content by the expertise providing the research. Human resources required for script writing, copywriting, copyediting and a minimum of 3-4 rounds of proofreading in each required language i.e. English and Hindi for the films and panel text for the entire museum. Atleast 3-4 revisions of the scripts and text will be written and approved by the museum design consultant. The text for the static content will include everything as per requirement e.g Museum and gallery nomenclature, panel heading, body text, image captions, credits, signages, subtitles etc. but not limited to this. Everything in written format to exhibited in the museum or to acoompany the musuem experience in any physical or virtual format will be a part of the scope of work for complete and seamless tonality and experience.The cost for this will be atleast 1.25% of the overall museum cost.

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 120 sq. mm. A2XFY

NS S.I.T.C. 1100Volts grade cable as per I S: 7098, pt.1(latest edition) with stranded Aluminium / copper conductor; XLPE insulated, multi-core, bunched, armoured/un-armoured with overall heat resistant type ST-2 PVC insulation / Copper stranded conductor; PVC insulated as per I S: 1554 (latest edition) armoured/un-armoured with overall heat resistant type ST-2 PVC insulation on surface / underground / in Pipes / trenches including the cost of digging, sand cushioning with laying etc and refillinig the same in layers or by supporting them in walls and all other accessories as required. Cable shall have nominal identification plates at booth ends ('supply from' & ;supply to'). The sizes are as follows: - : 3.5C x 150 sq. mm. A2XFY

NS Art Direction Team - The Art Directoion team will be a professional team who is in charge of developing and maintaining the creative vision planned by the design consultant for museum experience and visitors. To accomplish this, they manage teams of artists who work on creatives such as audio visuals, film, graphic design, finishes, scenography and overall essence of the space.The resources should be well versed with theme and content in relation to the museum narrative. They will be responsible for coordinating with subject experts with the required knowledge for conducting interviews, making models, artefact replicas, 2D/3D models, illustrations, graphics for display at various galleries amongst others. The resource will guide and overview the team in executing scenography, artwork and installations with respect to all tangible and intangible elements of the museum. Following are the roles and responsibilies of the Art Direction team but not limited to: - • Generate clear ideas and concepts along with the scriptwriters, copywriters and storytellers • Determine how best to represent a concept visually • Develop the overall look or style of the museum experience and space • Develop the overall theme and details of all static and digital story telling mediums • Understand the theme, evaluate and develop digital content details • Evaluating detailed script, Identifying locations, developing story boards, scenes etc. for all audio visuals in the museum expereince. • Present completed ideas to clients/team members • Determine which photographs, art, or other design elements to use • Identifying and working with actors, voice artists, director, technical production engineers and sound engineers etc. for developing digital and moving content in the museum. • Supervise art direction and scenography and set artist and team. • Supervise the actors, ushers and guides for giving tours to the visitors in the museum • Define the scripts of the actors involved in the museum storytelling and exhibits • Understand user interaction and experience. • Understand user/vistior behaviour and plan the gallery space, duration and interactions accordingly. • Oversee the fabrication, construction and execution of exhibition components • Review all detail shop drawings, artwork, photography, and graphics etc. • Produce sketches, storyboards, roughs to visualize ideas • Coordinate activities with other artistic or creative departments • Cooperate with the rest of the creative team across different types of media - • Managing, evaluating and achieving the best utilization of space, exhibition elements and other static and digital story telling tools, equipments and mediums. • Take work from detailed design to final execution within deadlines • Manage and delegate responsibilities to other artists and provide directions • Maintain the planned intent of the Museum. - The Art direction team will be overall responsible to excute all the creative detailing and management tasks related to museum and experience design at the 1857 Museum and Memorial. The overall quality of international standards will be achieved in all aspects and no compromise on any conditions shall be done. This team will be accountable for syncing all teams, communicating with museum design consultants, works, managing, coordination and overlooking services as per design, on time development, fabrication, execution, quality and experience at all times. Human resourses and team of atelast 10 people should be dedicated to the project with required expertise and experience in similar works/fileds/projects of museums and scenography, MOU with an expert agency to be done with for the same as required. Atleast 3-4 revisions of the concept detailing/ visualization/ drawings and details will be done as per requirement and approval by the museum design consultant. The cost for this will be atleast 1.25% of the overall museum cost.

NS UI UX for all interactions - The application to include all necessary hardware, software and servers to be included. Programming using HTML/Unity/Java or any other interactive programming language to be considered. The content should be supported by sound design and voiceover in 2 languages - Hindi and English. The Software application / CMS / Online Portal should be based on UNITY GAME ENGINE WITH UNREAL REAL TIME 3D rendering tool. and MSSQL as backend with no additional license cost and unlimited uses. Complete UI/UX, 3D Modeling and Rendering also part of the application. App flow and UI/UX will be finalise after the approval of museum Consultants. Application Software source code needs to be handover in a hardisk. Bidder will be responsible for providing User Training, User Manuals for all types of users (including Administrator role) and Technical Documents. (Softcopy should be digitally signed by project manager of the vendor). User Experience should be easy and impactful. The cost for this will be atleast 0.25% of the overall museum cost.

NS UPS SYSTEM- S.I.T.C. natural / forced air-cooled, ON-LINE UPS suitable to operate in 'Hot Standby' or 'Parallel' or 'Stand-alone' mode, work at 45° C temperature and relative humidity of 95% with IGBT technology complete with battery bank for 15 - 20 minutes back-up as under: : In-put power supply : 415V (+ 10% - 15%), 50Hz (± 3%), 3 phase. : Output power supply : 415V (± 1%), 3 phase, 50Hz (± 0.5%) : Pure sinusoidal waveform : Overload capacity of 110% for 15minutes : Out-put regulation shall be ± 2% against input and load variation. : Protected against output overload, DC input, Low/over input voltage, : Battery pre-exhaust alarm at-least two minutes before ‘DC Low’ tripping. : Open Battery Rack & Interlinks : Capacity of the UPS shall be 100KVA

NS Ceiling - ‘Aphony Gloss Seamless panel’ tiles 15 mm on Wooden Studs. Providing and Fixing of ‘Aphony Gloss Seamless panel’ tiles 15 mm thick with square edge made of Gloss base panel with Wood Fibre 1mm width cement composites covered with AcousticallyTransparent Absorptive printed microfibers on the front side pasted on site with sprayableglue as per the choice of the Architect/ person in charge of size 1200X1200 mm withseamless finish. Has excellent noise absorption of 0.90 NRC as per ISO: 354-1985 andASTM 423-90 a, STC of 47 as per ASTM E90/413 for 25mm, Density 400 Kg/ m3, meetsstringent Fire Ratings ASTM D- 876 and BS:476 , weather resistance as per IS 3308,Thermal Insulation as per IS:3346-1980 with relative humidity of 90% RH at 60o Celcius(140oFarenhite) for 15 days= No deterioration.Conforms to En 131682001 and are RoHSComplaint. Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results Anti Bacterial test as per JIS-Z2801-2010.To be installed on Engineered Wooden Stud 47X47 mm system with a backing of Himalayan Acoustics 50mm 1000 Gsm thick absorb wool tested as per fire retardant ASTMD 635-1991 abd 15061-2002 for excellent results. ( AOR No.RA-01 )

NS WALLS Partition Wall - ‘Sound barrier seamless’ tiles 25 mm Providing and Fixing of ‘Sound barrier seamless’ tiles 25 mm thick with Wood Fibre 1mm width cement composites covered with Acoustically Transparent Absorptive microfibers on the front side pasted on site with sprayable glue as per the choice of the Architect/ person in charge of size 600x1200mm with seamless finish having an NRC 0.60 and STC of 30 on both side. The panels is made of a combination of medium and high density wood fibre cement thus having an overall density of 650 kg/ m3. The joints at the Isolated side of the panel are to be sealed with weather proof Epoxy sealant to avoid any sound leakage. To be installed on MS Frame Work to be provided by Clients with a backing of Himalayan Acoustics 2X50mm 1000 Gsm thick absorb wool tested as per fire retardant ASTMD 635-1991 abd 15061-2002 for excellent results. ( AOR No.RA-02 )

NS WALLS Brick Walls - ‘Aphony Gloss Seamless panel’ tiles 25 mm. Providing and Fixing of ‘Aphony Gloss Seamless panel’ tiles 25 mm thick with square edge made of Gloss base panel with Wood Fibre 1mm width cement composites covered with AcousticallyTransparent Absorptive printed microfibers on the front side pasted on site with sprayableglue as per the choice of the Architect/ person in charge of size 1200X1200 mm withseamless finish. Has excellent noise absorption of 0.74 (for base panel) as per ISO: 354-1985 and ASTM 423-90 a, STC of 47 as per ASTM E90/413 for 25mm, Density 400 Kg/ m3, meets stringent and BS:476 , weather resistance as per IS 3308, Thermal Insulation as per IS:3346-1980 with relative humidity of 90% RH at 60o Celsius (140o Fahrenheit) for 15 days= No deterioration. Conforms to En 131682001 and are RoHS Complaint Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results Anti Bacterial test as per JIS-Z2801-2010. To be installed on Brick Wall on Ply Strips. ( AOR No.RA-03 )

NS CEILING Baffle Ceiling - Aphony Gloss Baffle 25 mm Providing and Fixing ‘APHONY GLOSS BAFFLE’ made of Wood Fibre cement composites covered with Acoustically Transparent Absorptive microfibres on the front side 25 mm thick with an option of colours as per the choice of the Architect/ person in charge of any size. Has excellent noise absorption of 0.74 (for base panel) as per ISO: 354-1985 and ASTM 423-90 a, STC of 47 as per ASTM E90/413 for 25mm, Density 400 Kg/ m3, meets stringent Fire Ratings ASTM D- 876 and BS:476 , weather resistance as per IS 3308, Thermal Insulation as per IS:3346-1980 with relative humidity of 90% RH at 60o Celsius (140o Fahrenheit) for 15 days= No deterioration. Conforms to En 131682001 and are RoHS Complaint. To be installed with 6mm rod/wire. ( AOR No.RA-04 )

NS SILENT ROOM WALLS (Double Layer) & CEILING - ‘Sound dampner’ tiles 12 mm, iso Board 10mm on Wooden Studs with infill of 1000 GSM Absorb wool. Supplying and Fixing of ‘Sound dampner’ tiles 12 mm thick made of 10 mm compressed wood fiber cemet composite 1250Kg/m3 and 2mm dampner sheet.ISO Board in the thickness of 10mm, made of compressed wood particle cement composite 1250 kg/m3 provided STC 34 (Directly) and STC 38 for full system as per IS: 9901 (PART-III)-1981, DIN: 52210, PART VI- 1989, ISO: 10140 (PART-II)/ASTM-E-90 mechanically screwed on all the partition walls and ceiling with joints properly sealed with epoxy acoustic sealant to avoid any sound leakage. To be installed on upper side of Engineered wooden stud.with Iso board on other side.To be installed on Engineered Wooden Stud 47X47 mm system with a backing of Himalayan Acoustics 50mm 1000 Gsm thick absorb wool tested as per fire retardant ASTMD 635-1991 abd 15061-2002 for excellent results. ( AOR No.RA-05 )

NS SILENT ROOM WALLS - ‘Aphony Gloss Seamless panel’ tiles 50mm. Providing and Fixing of ‘Aphony Gloss Seamless panel’ tiles 50 mm thick with square edge made of Gloss base panel with Wood Fibre 1mm width cement composites covered with AcousticallyTransparent Absorptive printed microfibers on the front side pasted on site with sprayableglue as per the choice of the Architect/ person in charge of size 1200X1200 mm withseamless finish. Has excellent noise absorption of 0.90 (for base panel) as per ISO: 354-1985 and ASTM 423-90 a, STC of 47 as per ASTM E90/413 for 25mm, Density 400 Kg/ m3, meets stringent weather resistance as per IS 3308, Thermal Insulation as per IS:3346-1980 with relative humidity of 90% RH at 60o Celsius (140o Fahrenheit) for 15 days= No deterioration. Conforms to En 131682001 and are RoHS Complaint Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results Anti Bacterial test as per JIS-Z2801-2010. To be installed on Brick Wall on Ply Strips. To be installed on Brick Wall on Ply Strips. ( AOR No.RA-06 )

NS ACOUSTIC DOORS 34 Doors - Supplying and Fixing of Acoustic Door of 55 mm having an STC rating upto 53@ 1.6 k Hz as per ISO:140/ASTM90/413. The Door will be filled with high acoustic materials of 2 layers of 8 mm Water Proof Acoustic Ply with Dampner Sheet, 2 Layers of 10mm thick Absorb Wool 300 GSM, Sound Dampner 12mm 1218x1218 mm made of 10 mm compressed wood cement composites 1250Kg/m3 and 2mm dampner sheet 37 STC as per ISO 140 ( partIII) - 1995. Final Finish with Teak Ply 4mm thick interior and Exterior Side. Door frame will be made of teak wood (Sudan Teak)/ Enigineered Wood. Frame on all four sides or three sides frame and drop seal below will be provided along with the door. High load bearing hinges will be provided along. Fire resistant for 120 min as per IS 36 (4 Part -II) & (Part 20 & 22).. ( AOR No.RA-07 )

NS Museum Director - Operations & Management - Role and Responsibility: Managing the whole museum complex by coordinating with the Human resource appointed under him for operation & maintenance. They are also responsible for overseeing administrative,marketing and PR tasks and functioning of the Museum. The museum director is responsible for the daily operations of the museum as per the authority guidelines, for long-term planning, policies, any research conducted within the museum, and for the museum's fiscal health. He will overlook event management, exhibition planning and execution, strategy making for maximising museum reach, advertising, content creation and marketing. He will be responsible for setting up long term & short term museum targets and periodically evaluating the performance of the human recourses deployed at the museum. He will be responsibble for organizing training for the development for the workers on regular basis. Attend Authority meetings and get approvals on all expenditures and investments of the museum.Will be one and last point of contact to lead the over all musuem for indoors and outdoors as well. Experience: He should have minimum 10 years experience in managing museums/cultural centers/similar organsations - He should strategise on make museum run and get the maximum returns by ticket sales , rentals , our door concerts and exhibitions , indoor concerts , cafeteria and the shop - should manage of over all funds to be given to the governemt and strategise possible expenditures like housekeeping , promotional events to keep the musuem running . Qualification- Bachelors in Hotel Management/ Facility Management Masters in management/museum studies/relevant course.

NS Head Manager - Role and Responsibility: Supervising the staff appointed for the operation and maintenance of the whole museum complex and should be a single point of contact. He will be responsible for all the daily administrative and operations of the museum building. Decision making skills are vital to the position as the person will be handling customer queries and grievences on the daily basis. This includes: scheduling and overseeing all maintenance-related work by managing a team of maintenance technicians and supervisors. Ensuring that all maintenance operations are done in accordance with guidelines of the concerned authority. ensuring the facility satisfies all industry regulations. Experience -should have an experiance of management for atleast 5 years with respect to cultural spaces. Qualification- Bachelors in Hotel Management/ Facility Management Masters in management

NS Technical Staff-AV, mix media installations, digital equipment and electricals - Role and Responsibility: AV Engineer-who plays the central role in setting up, configuring, and maintaining systems such as projectors, speaker system , cameras, lighting, microphones, and control systems. Making sure all the equipments are working properly and being serviced as per the schedule.he should have experiance in handeling and operating all the hardware equipments. Experience -should have an experiance of working in the audio visual technical field for at least 5 years. -Should have a good knowledge in all the tech. used in the museum. Qualification- Bachelors in technology with the relavent feild from nationally/internationaly renowned institute

NS Technical Staff-AV, mix media installations, digital equipment and electricals - Role and Responsibility: Duty Engineers (Electrical)-Assembling, evaluating, testing, and maintaining electrical or electronic wiring, equipment, appliances, and apparatus. Troubleshooting and repairing malfunctioning equipment, appliances, and apparatus. Constructing and fabricating parts, using hand tools and specifications. Experience -should have an experiance of working in the lighting operation and management field for at least 5 years. -Should have a good knowledge in all the tech. used in the museum. Qualification- Bachelors in technology with the relavent feild from nationally/internationaly renowned institute

NS Shop staff - Role and Responsibility: Sales person/helper responsible for packaging & maintaining shop under the assistance of the Shop manager organising sales visits. Demonstrating and presenting products. Establishing new business. Maintaining accurate records, attending trade exhibitions, conferences and meetings, reviewing sales performance, negotiating contracts and packages. Aiming to achieve monthly or annual targets. Experience -should have an experiance of working at stores/showrooms/sales office for atleast 3 years. -should have an experiance of atleast 3 years working in a renowned hospitality chain Qualification Gradate with good command over verbal Hindi & English with sale skills

NS Digital marketing team - Role and Responsibility: Photographer and Videographer - He/she should have and experience in capturing the interior spaces and architectural photography and event photography in the form of both photoes and videos.should have a good knowledge of softwares required to edit/enhance/mixing/making good quality pictures or videos. should have an understaning in capturing architectural or interior design details He/She will be available for 30 hours a week. Experience- Should have an experience of atleast 5 years Qualification- Renowned course/workshop/degree in photography/videography

NS Technical Staff-AV, mix media installations, digital equipment and electricals - Role and Responsibility: Asst Manager IT Services- managers are responsible for coordinating, planning, and leading computer-related activities in the museum. They help to determine the IT needs of an organization and are responsible for implementing computer systems to fulfill the museums information systems requirements. Running regular checks on network and data security.The person should have the knowledge and experiance in all the mapping,integration, applications and all AV softwares. Identifying and acting on opportunities to improve and update software and systems. Developing and implementing IT policy and best practice guides for the museum. Managing the Server rooms. Coordinating with the 3 rd party vendor for services etc. Experience -should have an experiance of working in the software operation and management field for at least 5 years. -Should be learned in all the softwares used in the museum related to Mapping,projection,sound and integration. Qualification- Bachelors in technology with the relavent feild from nationally/internationaly renowned institute

NS Ushers - Role and Responsibility: Appointed at different locations in Museum, to guide the visitors through the museum galleries Ushers help those in attendance at museum and events. Duties include directing people to their assigned galleries, distributing programmes, answering questions and assisting people in finding restrooms and refreshments. Assist people with disabilities. Excellent customer service skills.The cost of direction by an appropriate and experianced director of the ushers should also be included in the same.He will be responsible for training and direction of the ushers. Should be fluent in atleast hindi and english language. Experience -should have an experiance of working or managing sevral cultural events. -should have an experiance of atleast 5 years working in a renowned hospitality chain Qualification Graduates required with good command over verbal Hindi & English. Will be responsible for guiding visitors within the premises Bachelor's in mass communication/journalism/management

NS Theatre Artists/Musician - Role and Responsibility: To act in different galleries as per design requirement of the experience. The cost should include the costume & make up of the actor. .The cost of direction by an appropriate and experianced director of the ushers should also be included in the same. the artits should be having a graduation degree from a renowned institute and should have an experience in the pretaining filed of atleast 2- 5 years Experience -should have an experiance of working in the software operation and management field for at least 5 years. -Should be learned in all the softwares used in the museum related to Mapping,projection,sound and integration. Qualification Graduates from a national/international acclaimed university as per the job requirement.

NS Digital marketing team - Role and Responsibility: Graphic designer-The graphic designer will assist the senior graphic designer in implementing the formats, brand guideline into all the creative made for publishing online on various platforms. The graphic designer will also assist the marketing head in creating marketing plan with schedules and list of deliverables. He/She will be available for 30 hours a week. The resource will be responsible for updating the content on all the required digital media channels along with the web portal/website. It is mandatory to post on the social media on a daily basis. The update on the web portal/website to be made whenever there is a new event/show/activity or temporary exhibition being held at the museum premises. Graphic Designer should also be available for on site / meeting at head office atleast once in two week. Proficiency in software’s like, photoshop, illustrator, InDesign, after effect & premiere pro Exposure to animation & motion graphics (a plus) Proficiency in photo/content treatmentE An obsession with tiny details, clean design and alignment Creating story boards space visualisation coordinate with research/content team. Knowledge of materials, printing techniques and execution. Technical understanding of the materials for print media (paper, vinyl, metal, Corian etc) Good coordination skills with the vendor Knowledge of print ready files Illustrating concepts by designing examples of artwork, size, type size and style understanding layout, composition, color palette and scale. Effective time management skills and the ability to meet deadlines Experience- -2 to 3 years experience. -Experience of design and development of branding, environmental graphics, installation artworks, publications. Qualification Bachelor’s and Master's degree in graphic design, art, or similar discipline

NS Digital marketing team - Role and Responsibility: Marketing Head-The marketing head will be responsible for the strategizing, development, management and implementation of an yearly/monthly digital marketing plan for the Museum. The goal of the marketing plan should be to spread awareness about the museum based on the storyline, visitor attractions and relevance of the subjects. The plan to be creatively developed to create maximum impact in driving visitors to the museum around the year, supported with extensive footfall during the tourist season. The platforms for digital marketing to include Social media (Facebook, Instagram, twitter etc) Digital advertising on google and other relevant platform Articles published in digital media including popular magazines like stir, pool design, design boom, core77 etc Digital media coverage on local, national and international digital news/media channels. He will head the team and will be available for 18 hours a week. The marketing plan should include a schedule of the posts, articles and coverage to be done for at least 3 months in advance and set goals for the output, in terms of traffic on the social media pages, reach (quantitatively), number of interactions on the social media platforms etc. The resource will also share the projected investment for the following month’s advertisement and share the bills on actuals with the concerned authority to get the reimbursements. Marketing head should also be available for on site / meeting at head office atleast once in two week. Necessary approvals to be taken from the concerned authority on the marketing plan and schedule created by the marketing head. Experience -should have an experiance of working in media and marketing related feild for atleast 5 years -Should have the knowledge of all the social media,national/international media platforms. -should have excelent communication skills Qualification- Bachelors in Hotel Management/ Facility Management, Masters in management

NS Digital marketing team - Role and Responsibility: Content WriterThe content writer is responsible for creating campaigns for the digital platform. The resource should be fluent in written English, Hindi to create copy for all creatives including daily social media posts, articles, advertisements, event posters etc. He/she will responsible for archiving and maintaining the data on a server to be accessed by all the systems of the marketing team. Content creation and proof reading will be the responsibility of the content writer. The copy to be precise and creative to respond to the need of the output. This will include tagline, body text, headlines, subtitles etc in required languages depending on the design and layout of the creative. He/She will be available for 30 hours, also to be available for on site / meeting at head office atleast once in two week. Experience- Proven work experience as a Content Writer, Copywriter or similar role Qulification BSc in Marketing, English, Journalism or related field

NS PR Funds for promotional activities - Funds for investment on PR activities including event organisation, digital media promostion, outdoor media promotion, media publication tie-ups, publication material production and other similar applications as per approval from department/design consultant. This cost need to be invested on actual for digital platforms like Facebook , Instagram and other social networking platforms . The cost can be used to push articals / advertisements made by the content and graphic team in national and international magazines, outdoor media,event collaboration, Media and news paper coverage,quarterly business and targets. The basic monthly cost will be reimbursed on actuals with the supportive document for reimbursements approved by the concerned authority. Depending on the footfall, season and other parameters the funds can be utilised over the period of 3 years as per the best use and need of the same in consultation and approval from the department/design consultant.after 1st lot

NS Photo Printout - Providing & supplying photo printouts

NS Annual maintainance cost of electrical items,Installations,Lighting fixtures etc- Year 2

NS Annual maintainance cost of electrical items,Installations,Lighting fixtures etc-Year 3

NS Museum staff uniform Males and female for both winters and summers of good quality fabric and design as per the approval by design consultant having museum branding.

NS Barcode scanners with turnstyle at the entry control and check the tickets. Refer image in the presentation. Rate to include the cost of server and maintenance.

NS Photography and videography project documentation - Photoshoot and video shoot of all work including equipment like drones, special camera/ other necessary equipment for the overall museum to be included. Minimum 50 high resolution edited photographs, and other photographs unedited RAW files to be provided. Photography and videography professionals to be nationally awarded for their architectural/interior photography and videography works. A minimum of 50 short videos of 60 second each for marketing purposes to be included. An approval for the choice of professional to be brought on board for photography and video works to be taken from the design consultant/ department. Previous works should be submitted for evaluation and approval of the same. The output of this work will be used for the reception video wall film, coffee table book/ brochure development, website, social media marketing and any other project related application.

NS theatre Director - he/she should train all the ushers/actors/artists how to present/act as per the script provided by the content writer/story teller according to the museum intent for specific space or gallery. person will be responsible to train the said artists for a minimum timeperiod of 20 days. This will include minimum 10 dress rehearsels where the director should be physically present. Regular periodic checks to be conducted to ensure the quality of the performance. In case the performance lacks, rectifications and improvisations to be made by the director. Experience- the directed should have a atleast 10 year of experience in directing shows/actors/theatre/performers Qualifaction- Graduate from nationally/internationally acclaimed university/school in the course of Acting/direction

NS Printing of coffe table book of size 180mm X 180mm of 1000 copies as approved by musuem consultant.the quality material, color etc of the final product should be exactly same as per the sample approved after the desigining phase.

NS Printing of coffe table book of size 300mm X 300mm of 1000 copies as approved by musuem consultant.the quality material, color etc of the final product should be exactly same as per the sample approved after the desigining phase.

NS Printing of Pamphlet(140mm X 210mm) of 1000 copies as approved by musuem consultant. The quality material, color etc of the final product should be exactly same as per the sample approved after the desigining phase.

NS Desighing of - Coffee book table - pamphlet - brochure - tickets Concept design, detail design and print ready files for the following: 1. Coffee table book of 2 different sizes a. 180mm X 180mm b. 300mm X 300mm The book would be of 100 pages atleast with premium print and paper quality. The content of the book should be convey the intent of the museum, insights from the design process, museum execution process and summmarise the overall project in all relevant aspects. The book to be made using 2d/3d graphics/illustration of international quality and proffessional images of the museum interors and context. The concept, content and approach to design to remain the same for both versions. The big and small books to be made such that the similar information can be produced in 2 varying sizes. 2. 10 leaf museum brochure of size 200mm X 700mm The brochure should include a brief overview of the museum and all the necessary information supported with 2d/3d graphics/illustration of international quality and proffessional images of the museum interors and context 3. Desigining Museum Tickets Custom designed tickets to be made for the visitors with all necessary information and should be connected to the museum narrative supported with 2d/3d graphics/illustration of international quality / proffessional images of the museum interors and context in a very compact format. 4. Pamphlet(140mm X 210mm) The pamphlet should include a brief overview of the museum and all the necessary information supported with 2d/3d graphics/illustration of international quality and proffessional images of the museum interors and context in a very compact format. Common Note: The cost of sampling to check material and print quality, layouting, graphics design to be covered in the item. The design language including colors, layout, imagery and typography to be in synchronisation with the museum branding theme. Stepwise approval on approach, index, concept design, pages layout, font type and sizes, coverdesign, pages design and color scheme should be taken, approval to be taken on the basis of samples received. The cost would also include 10 copies each of all the above mentioned 5 final products. The required copywriting and proofreading of international quality in the required languages to also be included in the item rate. copy-writing as per the requirement of the book

NS Primer base- Providing surface base on existing wooden panelling/partition with a smooth sand faced cement plaster with 2 base coat of water proof primer on top as per shade required after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application , being complete including cost of all material, labour, machinery, TandP, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Museum Consultant. The surface should be smooth enough for vinyl film application.

NS Supply, installation, testing and commissioning of Linear Strip Light RGB – IBL - 6412.C303510 - 24V LED Tape – IP20 : 3000K CRI)90 : 9.6W/m - 2835 - 120 LEDs/m with curve fitting and a diffuser cover over the light source to hide the point source, as per the required design intent and approved by the design colsultant - ERCO/iGuzzini/fagurhalt Zoom lens or Spot lens accessories to be supplied as per the project requirement. Product should be approved by Consultant/ Designer post the mock up. (AOR No.RA-39)

NS Reception Sculptural installation Designing, fabricating, installation and finishing of a sculptural installation highlighting the symbolism of tree as metaphor for the museum. This sculpture is a glimpse of the journey in the overall museum, it should be symbolic to the three major parts of the freedom struggle i.e. the war, the wound, the wish. The installation to be designed by special artists such as Subodh Gupta/ Mukul Goyal/ Vibhor Sogani and such nationally and internationally acclaimed artists. The artist should have expertise in large scale sculptures, landmark public installations of international standards. The artist to be finalised upon approval of the concept design submitted by them and approved by the museum design consultants. The size of the sculptural installation to be approximately 15m x 10m made of S.S./M.S./Zinc/wood/ Mdf/ terracotta/ Corian/ FRP/metal/ fabric/corten steel/ materials of Haryana craft and culture as per approved by the museum design consultant. The sculpture to have structure supports of MS sections/steel bars of size as per the structural requirements ensuring the strength and safety of the installation and the surroundings. This sculptural installation to be partly indoor and partly outdoors. The installation should be made such that it is weatherproof and should withstand the various challenges of an outdoor installation. A part of the tree to be at the museum reception indoor space is an extension of the installation, complementing the overall reception space and not outstanding the space. The installation includes the cost of the gravel, pebbles stones, and other equivalent materials complimenting the installation aesthetics and controlling the pedestrian movement around the installation. Please note that this is tentative description of the installation, the final specifications may vary as per the concept and design proposed by the artists/sculpturist. The installation quality, mechanism and finish should conform to the International standards of museums. The commissioned artist/execution agency on board for the installations to take necessary prior approvals from museum design consultant before execution. Please refer to the design presentation for further details. The installation should be complete in all respect with necessary approvals of museum design consultants and engineer -in-charge. The artist assigned should take all the necessary approvals from the museum design consultant.

MUSEUMS & EXPOS INTERNATIONAL LIMITED

a s enterprise