Construction of Degree College, Gola in Ramgarh District under Vinoba Bhave University, Hazaribagh

Amount

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

ProvidIng coarse clean sand In filling in foundation trenches or In plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour. royalty and taxes all complete as per building specification and direction of Ell ( Mode of measurement compacted volume).

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets etc. upto floor five level, excluding the cost of centring, shuttering and finishing :

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for all heights

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string course etc

Suspended floors, roofs, landings, balconies and access platform.

Shelves ( Cast in situ )

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Stairs, (excluding landings) except spiral-staircases.

Small lintels not exceeding 1.5m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.

Edges of slabs and breaks in floors and walls.

Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing Tor steel reinforcement of 8mm. dia rods as per approved design and drawing -do- -do- TMT Fe 500 {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

Providing Tor steel reinforcement of 10mm,12mm & 16 mm. dia bars as per approved design and drawing -do- -do-

a) 10 mm (TMT coiI Fe 500) {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

b) 12 mm (TMT coiI Fe 500) {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

c) 16 mm (TMT coiI Fe 500) {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

Providing Tor steel, reinforcement of 20mm, 25mm, 28mm, 32mm dia bars as per approved design and drawing-do- -do-

20/25 mm dia,TMT bar Fe 5OO {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

28/32 mm dia,TMT bar Fe 5OO {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).

All works upto plinth level

All works From Plinth Level & upto floor V level.

Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/ cum)

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 Including providing 10 mm thick mortar joints. cost of screentng materials raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 A brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 Including providing 10 mm thick mortar joints. cost of screentng materials sacffolding, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening matenals, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I

Providing designation 100 A brick Work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth. curing, taxes and royalty all complete as per building specification and direction of E/I.

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade

Area of slab up to 0.50 sqm.

Area of slab over 0.50 sqm.

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in doors and windows with black board core bended with high quality phenol formal dehydes synthetic resin both side commercial veneered of standard make with oxidized iron fittings such as hinges, tower bolts, handle, cleast and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing and fixing aluminium sliding door bolts anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters.

Exceeding 10.00 sqm and upto 16.80 sqm in the area

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.

62 mm thick cement concrete flooring with concrete hardener topping,under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm.

Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness.

Providing and laying Double Charge Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622/ ISO 13006, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand ), jointing with grey cement slurray @ 3.3 k.g / sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600 x 600 mm .

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Size of Tile 600x600 mm

Providing and laying 25mm thick kotah stone slab flooring of approved size, texture and colour over 19mm. thick base of lime morter (1:1:1) (lime putty:surkhi:coarse sand) laid over and Jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandium stone including cost of curing, taxes and royalty all complete as per building speclflcationand direction of Ell.

iv) 600X600 mm Size

Providing and laying 25mm thick kotah stone tiles In risers of steps, skirting, and pillars of approved size, texture and colour laid over 12mm. thick cement mortar (1:3) and joined with grey cement slurry mixed with pigment to match the shade of the slab including rubbing to granolilthic finish with approved quality -do-

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra for Kota stone/ sand stone in treads of steps and risers usingsingle length up to 1.05 metre.

Extra for pre finished nosing to treads of steps of marble/ granite stone.

Extra for marble/ granite stone flooring in treads of steps and risers using single length up to 2.00 metre.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete .

Providing and Fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams .

Providing and Fixing 100 mm diameter and 60 cm long rain water spout in cement mortar 1:4 ( 1 Cement : 4 Fine Sand )

Stone ware Spout

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with :

GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing.

Providing sand stone slab for roofing and laying them in cement mortar 1: 4 (1 cement : 4 coarse sand) over wooden karries or R.C.C. battens or structural steel sections (Karries or battens or structural steel sections to be paid separately), including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 fine sand ) complete :

Red sand Stone Slab

40 to 50 mm thick

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

15 mm cement plaster on rough side of single or half brick wall of mix:

1:6 (1 cement: 6 coarse sand)

12 mm cement plaster finished with a floating Coat of neat cement of mix :

1:6 (1 cement : 6 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Providing and applying 12 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M 1.5 with 5% cico or any other approved water proofing compound.-do

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/I.

Making 6x6mm grooves in plaster surface over walls truly horizontal of vertical as specified at regular intervals, at all heights including cleaning, finishing, scaffolding and curing with all leads and lifts of water all complete as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone of fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I

providing two coat of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty whwerever required scaff folding washing of floors and texes all complete as per building specification and dircetion of E/I

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Providing two coat of synthetic enamel paint of approved shade and make over new wooden surface do/-

Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated rainscreen tiles of height 250/ 300/ 400mm and length of 595 mm of approved texture,design and pattern having Flexural Strength/ Modulus of Rupture of ? 14 N/m² and maximum water absorption of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting aluminium framework(Alloy 6063 T5/T6) consisting of vertical 'T' (for intermediates)/ 'L'(for ends/ termination)/ Tubular sections (at corners)of size 80x60x2mm/ 40x60x2mm/ 40x40x2mm respectively, spaced at maximum spacing of 600mm c/c matching to the tile vertical grid, and horizontal aluminium 'C'-clamps of size 56x25x2mm thickness of length 150mm at junction of tiles and of length 75mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/ 300/ 400mm c/c matching to the tile horizontal grid with two numbers of self-drilling / self-tapping SS screws of size 5.5x25 mm with EPDM washers.The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-dip-galvanized) steel L-brackets (galvanizing thickness of minimum 80 microns)of size 110x80x6 mm at intermediate vertical aluminium profiles and of size 220x110x12 mm at outer corners and stainless steel grade 304,M10 full threaded anchor fasteners with nylon sleeve 100mm long (for brick work) and M8 expansion anchor fasteners 75mm long for concrete surface, spacing of brackets to be based on a structural/ static calculation.

The brackets shall be of length 175mm at junction of two vertical aluminium profiles and of length 100mm at intermediate points of vertical profiles and shall be fixed to the vertical aluminium T / L / Tubular profiles using two numbers self-drilling/ self-tapping SS screws of size 5.5x25mm with EPDM washers. EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles shall be mounted on the ‘C’ clamps such that the tiles are supported at top and bottom at both ends. The tiles shall be additionally secured to the horizontal ‘C’ clamps using special SS clips of required size which shall be inserted and pressed into position on the ‘C’ clamps holding the tiles and the cut-tiles shall be glued at points to the horizontal ‘C’ clamps by using MS Polymer sealant adhesive. Thevertical joint open groove between two adjacent tiles shall be 5mm. The tiles and system shall be designed to resist wind load as per IS 875 (Part 3) according to different zones. The tiles shall be installed using the ventilated rain screen principle with provision for natural ventilation of the space between the façade tiles and the structural wall. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge. Note : Scaffolding wherever required to be paid separately.

With 16mm thickness (+/- 10%) terracotta tiles of other than grey colors

Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Embankment Construction with Material Obtained from Borrow Pits (Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2)

Rolling with vibratory roller

Granular Sub-base with Close Graded Material (Table:- 400-1)

Plant Mix Method (Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 )

for grading- I Material

for grading- II Material

for grading-III Material

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.)

With Vibratory Roller

"Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).

Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

Cement concrete prepared with batch mixing machine

Footpaths and Separators (Construction of footpath/separator by providing a 150 mm compacted granular sub base as per clause 401 and 25 mm thick cement concrete grade M15, over laid with precast concrete tiles in cement mortar 1:3 including provision of all drainage arrangements but excluding kerb channel.)

Dry Lean Cement Concrete Sub- base (Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing.)

Cast in Situ Cement Concrete M20 kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408)

Using Concrete Batching and Mixing Plant

Retro- reflectorised Traffic signs (Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)

90 cm equilateral triangle

60 cm equilateral triangle

60 cm circular

80 mm x 60 mm rectangular

60 cm x 45 cm rectangular

60 cm x 60 cm square

90 cm high octagon

Direction and Place Identification signs upto 0.9 sqm size board. (Providing and erecting direction and place identification retro-reflectorised sign asper IRC:67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing)

Direction and Place Identification signs with size more than 0.9 sqm size board. (Providing and erecting direction and place identification retro- reflectorised sign asper IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)

Overhead Signs (Providing and erecting overhead signs with a corrosion resistant aluminium alloy sheet reflectorised with high intensity retro-reflective sheeting of encapsulated lense type with vertical and lateral clearance given in clause 802.2 and 802.3 and installed as per clause 802.7 over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plans)

Truss and Vertical Support

Aluminium alloy plate for over head sign

Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Painting on Steel Surfaces (Providing and applying two coats of ready mix paint of approved brand on steel surface after through cleaning of surface to give an even shade)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)

Kilo Metre Stone (Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc)

Ordinary Kilometer stone (Precast)

Road Delineators (Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide stripes, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and confirming toIRC-79 and the drawings.)

Reinforced Cement Concrete Crash Barrier (Provision of an Reinforced cement concrete crash barrier at the edges of the road, approaches to bridge structures and medians, constructed with M-20 grade concrete with HYSD reinforcement conforming to IRC:21 and dowel bars 25 mm dia, 450 mm long at expansion joints filled with pre-moulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No. RW/NH - 33022/1/94-DO III dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineer, all as specified)

M 20 grade concrete

Metal Beam Crash Barrier

Type - A, "W" : Metal Beam Crash Barrier (Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 810)

Type - B, "THRIE" : Metal Beam Crash Barrier (Providing and erecting a "Thrie" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 85 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 2 m high with 1.15 m below ground level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a space of channel section 150 x 75 x 5 mm, 546 mm long complete as per clause 810)

Flexible Crash Barrier, Wire Rope Safety Barrier (Providing and erecting a wire rope safety barrier with vertical posts of medium weight RS Joist (ISMB series) 100 mm x 75 mm (11.50 kg/m), 1.50 m long 0.85 m above ground and 0.65 m below ground level, split at the bottom for better grip, embedded in M 15 grade cement concrete 450 x 450 x 450 mm, 1.50 m center to center and with 4 horizontal steel wire rope 40 mm dia and anchored at terminal posts 15 m apart. Terminal post to be embedded in M 15 gradecementconcretefoundation2400 x 450 x 900 mm (depth), strengthened by a strut of RS joist 100 x 75 mm, 2 m long at 450 inclination and a tie 100 x 8 mm, 1.50 m long at the bottom, all embedded in foundation concrete as per approved design and drawing, rate excluding excavation and cement concrete.)

Spreading of Sludge Farm Yard Manure or/and good Earth (Spreading of sludge farm yard manure or/ and good earth in required thickness (cost of sludge, farm- yard manure or/and good earth to be paid for separately))

Grassing with ' Doobs' Grass (Grassing with 'Doobs' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed)

In rows 15 cm apart in either direction

In rows 7.5 cm apart in either direction

Making Lawns including Ploughing and Dragging with 'Swagha' Breaking of Clod (Making lawns including ploughing and breaking of clod, removal of rubbish, dressing and supplying doobs grass roots and planting at 15 cm apart, including supplying and spreading of farm yard manure at rate of 0.18 cum per 100 sqm)

Maintenance of Lawns or Turfing of Slopes (Maintenance of lawns or Turfing of slopes (rough grassing) for a period of one year including watering etc)

Turfing Lawns with Fine Grassing including Ploughing, Dressing (Turfing lawns with fine grassing including ploughing, dressing including breaking of clods, removal of rubbish, dressing and supplying doobs grass roots at 10 cm apart, including supplying and spreading of farm yard manure at rate of0.6 cum per 100 sqm)

Maintenance of Lawns with Fine Grassing for the First Year

a) Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart)

Maintenance of Hedge for one year

a) Planting Flowering Plants and Shrubs in Central Verge

Maintenance of Flowering Plants and Shrubs in Central Verge for one Year

Planting of Trees and their Maintenance for one Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year)

Renovation Lawns including, Weeding, Forking the Ground, Top Dressing with Forked Soil (Renovation lawns including, weeding, forking the ground, top dressing with forked soil, watering and maintenance the lawns, for 30 days or more, till the grass forms a thick lawn, free from weeds, and fit for moving and disposal of rubbish as directed, including supplying good earth, if needed but excluding the cost of well decayed farm yard manure)

Supply at Site Well Decayed Farm Yard Manure (Supply at site of work well decayed farm yard manure, from any available source, approved by the engineer in charge including screening and stacking)

Wrought Iron and Mild Steel Welded Work (Wrought iron and mild steel welded work) (using angles, square bars, tees and channel grills, grating frames, gates and tree guards of any size and design etc. including cost of screens and welding rods or bolts and nuts complete fixed in position but without the cost of excavation and concrete for fixing which will be paid separately)

Tree Guard with MS Angle Iron and Steel Wire (Providing and fixing tree guard 0.60 metre square, 2.00 metre high fabricated with MS angle iron 30 x 30 x 3 mm, MS iron 25 x 3 mm and steel wire3 mm dia welded and fabricated as per design in two halves bolted together)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basins with C.P. brass pillar tap, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls and floors where required.

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and Fixing soil,waste and vent pipes:

100 mm diameter

Centrifugaly cast (spun) iron socket & spigot (S&S) pipe as per IS:3989

75 mm diameter

Centrifugally cast (spun) iron socketed pipe as per IS:3989

Supplying fitting and fixing 40mm high vitreous white glazed earthen E.W.C. With 'P' trap of parry hindustan or any other approved I.S.S. Make including supplying and fixing 15 litres C.I. Mosquito proof low down flushing cistern of approved make with complete fittings With C.I. handle and R.S. or bracket with telescope flush pipe with brass coupling and plumbers joints spindle stop cock of approved uality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved pain over a coat of red oxide priming all complete as per specification and direction of E/I. (a) 12.5 lit. Low level PVC Cistern

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. Of parry Hindustan or any other I.S.S. Approved make with 100mm H.C.I. 'P' trap 15liters C.I. Pull and let go flushing cistern of names or other I.S.S. Equipment make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pert of vitreous white glazed earthenwere were footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. (b) with 12.5 lit. Low level PVC Cistern

Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. Approved make supported on painted C.I. Or R.S. Bracket 32mm C.I. Brass waste, 15 mm dia C.I. Body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plunber joints etc. all complete as per specification and direction of E/I.

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required

Kitchen sink with drain board

510x1040 mm bowl depth 250 mm

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :

Supplying fitting and fixing flat back or anguler lipped front viterous white glazed earthen ware urinal of Hindustan '' Parry '' or any other approved ISS make with 5 Litre Capacity CI automatic flushing cistern of reliance for any other I.S.S approved make with all fittings with C.I or R.S brackets standard size GI flush pipe with fitting clamps , 15 mm CI body brass spindle stop cock of approved quality weight not less than 400 grams , 15 mm PVC / Alkthene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide , cutting wall and floor , making good the same etc . all complete as per specification and direction of engineer - in - charge . ( a ) flat back or standing corner ( 600 mm x 350 mm )

Providing and Fixing stone slab with table rubbed , edges rounded and polished of size 75 x 50 cm deep and 1.8 cm thick , fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded stone finished smooth aggregate 6 mm nominal sizes ) as per direction of engineer - in - charge .

Granite Stone of approved shade

Providing & fixing toilet paper holder:

C.P.brass

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931 .

Bib Cock ( ISI )

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Bib Cock ( Long Thread )

Providing and fixing 15 mm dia and 45 cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of engineer - in - charge .

Providing and fixing Mirror of 6 mm thick plain glass 600 mm x 450 mm beveled edge mirror including CP brass revolving fittings 3 mm plywood board and CP hinges etc to fix the mirror .

Providing and Fixing 40 mm CP brass waste for WHB for Sink

Providing and Fixing CP brass 32 mm size Bottle Trap of approved quality and make as per the direction of Engineer - in- charge .

Providing and fixing C.P. Brass Angular Stop Cock ( Long Thread )

Providing & fixing of Waste pipe for Sinks including pvc waste fittings complete.

40 mm dia PVC waste pipe 750 mm long with coupling

Providing and placing on terrace ( at all floor levels ) polythylene water storage tank of approved brand and manufacture with cover and suitable locking arrangment and making necessary holes for inlet,out let and over flow pipes but without fitting and the base support for tank .

Providing & fixing CP brass liquid soap solution holder 109mm wide,125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour. weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and Fixing white viterous china extended wall mounting water closet of size 780 x370 x690 mm of approved shade including providing and fixing white viterous china cistern with dual flush fitting , of flushing capacity 3 litre / 6 litre ( adjustable to 4 litre / 8 litre ) , including seat cover and cistern fittings , nuts , bolts and gasket etc . complete .

Providing and fixing wash basin with C.I. brackets 15 mm dia CP brass single hole basin mixer of approved quality and make including painting of fittings and brackets cutting and making good the walls wherever required

White Viterous china Wash basin size 550x400 mm with a 15 mm CP brass single hole basin mixer

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes of SFMC/AQUATHERM/HELIROMA brand confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc.

Concealed work, including cutting chases and making good the walls etc.

PN - 16 Pipe, 20mm OD (SDR-7.4)

PN - 16 Pipe, 25mm OD (SDR-7.4)

PN - 16 Pipe, 32mm OD (SDR-7.4)

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc

Internal work - Exposed on wall

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes of SFMC/AQUATHERM/HELIROMA brand onfirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. Internal Exposed on walls

PN - 16 Pipe, 20mm OD (SDR-7.4)

PN - 16 Pipe, 25mm OD (SDR-7.4)

PN - 16 Pipe, 32mm OD (SDR-7.4)

PN - 16 Pipe,40mm OD (SDR-7.4)

PN - 16 Pipe,50mm OD (SDR-7.4)

Providing and Fixing Gunmetal Full way valve of approved quality , all complete , as per specification and direction of engineer - in - charge .

15 mm dia and weight not less than 300 gms .

20 mm dia and weight not less than 400 gms .

25 mm dia and weight not less than 500 gms .

32 mm dia and weight not less than 700 gms .

40 mm dia and weight not less than 1.0 Kg .

50 mm dia and weight not less than 1.5 Kg .

Providing double flange sluice valve ( size 50 mm to 1200 mm ) conforming for IS : 14846 including worn gear arrangements as per test pressure stainless steel spindle , caps transportation etc all complete .

with byepass arrangements - PN : 1.6

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,re

15 mm Dia pipe

25 mm nominal outer dia Pipes

Constructing brick masonry chamber 30x30x50cms inside with 1st class brick work in cement mortar 1:5 (1 cement : 5 fine sand) for stop cock with CI surface box 100x100x75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design.

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with channel lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design:

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 90X90X100 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with channel lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design:

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Painting GI Pipes and Fittings with two coats of anticorrosive bitumastic paint of approved quality .

15 mm diameter pipe

20 mm diameter pipe

25 mm diameter pipe

32 mm diameter pipe

40 mm diameter pipe

50 mm diameter pipe

65 mm diameter pipe

80 mm diameter pipe

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931

a) 15 mm nominal bore

Providing and fixing C.P brass angle valve for basin mixer and geyser points of approvedquality confirming to IS:8931

15 mm nominal bore

Providing & fixing enclosed type water meter ( bulk type ) conforming to IS : 2373 and tested by municipal board complete with nuts , bolts , rubber insertion etc . ( The tail piece if required will be paid saperately )

80 mm dia nominal bore

Providing & fixing C.I dirt box strainer for bulk type water meter with nuts , bolts , rubber insertion etc . complete conforming to IS : 2373

80 mm dia nominal bore

Providing push on joints to centrifugally cast (spun ) iron pipes or Ductile iron pipes including testing of joints and the cost of rubber gasket

100 mm diameter pipe

150 mm diameter pipe

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.

15 mm nominal bore with 45 cm length

Providing, laying and jointing glazed stone ware pipes grade `A' with stiff mixture of cement mortar in the proportion of 1:1 (1cement :1 fine sand) including testing of joints etc complete.

100 mm diameter

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 gradded stone aggregate 40 mm nominal size) upto haunches of S.W. Pipes including bed concrete as per standard design.

100 mm diameter

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, aneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mmthickness

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for separately).

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Upto 5mm depth and 5 mm width

Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete.

Powder coated minimum thickness 50 micron aluminium

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of :

(i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.

Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge :

Using rough kota stone.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying a) First layer of slurry of cement @ 0.488 kg/sum mixed with water proofing cement compound @ 0.253 kg/sum. This layer will be allowed to air cure for 4 hours.b) Second layer of slurry of cement @ 0.242 kg/sum mixed with water proofing cement compound @ 0.126 kg/sum. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Water proofing for Old and New Roof Slab:- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with, brush, roller or spray for water proofing coating as per manufacturer specifications with following steps: (a surface preparation-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika India Pvt Ltd /MYK Schomberg/Dr Fixit/Fosroc or equivallent Providing and reparing of all comers and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150 mm X 150 mm fillet of mortar (Cement: sand-1:4) admixed with acrylic polymer of Sika Fosroc/MYK Schomberg Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry ofacrylic polymer. Repairing surface irregularities, damaged concrete in base slab, dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete. (b)1st Coat Apply 1st coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roiler After 1st coat of application, 45 gsm of Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg / Samt/coat. For the purpose of measurement the entire treated surface will be measured." (c) 2nd Coat-To apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle to the 1st coat over the glass fibre laid surface 2nd coat should be applied @0.7 kg/Samticoat For the purpose of measurement the entire treated surface will be measured After three days of drying the 2nd coat, the rail water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of EIC. The waterproof coating to be protected from damage before screed over it. Waterproofing Brand- Sika Topseal 109hi/Fosroc Brushbond RFX/Dr Foxit Pidiffin 2K/MYK Aquafin TG Product Performance - Chemical Base Part A Acrylic copolymer, Part B Specially graded cementitious powder- Density 1.6 kg/l (mixed density) at +27°C Tensile Strength -2 Nimm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Strength -2 N/mm2 (concrete failure) (According to ISO 4624) Slant-Shear Bond Strength -4 N/mm2 (According to FIP 5.15) Elongation at Break -35% without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370) (d) Protection of treated surface with PCC-The treated surface should be covered with 25mm/ 50mm PCC of M-20 grade(1:1.5:3) with proper slope (1:120) towards the rain outlets in alternate panels of 2 mt x 2mt keeping 6 mm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 @of 100 ml per bag of of cement to be added in the screed concrete(paid separately for this items) All corners shall be chamfered with 150mm x 150 mm fillet. The rain water outlets shall be just leveled with the screed concrete to ensure smooth discharge of water the peripheral gaps between pvc pipe outlet and concrete surface should be packed property with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of Sika India Pvt. Ltd. /MYK Schomberg/Dr Fixt/Fosroc For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately). Brand- Sika India Pvt Ltd./MYK Schomberg/Dr Foxit/Fosroc Warranty for five years.

Covering of treated surface with PCC :- Providing 50 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F.M 2.5 to 3 including screening,shuttering and mixing cement concrete in mixer with admixture of integral water proofing and placing in position,striking curing,taxexand royality all complete as per building specifiction and direction of Ell.Panels that has been left should be casted next day.There should be 6 mm gap between Panels .Brand-Sika­ P\astocrate plus, MYK proof WP 1O,Fosroc-Conplast X4211 C,Dr.fixit Pidiproof LW+ or Equivalent .

5.12.8. Providing and filling of 6 mm thickGroove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge.(with 18% GST) .Brand:-Sika-Polysulphide, Fosroc-Thioflex 600,Dr. Fixit Pidiseal PS(42P),MYK Seal PS or Euivalent

Stone Chipps / stone aggregate (20 km )

Coarse Sand ( 20 km)

Brick (8 km) (1 K + 7 P)

Fly Ash Brick (8 km )

Local Sand (3km)

Earth ( 1 km)

Stone metal lead = 22 km

Wiring for light point/ fan ponit/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable size Gl box etc.as required.

Group C

Wiring for circuit/ submain wiring along with earth wire with the following sizes PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 x 10 sq. mm + 1 x 6 sq.mm earth wire

2 x 16 sq. mm + 1 x 6 sq.mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following size of FR PVC insulated copper conductor, single core cable in the existing surface / recessed PVC conduit as required.

6 x 1.5 sq. mm (4 X 1.5 sq.mm + 2 X 1.5 sq. mm)

9 x 1.5 sq. mm (6 X 1.5 sq.mm + 3 X 1.5 sq. mm)

Wiring for light/ power plug with 2 X 4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recesed PVC conduit along with 1 No. 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4 X 4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit along with 2 Nos. 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required

Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc, as required.

Supplying and fixing suitable size of GI box with modular plate and cover in front on surface or in recess including poviding and fixing 6 pin, 15/16 amps modular socket outlet and 15 / 16 amps modular switch. connection, painting etc, as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. For AC

Supplying and fixing following modular type switch/ socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required.

Telephone socket outlet

TV antenna socket outlet

Supplying and fixing following size/modules G.I. box along with modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (75mmX75mm) (for Telephone, Television, Fan reguletor)

Providing and fixing plain 16/0.20mm (0.50sqmm) twin twisted, flexible, FR PVC insulated, copper cable, in conduit of suitable size on the floor/ wall, or side of the table/ door etc. as required.

Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed PVC conduit as required.

Supplying and drawing co-axial cable RG-6 grade copper conductor, PE insulated with PVC sheath in the existing surface/recessed PVC conduit as required.

Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required.

25 mm ( for TV, Telephone, & circuit wiring)

32 mm ( for TV, Telephone, & circuit wiring)

Supply, installation, testing & commissioning of Bulk head fitting with 9/10 Watt CFL/LED

Supply, installation, testing & commissioning of 18W Surface mounted Round LED Downlighter delivering an initial system lumen of 1527 lumens & the luminaire shall be with system efficacy ≥ 84 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: PMMA LGP/Polysterene Diffuser. The operating CCT shall be 6000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. (cat no.LD80-171-XXX-60-SM)

Supply, installation, testing & commissioning of 36W Surface/ Suspended 500mm Round Led Fixture delivering an initial system lumen of 3230 lumens & the luminaire shall be with system efficacy ≥ 95 lm / W. Housing: CRCA. IP20 , Optics: HET Diffuser. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. (cat no.LM71-441-XXX-57-XX)

Supply, Installation, testing and commissioning of LED mirror light with power 8/10W , rated voltage 230 V 50Hz aluminium/PC body with running life minimum 30000 Hours

Supply, installation, testing & commissioning of 15W Surface mounted Square Led Downlighter delivering an initial system lumen of 1350 lumens & the luminaire shall be with system efficacy ≥ 90 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: PMMA LGP/Polysterene Diffuser. The operating CCT shall be 5000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard.

Supply, installation, testing & commissioning of flowing rating reccess/surface mounted LED Round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS: 10322 part-5/section-2 or IEC:62722 with necessary accessories as required

12 W LED Round Down light

S.I.T.C of following size ceiling fan 3 blades confirming to IS:373:2019 including wiring the down roads of standard length ( upto 30cm) with 1.5 sq.mm FR PVC insultated , copper wire suitable for 230 V 50 Hz , single phase supply etc complete as required.

1200mm(48") BLDC 5 star rating 32 W Ceiling Fan

S.I.T.C 12" (300MM) metal exhaust fan

Supplying and fixing of Stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as reqd.

Installation of exhaust fan upto 450 mm. sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damange, connection, testing, commissioning etc as required.

Extra for fixing the louvers shutters complete with frame for a exhaust fan of all sizes.

MAIN BOARD FOR (ESSENTIAL)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar,din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way, double door

12 way, double door

Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)

6 way (4 + 18), Double door

8 way (4 + 24), Double door

S/F Vertical Type T.P MCB DB- Supplying and fixing of following ways surface/recess mounting,vertical type ,415 volts ,TPN MCB distirbution board of sheet steel , dust protected duly powder painted , inclusive of 200Amps tinnned copper bus bar, common neutral link , earth bar ,din bar for mounting MCB's.

8 way(8+36)Double door ,vertical type

Supplying and fixing following rating, DP 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole,415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole,(Single phaseand neutral), 240volts residual current circuit breaker (RCCB), having a sensitivity current 30mA in the existing MCB DB complete with connection, testing and commissioning ets. As required.

Supplying and fixing following rating, double pole,(Three Phase and neutral), 415 volts residual current circuit breaker (RCCB), having a sensitivity current 30mA in the existing MCB DB complete with connection, testing and commissioning ets. As required.

Supplying and fixing following rating, double pole, 240 volts, 'C" series, miniature circuit breaker suitable for inductive loads in the existing MCB DB complete with connections, testing and commissioning etc. as required.

6/32 amps, single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as required. (but without charcoal or coke and salt)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode, as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/recessed conduit / submain wiring

Supplying and drawing of UTP 4 pair CAT6 LAN cable in the existing surface /recessed steel /PVC conduit as required (1 run of cable).

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

2 Loop Panel

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and drawing of UTP 4 pair CAT6 LAN cable in the existing surface /recessed steel /PVC conduit as required (1 run of cable).

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

P/ F MV Danger Notice Plate

Providing and fixing MV Danger Notice Plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides and with inscription in single red colour on front side as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV grade of size exceeding 120 sq mm but not exceeding 400 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Above 120 sq. mm and upto 400 sq. mm.

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

P/ F RCC Hume Pipe

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

150 mm dia ID

300 mm dia ID

Design, manufacture, supply, erection, testing & commissioning of following rating of DG Sets in Accoustic Enclosure, having self excited & self regulated 415 V, 3 Phase, 4-Wire, 50 Hz, 0.8 p.f. Alternator coupled with multi-cylinder, turbo-charged/ turbo-charged after cooled as called for, Diesel Engine capable to generate the power not less than the required BHP to achieve the alternator capacity as given below, with radiator Cooled, hospital type silencers and Electronic governer (G3 Governing System), DG set controller suitable for Auto Synchronization & Auto Load Sharing with microprocessor based Synchronization relay like Woodward/Dief/ Deepsea or equivalent including providing of Engine control panel, 24V batteries of suitable rating, battery-charger with battery leads, inbuilt oil fuel tank of capacity as per OEM standards and complete with all standard accessories & protection as required and as per specifications, including first filling of lube oil, fuel tank, providing common base plate, anti vibration pads, drip trays, foundation bolts, nuts, bolts, cable termination/adopter box sutiable to terminate upto 5 nos. of 3.5Cx300 sq.mm. XLPE cables as required for a complete installation including RCC/PCC foundation for DG set as per the structural detail for Dynamic Load submitted by the Vendor and approve by the Client. DG set should comply relevant Indian standards. DG shall have Remote Monitoring System.

100 KVA (With Acoustic Enclosure)

Laying of one number of PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size as following in ground including excavation ,sand cushioning , protective covering and refilling the trench etc as required.

Up to 35 sq mm.

Above 35 sq mm and up to 95 sq mm.

Above 95 sq mm and up to 185 sq mm.

Above 185 sq mm and up to 400 sq mm.

Laying and fixing of one no PVC insulated and PVC sheathed /XLPE power cable of 1.1 kV grade of following size on wall surface as required.

Up to 35 sq mm. (Clambed with 1mm thick saddle)

Above 35 sq mm and up to 95 sq mm. (Clambed with 20 x 3 mm GI tape)

Above 185 sq mm and up to 400 sq mm. (Clambed with 20 x 3 mm GI tape)

S/ F powder coated of approved shade MS Cable Trays

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required..

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 62.5 mm depth X 2.0 mm thickness

S/ F powder coated of approved shade MS Cable Tray Bends

Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray bends with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

S/ F powder coated of approved shade MS Cable Tray Tee's

Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray tee's with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

S/ F powder coated of approved shade MS Cable Tray Cross Members

Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray cross members with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

300 mm width X 50 mm depth X 1.6 mm thickness

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required.

4 x 10 sq. mm

4 x 16 sq. mm

4 x 25 sq. mm

3½ x 35 sq. mm

3½ x 50 sq. mm

3½ x 70 sq. mm

3½ x 95 sq. mm

3½ x 120 sq. mm

3½ x 150 sq. mm

3½ x 185 sq. mm

3½ x 240 sq. mm

3½ x 300 sq. mm

Providing and fixing 25 mm X 5 mm G.I. strip at 0.50 m below ground as strip ectrode, including connection/terminating with G.I. nut,bolt, spring, washer excavation and re-filling etc. as required.( Jointing shall be done by overlaping and with 2 sets of GI nut & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. 2 nos used for 50 x 5 for the Neutral earthing of euipments )

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Earthing with Cu. earth Plate 600mm x 600mm x 3mm thick including accesssories, and providing masonary enclosure with cover plate (CI heavy duty) having locking arrangement and watering pipe of 2.7 mtr long etc. with charcoal or coke and salt ) as required.

Providing and fixing of lightning conductor finial,made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Reverting ,sweating and soldering of copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Above 6.5 metre and upto 8.0 metre

Supplying, installation, testing and commissioning of Flood light IP66 LED fitting suitable for 200 watt having system lumen output of minimum 20000 lumens complete with all accessories and lamp. PF better than 0.9, CRI better than 70 complete with all accessories. Wipro Cat No.: LF20-272-060-57-G2

Supplying, installation, testing and commissioning of Flood light IP66 LED fitting suitable for 100 watt having system lumen output of minimum 10000 lumens complete with all accessories and lamp. PF better than 0.9, CRI better than 70 complete with all accessories. Wipro Cat No.: LF20-122-060-57-G2

Supplying, installation, testing and commissioning of Bollard light fitting suitable for 11 watt IP 65LED having system lumen output of minimum 900 lumens complete with all accessories and lamp. Wipro Cat No.: LB14-131-XXX-65-05

Supplying, installation, testing and commissioning of 45 watt IP 65 LED POST light fitting having system lumen output of minimum 4500 lumens, Pure polyester UV resistant powder coated die cast aluminium housing with PMMA clear diffuser for uniform illumination, PF better than 0.9, CRI better than 70 complete with all accessories suitable for vertical/horizontal mounting on pole complete with connections etc as required. Wipro Cat No.: LP07-501-XXX-57-CL

Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc in ground including welding excavation and Providing cement concrete blocks as supports anticorrosive treatment with coaltar / asphalts tape as per IS :10221 refilling the trench etc of following sizes complete as required .

150 mm dia

100 mm dia

80 mm dia

Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required .

25 mm dia

80 mm dia

100 mm dia

150 mm dia

Supplying Fixing Testing and Commissioning of butterfly valve of PN 1.6 Rating with Bronze Gunmetal Sheet duly ISI marked complete with nuts , bolts , washers , gaskets conforming to IS : 13095 of following sizes as required .

80 mm dia

100 mm dia

150 mm dia

Supplying Fixing Testing and Commissioning of double flanged sluice valve of Rating PN 1.6 with non rising spindle bronze gunmetal seats ISI marked complete with nuts , bolts , washers , gaskets and conforming to IS : 14846 of following sizes complete as required .

80 mm dia

100 mm dia

150 mm dia

Providing Installation Testing and Commissioning of Non Return Valve of following sizes conforming to IS : 5312 complete with rubber gasket , GI Bolts , Nuts , washers etc as required .

100 mm dia

150 mm dia

Providing Installation Testing and Commissioning of Stainless Steel Y Strainer fabricated out of 1.6 mm thick stainless steel , Grade 304 , Sheet with 3 mm dia holes with stainless steel flange .

150 mm dia

Supplying and Fixing Single Headed Internal Hydrant Valve with instantaneous gunmetal material coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS : 5290 ( Type A ) with blank Gunmetal material cap and chain as required .

Single Headed Gunmetal Material

Supplying and Fixing orifice plate made out of 6 mm thick stainless steel ( Grade 304 ) with orifice of required size to be fitted between flange and landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg / sqcm complete as required .

Supplying and Fixing 63 mm dia 15 m Long RRL Hose pipe with 63 mm dia male and female coupling duly bound with GI wire , rivet etc . Conforming to IS : 636 ( Type A ) as Required .

Gunmetal Material

Supplying and Fixing First aid hose reel with MS Construction Spray painted in Post office red conforming to IS : 884 complete with the following as required

20 mm nominal internal dia water hose thermoplastic ( Textile Reinforced ) Type - 2 as per IS : 12585

20 mm nominal internal dia gunmetal globe valve and nozzle

Drum and Brackets for fixing the equipments on wall

Connections from Riser with 25 mm dia stop gunmetal valve and MS Pipe and socket

36.5 Metre Length

Supplying and Fixing 63 mm dia Gunmetal Short Branch Pipe with 20 mm nominal internal diameter size nozzle conforming to IS : 903 suitable for instantaneous connection to interconnect hose pipe coupling as required .

Gunmetal Material

Supplying and Fixing of Fire brigade connection of Cast iron body with gunmetal male intantaneous inlet coupling complete with cap and chain as required for suitable dia ms pipe connection conforming to IS : 904 as required

2 Way - 100 mm dia MS Pipe

Supplying and Fixing Air Vessel made of 250 mm dia 8 mm thick ms sheet 1200 mm in height with air release valve on top and flanged connection to riser drain arrangement with 25 mm dia gunmetal wheel valve with required accessories pressure gauge and painting with synthetic enamel paint of approved shade as required

Providing and Fixing of Pressure Switch in MS Pipe Line including connection etc as required

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 19.6.2-150 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

GI Pipes ( Tata Mark or Equivalent ) as per IS : 1239 ( Part -1 ) / 2004 ISI marked Medium Quality

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Providing and Fixing Gunmetal Full way valve of approved quality , all complete , as per specification and direction of engineer - in - charge .

15 mm dia and weight not less than 300 gms without wheel

20 mm dia and weight not less than 400 gms without wheel

25 mm dia and weight not less than 500 gms without wheel

32 mm dia and weight not less than 700 gms without wheel

40 mm dia and weight not less than 1.0 kg without wheel

50 mm dia and weight not less than 1.4 kg without wheel

65 mm dia and weight not less than 1.8 kg without wheel

80 mm dia and weight not less than 2.5 kg without wheel

Supplying and Fixing of Gunmetal Ferrule as per IS : 2692 of approved make in Existing CI main including drilling and tapping CI main all complete as per specification and direction of engineer - in - charge .

25 mm dia weight not less than 900 gms

Supplying and Fixing GI fittings of approved make ( conforming to IS : 1879 ) all complete as per specification and direction of engineer - in - charge .

GI Bend

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Elbow

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Tee Plain

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Reducing Tee Plain ( Taking Larger Dimension )

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Socket Plain ( Taking Larger Dimension )

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Reducing Socket Plain ( Taking Larger Dimension )

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Union Socket

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Plugs

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Jam Nuts

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

GI Nipple

15 mm dia x 100 mm long

20 mm dia x 100 mm long

25 mm dia x 100 mm long

32 mm dia x 100 mm long

40 mm dia x 100 mm long

50 mm dia x 100 mm long

65 mm dia x 100 mm long

80 mm dia x 100 mm long

Providing and Supplying ISI mark Centrifugally cast ( spun ) Ductile Iron Pipes of 100 mm and above all daimeter of water works with socket and spigot ends conforming to IS : 8329 / 2000 in the Standard working lengths of 4.5 , 5.5 & 6 m suitable for classification K-7 & K-9 suitable for push on joints ( rubber gasket D jointing ) with cement mortar lining inside the pipes with outside zinc and bituminious coating . Rates are ex factory excluding transportation taxes and duties , Contractor Profit and overhead charges .

100 mm dia ( K-9 )

150 mm dia ( K-9 )

Providing and Supplying of ISI standard DI Specials and fittings with sealing rubber gasket of SBR complete with cast iron follower gland & MS Nuts bolts coated or otherwise protected from rusting and suitable for DI Pipes complete as per IS : 9523 class K -12. Note : The Rates are F.O.R at Worksite in jharkhand inclusive of royalty , inspection charges and other taxes but exclusive of GST & CP .

Socketed

100 -150 mm dia

Providing and Supplying in standard lengths High Density Polyethylene Pipe ( HDPE Pipe ) of SUPREME/ FINOLEX/ LAXMI ENGITECH brand Conforming to IS : 4984 / 14151 / 12786 / 13488 ( Latest Revision with necessary jointing materials like mechanical connectors i.e thread / insert joint / quick release coupler joint / compression fitting joint or flanged joints excluding couplers / specials and taxes ) Note : The Rates are F.O.R at worksite in jharkhand including royalty , inspection charges and other taxes but excluding GST & CP .

HDPE Pipe of Materials Grade PE -80 , PN -6 ( dia in mm )

32 mm dia

40 mm dia

50 mm dia

63 mm dia

75 mm dia

90 mm dia

110 mm dia

Providing and Supplying ISI marked Cast Iron Double Flanged reflux valves ( non return valves ) of following dia inspection charges unloading from railway wagon, loading into truck transportation up to department stores / site unloading stacking etc . complete reflux valve as per IS : 5312 Part 1 ( 1984 )

with byepass arrangements - PN : 1.6

80 mm dia

100 mm dia

Providing double flange sluice valve conforming for IS : 2906 / 14846 including worn gear arrangements as per test pressure stainless steel spindle , caps transportation etc all complete .

with byepass arrangements - PN : 1.6

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing and Supplying in standard lengths High Density Polyethylene Pipe ( HDPE Pipe ) of SUPREME/ FINOLEX/ LAXMI ENGITECH brand Conforming to IS : 4984 / 14151 / 12786 / 13488 ( Latest Revision with necessary jointing materials like mechanical connectors i.e thread / insert joint / quick release coupler joint / compression fitting joint or flanged joints excluding couplers / specials and taxes ) Note : The Rates are F.O.R at worksite in jharkhand including royalty , inspection charges and other taxes but excluding GST & CP .

HDPE Pipe of Materials Grade PE -80 , PN -6 ( dia in mm )

160 mm dia

200 mm dia

250 mm dia

315 mm dia

400 mm dia

450 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand :10 graded stone aggregate 40 mm nominal size) up to haunches of S.W.pipes including bed concrete as per standard design :

150 mm dia

200 mm dia

250 mm dia

300 mm dia

Providing and fixing square-mouth S.W. gully trap grade 'A" complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 Kg as per standard design :

180x150 mm size P type

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra Depth For Manhole

Size 90x80 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra Depth For Manhole

Size 90x120 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS:1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering esides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per pecifications and having manufacture’s permanent identification mark to be visible even after fixing,including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

TOTAL SCHEDULE ITEMS

Non Schedule Items

Granite work gang saw cut (polished and machine cut) of thickness 18mm for wall lining,skirting and dado (veneer work) in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade: (To be secured to the backing by means of cramps, which shall be paid for separately).

Providing and applying special pure acrylic base resin stone texture paint ( finish thickness 1.2mm to 1.5 mm) Marmoplast of Ultratech make or equivalent . One coat of acrylic Primer Mixed with wall sealer in the ratio of 1:1 is applied with brush and roller. Repairs to be done with interior grade putty post primer application . One Coat of stone crushed texture to be applied as pitted finish applied with special tool (added with inorganic pigments from 0.01- 3.00%) after the final texture coat one coat of pure acrylic emulsion followed by final coat of siloxane base protection coat to be applied which make the product completely water repellent / dust resistant / antifungal which ensures with a warranty of 08 years on shades and sustainability ,whereas grooves are to be crafted in plaster as design approved by engineering in charge.

Providing and fixing C.P. brass Double coat hooks fixed in Toilet wall with C.P brass wall flanges & C.P. brass screws and other required accessories complete in all respect as per direction of engineer - in - charge .

Providing and fixing health faucet with 1 m CP brass flexible tube and swivel hook with CP brass wall flange including cutting & making good the walls wherever required complete in all respect as per direction of engineer in charge .

Providing and fixing stainless steel 600 mm long Grab Bar with 2 nos CP brass wall flange including cutting & making good the walls wherever required complete in all respect as per direction of engineer - in - charge .

Providing & fixing C.P. brass Central hole wall mounted / table mounted sink mixer / Lab sink mixer with aerator connecting legs & 2 nos CP brass wall flange and 2 nos CP brass stop cock including cutting & making good the walls wherever required complete in all respect as per direction of engineer - in - charge .

Providing and fixing vertical or horizontal storage type hot water heater fixed to wall with anchor bolts & nuts, 15mm CP brass angle stop cock and 15mm CP brass non-return valve complete including making connections with 15mm dia CP connecting pipes on inlet and outlet, suitable length of power cable and 15 amps plug .

15 Litre Capacity

25 Litre Capacity

Providing & Fixing water purifier cum water cooler made of stainless steel having storage capacity of 80 liter & cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge .

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable including Supplying and fixing brass batten/ angle holder connection etc. as required.

Supply, installation, testing and commissioning of 3 MP Dome Camera , ONVIF profile S & G ,UL , CE , FCC Certified , 1/2.8" CMOS sensor ,3.6 mm fixed focal , triple stream ,Min Illumination :0.01 Lux @ (F1.2, AGC ON), 0.028 Lux @(F2.0, AGC ON), 0 Lux with IR , Shutter Speed : 1/5 ̴ 1/100,000 s , Edge analytics : line crossing , perimeter intrusion , stationary object ,Video Compression : H.265 ,H.264 , frame rate 30 fps @ 3MP , Edge analytics : line crossing , perimeter intrusion ,Face detection , cross counting , stationary object ,Inbuilt IR LED , IR distance upto 30 mtrs ,IP 66 , POE .

Supply, installation, testing and commissioning of UL Listed 3 MP Bullet Camera , ONVIF profile S & G ,UL , CE ,FCC Certified , 1/2.8" CMOS sensor ,3.6 mm fixed focal , triple stream , Min Illumination :0.05 Lux @ (F1.2, AGC ON), 0 Lux with IR , Shutter Speed : 1/5 ̴ 1/100,000 s , Video Compression : H.265 , H.264 , frame rate 30 fps @ 3MP , Edge analytics : line crossing , perimeter intrusion ,Face detection , cross counting , stationary object ,Inbuilt IR LED , IR distance upto 30 mtrs ,IP 66 , POE .

Supply, installation, testing and commissioning of ONVIF profile S & G ,UL certified 16 Channel NVR , 4 SATA ports , each SATA capacity of upto 8 TB , Recording Bandwidth 320 Mbps , 1 X HDMI , 1 X VGA , Alarm : 16ch in / 1ch out , 1 X RJ45 port , 1x3.0 USB for backup / upgrade, 2x 2.0 USB for mouse , Smart Phone support : iOS, Android

Supplying ,Installation, Testing and commissioning of 8TB HDD for Storage.

Supply, Installation, Testing & Commissioning of 8 port 10/100/1000 + 2 X gigabit SFP , managed L-2 Switch with SFP module switching capacity 216 gbps, Complete as per side required.

Supply, installation, testing and commissioning of Client workstation with Min-intel i7 or better , 8 GB RAM , 4 GB dedicated graphic card , 1TB HDD , 1 x HDMI Port.

Supplying ,Installation, Testing and commissioning of 42” Full HD LED Display Unit - Wall Mount.

Supplying ,Installation, Testing and commissioning of HDMI Cable- 3Mtr

Supply, Installation, Testing and commissioning of 32U Rack - Outdoor with PDU,FAN and Cable Manager(Wallmount).

Supply , Installtion , Testing and comissioning of armoured 6 core Singlemode OFC cable for interfloor switch connectivity.

Supply , Installtion , Testing and comissioning of 12 port loaded LIU with adaptor plates , pigtel cables for connections.

Supply , Installtion , Testing and comissioning of LC-LC singlemode fiber patch cord.

Supply , Installtion , Testing and comissioning of CAT6 information outlet (I/O) for Data, Voice, CCTV & Wi-Fi rack.

Supply , Installtion , Testing and comissioning of loaded 12 port CAT6 jack panel for CAT6 cable termination.

Supply , Installtion , Testing and comissioning of CAT6 patch cord 3 feet for rack side switch termination for user End.

Supply , Installtion , Testing and comissioning of CAT6 patch cord 7 feet for user termination to information outlet Rack End.

Supply , Installtion , Testing and comissioning of 12 U Wall mount rack with fans , 2 Nos of hardware pkts.

Supply, installation, testing and commissioning of Single Mode 1G SFP Module compatible with above switches.

SITC of Analog telephone instrument with CLI facilities, flash, redial .

11 KV HT DP STRUCTURE

Supply, Installation, testing and commissioning of 11 KV DP structure as per CEI & HPSEB norms & comprising of the following, but not limited to it for completion of works

RSJ pole of 9.15 mt length of size 175 x 90 mm complete with suitable M.S. base plate welded at bottombase plate - 2 Nos.

MS Channel of size 100 x 50 mm, length 4 mts (approx)

11 KV AB switch - 1 set

11 KV Horn Gap fuse Unit - 1 set

11 KV Lightning Arrestor

11 KV Disc insulator

11 KV Pin insulator

6 SWG copper wire for jumpering

Supply and erection of Stay set complete with necessary foundation, excavation and refilling of earth etc. as required.

Concrete foundation for RSJ poles burrioed upto a depth of 1830 mm in ground in a pit of size 450X450 mm in CC 1:3:6 along with 200 mm copping above ground inclusive of earth work.

Necessary Nut, Bolts, clamps, operating handle for AB switch, clamping welding etc. complete as required.

Painting the RSJ poles complete with two coat of Red Oxide and two coats of GI enamel paints complete as required.

Transpotation of all materials and accessories at site

Complete erection, testing and commissioning.

11KV H.T. METERING PANEL (INDOOR TYPE):

Supply, Receiving, Unloading, Storing, Shifting, Installation, Testing & Commissioning of indoor type floor mounted, dust, damp and vermin proof, cubicle HT. Metering Panel of SIEMENS/ SCHNIEDER/ AARNAV POWERTECH made out of 14 gauge CRCA sheet steel complete with 5 Amp electronic trivector meter, C.T.'s of 30/5 Amp, 0.5 Class, 10 VA Burden, and P.T's of 11 KV / √3, 110V / √3, 100 VA conforming to relevant IS Standards and complete as required. H.T. Metering cubicle along with C.T.'s, P.T.'s and trivector meter shall be got tested and approved from local electricity supply authority. The GA drawing shall be got approved by HPSEB/ local statutory authorities before fabrication.

11 KV HT SWITCHBOARD ( SINGLE PANEL) - INDOOR DUTY (TO BE LOCATED NEAR THE MAIN ENTRANCE)

Design, Manufacture, Supply, delivery, erection, testing and commissioning of a single enclosed 2 mm thick sheet steel clad floor mounting, vermin proof, fully interlocked vertical isolation, extensible, horizontal draw out, air insulated, metal clad switchboard having double isolation features complete with circuits as detailed below. The switchboard shall be complete with necessary PVC insulated copper busbars, small wiring, labels, cable eyes, cable termination to receive XLPE cables, foundation bolts and suitable for operation on 11 kV 3 phase, 50 cycle, earthed system with a rupturing capacity of 350 MVA at 11 kV Panel shall be equipped with following accessories and as per specifications and schematic drawing.

1No. - Metal Clad housing with having 630A Vaccum circuit breaker with Electric operated mechanism (spring charged motor - 230V AC)

1Set- Tripping coil & closing Coil 24V DC

1 - Set of isolating plug and receptacle

1 - Set of Automatic safety shutter

1- Set of breaker control switch (TNC)

1 set - Dual Core Cast Resin Current transformers of ratio 30/5A Class 5P10 and Class 0.5, 15 VA burden for protection & metering.

1set of 11/ √3KV / 110/√3 Volt, 100 VA burden & accuracy class 1, 3 nos. single phase construction, dry type cast resin PT

1 - Set of ON/OFF/Trip/ Spring Charged & Trip circuit healthy and phase indicating lamps.

1 No.- H.T. Cable joint box for 3C x 240 Sq.mm aluminium conductor XLPE cable,11 KV(E)

1- set of IDMT relay with 2 element of O/C protection(50%-200%) & 1 element of E/F protection (20%-80%).

1 no. Anti Pumping Relay

1 Set of Power Pack 220 Volt A.C. / 24 Volt D.C. complete as required.

Supplying,Installation,Testing & Commissioning Rate for 11 kV HT Panel as described above

Supply, erection, testing and commissioning of 230V, single phase 2 wire AC to 24V DC Batteries charger with semiconductor/IGBT fullwave rectifier with auto /manual float cum boost facility complete with 24V DC, 120 AH sealed maintenance free batteries including one no. distribution board having 63 Amps DP MCCB as incomer and 12 Nos. 20/16A DP MCB's (D.C. duty) as outgoing complete as required and as directed by Engineer Incharge.

DISTRIBUTION TRANSFORMERS

Supplying, installing, testing & commissioning of 250 kVA 11000/433 volts Deta/Star, vector group DY11, outdoor mounting,Oil Type Outdoor Transformer of ABB/ AREVA/ SCHNEIDER/ AARNAV POWERTEH with copper winding having a continuous rating of following capacity, 11 KV / 433 V, 3 Phase, 50 Hz, having bushing on HV side suitable for 11 KV XLPE cable & on 433 Volt L.V. side suitable for 2 Nos 3.5C X 300 Sq mm XLPE Cable.The Transformer shall have off load tap changing links on HV side, for +5.0% to -5.0% in steps of 1.25% . It shall also have Earthing Terminal, Lifting hooks, base channels skid type suitable for mounting on floor and plinth. to IS:1180 EEL II (Revised in July 2017), IEC 60726 & IS 2026, ECBC-2017, ANSI, NEMA standards & as per specification complete in all respects as required at site.

The Following Fittings Shall Be provided with all required accessories:- Rating & Terminal Marking Plate, Earthing Terminals, Lifting Lugs For Main Tank & Top Cover, Filter Valve , Drain Cum Sampling Valve, Thermometer Pocket, Dial Type Oil Temperature Indicator, Air Release Plug, Silica Gel Breather, oil conservator, Explosion Vent, Inspection Cover, Arcing Horn, Radiators Mounted on Tank, 4 Nos. uni-directional Rollers, First Filling of Transformer Oil as per IS:335, Magnetic Oil Level Gauge, Marshalling Box, Epoxy Bushing, PU Paints, Palm, LV Bus Bar, Radiator Valves, Cable Box on LT side & Cable Box on HT side. Transformer shall Compliance to IS:1180 & IS:2026 all parts latest as on date whichever is higher. complete with all accessories

The transformer shall be delivered along with after complete factory tests and temprature rise test, Operational & Maintenance manual and test certificate of unconditional guaranteed against manufacturing defects for a period of 18 months from the date of supply.

Transformer described as above.

Supplying of following size of aluminum conductor, XLPE insulated armoured and over all PVC sheathed, 11 KV (E) grade earthed cable as per relevant IS code and technical specifications

3C x 240 sq.mm. XLPE insulated Aluminium. Armored. Cable

Supply of fire buckets 4 No. in each set duly filled with fine sand and fixed on an angle iron frame as per requirement of local authorities. Fire buckets shall be painted red from outside and white from inside with additional handle at the bottom and suitable for outdoor installation.

Supply and fixing on position the approved Single Line Diagram framed in 1000 x 800 mm size glass frame and installed in main switch room as directed by Engineer Incharge

Supply of First Aid box as directed by Engineer Incharge

Supply of tool kit with 1 pair 11 KV rubber hand gloves as directed by Engineer Incharge.

Supplying & fixing standard shock treatment charts in English & Hindi duly framed and covered with glass as directed by Engineer Incharge.

Providing Safety mat made of elastomeric polymers Material (Class B) 1.2 M wide with thickness 2.5 mm to withstand 35KV dielectric strength AS PER relevant IS Code

Providing a mat made of elastomeric polymers Material (Class A )1.2 M wide with 2 mm thickness to withstand 1.1 KV dielectric strength AS PER relevant IS Code

Supply, installation, testing and commissioning of exhaust pipe fabricated out of 6 mm thick MS pipe Class C Heavy duty conforming to IS:3589 with all fixing accessories and hardwares.The work include necessary cladding of exhaust pipe work using 50 mm thick Loosely bound resin (LBR) mattress/ mineral wool/ Rockwool, density not less than 120 kg/m3 and aluminium cladding (0.6 mm thick) for the complete portion. The exhaust pipe work includes necessary supports, foundation etc. to avoid any load & stress on turbo charger / exhaust piping.The exhaust pipe shall be run along the existing wall of the building duly clamped/supported on independent structure for which, the design and Drawing for such structure shall be got approved from the Engineer-in-charge.

100 mm dia

Design, supply, fabrication and erection of steel structure from channel /angle iron of suitable sizes to support the chimney /exhaust MS pipe duly taking into consideration of the wind load/pressure at the site etc. including the cost of civil foundations as required to support a maximum of 2 nos exhaust chimneys on the overhead platform complete as required. The structure shall be given primer coat and two coats of enamel painting.

SS Flexible Bellow 100 mm dia

Aluminium cladding for the residential silencers

Supply & Fixing of Y Bend for Exhaust pipe

Supply, installation, Testing and commissioning of the following rating UPS as per specifications and complete in all respects.

20 KVA online UPS three phase input and three phase output power system of input,Voltage range 360 to 485V AC , Frequency range 50 Hz +10% frequency range, output voltage range 415 V +1% , Power factor 0.8/3:1, harmonic distortion < 2% THD (linear load) : 5 % THD (non linear load) including Batteries for minimum 30 minutes backup time at full load, it's MS Rack Black powder coated/painted, connecting mylar cables, terminations,connections of UPS to batteries etc complete in all respect and as per direction of Engineer in Charge.

Each UPS unit shall have a unit rating of 20 kVA and shall comprise the following components, described below in this specification:

a. PFC rectifier

b. Battery charger

d. VRLA Battery

e. User and communications interface

f. User friendly front panel

g. Integrated Backfeed Protection

h. Each UPS must have inbuilt input isolator, output isolator and inbuilt manual bypass switch with in the ups cabinet

i. UPS should have inbuilt isolation transformer at I/P Side.

(for active redundancy configuration)

a. Static bypass (via a static switch) for each UPS unit

b. Manual maintenance bypass for each UPS unit

( other requirements)

a. User and communications interface

b. Battery management system

c. Any and all other devices required for safe operation and maintenance, including circuit breakers, switches, etc.

Complete UPS Set as mentioned above complete in all respect

Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 55 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks with sleeved TPN Aluminum Bus bars and GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade (RAL 7032) over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. This main panel must be extendable for future requirement in such a manner not to disrupt ongoing services at the point of use during extension. All LT Panel shall conform to latest IS/IEC -61439 code. All Panel shall be complete with power & control wiring, danger & inscription plate, Lifting hooks etc.

Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA.

All the MCCB with adustable overload, short circuit & earth fault protection and above shall have microprocessor. The panel shall be manufactured as per BOQ, tech specification and drawing.

NOTE: PANEL MUST BE AS PER IEC 61439 TYPE TESTED FROM ANY INDIA BASED TEST LABORATORY (CPRI/ERDA ETC) FOR ROTECTION AGAINST SHORT CIRCUIT/TEMPERATURE RISE/INTERNAL ARC/DEGREE OF PROTECTION) (PTTA PANEL UPTO 630A & TTA PANEL ABOVE 630A)

MAIN LT PANEL

INCOMER FROM TRANSFORMER 1 (1 Nos. 250 KVA)

1 Nos. 400A 4P MCCB, 36 kA breaking capacity with Microprocessor release and rotatry handle.

1 No. 400A FP suitable rating Contactor with all required accessories.

METERING & INDICATION

1 sets of R,Y,B phase indicating lamps each with 3 nos. 2A SP MCBs.

1 sets of Phase sequence Relay.

1 Set- of ON/OFF/Trip/ Spring Charged & Trip circuit healthy indicating lamps.

Surge protection device , Type 1, spark gap type for 10/350us wave, 3 Nos phase to neutral, one No neutral to earth ,(minimum 3+1 mode) with minimum discharge capacity 50KA along with necessary fuses - Model AG 50/440 T1 (Argos) or equivalent, 1 Nos.

1 Nos. servo bypass in main LT Panel, for bypass the incoming supply in case of any fault or maintenance in Servo Stabilizer.

INCOMER FROM DG SET-1 (1 Nos. 100 KVA )

1 No. 400A 4P MCCB, 25 kA breaking capacity with thermal release and rotatry handle.

1 No. 400A FP suitable rating Contactor with all required accessories.

METERING & INDICATION

1 set of R,Y,B phase indicating lamps each with 3 nos. 2A SP MCBs.

1Set- of ON/OFF/Trip/ Spring Charged & Trip circuit healthy indicating lamps.

BUS-BAR

1 Sets of 400A TPN Aluminium Bus Bar with colour coded PVC Sleeves

BUS-COUPLER

1 Nos. 400A FP Contactor with all required accessories.

1 no. 32-bit microprocessor based PLC with MMI for electrically & mechanically interlocking & auto load Management of DG Sets.

OUTGOINGS

3 Nos. 250 A TPN MCCB, 25 kA breaking capacity with thermal release and adjustable setting and with rotary handle (For HVAC Panel-1 & 2, PV Solar System, Plumbing Panel and 2 Nos. Spare )

2 No. 200 A TPN MCCB, 25 kA breaking capacity with thermal release and adjustable setting and with rotary handle. (For MDB Light & Power Panel)

3 Nos. 100 A TPN MCCB, 25 kA breaking capacity with thermal release and adjustable setting and with rotary handle. (For Capacitor Panels)

3 Nos. 63 A TPN MCCB, 15 kA breaking capacity with thermal release and adjustable setting and with rotary handle (For Lift, Swimming Pool Panel, External Lighting Panel and 2Nos. Spare)

2 Nos. 40 A TPN MCCB, 15 kA breaking capacity with thermal release and adjustable setting and with rotary handle (For 2 Nos. Spare)

3 No. 40 A SPN MCB, 10 kA breaking capacity (For Guard Room DB & Servant Room DB )

3 Nos. 10 HP Star Delta Starter with 40A TP, MCCB (for Borewell pump- 1 & 2 and STP).

Supplying,Receiving, fixing, testing & commissioning of above described Panel

Wiring and Supplying , installation of space heater, humidistat and control MCB's shall be provided all vertical sections.

All Bus bar section/ backside panels have pad locking facility and hinged type door

5 W LED Lamp, switch shall be provided in each vertical section

Supplying,Receiving, fixing, testing & commissioning of Main LT Panel as described above

Note: Incomers for Transformer & Bus couplers shall be electrically & mechanically interlocked.

Note:The Main LT Panel shall also include the following:

(i) Necessary control and firing card with proper control wiring and lugs of the required rating to be provided.

(ii) Heavy duty exhaust fans to be provided for cooling

(iii) Each Incommer shall have Surge Protection Device.

(iv) All outgoing feeders of Main LT Panel shall have BMS compatible Electronic Energy Meter and ON/OFF/TRIP indication Lamps

Capacitor Panel -1 ( 80 KVAR)

INCOMER

1 No. 250 A TPN MCCB, 35 kA breaking capacity with thermal release and adjustable setting and with rotary handle. with ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with Control SP MCB

METERING & INDICATION

1 set of phase indicating lamps

1 No. 12 stage Microprocessor APFC controller/Relay shall continuously monitor all three phases and LCD displays for various Electrical Parameters like voltage, input current, capacitive current, KVA demand,KW, Power Factor, self diagnostic error code indication with printout facility of the above with RS 232 C port. Controller should mounted on the front side of the panel. Panel shall be suitable for Auto/Manual operation and shall be provided as per technical specifications.

BUS-BAR

1 Set of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

1 Nos.of 80A TP MCCB with suitable Capacitor duty contactor

2 Nos.of 40A TP MCCB with suitable Capacitor duty contactor

3 Nos.of 32A TP MCCB with suitable Capacitor duty contactor

1 Nos. 25 KVAR capacitor Bank each with 7% harmonic & discharge resistor suitable capacity to carry expected current continuosly. with suitable size capacitor duty contactor, start/stop Push buttons, ON/OFF indication Lamps, Auto/ manual switch complete with wiring in all respects.

2 Nos. 12.5 KVAR capacitor Bank each with 7% harmonic & discharge resistor suitable capacity to carry expected current continuosly. with suitable size capacitor duty contactor, start/stop Push buttons, ON/OFF indication Lamps, Auto/ manual switch complete with wiring in all respects.

3 Nos. 10 KVAR capacitor Bank each with 7% harmonic & discharge resistor suitable capacity to carry expected current continuosly. with suitable size capacitor duty contactor, start/stop Push buttons, ON/OFF indication Lamps, Auto/ manual switch complete with wiring in all respects.

Supplying,Receiving, fixing, testing & commissioning of Capacitor Panel as described above

Note: The capacitos shall also stipulate the following

(i) All the capacitors shall be suitable for 525 V

(ii) Necessary control and fixing card with proper wiring and lugs of the required rating to be provided.

(iii) Suitable exhaust fans, ventilation louvers to be provided for cooling.

(iv) LED indication lamps for number of capacito banks ' ON & Power Factor lagging or leading.

(v) The APFC shall be protected from following

* Over- voltage& Voltage unbalance

* Over temperature-system should be in standby mode and automatically restart after above condition restored.

*Total harmonic Distortion

MDB UPS Input Panel ( FOR SOLAR )

INCOMER

1 No. 100A 4P MCCB ,25 kA breaking capacity with thermal release and adjustable setting and with rotary handle.with ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 set of ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

BUS-BAR

1 Set of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

2 Nos. 63A TPN MCCB, 25 kA breaking capacity with microprocessor release and adjustable setting and with rotary handle.

Supplying,Receiving, fixing, testing & commissioning of above described Panel

SDB Lift Panel -1

INCOMER

1 No. 63A 4P MCCB ,25 kA breaking capacity with microprocessor release and adjustable setting and with rotary handle.with ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 set of ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

BUS-BAR

1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

2 Nos. 40A TPN MCCB, 25 kA breaking capacity with thermal release and adjustable setting and with rotary handle.

1 Nos. 40A SPN MCB ,10 kA breaking capacity

Supplying,Receiving, fixing, testing & commissioning of above described Panel

MDB Ventilation Panel -1

INCOMER

1 No. 100A 4P MCCB ,25 kA breaking capacity with thermal release and adjustable setting and with rotary handle.with ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 set of ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

BUS-BAR

1 Set of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

2 Nos.63A TPN MCCB, 25 kA breaking capacity with thermal release and adjustable setting and with rotary handle

1 No. 63A TPN MCB

NOTE :- All starters shall have ON & OFF push button & suitable rating of contractor and overload relays

Supplying,Receiving, fixing, testing & commissioning of above described Panel

Plumbing Panel (Pump Room)

INCOMER

1 No. 63A 4P MCCB ,25 kA breaking capacity with thermal release and adjustable setting and with rotary handle.with ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 set of ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

BUS-BAR

1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

2 Nos. 10 HP Star Delta Starter with 40A TP MCB (Borewell Pumps-1,2 )

2 Nos. 2 HP DOL Starter with 16A TP MCB (Filter Feed Pump- 1W+1S)

2 Nos. 3 HP DOL Starter with 10A TP MCB (STP Make Up Pump- 1W+1S)

2 Nos. 6 HP Star Delta Starter with 32A TP MCB (Domestic Water Supply Pump- 1W+1S)

2 Nos. 3HP DOL Starter with 10A TP MCB (Drainage Sump Pump- 2W+2S)

1 Nos 0.5HP DOL Starter with 16A SPN MCB (Chemical Doser- 1W)

2 No. 40A TPN MCB

1 No. 16A TPN MCB

2 Nos. 10A TPN MCB

1 No. 16A SPN MCB

NOTE :- All starters shall have ON & OFF push button & suitable rating of contractor and overload relays

Supplying,Receiving, fixing, testing & commissioning of above described Panel

MDB PANEL -2

INCOMER

1No. 250 A FP MCCB, 36 kA breaking capacity with Thermal release and rotatry handle.

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB

1 No. (0-250A) Ammeter with ASS with 3 nos. 250/5A CT's

BUS-BAR

1 Set of 300 A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

3 Nos.63A TPN MCCB, 25 kA breaking capacity with thermal release and adjustable setting and with rotary handle

3 Nos. 63A TPN MCB, 15 kA breaking capacity .

2 Nos. 40A TPN MCB, 10kA breaking capacity .

2 Nos. 40A SPN MCB, 10 kA breaking capacity.

2 Nos. 25A SPN MCB, 10 kA breaking capacity.

Supplying,Receiving, fixing, testing & commissioning of above described Panel

STP Panel

INCOMER

1 No. 100A 4P MCCB ,25 kA breaking capacity with thermal release and adjustable setting and with rotary handle.with ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 set of ON/OFF/TRIP indication Lamps, MFM with Communication Facility along with control SP MCB

BUS-BAR

1 Set of 125A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

2 Nos. 2 HP DOL Starter with 10A TP MCB (Raw Sewage Relift Pumps- 1W+1S)

2 Nos. 1 HP DOL Starter with 10A TP MCB (Sludge Recirculation Pumps- 1W+1S)

2 Nos. 1.5 HP DOL Starter with 10A TP MCB (Plant Room Sump Pumps- 1W+1S)

2 Nos. 2 HP DOL Starter with 10A TP MCB (Sludge Loading Pumps- 1W+1S)

2 Nos. 10 HP DOL Starter with 40A TP MCB (Air Blowers- 1W+1S)

1 No. 3 HP DOL Starter with 10A TP MCB (Centrifugal Pump)

2 Nos. 3 HP DOL Starter with 16A TP MCB (Filter Feed Pumps- 1W+1S)

2 Nos. 2 HP DOL Starter with 16A TP MCB (Softner Feed Pumps- 1W+1S)

2 Nos. 10 HP Star Delta Starter with 40A TP MCB (Flushing Water Transfer Pump- 1W+1S)

2 Nos. 3 HP DOL Starter with 16A TP MCB (Irrigation Water Pumps- 1W+1S)

1 No. 0.5 HP DOL Starter with 16A DP MCB (Chemical Dozer- 1W)

1 No. 3 HP DOL Starter with 10A TP MCB (UV System)

1 No. 40A TPN MCB

1 No. 16A TPN MCB

4 Nos. 10A TPN MCB

1 No. 16A SPN MCB

NOTE :- All starters shall have ON & OFF push button & suitable rating of contractor and overload relays

Supplying,Receiving, fixing, testing & commissioning of above described Panel

EXTERNAL LIGHTING FEEDER PILLAR-1 (Outdoor Type weather proof, double door with canopy IP-65)

INCOMER

1No. 63A FP MCB(10 KA)

1No. 63A FP Contactor, AOM switch & Astronomical Watch Timers for 24 Hrs. setting

Metering & Indication

1 set of RYB phase indicating lamps

Surge Protection Device Type2 Class C 4 Mode Imax 15KA Per Pole With Necessary Protection .

BUS-BAR

1 Set of 100A TPN Copper Bus Bar with colour coded PVC Sleeves

OUTGOINGS

4 Nos. 20A FP MCB

4 Nos. 20A DP MCB

Supplying,Receiving, fixing, testing & commissioning of above described Panel

Supply of following sizes of XLPE insulated Aluminum conductor strip/ wire Armoured, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS-7098 Code and technical specifications.

3 x 2.5 sq. mm

4 x 4 sq. mm

4 x 10 sq. mm

4 x 16 sq. mm

4 x 25 sq. mm

3½ x 35 sq. mm

3½ x 50 sq. mm

3½ x 70 sq. mm

3½ x 95 sq. mm

3½ x 120 sq. mm

3½ x 150 sq. mm

3½ x 185 sq. mm

3½ x 240 sq. mm

3½ x 300 sq. mm

XLPE Insulated Copper Armoured Cables

3C x 6 Sq.mm.

3C x 4 Sq.mm.

7 C x 1.5 Sq.mm.

12 C x 2.5 Sq.mm.

1C X 35 sqmm Cu flexible(Unarmoured) cable

Supply and making End termination with brass Single/ Double compression gland including providing and crimping of aluminum/copper solderless lugs/ferrules for XLPE/PVC insulated armoured power aluminum/copper conductor cables 1.1 KV grade of following sizes:

SINGLE COMPRESSION GLAND FOR AI. AR. CABLE

4C/3C x 6/4 sq.mm.

Single Compression Gland for Cu. Cable

4C/3C/2C x 4/6/2.5 sq.mm.

7C x 1.5 Sq.mm.

12C x 2.5 Sq.mm.

Supply of long life Maintenance Free Earthing System . The Rod shall be of Copper Bonded Steel with 23.2 mm dia. and 10 feet length with a core of mild steel molecularly bonded with min. 250 microns coating of 99.99% pure electrolytic grade Copper and exothermically welded Cu Busbar of 50X6X200mm both tested by CPRI capable of bearing fault current of 50kA. Along with earth enhance compound tested by RoHs complying IEC 62561-7 in a sealed bag of minimum 30 kg (10 kg Bag x 3) resistivity is less than 0.12 ohm meter. . with Suitable Poly-plastic Pit Cover with lockable arrangement.

Supply of long life Maintenance Free Earthing System. The Rod shall be of Copper Bonded Steel with 17.2 mm dia. and 10 feet length with a core of mild steel molecularly bonded with min. 250 microns coating of 99.99% pure electrolytic grade Copper and exothermically welded Cu Busbar of 50X6X200mm both tested by CPRI capable of bearing fault current of 25 kA. Along with earth enhancement compound tested by RoHs complying IEC 62561-7 in a sealed bag of minimum 30 kg (10 kg Bag x 3) resistivity is less than 0.12 ohm meter . with Suitable Poly-plastic Pit Cover with lockable arrangement.

Supplying, fixing, testing and commissioning of following bare Copper/ GI flat including all necessary fixing accessories and effecting connections.

50 mm x 6 mm thick Cu flat

50 mm x 6 m thick GI flat

Supply and laying medium class GI pipe under road/paved areas/wall crossing etc. including earth excavations refilling, ramming and making good as approved.

150 mm dia GI pipe Class B

Supplying, fixing, testing and commissioning of following size PVC sleeve for bare Copper/GI tapes including all necessary fixing accessories and effecting connections.

For 50 mm x 6 mm thick Cu. tape.

Supply of Lightnig counter - LCD screen shows the number of lightning strikes, hour and date of lightning events Buttons enable TIME/DATE setting and log viewing. Replaceable battery, working life minimum five years, meet the requirements for IS/IEC 62305 and IEC 62561-2.Tested for Electrical ,Mechanical and Chemical as per IEC 62561.

Supply, installation,testing & commissioning of solar power system by solar photovoltaic panel of 20 KWp at roof of building also including inverter & provision for normal power connection in distribution panel as per manufacture specification and as required .(With battery)

Supplying, installation, testing and commissioning of Spyke light fitting suitable for 8 watt IP 65LED having system lumen output of minimum 750 lumens complete with all accessories and lamp. Wipro Cat No.: LF05-600-036-27-XX

Supplying, installation, testing and commissioning of 40W LED Solar Street Light On 7 Meter GI octagonal Pole having Compact, Aesthetic, Eco friendly & modern integrated Solar street light in extruted Aluminum construction with high efficiency monocrystalline silicon photo voltaic panel, high efficacy SMD LED 6500K having secondary lens optics for street lighting distribution, high performance lithium battery, MPPT charge controller & Intelligent control module/sensor with higher reliability, long service life, suitable for easy & quick installation. Wipro Cat No.:LR 14-591-XXX-65-XX.

Providing, installation of 200 x 150 x 125 mm polycarbonate weather proof (IP-55) junction box and SP MCB’s and terminal block. Supplying and laying cable through GI pipe upto junction box including excavation and back filling, wiring with 2 x 2.5 sq.mm PVC insulated 1100 volts grade copper conductor wires from junction box to lighting fixture complete.

Supplying , Installation , Testing and Commissioning of Electric Driven Terrace Pump Suitable for Automatic operation and Consisting of Following Complete in all Respect as Required ( Terrace Fire Pump )

Horizontal Type Multistage , Centrifugal Pump of Cast Iron Body and Bronze Impeller with Stainless Steel Shaft Mechanical Seal Conforming to IS : 1520

Suitable HP Squirrel cage Induction motor , TEFC , synchronous speed 1500 RPM , Suitable for operation on 415 Volts 3 Phase 50 Hz AC Supply with IP 68 protection for enclosure Horizontal Foot Mounted type with class F insulation Conforming to IS : 325 with Energy Efficiency class IE-3

MS Fabricated Common Base Plate Coupling , Coupling Guard Foundation bolts etc as Required

Suitable Cement Concrete Foundation duly Plastered with anti vibration Pads

450 Lpm at 35 m Head

Supplying and Fixing Air Vessel made of 450 mm dia 8 mm thick ms sheet 2000 mm in height with air release valve on top and flanged connection to riser drain arrangement with 25 mm dia gunmetal wheel valve with required accessories pressure gauge and painting with synthetic enamel paint of approved shade as required

Providing and fixing of Fire Hose Cabinet size not less than 2.1 x 1.2 x 0.90 mtr made out of M.S. sheet not less than 1.5 mm thick having central opening and 4 mm thick glazed glass doors (Two nos.) suitably marked on the outside 'with the letters "FIRE HOSE" including necessary locking arrangement and painting in PO red colour suitable to accommodate, internal hydrant valve, 2 nos 15 mtr long Hose pipe, branch pipe, nozzle and fire man's axe. It shall be fixed inside the FHC Cabinet Complete as required .

Providing and fixing standard firemans axe with heavy rubber handle.

Providing and fixing dial type pressure gauge with isolation cock and copper pipe on main header Dial diameter 100 mm celebration 0-16 / sq. cm.

Providing & fixing double flanged flexicon rubber expansion joint with unit control of standard length as per maufacturers specs. Tested to a pressure of 20 Kg/Sqcm including rubber gaskets, flanges, nuts, bolts and washers complete as required.

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing and fixing Fire Extinguishers (CO2 type powder ) 4.5 Kg Capacity complete with all accessories as per manufacturers specifications.

Providing and fixing Fire Extinguishers (A, B, C type powder ) 6 Kg Capacity complete with all accessories as per manufacturers specifications.

Providing and fixing Fire Extinguishers (A, B, C type powder ) 9 Kg Capacity complete with all accessories as per manufacturers specifications.

Providing and Fixing ISI marked (IS:2878) Fire and wall suspension bracket, Extinguisher, Trolley mounted carbon-dioxide type capacity 45 Kg. Flat base including valve, discharge hose of not less than 10mm dia 1m long complete in all respects including wheeled trolley, carrying handle and initial fill with CO2 gas as per IS: 307-1996 filled to a filling ratio of not more than 0.667.

Providing and Fixing ISI marked ( IS : 13386 ) fire extinguisher Mech. Foam type capacity 50 litres with gunmetal cap and nozzle, trolly mounted and complete in all respects including initial fill.

Constructing 2x1x1 mtr (effective Depth). inernal dimension brick masonry oil and grease trap with Ist class bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 mix (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size) inside and outside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement inside and rough plaster on outside, 2 Nos. 150 mm dia S W Tees, 3 Nos. 600x600 mm size SFRC manhole cover with frame, necessary baffle walls, 100 mm dia 2100 mm high SCI vent pipe with cowl, complete as per drawing, including excavation refilling and disposal of surplus earth.

Constructing 2x1x1 mtr (effective Depth). inernal dimension brick masonry Desilting Chamber with Ist class bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 mix (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size) inside and outside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement inside and rough plaster on outside, 2 Nos. 150 mm dia S W Tees, 3 Nos. 600x600 mm size SFRC manhole cover with frame, necessary baffle walls, 100 mm dia 2100 mm high SCI vent pipe with cowl, complete as per drawing, including excavation refilling and disposal of surplus earth.

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel-304 body, Stainless steel-304 impeller, Stainless steel-304 casing, shaft of Stainless steel-316 and C.I. base & head with mechanical seal, connected to a TEFC induction motor with class IE -3 efficiency and IP 68 Protection and class F insulation suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock,including suction and delivery headers of G.I "C" class pipe of required dia, isolation valves, NRV of PN-16 grade,required valve and strainer & vibration eliminators on both suction & delivery side of pumps, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information.

Filter Feed Pump ( In UGT / Plant Room )

Set of Two pumps (1 Working + 1 Standby)

Capacity - 200 LPM

Head - 30.0 Mtr.

Eff. - Class IE-3

Make up Pump ( In UGT / Plant Room )

Set of Two pumps (1 Working + 1 Standby)

Capacity - 200 LPM

Head - 60.0 Mtr.

Eff. - Class IE-3

Supply, installation, testing & commissioning of variable speed hydropneumatic system mounted on a common base plate comprising of vertical inline multistage pumping set with Stainless steel-304 body, Stainless steel-304 impeller, Stainless steel-304 casing, shaft of Stainless steel-316 and C.I. base & head with mechanical seal, shaft directly coupled to a TEFC induction motor with class IE -3 efficiency and IP 68 Protection and class F insulation suitable for 400/440 volts, 3 phase, 50 cycles AC supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation, one No. microprocessor based controller, two Nos. variable frequency drives, one No.remote sensors, transmitters, sequence running cotroller, dry running Protection,motor control centre, necessary power and control cabling from MCC to pumps including required rating of MCB, two Nos. required capacity M.S diaphragam tank with interchangeable butyl rubber membrane,complete in all respects including suction and delivery headers of G.I "C" class pipe of required dia, isolation valves, NRV of PN-16 grade & vibration eliminators on both suction & delivery side of pumps, power box, equipped with fuses/ isolators/circuit breakers as required.

No. and capacity of Pressure Vessel - 01 Nos. x 200 litres min. (Or as per Manufacturer Calculations)

The system shall also comprise the following:-

Type 8202 pressure transducer with SS pressure sensor and control electronic board. Output 4-20m A on two wires conforming BS-6134 standards and IP 68 protection class.

Domestic Water Supply Pump ( In UGT / Plant Room )

Set of Two pumps ( 1 Working + 1 Standby)

Capacity - 200 LPM

Head - 80.0 Mtr.

Eff. - Class IE-3

Supply, installing, testing and commissining of submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersible motor with class IE-3 efficiency and IP 68 Protection and class F insulation for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphram and bend, vertical discharge pipe, guide pipe and chain in built level controller, sequence running controller, dry running Protection with gunmetal isolation cock,including suction and delivery headers of G.I "C" class pipe of required dia, isolation valves, NRV of PN-16 grade,required valve and strainer & vibration eliminators on both suction & delivery side of pumps complete in all respects.

(Pumps shall be installed in a set of two pumps One working and One standby , Pump shall be automatic ON / OFF on Cyclic Pattern )

Drainage Sump Pumps

(Pumps to be suitable to handle solids upto 28 mm size)

Capacity - 250 LPM (Each)

Head - 15 M

Eff. - Class IE-3

Supply, installation, testing & commissioning of vertical self supporting filtration unit fabricated from MS sheet as per IS: 2825, (minimum thickness of shell 6mm and dished end 8mm) pressure gauges, sample cock, GI class 'C' face piping, CI butterfly valves and all accessories , with initial charge of filter media including anthracite, 600 mm depth of graded sand gravel and 600 mm depth of anthracite painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, testing and commissioning complete.

Dual Media Filter

Capacity- 12000 lph

Filtration rate - 15000 lph/sqm

Filter dia approx. - 1000 mm

Working pressure : 3.0 Kg/sq cm.

Test pressure : 4. 5 Kg/sq cm

Supply, installation, testing & commissioning of vertical self supporting filtration unit fabricated from MS sheet as per IS: 2825, (minimum thickness of shell 6mm and dished end 8mm) pressure gauges, sample cock, GI class 'C' face piping, CI butterfly valves and all accessories , with initial charge of filter media including anthracite, 600 mm depth of graded sand gravel and 600 mm depth of anthracite painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, testing and commissioning complete.

Activated Carbon Filter

Capacity- 12000 lph

Filtration rate - 12000 lph/sqm

Filter dia approx. - 1200 mm

Working pressure : 3.0 Kg/sq cm.

Test pressure : 4. 5 Kg/sq cm

Supply, installation, testing & commissioning of metering pump type chemical doser with motorize ajector, shaft & blade SS 304 material with 100 lits. PVC/HDPE solution tank, injection fitting assembly, suction and delivery hose upto the point of injection, capacity 0-6 lph, complete in all respects.

Supply, installation, testing & commissioning of annunciation and indication panel with interlocking arrangement complete in accordance to specification with level controller ( In Tubewells , Fire Water , Raw Water , Domestic Water Tank : High / Low Level Controller ) etc with control cabling from field to MCC as required .

The System shall be complete to ensure automatic operation of pump in accordance to water Level in respective tanks .

Providing and Fixing Level Controllers for water pumps to start / stop the pumps at set level including wiring , cabling from pump to panel and all other accessories as required to operate the system automatically .

Providing and Fixing Pressure Switch for Water Pumps to start / stop the pumps at set pressure including wiring , cabling from pump to panel and all other accessories as required to operate the system automatically .

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings conforming to IS : 1879 and clamps including MS pipe supports, painting with two or more coats of synthetic enamel paint including one coat of primer as per specification cutting and making good the walls etc. complete.

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing and fixing forged brass ball valve suitable for pressure 25 Kg/Cm2 of the following size including providing necessary union / flange.

32 mm dia

40 mm dia

Providing & fixing of C.I. butterfly valve suitable for pressure 16 Kg/Sqcm. with flanges, nut bolts & gaskets complete required.

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing & fixing cast iron Single Plate Check valves suitable for pressure 16 kg / sqcm complete with matching flanges, rubber insertion, nuts, bolts and washer complete as required etc. of following sizes.

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Providing & fixing double flanged flexicon rubber expansion joint with unit control of standard length as per maufacturers specs. Tested to a pressure of 16 Kg/Sqcm including rubber gaskets, flanges, nuts, bolts and washers complete as required.

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Providing and fixing C.I. 'POT' strainer with bronze perforated sheet basket tested to a pressure of 16 Kg/sqcm including rubber gasket, flanges, nuts, bolts and washers, complete as required.

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Complete Set including all Items as described above

Providing and fixing sound insulated Polyproplene piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 20 dBA as per DIN EN 1451 , DIN EN 752 , DIN 1986 -100 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe not more than 1.25gms/m3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring.

75 mm dia

110 mm dia

Providing and fixing sound insulated Polyproplene piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 20 dBA as per DIN EN 1451 , DIN EN 752 , DIN 1986 -100 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe not more than 1.25gms/m3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring.

32 mm dia

40 mm dia

50 mm dia

Providing and fixing PP white Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections (Mcalpine, UK).

110 mm inlet and 110 mm outlet

Providing & fixing in position Poloplast material floor drain including cost of cutting and making good the walls and floors wherever required.

110 mm inlet and 63 mm outlet

Providing and fixing Poloplast material Inlet fitting / Multi Floor Trap with maximum 3 inlets 32,40 or 50 mm size fabricated from 110 mm dia PP pipes and fixed to PP sockets,fixed to Poloplast floor trap with chemical sealent joint and set in cement concrete as per standard drawing complete.

Providing and fixing Poloplast material cleanout plug( Ceiling or Floor) with suitable insert keys for opening, male threaded joint with Poloplast socket fixed to Poloplast Pipe complete in all respects.

110 mm dia

Providing and fixing Stainless Steel Grade (304) grating with ring and Stainless steel anti cockroach basket and two SS screw including fixing to the floor with cement mortar.

Providing and fixing MS holder bat clamps / PVC Material pipe clip of approved design to pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc.

75 mm dia

110 mm dia

Providing and fixing Terminal Guard / Vent Cowl of Standard PP Material including fixing the Vent Cowl on the top of Vent / Soil and Waste Stack and Rain Water Pipes .

75 mm dia

110 mm dia

Providing and fixing Tee / Elbow of 90 degree angle fittings of Standard PP Material including fixing the Tee on suitable Location of Vent / Soil and Waste Stack and Rain Water Pipes .

75 mm dia

110 mm dia

Providing and fixing Tee / Elbow of 45 degree angle fittings of Standard PP Material including fixing the Tee on suitable Location of Vent / Soil and Waste Stack and Rain Water Pipes .

75 mm dia

110 mm dia

Providing and fixing Single / Double Socket of Standard PP Material including fixing the Bend on the Bottom of Vent / Soil and Waste Stack and Rain Water Pipes .

75 mm dia

110 mm dia

Providing and fixing Shoe Plain of Standard PP Material including fixing the Shoe on the Bottom of Vent / Soil and Waste Stack and Rain Water Pipes .

75 mm dia

110 mm dia

Providing and installing Air Admittance valves with required air flow rate, including submission of design data (Mcalpine )

Air flow Capacity up to 32 Litre per Second ( Maxi Vent )

Air flow Capacity up to 7.5 Litre per Second ( Mini Vent )

Providing and Fixing Maxi Filtra with Active Carbon Filters ( Studor )

100 mm Inlet and 110 mm Outlet

Providing and fixing Thermoflex or Careflex thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including all required accessories complete as per specification.

9 mm thick ( Pipes in Chases)

For 15 mm dia Pipe

For 20 mm dia Pipe

For 25 mm dia Pipe

Providing, fixing, testing and commissioning of motorised butterfly valve of following dia for filling of overhead water tank complete with high and low level control switches to control tanks. The level controllers shall be installed in overhead tanks. The level switch will close the valve when water level is high in overhead tank and open the valve when overhead water tank level is low. The system should be complete in all respects with accessories 220 V AC / 2 V DC, IP67 electrical water level control unit, copper control wiring in whether proof casing etc.

40 mm dia nominal bore

50 mm dia nominal bore

Supplying and placing of Lecture Table Durian Model Tomkins/Acombination Of Three Rows First , Middle And Last Chair & Desk Combination Sofa With Prealminated Particleboard Table Per Seat Size- 590mm X 375mm X 18mm Main Frame Mde Of Crca Powder Coated One Seater Desk Size Is Size:1090mm X830mm (Lxh) Unit Size:590mm(L) X 1090mm(D) X 830mm (H), * The Product By The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org". ". MAKE-DURIAN,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE MODEL NO- TOMKINS.WARRANTY-5 YEAR.

Supplying and placing of Dies table for Lecture Table, Desk Structure Of Rectangular Shape . Primary Work Surface Over All Size Is 1500mm(L)X 750mm(D)X 750mm(H) 18mm Thick Table Top Made Of Prelaminated Particle Board Work Surface With The Hot Melt Glue Used For Fixing The 2mm Thick Pvc Edge Banding Made Of Same Matte Finish, Wire Management Hole With Pvc Grooment On Table Top. * Construction Right + Left Side Table Top Based On A 18mm Thk Engineered Wood And From Down Side 1 + 1 Fixed Pedestal Attached With Modesty Both Pedestal Have A Same Construction 3 + 3 Drawers- Per Drawer Have * 1 + 1 Fixed Pedeatal,In Provided With Cetnral Lock For Security And Handles Are Provided For Easy Of Opening. Overall Construction Of Pedestal Is 18 Mm Along With Fecia Of Drawers. * Three Layer Prelaminated Particles Board(Wood Product) Of Grade Ii Type Iii Of Is 12823/Latest,* The Product By The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org". . MAKE-DURIAN,MODEL MAPLE MOLDING PVT.LTD.,BOMBAY SAFENO- RUSS.WARRANTY-5 YEAR.

Supplying and placing of Dies Chair for Lecture Table,* Medium Back 360° Degre Revolving Chair Sku : 70011/Mb/A , * All Over Size Is : 560mm(L)X 480mm(D)X 980mm(H) , *The Chair Made Of Full Fabric In Black Colour . It Will Comes In Matte Finsih In Contemporary Style . Details : * Arms : Fixed Arms P.P. Connected With Seat And Back . * Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat And Back) . * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Support * Mechanism : Centre Tilt Mechanism . * The Seat Size Is 475mm(L)X 490mm(D) & The Back Height Is @ 500 Seat Maximum Height Is 570mm & Minimum Height Is 470mm & Back Height From Floor Maximum Height Is 1080mm & Minimum Height Is 980mm * Gas Lift 100 Mm Telescopic Haudraulic * Base : 650mm Nylon Base With Smooth Castors . * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org",MAKE-DURIAN,MODEL NO MMPL/70011/MB,WARRANTY-5 YEARS.

Supplying and placing of Class Room Desk & Bench, (CLASS ROOM 1 TO 12),DESK SIZE:-1000MM (W) X 400MM (D) X 587MM (H) BENCH SIZE:- 1000MM (W) X 330MM (D) X 347MM /587MM(H) BACK PANNEL 620MM(L)X192MM(W) BACK PANNEL 620MM(L)X192MM(W), The top of the desk shall be made up of 18mm thick particle board of grade II as per IS 12823. • The shelf shall be made up of 18 mm thick particle board of grade II as per IS 12823 • Hooks should be provided on the vertical side frame on both side of the desk for hanging bags/bottles •The front of the desk shall be clad with modesty panel made up of Partical board • The seat and back shall be made up of 18mm thick particle board with PVC edges shall be sealed with 2mm thick PVC edge banding • The complete steel structure shall be welded with base pipe having cross-section area 25mm X 25mm and also be powder coated to the thickness 50-60µ thick.• All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal • * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org",MAKE-DURIAN,MODEL NO- NIMBLE/2.WARRANTY-5 YEAR.

Supplying and placing of Class room Teacher Table. Primary Work Surface Over All Size Is 1200mm(L)X 600mm(D)X 750mm(H) 25mm Thick Table Top Made Of Prelaminated Particle Board Work Surface With The Hot Melt Glue Used For Fixing The 2mm Thick Pvc Edge Banding Made Of Same Matte Finish, Wire Management Hole With Pvc Grooment On Table Top. *Right Side Below Table Top 2 Drawers, In Provided with Central Lock For Security And Handles Are Provided For Easy Of Opening. Overall Construction of Pedestal Is 18 Mm Along with Fecia Of Drawers. * Three Layer Prelaminated Particles Board(Wood Product) Of Grade Ii Type Iii Of Is 12823/Latest , Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE * The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark Compliant. The Bidder Should Either Offer Products Having Griha Compliance Or The Oem Should Have Fsc Certificate . The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of Class room Teacher Table. * Fix Cantilever Back Supported Powder Coated Fix Cantilever Frame Chair Sku : 70018/Cn, * All Over Size Is : 520mm(L)X 470mm(D)X 930mm(H) , *The Chair Made Of Full Fabric In Black Colour . It Will Comes In Matte Finsih In Contemporary Style . Details : * Arms : Fixed Armrest Padded Armrest. * Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat And Back) . * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Support * Only Seat Size Is 520mm(L)X 470mm(H) . Back Height Is @ 930mm * Fixed Cantilever Chair . * Base : M.S Powder Coated Tublar Frame Of Catilever Type . * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of Seminar Table,Desk Structure Of Rectangular Shape . Primary Work Surface Over All Size Is 1500mm(L)X 750mm(D)X 750mm(H) 18mm Thick Table Top Made Of Prelaminated Particle Board Work Surface With The Hot Melt Glue Used For Fixing The 2mm Thick Pvc Edge Banding Made Of Same Matte Finish, Wire Management Hole With Pvc Grooment On Table Top. * Construction Right + Left Side Table Top Based On A 18mm Thk Engineered Wood And From Down Side 1 + 1 Fixed Pedestal Attached With Modesty Both Pedestal Have A Same Construction 3 + 3 Drawers- Per Drawer Have * 1 + 1 Fixed Pedeatal,In Provided With Cetnral Lock For Security And Handles Are Provided For Easy Of Opening. Overall Construction Of Pedestal Is 18 Mm Along With Fecia Of Drawers. * Three Layer Prelaminated Particles Board(Wood Product) Of Grade Ii Type Iii Of Is 12823/Latest. * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of Class room Teacher Table. * Fix Cantilever Back Supported Powder Coated Fix Cantilever Frame Chair Sku : 70018/Cn, * All Over Size Is : 520mm(L)X 470mm(D)X 930mm(H) , *The Chair Made Of Full Fabric In Black Colour . It Will Comes In Matte Finsih In Contemporary Style . Details : * Arms : Fixed Armrest Padded Armrest. * Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat And Back) . * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Support * Only Seat Size Is 520mm(L)X 470mm(H) . Back Height Is @ 930mm * Fixed Cantilever Chair . * Base : M.S Powder Coated Tublar Frame Of Catilever Type . * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of Seminar Chair * Chair Sku : Diego/A/Cn/Standard, * All Over Size Is : 600mm(L)X 500mm(D)X 820mm(H) , *The Chair Made Of Full In Colour . It Will Comes In Finsih In Contemporary Style . Details : * Arms : Fixed Armrests With Full Writing Pad . * Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat And Back) . * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back * Base : 4 Legs Metal Powder Coated . * The Product ByDURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

* Supplying And Placing In Position Of Staff Room Table 14 Seater Of Size 2400mm X 900mm X 750mm, 25 Mm Thick Prelam Particle Board Tabletop With Machine Pressed Exposed Edges Shall Be Finished With 2 Mm Thick Pvc Edge Binding Tape Of Matching Colour And Shade Fixed With The Hot Melt Glue. Tabletop Supported With Powder Coated Slant Shape Metal Legs Of Size 50 Mm X 20 Mm And Connectors Of Size 40 Mm X 40 Mm Horizontal Connectors,0.8 Mm Thick Wire Management Hole With Pvc Grooment On Table Top, * Single Metal Powder Coated Raceway & "T" Riser Leg Wire Carrying Below Top For Wire Management, All Metallic Parts Should Be Epoxy Polyester Powder Coating To Thickness Of 50 Micron (Approx) . * Three Layer Prelaminated Particles Board (Wood Product) Of Grade Ii Type Iii Of Is 12823/Latest . Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE * The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark Compliant. The Bidder Should Either Offer Products Having Griha Compliance Or The Oem Should Have Fsc Certificate . The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org"

* Supplying And Placing In Position Of Staff Room Chair, * Low Back 360° Degre Revolving Chair Sku : 70020/Lb, * All Over Size Is : 625mm(L)X 450mm(D)X 920mm(H) , *The Chair Made Of Full Mesh In Black Colour . It Will Comes In Matte Finsih In Contemporary Style . Details : * Arms : Fixed Pp Armrest . * Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat). * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : Frame Of Design Shall Be Curved Made Of Two Pieces Injection Moulded Frame Cover With Mesh .Backrest Support Mesh Design Based On Symmetrical Lumbar Support * Mechanism : Syncro Single Locking Mechanism . * Only Seat Size Is 445mm(L)X 450mm(D)X 520-425mm(H) & The Back Size Is 625mm(L)X 480mm(H) , Seat Maximum Height Is 520mm & Minimum Height Is 425mm & Back Height From Floor Maximum Height Is 920mm & Minimum Height Is 820mm . * Gas Lift 100 Mm Telescopic Haudraulic * Base : 650mm Nylon Base With Smooth Castors . * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of Café Table,Made Of 25 mm Prelaminated Particle Board In Brown-Classic Walnut Crome Plated Led Color With Main Table Dia Size -1200mm X 750mm(H).* The Product By The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of Café Table,Made Of 25 mm Prelaminated Particle Board In Brown-Classic Walnut Crome Plated Led Color With Main Table, Table Size -1200mm(L)X 800mm(D)X 750mm(H).* The Product By The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of Cafe Chair In Color Also Avaible In Multi Colors With All Over Dimension Of Chair Is 381 Mm(L) X 419 Mm(D) X 839 Mm(H)* The Product By DURIAN,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of Lab table (Physics Lab,Biology Lab,Home Science) Size-(12'X4'X3') 600 mm Module with 2 Shutter 1 Drawer and 1 adjustable Shelf with Pedestal frame assembly and Auto Hinges, telescopic slidding channels and Lock fittings Hettich make, Pedestal 30mm 18SWG MS ERW Sq. Pipe make with level adjusting bolt epoxy powder coated,3-way water tap with Two fixed Bibs and 1 Swivel Type. brass make, ABS plastic knobs with color code with Epoxy Powder Coated,Double Sided Reagent Rack 2 tire without wiring and service fittings MS CRCA sheet 20g make with epoxy powder coating.Electric Socket 16 A / 6A 250 V AC.( N/W - Norisys ),MCB / Switch 16 A 240 V 50 Hz ( N/W - Norisys ),Island Bench Rear Cover MS CRCA 20g make with epoxy powder coating, Black Jet Granite Top - 17/18 mm, Total Sq. Meter,Sink-Cutout,Edge-Polishing,Silicon Sealant - Black,Silicon Sealant -White,Masking Tape, GI Nut Bolt with washer,Flexible R/w Pipe Both Side Fitting,Flexible R/W drain Pipe Fitting.* The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".DWS/LAB/005

Providing & Placing of Revolving Stool with MS Tubular four leg construction with MS foot rest ring duly epoxy powder coated. Top made up of SS finish. Adjustable Revolving top with height adjustment with MS screw mechanism.* The Product By The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".DWS/STOOL8001

Supplying And Placing In Position of Library Table 8 Seater Of Size 2400mm X 900mm X 750mm, 25 Mm Thick Prelam Particle Board Tabletop With Machine Pressed Exposed Edges Shall Be Finished With 2 Mm Thick Pvc Edge Binding Tape Of Matching Colour And Shade Fixed With The Hot Melt Glue. Tabletop Supported With Powder Coated Slant Shape Metal Legs Of Size 50 Mm X 20 Mm And Connectors Of Size 40 Mm X 40 Mm Horizontal Connectors,0.8 Mm Thick Wire Management Hole With Pvc Grooment On Table Top, * Single Metal Powder Coated Raceway & "T" Riser Leg Wire Carrying Below Top For Wire Management, All Metallic Parts Should Be Epoxy Polyester Powder Coating To Thickness Of 50 Micron (Approx) . * Three Layer Prelaminated Particles Board (Wood Product) Of Grade Ii Type Iii Of Is 12823/Latest . * The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark Compliant. The Bidder Should Either Offer Products Having Griha Compliance Or The Oem Should Have Fsc Certificate . The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org"

Supplying And Placing In Position of Library Chair * All Over Size Is : 470mm(L)X 400mm(D)X 890mm(H) , *The Chair Made Of Full Leatherette In Black Colour . It Will Comes In Matte Finsih In Contemporary Style . Details : * Arms : With Out Arms. * Use Of Ply: Seat & Back Plywood Made Of 12 Mm Hot Pressed. * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Support Seat Height Is @ 490mm . * Base : Four Chrome Legs . * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Providing & Placing of Executive Table Structure Of L Shaped Desk . Primary Work Surface Over All Size Is 2300mm(L)X 900mm(D)X 750mm(H) 50mm Thick Table Top Made Of Prelaminated Particle Board Work Surface With The Exposed Edges Shall Be Finished With 2mm Thick Edge Binding Tape Of Matching Colour And Shade With The Hot Melt Glue .Side Pannel Is Made Of 50mm Thick . * Provision Of Side Runner/A Of Size Is 1800mm(L)X 500mm(D)X 620mm(H) ,(Combination Construction Table Top Based On 4 Metal Ss Stud Grade 304,Side Runner/A Have 1 Open Shelve For Cpu,1 Open Door Fixed Shelve, 2 Openable Door + 3 Drawers & 2 Drawers Are Right Side Attached With Modesty And Side Pannel In Provided With Cetnral Lock For Security And Handles Are Provided For Easy Of Opening . Overall Construction Of Pedestal Is 18 Mm Thick Along With Fecia Of Drawers . * Three Layer Prelaminated Particles Board(Wood Product) Of Grade Ii Type Iii Of Is 12823/Latest , Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE * The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark Compliant. The Bidder Should Either Offer Products Having Griha Compliance Or The Oem Should Have Fsc Certificate . The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Providing & Placing of Pricipal Chair * High Back 360° Degre Revolving Chair Sku : Insight/Hb/Fl , * All Over Size Is : 620mm(L)X 700mm(D)X 1350mm(H) , *The Chair Made Of Full In Blue Colour . It Will Comes In Matte Finsih In Contemporary Style . Details : * Arms : Amrest Is Having Two Adjustment Heights (Up & Down) . * Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat And Back) . * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Support * Mechanism : Self Weighted Multi Locking Mechanism . * Only Seat Size Is 525mm(L)X 515mm(D) & The Back Size Is 465mm(L)X 770mm(H) Seat Maximum Height Is 545mm & Minimum Height Is 445mm & Back Height From Floor Maximum Height Is 1305mm & Minimum Height Is 1205mm * Gas Lift 100 Mm Telescopic Haudraulic * Base : Chome Base With Smooth Castors . * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Providing & Placing of Principal Chair Durian - - Office Seating - - Chaste Chair , Type : * Cantilever Chair Sku : 70011/Cn/A, * All Over Size Is : 590mm(L)X 490mm(D)X 980mm(H) , *The Chair Made Of Full Fabric In Black Colour . It Will Comes In Finsih In Contemporary Style . Details : * Arms : Fixed Arms P.P. Connected With Seat And Back . * Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat And Back) . * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Support * Base : M.S Powder Coated Tublar Frame Of Catilever Type . * The Product By Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

* Providing & Suppling Placing Position Of Modular Filing Cabinet Top Shall Be Made From 18 Mm Thick Prelaminated Particle Board Of Grade Ii Type Iii Of Is 12823/Latest. * While Rest Of The Sides As Well As Shelves And Shutter To Be Made Up Of 18 Mm Thick Prelaminated Particle Board. Machine Pressed Exposed Edges Shall Be Finished With 2mm Thick Edge Binding Tape Of Matching Colour And Shade Fixed Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. * Storage Unit With 4 Shutters Construction Is 2 Openable 4 Mm Thick Glass Door With 1fixed Shelve + 2 Openable Door With 2 Fixed Shelve , In Provided With 1 Universal Cam Lock For Security And Handles Are Provided For Easy Of Opening. Over All Height Of Product Is @ 1970 Mm . * Each Shutter Should Be Fixed With Required Numbers Hinges, Ss Tower Bolt Of 100 X 10, Double Strip Magnetic Catcher And Drawers Shall Have 100 Mm Size Ss Fancy Handles (One On Each Drawer) With Necessary Hardware/ Fitting/ Hinges Etc. Of Approved Quality(Make: Ebco).For Installation Of Side Unit Wooden Dowels And Minifix To Use For Additional Support. * Three Layer Prelaminated Particles Board ( Wood Product ) Of Grade Ii Type Iii Of Is 12823/Latest. * The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark Compliant. The Bidder Should Either Offer Products Having Griha Compliance Or The Oem Should Have Fsc Certificate . The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Sofa Set (3+1+1) 5 seater Sofa. Product Dimension : (L)2125mm X (D)960mm X (H)820mm, Sofa 1 Seater Size (L)1140mm X (D)960mm X (H)820mm sofa seat and back are made up of solid pine wood with hot pressed ply wood and upholstered with leatherette. Sofa molded with polyurethane foam & Silicon with minimum of 32 density and back plywood shall be designed with contoured lumbar support for extra comfort. The sofa shall have a wooden framed design running through the sides of the arm rests and wooden legs. MAKE DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE,( 5 YEARS WARRANTY) MODEL NO BERRY/55003

Supplying Placing and instillation of Solid Wood Center Table, Stylish rectangular wooden Center Table, Size:-(W)1130mm X (D)630mm X (H)410mm, Colour: - Brown - Walnut, Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE. The product must be from a Manufacturer having ISO 9001:2015,ISO 14001:2015,ISO 45001:2018,AIOTA,FSC,IGBC,INDIAN DESIGN,BIFMA COMPLIANT, GREEN GUARD PRO,SEDEX CERTIFICATE.

Reception Table,Table Dimension(L)2700mm X (D) 750mm X (H)750/1050mm,Supplying & placing in position of Reception counter as per photograph. Reception counter of size:- L-2700mm x D-750mm x H-1050mm is the décor which plays the key role in the kind of business sector to achieve the business. Reception desk as per photograph is made up of 25mm thick pre laminated particle board with PVC edges. The tabletop is supported with 18mm thick understructure of side panels and modesty panels. The front of the table is provisioned with a designed wooden panel & given an extra wooden top at 1050mm height made of 18mm thick pre-laminated with 2mm thick PVC edge banding. The table includes a mobile pedestal of size L-400mm x D-450mm x H-650mm made of 18mm thick prelaminated particle board with PVC edges. The pedestal is provisioned with 2 drawers and one filing drawer with locking facility. Provision of Keyboard tray with Pencil tray and hanging CPU holder. Provision of a side storage of size:- L-900mm x D-450mm x H-750mm Storage made of 18mm thk PRELAMINATED PARTICLE BOARD with PVC Edge Banding. Top made of 25mm thk board and all Sides, Shelves, Shutter etc made of 18mm thk Board with PVC Edge Banding. Back to the 9mm thk board. Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE

Supplying Placing and instillation of P.A & Admin Office Desk Desk Structure Of L Shaped Desk . Primary Work Surface Over All Size Is 1500mm(L)X 600mm(D)X 750mm(H) 25mm Thick Table Top Made Of Prelaminated Particle Board Work Surface With The Exposed Edges Shall Be Finished With 2mm Thick Edge Binding Tape Of Matching Colour And Shade With The Hot Melt Glue . Modesty Pannel 18made Of Mm Thick . *Provision Of Side Unit Of Size Is 900mm(L)X 450mm(D)X 750mm(H) ,(Combination Construction Wire Management Hole With Pvc Grooment On Table Top, Left Side Table Top Based On A 18mm Thick Side Pannel Engineered Wood & From Right Side Unit Have 2 Sliding Door + 1 Fixed Shelve . *Side Unit Size 900mm(L)X 450mm(D)X 750mm(H), In Provided With Lock For Security And Handles Are Provided For Easy Of Opening. Overall Construction Of Side Unit Is 18mm Thick Along With Fecia Of Slidding Shutters. *Three Layer Prelaminated Particles Board(Wood Product) Of Grade Ii Type Iii Of Is 12823/Latest , Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE * The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark Compliant. The Bidder Should Either Offer Products Having Griha Compliance Or The Oem Should Have Fsc Certificate . The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of P.A Chair for Lecture Table,* Medium Back 360° Degre Revolving Chair Sku : 70011/Mb/A , * All Over Size Is : 560mm(L)X 480mm(D)X 980mm(H) , *The Chair Made Of Full Fabric In Black Colour . It Will Comes In Matte Finsih In Contemporary Style . Details : * Arms : Fixed Arms P.P. Connected With Seat And Back . * Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat And Back) . * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Support * Mechanism : Centre Tilt Mechanism . * The Seat Size Is 475mm(L)X 490mm(D) & The Back Height Is @ 500 Seat Maximum Height Is 570mm & Minimum Height Is 470mm & Back Height From Floor Maximum Height Is 1080mm & Minimum Height Is 980mm * Gas Lift 100 Mm Telescopic Haudraulic * Base : 650mm Nylon Base With Smooth Castors . * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org",MAKE-DURIAN,MODEL NO MMPL/70011/MB,WARRANTY-5 YEARS.

Supplying and placing of Admin Table,Desk Structure Of Rectangular Shape . Primary Work Surface Over All Size Is 1500mm(L)X 750mm(D)X 750mm(H) 18mm Thick Table Top Made Of Prelaminated Particle Board Work Surface With The Hot Melt Glue Used For Fixing The 2mm Thick Pvc Edge Banding Made Of Same Matte Finish, Wire Management Hole With Pvc Grooment On Table Top. * Construction Right + Left Side Table Top Based On A 18mm Thk Engineered Wood And From Down Side 1 + 1 Fixed Pedestal Attached With Modesty Both Pedestal Have A Same Construction 3 + 3 Drawers- Per Drawer Have * 1 + 1 Fixed Pedeatal,In Provided With Cetnral Lock For Security And Handles Are Provided For Easy Of Opening. Overall Construction Of Pedestal Is 18 Mm Along With Fecia Of Drawers. * Three Layer Prelaminated Particles Board(Wood Product) Of Grade Ii Type Iii Of Is 12823/Latest. * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org".

Supplying and placing of Admin Chair for Lecture Table,* Medium Back 360° Degre Revolving Chair Sku : 70011/Mb/A , * All Over Size Is : 560mm(L)X 480mm(D)X 980mm(H) , *The Chair Made Of Full Fabric In Black Colour . It Will Comes In Matte Finsih In Contemporary Style . Details : * Arms : Fixed Arms P.P. Connected With Seat And Back . * Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat And Back) . * Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Support * Mechanism : Centre Tilt Mechanism . * The Seat Size Is 475mm(L)X 490mm(D) & The Back Height Is @ 500 Seat Maximum Height Is 570mm & Minimum Height Is 470mm & Back Height From Floor Maximum Height Is 1080mm & Minimum Height Is 980mm * Gas Lift 100 Mm Telescopic Haudraulic * Base : 650mm Nylon Base With Smooth Castors . * The Product By DURIAN ,MAPLE MOLDING PVT.LTD.,BOMBAY SAFE The Seller / Company Should Be Iso 9001:2008, Iso 9001:2015, Iso 50001:2018, Iso 14001:2015, Ohsas 18001:2007,Greenguard, Green Pro, Aiota, Indian Design Mark And Fsc Certified.The Bidder Should Be A Member Of Bifma And At Least Two Products Of The Oem Should Be Certified As Bifma Compliant And An Official Product Official Link/Screenshot Of The Product Listing Must Be Provided From Www.Bifma.Org",MAKE-DURIAN,MODEL NO MMPL/70011/MB,WARRANTY-5 YEARS.

08 PASSENGER / 544 KG LIFT

Supply, installation, testing & commissioning of 13 PASSENGER / 884 KG lift having contract speed of 1.5 MPS serving different floors in the lift shaft. Lift will be complete with combined luminous hall button with seven segment digital hall position indicator at all floor, car operating panel with luminous buttons, seven segment digital car position indicator combined with direction arrows, overload warning indicator, battery operated alarm bell and emergency light, fireman's switch at main lobby enclosed and as under:-

1) DESIGN OF LIFTS - PASSENGER TYPE

2) CAPACITY - 08 PASSENGER / 544. KG

3) SPEED - 1.5 m/s

4) DRIVE - V3F

5) WITH MACHINE ROOM

6)TRAVEL -13.950 Mtr. (Approximate)

7) FLOORS - GROUND TO SECOND FLOOR

8) NO. OF STOPS - 3 Stops

9) REQUIRED WELL SIZE - as per Drawing

10) POWER SUPPLY - 415 V - 3 Phase 50 HZ AC

11) AUXILIARY - Single Phase 220 V AC

12) CAR SIZE - Suitable for 10 Passengers

13) CAR ENCLOSURE

a) CAR CEILING - SS HAIRLINE FINISH

b) CAR PANELS - SS HAIRLINE FINISH

c) ILLUMINATION - LED LIGHT

d) CAR FLOORING - 20 MM RECESS (FLOORING BY CUSTOMER)

14) NO. OF ENTRANCE - ONE LOCATION FRONT

15) CAR ENTRANCE - AUTOMATIC COPD DOORS IN SS HAIRLINE FINISH

16) DOOR SAFETY - FULL HEIGHT INFRARED LIGHT CURTAIN

17) LANDING ENTRANCE - AUTOMATIC COPD DOORS IN SS HAIRLINE FINISH

19) ARD-TO BE PROVIDED

Add 18% GST

Add 1% Labour cess 1%

Dipanshu DIPANSHU PROMOTER AND BUILDER PVT. LTD.

Saurabh Jain