8440/E8 ADDN/ALTN OF RE-ELECTRIC WIRING (UNDERGROUND) IN LIEU OF OPEN OLD VANTAGE ELECTRIC WIRING IN OTM (BLDG. NO T-63, T-71, T-72, T-48, T-92, T-30) AND PROVISIONING OF 10 X WC TOILET NEAR HQ COY LIVING AREA UNDER GE (EAST) BAREILLY

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth and getting out soft/loose soil.

M&L for cement concrete 1: 4 : 8 type D 2 using 40mm graded stone aggregate in foundations, filling and mass concrete. complete all as specified and as directed by Engineer-In-Charge.

M & L for Reinforced cement concrete (Design Mix) with M-25 20 mm graded aggregates as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete. complete all as specified and as directed by Engineer-In-Charge.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batte on rough finished flat surface of concrete . complete all as specified and as directed by Engineer-In-Charge.

M & L for Reinforced cement concrete (Design Mix) with M-25 using 20 mm graded aggregates as in Columns, pillars, piers, posts and struts.complete all as specified and as directed by Engineer-In-Charge.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions on rough finished flat surface of concrete. complete all as specified and as directed by Engineer-In-Charge.

M & L for Reinforced cement concrete (Design Mix) with M-25 20 mm graded aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span. complete all as specified and as directed by Engineer-In-Charge.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, wall of mangers etc. complete all as specified and as directed by Engineer-In-Charge.

M & L for Reinforced cement concrete (Design Mix) with M-25 20 mm graded aggregates as in slab complete all as specified and as directed by Engineer-In-Charge.

S&F mild steel TMT bars of 8 mm dia and over cut to length bent to shape required including cranking and binding with mild steel annealed wire not less than 0.9 mm dia or securing with clips. complete all as specified and as directed by Engineer-In-Charge.

Ditto,but upto 8 mm dia as in stirrups , spacers and binders. complete all as specified and as directed by Engineer-In-Charge.

M&L Brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM1 : 6 all as specified and directed by Engr-in-Charge

M&L Brick work with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM1 : 6 all as specified and directed by Engr-in-Charge

M&L for 15 mm thick cement plaster in CM 1:6 on brick surface finished even and smooth without using extra cement Complete all as specified and directed by Engineer-in-charge.

M&L for 15 mm thick cement plaster in CM 1:4 on brick surface finished even and smooth without using extra cement Complete all as specified and directed by Engineer-in-charge.

M&L hardcore of gouge n exc n exc 63mm broken stone or boulder, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface.

M & L for cement concrete type D-2 (1:4:8) usng 40 mm graded broken stone aggregate 75 mm thick as sub base . complete all as specified and as directed by Engineer-In-Charge.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick of colour patteren as approved and as per manufacturers catalouge (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, in floor etc over 15mm thick screed bed with cement mortar 1:6 and set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and directed by Engr in charge

M & L for coloured glazed ceramic tiles 300 mm x450 mm & 7 mm thick on vertical surfaces of colour patteren as approved and as per manufacturers catalouge such as skirting, dados etc, set and jointed in neat cement slurry over and including 10 mm thick bedding layer/ backing coat in CM 1:4 complete and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-In-Charge.

S & F Pillar taps , cast copper alloy , with capstan heads, chromium plated, screwed down high pressure fancy type of 15 mm bore size with or without lettered Hot or Coldwith long screwed shanks and flynuts , screwed for iron pipe and fixed of Complete all as specified and as directed by Engineer-In-Charge.

S&F Cast copper alloy CP angle valve type stop cock with flange suitable for 15mm bore pipe screwed at both ends or high pressure with Capstan head confirming to Complete all as specified and as directed by Engineer-In-Charge.

S&F PVC connection 15mm size with PTMT nuts, of length 600mm Complete all as specified and as directed by Engineer-In-Charge.

S&F bib tap long body foam flow with flange of bore size 15mm, cast copper alloy, chromium plated, fancy type, with crutch or butter fly handle screwed down , screwed for iron pipe or for brass ferrule of Prayag /Saiko/ Parko Complete all as specified and as directed by Engineer-In-Charge.

S&F Brass chromium plated tubular towel rail 20mm dia 60cm long with and including flanges complete all as specified and as directed by Engineer-In-Charge

S & F soap dish stainless steel as approved by GE complete all as specified and as directed by Engineer-In-Charge.

S & F viterous china wash hand basin of size 550 x 400 mm, white colour flat back excluding taps, chain and plug and porcelean stopper but including brackets and CP waste fitting and 32 mm PVC waste pipe . complete all as specified and as directed by Engineer-In-Charge

S&F in repairs vitreous china squatting pan Orissa pattern size 580x440mm white with P or S trap front or back inlet and integral foot rests including connection to trap to flush pipe etc complete including for making good to floor etc Complete all as specified and as directed by Engineer-In-Charge.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including fixing plugs , bedding urinal against wall in cement mortar (1:2) etc. including CP Waste fitting and PVC waste pipe.Completed all as specified and directed by Engineer-in-charge.

S&F 10 litres capacity PVC Valveless symphonic action type flushing cistern high / low level white complete with inlet , ball valve float and handle including brackets and telescopic down pipes and jointing with WC complete complete all as specified and as directed by Engineer-In-Charge

M & L for 75 mm, dia PVC (SWR) floor trap, plain with SS grating including jointing with solvent cement. complete all as specified and as directed by Engineer-In-Charge (Trap shall be sealed properly with the existing pipe and got tested by Filling with water)

Supply and fixing Low density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 of 40 mm dia bore for wash hand basin Complete all as specified and directed by Engineer-in-charge.Make:Prayag

Supplying and laying of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. Note : The rate includes for chase cutting of Concealed for all the pipes shall be got tested before providing by Pressure testing machine and got approved and any leakage seepage observed , the conctractor shall be redo the same without any extra payment.

S& F PVC (SWR) pipes 110mm dia single, socketed in any length ,with rubber ring joints fixed to walls with MS clamps all as directed by Engr in charge.

S&F PVC (SWR) bends 110mm dia complete all as specified and directed.

S&F PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and directed.

S& F PVC (SWR) pipes 75mm dia single, socketed in any length ,with rubber ring joints fixed to walls with MS clamps all as directed by Engr in charge.

S&F PVC (SWR) bends 75mm dia complete all as specified and directed.

S&F aluminium powder coated frame for louvers section of size 75x40x1.6mm including 4mm thick glass in louvors of 100 mm width with glazing cleat and revolving arrangement of standard section of aluminium including rubber packing, aluminium beading or gasket for for aluminium sections for fixing glass sheet and necessary fittings complete screws plugs, handle, tower bolt, stay hooks including fixed Aluminium wire cloth etc all as specified and directed by Engineer in Charge.

M&L for two coat of OBD with preparing newly plastered walls surfaces with airless electric sprayers over a coat of primer applied using airless electric spryers over two coat of wall care putty of 1mm thickness prepared and sanded with electrically operated sanding machine. Application to be done through authorised applicator of manufacturer complete all as specified and directed.

Material and labour Material for applying Two coats of cement base paint on newly platered surface by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with max material hose length 30 mtr. The spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturerand accessories for applying cement base paint should be able to spray in hard to reach areas and penetration of cement base paint on the surface to achive excllent application using limited manpower complete all as specified and directed.

Returning, filling in, including spreading, leveling, and well ramming in layers n. exc. 25 cm thickness in soil. complete all as specified and as directed by Engineer-In-Charge.

Removing excavated material (Soils) to distance of exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point. complete all as specified and as directed by Engr-in charge

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position complete and all as specified and as directed by Engineer-in-Charge.

S&F in 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete

Supply and fixing in 15 mm bore float valve of high pressure PTMT with epoxy coated aluminuim rod and high density plastic ball screwed for iron pipe and fixed in tank which situated building including necessary complete all as specified and as directed.

M & L for cement concrete type C2 (1:3:6) (40 mm graded broken stone aggregate) 75 mm thick as in plinth protection and finish even and fair all as directed by Engr in Charge

S & F Solid PVC door frame of size 50 mm x 47 mm made out of 10 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification & drawing compete all as specified as directed by Engineer -in -charge

S & F Factory made solid panel PVC Moulded door shutter 28 to 30mm thick(stiles), with 2, 4, or 6 raised panel design 2mm thick Prelam PVC sheet on the front face and 2mm thick Plain colour PVC sheet on back face with particle Board core compete all as specified as directed by Engineer -in -charge

S & F 100 mm MS butt hinges medium weight cold rolled mild steel compete all as specified as directed by Engineer -in -charge

S & F 150 mm aluminium anodised barrel tower bolts of extruded section, ISI marked compete all as specified as directed by Engineer -in -charge

S & F 150 mm extruded aluminium alloy handles , fabricated type, anodised, ISI marked compete all as specified as directed by Engineer -in -charge

M & L 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches and jointes as specfified

Supply and spreading sand under interlocking tiles including watering and consolidation complete all as specified and directed.

M & L for Machine pressed precast conctete interlocking paver block with grey cement and pigment any shape ,size and colour confirming to IS 15658-2006of 60 mm thickness, M-40 Grade, all as specified and directed Engr-in-Charge.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) n.exc. 1.5sqm each Complete all as specified and as directed by Engineer-In-Charge..

Taking down shutters only n.exc. 2sqm each Complete all as specified and as directed by Engineer-In-Charge..

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50sqm and n exc 4sqm each Complete all as specified and as directed by Engineer-In-Charge..

S & F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification & drawing compete all as specified as directed by Engineer -in -charge

S & F Factory made solid panel PVC Moulded door shutter 28 to 30mm thick(stiles), with 2, 4, or 6 raised panel design 2mm thick Prelam PVC sheet on the front face and 2mm thick Plain colour PVC sheet on back face with particle Board core compete all as specified as directed by Engineer -in -charge

S & F in repair 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete all as spd as directed

S&F for 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S&F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed by Engineer-in-Charge. (Note :- S & F Glass/gauge shall be measured and paid for separately)

Dismantling of Boarding any description including shutters of existing cup boards.

S & F for 18 mm thick block board laminated on one side of commercial quality exterior Grade -I fixed with screws as in cup board shutters/shelves/rear side etc including lipping/beading all over shutter complete all specified and directed by Engr in charge

M & L for powder coated aluminium sliding window with anodized aluminium frame of 3 Track of size 92mmx32mmx 1.5mm thick, with sliding shutters(02 glass and 01 Wirecloth) with necessary channels (top rail, bottom rail and style of size 40mmx 18mm x1.10 mm thick) including glazing with tinted sheet glass panel 4.00mm thick and Aluminum alloy wirecloth 4mm nominal dia and avg width of aperture 1.4mm, fitted with necessary jointing cleats, glazing clips,locking device one for each shutter , rubber packing, aluminium beading, screws, rawl plugs including all necessary holes / drilling etc, complete all as specified as directed by Engineer -in -charge. Note : If mentioned section are not available in market, then immediate next higher section shall be provided by Contractor without any extra cost.

S & F 100 mm MS butt hinges medium weight cold rolled mild steel compete all as specified as directed by Engineer -in -charge

S & F 300 mm long and Mild steel Chromium plated sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed compete all as specified as directed by Engineer -in -charge

S & F mild steel spring 250mm for door, ordinary rat tail rod pattern springs, including roller and roller plate including welding as required for steel frame compete all as specified as directed by Engineer -in -charge ( work shall be carried out in MD Qtrs/ OTM accns in different locations of AOR GE east Bareilly as per site requirements upto 4 storieyed building)

S & F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tracks or wooden beeding patti.compete all as specified as directed by Engineer -in -charge

M & L two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces.compete all as specified as directed by Engineer -in -charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as directed.Complete all as specified and as directed by Engineer-In-Charge

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing the rubbish. Complete all as specified and as directed by Engineer-In-Charge

M & L for vetrified light shade ceramic tiles 7-8 mm thick square of size n exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and Including 15mm thick cement screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge.

Ditto all as per item No 74 but in Vertical surfaces size n exc 0.36 sqm such as dado/skirting including 10 mm thick rendering of cement mortar 1:4

M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. laid over 15 mm thick screed bed of cement mortar 1;6 set and jointed in neat cement slurry and pointed in white or coloured cement to match.Complete all as specified and as directed by Engineer-In-Charge..

M & L for coloured glazed ceramic tiles (300 mm x450 mm/300mmx600mm) & 7 mm thick on vertical surfaces such as skirting, dados etc, set and jointed in neat cement slurry over and including 10 mm thick bedding layer/ backing coat in CM 1:4 complete and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-In-Charge.

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer - in - Charge.

M&L 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement complete all as specified and directed

M&L for repairs to sunken floor slab with the following specifications:- (a) Demolition of PCC and taking out old brick bat fillihng and roughening surfaces of old concrete floor and wall by picking, sweeping clean and washing down with water to remove dust etc. (b) PCC 1:2:4,type B-0, using 12.5mm graded stone aggregate averaging 50mm thick as in sunken floor,with proper slope towards GI spout. The dia of GI Spuot pipe shall be 50mm Medium grade. The minimum length of Spout shall be 500mm and if any spout comes above chajja than the length of the spout shall be more than Chajja projection. Ends of Spout shall be tippered and any cutting through brick/ RCC structure shall be done by the Contractor rates are deemed to be included of this aspects. (c) providing 15mm thick cement plaster in cement mortar 1:3 mixed with water proofing compound @ 3% by weight of cement over bottom and vertical surfaces finishing the surface even and smooth with using extra cement. (d) Damp proof course on horizontal / Vertical surfaces with preparation & applying one coat of primer (33% dilution) and two coats of undiluted material @ 10.67 lts per 10 sqm of Make : smart care Damp proof of M/s asian paint or equivelent for water proofing compound. (e) Graded Brick bats filling under sunken floor of required thickness as per site, (f) PCC 1:3:6,type C-1,using 20mm graded stone aggregate 75mm thick, over brick bats filling as in subbase. Note:- (i) For payment purpose only plan floor area shall be measured. (ii) After Coating of Water proofing compound ponding test shall be carried out by filling the sunken surface with water for 72 Hrs and get approved by Engr-in-Charge if any leakage/ seepage noticed the Contractor will re do the whole process without any extra payment.

S&F in repairs gun metal, globe or gate valve, bore dia of pipe in 15 mm,

S&F in repairs metal, globe or gate valve, bore dia of pipe in 20 mm,

S& F in repair for 20 mm dia CPVC pipe as on wall , floor , ceiling , concealed etc complete and as directed by Engr in charge with all fittings and fixtured , jonting solution of ISI mark including making grove in wall/ceiling and finished with cement mortor 1:4 with plumbing nails for securing pipes etc directed.

S & F in Repair Pillar taps , cast copper alloy , with capstan heads, chromium plated, screwed down high pressure fancy type of 15 mm bore size with or without lettered Hot or Cold with long screwed shanks and flynuts , screwed for iron pipe and fixed Complete all as specified and as directed by Engineer-In-Charge.

S&F in Repair Cast copper alloy CP angle valve type stop cock suitable for 15mm bore pipe screwed at both ends or high pressure with Capstan head . Including dismanteling and making good the tiles if required of make ,Complete all as specified and as directed by Engineer-In-Charge.

S&F in Repair bib taps of bore size 15mm, cast copper alloy, , chromium plated, fancy type, with crutch or butter fly handle screwed down , screwed for iron pipe or for brass ferrule Including dismanteling and making good the tiles if requiredComplete all as specified and as directed by Engineer-In-Charge.

S & F in Repair brass cromium plated conceled stop cock of bore size 15 mm, in position conceled in walls/ceilings or floors complete duly making grooves filled with cement mortar in 1:4 finished to match with adjacent surfaces Including dismanteling and making good the tiles if requiredcomplete all as specified and as directed by Engineer-In-Charge

Supply and fixing in repairs 100 mm dia CP brass shower rose swivel type with extension CP rod 15mm dia and 300mm long with connecting rod suitable for 15mm bore pipe .Complete all as specified and directed by Engineer-in-charge.

S&F in Repair PVC connection 15mm size with PTMT nuts, of length 600mm Complete all as specified and as directed by Engineer-In-Charge.

S & F in Repair viterous china wash hand basin of size 550 x 400 mm, white colour flat back excluding taps, chain and plug and porcelean stopper but including brackets and CP waste fitting . complete all as specified and as directed by Engineer-In-Charge

S & F in repairs vitreous china wash down water closet pedestal pattern (EWC) white excluding flushing cistern & Incl white seat cover closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and flush pipe.Complete all as specified and directed by Engineer-in-charge.

S&F in repairs vitreous china squatting pan Orissa pattern size 580x440mm white with P or S trap front or back inlet and integral foot rests including connection to trap to flush pipe etc complete including for making good to floor etc Complete all as specified and as directed by Engineer-In-Charge.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed .

S & F in repairs CP health faucet special (1.5 mtr tube) with hook for EWC complete all as specified and directed by Engineer in charge

S&F in Repair Brass chromium plated tubular towel rail 20mm dia 60cm long with and including flanges complete all as specified and as directed by Engineer-In-Charge

S & F in repairs soap dish stainless steel as approved by GE complete all as specified and as directed by Engineer-In-Charge.

S & F for PVC (SWR) pipes, bore of pipe in 110mm, single socketed, in any length, with rubber ring joints, laid in floors or fixed to walls Complete all as specified and as directed by Engineer-In-Charge.

S&F PVC (SWR)pipe single socketed in any length with rubber ring joints,laid in floors 75mm dia Complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repairs Low density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 of 40 mm dia bore for wash hand basin Complete all as specified and directed by Engineer-in-charge.

S&F in repairs PVC(SWR) branch pieces, single (Single Y) equal or unequal or with parallel branches 75mm dia Complete all as specified and as directed by Engineer-In-Charge.

S & F in Repair for PVC (SWR) bends, any radius, bore of pipe in 75mm with cement solvent in position .Complete all as specified and as directed by Engineer-In-Charge.

S & F in Repair for PVC (SWR) bends, any radius, bore of pipe in 110mm with cement solvent in position Complete all as specified and as directed by Engineer-In-Charge.

Dismantling of PVC Pipes of any dia complete all as specified and directed.

S & F in repair PVC floor trap with CP grating weight of grating not less than 35 grams joints to waste pipe in run lead joint dia of outlet 75 mm of floor, trap with deep water seal and of heavy weight coated with tar/black bitumen paint including making good with existing surface by provision of tiles and refilling of the dismantel mnaterials complete all as specified and directed by Engineer-in-charge.

S & F in repairs curtain rod of CP MS 25 mm dianot less than 1.5mm thickness with chromium plated projected bracket both side as per sample fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw compete all as specified as directed by Engineer -in -charge

M&L for preparing newly plastered walls surfaces and applying two coats of oil bound distemper over 1mm thick wall care putty complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

Complete removal of existing treatment of wall and applying 2 coats of cement putty with primer in between 6 hrs interval, then applying 2 coats of Oli bound distemper any colour as approved by Engr-in-Charge.

M&L for preparing old plastered surfaces and applying one coats of white wash on ceiling complete all as specified and directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering

S & F 2 way Bib cock for health faucet with 2 way bib cock of . complete all as specified and directed by Engineer in charge

S & F vitreous china wash down water closet pedestal pattern (EWC) white excluding flushing cistern & Incl white seat cover of same make closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and flush pipe.Complete all as specified and directed by Engineer-in-charge.

S&L XLPE insulated armoured heavy duty electric cable with stranded aluminum conductor 1100 volt grade cross sectional area 25 Sqmm 4 core all as specified and directed

M&L for laying GI tubing light grade 40 mm dia with all fittings for cable protection all as specified.

M&L for excavation in trenches n.exc 1.5 m width and n.exc 1.5 m in depth in any type of soil/strata and getting out complete all as specified .

Returning, filling in and including spreading over , leveling , watering and well rammming in layers n.exceeding 25 cm thick all as specified.

Removal of surplus spoil from excavated site to a distance as directed by the Engr in Charge

M&L for dry sand cusioning for UG cable in trenches including spreading levelling and hand panning and consolidating complete all as specified.

S&L brick hard burnt sub class'B' old patern.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials to MES stores for segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all asspecified and as directed by the Engineer-in-Charge.

M&L concealed point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & including PVC Conduit (Concealed in wall/ceiling) of size 20mm dia and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings, junction boxes, inspection covers.modular cover plate etc, with and incl concealed MS sunken box of suitable size flush with wall surface, suitable for fixing of Modular type switches / sockets etc, complete all as specified and directed.

All as per item No 122 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 122 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 122 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

S&F Modular Switch 1 way 16 Amps, 1 Module size complete all as directed..

S&F Modular Socket 6 A, 2/3, Pin 2 Module size complete all as directed..

S&F Modular Socket 6A/16 A, 5 Pin ,2 Module size complete all as directed..

S&F Modular Switch 1 way 6 Amps, 1 Module size complete all as directed..

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S&F in replacement of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer, complete all as directed.

S&F in replacement LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection, complete all as specified and directed by Engineer in charge.

Supply and fixing in replacement sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete complete all as specified and as directed by the Engr-in-Charge..

Supply and fixing in replacement SPN 40 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning.

Supply and fixing in replacement SP 5 to 32 amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning.

S&F in replacement sheet metal enclosure DB's 415 Volts, IP-42, vertical including MCCB, TP, 100 Amp in 8 way VTPN DBs with 200 Amps rated copper bus bar complete all as directed by Engineer-in-charge.

M&L for sub main wiring with 2 run of 6 Sqmm FR, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn drawn through & PVC conduit of size 20 mm and above incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed complete incl taking out old wiring and conduit Note : 1. The cost of concealed conduit , taking down old wiring & accessories is deemed to be included in quoted rates. 2. The two run of 6 Sqmm wire and one run of 6 Sqmm wire will be measured as one unit.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 2020 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on completion .

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

M & L Taking down fan, sealing cable end, dismantling blades and removing fan and blades and deposit in E/M store for declaring BER

M&L concealed point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & including PVC Conduit (Concealed in wall/ceiling) of size 20mm dia and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fitting, junction boxes , covers etc, with and incl concealed MS sunken box of suitable size flush with wall surface, suitable for fixing of Modular type switches / sockets etc, complete all as specified and directed for the following :-

All as per item No 143 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

S&F Modular Switch 1 way 6 Amps, 1 Module size complete all as directed..

All as per serial item No 143 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

S&F Modular Switch 1 way 16 Amps, 1 Module size complete all as directed..

S&F Modular Socket 6A/16 A, 5 Pin ,2 Module size complete all as directed..

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete as specifed and directed.

S&F of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 Nos. MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer, complete all as directed.

S&F LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection, complete all as specified and directed by Engineer in charge.

Supply and fixing sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete complete all as specified and as directed by the Engr-in-Charge..

Supply and fixing SPN 40 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing SP 5 to 32 amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specfied and directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 2020 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on completion complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase, copper winding 230V of size 380mm sweep with, blades, and frame and louvers complete all as specifed and directed.

S&L XLPE insulated armoured heavy duty electric cable with stranded aluminum conductor 1100 volt grade cross sectional area 10 Sqmm 2 core all as specified and directed

M&L for laying GI tubing light grade 40 mm dia with all fittings for cable protection all as specified.

M&L for excavation in trenches n.exc 1.5 m width and n.exc 1.5 m in depth in any type of soil/strata and getting out complete all as specified .

Returning, filling in and including spreading over , leveling , watering and well rammming in layers n.exceeding 25 cm thick all as specified.

Removal of surplus spoil from excavated site to a distance as directed by the Engr in Charge.

M&L for dry sand cusioning for UG cable in trenches including spreading levelling and hand panning and consolidating complete all as specified.

S&L brick hard burnt sub class'B' old patern complete all as specifed and directed.

S&L XLPE insulated armoured heavy duty electric cable with stranded aluminum conductor 1100 volt grade cross sectional area 10 Sqmm 2 core all as specified and directed

M&L for laying GI tubing light grade 40 mm dia with all fittings for cable protection all as specified and directed.

M&L for excavation in trenches n.exc 1.5 m width and n.exc 1.5 m in depth in any type of soil/strata and getting out complete all as specified and directed.

Returning, filling in and including spreading over , leveling , watering and well rammming in layers n.exceeding 25 cm thick all as specified and diected.

Removal of surplus spoil from excavated site to a distance as directed by the Engr in Charge.

M&L for dry sand cusioning for UG cable in trenches including spreading levelling and hand panning and consolidating complete all as specified and directed.

S&L brick hard burnt sub class'B' old patern complete all as specified and directed.

M&L concealed point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & including PVC Conduit (Concealed in wall/ceiling) of size 20mm dia and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fitting, junction boxes, covers etc, with and incl concealed MS sunken box of suitable size flush with wall surface, suitable for fixing of Modular type switches / sockets etc, complete all as specified and directed for the following :-

All as per item No 172 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

S&F Modular Switch 1 way 6 Amps, 1 Module size complete all as directed..

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing angular lamp holder, metal cased body of brass with back plate in batten fittings, including Plastic square box of required size complete all as specified and directed by the Engineer-in-Charge

S&F LED Bulb 9 Watt complete all as specified and directed.

Supply and fixing in replacement LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and direcetd.

S&F of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 Nos. MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer, complete all as directed.

S&F LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection, complete all as specified and directed by Engineer in charge.

Supply and fixing sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 4 way with 200 Amps rated bus bar complete complete all as specified and as directed by the Engr-in-Charge..

Supply and fixing SPN 40 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing SP 5 to 32 amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 2020 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on completion complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase, copper winding 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed.

M/S SAJJAD HUSSAIN CONTRACTOR (BID ID -3402179)