Construction of Hostel at Bijay Kumar Academy, Govt. High School, Soharia, Bograi, Balasore, Odisha.

Item of Work Unit Quantity Rate Amount

1 Site Clearance

Cleaning & grubbing road land including uprooting rankvegetation, grass ,bushes,

shurbes, sapling and trees girth upto 300mm, removal of stumps of trees cut earier

and disposal of unsevicable materials and stacking of servicable materials to be used sqm 760.06 9.74 7399.18

or auctioned up to lead of 1000 meters including removal and disposal of top organic

soil not exceeding 150mm thickness.

2 Earthwork Excavation

Excavation in all kinds of soil, soft or hard including, but excluding soft and

a) hard rock, using equipments like pick-axe & shovel, Backhoe Loaders, excavators as Cum 226.41 319.66 72375.06

necessary & including shoring, strutting, bailing, pumping

Providing, driving with hydraulic piling rigs with power units and installing driven

cast-in-situ reinforced cement concrete piles of grade M-30 of specified diameter and

length below the pile cap, to carry safe working load not less than specified,

excluding the cost of steel reinforcement but including the cost of shoe and the length

of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment

shall be measured from top of shoe to the bottom of pile cap. As a specific

requirement, Portland puzzolana / Portland Slag cement conforming to IS 1489/ IS

3 455 shall be used for all concrete works. The concrete should be coherent, rich in

cement (not less than 400 kg/cum) & Pile shall be constructed by using temporary

casing upto minimum 1.5m to 3.0m inside the stiff to very stiff clay exists below very

soft / marine clay as per site conditions or design requirements. Adequate bentonite

mud shall be used as full depth temporary casing not been used during the boring

below temporary casing. All works in complete as per the drawings, specifications

and as directed by Engineer in Charge. (DSR 2023, Page No: 319, Item No-20.1)

Pile Foundation

4 Pile Load Tests

i) Initial test (Test Load 2.5 times the Safe capacity) Nos 1 72386.01 72386.01

ii) Routine test (Test Load 1.5 times the Safe capacity) Nos 1 25946.18 25946.18

3 Sand Filling

Filling in foundation, trenches and plinth with river sand, well watered and

compacted in layers of 1.8 mtr, with top surface dressed and leveled to proper

gradient including cost of all materials, conveyance, all taxes and royalties, loading Cum 464.65 1059.86 492460.71

and unloading, including cost of all labour, sundries, T & P etc. All complete as per

directions of the Engineer -in-charge.

4 Back Filling

Filling available excavated earth (excluding rock) in trenches plinth sides of

foundation etc. in layers not exceeding 20 cm in depth , consolidating each deposited

layers by ramming and watering, lead up to 50m and lift up to 1.5 mt etc. including cum 226.41 177.59 40208.37

cost of all labour, sundries T & P etc complete in all respect as per the direction of

Engineer-In-Charge.

Cement concrete of proportion (1:4:8) in foundation and floors using 4cm size clean

hard black crusher broken granite stone metal of approved quality and from approved

quarry including hoisting, lowering and laying concrete in layers not exceeding 15

cm. (6") thick to the required level ramming, watering, curing etc. complete including Cum 62.04 7751.70 480913.53

cost, conveyance, royalties of all materials with all labour and T&P required for the

work etc. complete in all respect and as per the direction of the Engineer-in-charge.

6 Anti-termite Treatment

Providing & applying of pre constructional anti-termite treatment Confirming to IS

6313 (Part-II) and creating chemical barrier under and around the column pits, wall

trenches, basement excavation top surface of plinth filling, junction of wall and floors

along with external perimeters of building, expansion joints, surrounding the pipes

and conducts etc. at the rate at 7 ,5 liter per sqm on vertical surface and 5.0 liter per

sqm on horizontal surface. Chemicals:- Imidachloprid 30.5 SC , Doses: - 2.1 ml per sqm 575.88 94.40 54363.07

lit of water cost of all materials, labour,conveyance, T&P , all taxes and hire charges

of machinaries as per direction of Engineer-incharge. (Make :- HI-Solution or Smart

Care Pest Control or Bharat Pest Eradicators)

7 Fly Ash brick(1:6)

Fly Ash brick masonry in cement mortar (1:6) in Substructure using Fly Ash bricks of

23 Cm. x 11 Cm. x 8 Cm. size having a crushing strength of not less than 75 kg./sqcm

with dimensional tolerance ± 2% including splays cutting circular moulding

chamfering and corbelling and similar such type of works with all necessary

projections watering and curing after immersing the bricks in water at least for six

hours before use including cost, conveyance, royalties and taxes of all materials with

all labour,labour cess and T & P required for the work complete in all respect as per

direction of Engineer-in-Charge.

Digitally signed by JAYA

Item of Work Unit Quantity Rate Amount

Foundation cum 87.92 6,881.81 605046.02

Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as

per approved designs and drawings having a minimum compressive strength (in work

test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted

in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken

granite stone chips and screened and washed sharp sand for mortar of approved

quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds

25 %) to be mixed in concrete mixture with Portland slag cement (PSC) including

hoisting, lowering, laying and compaction concrete by using vibrators, watering and

curing for 28 days, centering and shuttering then after dismantling and removing

debris from the work site and finishing the exposed

surface smooth providing grooves or beads wherever necessary including cost,

conveyance, loading, unloading, royalties and taxes of all materials and cost of all

labours, sundries, T & P required of the work etc.complete in all respect as directed

by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor

steel and binding wires and labour charges for straightening, cutting, bending etc. of

M.S. rods or tor steel tying the grills and placing in proper position.

Foundation and plinth

Column (Below Plinth) Cum 5.25 21149.29 111033.79

9 Reinforcement

Supplying Cutting, straightening coiled or bent up M.S. Rod or tor steel of primary

steel producers such as SAIL / Tiscon / RINL / JINDAL STEEL / SHYAM STEEL

(grade Fe-500D) etc. including bending, binding, welding and jointing if necessary

and tying the grills and placing in position as required for R.C.C. Work and for

providing fan hooks as required, hoisting, lowering, laying including cost,

conveyances, taxes of M.S. Rod or tor steel and binding wires of 18 to 20 gauge and

labour required for the work for bending, binding and tying the grills in all floors with

labour cess etc. (payment will be made on standard weight of B.I.S. for M.S. Rods or

tor steel only) etc. complete as per specification & direction of Engineer-in-charge.

Foundation and plinth qtl 156.00 10340.80 1613164.83

Ground Floor qtl 99.90 10340.80 1033010.20

Terrace Floor qtl 8.90 10462.71 93118.08

10 FLY ASH BRICK(1:6)

Digitally signed by JAYA

Item of Work Unit Quantity Rate Amount

Fly Ash brick masonry in cement mortar (1:6) in super structure using Fly Ash bricks

of 23Cm. x 11Cm. x 8Cm size having a crushing strength of not less than 75

kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding

chamfering and corbelling and similar such type of works with all necessary

projections watering and curing after immersing the bricks in water at least for six

hours before use including cost, conveyance, royalties and taxes of all materials with

all labour,labour cess and T & P required for the work complete in all respect as per

direction of Engineer-in-Charge.

Ground Floor cum 78.62 6927.05 544613.17

Second Floor cum 103.75 7867.72 816314.98

Terrace Floor cum 38.93 8446.36 328816.69

11 FLY ASH BRICK(1:4)

Providing Fly ash bricks masonry work using 23Cm. x 11Cm. x 8Cm having crushing

strength not less than 75Kg/Sqcm in cement mortar (1:4). Immersing the bricks in

water before use in all necessary projection splays cutting, circular moulding,

corbelling etc. Including cost of conveyance ,taxes & royalties, loading and

unloading of all materials & cost of all labour, scaffolding ,watering & curing

,sundries, T & P etc. complete as per the direction of Engineer-in-charge .

Ground Floor cum 3.68 7347.34 27039.39

First Floor cum 12.40 7784.86 96532.90

Second Floor cum 12.40 8288.01 102772.03

12 16 mm Plastering

Providing 16 mm thick cement plaster with cement mortar of mix (1:6) with screened

and washed sharp sand for mortar and finished smooth to the rough surface of walls

in all heights after racking out joints including watering and curing, rounding of

corners, providing grooves where ever necessary with cost, conveyance, royalties of

all materials with cost of all labour,labour cess, T&P, and scaffolding required for the

work etc. complete in all respect as directed by the Engineer in charge.

Ground Floor sqm 319.08 342.65 109331.22

First Floor sqm 300.65 356.14 107070.45

Second Floor sqm 300.65 370.28 111324.03

Terrace Floor sqm 297.57 385.14 114606.17

13 12 mm Plastering

Providing 12 mm thick cement plaster with cement mortar of mix (1:6) with screened

and washed sharp sand for mortar and finished smooth to the rough surface of walls

in all heights after racking out joints including watering and curing, rounding of

corners, providing grooves where ever necessary with cost, conveyance, royalties of

all materials with cost of all labour,labour cess, T&P, and scaffolding required for the

work etc. complete in all respect as directed by the Engineer in charge.

Ground Floor sqm 992.96 240.96 239258.46

Second Floor sqm 1054.50 251.94 265671.68

Terrace Floor sqm 91.25 257.68 23512.99

14 6 mm Plastering

Providing 6 mm thick cement plaster with cement mortar of mix (1:4) with screened

and washed sharp sand for mortar and finished smooth to R.C.C. work after closed

deep chipping & slurry treatment including watering and curing, rounding of corners,

providing grooves where ever necessary with cost, conveyance, royalties of all

materials with cost of all labour, T&P, and scaffolding required for the work etc.

complete in all respect as directed by the Engineer in charge.

Ground Floor sqm 598.53 266.33 159402.77

First Floor sqm 609.61 272.66 166217.85

Second Floor sqm 609.61 279.19 170195.80

Terrace Floor sqm 46.41 285.93 13269.82

15 Water Proofing

Waterproofing application:- Providing and application of two component polymer

modified flexible cementitious waterproofing coating at a thickness of 1.5 -2.5 mm

The membrane should have Elongation equal or more than: 30% , Crack Bridging

ability : Up to 1 mm, Adhesive strength: 1.0 N/mm² @ 28d, Tensile elongation: 60%

@ 20 °C, Shore A Hardness >85 (between 3 - 7 days) etc. as per direction of E.I.C

(For longer span, in terrace panel of 4m*4m should be done by groove cutting, and

filling with PU Sealant)(Make:MYK / Fosroc/Pidilite)

First Floor sqm 31.50 548.23 17269.18

Digitally signed by JAYA

Item of Work Unit Quantity Rate Amount

16 Grading Plaster

Providing 2.5cm thick Grading Concrete over roof slab with cement concrete (1:2:2)

using 6mm size black hard granite crusher broken chips and screened & washed sharp

sand for mortar and finished smooth to the rough surface of slab including watering

and curing with cost, conveyance, royalties of all materials with cost of all labour,

labour cess and T&P required for the work etc. complete in all respect as directed by

the Engineer in charge.

First Floor sqm 31.50 563.91 17763.17

17 Industrial vitrified tile

Supplying, fitting & fixing of Industrial vitrified tiles (40x40)cm in floors of

approved make laid on 20 mm thick cement mortar (1:4) (1 cement : 4 course sand)

and filling joints with slurry including cost of all materials, labour T&P etc required

for the work all complete as per direction of the Engineer-in-charge

18 Vitrified Floor Tiles

Providing full body matt finish vitrified tile flooring using vitrified tiles having

thickness of min 10mm conforming to IS 13755 of 1200x600 (shade to be decided as

per Ama Hospital scheme) (homogeneous) of premium quality (JOHNSON /

SOMANY/ KAJARIA/ RAK) in floors, treads on steps and landings on 20mm thick

bed of cement mortar of mix (1:4) laid in proper slope and gradient with screened and

washed sharp sand for mortar and fixing with neat white cement slurry,grouting the

joints with neat white cement slurry mixed with required quantities of pigments of

approved make to match the shades of the vitrified tile if required , watering and

curing for 21 days, including cost, conveyance, loading, unloading, royalties and

taxes of all materials, cost of all labour,Labour cess , sundries, T&P required for the

work, complete in all respect as per specification and direction of Engineer-in-charge.

Ground Floor sqm 426.36 1179.03 502695.79

Second Floor sqm 354.67 1210.21 429223.26

19 Vitrified Floor Skirting

Providing, fitting, fixing vitrified tiles of premium grade having thickness 8mm to

10mm confirming to IS 13756 of size 600mm x 600mm Plain (Ivory) of approved

make (JOHNSON/ SOMANY/ KAJARIA/ RAK) as directed by Engineer-in-charge

in dados skirting and risers of steps on 12mm thick cement plaster (1:3) jointed with

neat cement slurry mixed with pigment to match the shades of the tiles including

rubbing and polishing etc. complete with cost, conveyance, royalties of all materials

all labour, labour cess complete in all respects.

Ground Floor sqm 48.68 1345.87 65518.42

First Floor sqm 52.36 1369.34 71693.31

Second Floor sqm 52.36 1392.81 72922.12

20 Kotta Flooring

Kotta Tile (SOR PG-11, Sl-93)

Ground Floor sqm 38.41 590.24 22670.96

First Floor sqm 32.52 590.24 19191.52

Second Floor sqm 32.52 590.24 19191.52

21 Kotta Skirting

Kotta Tile (SOR PG-11, Sl-93)

Ground Floor sqm 3.21 590.24 1894.66

First Floor sqm 3.21 590.24 1894.66

Second Floor sqm 3.21 590.24 1894.66

22 Ceramic Toilet tiles

Supplying fitting, fixing ,ceramic glazed tiles 30cm x30 cm / 40cm

x40 cm in floors of size of approved make with 20mm thick bed of

cement mortar (1:4) jointed with neat cement slury mixed with

pigment to match the shades of the tiles complete including cost of

all materials,Labour T&P etc required for the work .

Ground Floor sqm 21.32 2608.58 55614.90

First Floor sqm 39.42 2624.17 103444.65

Second Floor sqm 39.42 2639.75 104059.12

23 Ceramic Skirting

Digitally signed by JAYA

Item of Work Unit Quantity Rate Amount

Supplying & Fixing ceramic tiles in Dados, Skirting and risers of

steps on 12 mm thick cement plaster (1:3) Jointed with neat

cement slury mixed with pigments to match the shade of the tiles

including rubbing and polishing including cost of all meterials etc.

Ground Floor sqm 97.21 2373.24 230700.25

First Floor sqm 89.78 2388.83 214456.98

Second Floor sqm 89.78 2405.22 215928.41

Providing and fixing System Aluminum works for Sliding doors and

windows of TOSTEM make with 35mm visible aluminum section

width in the center mullion. The extruded aluminum sections should

be made from Grade 6063 & Anodized with Texguard coating ,

silicon coated to suit marine atmosphere. All profiles should be

None insulated Profiles. Corner connection will be Butt joint with

Screw using Nano gaskets for sealing. All other major Accessories

should also be made by the same manufacture. All Slider doors &

windows will be center locking. Integrated Anti-lift in slider panel,

EPDM gaskets should be used in slider windows & doors in all

meeting points instead of Brush Pile. The outer frame Depth will be

72mm. All materials which are used should be corrosion-resistant

24 so that they are good functioning in different environments and

that there are no negative influences either on the aluminum or on

the surface treatment. The system should allow the application of

glazing or panels with thickness up to 8mm. The external perimeter

of aluminium sections should be Anodized with Texguard coating,

the system should qualify Airtightness 8 m3/h.m2 at 75Pa of

pressure, Water tightness 150 Pa, Wind load resistance 1200 Pa.

System should have a 10-year warranty on properties, functionality

and design, within restrictions defined by technical specifications of

anodizing & 1-year warranty on wearing parts only applies to

normal and realistically foreseeable use. All Slider doors & windows

will be center locking .

Sliding upvc door sqm 2.52 7998.98 20157.44

25 Aluminium DOOR

Providing and fixing Aluminium Openable Door duly made of

Aluminium FRAME section 65mm x 32mm and SHUTRER section

47mm x 44mm. The minimum wall thickness of the external

surfaces of Aluminium profile shall be 2.1mm ±0.3mm Frame and

sutters must be structurally 1.2mm thickness . The Door shall be

fitted Groller, Hinges, Handle, conextruded with Aluminium profile

for shutter and beading ensures quality consistancy, site using

anchor fasteners, silicon sealant incluing all cost, conveyance of all

materials,cost of all labour,T&P, sundries etc. complete in all

respect including GST as directed by the Engineering-in-Charge

Ground Floor sqm 33.81 6097.06 206141.60

First Floor sqm 31.50 6097.06 192057.39

Second Floor sqm 31.50 6097.06 192057.39

26 WPC Door Frame

Providing & Fixinng factory made 100% Solid WPC ( Wood Polymer

Composite )- Door Frame 125 mm x 65 mm Single Rebated, made

from Wood Polymer Composite (Single Extruded Process ) material

comparising of virgin PVC polymer of K Value 57-60 ( Suspension

Grade ), Calcium Carbonate and Natural Fibers ( Wood Powder/

Rice Husk/ Wheat Husk ) and Non toxic additives fabricated with

meter Joints after applying PVC solvent Cement & screwed with full

body treaded star headed screws having minimum frame density of

780 kg/ cbm & an ISO 9001 - 2015 Certified Company, having

good screw holding capacity ( Screw

Withdrawal strength of ( Min. 990 N ),Minimum Compressive

Strength of 58 N/mm2, Modulus of elasticity 900N/mm2 and

resistance to spread of flame of class A category with property of

being termite / borer proof , water / Moisture Proof & Fire retardant

& Fixed in position with SS Dash Fasteners / Hold Fast of reuired

dia and lenght, , all as per specifications drawings as directed by

the Engineer-In-Charge. Material test certificate and authentication

should be compulsory provided by the manufacturing company.

(Make- Rajashree, Amulya,Terra plast)

Ground Floor rmt 24.75 1380.62 34170.29

First Floor rmt 79.20 1380.62 109344.92

Digitally signed by JAYA

Item of Work Unit Quantity Rate Amount

Second Floor rmt 79.20 1380.62 109344.92

27 WPC Door Shutter

Supplying and fixing of Powder coated 50-60 microns approved

colour of Aluminium 40mm Casement series Door Unit with suitable

aluminium extrude profiles. the system is designed to

accommodate 12mm clear Factory made single leaf Solid WPC

(Wood polymer) composite door shutter of 25mm thickcompacted

with wood grain finish structural foam panel of 29mm thickness

and a density of 20kg/cu.mtr shall be used as core material for

fitting the metal fittings such as tower bolts, aldrops, handles etc

shall be provided. A structural adhesive compatible with (EPS) foam

shall be used for bending the core material, The material and

process for manufacturing the door shutters shall conform to RV-

TIFAC composites Design Centre's standards and specifications and

the door shutters Conforming to relevant I.S.specification. The

finish of door shutter will be plain colour white/ Ivory/ Beige/ Light

grey/ Mahogany/ Teak wood or any other colour using high quality

pigments. Three heavy whight mild steel butt hinges type-I(ISI

marked) size 100mm are to be fitted on one side of shutter.

Ground Floor sqm 7.88 4250.51 33472.79

First Floor sqm 25.20 4250.51 107112.94

Second Floor sqm 25.20 4250.51 107112.94

28 RCC VENTILATORS

Supplying and fixing-Fixing of R.C.C. jally for toilet ventilation

Ground Floor sqm 1.80 826.00 1486.80

First Floor sqm 3.00 826.00 2478.00

Second Floor sqm 3.00 826.00 2478.00

29 Aluminium WINDOWS

Providing and fixing of 2 track 2 panel sliding windows Aluminium

Sliding Windows duly made of Aluminium FRAME section 65mm x

32mm and SHUTRER section 42mm x 22mm. The minimum wall

thickness of the external surfaces of upvc profile shall be 2.1mm

±0.3mm Frame and sutters must be structurally 1.2mm thickness .

The windows shall be fitted GLASS And gasket EPDM,Roller,Star

lock,etc conextruded with Aluminium profile for shutter and beading

ensures quality consistancy, site using anchor fasteners, silicon

sealant incluing all cost, conveyance of all materials,cost of all

labour,T&P, sundries etc. complete in all respect including GST as

directed by the Engineering-in-Charge.

Ground Floor sqm 36.45 3732.86 136062.72

First Floor sqm 30.38 3732.86 113385.60

Second Floor sqm 30.38 3732.86 113385.60

Terrace Floor sqm 4.05 3732.86 15118.08

Supplying, fitting & fixing in all floors of M.S. grills, grill gates, M.S.

gates, garage door, collapsible gates with top and bottom rails,

steel windows, critical frames for windows, stair case and parapet

railing made out of M.S Square bar/ flat including stair case hand

railing with 40mm. dia G.I.pipe etc. including painting two coats

over a coat of redoxide primer as per approved drawing and design

with cost of all materials & labour, labour cess, T&P, sundries etc.

complete in all respect as per specification & direction of the

Engineer-in-Charge.

Terrace Floor kg 227.70 145.31 33085.99

31 Synthetic Enamel Paint (Iron Work)

Painting two coat with approved synthetic enamel paint to new iron

work over a coat of Red oxide primer including cost, conveyances,

royalties, taxes of all materials and cost of all labour with T&P

required for the work etc. complete as per specification & direction

of Engineer in charge.

(Make-Asian/ Berger/ Dulux/ ICI or equivalent make duly approved

by Engineer-in-charge).

Ground Floor sqm 36.45 219.24 7991.44

First Floor sqm 30.38 224.79 6828.00

Second Floor sqm 30.38 230.45 7000.04

Digitally signed by JAYA

Item of Work Unit Quantity Rate Amount

32 Antifungal Weather Coat Paint

Wall painting two coats with Antifungal weather coat paint (1st

quality) exterior grade of approved make & approved shade over a

coat of primer to make an even finished surface in all floors and

heights with all scaffolding and staging charges including cost,

conveyance, cost of all labours, T & P, sundries etc. as required for

the work complete in all respect as per the direction of the

Engineer-in-Charge.

(Make: Asian/ Berger/ Dulux/ ICI or equivalent make duly

approved by Engineer-in-Charge)

Ground Floor sqm 992.96 117.53 116700.02

Second Floor sqm 1054.50 120.95 127541.32

Terrace Floor sqm 91.25 122.84 11208.97

33 Plastic Emulsion Paint

Painting two coats with plastic emulsion paint with a approved

quality primer to make an even finished surface in all floors and

heights to wall surface of approved make and shade including sand

papering, applying putty wherever necessary & cost of scaffolding,

staging charges with cost, conveyance, cost of all labour,labour

cess, T&P etc. complete as per the direction of the Engineer-in-

(Make: Asian/ Berger/ Dulux/ ICI or equivalent make duly

approved by Engineer-in-charge)

Ground Floor sqm 917.61 126.91 116452.97

First Floor sqm 910.26 129.43 117818.77

Second Floor sqm 910.26 132.03 120181.81

Terrace Floor sqm 343.98 134.72 46341.19

34 Cement Primer

Priming one coat with wall cement primer (water bound) to make

an even finished surface in all floors and heights to wall surface of

approved make and shade including sand papering, applying putty

wherever necessary & cost of scaffolding, staging charges with

cost, conveyance, cost of all labour,labour cess T&P etc. complete

as per the direction of the Engineer-in-charge.

(Make: Asian/ Berger/ Dulex/ ICI or equivalent make duly

approved by Engineer-in-Charge)

Ground Floor sqm 1910.56 95.93 183287.38

First Floor sqm 1974.72 98.29 194102.64

Second Floor sqm 1964.75 100.65 197760.07

Terrace Floor sqm 435.23 103.13 44886.14

Finishing plastered surfaces of walls with cement based wall putty

(Water based) of approved make (JK White/ Birla white or

equivalent make duly approved by Engineer-in-Charge) and

finishing the surface smooth and even by sand papering to receive

painting in walls, at all heights with staging wherever necessary

with cost, conveyance, cost of all labour,labourcess, all T&P etc.

required for the work complete in all respect as per the direction of

the Engineer-in-charge.

Ground Floor sqm 1910.56 99.00 189148.96

First Floor sqm 1974.72 99.00 195500.73

Second Floor sqm 1964.75 99.00 194514.30

Terrace Floor sqm 435.23 99.00 43088.64

Digitally signed by JAYA

Sl No Item Description Unit Qty Rate Amount

1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in surface

/ recessed medium class PVC conduit, with modular switch, modular

plate, suitable GI box, ceiling Rose and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as

2 Wiring for group controlled looped light point/ fan point/ exhaust fan

point/ call bell point ( without independent switch control ) with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in surface

/ recessed medium class PVC conduit, ceiling rose and earthing the point

with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable

etc. as required.

3 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed medium class

PVC conduit, 2 way modular switch, modular plate, suitable GI box and

earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable etc. as required. Nos 6.00 1753.48 10520.88

4 Supplying and fixing two module stepped type electronic fan regulator on

the existing modular plate switch box including connections but excluding

modular plate etc. as required. Nos 75.00 553.42 41506.50

5 Supplying and fixing modular blanking plate on the existing modular

plate & switch box excluding modular plate as required. Nos 10.00 29.50 295.00

6 Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 3 pin 5/6

amps modular socket outlet and 5/6 amps modular switch, connection

etc. as required. Nos 41.00 645.46 26463.86

7 Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providng and fixing 2 Nos. 3 pin

5/6 A modular socket outlet and 2 Nos. 5/ 6 A modular switch,

connections etc. as required. Nos 107.00 914.50 97851.50

8 Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 6 pin 15/16

amps modular socket outlet and 15/16 amps modular switch, connection

etc. as required. Nos 34.00 807.12 27442.08

9 Supply, delivery, installation & testing of TV outlet boards containing a

clip-in type modular TV Socket outlet fixed on metallic concealed box

including connections and making good the damages caused complete as

required and as per direction of Engineer-in-charge. Nos 2.00 676.14 1352.28

SUB MAIN WIRING

10 Wiring for circuit/ submain wiring alongwith earth wire with the following

sizes of FRLS PVC insulated copper conductor, single core cable in

surface/ recessed medium class PVC conduit as required.

b. 2 X 4 sq. mm + 1 X 1.5 sq. mm earth wire Mtr 300.00 221.84 66552.00

c. 4 x 6sqmm + 2 x 2.5sqmm earth wire Mtr 150.00 374.06 56109.00

d. 4 x 10sqmm + 2 x 4sqmm earth wire Mtr 150.00 523.92 78588.00

11 Supply and drawing co-Axial TV cable Rg-6, grade 0.7mm solid copper

conductor PE insulated shielded with fine tinned copper braid and

protected with PVC sheath in existing surface/recessed steel/PVC conduit

as required. Mtr 60.00 113.28 6796.80

LIGHTING FIXTURES

Note: Dummy box for surface mounted fixtures only, fans and exhaust

fans with all accessories, as required.(The colour temprature for fixtures

shall be above 4000 deg K, CRI Min 80 & white in colour as per

12 Supplying & fixing of 9W Downlight, recessed in ceiling, with fixed light

distribution suitable for 9W 6000K LED based lamp with electronic driver

etc,complete with all fixing accessories as required. Nos 7.00 1362.90 9540.30

13 Supplying & fixing of 12W Downlight, recessed in ceiling, with fixed light

distribution suitable for 12W 6000K LED based lamp with electronic driver

etc,complete with all fixing accessories as required. Nos 38.00 1805.40 68605.20

14 Supplying & fixing of 18W Downlight, Surfaced fitting, with fixed light

distribution suitable for 18W 6000K LED based lamp with electronic driver

etc,complete with all fixing accessories as required. Nos 12.00 3363.00 40356.00

15 Suppling and fixing single wall mounted 20watt LED type batten fitting

compelet with electronic driver and LED Tube etc directly wall/ ceiling

including conecttion with 1.5 SQMM FRLS PVC insulated copper conductor

and earthing the body etc as required. Nos 203.00 1545.80 313797.40

16 Suppling and fixing wall mounted 10watt LED type Mirror fitting compelet

with electronic driver and LED Tube etc directly wall/ ceiling including

conecttion with 1.5 SQMM FRLS PVC insulated copper conductor and

earthing the body etc as required. Nos 6.00 713.90 4283.40

Digitally signed by JAYA

Sl No Item Description Unit Qty Rate Amount

17 Supplying and fixing Surface mounted 10 watt LED type Bulk-head fitting

comprising of pressure die cast housing with acrylic diffuser (IP65) and

complete with integrated electronic driver etc directly on wall/ceiling

including connection with 1.5 sq.mm FR PVC insulated copper conductor

cable and earthing the body etc. as required. Nos 13.00 2183.00 28379.00

18 Supplying and fixing call bell/ buzzer suitable for single phase,230 V,

complete as required. Nos 2.00 251.34 502.68

19 Supply, delivery and fixing of Ceiling fan hook box made out of 18 swg

GI sheet and containing 10 mm dia round ms bar projecting atleast

150mm on either side & duly bent to accommodate ceiling fan down rod

bolt & having earthing arrangement as per direction of Engineer-in-

20 Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15

mm dia, heavy gauge including painting etc. as required as per direction

of Engg.-in-Charge. Nos 75.00 46.02 3451.50

21 Supply and installation of star rated ceiling fan of following sweep

including wiring the down rods of standard length (up to 30cm) with

1.5sq mm FRLS PVC insulated copper conductor etc. as required.

22 Supply and installation of ISI marked wall mounted fan of following

sweep including Connection from provided socket outlet.

23 Supply and installation of 250mm. 230V A.C exhaust fan, with louver in

the existing opening including making good the damage connection

testing commissioning etc as required. Nos 16.00 2183.00 34928.00

DISTRIBUTION BOARD

24 Supplying and fixing of following ways surface/ recess mounting, vertical

type, 415 V, TPN MCB distribution board of sheet steel, dust protected,

duly powder painted, inclusive of 200 A tinned copper bus bar, common

neutral link, earth bar, din bar for mounting MCBs (but without MCBs and

incomer ) as required . (Note : Vertical type MCB TPDB is normally used

where 3 phase outlets are required.)

25 Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required. Nos 5.00 29.50 147.50

26 Supplying and fixing following rating, Four pole, (single phase and

neutral), 415 volts, residual current circuit breaker (RCCB), having a

sensitivity current upto 100 milliamperes in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

b) 6-32A Single Pole MCB Nos 72.00 165.20 11894.40

27 HOSTEL LT PANEL

Design, Fabrication, Supply, Erection,Testing and commisioning of

Powder coated Main LT Panel fabricated out of 14 guage CRCA sheet

steel in cubical, compartmentallised, free standing floor /wall mounted,

dust and vermin proof, with reinforcement of suitable size angle iron,

channel, T -iron or flats as required. Cable gland plates shall be provided

on top as well as bottom of the panels. Panels shall be treated with all

anticorrosive process before painting as per specification. Panels shall be

suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth

bus and lifting hooks as required in case of large panels.Approval shall be

taken for each panel before fabrication. (All hardwares like nuts and bolts

used shall be Galvanized and Zinc passivated) as per Specification.

Type of construction: Form 3B

IP classification: 42

Colour: Gray Powder Coated, as per approved sample

Incomer 1:- (EB Supply)

1 nos, 160 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit

Breaker of fault breaking capacity 25 KA (ICS=ICU up to 433 V)

complete in all respect.

(ii) 01 set of 0-160Amps Ammeter with CTS. (DIGITAL)

(iii) 01 set of 0-500 voltmeter .

One set - Indicating lamp for ON/OFF/Trip and Phase indication with

control fuse/ MCB.

TPN aluminum bus bars of minimum of 200 Amps capacity with heat

shrinkable colored sleeves and I/C DMC/SMC bus bars supports at

required intervals complete for cross section, size supports & their

spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

EIGHT (10) - Outgoing Feeders (For 3 LDB, 3 PDB, 1 UPS and 3 Spare)

One(1)- 63 Amps, TPN, MCB

Digitally signed by JAYA

Four (4) - Outgoing Feeders (For 4 Spare) comprising of

Sl No Item Description Unit Qty Rate Amount

One (1) 40 Amps, DP, MCB

One (1) - 40KA Type II 3+1 spd with 1no 4P MCB

Panel complete as above Set 1.00 144927.60 144927.60

28 Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium

conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1

/ IS:1554 part-1 respectively & ISI marked.

a) 3.5C x 70 Sqmm XLPE cable Mtr 50.00 522.74 26137.00

29 Laying of One No. PVC insulated and PVC sheathed/XLPE power cable of

1.1 KV grade of following size in the existing RCC/HUME/MASONERY

TRENCH/HDPE Pipe/DWC Pipe/ Metal Pipe/On Wall Surface(Clamped with

saddle/PVC & UPVC Pipe)/ Cable Tray etc. as required.

TERMINATION OF CABLES

30 Supply & Making end Termination with brass compression gland and

Cu/aluminium lugs for PVC insulated and PVC sheathed cable of 1.1 kv

grade (without cost of Cable)

31 S/IT/C of materials and installation of GI earth plate 600mm x 600mm x

6mm thick ISI marked with G. I. nut bolts & washers including cost of

burnt wood charcoal, salt, foreign soil, water pouring arrangements, brick

masonary enclosure on top with removable RCC cover complete with

labour for excavation of pit in all kinds of soil & rock as required and as

per direction of Engineer-in-charge.The entire earthing system should be

Replacement Warranty will be 2 years

32 Providing and fixing 25 mm X 5 mm dia GI strip on wall/surface or in

recess for connection etc. as required. Mtr 30.00 177.00 5310.00

LIGHTING ARRESTER

33 Supply of 8 mm Aluminum Round Conductor.Tested as per IEC 62561. as

per direction of engineer in charge. Mtr 250.00 175.82 43955.00

34 Supply of Roof conductor holder for parapet- Polyamide Conductor

holder:With M8 female thread or diameter 7mm, M8 Screw to connect

the conductor holder.Weather and temperature resistant from -35 to +90

degree Celsius tested. Conductor holder @ 1 meter distance.Tested as

per IEC 62561. as per direction of engineer in charge.

35 Supply of Polyamide roof cable holder for flat roof: DIN 48829 Form B1.

Closed form with bottom. Filling weight 1Kg (frost-resistant concrete).

Sleeve from polyethylene, black @ 1 meter distance. Tested as per IEC

36 Supply of Connector: For T cross and parallel connectors. Quick

installation using hexagonal bolt M10X30 high-grade hot dip galvanised.

Tested as per IEC 62561.(2nos/expansion piece ). No 12.00 239.54 2874.48

37 Supply of 1 mtr vertical air terminal with mounting accessories on the flat

surface to meet the requirements of IS/IEC 62305. Tested for Electrical ,

mechanical and chemical as per IEC 62561. Tested for 100kA lightning

38 Supply for Providing of Stand for Fang Fix system 16 kg made up of frost

resistant concrete. No 8.00 1125.72 9005.76

39 Supply of Test Joint (Folding Clamp) suitable to connect 8mm round

conductor and max by 30x3 mm GI strip as specified in drawing and

directed by Engineer. Tested for 100kA lightning current.

40 Supply of IP 66 Poly Propylene Junction Box. Installation at 1Mtr Height

For Test Joint .Internal dimensions: 100x100x48 mm. No 6.00 326.86 1961.16

41 Supply of Galvanised Steel Flat 30X3 mm thickness from earth electrode

directly in ground as required. Flat conductor Hot Dipped Galvanized.

Tested as per IEC 62561. Mtr 45.00 318.60 14337.00

42 Supply for Providing of Cross connector for Flat: Suitable for 30mm

Galvanised steel strip. Installed with 4 nos of hexagonal plate. Tested for

100kA lightning current. No 6.00 297.36 1784.16

43 Supply of flat conductor holder- Fit: FL 30, With mounting hole 6.2 x 22

mm, With 2 cylinder bolts M6 x 16 and over-piece from hot-dip

galvanised steel, Bottom section from polyamide, black. Tested as per

44 Supply for Providing of Plastic Corrosion Protection strip: Approx 1.1 mm

thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric.

45 Supply of UL Listed maintenance free ,Low carbon copper coated earth

rod of 3 metre electrode having diameter of 17.2 mm with copper coating

thickness of 250micron tested as per IEC 62561-2. No 6.00 4935.94 29615.64

46 Supply of universal clamp made of SS to connect rod with flat conductor.

47 Supply of Earth conductivity enhancing mineral compound shall be of 25

No 6.00 Digitally

3348.84 signed by20093.04

kg/pit tested as per IEC 62561-7,TCLP tested. PRAKASH GURU

Sl No Item Description Unit Qty Rate Amount

48 Supply of The above arrangements shall be provided with Heavy duty

earth champer of 5000kg load bearing capacity to ensure the safety of

earthing system. No 6.00 2559.42 15356.52

49 Installation of The above arrangements including all accessories as per

Direction of Engg. In charge. Job 1.00 41300.00 41300.00

1 Terrace Pump

Supplying, installation, testing and commissioning of electric driven

terrace pump suitable for automatic operation and consisting of following,

complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron

body & bronze impeller with stainless steel shaft, mechanical confirming

Suitable HP squirell cage induction motor TEFC type suitable for operation

on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for

enclosure, horiziontal foot mounted type with Class-'F' insulation,

conforming to IS-325.

M.S.fabricated common base plate, coupling, coupling guard, foundation

bolts etc.as required.

Suitable cement concrete foundation duly plastered and with anti

vibration pads.

450 lpm at 35 m Head

Pump as Above Set 1.00 94400.00 94400.00

Supply, installation, testing and commissioning of Wall mounted

sectionalised, front operated top entry dust and vermin proof M.V.Panel

Boards suitable for operation at 415V, 3 phase, 4 wire, 50Hz distribution

system fabricated out of 2.0 mm thick CRCA sheet, compartmentalised

with hinged lockable doors, dust and vermin proof, powder coated of

approved shade after 7 tank treatment process, cable alley, insulated

busbar with heat shrienkable PVC sleeve, base channel, complete with all

accessories including interconnections, proper earthing etc as required.

Make:-LEGRAND, L&T, Siemens or equivalent.

One (1)- 63 Amp, 10 KA,4P MCB with 3 Nos Phase indicating lamps with

control fuse/ MCB, Digital Voltmeter & Ammeter with selector switch

suitable for motor duty.

One (1) - DOL with O/L and Single Phasing Preventor suitable for 10 HP

motor(minimum). ON/OFF indication lamps, Auto manual switch and

ON/OFF push button.

One (1) - Set of Auxilliary relay for automatic operation through pressure

Panel As Above Set 1.00 32767.42 32767.42

3 Supply, laying, connecting, testing & commissioning of following size of

1.1 kv grade multicore aluminium conductor XLPE insulated PVC

sheathed armoured cable as per IS: 7098:1988 (Part-I) with upto date

amendments etc. complete as required. Tagging on both the ends will be

done with aluminium tags etc. complete as required.(Quantities as per

site requirement shall be finally estimated & executed accordingly with

prior approval.)

a) 3 core x 16 sqmm Al. Ar. XLPE Cable (Fire Fighting MCC Panel to Terrace

4 Supplying and making indoor end termination with brass compression

gland (Heavy duty) and suitable copper / aluminium lugs for following

size of XLPE insulated PVC sheathed copper/ aluminium conductor

armoured/ unarmoured cable of 1.1 KV grade including cost of ferrules,

cable sockets, insulation tape & other accessories etc. complete as

Supply and installing of following size of perforated hotdip G.I. cable

trays including horizontal and vertical bends, reducers, tees, cross

members and other accessories as required and duly suspended from the

ceiling with full threaded GI suspenders, along the wall with supports

and including painting etc. as required & approved by thye Engineer

Incharge.(Make: Saimetal/ Indeana/ Profab)

a) 100 mm width x 40 mm depth x 1.6 mm thickness Mtr 40.00 410.64 16425.60

6 Providing, laying, testing & commissioning of 'C' class heavy duty MS

Pipe conforming to lS 3589 and 1239 including fittings like elbows, tees,

flanges, tapers, nuts bolts, gaskets etc.,fixing the pipe on the wall/ceiling

with proper core cutting & filling with treatment, providing proper

supports, using clamps and painting with two or more coats of synthetic

enamel paint of required shade complete as required.

a) 100mm dia (Heavy class) as per IS-1239(Part-I)/2004 Mtr 10.00 2993.66 29936.60

b) 65mm dia (Heavy class) as per IS-1239(Part-I)/2004 Mtr 50.00 1321.60 66080.00

c) 25mm dia (Heavy class) as per IS-1239(Part-I)/2004 Mtr 5.00 729.24 3646.20

Digitally signed by JAYA

Sl No Item Description Unit Qty Rate Amount

7 Providing, fitting & fixing of following size cast iron double flanged slim

seal wafer type Butterfly valves with EPDM rubber lined with lever

operated as per IS-13095 with ISI mark of pressure ratting PN-1.60

including fixing the same with supply of required jointing materials like

rubber insertion, MS nuts & bolts, paint etc. and testing the joints with

required water pressure for all floors etc. all complete as per specification

& direction of E.I.C.

Providing, fitting & fixing of following size cast iron double flanged Y type

strainer with SS 304 perforated screen confirming to IS 1538 with ISI

mark of pressure rating PN-1.60 including fixing the same with supply of

required jointing materials like rubber insertion, MS nuts & bolts, paint

etc. and testing the joints with required water pressure & all complete as

per specification & direction of E.I.C.

9 Providing, fixing, testing and commissioning of following size cast iron

double flanged type Non Return Valve as per IS- 5312 (Part 1): 2004

with ISI mark of pressure ratting PN-1.60 including fixing the same with

supply of required jointing materials like flanges, rubber insertion, MS

nuts & bolts, paint etc. and testing the joints with required water

pressure etc. all complete as per specification & direction of E.I.C.

10 Providing, fixing, testing and commissioning of 25 MM C.I. single Air

Relief Valve with stop cock confirming to IS:14845/2000 with ISI mark

for water works purpose including fixing the same with hydrant riser

including testing & commissioning the system etc. all complete as per

approved specification & direction of EIC. Nos 1.00 3304.00 3304.00

11 Providing, fixing, testing and commissioning of 25MM SS Ball Valve

suitable for test pressure of not less than 15kg/sqcm with nuts, bolts,

gaskets, necessary accessories etc. all complete as per approved

specification & direction of EIC. Nos 4.00 2230.20 8920.80

12 Supply, Installation, Testing & Commissioning of Pressure gauge of 0-16

Kgf/sq.cm. range with cut-off bronze ball valves below of suitable size

with all accessories as per direction of Engineer-in-charge.

13 Supply, Installation, Testing & Commissioning of Swinging pattern wall

fixing first aid hose reel made from MS sheet and waterways and moving

parts with rubber hose of 20 mm dia. and 30 mtrs. long with ABS(Plastic)

shut-off nozzle as per IS: 444/IS: 12585 Type-I., complete with all

accessories as per direction of Engineer-in-charge.

FIRE EXTINGUISHER

Note : [1] All Fire Extinguisher shall be HCFC, CFC and Halons free. [2]

The Fire Extinguisher Manufacturer/Supplier shall provide declaration,

Technical Data Sheet/cutsheet of All type of Fire extinguisher to be

14 Providing and fixing Carbon-di-oxide fire extinguishers consisting of

welded M.S cylindrical body,squeeze lever discharge valve fitted with

internal discharge tube, ISI marked high pressure discharge hose,

discharge nozzle, suspension bracket, confirming to IS : 15683 finished

externally with red enamel paint and fixed to wall with brackets with

rawl plug/dash fasteners complete with internal charge with CO2 gas

conforming to IS : 307-1996..

15 Providing and fixing ABC stored pressure dry chemical powder (mono

ammonium phosphate) Fire Extinguisher IS : 15683 latest revision

manufacturer and of CRCA sheet in welded construction, finish with High

quality epoxy polyster powder coated complete with brass forged ball

valve, gun metal cap and nozzle, including initial filled and wall

suspension bracket (suitable for fighting in class 'A', B & 'C' that is wood,

textile, flammable liquid, electric and gases).

B MISCELLANEOUS WORK :

16 Single sided EXIT LED Light fitting signage(both side visible) with built in

battery back-up for 2 hrs with proper wiring with PVC conduiting from the

existing power sources for all floors etc. Each 3.00 6490.00 19470.00

Supply,installation, testing and commissioning of 36 Channel DVR 1080P

with 2 Sata Ports upto 10TB each, 32 BNC interface, supporting coaxitron

connection. HDTVI input of 4MP@30fps, 4MP@25fps, AHD input 4MP

1080p@25fps with 1CVBS output, 1HDMI output, 1VGA output, 1 audio

input, 1oudio output. Video compression of H.265 pro+/H.265

2 Supply,installation, testing and commissioning of 4 MP Dome / Bullet

Camera with 25 Mtrs IR Range. Nos 23.00 8850.00 203550.00

3 Supply & Laying of RG59+ 3 Core cable using Rigid PVC Pipe in concealed

Mtr 330.00 Digitally

82.60 signed by27258.00

manner per running metre of cable laid. PRAKASH GURU

Sl No Item Description Unit Qty Rate Amount

4 Supply,installation, testing and commissioning of BNC & DC Connectors.

5 Supply,installation, testing and commissionining of 8 TB CCTV

Surveillance Hard Disk. Nos 2.00 23600.00 47200.00

6 Supply,installation, testing and commissionining of 10 Amps Power

7 Supply,installation, testing and commissioning of Smart 32" LED Monitor.

8 Supply,installation, testing and commissioning of 10 Mtrs HDMI Cable.

9 Supply,installation, testing and commissioning of Bird Canopy. Nos 23.00 885.00 20355.00

10 Supply,installation, testing and commissioning of Wireless Mouse. Nos 1.00 885.00 885.00

11 Supply,Installation,Testing & Commissioning of 6U/500D Wall Mount

Rack with Accessories: The rack size should be 600W x 500D, Front

frame integrated with top, bottom, front and two side panels for better

rigidity and strength, Front Glass Door with Lock loaded, Compliance with

standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 ,

IEC EN 60068-2-11 , ISO 9001:2008 including Power Distribution Unit

(06/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw

Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with

Power Cable 2.5 sq.mm 3 meter Lengt), 1 cooling Fan(230V AC - 90

CFM, dB 42), 2nos 1U Metal Cable manager with Plastic cable loops and

Digitally signed by JAYA

Description Unit Qty Rate Amount

1 A- Internal Sanitary & Plumbing System

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes conforming to IS:15778/ASTM Pipe, having thermal

stability for hot & cold water supply, including all CPVC

plain & brass threaded fittings including fixing the pipe

with clamps at 1.00 m spacing. This includes jointing of Mtr 25 338.13 8453.23

pipes & fittings with one step CPVC solvent cement and

testing of joints complete as per direction of Engineer-in-

In ground floor

20mm dia C-PVC Pipes Mtr 15 377.03 5655.50

2 25mm dia C-PVC Pipes

3 32mm dia C-PVC Pipes Mtr 5 661.63 3308.13

4 In First Floor

20mm dia C-PVC Pipes

5 25mm dia C-PVC Pipes Mtr 20 461.40 9228.07

6 32mm dia C-PVC Pipes Mtr 10 677.62 6776.15

7 40mm dia C-PVC Pipes Mtr 5 914.38 4571.91

8 In Second Floor

20mm dia C-PVC Pipes

9 25mm dia C-PVC Pipes Mtr 20 475.41 9508.20

10 32mm dia C-PVC Pipes Mtr 10 693.59 6935.92

11 40mm dia C-PVC Pipes Mtr 5 934.87 4674.33

12 In Terrace Floor

32mm dia C-PVC Pipes

13 40mm dia C-PVC Pipes Mtr 20 955.40 19107.98

14 50mm dia C-PVC Pipes Mtr 10 1412.09 14120.94

15 Supplying all materials, labour, T&P and fitting and fixing

U-PVC SWR soil waste ventilating pipes and fittings of the

following outside diameter conforming to ISI No.

13592/1992 to walls with nails, bobbins and wooden plugs

or laying in trenches including jointing with supply of

approved rubber lubricant by non-heat application Mtr 85 399.19 33931.49

method/as per manufacturer ’ s specification, testing,

earthwork in excavation in all kinds of soil and refilling of

trenches as per specification and direction of the Engineer

in charge. (Supreme, Astral, Ashirbad) .

16 75mm PVC plain bend Each 20 217.12 4342.40

17 75mm PVC socket plain Each 30 95.93 2878.02

20 110mm PVC socket plain Each 20 188.92 3778.36

21 110mm PVC plain bend Each 25 273.76 6844.00

22 110mm PVC door bend Each 6 346.45 2078.69

23 110mm PVC door Tee Each 6 455.48 2732.88

24 110mm PVC plain Tee Each 30 380.79 11423.58

25 110mm PVC door cross Tee Each 4 650.42 2601.66

26 110mm dia U-PVC Offset without ear Each 2 480.73 961.46

27 110mm PVC vent cowl Each 11 68.68 755.44

28 110mm PVC Clamp Each 30 50.50 1515.12

29 Supply,Providing, fixing, testing and commissioning in

position UV stabilised 75 mm dia UPVC Rain water pipe

with Fittings (IS: 13592 Type - B). In case of ceiling Mtr 20 419.16 8383.19

hanging, the supply of Pipe Clamps (Chilly/MS angle) as

per engineer in charge.110 mm diameter. (IS:13592,

Type -B). Digitally signed by JAYA

Description Unit Qty Rate Amount

30 Supply,Providing and fixing 150 mm x 150 mm.dia CI

Grating for Rain water pipes 110 mm dia.

31 Supplying all materials , labour, T&P and fixing Vitreous

china water closet ,squatting pan ( Indian type W.C. pan

/ Orissa pattern squatting pan ) duly embedded in cement

concrete 1:5:10 using hard granite metal 4cm nominal

size including fixing a pair of vitreous china

250mmx130mmx30mm foot rest, fixing 100mm dia hci 'P'

or 'S' trap for water closet squatting pan including jointing

the trap with pan in cement mortar (1:1), cutting the floor

and mending good the damages etc. all complete as per

P.H. specification and direction of Engineer-in-charge .

580mmx440mm size Orissa Pan (White) (Parryware/

Hindware/ Somay/ Cera)

32 Supplying all materials,labour,T&P and fitting and fixing

vitrous Chaina washed down water Closet (European type

water closet - EWC) with integral "P" or "S" type trap to

the floor including wodden plug and chromoum plated

screw including jointing the trap with soil pipe in CM(1:1)

fixing plastic seat cover for washed down water closet Each 11 3289.84 36188.24

with crmium plated brass hinges and rubber buffers

including polishing etc all complete as per specification

and direction of Engineer-in-charge.

European Water Clost "S" or "P" trap (Parryware/

Hindware/ Somany/ Cera)

33 Matrix Set -1 (WB 65 x 35 with one pair mounting

brackets, EWC & Cistern complete with fittings & seat Each 1 78575.49 78575.49

cover, one no hinged rail 76 cm and five nos of grab rails

60 cm) (Hindware).

34 Supplying all materials, labour, T&P and fitting and fixing

10 litres capacity low level flushing cistern with a pair of

cast iron or M.S brackets complete with fittings such as

siphonic arrangements 15mm nominal size brass/pvc ball

valve with polythene float CP brass handle, unions and

couplings for connection with inlet, outlet and overflow

pipes,32mm dia CP flush bend,15mm dia pvc inlet Each 21 1851.77 38887.25

connection pipe including cutting holes and making good

the same and connecting the flush bend with cistern and

closet and connecting the inlet pipe with supply main etc

all complete as per specification and direction of the

Engineer in charge.

10 litres PVC L.L. Cistern (Slimline-white)

35 32mm dia flush bend for L/L cistern Each 21 81.77 1717.25

Digitally signed by JAYA

Description Unit Qty Rate Amount

36 Supplying all materials ,labour ,T&P and fixing Wash

basin with hole for pillar taps with cast iron or MS brackets

painted white including cutting holes in walls and making

good the damages with supply of wooden plugs, screws

and cement etc. fixing pedestral for wash basin recessed

at the back for the reception of pipes and fittings, fixing

PVC waste pipe of 32mm nominal diameter for wash basin

including brass check nut complete, fixing pillar taps

capstan head screw down high pressure lettered 'Hot' and Each 5 4843.90 24219.50

'Cold' with long screws, shanks and back nuts of 15mm

dia nominal bore, fixing15mm dia PVC inlet connection

pipe and making connection with pillar cocks and supply

mains for wash basin , fixing 12mm dia CP brass waste

etc.all complete as per specification and direction of

Engineer-in-charge.

550mmx400mm size wash hand basin with Porcelain

pedestal(Parryware/Hindware/Somay/Cera)

Under Counter basin (560x450) (Hindware) Each 20 3319.34 66386.80

37 32mm dia PVC waste pipe with brass coupling nut Each 25 62.58 1564.39

38 15mm dia PVC inlet connection pipe 0.45m long Each 25 42.13 1053.15

Digitally signed by JAYA

Description Unit Qty Rate Amount

39 Supplying all materials, labour, T&P and fixing wash

Kitchen sink/ Laboratory sink with outlet at end and weir

overflow including fitting and fixing a pair of cast iron or

MS brackets painted white, fixing 50mm/40mm dia ss

waste, fixing 50mm/40mm dia PVC waste pipe 910mm

long with supply of wooden plugs, screws and cement etc Each 3 6271.07 18813.22

including cutting holes in walls and making good the

damages etc all complete as per specification and

direction of the Engineer in charge. 600x450x250 mm

stainless steel kitchen sink (Jayna make)

40 Supplying all materials, labour, T&P and fitting and fixing

brass/CP fittings of the following nominal bore with supply

of all jointing materials complete as per specification and Each 11 1085.60 11941.60

direction of the Engineer in charge.

15mm dia CP 2way bib cock (Euronics RIV-1004R)

41 15mm dia CP Health faucet with Hose Pipe (Euronics

42 15mm dia CP Short Body Bib cock (Euronics RIV-1010R)

43 15mm dia CP Long Body Bib cock (Euronics RIV-1011R)

44 15mm dia CP Angle stop cock with wall Flange (Euronics

45 15mm CP Revolving shower with shower Arm. ( Plaza

46 20mm dia CP Consealed Stop Cock (Jaquar ALD-CHR-081

47 Sink Cock (Wall Mounted) with wall Flange(Euronics RIV-

48 15mm dia CP Pillar cock (Euronics RIV-1002R) Each 25 1096.22 27405.50

49 15mm dia CP extension piece Each 50 69.97 3498.70

50 PVC Connection Pipe Each 46 40.12 1845.52

51 PVC Discharge Pipe Each 27 92.75 2504.20

52 15mm dia. C.P flange Each 70 47.55 3328.78

53 125mm dia CP gratting Each 52 110.33 5737.16

54 Supplying all materials ,labour ,T&P and fixing standard

sized CP brass towel rail / Towel ring complete with CP

brass brackets fixed to wooden plugs with chromium

plated brass screws etc.all complete as per specification Each 20 924.92 18498.39

and direction of Engineer-in-charge .

25mmx600mm long CP Towel rail

55 C P Towel Ring Each 15 636.48 9547.20

56 Supplying all materials ,labour ,T&P and fixing CP Soap

Holder/ Soap Dispenser complete with CP brass brackets

fixed to wooden plugs with chromium plated brass screws Each 20 262.05 5241.09

etc.all complete as per specification and direction of

Engineer-in-charge .

57 CP soap dispenser Each 18 2713.54 48843.72

58 Supplying all materials, labour, T&P and fixing of Stainless

Steel Coat Hook alongwith all necessary accessories

complete including cutting, making good the walls, floors,

slab wherever complete in all respect as per specification Each 17 342.20 5817.40

and direction of the Engineer in charge. (Jaquar/

Hindware/ Cera) .

Stainless Steel Coat Hook - Double (Euronics EC02) Digitally signed by JAYA

Description Unit Qty Rate Amount

59 Supplying all materials ,labour ,T&P and fixing Mirror of

superior glass mounted on 6mm thick A.C. sheet or ply

wood sheet and fixed to wooden plugs with chromium

plated brass screws and washers etc.all complete as per Each 25 939.16 23479.05

specification and direction of Engineer-in-charge.

Mirror (Bevelled edge) 600mmx450mm

60 Supplying all materials, labour, T&P and fitting and fixing

G.M/ Brass fittings of the following nominal bore with

supply of all jointing materials complete as per Each 10 1168.51 11685.07

specification and direction of the Engineer in charge.

25mm dia Brass F.W valve (Sakti make)

61 32mm dia Brass F.W valve (Sakti make) Each 2 1711.44 3422.87

62 40mm dia Brass F.W valve (Sakti make) Each 4 2165.41 8661.62

63 40mm dia CPVC Ball valve Each 5 1116.34 5581.70

64 Supplying all materials, labour, T&P and providing fitting

and fixing (Aqua guard) Pure Chill 80 PSS UV of size

750x570x1350mm height with water storage capacity 80

liters along with 2 nos of faucets 1 for cold water and 1 for

normal water including a flow of 1.5 ltr per minute etc all Each 3 132445.56 397336.68

complete as per approved drawing,specification and

direction of the Engineer in charge.

Pure Chill 80 PSS UV Make-Aquaguard/Usha

65 Supplying all materials,labour,T&P and fixing Rotational

moulded polyethylene cylindrical vertical water storage

tanks conforming to IS : 12701--1996 including cutting

holes through the tank and fixing mild steel tubes and

fittings and providing extra sockets and jam nuts, fixing

ball valve etc, including hoisting upto a height of 5 metres

above ground level and placing the tank to the required

position and providing 1st class K.B brickwork in cement

mortar (1:6) of 0.46m height in staging and in circular

protection wall to support the tank, 12mm thick cement Each 1 56731.21 56731.21

plaster (1:6) over brickwork, R.C.C slab of size

1.60mx1.60m and 0.10m thick, R.C.C beam of

0.25mx0.30m and 2.60m average length in cement

concrete(1:2:4) using 12mm size h.g chips including

centering and shuttering, watering, curing, conveyance of

all materials to worksite etc all complete as per

specification and direction of the Engineer in charge.

Fixing 3000Ltr Roto-moulded water storage tanks-In

66 B- External Supply & Discharge portion

Supplying all materials ,labour ,T&P and constructing gully

trap chamber of inside size 250mmx250mm with 8cm

thick RCC precast cover slab in cement concrete (1:2:4)

mix using 12mm size crusher broken HG chips, foundation

concrete (1:4:8) using 40mm size crusher broken HG

metal on bed and around trap, KB brick work in cement

mortar (1:6) in foundation and plinth and inside 12mm

thick cement plastering (1:3) finished with a floating coat

of neat cement including fixing 100mmx100mm size HCI

gully trap, 150mmX150mm size CI grating etc.all

complete as per drawing, specification and direction of

Engineer-in-charge.

In side size 250mmx250mm Digitally signed by JAYA

Description Unit Qty Rate Amount

67 Supplying all materials ,labour ,T&P and constructing

Inspection Chamber of inside size

760mmx760mmx460mm with cement concrete (1:3:6)

using 40mm size crusher broken hard black granite metal

on bed , KB brick work in cement mortar (1:6) in

foundation and plinth, moulding and shaping the channel

inside and benching with cement concrete (1:2:4) using

12mm size crusher broken hard black granite chips,

12mm thick cement plaster (1:3) with cement punning to

inside, cement flush pointing (1:3) to outside, R.C.C cover each 8.00 13806.18 110449.42

slab (1:2:4) using 12mm size crusher broken hard black

granite chips with R.C.C man hole cover, earth work in

excavation in all kinds of soil and refilling the cavity

around the chamber including watering,curing,cost of all

materials, conveyance of all materials to worksite,

payment of royalty,all taxes etc.all complete as per

approved drawing, P.H specification and direction of

Engineer-in-charge .

Inside size : 760mmx760mmx460mm

68 Providing Lowering, Laying, Jointing and Testing Work of

non-pressure NP 3 class R.C.C. pipes with collars jointed

with stiff mixture of cement mortar in the proportion of Mtr. 80.00 532.42 42593.28

1:2 (1 cement : 2 fine sand) including testing of joints:

69 E- Construction 1 nos 100 users RCC Septic tank

Earth work in excavation of foundation in all kinds of soil

within 50m initial lead and 1.5m initial lift including rough

dressing & breaking clods to maximum 5cm to 7cm and cum 59.4 344.206 20445.84

laying in layers not exceeding 0.3m in depth and as per

direction of the Engineer-in-Charge.

70 - do - with addl. Depth of 1.5 m

71 Supplying all materials,labour ,T&P and filling in

foundation and plinth with sand well watered and rammed

including cost, conveyance of all materials to work site cum 5.94 1194.986 7098.22

,payment of royalty,taxes etc. all complete as per

direction of the Engineer-in -charge.

In ground floor- 1x9.90mx4x0.15m=

72 Supplying all materials, labour, T&P and providing cement

concrete ( 1:4:8 ) with 4cm size crusher broken hard

granite metal including watering, curing, cost of all

materials,conveyance of all materials to work site with cum 5.94 7051.798 41887.68

payment of royalty, all taxes etc all complete as per P.W.D

specification and direction of Engineer-in-charge.

In ground floor- 1x9.90mx4x0.15m=

73 Supplying all materials, labour, T&P and providing cement

concrete ( 1:2:4 ) with 12mm size crusher broken hard

black granite chips including watering, curing,cost of all

materials, conveyance of all materials to work site with cum 3.47 9391.62 32598.31

payment of royalty, all taxes etc all complete as per P.W.D

specification and direction of Engineer-in-charge.

In ground floor- 1x8.90mx3x0.13m=

Digitally signed by JAYA

Description Unit Qty Rate Amount

74 Supplying all materials, labour, T&P and providing cement

concrete (1:1:5:3) with 12mm size hard broken granite

chips for R.C.C works including hoisting, laying, watering,

curing, conveyance of all materials to worksite, payment cum 27.87 10255.498 285820.73

of royalty, taxes etc all complete as per specification and

direction of the Engineer in charge.

75 Supplying all materials, labour, T&P and providing rigid

and smooth centering and shuttering for R.C.C works

including false work and dismantling them after casting

including conveyance of all materials to worksite, payment sqm 37.15 889.248 33035.56

of royalty, taxes etc all complete as per specification and

direction of the Engineer in charge.

A. For Roof slab

76 Supplying all materials, labour, T&P and providing M.S

reinforcement for R.C.C work including cutting, bending,

binding, and tying the grills and placing in position

including cost of binding wire 18 to 20 gauge, conveyance Qntl 22.3 10351.786 230844.83

of all materials to worksite, payment of royalty, taxes etc

all complete as per specification and direction of the

Engineer in charge.

In ground floor

77 Supplying all materials,labour,T&P and providing 6mm CP

(1:4) with cement punning on brick work including

watering,curing,cost of all materials, conveyance of all

materials to worksite,payment of royalty,all taxes etc.all sqm 83.82 297.95 24974.17

complete as per PWD specification and direction of the

Engineer-in-charge.

78 Supplying all materials, labour, T&P and providing,fitting

and fixing 100mm x 100mm x 100mm SW Tee in wall

including filling the recess with cement concrete (1:3:6)

with 12mm size h.g chips all complete including watering, Each 2 542.092 1084.18

curing, conveyance of all materials to worksite, payment

of royalty all complete as per specification and direction

of the Engineer in charge

79 Supplying all materials, labour, T&P and making MS step

iron in 20mm diameter MS steel bars and fixing into walls

of man hole/septic tank duly embedded in cement Each 10 335.592 3355.92

concrete (1:3:6) complete as per specification and

direction of the Engineer in charge.

80 Filling in foundation and plinth with excavated materials,

moorum including watering and ramming as directed by cum 10 191.278 1912.78

the Engineer in charge.

Digitally signed by JAYA

Description Unit Qty Rate Amount

81 Supplying all materials, labour, T&P and constructing

soakway pit of the following size with dry brick walling

from bottom upto invert of inlet pipe and fly ash brickwork

in cement mortar (1:6) for the remaining height at top,

cement concrete (1:4:8) using 40mm size hg chips on

bed, 12mm thick cement plaster (1:4) inside and outside

over masonry brickwork, gravel backing in the rear of well

steining, RCC cover slab in cement concrete (1:2:4) using

12mm size hg chips fitted with iron lifting handles

including earthwork in open well excavation in all kinds of

soil and refilling of cavity around the pit & painting the

iron works, watering, curing, conveyance of all materials

to worksite, payment of royalty, taxes etc all complete as

per approved specification and direction of the Engineer in

charge 1.40m dia x 2.00m deep soakway pit .

Digitally signed by JAYA