REPAIR/MAINTENANCE OF PUMP SET, MOTORS, STARTER, CLARIFLOCULATOR INCLUDING PANEL BOARDS AND MISC WORKS AT VARIOUS WATER SUPPLY INSTALLATIONS UNDER GE MISAMARI

Amount

Servicing/Overhauling of 3 Phase 415 Volts 1440 RPM 150 HP/125 HP capacity Induction Motor (MAKE : KIRLOSKAR/ ALSTOM) installed at Jalkendra, Intermediate Pump House alongwith following others repairs :- (a) Taking out Motor from its Position by decoupling from Pump and disconnecting all Cable Connections. (b) Dismantaling of induction Motor complete Part by Part carefully, testing all Coils, degreasing bearing and display all the Parts without damaging any portion for inspection of Engineer-in-Charge to ascertain the Serviceability of existing Parts. (c) Heating & Varnishing to Stator with super quality varnish and dried out properely with external heat as ordered and as directed. (d) Reassembeling the Motor complete with all existing Serviceable Parts obtained against Item 1(b), greasing the Bearing with bearing grease and new Parts as ordered by Engineer-in-Charge (New Parts shall be measured and paid separately under relevant Item here-in after) (e) Reinstall the Motor at its existing Position, couple with the Pump connecting all Cable connections and testing on completion complete all as specified and as directed. (NOTE: For Note description refer APPENDIX "A")

Supply only DE ( Driver End ) Bearing No- NU318C3 or as per existing size Make- SKF, TATA suitable for 150 HP Motor against Item No. 1 here-in-above, complete all as specified and as directed.

Supply only NDE ( Non Driver End ) Bearing No- 6314C3 or as per existing size Make- SKF, TATA suitable for 150 HP Motor against Item No. 1 here-in-above, complete all as specified and as directed.

Supply only Bakelite connection terminal plate with brass nuts bolts and washers suitable for 150 HP Motor against Item No. 1 here-in-above, complete all as specified and as directed.

Rewinding burnt coils of Induction Motor stator of capacity 125 HP /150 HP obtained from Item Ser No-1 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding, cleaning/ repairing damaged slots, complete all as specified and as directed.

Servicing / Overhauling of Electric driven Vertical / Horizontal NC split casing Pump-set having discharge 50000 GPH/ 60000 GPH, H 61-M ( Make- Kirloskar ) coupled with induction Motor 125HP/ 150 HP capacity installed at Jalkendra, Intermediate Pump house along with following others repairs :- a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b). Dismantaling of Pump complete part by part carefully , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in-Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope. d). Reassembeling the Pump complete with all existing serviceable parts obtained against Item 6(b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position, couple with the Motor and connecting all suction delivery water connections and testing on completion complete all as specified and as directed. (NOTE: For Note description refer APPENDIX "A")

Supply only DE ( Driver End ) bearing as per existing size Make- SKF/TATA NO 6314ZZ/6309ZZ (Heavy Duty) (PROVISIONAL) of Horizontal Split casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed.

Supply only NDE ( Non Driver End ) bearing as per existing size Make- SKF/TATA NO 7316ZZ/3309ZZ/22315 ZZ( Heavy Duty), ( PROVISIONAL) of Horizontal Split casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed.

Supply only SS Pump Shaft sleeve for Pump shaft (PROVISIONAL) of Horizontal Split casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed.

Supply only Rubber Star Coupling (PROVISIONAL) of Horizontal Split casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed.

Supply only Rubber Tyre Coupling UNIOUE -PX-100 (PROVISIONAL) of Horizontal Split casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed.

Supply only CI Impeller Horizontal Split casing Pump (PROVISIONAL) of Horizontal casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed.

Supply only Pump Shaft (PROVISIONAL) of Horizontal casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed.

Supply only Oil Seal (PROVISIONAL) of Horizontal casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed.

Supply only/ Topping up Engine Oil (20W50) (PROVISIONAL) of Horizontal casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed.

Welding Turning and machining works of Pump Shaft obtained from Item No 6 here-in-before to true size to match with the new Parts / existing serviceable parts for proper allignment and smooth operation of Motor Pump Set complete all as specified and as directed

Servicing / overhauling of 3 Phase 415 Volts 1440 RPM 75 HP capacity induction (Motor Make-Jyoti, Kirloskar, Becon ) Installed at Jalkendra Pump House, Old pump House, along with following others repairs :- a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantaling of induction Motor complete part by part carefully , testing all coils , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed. d). Reassembeling the motor complete with all existing serviceable parts obtained against Item 19(b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge. (New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion complete all as specified and as directed. (NOTE: For Note description refer APPENDIX "A")

Supply only DE ( Driver End ) Bearing No- NU314 / N 344 or as per existing Make- SKF, TATA of Induction Motor against Item No-19 here-in-above complete all as specified and as directed.

Supply only NDE ( Non Driver End ) Bearing No - 6313 / 6311 or as per existing size Make- SKF, TATA of Induction Motor against Item No-19 here-in-above complete all as specified and as directed.

Supply only Bakelite connection plate with brass nuts bolts and washers ( PROVISIONAL) of Induction Motor against Item No-19 here-in-above complete all as specified and as directed.

Rewinding burnt coils of Induction Motor stator of capacity 75 HP obtained from Item Ser No-19 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding, cleaning/ repairing damaged slots, complete all as specified and as directed.

Servicing / over hauling of Electric driven Multi staging Pump set having discharge Cap 40000 GPH, H-61 M (Pump Make-BE, Alstom ) Installed at Jalkendra , Old pump House coupled with induction Motor 75 HP capacity along with following others repairs :- a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b) Dismantaling of Pump complete part by part carefully , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope . d). Reassembeling the Pump complete with all existing serviceable parts obtained against Item 10 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery water connections and testing on completion complete all as specified and as directed. (NOTE: For Note description refer APPENDIX "A")

Supply only DE ( Driver End ) bearing as per existing size Make- SKF/TATA 6307ZZ ( heavy duty) of 75 HP Motor to incorporate against Item No-24 here-in-above complete all as specified and as directed.

Supply only NDE ( Non Driver End ) bearing as per existing size Make- SKF/TATA 6306/6307 ( heavy duty) of 75 HP Motor to incorporate against Item No-24 here-in-above complete all as specified and as directed.

Supply only SS Pump Shaft sleeve for Pump shaft of 75 HP Motor to incorporate against Item No-24 here-in-above complete all as specified and as directed.

Supply only CI Impeller as per Existing of 75 HP Motor to incorporate against Item No-24 here-in-above complete all as specified and as directed.

Supply only Pump Shaft of 75 HP Motor to incorporate against Item No-24 here-in-above complete all as specified and as directed.

Supply only Rubber Tyre Coupling complete set UNIQUE -PX-90 of 75 HP Motor to incorporate against Item No-24 here-in-above complete all as specified and as directed.

Supply only CI coupling tyre only UNIQUE PX-90 of 75 HP Motor to incorporate against Item No-24 here-in-above complete all as specified and as directed.

Welding Turning and machining works of Pump Shaft obtained from Item No 22 here-in-Before to true size to match with the new Parts / existing serviceable parts for proper allignment and smooth operation of Motor Pump Set complete all as specified and as directed

Servicing / Overhauling of Electric Motor Vertical 3 Phase 415 Volts 1440 RPM capacity 50 HP / ( Make- Kirloskar/ Alstom ) . installed at Jalkendra, along with following others repairs :- a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections. b) Dismantaling of induction Motor complete part by part carefully , testing all coils , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed. d). Reassembeling the motor complete with all existing serviceable parts obtained against Item 28(b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion complete all as specified and as directed. (NOTE: For Note description refer APPENDIX "A")

Supply only DE ( Driver End ) bearing or as per existing size Make- SKF/TATA 6407 ZZ ( heavy duty) of Vertical Electric Induction Motor against Item No-31 here-in-above complete all as specified and as directed.

Supply only NDE ( Non Driver End ) Bearing or as per existing size Make- SKF/TATA 6408ZZ ( heavy duty) of Vertical Electric Induction Motor against Item No-31 here-in-above complete all as specified and as directed.

Supply only Bakelite connection plate with brass nuts bolts and washers suitable for Motor cap 50 HP of Vertical Electric Induction Motor against Item No-31 here-in-above complete all as specified and as directed.

Servicing / over hauling of Electric driven Multi staging Pump set having discharge Discharge-2040 LPM, H-55 M (Pump Make-Becon ) Installed at Old Pump, coupled with induction Motor 50 HP capacity along with following others repairs. a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b).Dismantaling of Pump complete part by part carefully , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope . d). Reassembeling the Pump complete with all existing serviceable parts obtained against Item 15 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery water connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of Pump coupled with HP 50 Motor Motor to incorporate against each Item No-35 here-in-above DE ( Driver End ) bearing as per existing size Make- SKF/TATA 6309ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of Pump coupled with HP 50 Motor Motor to incorporate against each Item No-35 here-in-above NDE ( Non Driver End ) bearing as per existing size SKF/TATA 3309ZZ ( heavy duty)

Welding Turning and machining works of Pump Shaft obtained from Item No 15 here-in-Before to true size to match with the new Parts / existing serviceable parts for its proper functioning and allignment all as required and directed for smooth functioning of Motor Pump Set

Servicing / over hauling of Electric Motor Vertical 3 Phase 415 Volts 1440 RPM capacity 40 HP / ( Make- Jyoti, CVO) . installed at Jalkendra , along with following others repairs. a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantaling of induction Motor complete part by part carefully , testing all coils , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c) Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed d). Reassembeling the motor complete with all existing serviceable parts obtained against Item 18 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of Vertical Electric Induction Motor to incorporate against each Item No-39 here-in-above DE ( Driver End ) Bearing as per existing Make- SKF/TATA 6314/6311ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of Vertical Electric Induction Motor to incorporate against each Item No-39 here-in-above NDE ( Non Driver End ) Bearing Make- SKF/TATA 7316ZZ/6310ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of Vertical Electric Induction Motor to incorporate against each Item No-39 here-in-above Bakelite connection plate with brass nuts bolts and washers

Rewinding burnt coils of Vertical Electric Induction Motor stator cap 40 HP obtained from Item Ser No-18 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete as directed

Servicing / over hauling of Vertical Turbine Multi staging Pump installed Inslde Jackwell coupled with 40 HP Vertical Motor at Jalkendra along with following others repairs. a). Decoupling Vertical Motor from Pump shaft and disconnecting all suction /delivery water connections , setting aside Motor from base plate , Lifting column pipes and submersible multistaging Pump set from Jackwell ,setting aside and stacking column pipes for reuse complete all as directed by Engnr-in-Charge. b).Dismantaling of Pump complete part by part carefully , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope . d). Reassembeling the Pump complete with all existing serviceable parts obtained against Item 21 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Lowering column pipes and submersible multistaging Pump set inside Jackwell ,connecting Suction/ delivery Lines including replacement of nuts bolts , washers and rubber gasket f) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above CI Impeller

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above Impeller Collet

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above GM Bowel Bushing

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above Stain Less Steel (SS) Line Shaft 10'- Long

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above Stain Less Steel (SS) Top Shaft ( Motor Shaft)

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above SS Spider Guide Shaft Sleeve

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above SS lline/pump Shaft Coupler/ reduce Socket

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above SS lline Shaft Coupler/Socket

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above CI Shaft Spider Guide ( 8") dia

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above Suction Case

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above Discharge Case

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above Impeller centre Bowl

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above Impeller Top Bowl

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above VT Pump strainer

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above Bowl studs

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above MS heavy duty column Pipe 200 mm Bore both ends flanged (3.0 Meter Long )

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above MS heavy duty 200mm dia flange only

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above MS Nut bolts with washers 5/8 dia and 3"/6" long

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above MS Nut bolts with washers 1/2" dia and 3" long

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Pump coupled with 40 HP Vertical Motor to incorporate against each Item No-44 here-in-above Rubber gasket 4/6 mm thick

Servicing / over hauling of 3 Phase 415 Volts 1440 RPM 20 HP (Motor Make--Kirloskar ) Installed at AIR OP pump House ,Old pump House, Swimming Pool, Rekhamari , coupled with NC Horizontal Pumping Set a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantaling of induction Motor complete part by part carefully , testing all coils , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c)., Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed d). Reassembeling the motor complete with all existing serviceable parts obtained against Item 23 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of 20 HP Motor to incorporate against each Item No-65 here-in-above DE ( Driver End ) bearing as per existing size Make- SKF/TATA no.6306ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of 20 HP Motor to incorporate against each Item No-65 here-in-above NDE ( Non Driver End ) Bearing as per existing size Make- SKF/TATA no.6307ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of 20 HP Motor to incorporate against each Item No-65 here-in-above Bakelite Terminal connection plate with brass nuts bolts and washers

Supply only the following Items ( PROVISIONAL) of 20 HP Motor to incorporate against each Item No-65 here-in-above Plastic Rotar Fan

Supply only the following Items ( PROVISIONAL) of 20 HP Motor to incorporate against each Item No-65 here-in-above Tyre coupling complete set No-60/70

Supply only the following Items ( PROVISIONAL) of 20 HP Motor to incorporate against each Item No-65 here-in-above Tyre coupling Rubber tyre only No-60/70

Rewinding burnt coils of Induction Motor stator cap 20 HP obtained from Item Ser No-23 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete as directed

Servicing / over hauling of Electric driven Horizontal split casing Pump set of Discharge cap 1230 LPM, H-30 M (Pump Make-Kirloskar , HBB) Installed at AIR OP pump House ,Old pump House, Swimming Pool, Rekhamari coupled with induction Motor 20 HP capacity along with following others repairs. a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b).Dismantaling of Pump complete part by part carefully , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope . d). Reassembeling the Pump complete with all existing serviceable parts obtained against Item 26 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery water connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of Pump coupled with 20 HP Motor to incorporate against each Item No-73 here-in-above DE ( Driver End ) bearing as per existing size Make- SKF/TATA no.6306ZZ/6307ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of Pump coupled with 20 HP Motor to incorporate against each Item No-73 here-in-above NDE ( Non Driver End ) bearing as per existing size Make- SKF/TATA no.6308ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of Pump coupled with 20 HP Motor to incorporate against each Item No-73 here-in-above SS Pump Shaft sleeve for Pump shaft

Supply only the following Items ( PROVISIONAL) of Pump coupled with 20 HP Motor to incorporate against each Item No-73 here-in-above CI Impeller as per Existing

Supply only the following Items ( PROVISIONAL) of Pump coupled with 20 HP Motor to incorporate against each Item No-73 here-in-above Pump Shaft

Welding Turning and machining works of Pump Shaft obtained from Item No 73 here-in-Before to true size to match with the new Parts / existing serviceable parts for proper allignment and smooth operation of Motor Pump Set complete all as specified and as directed

Servicing / over hauling of 3 Phase 415 Volts 1440 RPM 15 HP (Motor Make-Kirloskar ) Installed at Jalekendra Pump house a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantaling of induction Motor complete part by part carefully , testing all coils , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c)., Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed d). Reassembeling the motor complete with all existing serviceable parts obtained against Item 29 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of 15 HP Motor to incorporate against each Item No-80 here-in-above DE ( Driver End ) bearing as per existing size Make- SKF/TATA no.6306ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of 15 HP Motor to incorporate against each Item No-80 here-in-above NDE ( Non Driver End ) Bearing as per existing size Make- SKF/TATA no.6307ZZ/6308ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of 15 HP Motor to incorporate against each Item No-80 here-in-above Bakelite Terminal connection plate with brass nuts bolts and washers

Supply only the following Items ( PROVISIONAL) of 15 HP Motor to incorporate against each Item No-80 here-in-above Plastic Rotar Fan

Rewinding burnt coils of Induction Motor stator cap 15 HP obtained from Item Ser No-80 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete as directed

Servicing / over hauling of Electric driven Horizontal split casing Pump set of Pump Discharge 26.5 LPS, H-21.5M, (Pump Make-Kirloskar ,) Installed at Jalkendra Pump House coupled with 15 HP Motor along with following others repairs. a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b).Dismantaling of Pump complete part by part carefully , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope . d). Reassembeling the Pump complete with all existing serviceable parts obtained against Item 32 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery water connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-86 here-in-above DE ( Driver End ) bearing as per existing size Make- SKF/TATA no.6307ZZ/6306ZZ ( heavy duty

Supply only the following Items ( PROVISIONAL) of NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-86 here-in-above NDE ( Non Driver End ) bearing as per existing size Make- SKF/TATA no.6308ZZ ( heavy duty

Supply only the following Items ( PROVISIONAL) of NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-86 here-in-above SS Pump Shaft sleeve for Pump shaft

Supply only the following Items ( PROVISIONAL) of NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-86 here-in-above CI Impeller as per Existing

Supply only the following Items ( PROVISIONAL) of NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-86 here-in-above Pump Shaft

Supply only the following Items ( PROVISIONAL) of NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-86 here-in-above tyre Coupling complete set No.60

Supply only Star Rubber Coupling (PROVISIONAL) of NC Horizontal/ Vertical split casing Pump coupled with 10 HP Motor to incorporate against each Item No-83 here-in-above complete all as specified and as directed. tyre Coupling rubber only No.60

Welding Turning and machining works of Pump Shaft obtained from Item No 86 here-in-Before to true size to match with the new Parts / existing serviceable parts for proper allignment and smooth operation of Motor Pump Set complete all as specified and as directed

Servicing / over hauling of 3 Phase 415 Volts 1440 RPM 10 HP (Motor Make-Kirloskar , Jyoti , CG ) Installed at AIR OP pump House ,Old pump House, Rekhamari Pump House lama camp pump house. a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantaling of induction Motor complete part by part carefully , testing all coils , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c)., Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed d). Reassembeling the motor complete with all existing serviceable parts obtained against Item 35 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of 10 HP Motor to incorporate against each Item No-95 here-in-above DE ( Driver End ) bearing as per existing size Make- SKF/TATA no.6307ZZ/6308ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of 10 HP Motor to incorporate against each Item No-95 here-in-above NDE ( Non Driver End ) Bearing as per existing size Make- SKF/TATA no.SKF/TATA no.6307ZZ/6308ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of 10 HP Motor to incorporate against each Item No-95 here-in-above Bakelite connection plate with brass nuts bolts and washers

Rewinding burnt coils of Induction Motor stator cap 10 HP obtained from Item Ser No-95 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete as directed

Servicing / over hauling of Electric driven Horizontal split casing Pump set of Pump Discharge Centrifugal 10000 - GPH, H- 40M, 10 HP, (Pump Make-Kirloskar ,BE, Jyoti ) Installed at AIR OP pump House ,Old pump House, Rekhamari Pump House lama camp pump house. along with following others repairs. a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b).Dismantaling of Pump complete part by part carefully , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope . d). Reassembeling the Pump complete with all existing serviceable parts obtained against Item 38 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery water connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-100 here-in-above DE ( Driver End ) bearing as per existing size Make-SKF/TATA no.6308ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-100 here-in-above NDE ( Non Driver End ) bearing as per existing size Make- SKF/TATA no.6308ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-100 here-in-above SS Pump Shaft sleeve for Pump shaft

Supply only the following Items ( PROVISIONAL) of NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-100 here-in-above CI Impeller as per Existing

Supply only the following Items ( PROVISIONAL) of NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-100 here-in-above Pump Shaft

Supply only the following Items ( PROVISIONAL) of NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-100 here-in-above tyre Coupling complete set No.60

Supply only the following Items ( PROVISIONAL) of NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-100 here-in-above tyre copling rubber only N0.60

Welding Turning and machining works of Pump Shaft obtained from Item No 100 here-in-Before to true size to match with the new Parts / existing serviceable parts for proper allignment and smooth operation of Motor Pump Set complete all as specified and as directed

Servicing / over hauling of 3 Phase 415 Volts 1440 RPM 5 HP (Motor Make-Kirloskar, CG) Installed at Jalkendra a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantaling of induction Motor complete part by part carefully , testing all coils , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c)., Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed d). Reassembeling the motor complete with all existing serviceable parts obtained against Item 41 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of Motor to incorporate against each Item No-109 here-in-above DE ( Driver End ) bearing as per existing size suitable for Cap 5 HP Electric induction Motor Make- SKF/TATA no.6306ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of Motor to incorporate against each Item No-109 here-in-above NDE ( Non Driver End ) Bearing as per existing size suitable for Cap 5 HP Electric induction Motor Make- SKF/TATA no.6307ZZ ( heavy duty)

Supply only the following Items ( PROVISIONAL) of Motor to incorporate against each Item No-109 here-in-above Bakelite connection plate with brass nuts bolts and washers suitable for Motor cap 5 HP

Rewinding burnt coils of Induction Motor stator cap 5 HP obtained from Item Ser No-109 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete as directed

Servicing / over hauling of 3 Phase 415 Volts, 50 Hz , RPM 2900 Submersible Motor Pump set of capacity upto 30 HP( Make- Calama, Texmo, KSB,) installed installed inside borewell and jackwell at Jalkendra ,Lama Camp Rekhamari , AOP Pump House along with following others repairs. (a). Disconnecting delivery water connections Lifting column pipes along with connected submersible motor Pump set, submersible cable by making necessary arrangements from bore well ,setting aside and stacking column pipes for reuse complete all as directed by Engnr-in-Charge. (b) Dismantaling of Submersible Motor Pump- Set complete part by part carefully , testing all coils of submersible Motor , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. (c). Reassembeling the motor complete with all existing serviceable parts obtained against Item 44 (b), greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) (d). Painting the repaired motor and column Pipes externally with one coats of red oxide paint and two coat of synthetic enameal paint of shade as directed by Engnr-in-Charge. (e) Reinstall the Motor at its existing Position by Lowering column pipes and submersible Motot Pump set inside Bore well ,connecting Suction/ delivery Lines, all cable connections and testing on completion (NOTE: For Note description refer APPENDIX "A")

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above CI Suction Casing

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above CI Stage Bowl

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above M S Suction Strainer

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above SS Pump Shaft

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above Bronze Impeller

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above CI Valve Body

Supply only the following Items ( PROVISIONAL) of Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above Rubber Oil Seal

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above CI Adapator

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above Bronze Sand Guard

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above CI Thrust Bearing Housing

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above CI Bearing Body

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above Bronze Thrust bearing Plate

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above Bronze Thrust Bearing segments

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above CI Bearing segment carrier

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above Bronze bearing Bush

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above Rubber Diaphragm

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above Cr. St. Coupling Sleeve

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above MS heavy duty column Pipe 100mm Bore both ends flanged (3.0 Meter Long )

Supply only the following Items ( PROVISIONAL) of Submersible Motor upto capacity 20 HP to 30 HP to incorporate against each Item No-114 here-in-above MS heavy duty column Pipe 80mm Bore both ends flanged (3.0 Meter Long )

Rewinding stator of submersible motor of capacity 25/ 30 HP obtained from Item Ser No-114 here-in-above with water proof insulated copper wire of existing guage and size to achieve the specified / required RPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete all as specified and as directed.

Rewinding stator of submersible motor of capacity 20 /22.5 HP obtained from Item Ser No-44 here-in-above with water proof insulated copper wire of existing guage and size to achieve the specified / required RPM including taking out old unserviceable winding , cleaning/ repairing damaged slots , complete all as specified and as directed.

Material and labour for PVC insulated and sheathed flat 3 core, Size 4 Sqmm copper stranded conductor water proof submersible cable 1100 Volts Grade , and connecting to submersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed.

Material and labour for PVC insulated and sheathed flat 3 core, Size 6 Sqmm copper stranded conductor water proof submersible cable 1100 Volts Grade , and connecting to submersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed.

Material and labour for PVC insulated and sheathed flat 3 core, Size 10 Sqmm copper stranded conductor water proof submersible cable 1100 Volts Grade , and connecting to submersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed.

Material and labour for PVC insulated and sheathed flat 3 core, Size 16 Sqmm copper stranded conductor water proof submersible cable 1100 Volts Grade , and connecting to submersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed.

Supply, laying , fixing , passing through pipe or cable tray PVC insulated & PVC sheathed Multi core copper conductor 3 core 50 Sqmm 1100 Volts Grade cable confirming to IS 694 including including taking out old unserviceable cable connected from electric induction Motor to starter complete all as specified and as directed.

Supply, laying , fixing , passing through pipe or cable tray PVC insulated & PVC sheathed Multi core copper conductor 3 core 95 Sqmm 1100 Volts Grade cable confirming to IS 694 including including taking out old unserviceable cable connected from electric induction Motor to starter complete all as specified and as directed.

M & L Fully Automatic Star Delta starter suitable for 15 HP Motor In Sheet Metal Enclosure with single Phase Protection feature ( Motor Rating AC-3 Duty, 415 Volts, 50 Hz , 3 Phase complete with Timer, suitable cap relay including dismantling unserviceable starter , complete all as specified and as directed.

M & L Fully Automatic Star Delta starter suitable for 20 HP Motor In Sheet Metal Enclosure with single Phase Protection feature ( Motor Rating AC-3 Duty, 415 Volts, 50 Hz , 3 Phase complete with Timer, suitable cap relay including dismantling unserviceable starter , complete all as specified and as directed.

M & L Fully Automatic Star Delta starter suitable for 50 HP Motor In Sheet Metal Enclosure with single Phase Protection feature ( Motor Rating AC-3 Duty, 415 Volts, 50 Hz , 3 Phase complete with Timer, suitable cap relay including dismantling unserviceable starter , complete all as specified and as directed.

M & L Fully Automatic Star Delta starter suitable for 75 HP Motor In Sheet Metal Enclosure with single Phase Protection feature ( Motor Rating AC-3 Duty, 415 Volts, 50 Hz , 3 Phase complete with Timer, suitable cap relay including dismantling unserviceable starter , complete all as specified and as directed.

M & L Fully Automatic Star Delta starter suitable for 150 HP Motor In Sheet Metal Enclosure with single Phase Protection feature ( Motor Rating AC-3 Duty, 415 Volts, 50 Hz , 3 Phase complete with Timer, suitable cap relay including dismantling unserviceable starter , complete all as specified and as directed.

M & L Fully Automatic Star Delta starter suitable for 25 HP Submersible Motor Type MU-G In Sheet Metal Enclosure ( Motor Rating AC-3 Duty, 415 Volts, 50 Hz , 3 Phase complete including dismantling unserviceable starter , complete all as specified and as directed. Make- L & T or Equivalent

M & L Fully Automatic Star Delta starter suitable for 30 HP Submersible Motor Type MU-G In Sheet Metal Enclosure ( Motor Rating AC-3 Duty, 415 Volts, 50 Hz , 3 Phase complete including dismantling unserviceable starter , complete all as specified and as directed. Make- L & T or Equivalent

Supply and fixing 3 Pole Power contractor suitable for 150 HP Motor starter or as per existing including taking down existing unserviceable one complete all as specified and as directed.

Supply and fixing 3 Pole Power contractor suitable for 75 HP Motor starter or as per existing including taking down existing unserviceable one complete all as specified and as directed.

Supply and fixing 3 Pole Power contractor suitable for 40/50 HP Motor starter or as per existing including taking down existing unserviceable one complete all as specified and as directed.

Supply and fixing 3 Pole Power contractor suitable for 20 HP Motor starter or as per existing including taking down existing unserviceable one complete all as specified and as directed.

S & F as in repairs Electro Pneumatic Knob Type Time delay Relay ( Timer- 0.5 to 60 Sec ) suitable for 150 HP Motor Starter or as per existing size complete all as specified and as directed.

S & F as in repairs Thermal over load relay suitable for 75 HP Motor Starter or as per existing size complete all as specified and as directed.

S & F as in repairs Thermal over load relay suitable for 50/40 HP Motor Starter or as per existing size complete all as specified and as directed.

S & F as in repairs Thermal over load relay suitable for 20/25 HP Motor Starter or as per existing size complete all as specified and as directed.

S & F MCCB 4 Pole ,415 Volts , 63 Amps, with Thermal Magnetic release breaking capacity 25 kA fixing on existing LT Panel connecting and testing including taking out unserviceable one from panel , complete all as specified and as directed.

S & F MCCB 4 Pole ,415 Volts , 100/125 Amps, with Thermal Magnetic release breaking capacity 25 kA fixing on existing LT Panel connecting and testing including taking out unserviceable one from panel , complete all as specified and as directed.

S & F MCCB 4 Pole ,415 Volts , 160 Amps, with Thermal Magnetic release breaking capacity 25 kA fixing on existing LT Panel connecting and testing including taking out unserviceable one from panel , complete all as specified and as directed.

S & F MCCB 4 Pole ,415 Volts , 250 Amps, with Thermal Magnetic breaking capacity 36 kA fixing on existing LT Panel connecting and testing including taking out unserviceable one from panel , complete all as specified and as directed.

S & F MCCB 4 Pole ,415 Volts , 320/400 Amps, with Thermal Magnetic and Microprocessor release breaking capacity 36 kA fixing on existing LT Panel connecting and testing including taking out unserviceable one from panel , complete all as specified and as directed.

Scraping old paint of Electric induction Motor 150/125 HP Motor , NC Vertical/ Horizontall Split casing Pump , Suction , delivery Pipes, sluice valves , NRV Valves at Jalkendra , IMPH Pump House (Approx coverage area-10-15 Sqm) and Painting with one coats of red oxide paint and two coat of synthetic enameal paint of shade as directed by Engnr-in-Charge including writing Sm No. , MES No.complete as all specified and as directed

Scraping old paint of Electric induction Motor 75/50 HP Motor , NC Vertical/ Horizontall / Multi staging Pump , Suction , delivery Pipes, sluice valves , NRV Valves at Jalkendra , old Pump House, STP (Approx coverage area-10-12 Sqm) and Painting with one coats of red oxide paint and two coat of synthetic enameal paint of shade as directed by Engnr-in-Charge including writing Sm No. , MES No.complete as all specified and as directed

Scraping old paint of Electric induction Motor 20/15 HP Motor , NC Vertical/ Horizontall / Multi staging Pump , Suction , delivery Pipes, sluice valves , NRV Valves at Jalkendra ,Swimming Pool, Rekhamari, old Pump House, AROP Pump House (Approx coverage area-8-10 Sqm) and Painting with one coats of red oxide paint and two coat of synthetic enameal paint of shade as directed by Engnr-in-Charge including writing SM No. , MES No.complete as all specified and as directed

Scraping old paint of Electric induction Motor 10/7.5 HP Motor , NC Vertical/ Horizontal, Suction , delivery Pipes, sluice valves , NRV Valves (Approx coverage area-5-7 Sqm) and Painting with one coats of red oxide paint and two coat of synthetic enameal paint of shade as directed by Engnr-in-Charge including writing Sm No. , MES No.complete as all specified and as directed

S & F Cast Iron Foot valve of size 80mm to suction Pipe of Motor Pump set by disconnecting Lifting suction Pipe from shallow well/ UG Sump and fixing in Position after taking down existing unserviceable foot valve complete all as specified and as directed

S & F Cast Iron Foot valve of size 100 mm to suction Pipe of Motor Pump set by disconnecting Lifting suction Pipe from shallow well/ UG Sump and fixing in Position after taking down existing unserviceable foot valve complete all as specified and as directed

S & F Cast Iron Foot valve of size 150mm to suction Pipe of Motor Pump set by disconnecting Lifting suction Pipe from shallow well/ UG Sump and fixing in Position after taking down existing unserviceable foot valve complete all as specified and as directed

S & F Cast Iron Foot valve of size 200 mm to suction Pipe of Motor Pump set by disconnecting Lifting suction Pipe from shallow well/ UG Sump and fixing in Position after taking down existing unserviceable foot valve complete all as specified and as directed

S & F Cast Iron NRV of size 150 mm to suction Pipe of Motor Pump set by disconnecting Lifting suction Pipe from shallow well/ UG Sump and fixing in Position after taking down existing unserviceable foot valve complete all as specified and as directed

S & F Cast Iron NRV of size 200 mm to suction Pipe of Motor Pump set by disconnecting Lifting suction Pipe from shallow well/ UG Sump and fixing in Position after taking down existing unserviceable foot valve complete all as specified and as directed

S&F Cast Iron Diaphragm Valve of size 100 mm wheel type with necessary Nut, Bolts, Gasket, Washer, etc. including taking out old unserviceable one, complete all as specified and as directed.

S&F Cast Iron Diaphragm Valve of size 150 mm wheel type with necessary Nut, Bolts, Gasket, Washer, etc. including taking out old unserviceable one, complete all as specified and as directed.

Repair to water level indicator of OH Reservoir by replacement of brass float ball 300 mm dia 2mm thick mild steel pulley flexible steel wire rope from brass float ball to measuring key and painting to indicator with 2 coat of synthetic enamel paint and marking number with red/black reflective type colour complete and all as directed by Engr-in-charge.

Desliting / Taking out accumulated Silt, Sand , Mud etc.,from Jack well of diameter 6.10 Metre and 12.20 Metre deep ( installed at Jalkendra & old pump house) through Manhole , removing the same to a distance not exc. 50 Metre, complete all as specified and as directed. Note : The contractor to monitor day to day and avoid damage of VT pumpset due to intake of sand/mud (accumulated into bowl assembly . If any damage occured, the contractor is fully responsible for repaired the same without any extra payment.

Desliting / Taking out accumulated Silt, Sand ,Mud etc from Sand Trap of diameter 2.30 Metre and 3.00 Metre deep (installed at Jalkendra & Old Pump House) through Manhole, removing the same to a distance not exc. 50 Metre and depositing, complete all as specified and as directed.

Desliting / Taking out accumulated Silt, Sand ,Mud etc from Sand Catchment near River Bed Collection Chamber of Size 18.25 Metre x 4.57 Metre and 2.45 Metre deep , removing the same to a distance not exc. 50 Metre complete all as specified and as directed.

Desliting / Taking out accumulated sludge , Silt , Mud etc., from Flocculation Chamber, Flush mixing chamber , Clarifier Chamber , connected channels including scrapping down and cleaning internal surface of walls , Floors, Roofs, Mechanical Parts and cleaning blockage of wash out channels , pipes Drainage system etc. and removing the same to a distance not exc. 50 Metre complete all as specified and as directed.

Desliting / Taking out accumulated sludge , Silt , Mud etc., from Aeration Chamber installed at Jalkendra including scrapping down and cleaning internal surface of walls , Floors, Roofs, Mechanical Parts and cleaning blockage of wash out channels , pipes Drainage system etc. and removing the same to a distance not exc. 50 Metre and depositing complete all as specified and as directed. ,

Scrapping down , cleaning Internal Surfaces of Walls, Floors, Roofs, Drainage system etc of Under Ground Clear water sump ( installed at Jalkendra, IMPH ) of size 30.00x 30.00x 2.60 Metre including removing the accumulated sand/ silt from the chambers, depositing where directed at distance not exc. 50 Metre complete all as specified and as directed.

Scrapping down , cleaning Internal Surfaces of Walls, Floors, Roofs, Drainage system etc of Under Ground Clear water sump of size 15.00x 7.00x2.60 Metre ( installed at Old Pump House) including removing the accumulated sand/ silt from the chambers, depositing where directed at distance not exc. 50 Metre complete all as specified and as directed.

Scrapping down , cleaning Internal Surfaces of Walls, Floors, Roofs, Drainage system etc of Under Ground Clear water sump of size 9.25 x 5.60x 3.60 Metre ( installed at Air OP Pump House , Lama Camp, Rekharari Pump House ) including removing the accumulated sand/ silt from the Chambers, depositing where directed at distance not exc. 50 Metre complete all as specified and as directed.

Scrapping down , cleaning Internal Surfaces of Walls, Floors, Roofs, Drainage system etc of Raw Water Sedimentation Tank of Size 14.00 x 7.40 x 3.80 Metre ( installed at Old Pump House) including removing the accumulated sand/ silt from the chambers, depositing where directed at a distance not exc. 50 Metre complete all as specified and as directed.

Scrapping down , cleaning Internal Surfaces of Walls, Floors, Roofs, Drainage system etc of Raw Water Sedimentation Tank of Size 7.00 x 6.20 x 3.80 Metre ( installed at Lama Camp and Rekharari Pump House ) including removing the accumulated sand/ silt from the Chambers, depositing where directed at a distance not exc. 50 Metre complete all as specified and as directed.

Scrapping down, cleaning all Internal Surfaces of Walls, Floors, Roof, Incoming & Outgoing Pipe Lines , etc of RCC Over Head Reservoir (located at Pratap Nagar OH Reservoir) of size 17.00 Metre dia and 4.60 Metre deep outer Chamber and height of staging 16 Metre including removing accumulated sand/ silt from the Chambers, depositing where directed at a distance not exc.100 Metreincl draining out of entire water from OH reservoir by opening of wash out valve after blocking the delivery mains of each of the two compartments with gunny bags or other suitable arrangements and washing the same completly, after washing disnifecting the whole reservoir with solution of potasium permagnete and applying one coat of cement wash to inner sides of the both of the compartments and removing blockage of the delievery mains & marking the date of cleaning with paints on reservoirs complete all as specified and as directed.

Scrapping down, cleaning all Internal Surfaces of Walls, Floors, Roof, Incoming & Outgoing Pipe Lines , etc of RCC Over Head Reservoir (located at Shivaji Nagar, Govind Nagar and Tushar Charra ) of size 14.40 Metre dia and 3.95 Metre deep inner and 20.6 Metre dia and 3.5 Metre deep outer Chamber including removing the accumulated sand/ silt from the Chambers, depositing where directed at a distance not exc. .100 Metre incl draining out of entire water from OH reservoir by opening of wash out valve after blocking the delivery mains of each of the two compartments with gunny bags or other suitable arrangements and washing the same completly, after washing disnifecting the whole reservoir with solution of potasium permagnete and applying on ecoat of cement was to inner sides of the both of the compartments and removing blockage of the delievery mains & marking the date of cleaning with paints a=on reservoirs complete all as specified and as directed.

Scrapping down, cleaning all Internal Surfaces of Walls, Floors, Roof, Incoming & Outgoing Pipe Lines , etc of RCC Over Head Reservoir of capacity 50000 Gallons , 16.00 Metre staging height installed at AF Pump House , Army Avn Tech area , OMC Pump House and 180 MH including removing the accumulated sand / silt from the Chambers, depositing where directed at a distance not exc. 100 Metreincl draining out of entire water from OH reservoir by opening of wash out valve after blocking the delivery mains of each of the two compartments with gunny bags or other suitable arrangements and washing the same completly, after washing disnifecting the whole reservoir with solution of potasium permagnete and applying on ecoat of cement was to inner sides of the both of the compartments and removing blockage of the delievery mains & marking the date of cleaning with paints a=on reservoirs complete all as specified and as directed.

Scrapping down, cleaning all Internal Surfaces of Walls, Floors, Roof, Incoming & Outgoing Pipe Lines , etc of Prestressed Steel Tank Over Head Reservoir 9600 Gallons to 12000 Gallon capacity , 16.00 Metre staging height installed at Lama Camp , Rekharari Pump House. Old Pump House AF Pump House , including removing the accumulated sand / silt from the Chambers, depositing where directed at a distance not exc..100 Metreincl draining out of entire water from OH reservoir by opening of wash out valve after blocking the delivery mains of each of the two compartments with gunny bags or other suitable arrangements and washing the same completly, after washing disnifecting the whole reservoir with solution of potasium permagnete and applying on ecoat of cement was to inner sides of the both of the compartments and removing blockage of the delievery mains & marking the date of cleaning with paints a=on reservoirs complete all as specified and as directed.

Desliting / taking out accumulated Silt ,Mud etc from Temporary open channels of size 1.50 Metre wide and 1.50 Metre deep , connecting from main stream of River Gabhru to Sand Trap near Jack Well at Jalkendra including removing the accumulated sand / silt from the Chambers, depositing where directed at a distance not exc. 50 Metre complete all as specified and as directed.

M & L preparation of previously treated/ old painted internal surface of under ground sump, Raw water sumps 'Flocculation Chamber Flush Mixture and clarifier chamber and applying one coat of black bituminous paint suitable for drinking water, complete all as specified and as directed.

M & L for make channel/ route for flow/ bring water from each river to collection chamber/ Jackwell by using T & p/manpower regularly or alternate day or as requirement to maintain uninterupted supply of raw water to jackwell complted all as directed by Engr-in Charge

M & L for cutting / cleaning and removing of growing vegetation/ unwanted bushes in side installation area by using T & P or manpower when reqquired all as directed by Engr-in-Charge

M L for preparation to CI/DI MS rising, distribution, overflow, wash out and suction pipe line of any size in vertical/ horizondal position and painting two coat of super enameled black or sky blue paint over a coat of red oxcide duly marked inlet/outlet direction, overflow/ washout at various water supply installation/ OHT at any height/ staging under GE Missamari all as directed by Engr-in Charge. Note: The contractor to be quated the rate incl for making arrangement for stage/ ladder for painting work.

M & L for preparation of valve pit chamber cover for and angle iron of any size for two coat of super enemaled black paint over one coat of red oxcide all as directed.

M & L for preparation to sluice/release/NRV Valves of size 300/250 mm dia for two coat of super enemaled black paint over one coat of red oxcide all as directed.

Supply only grease for lubrication of moving parts of motors/pumpsets/chain pulleys etc

Supply only Copper lugs of size 6/10/16 sqmm for connection of starters at various water supply installations.

Supply only aluminium lugs of size 50/70/95/120/150/185/240/300 sqmm for connection of starters at various water supply installations.

Supply only PVC house pipe of size 80 mm for sludge/ dewatering pump at jalkendra water supply installation.

Supply and fabrication of MS chesis/ base frame of motor pump set 20 HP ( as per existing size and shape) including dismentaling of old existing installed at old pump house, lama camp, rekhamari,AROP and jalkendra pump house.

Supply and fabrication of MS chesis/ base frame of motor pump set 150 HP ( as per existing size and shape) including dismentaling of old existing installed at old pump house, lama camp, rekhamari,AROP and jalkendra pump house.

Supply only Brass bar/ block for making of brass bushing as per existing size for existing housing of various pump sets, induction motor and submersible pump complete all as specified and directed by EIC

Supply and fixing of brass Gate valve of size 50 mm complete all as specified and directed by EIC

Supply and fixing of brass Gate valve of size 25 mm complete all as specified and directed by EIC

Supply and fixing of brass Gate valve of size 20 mm complete all as specified and directed by EIC

Supply of JCB/Fork land for removal of silt in the open drain from Ghabharu River to sand catcher at Jalkendra all as specified and directed by EIC Note:- (a) No seprate payment for driver included in the quoted rate of item (b) No additional charges will be paid for the T&P required. (c) No additional charges will be paid for Fuel, coolant or fan belt, lubrication or other accessaries.

Sunrise Enterprise

M/S Manjit Singh