SPECIAL REPAIRS TO BATHROOMS DINING HALL AND GALLY OF VIKRAMADITYA INLIVING BARRACKS BUILDING NO P 323 P 323A AT SFNA NAVAL BASE KOCHI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for coloured Ceramic tile of size 600x600mm joint free with approved pattern and colour borders over cement screed 10 mm thick in CM 1:4 complete all as specified and directed.

M&L for pre polished Kota stone slab 20-25 mm thick with over cement screed in CM 1:4 not less than 15 mm thick complete all as specified and as directed by Engr - in Charge.

M&L for Glazed ceramic tiles coloured , as in vertical surfaces, size 450 x 350 x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set in 10mm thick cement screed bed in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed .

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for RCC M 30 design mix for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by the Engr -in-Charge.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed

M&L for Pre-cast cement concrete block masonry with solid blocks type C1, 1:3:6 (20 mm graded aggregate), exc. 10 cm in width and setting in 1:6 cement mortar, complete

Taking down cement plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M&L for cement plaster in two coat 8 mm thick in cement mortar 1:4 using WPC over 12mm thick back coat in CM 1:6 on external surfaces finished even & smooth without using extra cement all as directed. Note:-WPC shall be measured and paid seperately

Supply only integral water proofing compound.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6, smooth finished complete all as specified and as directed by Engr - in Charge.

M&L for rendering 5mm thick in CM 1:4 incl finishing even and smooth without using extra cement on ceiling/ chajja complete all as specified and as directed by Engr -in- Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc for rough finished surfaces complete all as specified

M&L for RCC M30 design mix for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajja and the like etc complete all as specified and as directed by Engr - in Charge

M&L for CRS/HCRM TMT bars 10mm dia and , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

Taking down Chowkats with shutters of area exc 1.5 Sqm but n.exc 4.00 Sqm each without taking off shutters from frame complete all as specified and as directed .

S&F second classhard woood plain solid,straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put togethr with glue pinned at joints complete all as specified and as directed

M&L for M.S Hold fasts of FI 25 x 3 mm all as specified

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in hold fast blocks complete all as specified and as directed

S&F for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed

S&F 35 mm thick IInd class hard wood factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with out mitred beads for securing glass etccomplete all as specified and as directed

S&F 35 mm thick Plain, framed, panelled shutters (any number of panels), IInd class hard wood with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats etc.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed

S&F Factory Made Solid PVC Moulded Door Shutter,with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

M&L for preparation of old wooden surfaces of any description and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr -in-Charge.

M&L for painting to new wooden surfaces of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and as directed

S&F extruded aluminium anodised handle 125 mm fabricated type polished and fixed with stainless steel screws complete all as specified and as directed

S&F MS helical door spring 300 mm long with roller and roller plate complete all as specified.

Supply and fix stainless steel butt hinges medium weight size 100mm size complete all as specified and as directed

M&L for 200 mm Aluminium anodised barrel tower bolts of extruded section rolled and fixed with stainless steel screws.all as specified

M&L for 100 mm Aluminium anodised barrel tower bolts of extruded section rolled and fixed with stainless steel screws.all as specified

M&L for preparation surface of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described and treated with tar or coal tar black paint complete

Taking out existing roof treatment alongwith screed, tarfelts,tiles etc, and removal of dismantled materials complete all as directed and as specified

M&L for 10 mm thick rendering in cement mortar 1:3 using WPC for roof treatment complete all as specified and directed by the Engr-in-Charge. Note : WPC shall be measured separately under relevant items.

M&L for water proofing treatment over RCC slab (i) Apply a coat of oil based bituminous primer @ 0.25 Kg / square metre on the prepared surface. (ii) Apply a coat of blown type bitumen grade 85/25 conforming to IS: 702 heated to a working temperature of 180 degree centigrade and applied @ 1.20 Kg /Sqm of the surface area. (iii)Provide and lay 4 mm thick APP modified torch applied water proofing membrane weighing not less than 4.0 Kg / Sqm reinforced with non-woven polyester matt weighing not less than 160 gm / Sqm having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 650 N/5 cm, tear strength of 180 N (min), a static puncture resistance of 180, keeping a minimum of 10 cm side over laps and 15 cm end lap. (iv)Apply a coat of blown type bitumen grade 85/25 conforming to IS: 702 heated to a working temperature of 180 degree centigrade and applied @ 1.20 Kg /Sqm of the surface area. (vii)Finishing surface with solar reflective bituminous aluminium paint @ 0.10 Kg / Sqm.

Demolition of cement concrete (un reinforced) in any position n. exc 15cm thickness complete all as specified

M&L for 75 mm thick PCC Type C2 (1:3:6) using 40 mm graded aggregate as in plinth protection finished even and fair with out using extra cement all as specified.

M&L Glass dividing strips, 3 mm thick 22 mm width of strip complete all as specified and as directed.

S&F in repairs for Vitreous China wash down water closet pan (pedestal pattern), white with Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed . Make : Hindware/Cera

S&F in repair Vitreous China Urinal, Size 375x390x590mm, white all as specified excluding flushing pipe and waste pipe complete all as specified.Make: CERA cat part No. S 4020112 or equivalent make mentioned in list of manufactures.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurryand pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over 15mm tk CM 1:4 complete all as specified and as directed

S&F in repair Vitreous China counter wash basin, white, oval shape, size 560x470x190mm , including cutting for and pinning in ends of brackets and brackets complete all as specified and as directed.Make: CERA cat part No. S 2030103 or equivalent make mentioned in list of manufactures.

S&F 32 mm waste coupling of PTMT (half or full threaded) (Minimum weight 32 mm-45 gms/ 40mm-60 gms) all as specified and as directed

S&F in rep 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed

S&F in repairs 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets.Make : Hindware/Cera

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints 50mm dia as in waste pipe for WHB all as specified and as directed .

Demolition and breaking up drain pipes 100mm (salt glazed ware, AC, PVC or reinforced concrete) any dia set in cement mortar height upto 12 mtr complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall in repair height upto 12 mtr complete all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall in repair height upto 12 mtr complete all as specified..

S&F 75mm bore PVC (SWR) bend.

S&F 110mm bore PVC (SWR) bend.

S&F 75 mm PVC (SWR) branch piece, single (single Y) equal or un equal

S&F 110 mm PVC (SWR) branch piece, single (single Y) equal or un equal

S&F PVC SWR floor trap plain 75mm dia with grating including jointing with solvent cement in repairs complete all as specified and directed.

S&F PVC Gully trap 125mm setting and jointing with solvent cement in repairs complete all as specified and directed.

Complete removal of existing surface finishes of external wall, preparation of surface and applying coat of weather proof primer for weather proof paint complete all as specified and as directed . Note:- Application of paint and primer shall be as per manufacturer's instruction.

M&L for application of first coat of weather proof paint (anti fungal paint) ( Asian paint apex ultima protek or equivalent of Berger /Nerolac )on primed wall surface using spray application or mechanical means, to get a smooth and tint free surface and allowed to dry for at least 8 hrs/ overnight to receive second coat of acrylic exterior emulsion paint complete all as specified and as directed.

M&L for application of second coat of weather proof paint (anti fungal paint) ( Asian paint apex ultima protek or equivalent of Berger /Nerolac ) over first coat on wall surface using spray application or mechanical means, to get a smooth and tint free surface complete all as specified and as directed. Note for item No. 62 to 64 (i) The old surface shall prepared using mechanical ways I.e., jet-spray, grinding etc., in such a manner that there should not be any impression of dent, all cracks to be filled with crack filler, water proofing primer in shaft/dampness areas and it should be made even all as per manufacturers instruction before application of putty base primer/base coat and emulsion paint. (ii). The work shall be got executed through authorised applicator of approved manufacturer. Authorisation letter of applicator shall be produced by the contractor before starting the work (iii) The contractor shall submit performance Guarantee certificate provided by manufacturer for a period of FIVE years from the certified date of completion of entire work. (iv) After preparation of surface exterior putty to be applied to make surface even to receive base coat and two coat of emulsion paint, the same shall be got approved by GE before each stage

M&L for complete removal of existing surfaces and applying two coats of oil bound distemper over a coat of primer over 1.5mm thick wall putty complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of primer over 1.5mm thick internal wall putty complete all as specified and directed.

M&L for preparation of new surfaces of ceiling surfaces and applying three coat of white wash complete all as specified and directed.

M&L for preparation of old surfaces of ceiling by brooming down or by steel wire brushing and applying two coat of white wash complete all as specified and directed.

Taking down Chowkhats or frames not exc. 1.5 sq. m each but with shutters (without taking off shutters from the frame).

S&F powder coated aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F aluminium powder coated dark coloured deco grill 75 mm aperture, made out of 7.5 mm plate and finished decogrillfe will have 7.5 mm width and 6 mm thick with rubber beading & looks etc complete all as specified and directed.

S&F for powder coated Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified

S & F for 12 mm thick both sides prelaminated Particle board, exterior grade, fixed with screws to frame work in table top, cup board shutters, partitions, shelves etc. complete all as specified and diercted.

S & F 5.5 mm thick sheet glass ordinary quality and glazing with oil putty square n.exc 5 sqm in each pane complete all as specified and directed.

S&F solar suncontrol film 25 micron refelective type exc 1.5sqm complete all as specified and directed.

S&F Door closer cast iron body hydraulically regulated,designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp insulation etc.) or insulation boards / slabs / blankets, any thickness including fillet complete all as specified and directed.

M&L for 5mm thick printed PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified.

M&L 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

Dismantling of single layer Mangalore pattern tiles with roof tiles or slate roofing complete complete all as specified and directed.

S & F Mangalore pattern tile roofing, laid dry complete all as specified and directed.

S & F ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement moratr 1:6 complete all as specified and directed.

S&F powder coated aluminum (Minimum thickness of powder coating 50 micron) sliding window and ventilator frame double shutter (Glass and wire mesh) without sash bar, including all necessary jointing cleats, hold fasts, rubber gasket, anodised snap beading, anodised aluminium fitting such as aluminium fitting such as 'F' channel if required for wire mesh or aluminium grill, aluminium handle, locking arrangement etc based on Hindalco catalogue No: 1. 4087 - 92.36x29.70x1.20mm = 3 Track Bottom. 2. 4099 - 92.36x29.70x1.20mm = 3 Track Side & Top . 2. 9395 - 39.00x20.00x1.10mm = Shuter Vertical 3. 3994 - 41.00x20.00x1.20 = Shutter Top & Botam. 4. 9779 - 39.00x20.00x1.16mm = Shutter Vertical Inter Lock, including 4mm thick glass and wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as directed by the Enginner-in-charge.

S&F powder coated aluminum (Minimum thickness of powder coating 50 micron) sliding window and ventilator frame without sash bar, including all necessary jointing cleats hold fasts rubber gasket, anodised snap beading, anodized aluminium fittings such as "F" channel if required for wire mesh or aluminium grill, aluminum handle locking arrangement etc based on Hindalco catelogue No. 1. 4095 - 61.98x29.70x1.60mm = 2 track 2. 9777- 39.00x20.00x1.60mm = Shutter vertical 3. 3994 - 41.00x20.00x1.20mm = shutter top and bottom 4. 9778 - 39.00x20.00x1.50mm = Shutter vertical inter lock, including 4mm thick glass complete all as specified and as directed

S&F of Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed.

M&L for Providing precast cement concrete solid building blocks Type C1, 1:3:6 (20mm graded aggregate) or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar, complete, in walls set in Cement mortar 1:4 complete all as specified and as directed.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

M&L for RCC design mix M 30 for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by the Engr -in-Charge.

M&L for Cement concrete 25mm thick type B-0, 1:2:4 (12.5mm graded aggregate) as in leveling course over PCC/ RCC slab complete all as specified and as directed by the Engr -in-Charge.

Excavating in trenches, n exc1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out soft/loose soil all as specified and as directed

Returning, filling in, includingspreading, levelling, watering and well ramming in layers not exc 25 cm all as specified and as directed

Removing excavated material n exc. 50m and depositing wheredirected at a level n exc. 1.5 m above the starting point all as specified and as directed

M&L Reinforced concrete pipes 150mm dia , class NP2, laid and jointed complete with collars all as specified and as directed

M&L for Plain Concrete type C2, 1:3:6 in concrete bed to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in all as specified and directed.

M&L Providing precast cement concrete in cover slabs (for man holes etc) Type B1 1:2:4 using 20mm graded aggregate set in CM 1:6 (Reinforcement shall be measured and paid seperately)

M&L Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar 1:6, Type C1 1:3:6 (20mm graded aggregate) complete all as specified and as directed.

S&F RCC Hume pipe septic tank for 100 users designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc complete all as specified and directed.

S&F Soakage pit of size 2.70mtr amd 2.4 mtr depth complete all as shown on drg No.TD/A/16, sheet No.1/1.complete all as specified and directed.

M&L PCC 1:2:4 type B2 (20mm graded aggregate) for haunching inside the manhole

M&L for CRS/HCRM TMT bars 5mm to 10mm dia as in stirrups cut to length, bent to shape required including bending spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia and securing with clips complete all as specified.

S&F of 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each Pane complete all as specified and as directed by the Engr –in-Charge.

S&F of 4mm thick Sheet glass, ordinary quality ground or obscured or frosted, on one side and glazing with oil putty in square n exc 0.5 sq. m in each Pane complete all as specified and as directed by the Engr –in-Charge

S&F in repair for Vitreous china urinal partition white , Size 90x320x720mm, “Cera Cat No. S4090101”, of size 310x700 mm, complete all as specified and as directed by Engr-in-Charge

M&L for Vitrified ceramic tiles, light shade, 10 mm thick (Square / Rectangular), polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, along with dark color border tile of 100/150mm wide, laid in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match, including 15 mm thick Screed bed or bedding layer in Cement Mortar 1: 4, complete all as specified and as directed by Engineer in Charge.

Use and waste of form work to to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat fair finished surfaces complete all as specified

M&L chipping off the disintegrated concrete of sunken slabs/RCC slab and sides and clean the area with wire brush and coir brush. Seal the disturbed area with polymer modified mortar using of approved make. Coving has to be done at all the corners with polymer modified mortar Seal all the plumbing line sand holes with non shrink grout of make BASF/ M/S Fosroc, IWL, STP Ltd. Replace all pipes by PVC and shall be placed properly in position Keep the water on sunken tanks and floors for 24 hrs for observing the leakages and to ensure water tightness. Pressure grouting has to be done at all the damaged areas/ joints with water proofing admixture .Water proof the area with Acrylic polymer modified water proofing coating , Brush bond RFX or equivalent in two coats. Water proofing products confirm to BASF/ M/S Fosroc chemicals pvt ltd/ IWL, STP Ltd.

M&L for 100 mm thick Plain Cement Concrete 1:4:8, Type D-2, (40 mm graded stone aggregate) as in sub base to floor, complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and as directed by Engr -in-Charge.

Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessary fittings, solvents of size 40 mm dia including taking down old one complete all as specified and directed. Make Supreme/ Eurotech/ Astral/ SFMC

All as per item No. 112 here-in-before but of size 25 mm dia

All as per item No. 112 here-in-before but of size 20 mm dia

S&F CPVC Ball Valve of size 40 mm dia suitable for CPVC pipe incl necessary fittings and taking down old one complete all as specified and directed. Make : Supreme/ Eurotech/ Astral/ SFMC

All as per item No. 115 here-in-before but of size 25 mm dia

All as per item No.115 here-in-before but of size 20 mm dia

Supply and fixing of Bib tap CP, Quarter turn with flange and areator, fancy type Long body cast copper alloy with crutch or butterfly handle screwed for GI/cpvc pipe of size 15mm , complete all as specified and as directed by the Engineer-in-charge.(Make : Model No F2004152 of Cera or equivalent make from list of manufactures.

Supply and fixing 15mm angle valve,quater turn with flange, with flange type chromium plated for fixing with CPVC pipe and taking down old one complete specified and as directed by the Engineer-in-charge.(Make : Model No: F2004201 of Cera or equivalent make from list of manufactures.

Supply and fixing of swivel overhead shower of PTMT any colour with shower arm 15 mm size, 195 mm long with bend of 45 degree with flange for fixing with CPVC pipe and takong down old one, complete and all as specified and as directed by the Engineer -in-Charge. Cat Part No. F 7020104 of Cera or equivalent make from list of manufactures.

Supply and fix concealed stop cock regular body,Quarter turn with adjustable wall flange chromium plated with CP cup fancy type of size 20mm and taking down old unserviceble one, complete all as specified and as directedby the Engineer-in-charge.(Make : Model NO: F2002362 of Cera or equivalent make from list of manufactures.

Supply and fixing health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe ,all as per specified and directed (Make : Model No: F8030102 of Cera or equivalent make from list of manufactures.

Supply and fixing of CP Bib cock short body with flange and nozzle for garden/ washing machine of size 15 mm including necessary fixing accessories with GI/ CPVC pipes and taking down old unserviceable tap of any make complete all as specified and as directed by the Engineer-in-Charge. (Make : Cera Model No. F 2003153 or equivalent make from list of manufactures.

Supply and fixing CP angle cock, self closers/ pressmatic with wall flange for urinal pots to fixed in 20/15mm pipe, complete all as specified and directed by the Engineer-in-Charge. (Model No. F 9020203 of Cera or equivalent make from list of manufactures.

Supply and fixing PVC connection pipe 16mm dia (outer 450mm long cold water and complete with brass union on both sides to suit 15mm GI pipe complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in of Rotational mouldede polyethylene water storage tanks (cylinderical vertical with closed top) hoisted & fixed in position of capacity 500 liters Make : Sintex (ISI)/ Aquatech

S/F float valve synthetic(PVC) of size 25 mm dia high pressure with polythene ball of size 6" dia and flynut complete all as specified and directed.

Supply and fixing in pillar taps, swan neck spout with aerator, cast copper alloy with capstan heads chromium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed for 15mm bore pipe, complete all as specified and directed by the Engineer-in-charge. Model No: F2008104 of Cera or any other make of approved manufacturer’s list.

Material and Labour for cutting chasses on walls floor etc not exceeding 20 cm girth and making good the disturbed surface to match with the existing after removing the existing concealed pipe/laying new pipe, complete all as specified and directed by the Engineer-in-charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting sheet metal encl. with plug & socket etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L , point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits) with 1.5 sqmm nominal cross sectional area, copper conductor unsheathed FRLS cable 1100 Volts grade ISI-694 marked with valid CML No. single core multistranded cable in and including medium grade concealed PVC conduit not less than 20mm dia and accessories ISI marked with valid CML No (IS-9573-1983 for conduits and IS: 3419: 1976 for conduit accessories) and including 1.6 mm thick MS sheet/ pressed steel sunken boxes depth not less than 50mm (earth dolly) duly painted with two coats of anti corrosive paint / aluminium paint over a coat of red oxide primer internally and two coats of black bituminous paints over a coat of red oxide primer externally covered with 3 mm thick plastic laminated sheet cover for fixing of switches sockets and fan regulators etc. including 1.5 Sqmm nominal cross sectional area PVC insulated copper conductor unsheathed FRLS cable single core multistranded cable as earth continuity wire all as specified and as directed for the following:- (a) One light point controlled by one switch complete all as specifeid and as directed.

All as per item No. 131 above but for One fan point / exhaust fan point controlled by one switch & regulator complete all as specifeid and as directed.

All as per item No. 131 above but for One 5 pin 5 Amps Socket point controlled by one switch on same board complete all as specifeid and as directed.

All as per item No. 131 above but for One 5 pin 5 Amps socket point controlled by one switch on independent board complete all as specifeid and as directed.

All as per item No 131 above but with 2.5 Sqmm copper conductor including 2.5 Sqmm copper cable as earth wire for one 6 Pin 16 Amps Socket outlet on independent board complete all as specifeid and as directed.

Taking down existing tube light fitting, complete 1 x 20 W/ 2 x 20 W and keep aside for re-using or removing complete all as specified and directed.

Taking down existing round type/ square type ceiling lights of any type & size and keeping aside or removing complete all as specified and directed.

Taking down existing MCCB of 200 Amps of any type and make & removing complete all as specified and directed..

Taking down existing MCB TPN DB of any type and make along with isolators MCB SPN, MCBs etc and removing complete all as specified and directed.

Taking down existing MCB DB SPN of 8 ways along with MCBs & MCB SPN & removing complete all as specified and directed.

S&F switch piano flush type 5A one way complete all as specifeid and as directed.

S & F Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body complete all as specifeid and as directed.

S&F Socket 5 pin 5 Amps flush type complete all as specifeid and as directed.

S & F socket outlet 2 in 1, 3 pin, 5 and 15 Amps flush type universal complete all as specifeid and as directed.

S&F Switch piano flush type single pole 1 way, 15 Amps complete all as specifeid and as directed.

S&F step type fan regulator electronic flush type 120Watt 5 step complete all as specified and directed.

Supply & fix Regal Batten for LED tube lights, both side connection type and LED tube rod 1 x 20 Watt, 120 Lumen/Watt both side connection & electronic driver,designed for glare free symmetrical light distribution all as specified and as directed. Make of batten : Havells Cat Part No. Regal batten 8UPT001X22WSSBSWH / Crompton Cat Part No. IGP131LT8-16 / Philips Cat Part No. TMC501P1XTLED22WP3241 Make of tube rod : Havells Cat Part No. Crystal 1213T8DSTL20W LED 865 GLASS / Crompton Cat Part No. LG-T8-20-865-2 / Philips Cat Part No. Essential LED tube 1200mm 20W865T865T81ND-1

S&F tube light fitting 2 X 22 with T8 LED tube of 20 Watt with aluminium Extrusion heat sink for optimum performance with 120 Lumen/watt and batten pre wired suitable to use with LED tube with concealed accessaries complete Make : Havells model No REGALBATTENT8UPTO2X22WDSBSWH and CRYSTAL1213T8DSTL20WLED865SGLASS (2 Nos) / Crompton Cat Part No. IGP162LT8-16 and Tube rod LT8-20-865

Fixing only existing tubelight fitting any type and size with existing tube rod whereas directed all as specified. Note : Tube light fittings with tube rods obtained as per item No. 127 to be used for varanda/bathroom

Supply and fixing LED Mini mirror light 1 x 10W Watt Wall/Surface mounted luminaries with engineering plastic housing 75 Lumen/watt, wired with all accessories complete incl provn of flexible copper wire from ceiling rose to light fitting terminal. Make- Make :Crompton Cat No. LDL-10-WW, Luker Cat Part No. LTSM10, Philips B No 21LED12S

Taking down existing ceiling fans of 1200 mm sweep complete and removing to workshop for following repairs & re-fixing at any location all as directed. (a) Strip opening/ cutting of the ceiling fan and rewinding with super enamelled copper winding wire of same capacity, heating, baking, sleeves, varnish etc. (b) Replacement of ball bearings of suitable size. (c) Replacement of fan capacitor 2.5 m.f.d (d) Re-assembling and painting to the fans by spray painting with super finish including blades and re-fixing at directed location.

All as per item No. 151 above but for exhaust fans of 300/380 mm sweep including necessary welding to the brackets, frame etc as per site requirement all as directed.

Taking down existing ceiling fan and Painting of celing fans complete including down rods, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and hanging in original position and connecting up including provision of cable from ceiling rose or connector to fan all as directed.

Taking down existing exhaust fan and Painting of exhaust fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and fixing in original position and connecting up including provision of cable from ceiling rose or connector to fan all as directed.

S&F Sheet metal enclosures with socket plug top and MCB' single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 A MCB. Make Havells, Cat Part No. DHDMCSN 0251020/ L&T Cat Part No. DBMPS120SD/ Schneider Cat Part No. A9HMS220

S&F Sheet metal enclosure MCB TPN DB 8 way double door IP 43 type suitable for 200 amp including all electrical connection all as specified and as directed. Make: Schneider Cat Part No. A9HVTD08 / Legrand series XLᶟ6300 enclosure / L&T Cat Part No. DBPSG008DD

S&F Sheet metal enclosure MCB TPN DB 12 way double door IP 43 type suitable for 200 amp including all electrical connection all as specified and as directed. Make: Schneider Cat Part No. A9HVTD12 / Legrand series XLᶟ6300 enclosure / L&T Cat Part No. DBPSG012DD

S&F Sheet metal enclosure MCB SPN DB 8 way double door (metal door) IP 43 type suitable for 200 amp\ including all electrical connection all as specified and as directed. Make : Schneider Cat Part No. A9HSNS08 / L&T Cat Part No. DBSPN008SD / Legrand Cat Part No. XLᶟ400

S&F MCCB 4 pole 160 Amp 415V adjustable type with breaking capacity 36 KA with suitable size enclosure all as specified and directed. Make : L&T Cat Part No. CM90642OOPO/ Legrand Cat Part No.of DPXᶟ Series - 420259/ Schneider Cat Part No. LV431630.

S&F MCB 'B' Curve 63 Amp Four pole, 415 Volts 10 KA, all as specified and directed. Make Schneider Cat Part No. A9N4P63B.

S&F MCB 'B' Curve 40 Amp SPN ,240 Volts 10 KA all as specified and directed. Make Schneider Cat Part No. A9N2P40B.

S&F MCB 'B' Curve SP 6 To 32 Amp , 240 Volts, 10KA all as specified and directed. Make : Schneider Cat Part No. A9N1P06B-32B / L&T Cat Part No. BB10320B / Legrand Cat Part No. 408587-408596

S&F RCCB 63 Amp For earthing leakage protection four pole 30 mA, 10 KA all as specified. Make Schneider Cat Part No. A9N16208/ Legrand Cat Part No. 411369/ L&T Cat Part No. BG406303”

Taking down old sub main wiring of any type and size and removing , making good disturbed wall surfaces matching with existing surfaces all as specified and directed.

M/L submain wiring with 2 single core 4 Sqmm PVC insulated unsheathed multistranded copper conductor cable 1100 volt grade drawn throgh and including PVC rigid conduit concealed wiring inculding necessary PVC conduit specials including chases cutting complete exceapt beam and RCC roof and one run of 4Sqmm PVC insulated unshearthed single core 1100 volts grade multistranded copper conductor cable as earth continuity conduto9r and connceting with suitable size thimble complete allas specified and as directed. Note: two run of 4 sqmm size PVC cable , one run of 4 Sqmm size PVC cable as earth wire and one run of PVC conduit shall be measured as one unit length

All as per item No 165 above but with 2 single core 6 Sqmm PVC insulated copper conductor with 1 run 6 Sqmm copper conductor as earth wire complete all as specified and directed.

All as per item No 165 above but with 4 single core 10 Sqmm PVC insulated copper conductor with 1 run 10 Sqmm copper conductor as earth wire complete all as specified and directed.

All as per item No 165 above but with 4 single core 16 Sqmm PVC insulated copper conductor with 1 run 10 Sqmm copper conductor as earth wire complete all as specified and directed.

M&L in repair earthing complete with galvanised steel earth plate electrode 60 cm x 60cm x6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meters below normal ground level, connected to GI earth lead wire 4mm dia upto length 7.5 mtr by means of bolts, nuts and washers of galvanised steel all as shown in electrical plate No. 3 connected to earthing test point complete all as specified and indicated including testing on completion including taking out old earthing complete. Note : The rate is deemed to be inclusive of the cost of complete earth work in any type of soil. PCC 1:3:6 type C-1 for chamber,RCC 1:2:4 type B1 for cover slab 50 mm thick, reinforcement 8 mm CTD bars @ 100 mm c/c both way, necessary form work, handle, charcoal dust 20mm dia GI med grade for watering and 40mm dia GI med grade earth lead protection pipes with funnel and wire mesh all complete all as specified and directed.

M.J.JOY AND COMPANY

Albert Rebello and Company