PROVN OF 01 X TECH STORE SHELTER AT TECH AREA OF ARMY AVN SQN (LCH) AND PROVN OF CERTAIN MINOR WORKS UNDER GE MISSAMARI

Amount

Surface dressing in soft loose soil n exc 15 cm deep and getting out, complete all as directed.

Excavation in trenches n.exc. 1.5 m width and n.exc. 1.5 m in depth for foundation in soft/loose soil & getting out, complete all as directed.

Excavation in trenches exc. 1.5 m width and not exc. 3.00 m in depth for foundation in mud soil & getting out as in foundation including necessary dewatering as required, complete all as directed.

Returning filling in, including spreading, levelling, watering & well ramming in layers not exc 25 cm, complete all as specified and directed.

Removing excavated material (soil) n exc 50 m & depositing where directed at a level n exc 1.5 m, complete all as directed.

M&L cement concrete with PCC type D2 1:4:8 using 40mm graded aggregate as in foundation, complete all as specified and directed.

M&L for RCC design mix M25 using 20 mm graded aggrgate for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass co, complete all as specified and directed.

M&L for RCC design mix M25 using 20 mm graded aggregate for columns, pillars,posts and struts, complete all as specified and directed.

M&L for RCC design mix M25 using 20 mm graded aggregate for beams, cantilevers, roof beam , lintels over 1.5 m span, etc, complete all as specified and directed.

M&L for RCC design mix M25 using 20 mm graded aggregate for Slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC design mix M25 using 20 mm graded aggregate for chajjas complete all as specified and directed.

M&L for Precast reinforced design mix M25 concrete cover slab (using 20mm graded aggregate) as in drain cover, manhole cover, etc, set in cement mortar 1:6 complete all as specified and directed.

M & L for TMT reinforcement 10 mm dia and over cut to length bent to shape including cranking, banding spirally for hooping columns, hooking end and binding with and including mild steel wire not less than 0.90 mm dia (annealed) complete all as specified and directed .

S & F mild steel TMT bar 5 mm dia and over upto and including 10mm dia in strrups as in including cutting, bending and binding with and including mild steel not less than 0.9 mm dia (annealed) complete all as specified and directed .

M&L Form work for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, flat, rought finished surfaces of concerete complete all as specified and directed.

M & L Form work for sides of pillars, posts, columns & similar works, square rectangular or polygonal flat, rought finished surfaces of concerete complete all as specified and directed.

M & L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc flat, rought finished surfaces of concerete complete all as specified and directed.

M & L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat, rought finished surfaces of concerete complete all as specified and directed. complete all as specified and directed.

M&L for brick work with burnt old size bricks built in cement mortar 1:6 straight or curved on plan exceeding 6mtr mean radius and all as directed.

M&L for 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) mixed with WPC as per manufactures instruction with a coat of hot blown bitumen of Grade VG-10 @ 1.5 Kg/Sqm and blended with clean dry sand @ 0.05Cum/Sqm complete all as specified and directed. Note:- WPC shall be measured & paid separately

M&L rendering 15mm thick on other than fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and smooth (without using extra cement), complete all as specified and directed..

M&L rendering 15mm thick on fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and fair without using extra cement, complete all as specified and directed.

M&L for rendering 20mm thick with cement mortar 1:4 on fair faces of brick work in two layers (10mm and 10mm) sperately mixed with water proofing compund in top layer as per manufacturers instruction and finishing the surfaces even and fair complete all as specified and directed. Note:- WPC shall be measured & paid separately

Supply only integral Water proofing compund, complete all as specified and directed.

M&L for rendering 5 mm thick on ceiling or concrete Surfaces in cement mortar 1:3 finished even and smooth. (without using extra cement), complete all as specified and directed.

M&L 75mm thick cement concrete (1:3:6) type C-2( using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed.

M&L Sand filling under floors or in foundations including watering and conosoldiation complete all as specified and directed.

M&L Hardcore of gauge n exc. 63 mm, Broken stone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface,complete all as specified and directed.

M&L for 100mm thick cement concrete type D-2 (1:4:8) using 40 mm graded stone aggregate as in sub base complete all as specified and directed..

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sandcomplete all as specified and as directed.

M&L Virified Ceramic tiles dark shade, double charged 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqms as in vertical surfaces/dadoo,set and jointed in neat cement slurry & pointed in white or colour cement to match including backing coat 10 mm thick in Cement Mortar 1:4,complete all as specified and directed.

M&L Virified Ceramic tiles dark shade, double charged 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick Screed bed or bedding layer of cement mortar 1:6, for laying floor finishes,complete all as specified and directed.

S & F Second class hard wood kiln seasoned and chemically pressure treated plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete all as specified and directed.

S & F 35 mm thick factory made Second class hard wood kiln seasoned and chemically pressure treated Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc,complete all as specified and directed.

Supply for anodised aluminium three track sliding window and ventilator frame side/top/shutters (weight of section not less that 0.55 Kg/RM) aluminium section without sash bar aluminium section including all necessary joining cleats,hold fast, rubber gasket anodised snap beading, anodised aluminium fittings, suitable alum handle and locking arrangement etc, two track for glass and one track for aluminium wire mess etc, including powder coated of any colour (thick of power coating not less than 50 micron) & providing AC hole complete all as specified and directed.. Note:- (i) Wire cloth /glass shall be measured and paid separately at SUPPLY only rates under appropiate items. (ii) Labour charges for fixing of wire cloth/glass panes is demeed to be included in unit the unit rate quoted.

Supply only 4 mm thick Sheet glass, ordinary quality and glazing with aluminium beads in squares exceeding 0.50 Sqm in each pane, complete all as specified and directed.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium stapple complete all as specified and directed.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or revited, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confirming to Fe.290. Gde-E-165, including necessary prepration of surface and applying a coat of red oxide zinc chrome primercomplete all as specified and directed.

S&F mild steel hold fasts; for securing chowkhats and similar small articles conforming to Fe-290 Gde-E-165 incuding treating hold fast with tar or coal tar black paint, sanding complete all as specified and as directed.

M&L providing plain cement concrete type C-1, (1:3:6), (using 20 mm graded stone aggregate), as in fixing of hold fast including necessary form work as required complete all as specified and directed.

M&L preparing surface of wood and wood based materials, and new or old of any description and girth,not otherwise described and treated with applying two coats of creosote oil,complete all as specified and as directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed.

S&F aluminium alloy 250mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy and fixed, complete all as specified and directed.

S&F 100mm MS butt hinges medium weight, complete all as specified and directed.

S&F 150mm aluminium handle cast type anodised, complete all as specified and directed.

M&L prepraton of new ceiling surfaces and applying three coat of white wash complete all as specified and directed.

M&L for applying a coat of 1mm thick wall care putty over plaster surface to prepare the surface even and smooth as per manufacture instruction, complete all as specified and as directed.

M&L for preparation of new plastered wall surface applying two coat of oil bound distemper over a coat of primer complete all as specified and directed.

M & L for preparation of new wall surface applying Two or more coats of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @2.20 litre/ 10 sqm over new surface over 1 mm thick wall care putty,complete all as specified and directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following course of treatment/specification from bottom to top complete all as specified and directed:- (i) Rendering 10mm thick in CM (1:4) mixed with and including water proofing compound as per manufacture instruction on existing roof surface true to level after applying cement slurry @ 3Kg/Sqm over RCC slab when concrete is green ii) Applying one coat of bituminous primer @ 0.40 Ltr/Sqm. (iii) Supply and laying 3mm thick APP based olymeric membrane of approved manufacturer with weight not less than 3.50 Kgs per Sqm, reinforced with non-woven polyester febric weight not less than 160gms per Sqm. Polymeric membrane shall be taken to a height of 30cm(minimum) and than inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (iv) One coat of Solar reflective bituminious Aluminium paint of approved brand to be provided over the APP membrane as per manufacturers instructions. Note : (a) Work shall be carried out through specialized applicator approvrd by GE. Contractor shall submit sufficent documents/Credentials in support of Applicator whom he wants the work excuted. (b) Laying APP based polymeric membrane shall be done torch on method as per manufactures instructions. (c) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instruction

M&L Preparation of new or previously untreated wood surfaces of any description, over 10 cm width or girth, not otherwise described appling applying two coat of synthetic enamel paint over one coat of pink primer,complete all as specified and directed..

M&L preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 including necessary preperation of surfaces and applying one shop coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F Prepainted galvalume aluminium zink coating GI based corrugated/semi corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed..

M&L Pre-cast cement concrete block masonry, type C1 1:3:6 using 20mm graded aggregate with solid blocks, exc. 10cm in width and setting in mortar 1:4, complete complete all as specified and directed.

M&L for 100mm thick cement concrete type B-2 (1:2:4) using 40 mm graded stone aggregate as foundation, mass conctete etc complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&LTreating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&LTreating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for concealed point wiring with two single core 1.5 Sq.mm size FRLSH multistranded copper conductor PVC insulated cables and one single core 1.5 Sq.mm size green FRLSH colour PVC insulated,multistranded copper conductor PVC cable as earth continuity conductor,1100 volts grade, complete drawn in and including 20mm(minimim) medium grade rigid PVC CONDUIT and conduit accessories i.e. joint boxes, terminal boxes for mounting or housing switches, socket outlets, fan regulators, etc. confirming to IS specifications, including Mild Steel Pressed Terminal Box 1.22mm thick of suitable size duly painted with red oxide metal primer with 3.0mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, etc. with including cutting chases for conduits & sinkings for MS Sunken boxes & making good to walls, floors etc. complete all as specified & as directed for the following :-

All as per item No 62 herein before but light point controlled by one, one way switch 5 Amps

All as per item No 62 herein before but One 3 point 5 Amps socket outlets point controlled by one switch on the same board

All as per item No 62 herein before but One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board

All as per item No 62 above but with two run of 2.5 sqmm multi stranded Single core copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with one run of FRLSH PVC 2.5 Sqmm multi standard insulated sheathed copper wire as earth continuity conductor along with wiring and connecting to the common earth dolly on independent board.

S & F Switch piano (White) flush type single pole one way 5 Amp, 230 Volts complete all as specified.

S & F Socket outlet (White) 2 in 1, 5 pin, 5 Amps complete all as specified and directed.

S & F Switch socket combination(White) flush type multipurpose 5 pin 5 Amps two in one , 230 volts complete all as specified and as directed

S&F Switch socket combination (White) 2 in 1 5/6 pin, 15 Amp flush type universal,complete all as specified and as directed

S&F ceilling rose (White) three terminal surface bakelite type AC 50 Hz 230 Volt of size 65x50mm complete all as specified and as directed.

S & F ceiling fan regulator (White) step type, flush type heavy duty suitable to work on 230 Volt AC supply complete all as specified and as directed

S & F Lamp holder (White) with insulated body, with back plate suitable for batten fittings complete all as specified and as directed

S & F LED bulb 10 watt 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified.

S & F sheet metal enclosure MCB DB TPN , double door, 4 way with 200 amps rated bus bar 415 volts complete duly grouted laid and fixed in wall all as specified and directed.

S & F MCB TPN 63 Amps 415 Volt, confirms to IS/IEC 60898 Breaking Capacity of 10 kA, B-curve, complete all as specified and directed

S & F MCB SP, 240 volts, 6-32A Amps 50 Hz ,confirms to IS/IEC 60898 Breaking Capacity of 10 kA, B-curve, complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative ultra slim round profile LED lighting fixture with extruded polycarbonate , environmental friendly energy efficiebt ready to use pack with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 35/36 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete all as directed.

Supply and fixing ceiling fans without remote complete with blades, down rods, , fan hook and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

M & L sand cushioning in trenches for cable protection with coarse sand laid dry in trenches with uniform thickness including consolidation complete all as directed.

Supply & Laying well burnt brick , locally available best quality (sub class "B" bricks ) laid in trences perpendicular to UG Cable protection complete all as specified.

Supply & Laying XLPE LT heavy duty UG Cable of size 25 Sqmm 3.5 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armoured 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed.

S & F GI Tubing light grade of size 50mm dia in protection of cable at road crossing /hard standing/pole protection fixed with clamp as per site requirement etc all as specified and directed.

Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 50mm bore (dia) for passing of UG Cable, complete all as specified and as directed. NOTE: GI Pipe laid will be measured and paid separately under appropriate Item.

M&L earthing with GI earth plate electrode 600x600x6mm thick buried directly in ground vertically to depth not less than 2.25m below the ground level with top edge of earth plate at a depth not less than 1.5m below the ground level connected to galvanized iron wire 4mm dia earth lead by means of bolts & nuts,check nuts & washers made of galvanised steel, earth wire protected by and including PCC (1:2:4) type B1 precast RCC cover slab (1:2:4) reinforced with 8mm dia TMT bars 100mm center to center bothways including one handle made of 10 mm dia round bar, including necessary excavation and earthwork in any type of soil, 20 mm dia medium grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15 mm bore medium grade galvanized steel tubing for drawing earth wire GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 and testing on completion complete all as specified and as directed.

bkgeneralstores