SPL REPAIR TO BLOCK NO 46/11 TO 20 (JCOS/ORS MD ACCN) AT GHODA LINE AND PROVN OF NEW SEWAGE LINE CONNECTION IN OTM ACCN BLDG NOS GTC-33, 34, 37, 38, 41 AND 42 AT MIL STN KOTA

Amount

Demolition/Dismantling of existing roof treatment, any type from RCC roof slab including lime concrete/PCC padding over roof, removing layer of bitumen under lime concrete/PCC padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside MD land, complete all as specified and directed.

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL) and removing rubbish from premises, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for and removing rubbish from premises, complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid dry or laid dry and pointed complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed.

M&L brick work with old size pulverized fuel Ash-lime bricks (Fly ash bricks), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggreate), 50 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting, sub base etc, complete all as specified and directed.

M&L Providing cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (using 12.5 mm graded crushed stone agg) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for applying 10 mm thick screed in CM 1:3 on roof slabs with using liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 17.00 Contd........ (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Cost of above aspects is deemed to be included in quoted rates.

Supply only approved liquid water proofing compound, complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm bore or securing with clips, complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- S & F glass/gauge shall be measured and paid for separately.

M&L for 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides & one face is covered with decorative face veneer with lipping/frame to match & including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

S&F of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 150 mm, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 200 mm long and fixed, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised 150 mm size, complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised 100 mm size, complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws, complete all as specified and directed.

S&F 300 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S&F in renewal of 'D' type tubular towel rail 60 cm long, brass chromium plated, 20 mm dia, complete fixed with stainless steel screws, complete all as specified and directed.

Supply only 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all as specified and directed.

S & F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as applicable to item 08095 given in SSR Part – II (2020).

Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or SS wire staples complete all as specified and directed. (Cost of fixing of glass shall be deemed included in the unit rates under respective items.)

S & F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part–II.

S & F factory made steel windows conforming to IS-1038 with side hung shutters made of box type section & including box type hinges, with 2 Nos steel handles, 2 Nos tower bolts & steel pag stay complete (with glazing bars), dovetailed or welded & including fixing of lugs in PCC 1:2:4, type B-1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide/ zinc chrome primer complete all as specified and directed. Note :- Glass/SS or MS cloth wire shall be measured and paid for sepparately under respective items.

S & F factory made steel windows conforming to IS-1038 with side hung shutters made of box type section & including box type hinges, with 2 Nos steel handles, 2 Nos tower bolts & steel pag stay complete (without glazing bars), dovetailed or welded including fixing of lugs in PCC 1:2:4, type B-1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide/ zinc chrome primer complete all as specified and directed. Note :- Glass/SS or MS cloth wire shall be measured and paid for sepparately under respective items.

S & F framed work as in doors or gates of angles or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings (excluding of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing, conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: cages, frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F in renewal of stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, as in sub base of floors for levelling course to receive tiles complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over and including 25 mm thick sand cushioning, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4 backing, complete all as specified and directed.

M&L granite slab 18-20 mm thick, table rubbed and mirror polished in cooking platform, jambs, cills, pillars, tread, risers, platform for WHB etc including bull nosing to exposed outer edges, set in CM 1:4 bedding and pointing with white cement mixed with pigment, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring 18 to 20 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and mirror polishing, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for machine cut kota stone slab as in skirting, dado, risers etc, 18 to 20 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and mirror polishing, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M & L for 15 mm thick rendering on other than fair faces of brick work or stone masonry surfaces in two layers, consisting of 10 mm thick in CM 1:6 and over that 5 mm thick in Cm 1:4 using water proofing compound as per manufacturer's instruction's, finishing surfaces even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of ceiling in cement mortar 1:3 including finishing the surface even and smooth, complete all as specified and directed.

M&L for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide zinc chrome primer, complete all as specified and directed.

M&L for applying 2 coats of synthetic enamel paint over and including a coat of pink primer on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the new surfaces complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over and including a coat of suitable primer, complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying two coats of cement base paint over and including a coat of suitable primer, complete all as specified and directed.

M&L for complete removal of existing treatment from previously treated plastered/unplastered surfaces of walls and applying two coats of cement base paint over and including a coat of suitable primer, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M&L for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and directed.

M&L for applying one coat of white wash after preparation of old previously treated plastered surfaces of ceiling, complete all as specified and directed.

S&F in renewal of HDPE PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts and rubber washers complete all as specified and directed.

S&F in renewal of vitreous china wash hand basin white with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl PVC waste pipe of 32 mm bore, suitable size of waste fittings, coupling, one pair of 600 mm long cast iron brackets, etc., complete all as specified and directed.

S&F pillar taps 15mm dia, cast copper alloy, with capston heads, chromium plated, fancy type, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed.

Supply, fixing, laying & testing 15 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

S&F 50mm dia LDPE pressure pipe of pressure rating 6Kgf/Sqcm, fixed complete to walls, ceiling or floors, complete all as specified and directed.

Dismantling water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 500 ltrs capacity (cylinderical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in renewal of 15 mm dia stop valve, cast copper alloy, fancy type brass chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F in renewal of bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in renewal of vitreous china squatting pan, 'Orissa' pattern size 580mm x 440 mm, white, with front or back inlet, integral foot rest, 'P' or 'S' trap, incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

S&F in renewal of 10 Ltr capacity PVC low level flushing cistern, top push type with inlet ball valve, PVC float, brackets & including superior quality PVC flush pipe of 32 mm dia, complete all as specified and directed.

S&F in renewal CP over head shower 100mm dia round shape single flow (ABS body chromium plated with gray face plate) with rubit cleaning system, complete all as specified and directed.

S&F in renewal of kitchen sink with draining board made of stainless steel 1mm thick with plugs, washers incl brackets of suitable angle iron duly painted with two coats of synthetic enamel paint, 32 mm dia superior quality PVC waste pipe, 32 mm dia CP brass waste coupling and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm, complete all as specified and directed.

S&F in renewal of stainless steel utensil plate rack of size 900 x 1200 x 180 mm, made of 1.00 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F in renewal of PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and laid in trenches or in floors, complete all as specified and directed.

S&F in renewal of PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and laid in trenches or in floors including necessary clamps of appropriate size, complete all as specified and directed.

S&F in renewal of PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints fixed to walls including necessary clamps of appropriate size, complete all as specified and directed.

S&F PVC (SWR) bend 75 mm bore, any radius with oval and access door, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) bend 110 mm bore, any radius with oval and access door, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) 75 mm dia branch pieces, single 'Y', equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F PVC (SWR) 110 mm dia branch pieces, single 'Y', equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75 mm dia, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm dia, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F in renewal of 75 mm dia PVC (SWR) floor/nahani trap, with CP grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in renewal of PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Demolition and breaking up drain pipes 150mm dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar including bedding and haunching complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm bore of pipe complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 200mm bore of pipe complete all as specified and directed.

M&L 150 mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and directed.

M&L 200 mm bore Reinforced concrete pipes, class NP3, laid and jointed complete with collars, complete all as specified and directed.

M & L for providing cement concrete 1:2:4 type B-2 using 40 mm graded crushed stone aggregate as in surface channels and drains and benching & including finishing the top of benching even and smooth using extra cement complete all as specified and directed. Note :- Forming fair finished channel shall be measured and paid separately under respective item of the BOQ.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement & including forms, moulds mitred/stopped ends etc complete all as directed. Note :- Measurment shall be taken only for inner girth.

M&L cutting existing manholes for connecting new drain (for 150/200 mm bore pipe), making good to pipe and rendering, cutting out existing benching for forming branch channel (half round or 3/4 section) in cement concrete 1:2:4 type B-1 or smooth finishing and reforming benching as required complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in landings, cover slabs (for manholes etc), chajjas, water troughs, mangers, shelves and similar articles with plain faces & including necessary formwork & shifting to different places, set in CM 1:4, complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in excavated soil including spreading, levelling, watering and well ramming in layers not exc 25 Cm, complete all as specified and directed.

Removing excavated materials (soil) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

M & L for injecting chemical emulsion for Post constructional anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring /XLPE cable of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including providing wooden/PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surfaces, complete all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

All as per item No 105.00 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

All as per item No 105.00 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including providing wooden/PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surface, complete all as specified and directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

S & F bell push flush type 5/6 Amps 230 volts including cover plate complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, five pin, flush type universal, complete all as specified and directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, ISI marked complete all as specified & directed.

S&F in renewal of stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 50mm, 3 terminals, complete all as specified & directed.

S&F in renewal of buzzer, Ding Dong, AC, 230 volts, single pole, ISI marked complete all as specified & directed.

S&F in renewal of wall mounted 18 watt LED Tube light fittings, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed.

S&F in renewal of wall mounted 11 watt LED Tube light fittings, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed.

S&F in renewal of LED building security light fitting, 25 watt, pressure die cast aluminium housing with IP 66 deg of protection, complete with & including 0.55 m long street light bracket made of 32 mm bore GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S & F MCB TPN 63 Amps, 415 volts, four pole, B-curve, rupturing capacity 16KA conforming to IS-8828-1996, IEC-60898, complete, all as specified & directed by Engineer-in- charge.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, IP-43-IK09 protection grade, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed. Note for items of MCB DB - (1) The unit rate includes for cutting the brick/stone walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. NOTE for items of submain wiring:- Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 5 and including dismantling and taking out old earthing complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth wire upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized earth strip of 25x4 mm dia by means of bolts, buts, check nuts and washers of galvanized iron on steel including 40 mm bore light grade GI tubing for protection of earth strip, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar including necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 3 and including dismantling of old u/s earthing complete all as specified and directed.complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 3 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth lead strip upto 7.5 m.

Supplying, installation, commissioning and testing (including CPRI type test certified) of outdoor type, weather proof, factory made feeder pillar box (Kiosk) of suitable size (as per Indian Electricity Rules) and suitable for working on 3 phase, 4 wire, 415 volts, AC, 50 Hz cubicle, floor mounted, free standing, dust air vermin proof air ventilation, protection class IP-54 made of 3.15 mm thick CRCA sheet duly powder coated, having double door opening (front & rear) with locking arrangement, provision of entry & exit CP brass glands for cables, having bus bar chamber with 4 No heat shrink insulated aluminium bus bar of 600 Ampere capacity and including all connection with aluminium busbar strip, provided with danger notice plate with skull & bone sign, including making all electrical incoming and outgoing electrical cable connection with new lugs, gland to be provided at cable entries and including MS channel frame of ISMC 75 work at the base of panel only for grouting purpose & necessary cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) for grouting of panel stand and connecting the panel with existing earthing and including dismantling of old u/s existing panel comprising of the following: -

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm with and including PVC insulated three core 23/.0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high and including making appropriate hole in the wall/ window complete all as specified and directed.

S&F in renewal of electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. & including connecting with and including PVC insulated three core 23/.0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high complete all as specified and directed.

Supplying, laying, jointing testing and commisioning XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade of cross-sectional area 70 Sqmm, 3.5 core, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall, complete all as specified and directed.

Supplying, laying, jointing testing and commisioning XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade of cross-sectional area 25 Sqmm, 3.5 core, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall, complete all as specified and directed.

M&L dry clean Sand filling in trenches around underground cables for earth cushion, complete all as specified and directed. Note: - Depth of sand shall be measured after punning.

Supplying and laying pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), laid flat adjoining each other as in protection to UG cables, complete all as specified and directed.

Cutting of road / hardstanding upto a size not exceeding 20 cm in width and not exceeding 60 cm in depth for laying of LT UG cable protection pipe line, making good the disturbed portion so as to match existing finishing or with PCC 1:2:4 type B1 complete all as specified and directed.

M&L in renewal of 40 mm bore Steel water tubing, light grade, galvanised, with all fitting, laid in trenches/fixed to walls/poles etc as protection to cables, with and including necessary MS clamps, nuts botls, washers etc required for fixing, complete all as specified and directed.

M/S. EAST ENGINEERS

K B ENTERPRISES

triveni sales corporation

Ganesh Contruction

M/s Prem Associates