ADDN ALTN AND SPECIAL REPAIRS TO BLDG NO P-306 (MSRS COMPLEX) OF HQ 33 WEU AT INS GARUDA AT NAVAL BASE KOCHI

Amount

S&F aluminium powder coated frame work for partition including 12mm thick prelaminated partical board (area of panel not exceeding 1.50 sqm each) with out sash bar,including all necessary jointing leats,hold fasts,hinges with fixing clips,rubber gasket,anodised snap beading,anodised aluminium fittings,locking arrangement etc (minimum thickness of powder coating 50 micron). Section used for partition is catlogue No 9223 of size 63.58x38.10x2.00 mm (single partition vertical &horizontal sections) of Hindalco or equivalent make as approved by GE complete all as specified and as directed .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L Vitrified Ceramic tiles 10mm to 12 mm thick (square/ rectangular) any shade approved by Engr-in-Charge, polished, area of each tiles exceeding 0.42 sqm but not exc 1.00sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick screed bed in CM 1:4.Thickness of tile shall be as per approved manufacture instructions

All as per item No 3 above but in skirting over 10mm thick backing coat in cement mortar 1:4

M&L for coloured Ceramic tile 10mm to 12mm thick of area of each tile exc 0.42 sqm but not exc 1.00sqm with approved pattern and colour borders over cement screed 10 mm thick in CM 1:4 complete all as specified and directed.Thickness of tile shall be as per approved manufacture instructions

M&L for coloured Ceramic tile 10mm to 12mm thick of area of each tile exc 0.42 sqm but not exc1.00 sqm joint free in skirting over cement backing coat 10 mm thick in CM 1:4 complete all as specified and directed.

M&L for Glazed ceramic tiles coloured , as in vertical surfaces, 7mm to 8mm thick area of each tile exc 0.11 sqm and not exc0.18 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles including 10 mm thick rendering in CM 1:3 complete all as specified and directed.

Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set in cement screed bed 10mm tk in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in levelling course in floor and mass concrete complete all as specific and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L for Pre-cast cement concrete block masonry with solid blocks type C1, 1:3:6 (20 mm graded aggregate), exc. 10 cm in width and setting in 1:6 cement mortar, complete

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M & L for rendering 8 mm thick plaster in CM 1:4 mixed with 3% WPC over 12mm thick backing coat in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and fair without using any extra cement. (Note: WPC shall be measured seperately)

Supply only Liquid water proofing compound.

M&L for rendering cement plaster 1:6 10 mm thick incl finishing even and smooth without using with out extra cement on internal faces.

M&L for cement plaster 1:3, 5 mm thick incl finishing even and smooth without using extra cement on ceiling/ chajja.

Taking down Chowkats with shutters of area exc 1.5 Sqm but n.exc 4.00 Sqm each without taking off shutters from frame.

Taking down chowkats or frames not exc 1.5sqm each with shutters( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts.

Taking down of shutters of any description exc 1.00 Sqm and n.exc 2.00 sqm each

Re fixing of shutters of any description exc 1.00 Sqm and n.exc 2.00 sqm each in same opening including of taking down, easing, adjusting and renewal/re fixing of builders hardware as required including renewal of unserviceable screws, etc.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube

S&F Factory Made Solid PVC Moulded Door Shutter,with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

M&L for preparation of old wooden surfaces of any description and applying one coat of synthetic enamel paint complete all as specified.

M&L for preparation of old steel surfaces of any description and applying one coat of synthetic enamel paint complete all as specified and as directed.

S&F extruded aluminium anodised handle 125 mm fabricated type polished and fixed with stainless steel screws.

Supply and fix stainless steel butt hinges medium weight size 100mm size complete all as specified and as directed

M&L for 100 mm Aluminium anodised barrel tower bolts of extruded section rolled and fixed with stainless steel screws.all as specified

S&F in repairs for Vitreous China wash down water closet pan (pedestal pattern), white with Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device. Make : Hindware/Cera

S&F in repair Vitreous China Urinal, Half stall type, white all as specified excluding flushing pipe and waste pipe in repairs.

S&F in repair vitreous china ware wash hand basin white, oval shape, size 550x400 mm size including cutting for and pinning ends of brackets or erecting stand fixed in repairs.Make :Jaquar FLS WHT 5701 or equivalent

S&F 32 mm waste coupling of PTMT (half or full threaded) (Minimum weight 32 mm-45 gms complete all as specified and directed.

S&F in repair 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F in repair 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets.

S&F PVC connection 15 mm bore 45 cm long with brass coupling.

Complete removal of existing treatment of exterior surface including washing, rubbing down stopping of distempered and painted surfaces

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new or old surfaces.

M&L for complete removal of existing surface treatment and applying two coats of oil bound distemper over a coat of primer and 1.5mm thick wall putty complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of primer and 1.5mm thick wall putty complete all as specified and directed.

M&L for preparation of new surfaces of ceiling surfaces and applying three coat of white wash.

M&L for preparation of old surfaces of ceiling by brooming down or by steel wire brushing and applying two coat of white wash.

M&L for applying one coat of oil bound distemper on old surfaces of false ceiling board complete all as specified.

S&F powder coated anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F for powder coated Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified

S & F for 15 mm thick both sides pre laminated Particle board, exterior grade, fixed with screws to frame work in table top, cup board shutters, partitions, shelves etc. complete all as specified and directed.

S & F 5.5 mm thick sheet glass ordinary quality and glazing with oil putty square n.exc0. 5 sqm in each pane complete all as specified and directed.

S&F solar sun control film 25 micron reflective type exc 1.5sqm

S&F Door closer cast iron body hydraulically regulated,designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.

Dismantling of wall and ceiling boards (fibre, pulp insulation etc.) or insulation boards / slabs / blankets, any thickness including fillet (except ceiling)

S&F in repair 605 x 605 mm/600x600mm size of grid Anodised aluminium snap grid frame work (Main Tee 38X25X1.40mm and Cross Tee 25X25X1.2mm wall angle 25X25X1.30) for false ceiling incl 3mm dia Galvanised mild steel plain wire hangers complete all as specified and directed.

S & F 4 mm thick Non asbestos fibre cement building boards fixed or laid / inserted to timber / GI / Aluminium frame work with screws in ceiling flat or sloping complete all as specified and directed.

M&L for 12mm thick perforated mineral fibre board/tiles for insulation and accoustic purpose 595x595mm/600mmx600mm in size fixing on snap grid frame work in ceiling in flat or in sloping complete all as specified as per manufactures instructions

5mm thick printed PVC sheet in strips & channel feathered at edges for fixing on solid PVC wall lining,insulated PVC wall lining,and solid PVC partitions inclusive of solvent cement and fixing at site complete all as specified

M&L 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

M&L for 15 mm thick perforated mineral fibre board/tiles for insulation and accoustic purpose 595x595mm/600mmx600mm in size fixing on MS frame work in walling complete all as specified as per manufactures instructions

M & L for mild steel frame work for wall panelling fixed with screws to walls

M&L for two coat of synthetic enamel painting on steel surfaces over a coat of primer including preparation of surfaces not exc 10 cm width or girth.

M&L for 40mm thick bonded mineral wool blanket slab made from glass density 24 kg/cum and fixed as per manufactures instruction complete all as specified

S&F in repair Vitreous china urinal partition white of size 310x700 mm all as specified and as directed by Engr -in-Charge.

Dismantling of single layer Mangalore pattern tiles with roof tiles or slate roofing complete

S & F tile for Mangalore pattern tile roofing, laid dry complete all as specified and directed.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 100mm thick cement concrete type D2, 1:4:8 (40 mm graded aggregate) as in sub base complete all as specified and as directed by Engr-in-Charge.

M&L for hard core of broken stone or boulder gauge n exc 63mm deposited spread and levelled in layers n exc 15cm thickness watered and rammed to a true surface Moorum/Earth filling shall be properly compacted Complete all as specified and as directed by Engr in Charge.

Supplying and laying 400 micron thick HDPE sheet (Virgin Quality) water proof, wrinkle free without puncture having minimum weight 390 gm/Sqm aver tack coausand cushion as specified in the design with overlap between adjacent strips and at transverse joints as minimum 300mm. complete all as specified and directed by Engineer-in-Charge

M& L for moorum/red bajri filling in floors laid in layers not exc 15 cm thick spread levelled and watered and properly compacted.

M&L for RCC M30 design mix for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L for Mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L PCC (1:3:6) Type C-2 using 40mm graded stone aggregate) as in foundation or post holes all as specified.

Dismantling fencing wire mesh, any type.

Dismantling wrought iron or mild steel work of any description not otherwise provided including taking out embedded portion in concrete, brick work etc all as specified and directed.

S&F MS Hand rails, half round or other steel section or core for wooden hand-rail straight portion,drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F 610mm dia punched tape concertina coil (supported on MS Angle iron frame and barbed wire all as specified) manufactured using central core of high tensile GI Spring steel core wire of 2.60mm di around which a tape of razor sharp blades (low carbon GI strips) of thickness 0.52mm is machine crimped with following specifications:- a) Dia of coil (unstretched) = 610mm b) No of circles = 51 turns per coil c) Wt of each coil with Hessain cloth = 8.50Kg(+/- 0. Kg) d) Coverage per coil = 8 RM e) Dove tail clips shall be grade A as per IS 2062 and hot dip galvanised with 20microns or 290gms/Sqm, 5 Clips per 2 spiral turns approx 125 clips per coil. f) The tensile strength of spring steel core wire shall be 1620 N/Sqmm (min) all as per IS 4454/part I with zinc coating of 230gm/Sqm as per IS 2629. g) Punched tape shall be matt finish with average coating of galvanisation of 18 microns Note:- (i) MS Angle iron frame & barbed wire shall be measured and paid separately. (ii) The concertina coil shall be tied to barbed wire with 1.2mm GI wire.

S& F galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins etc as directed

M&L prepration of new steel surface and applying two coats of synthetic enamel paint over one coats of red oxide preparation of new surfaces over 10 cm width on ginth.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces complete all as directed by the Engineer- in Charge.

M&L for 15mm thick cement plaster with cement mortar 1:4 finished even and smooth with out using extra cement complete all as specified complete all as directed by the Engineer- in Charge.

M&L for applying two coats of cement base paint over a priming coat after preparation of newly plastered/concrete surfaces complete all as specified and directed by the Engineer- in Charge.

M&L for preparation of old decorated surfaces of walls including cornices (plastered or unplastered) and appling two coat of cement base paint all as specified and directed by Engr -in-Charge .

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, sheet metal encl. with plug & socket etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L point wiring with 1.5 Sqmm PVC insulated unsheathed FRLSH multistranded single core copper conductor cable in PVC concealed conduit rigid non metallic ( ISI marked ) fixed concealed on wall /roof except beam, column and RCC roof including chases cutting incl 1.5 Sqmm PVC insulated copper conductor as earth continuity wire for the following:-

One light point controlled by one switch complete all as specified and as directed by Engineer-in-Charge.

One fan point / exhaust fan point controlled by one switch & regulator complete all as specified and as directed by Engineer-in-Charge.

One 5 pin 5 Amps Socket point controlled by one switch on same board complete all as specified and as directed by Engineer-in-Charge.

One 5 pin 5 Amps socket point controlled by one switch on independent board complete all as specified and as directed by Engineer-in-Charge.

All as per item No 84 above but with 2.5 Sqmm copper conductor including 2.5 Sqmm copper cable as earth wire for one 6 Pin 16 Amps Socket outlet on independent board complete all as specified and as directed by Engineer-in-Charge.

All as per item No 84 above but with 4 Sqmm copper conductor including 4.0 Sqmm copper cable on earth wire for sheet metal enclosure for AC point complete all as specified and as directed by Engineer-in-Charge.

S&F modular switch 1 way 6 Amps,1 module complete all as specified and as directed by Engineer-in-Charge.

S & F Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body complete all as specified and as directed by Engineer-in-Charge.

S & F socket modular 6 Amps and 2/3 pin combined 2 module complete all as specified and as directed by Engineer-in-Charge.

S & F Modular socket 6 A/16 A - 2/3 pin combined 2 module complete all as specified and as directed by Engineer-in-Charge.

S&F switch 15 A One way SP modualr type complete all as specified and as directed by Engineer-in-Charge.

Supply & fix Regal Batten for LED tube lights, both side connection type and LED tube rod 1 x 22 Watt, both side connection complete all as specified and as directed by Engineer-in-Charge. Make of batten : Havells Cat Part No. REGALBATTENT8UPTO1X22WDSBSWH / Crompton Cat Part No. IGP131LT8-16 / Philips Cat Part No. TMC501P1XTLED22WP3241

Supply and lay GI tube light grade galvanised with all fittings 40 mm bore for protection of UG cables under roads / culverts / floor or fixed on walls / poles.

Supply and lay GI tube light grade galvanised with all fittings 50 mm bore for protection of UG cables under roads / culverts / floor or fixed on walls / poles.

Supply & fix LED recessed mounted down lighter 2'x2' , 36 W, 120 Lumen/ Watt, 240 volt complete all as specified and as directed by Engineer-in-Charge. Make Havells Cat Part No. VENUSNEOHE2X2R36WLED840PIRSENSOR and driver LEDDRIVER36V36WS or Crompton Cat Part No. LCTLRN-36-FO-CDL/ Philips Cat Part No. RC380BLED36S-6500G4L60PSUOD.

Supply & fix LED surface mounted down lighter 2'x2' , 36 W 240 volt, 120 Lumen/ Watt, complete all as specified and as directed by Engineer-in-Charge. Make Havells Cat Part No. PLANOSUR4X1PLS36WLED857S0720 or Philips/ Crompton

Supply & fix LED down lighter, round or square, 12 W,240 volt, 120 Lumen/ Watt, complete all as specified and as directed by Engineer-in-Charge. Make Polycab Cat Part No.LD001200041 or Crompton Cat Part No. LSDEP-12-CDL / Philips Cat Part No. 94051090

S & F for LED Mirror light fitting 8 watt, 100 Lumen/ Watt, with connected accessories complete all as specified and as directed by Engineer-in-Charge. Make :Polycab Cat Part No. LD00103040 or Crompton Cat No. LDL-10-WW, Luker Cat Part No. LTSM10

S&F fan regulator electronic step type, 230 V, 5 step, modular type, 120 W, 2 module complete all as specified and as directed by Engineer-in-Charge.

Taking down ceilingfan, Painting of celing fans complete, including taking down rods in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and hanging in original as directed position and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and as directed by Engineer-in-Charge.

Taking down existing wall mounting fans of any make and size including servicing, cleaning, oiling (painting if required) all as per site requirement and refixing the same on existing/proposed location complete all as specified and as directed by Engineer-in-Charge.

Taking down existing wall mounting fans of any make and size including servicing, cleaning, oiling (painting if required), winding with super enamelled copper wire of exisitng size and gauge including heating, baking and re-assembling all as per site site requirement and refixing the same on existing/proposed location complete all as specified and as directed by Engineer-in-Charge.

Taking down existing ceiling fans of 1200 mm sweep complete and removing to workshop for following repairs & re-fixing at any location complete all as specified and as directed by Engineer-in-Charge. (a) Strip opening/ cutting of the ceiling fan and rewinding with super enamelled copper winding wire of same capacity, heating, baking, sleeves, varnish etc. (b) Replacement of ball bearings of suitable size. (c) Replacement of fan capacitor 2.5 m.f.d

All as per item No. 103 above but for exhaust fans of 300/380 mm sweep including necessary welding to the brackets, frame etc as per site requirement complete all as specified and as directed by Engineer-in-Charge.

S&F energy efficient ceiling fan of 1200mm sweep 230 Volt 50 Hz including all electrical connection complete all as specified and as directed by Engineer-in-Charge. Make :- Atomberg Cat Part No. AMEZA/ Orient Model Ecotech Neu BLDC 5 star/ Gold Medal Cat Part No. GEO FOX White. Note : Old fans to be deposited with MES store yard.

S&F 300 mm sweep, metal body exhaust fan heavy duty, single phase 230 Volts, complete all as specified and as directed by Engineer-in-Charge. Make: Havells/ Usha or equivalent make in the approved manufactures list. Note : Old fan will be deposited in MES store yard.

S&F 250 mm sweep, PVC body exhaust fan heavy duty, single phase 230 Volts, complete all as specified and as directed by Engineer-in-Charge. Make: Havells Cat Part No. Ventil Air-DX White or Crompton / Bajaj. Note : Old fan will be deposited in MES store yard.

Taking down existing MCB DB SPN with MCBs of any type and size complete all as specified and as directed by Engineer-in-Charge.

Taking down existing MCB DB TPN with MCBs of any type and size all as specified and as directed by Engineer-in-Charge.

S & F Power Unit 25 Amp modular type for Acs Make Havells Cat Part No AHOO002504 complete all as specified and as directed by Engineer-in-Charge.

Taking down existing Power unit of any type and size and removing to store yard complete all as specified and as directed by Engineer-in-charge

S&F Sheet metal enclosure Vertical TPN for DB's when MCCB's to be used 12 way with 250 amps bus bar double door IP 43 metal door complete all as specified and as directed by Engineer-in-Charge. Make L&T cat No DBVTL012DD / Legrand / ABB

S&F Sheet metal enclosure Vertical TPN for DB's when MCCB's to be used 8 way with 250 amps bus bar double door IP 43 metal door complete all as specified and as directed by Engineer-in-Charge. Make L&T cat No DBVTL008DD / Legrand / ABB

S&F Sheet metal enclosure Vertical TPN for DB's when MCCB's to be used 6 way with 250 amps bus bar double door IP 43 metal door complete all as specified and as directed by Engineer-in-Charge. Make L&T cat No DBVTL006DD / Legrand / ABB

S&F SPN sheet metal enclosure for DB 12 ways Double door complete all as specified and as directed by Engineer-in-Charge.

S&F SPN sheet metal enclosure for DB 8 ways Double doorcomplete all as specified and as directed by Engineer-in-Charge.

S&F SPN sheet metal enclosure for DB 4 ways Double door complete all as specified and as directed by Engineer-in-Charge.

S&F MCCB 3 pole, 415 Volt fixed type 125 Amps with breaking capacity 16 KA complete all as specified and as directed by Engineer-in-Charge.

S&F MCCB 3 pole, 415 Volt fixed type 200 Amps with breaking capacity 36 KA complete all as specified and as directed by Engineer-in-Charge.

S&F MCB 'C' Curve 100 Amp Three pole, 415 Volts complete all as specified and as directed by Engineer-in-Charge. Make L&T Cat Part No. AU15S31003C or Legrand Cat Part No. 408663/ Schneider Cat Part No. A9N18367

S&F MCB 'B' Curve 63 Amp Three pole, 415 Volts, complete all as specified and as directed by Engineer-in-Charge. Make L&T Cat Part No. BB30630B or equivalent manufacturers mentioned in list of manufacturers

S&F MCB 'C' Curve 40 Amp SPN ,240 Volts complete all as specified and as directed by Engineer-in-Charge. Make L&T Cat Part No. BB20400B or Schneider Cat Part No. A9NIP40B/ Legrand Cat Part No. 408618

S&F MCB 'C' Curve 40-63 Amps SP ,240 Volts complete all as specified and as directed by Engineer-in-Charge.. Make L&T Cat Part No. BB20032B or equivalent manufacturers mentioned in list of manufacturers

S&F MCB 'C' Curve SP 6 To 32 Amp , 240 Volts, complete all as specified and as directed by Engineer-in-Charge. Make L&T Cat Part No. BB10060B to BB10320B or equivalent manufacturers mentioned in list of manufacturers

Taking down old sub main wiring of any type and size and removing to store yard, making good disturbed wall surfaces matching with existing surfaces complete all as specified and as directed by Engineer-in-Charge.

M/L submain wiring with 2 single core 4 Sqmm PVC insulated unsheathed multistranded copper conductor cable 1100 volt grade drawn throgh and including PVC rigid conduit concealed wiring inculding necessary PVC conduit specials including chases cutting complete exceapt beam and RCC roof and one run of 4Sqmm PVC insulated unshearthed single core 1100 volts grade multistranded copper conductor cable as earth continuity conduto9r and connceting with suitable size thimble complete all as specified and as directed by Engineer-in-Charge. Note: two run of 4 sqmm size PVC cable , one run of 4 Sqmm size PVC cable as earth wire and one run of PVC conduit shall be measured as one unit length.

All as per item No 126 but 2 single core 6 Sqmm with 6 Sqmm earth wire complete all as specified and as directed by Engineer-in-Charge.

All as per item No 126 above 4 runs of 6 Sqmm PVC copper conductor including 2 runs of 6 Sqmm copper conductor as earth wire complete all as specified and as directed by Engineer-in-Charge.

All as per item No 126 above but with 4 single core 10 Sqmm PVC insulated copper conductor with 2 run 10 Sqmm copper conductor as earth wire complete all as specified and as directed by Engineer-in-Charge.

Taking down of existing unserviceable earthing of any type with strips, junction boxes, earth plates complete all as specified and as directed by Engineer-in-Charge.

M&L in repair earthing complete with galvanised steel earth plate electrode 60 cm x 60cm x6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meters below normal ground level, connected to GI earth strip 25x4 mm upto length 7.5 mtr by means of bolts, nuts and washers of galvanised steel all as shown in electrical plate No. 3 connected to earthing test point complete all as specified and indicated including testing on completion including taking out old earthing complete. Note : The rate is deemed to be inclusive of the cost of complete earth work in any type of soil. PCC 1:3:6 type C-1 for chamber,RCC 1:2:4 type B1 for cover slab 50 mm thick, reinforcement 8 mm CTD bars @ 100 mm c/c both way, necessary form work, handle, charcoal dust 20mm dia GI med grade for watering and 40mm dia GI med grade earth lead protection pipes with funnel and wire mesh complete all as specified and as directed by Engineer-in-Charge.

Taking down existing Aviation Lights/ Flood Lights/ Building Security Lights of any type or make or at any height and removing to store yard complete all as specified and as directed by Engineer-in-Charge.

S&F Integral aviation obstruction light fitting of 10 Watt, 120 Lumen / Watt, 230 Volts, 50 Hz comprising of aluminium housing with polycarbonate inclouser including fixing arrangement and connection complete all as specified and as directed by Engineer-in-Charge. Cat part no BGAV 302 LED of bajaj or Philips/wipro .

Supply and fixing building security light made up of pressure die cast housing with toughened glass and high power LEDs with option of secondary optic with IP 66 protection of 45 Watt , 120 Lumen/ Watt, including complete all as specified and as directed by Engineer-in-Charge.all as specified and directed. Make : Crompton Cat Part No. LSTS-45-CDL-M or Philips HSN code 94054090/ Jaguar Cat Part No. LPCRSRT45WXW.

Same as Item No. 134 above, but of 100 Watt complete all as specified and as directed by Engineer-in-Charge. Make : Crompton Cat Part No.LSTP-100-CDL-M or Philips HSN code 94054090/ Jaguar Cat Part No. LPCRSRT100WXW.

S&F LED flood light made up of pressure die cast housing with toughened glass and high power LEDs with option of secondary optic with IP 66 protection, 3000 K, with 10 KV SPD of 50 watt complete all as specified and as directed by Engineer-in-Charge. Make : Crompton Cat Part No. LFL-50-CDL/60-M or Jaguar Cat Part No. LFLD02S050XW/ Philips Cat Part No. BVP 161 LED 43 NW/CW/WW 50W.

Taking down existing LT cable of any type and size for reuse or taking credit complete all as specified and as directed by Engineer-in-Charge.

M&L for refixing of cables of any type and size for building security lights obtained as per item No. 55 above on walls with clamps, screws etc complete all as specified and as directed by Engineer-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) on walls with clamps, saddles, screws etc for building security light of 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core complete all as specified and as directed by Engineer-in-Charge.

All as per item No. 139 above but for 16 sq mm 2 core complete all as specified and as directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft soil complete all as specified and directed by eng-in-charge

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by eng-in-charge

Supplying and laying reinforced precast concrete cable cover,Class LV, Type I, flat, size 250mm x 150mm x 40mm complete all as specified and directed by eng-in-charge

Supply, Fill, Spread and ramming / consolidation in layers, dry river sand in trenches for cushioning and covering of UG cables all as directed.

Removal of excavated soil to a distance not exc 50 mtrs and depositing where directed at a level not exc 1.5 mtr above the starting point all as directed.

Supply and fixing street light control panel, three phase 6 KW load with 24 hour Digital timer, Contactor rating 32 Amps TP, MCB rating 40 Amps TPN including taking down old one of any type/size complete all as specified and as directed by Engineer-in-Charge.. Make : Havells Cat Part No. IHXTS03060

Supply and Fixing PVC Junction box, with 2 x Aluminium busbar and one MCB SP 6 Amps for controlling street/ security lights water tight including taking down old one complete all as specified and as directed by Engineer-in-Charge. Make : Syntex

Taking down and refixing of telecommunication cables, network cables, electrical cables etc along with PVC conduits at necessary location complete all as specified and directed by Engr-in-Charge.

Supply and fix Rigid non-metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed by Engr-in-Charge.

Taking down Exhaust fan, Painting of Exhaust fan complete, including taking down rods in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and hanging in original as directed position and connecting up including provision of cable from ceiling rose or connector to exhaust fan complete all as specified and as directed by Engineer-in-Charge.

Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessay fittings, solvents of size 40 mm dia complete all as specified and directed by Engineer-in-Charge.

All as per item No 151 here-in-before but of size 25 mm dia complete all as specified and directed by Engineer-in-Charge.

All as per item No 151 here-in-before but of size 20 mm dia complete all as specified and directed by Engineer-in-Charge.

S&F CPVC Ball Valve of size 25 mm dia suitable for CPVC pipe incl necessary fittings complete all as specified and directed by Engineer-in-Charge. Make: Supreme or equivalent manufacturers mentioned in list of manufacturers

S&F CPVC Ball Valve of size 20 mm dia suitable for CPVC pipe incl necessary fittings complete all as specified and directed by Engineer-in-Charge. Make: Supreme or equivalent manufacturers mentioned in list of manufacturers

Supply and fixing of Bib tap CP, Quarter turn with flange and areator, fancy type Long body cast copper alloy with crutch or butterfly handle screwed for GI/cpvc pipe of size 15mm , complete all as specified and as directed by the Engineer-in-charge.(Make : Model No F2008152 of Cera or equivalent manufacturers mentioned in list of manufacturers)

Supply and fixing of CP Bib cock short body with flange and nozzle for garden/ washing machine of size 15 mm including necessary fixing accessories with GI/ CPVC pipes and taking down old unserviceable tap of any make complete all as specified and as directed by the Engineer-in-Charge. (Make : Cera Model No. F F2002153 or equivalent manufacturers mentioned in list of manufacturers)

Supply and fixing 15mm angle valve,quater turn with flange, with flange type chromium plated for fixing with CPVC pipe complete specified and as directed by the Engineer-in-charge.(Make : Model No: F8040204 of Cera or equivalent manufacturers mentioned in list of manufacturers)

Supply and fixing two way angle cock with flange 15 mm, chromium plated for fixing with CPVC pipe complete specified and as directed by the Engineer-in-charge.(Make : Model No: F2002211 of Cera or equivalent manufacturers mentioned in list of manufacturers)

Supply and fix concealed stop cock regular body,Quarter turn with adjustable wall flange chromium plated with CP cup fancy type of size 20mm and taking down old unserviceble one, complete all as specified and as directedby the Engineer-in-charge.(Make : Model NO: F2002362 of Cera or equivalent manufacturers mentioned in list of manufacturers)

Supply and fixing health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe , complete all as specified and directed by Engineer-in-Charge.(Make : Model No: F8030108AB of Cera or equivalent manufacturers mentioned in list of manufacturers)

Supply and fixing of swivel overhead shower of PTMT any colour with shower arm 15 mm size, 195 mm long with bend of 45 degree with flange for fixing with CPVC pipe and all as specified and as directed by the Engineer -in-Charge. Cat Part No. F7020108AB of Cera or equivalent manufacturers mentioned in list of manufacturers

S & F wall mixer (3- in - 1) with arrangment of both Telephonic shower and over head shower with 210 mm long bend pipeand taking down old unserviceble one complete all as specified and as directed by the Engineer in Charge . Make :CERA , Model : F1015403 or equivalent manufacturers mentioned in list of manufacturers

Supply and fixing CP angle cock, self closers/ pressmatic with wall flange for urinal pots to fixed in 20/15mm pipe, complete all as specified and directed by the Engineer -in-charge (Model No F9020203 of CERA or equivalent manufacturers mentioned in list of manufacturers

S&F sink cock wall mounted with 6 inch long swivel spout and wall flange complete all as specified and directed by Engineer-in-Charge. Model No. F1018251 of Cera or equivalent manufacturers mentioned in list of manufacturers

Supply and fixing PVC connection pipe 16mm dia (outer 450mm long cold water complete with brass union on both sides to suit 15mm pipe complete all as specified and directed by the Engineer-in-charge.

Supply and fixing of Rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted & fixed in position of capacity 2000 liters including inlet, outlet, over flow wash out and Air pipe conncetions complete all as specified and directed by Engineer-in-Charge. Make : Sintex (ISI)/ Aquatech

Same as item No. 167 above but for 1000 Ltrs capacity complete all as specified and directed by Engineer-in-Charge.

Same as item No. 167 above but for 500 Ltrs capacity complete all as specified and directed by Engineer-in-Charge.

S/F float valve synthetic(PVC) of size 25 mm dia high pressure with polythene ball of size 6" dia and flynut complete all as specified and directed by Engineer-in-Charge.

Taking down old GI/ CPVC pipe of size 20 mm complete all as specified and directed by Engineer-in-Charge.

Taking down old GI/ CPVC pipe of size 25 mm complete all as specified and directed by Engineer-in-Charge.

Taking down old GI/ CPVC pipe of size 40 mm complete all as specified and directed by Engineer-in-Charge.

Taking down old CPVC ball valve of size 20 mm /25 mm complete all as specified and directed by Engineer-in-Charge.

Taking down old bib tap, angle valve, health faucet, angle cock complete all as specified and directed by Engineer-in-Charge.

Taking down old swivel overhead,sink cock complete all as specified and directed by Engineer-in-Charge.

Taking down old rotational moulded polythene water storage tanks of capacity 2000 ltrs complete all as specified and directed by Engineer-in-Charge.

Taking down old rotational moulded polythene water storage tanks of capacity 1000 litres complete all as specified and directed by Engineer-in-Charge.

Taking down old rotational moulded polythene water storage tanks of capacity 500 litres complete all as specified and directed by Engineer-in-Charge.

Taking down old PVC connection complete all as specified and directed by Engineer-in-Charge.

S&F air termination single pointed aluminium rod 12 mm dia and 300 mm long complete all as specified and as directed.

S&F test point terminal block made of gun metal or phosphorus bronze size 75 x 75 25 mm, and screwed including 3 Nos 8 mm dia 25 mm long hexagonal head screw including PVC junction box complete all as specified and as directed.

S&F aluminium strip 25 x 3.15 mm with saddles, insulators and fixing screws etc for roof conductors and down conductors on walls/above ground complete all as specified and as directed.

M&L earthing complete with galvanised steel earth plate electrode 60 cm x 60cm x6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meters below normal ground level, connected to GI earth strip 32x6 mm as earth lead 7.5 mtrs by means of bolts, nuts and washers of galvanised steel all as shown in electrical plate No. 3 connected to earthing test point complete all as specified and indicated including testing on completion including taking out old earthing complete. Note : The rate is deemed to be inclusive of the cost of complete earth work in any type of soil. PCC 1:3:6 type C-1 for chamber,RCC 1:2:4 type B1 for cover slab 50 mm thick, reinforcement 8 mm CTD bars @ 100 mm c/c both way, necessary form work, handle, charcoal dust 20mm dia GI med grade for watering and 40mm dia GI med grade earth lead protection pipes with funnel and wire mesh complete all as specified and as directed.

M&L for one coat of antifungal paint over a coat of primer over MP tiles laid on sloped roof

Supply and fixing 15mm angle valve,quater turn with flange, with flange type chromium plated for fixing with CPVC pipe complete specified and as directed by the Engineer-in-charge.(Make : Model No: F2002152 of Cera or prayag/ hindware)

Supply and fixing PVC connection pipe 16mm dia (outer 450mm long cold & hot water complete with brass union on both sides to suit 15mm pipe complete all as specified and directed by the Engineer-in-charge.

Supply and fixing vertical type Geyser (Water Storage Heater) 25 litres, 230 volt., 50 Hz, working pressure 0.8 mpa with storage tank of mild steel material 5 star rating including necessary grouting complete all as specified and directed. Make : V-Guard Cat Part No. SPRINHOT PLUS or equivalent manufacturers mentioned in list of manufacturers complete all as specified and as directed.

S&F Sheet metal enclosures with socket plug top and MCB' single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 A MCB complete all as specified and directed by Engr-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) on walls with clamps, saddles, screws etc for building security light of 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and as directed by Engr-in-Charge.

M.J.JOY AND COMPANY (BID ID -3360337)

K THOMAS AND COMPANY (BID ID -3362232)

M/s Antony Kallarakkal (BID ID -3361813)

M/s ANTONY THOMAS AND CO (BID ID -3368883)

SUKU CONSTRUCTIONS (BID ID -3361686)

Powertech Engineers (BID ID -3361975)

SHAIJAL T M (BID ID -3370076)