DEPOSIT Renovation and modification of OH water tank building for providing infrastructure facilities for setting up of Molecular Diagnostic Lab in GMCTCR work General Civil Work

Amount

APPENDIX-A-CIVIL WORK

15.23.1:Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

OD36767/2022-2023:Providing and laying vitrified floor tiles (double charged/full body-glassed/mat finished of brands of best quality or equivalent brands,having quality certificates and with crazing test,water absorption test,flexural strength,mohra hardness test etc / using spacers if necessary of minimum dimension of tile 600mm and above (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete as per the direction of the Engineer in charge.

OD34828/2022-2023:null Clearing and removing grass, small bushes and other dirty matters from open terrace and sunshade of building and disposal of the debris to a safe distant place including all labour charges, scaffolding charges, hire charges etc. complete, as per the direction of departmental officers at site.Upto floor V level.

14.43:Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

13.85.3:Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre

OD36830/2022-2023:Painting Redimixed anti fungal apex paint of approved Quality as specified with priming coat after rubbing with sand paper and cleaning the surfaceincluding all labour, material, conveyance charges etc complete.

11.36:Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

11.37:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

14.53.1:Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work

14.54.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade:One or more coats on old work

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.2.2:Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

18.48:Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

OD34826/2022-2023:Providing G.I. hard colour powder coated trafford sheet 0.40mm thick roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces),excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.4.2:Providing ridges or hips width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gm/m2

OD34827/2022-2023:null supplying and fixing 110 mm PVC (4kgf/cm2)pasted to collect rain water

OD34829/2022-2023:Cleaning and desilting of gully trap chamber, including removal of rubbish mixed withearth etc. and disposal of same, all as per the direction of Engineer-in-charge.

OD34830/2022-2023::Removing the blocked materials from the sullage water drain around the building and depositing the dirty matters to a safe distant place within a distance of 150m etc. complete, including cleaning the drain uprooting the vegetation and all labour charges etc. complete, as per the direction of departmental officers at site.

OD34831/2022-2023:Supplying and fixing 200mm dia.PVC water gutter to fixing the end of slopped roof with MS clamps as per the direction of departmental officers at site.

OD34832/2022-2023:Supplying and fixing 110mm PVC floor trap best quality

50.17.1.5:Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

OD34833/2022-2023:Supplying fixing 15 mm dia or nearest size C.P short body tap.

OD34834/2022-2023:Supplying and fixing ready made design cutting for eave board to roofing

OD34835/2022-2023:Apoxy based water proofing treatment for toilet (without dismantling toilet floor and wall tile)

14.1.1:Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 meters lead:With cement mortar 1:4 ( 1 cement : fine sand)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

50.18.7.4.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall

50.18.7.3.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm2 - Internal work - Exposed on wall

13.21:Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

OD34836/2022-2023:null Engaging Scavenger

OD34837/2022-2023: null Engaging Carpenter 2nd class

14.72X:Scaffolding

OD34838/2022-2023:Supplying fixing 15 mm dia or nearest size C.P long body tap.

OD34839/2022-2023:Engaging wood cutter

OD34840/2022-2023:Engaging coolie

OD34841/2022-2023:Fitter (grade1)

4.1.4:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 )1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size)

15.57:Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge

15.17.2:Dismantling steel work in single sections including dismembering and stacking within 50 metes lead in:Channels, angles, tees and flats

50.14.1.1:Removing and refixing door shutters after necessary repairs for easy opening and closing etc complete as per the direction of site Engineer-in-charge.

50.14.1.2:Removing and refixing window shutters after necessary repairs for easy opening and closing etc complete as per the direction of site Engineer-in-charge

50.18.7.4.2:Providing and fixing PVC, pipes fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - internal work- Exposed on wall

50.18.7.5.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 6Kgf/cm2 - Internal work - Exposed on wall

50.18.7.6.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

50.18.8.5.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 40 mm pipe 6Kgf/cm2

50.18.8.6.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.7.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

50.18.9.8.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

9.141:Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (±0.2mm), made out of single piece extruded PVC profile, with mitred cut joints and with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm, including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8x100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer-in--charge.

9.142.1:35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded solid PVC ( ±0.2 mm) thick, having styles & rails (except lock rail ) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinges side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm x 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm x 100 mm of cross section size 35 mm x 17 mm s 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in-charge.Non decorative finish (matt finish)

17.7.3:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

17.2.1:Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

8.2.2.2:Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

OD41337/2022-2023:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating50 micron)

OD89829/2022-2023:Providing and fixing 4mm thick ACP sheet fixed in aluminium partition frames with C.P brass/stainless steel screws ,EPDM rubber/neoprene gasket etc complete as per directions of Engineer -in charge.

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

OD41357/2022-2023:Supplying and fixing 200mm or nearest size SS aldrop

OD41358/2022-2023:Supplying and fixing 15mm CP piller tap as per the direction of engineering incharge.

OD41359/2022-2023:Providing and fixing stainless steel soap dish of single tray of good quality etc. complete.

18.7.2:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal outer dia pipes

18.7.3:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes

18.7.4:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes

OD42886/2022-2023:supplying and fixing 15mm CP angle cock best quality as per the direction of engineering incharge

OD42885/2022-2023:Providing and laying 80 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge

50.18.9.20.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

50.18.9.21.10:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x63 mm dia Reducer

OD93657/2022-2023:Flooring with Designer tiles for external use in CM 1:3 and pointing with coloured cement including all cost of materials labour charges conveyance etc. complete

OD95081/2022-2023:Providing and fixing 3 layer PP-R ( poly propylene Random co- polymer) pipes SDR 7.4 U V stabilized and anti microbial fusion welded,having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings. i/c fixing the pipe with clamps at 1.00 m spacing .This includes testing of joints complete as per direction of Engineer- in-Charge. External workPN 10 75 mm dia

OD99860/2022-2023:Providing and fixing 3 layer PP-R (Poly propylene random copolymer)pipes SDR 7.4, U V stabilized & anti -microbial fusion welded ,having thermal stability for hot & cold water supply, including all PP-R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 spacing.This includes testing of joints complete as per direction of Engineer in charge .Internal work -exposed on wall. PN 10 63 mm Dia .

OD99912/2022-2023:Providing and fixing 3 layer PP-R (Poly propylene Random copolymer ) pipes SDR 7.4, U V stabilized & anti -microbial fusion welded ,having thermal stabilityfor hot &cold water supply,including all PP-R plain & brass threaded polypropylene random fittings,i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall .PN 10 50 mm dia

APPENDIX-B -MCTCR-Development-setting up of Multidisciplinary research unit

OD34814/2022-2023:SAMPLE STORAGE/BIO BANKING-Supply of Wall Bench of length 3000mm and 750 mm wide using 16mm thick Trespa worktop Complete with; • one number 500mm wide under bench cabinet with one adjustable shelf and one door with lock • one number 500mm wide under bench cabinet with one drawer, one adjustable shelf and one door with lock • one number 600mm wide under bench sink cabinet • including front+ back frame, middle frame, side frame and knee space panel • one number TOF Italy/eqivalent make single cold water standout • one number 450x350 mm size polypropylene sink • two number of 15 Amp/220 Volt double electrical pedestal box Size: 3000x750x900mm(H)- Specifications Of Wall Bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black color uniformly though out the surface. Test reports from the manufacturer will be provided. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1) mm toprotect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Knee space panel: It shall be made of 9 mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Water fittings: Fittings shall be made of brass (UNI 5705 -65) and should have an epoxide covering in White color. Fittings shall be manufactured as per modern technologies & comply to DIN 12920 standards for the best performance. Polypropylene sink: It shall be of Polypropylene, molded as one piece. The dimensions of the sink are 45x35x20cm (depth). The sink should not have any sharp corners inside. Sink color shall be black All sinks shall be supplied with bottle trap. Supply of Tall storage cabinet 900mm wide with panel doors and lock Size: 900x400x1800mm(H) Specification Tall Storage Cabinet: Door Front: Door is made of 18 mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius or above. The Melamine Laminate confirms to BS, NEMA & BIS Standards. The doors are provided with chromium plated “D” shaped handle. Where specified good quality locks and keys will be provided for cabinets. Tall Storage Body: Body is made of 18mm thick BWP plywood laminated with 0.6mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. Top and Bottom panels are made of 18mm thick furniture grade plywood with 0.6mm thick melamine on both sides and the edges with tape edging. Back wall is made of 4mm thick BWP Melamine laminated plywood. Provided with Adjustable and fixed shelves both made of 18mm thick BWP plywood laminated with 0.6mm thick melamine on both sides edge with tape edging. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections.

OD34815/2022-2023: SAMPLE PREPARATION-Supply of L-shape bench of length 3500mm and 2500mm (750 mm wide) with 16mm thick Trespa worktop Complete with; ? One number 500mm wide under bench cabinet with one adjustable shelf and one door with lock. ? two number 500mm wide under bench cabinet with 1 drawer, one adjustable shelf and one door with lock ? one number 600mm wide under bench sink cabinet ? including front+ back frame, middle frame, side frame corner support , filler panel and knee space panel ? one number TOF Italy/equivalent make single cold water standout ? one number 450x350 mm size polypropylene sink ? three number of 15 Amp/220 Volt double electrical pedestal box- Size: 3500+2500x750x900mm(H) Specifications Of Wall Bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Water fittings: Fittings shall be made of brass (UNI 5705 -65) and should have an epoxide covering in White color. Fittings shall be manufactured as per modern technologies & comply to DIN 12920 standards for the best performance. Polypropylene sink: It shall be of Polypropylene, molded as one piece. The dimensions of the sink are 45x35x20cm (depth). The sink should not have any sharp corners inside. Sink color shall be black All sinks shall be supplied with bottle trap. Supply of Static Pass box- Size: 570x530x590mm Specifications Static Pass Box: Pass box shall be made of 1.2 mm thick S.S304 Grade material with seamless welded joints. Pass box is equipped with two doors and both doors are operated electronically. And only one door should be opened at one time. The UV Light installed in the chamber will ON while both doors are closed. UV light has to be automatically turned off when opening either of the doors. There shall be indicators on both sides of the unit, so that door open/close status can be monitored from both sides. Doors shall be with double view glass. Inner size of the unit is 450x450x450 mm and outer size is 570x530x590mm.

OD34816/2022-2023: COLD ROOM-Supply of SS Table of 1200mm length 600wide with Stainless steel worktop and one SS shelf at the middle. Size: 1200x600x900mm(H) Specifications of SS Table: Stainless steel worktop: Stainless steel worktops fabricated from 1.2 mm thick type 304 series stainless steel. Surfaces are integrally formed with all seams fully welded with stainless steel fillers, ground smooth, and blended to mill finish. Finished bench thickness is 20(±1) mm. The inside of the worktop is made of 18 mm thick plywood to strengthen the worktop. Support Frame Work : The worktops will be supported by the frames. These frames will be made of 304 stainless steel 30x30 mm square tube sections. Worktops will be supported by this frame work. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. The worktops will be supported by the frames. These frames will be made of 2mm thickness 30x30 mm square tube sections which are welded. Worktops will be supported by this frame work. The frame work will be de–greased and epoxy powder coated with the thickness of min. 80 microns for smooth finish and protection. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame.

OD34817/2022-2023:DNA SEQUENCING AND NGS ROOM-Supply of Wall Bench of length 3500mm and 750 mm wide using 16mm thick Trespa worktop Complete with; ? one number 600mm wide under bench cabinet with one drawer, one adjustable shelf and one door with lock ? including front+ back frame, middle frame, side frame, corner support and knee space panel ? one number 600mm wide under bench sink cabinet ? one number TOF Italy /equivalent make single cold water standout ? one number 450x350 mm size polypropylene sink ? two number of 15 Amp/220 Volt double electrical pedestal box Size: 3500x750x900mm(H) Specifications of wall bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lippingof 3(± 1) mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Knee space panel: It shall be made of 9 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Water fittings: Fittings shall be made of brass (UNI 5705 -65) and should have an epoxide covering in White color. Fittings shall be manufactured as per modern technologies & comply to DIN 12920 standards for the best performance. Polypropylene sink: It shall be of Polypropylene, molded as one piece. The dimensions of the sink are 45x35x20cm (depth). The sink should not have any sharp corners inside. Sink color shall be black All sinks shall be supplied with bottle trap. -Supply of Wall Bench of length 6350mm and 750 mm wide using 16mm thick Trespa worktop Complete with; ? one number 600mm wide under bench cabinet with one adjustable shelf and one door with lock ? one number of 1200mm wide combined cabinet with two doors one drawer, two adjustable shelves with lock ? one number 600mm wide under bench cabinet with one drawer, one adjustable shelf and one door with lock ? one number of 1200mm wide combined cabinet with one drawer two doors, two adjustable shelves with lock ? including front+ back frame, middle frame, side frame, filler panel and knee space panel ? Three number of 15 Amp/220 Volt double electrical pedestal box. Size: 6350x750x900mm(H) Specifications of wall bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Knee space panel: It shall be made of 9 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1)mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. 8 1 Lo t Supply of Tall Storage Cabinet 900mm wide with panel doors and lock Size: 900x400x1800mm(H) Specification Tall Storage Cabinet:- Door Front: Door is made of 18 mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius or above. The Melamine Laminate confirms to BS, NEMA & BIS Standards. The doors are provided with brush finish stainless steel “D” shaped handle. Where specified good quality locks and keys will be provided for cabinets. Tall Storage Body: Body is made of 18mm thick BWP plywood laminated with 0.6mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. Top and Bottom panels are made of 18mm thick furniture grade plywood with 0.6mm thick melamine on both sides and the edges with tape edging. Back wall is made of 4mm thick BWP Melamine laminated plywood. Provided with Adjustable and fixed shelves both made of 18mm thick BWP plywood laminated with 0.6mm thick melamine on both sides edge with tape edging. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections.

OD34818/2022-2023: PRE PCR-Supply of Wall Bench of length 3500mm and 750 mm wide using 16mm thick Trespa worktop Complete with; • two number 600mm wide under bench cabinet with one adjustable shelf and one door with lock • one number 600mm wide under bench cabinet with one drawer, one adjustable shelf and one door with lock • including front+ back frame, middle frame, side frame and knee space panel • two number of 15 Amp/220 Volt double electrical pedestal box -Size: 3500x750x900mm(H) Specifications of wall bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1) mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Knee space panel: It shall be made of 9 mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. -Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. -Supply of Static Pass Box Size: 570x530x590mm(H) Specifications Static Pass Box: Pass box shall be made of 1.2 mm thick S.S304 Grade material with seamless welded joints. Pass box is equipped with two doors and both doors are operated electronically. And only one door should be opened at one time. The UV Light installed in the chamber will ON while both doors are closed. UV light has to be automatically turned off when opening either of the doors. There shall be indicators on both sides of the unit, so that door open/close status can be monitored from both sides. Doors shall be with double view glass. Inner size of the unit is 450 x 450 x 450 mm and outer size is 570 x 530 x 590 mm.

OD34819/2022-2023: POST PCR-Supply of L Shape Bench of length 3500+1500mm and 750 mm wide using 16mm thick Trespa worktop Complete with; • two number 600mm wide under bench cabinet with one adjustable shelf and one door with lock • one number 600mm wide under bench cabinet with one drawer, one adjustable shelf and one door with lock • including front+ back frame, middle frame, side frame,corner support and knee space panel • three number of 15 Amp/220 Volt double electrical pedestal box Size: 3500+1550x750x900mm(H) Specifications Of Wall Bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1)mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Knee space panel: It shall be made of 9 mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. -Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified.

OD34820/2022-2023: PCR-Supply of Wall Bench of length 2300mm and 750 mm wide using 16mm thick Trespa worktop Complete with; • one number 600mm wide under bench cabinet one adjustable shelf and one door with lock • one number 600mm wide under bench cabinet with one drawer, one adjustable shelf and one door with lock • including front+ back frame, middle frame, side frame and knee space panel • two number of 15 Amp/220 Volt double electrical pedestal box Size: 2300x750x900mm(h) Specifications of wall bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1)mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. -Knee space panel: It shall be made of 9mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Supply of Bio Safety Cabinet- Size: 1350x700x2020mm(H) Specifications Bio Safety Cabinet: The primary purpose of a BSC is to serve inward airflow for personnel protection, downward HEPA filtered laminar airflow for product protection, and HEPA filtered exhausted air for environmental protection. Blowers are mounted on the cabinet to draw directional mass airflow around a user, into the air grille, the air is then drawn underneath the work surface and back up to the top of the cabinet where it passes through the HEPA filters. This column of HEPA filtered air is re-circulated, over products and processes to prevent contamination. Features; Display of ON/0FF Control and Status Indication of Blower, UV Lamp & Led Light for enhanced user interface. UV Lamp installed which helps in surface decontamination and sterilizing the workspace. Measures the air velocity, detects any change that occurs and alerts the user through audio and visual alarms. Motorized Glass Sash Assembly Movement. Angled front Sash: Enables easy access to the filter zone and interior for maintenance. HEPA filter: Two HEPA filters with efficiency of 99.9% at 0.3µm Material: 304 stainless steel in work area. Cold rolled steel with epoxy coating on the body Cabinet provided with support frames with leveling jacks. External Dimension of chamber: - 1350 x 700 x 1355 mm (h) Internal dimension chamber: -1210 x 600 x 700 mm (h) External dimension with base stand: -1350 x 700 x 2020mm (h) -Supply of Static Pass Box Size: 570x530x590mm(H) Specifications Static Pass Box: Pass box shall be made of 1.2 mm thick S.S304 Grade material with seamless welded joints. Pass box is equipped with two doors and both doors are operated electronically. And only one door should be opened at one time. The UV Light installed in the chamber will ON while both doors are closed. UV light has to be automatically turned off when opening either of the doors. There shall be indicators on both sides of the unit, so that door open/close status can be monitored from both sides. Doors shall be with double view glass. Inner size of the unit is 450 x 450 x 450 mm and outer size is 570 x 530 x 590 mm.

OD34821/2022-2023: WASH AREA-Supply of Wall Bench of length 2000mm and 750 mm wide using 16mm thick Trespa worktop Complete with; • one number 600mm wide under bench cabinet with one adjustable shelf and one door with lock • one number 1320mm wide under bench sink cabinet • including front+ back frame, middle frame filler panel and side frame • one number polypropylene drip rack with 27 pegs Size:400x550 mm(LxH) • two number TOF Italy/equivalent make single cold water standout • two number 450x350 mm size polypropylene sink -Size: 2000x750x900mm(H) Specifications Of Wall Bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. -Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Filler panel: It shall be made of 18 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1)mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Polypropylene sink: It shall be of Polypropylene, molded as one piece. The dimensions of the sink are 45x35x20cm(depth). The sink should not have any sharp corners inside. Sink color shall be black All sinks shall be supplied with bottle trap. Drip Rack: Drip rack will be manufactured in chemical resistant material such as polypropylene for drying glass ware. Pegs will be manufactured from polypropylene material and will be inserted in polypropylene flat sheet. Drip racks will have a drip channel or a tray at the bottom which will drain the water through the rubber tube connected to the nozzle fitted to the drip channel. Wherever the back portion of the drip rack is exposed, it will be fully covered with 3 mm thick compact laminate. Water fittings: Fittings shall be made of brass (UNI 5705 -65) and should have an epoxide covering in White color. Fittings shall be manufactured as per modern technologies & comply to DIN 12920 standards for the best performance.

OD34822/2022-2023: HOD-Supply of L Shape Bench of length 2000mm 750 mm wide and 1000mm long 600mm wide using 18mm thick Melamine Laminated Plywood worktop. Complete with; • one number 600mm wide under bench cabinet with one drawer, one adjustable shelf and one door with lock • one number of cable grommet, keyboard tray and CPU hanger • including filler panel and knee space panel • one number of 15 Amp/220 Volt double electrical sockets and one data socket -Size: 2000+1000x750x750mm(H) (Worktop height is 750mm height from F.F.L) Specifications Of L Shape Bench -High pressure melamine laminate worktop: Melamine Laminated Ply wood work tops are made from 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination is done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC edging/lipping not less than 3 mm to protect from impacts, moisture and insects. The edging/lipping is machine applied with hot melt glue at a temperature of 205 degree Celsius. All worktops will have 80mm glued back splash for wall benches, of the same material. The Melamine Laminate confirm to BS, NEMA & BIS Standards -Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1)mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Tables with Floor Mounted Under Bench Cabinets: For the floor standing or plinth mounted cabinets, the work top will be supported by the cabinets which rest on the floor without any additional support of any steel frameworks. Panel supports are provided if additional supports are needed. Knee space panel: It shall be made of 9mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lippingof 3(± 1)mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Electrical fittings: Double sockets and switches. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. Switches will be Piano type unless otherwise specified. Cable Gromet: The cable gromet on the work surface will be flexible plastic component for easy and safe passage of wires. CPU Holder: It will be made of steel, and used to Store C.P.U. under the table and saves space and it has a safe load caring capacity of 20kg. Soft anti-vibration pads provided. No tools needed for adjusting height and width range. Width adjustment from 145 mm to 225 mm. Height adjustment from 310 mm to 530 mm. Key Board Tray: Ergonomic Key Board trays will be molded and made of ABS material. Supply of Tall Storage Cabinet900mm wide with panel doors and lock Size: 900x400x1800mm Specification Tall Storage Cabinet: Door Front: Door is made of 18 mm BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped with PVC lipping of 3(± 1)mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius or above. The Melamine Laminate confirms to BS, NEMA & BIS Standards. The doors are provided with brush finish stainless steel “D” shaped handle. Where specified good quality locks and keys will be provided for cabinets. Tall Storage Body: Body is made of 18mm thick BWP plywood laminated with 0.6mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. Top and Bottom panels are made of 18mm thick furniture grade plywood with 0.6mm thick melamine on both sides and the edges with tape edging. Back wall is made of 4mm thick BWP Melamine laminated plywood. Provided with Adjustable and fixed shelves both made of 18mm thick BWP plywood laminated with 0.6mm thick melamine on both sides edge with tape edging. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections.

OD34823/2022-2023: RECEPTION/SAMPLE COLLECTION-Supply of L Shape Bench of length 2000mm 750 mm wide+2350mm long 600mm wide using 13mm thick compact Laminate top with 300mm wide counter top(one side)of18mm thick melamine laminated plywood. Complete with; • one number 900mm wide under bench cabinet with two drawer one adjustable shelf and two doors with lock • one number of cable grommet and cpu hanger • including corner support filler panel and knee space panel • one number of 15 Amp/220 Volt double electrical socket and one data socket -Size: 2000x750x750mm+2350x600x750mm(H) (Worktop height is 750mm height from F.F.L) Specifications Of L Shape Bench: Compact laminate work top: It will be 13 mm thick panel based on thermosetting resins, homogeneously reinforced with cellulose fibers and manufactured under high pressure and temperature. Compact laminate panels have an integrated, decorative structure based on modified melamine impregnated decorative paper. All worktops will have 80mm glued back splash for wall benches, of the same material. The Compact Laminate confirms to BS, NEMA & BIS Standards. High pressure melamine laminate worktop: Melamine Laminated Ply wood counter top made from 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination is done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC edging/lipping of 3(± 1)mmto protect from impacts, moisture and insects. The edging/lipping is machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate confirm to BS, NEMA & BIS Standards Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1)mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. -Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Tables with Floor Mounted Under Bench Cabinets: For the floor standing or plinth mounted cabinets, the work top will be supported by the cabinets which rest on the floor without any additional support of any steel frameworks. Panel supports are provided if additional supports are needed. Knee space panel: It shall be made of 9mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1)mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. -Electrical fittings: Double sockets and switches. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. Switches will be Piano type unless otherwise specified. -Cable Gromet: The cable gromet on the work surface will be flexible plastic component for easy and safe passage of wires. -CPU Holder: It will be made of steel, and used to Store C.P.U. under the table and saves space and it has a safe load caring capacity of 20kg. Soft anti-vibration pads provided. No tools needed for adjusting height and width range. Width adjustment from 145 mm to 225 mm. Height adjustment from 310 mm to 530 mm.

OD34824/2022-2023: CHANGE AREA-Supply of Coat Hanging Storage Cabinet With Shoe Rack Size:900x500x1800mm(H) -Specification Coat Hanging Storage Cabinet With Shoe Rack: The coat hanging cabinets shall be made of Thickness 18mm (±1) mm Core Material (BWP – Boiled Water Proof) plywood. Finish – High quality HPL (High pressure Melamine laminate) of 0.6mm hot pressed on both the sides. The exposed edges will be sealed with minimum 3mm thick high quality PVC edges. For strong bonding and durability, the lamination and edging will be machine pressed at high temperature and pressure. • The doors will be provided with brush finish stainless steel “D” shaped handle. • Provided with shelves made of 18±1mm thick BWP plywood laminated with 0.6mm thick melamine on both sides edge with tape edging. Provision for keeping coats and shoe will be provided. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections.

OD34825/2022-2023: AUTOCLAVE AND STERILISING AREA/PURIFYING AREA-Supply of Work Table 1200mm length 600wide with granite worktop. -Size: 1200x600x900mm(H) Specifications of Work Table: Granite worktop: The table worktops where specified will be of at least 18(±1) mm thick Jet Black color Granite (min 7 to 8 Kg per Sq. Ft) of even surface, fine to close-grained, with equi-granular crystalline texture, without any undue specks, or cracks. The edges of the granite tops will be half round molded and polished. Support Frame Work: The worktops will be supported by the frames. These frames will be made of 2mm thickness 30 x 30 mm square tube sections which are welded. Worktops will be supported by this frame work. The frame work will be de–greased and epoxy powder coated with the thickness of min. 80 microns for smooth finish and protection. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame.

IJAS C

K V SARATHKUMAR

Bidder Name

K V SARATHKUMAR

IJAS C

AHAMMAD KABEER P H