PROVN OF BATHROOM BLOCK WITH OVERHEAD TANK NEAR BLDG NO T-23 AT AMARIBARI LOC OF 16 MED REGT AND OTHER REV/MINOR WORKS AT AGE CHARDUAR AREA UNDER GE (N) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in loose/soft soil etc complete all as specified and directed.

Removal of excavated materials not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting points etc complete all as specified and directed.

M & L for hard core broken stone or builders of gauge not exceeding 63mm, deposited, spread and leveled in layer not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L PCC 1:4:8 type D-2 100mm thick with using 40mm graded stone aggregate as in pavement of hardstanding complete all as specified and directed.

Materials and labour for brick work with locally available best quality sub class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for Cement concrete type B-2, 1:2:4 in floors 75mm thick over sub base using 20mm graded aggregate finished even and smooth without using extra cement complete all as specified and directed.

Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

Surface dressing n.exc 15cm deep soft/loose soil complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregatein plinth protection or similar places laid in alternate way surface finished even and fair wthout using extra cement complete all as specified and directed.

M&L for use and waste of form work to sides of concrete foundation, footing, bases of columns, rafts and raft beams, sides and soffits of foundation and plinth beams and similar work,vertical or to the batter of rough finished surface complete all as specified and directed.

Use and waste formwork to the sides of square columns, pillars etc of rough finished surface complete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams,lintel,cantilevers,shelves etc including support of rough finished surface of concrete flat complete all as specified and directed

S&F TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F TMT bars 6 to 8mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

S & F mild steel TMT bar 5 to 10 mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

M&L RCC typ B-1(1:2:4) nominal mix using 20 mm graded stone aggregate as in column footing including raft footings, foundation, plinth beam, bases of column etc complete all as specified and directed.

M&L RCC type B-1(1:2:4) nominal mix using 20 mm graded stone aggregate as in columns, pillars etc complete all as specified and directed.

M&L RCC (1:2:4) nominal mix using 20 mm graded stone aggregate as in P/beam, roof beam, cantilevers, lintel beam, etc complete all as specified and directed.

M & L for plain cement concrete (1:4:8) Type D-2 using 40mm graded aggregate in foundations filling and mass concrete complete all as specified and directed.

M&L for sand filling under floor or below paver blocks incl. watering and consolidation.

M&L for 75 mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base under floor

M&L for 40 mm thick cement concrete type B-1, 1:2:4 (20 mm graded aggregate) to receive the top layer of tiles

M & L brick work with subclass ‘B’ bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6

M&L for brickwork with sub class’B’ bricks, straight or curved on plan exc 6m mean radius in half brick work built in CM 1:4.

M&L for 20mm thick in cement mortar 1:2 damp proof course to horizontal or vertical surfaces with WPC including necessary formwork, as directed

M&L 15mm thick plastering on fair faces of bricks or cone surfaces finished even and smooth w/o using extra cement in CM 1:4 complete all as specified and as directed.

M&L for rendering 10 mm thick plastering on fair faces of brickwork surfaces in cement mortar (1:6) making smooth and even surfaces without using extra cement complete all as specified and as directed.

M&L for providing precast cement concrete type B1 1:2:4 using 20mm graded aggregate in door cills, lintels bressumers, copings and setting in cement mortar 1:4 complete with joints to match

M&L screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:4.

M&L for rendering 10 mm thick screed bed on fair faces of brickwork surfaces in CM 1:3 to receive wall finishes.

M&L coloured glazed ceramic tiles 200x 300x7 mm thick, in vertical surfaces, skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as directed.

S & F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall,fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F Mild steel screw bolts(15mm dia) (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified and directed.

S & F Fe 410-W(Gde-E250) roof trusses (framed) cross beams, hip and jack rafters; purlins where connected to common rafters fixed with angle cleats or other connectings plates

M & L Anodised aluminium window or ventilator (sliding type) shutters /fixed type without sash bars necessary joining cleats , glazing clips ,rubber neoprene packing handles 2 Nos in each doors hinges anodised aluminium snap beading, screws,roller bearing etc.complete all as specified.

S&F anodised aluminium frame door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

M&L including preparing of new plastered surface and applying two coats cement base paints on walls.

S & F 1000 litre capacity ,rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) in position all specified in SSR Part –I

M & L Ball valves (20 mm) high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms/ 50mm-1240 gms)

S&F 20 mm dia gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F Vitreous China wash basin, white, flat back, size 550x400mm (flat back or angle back type) including brackets, cutting for and pinning 'in brackets waste coupling, waste pipe, grating complete

S&F Vitreous china squatting pan, Orissa' pattern size 580x440 mm white with integral foot rests including connection to drain pipes and to flushing pipes antisy phonage pipe etc excluding flushing cistern incl flush pipe complete as as specified and directed

S&F Vitreous china wash down water closet pan, (pedestal pattern), whiten including connection to drain pipes and to flushing pipes antisy phonage pipe etc excluding flushing cistern incl flush pipe, jet and seat cover complete as as specified and directed

S&F vitreous china urinal,bowl type size of 465x335x265mm (back or corner wall type) complete incl providing and fixing plugs beding urinal against wall in cm 1:2 security urinal plug with and incl 60mm long brass screws pointing around urinal back in cement fixing automatically flushing cistern with bracket, flush pipes grating and union for discharge pipe complete.

S&F Vitreous china partition white of size 310 x 779 mm

S & F 15mm bore bib taps, chromium plated cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S & F 15mm bore stop valves/angle cock, fancy type, chromium plated cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S & F brass chromium plated tubular towel rail 20mm dia

S & F brass chromium plated shower rose 125mm size

S&F PVC connections 15mm size with PTMT nuts of length 300/450mm

S & F 10 litres PVC Syphonic action type, Flushing cistern, high level, with inlet, ball valve, float chain and pull incl flush pipe32mm dia and brackets complete.

S&F 100mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F 100mm grating doom 100mm dia of PTMT

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

M&L for PCC 1:3:6 type C1 as in concrete bed to drain pipe incl packing under haunching against the sides of pipes after are laid and tested for 110mm dia pipe.

S & F 75mm bore PVC ( SWR) pipes single socketed ,in any length with rubber ring joints, fixed to wall.

S & F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S & F PVC (SWR) bends of radius 110mm bore.

S & F PVC (SWR) junction single,(Single T) equal or unequal of radius 75mm bore.

S & F PVC (SWR) bends of radius 75mm bore.

S & F 110mm bore PVC ( SWR) pipes single socketed ,in any length with rubber ring joints, fixed to wall.

S & F 110MM PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S & F PVC (SWR) vent cowl 110mm bore.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing.

M&L for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plaincolour PVC© channel PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock and bottom rail on either side as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded. Sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing.

S&F Butt hinges, 100mm long extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed

S&F as Aluminium anodised barrel tower bolts of extruded section and fixed as 200mm long

S&F as Aluminium handles cast type anodised 150mm long and fixed as complete

Cutting existing steel tubing for alterations or additions( Each cut measured) necessarily done in position without taking down

Returning, filling in, including spreading leveling watering and well ramming in layers n,exc 25 cm thick in soft /loose soil for sewage pipe line /manhole and cleaning the site.

M & L for plain cement concrete type-C2 1:3:6 (40mm garaded agg.) in surface channel and drains

M&L extra for forming fair finished drain or channel any girth in cement concrete using extra cement including forms, moulds mitred/stopped ends etc

M&L for plain cement concrete type B-1, 1:2:4 using 20mm graded aggregatein kerbs , copings rounded or chamfered on edges , finishing top surfce even and smooth without using extra cement as in path side strips incl of form work of side complete all as specified and directed.

M&L for Coloured Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement slurry and no pigment complete all as specified and directed.

Excavating in trenches, n exc1.5 m wide and n exc 1.5 m indepth; for foundation, etc. or for shafts,wells, cesspits,manholes, pier holes, etc. nexc 10 sq m on plan and n exc1.5 m in depth and getting out complete all as specified and directed

Ditto as per item no 78 above but exc 1.5m in depth

M&L PCC 1:2:4 type B2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified & directed

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed

Rendering 15mm thick on fair faces of brick work or concrete surfaces cement plaster 1:4 with WPC to be finished even and smooth (without extra cement) complete all as specified & directed

Supply only intergral WPC complete all as specified & directed

M&L Precast cement concrete 1:2:4 type B1 (20mm agg) for cover Slabs (for man holes etc) setting in cement mortar(1:4) as specified and directed

S&F 75mm PVC(SWR) vent cowl complete all as specified and directed

S&F 110mm bore PVC(SWR) junction single (single T) equal or unequal complete all as specified and directed

M&L 1:3:6 type C2 cement Concrete bed to drain pipe 100mm including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed

M&L Loose filling with Broken bricks s of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and directed

Excavation in post holes (or similar holes) each n.exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm in soft loose soil.

S&F angle iron as in posts and struts in fencing incl cutting top to shape as directed, drilling holes, notching for wire etc and flat iron fillets for securing chain link fencing and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

Supply only chain link fencing link MS galvanised fencing of mesh size 80mmx80mm,wire gauge 8 to 12 mm, wire dia 4.06 mm

Fixing only chain link fencing, including line wires, any mesh and size to any type of standards, rails, straining bolts, etc including provision of binding wire

M&L flat iron (40X60mm) straps for securing corner posts and chain link fencing all as directed.

S&F mild steel screw bolts 10 mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut n.nxc 5 cms long.

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:4) finished even & smooth (without using extra lime or cement)

M&L for applying two coat of cement based paint paint on new surface including preparation of surface complete all as specified and directed.Priming plastered and other surfaces with alkali resistant priming paint complete all as directed.

Removing excavated materials (soil) exc 250m but n.exc 500m and depositing where directed at a level n.exc 1.5m above the starting point.

S&F Fibre Reinforced Plastic plain sheet for bdy wall fixed with angle iron frame work all as specified and as directed.

Materials and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in foundation,& Plinth beam

Materials and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in Columns

Materials and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as roof beam beam,GB,Lintel beam

M&L for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like using cement concrete M-25 (20mm graded aggregates) complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick complete all as specified and directed.

Material and labour for Polythene film, black, 50micron laid infloors

M&L for cement concrete 25mm thick type B-0, 1:2:4 (12.50 mm graded aggregate)

M/L 7 to 8mm thick non skid coloured ceramic tilesarea of each tile exceeding 0.11 sqm but notexceeding 0.18 sqm as in floors over and incl. screed bed of 15mm CM (1:4) & jointed neat cement slurry & pointed with coloured cement to match with the tiles.

M & L 300 x 200 x 6mm thick coloured tiles glazed ceramic in vertical surfaces dados etc set and jointed in neat cement slurry and pointed in white cement over & incl.10 mm thick screed bed in CM 1:4.

Materials and labour for brick work with sub class 'B' bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:4) complete all as specified and directed.

S & F 1.60mm thick MS sheet eaves 250mm wide as in eaves board complete all as directed

Plain Cement Concrete Type B1,Nominal mix conc M15 1:2:4 (using 20 mm graded granite stone aggregate) to fix steel stair case complete all as specified and as directed.

M&L preparing new steel surface of any description not otherwise described for over 10 cm width or girth and applying two coat of synthetic ennamel paint with red oxide primer complete all as specified and directed.

Material and labour for rendering 15mm thick cement plaster in cement mortar (1:6) on unfair faces of brickworks complete all as specified and directed.

M&L for rendering 5mm thick on ceiling in CM1:4

M & L preparation of new plaster surface of celing etc and applying three coats of white washing complete all as specified and directed.

M & L preparation of new plaster surface of wall etc and applying three coats of white washing complete all as specified and directed.

M & L non skid ceramic coloured/designer tiles 7 to 8 mm thick (square rectangular ) area of each tile exc 0.06 sqm but nexc 0.11 sqm, laid over & including 15 mm thick screed bed or bedding layers of mortar in cm (1:6) for laying floor finishes all as specified in floors etc set and jointed in neat cement slurry and pointed in white cement to match the shade of tiles

M&L coloured, digital glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed (Make Johnson/Kajaria)

M&L coloured, digital glazed ceramic tiles as in floor 600x600x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed (Make Johnson/Kajaria)

All as per item No-118.00 here-in-before but in skirting/dado but over 10 mm thick rendering over CM 1:4

S&F Galvanised corrugated mild steel sheeting with two corrugation side lap, with coach screw & washers, in roofs, walls etc with grade of zinc coating 275 of 0.63mm thick

S&F Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip & straight flashings (length & girth as fixed) with grade of zinc coating 275 of 1.00mm thick

S & F anodised GI snap grid (Size of grid 605mmx605mm ) frame work for false ceiling including GI wire 4mm thick as a suspender for GI snap grid framing all as specified

S&F 4 mm thick Non asbestos fibre cement building board decorative type( e-board) fixed in aluminium snap grid frame work with screws.

M & L rendering 5 mm thick in cement plaster in cement mortar (1:4) mixed with integral water proofing compound @3%by wt of cement over 10 mm thick backing coat in cm (1:4) on fair faces of brick work or concrete surface complete all as specified and directed. Note : water proofing compound shall be measured and paid separately).

supplied only integral waterproofing liquid

M&L for 75 mm 1:3:6 type C2 ( using 40 mm graded stone aggregate) as plinth protection/paving finish even and smooth without using extra cement.

M & L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'B'

M & L for preparation of new plaster surface of walls etc and applying two coats of acrylic washable distemper over 1 mm thick wall care putty in two coats over a coat of primer (smooth bodied opaque finish surface) complete all as specified and directed.

M&L for 2 nd class hard wood scantling wrought finished in any position over and 40 sq. cm & over in section,complete all as specified and directed.

M & L preparation of old surface & applying one coat of synthetic enamel paint to wooden surfaces exc 10 cm girth complete all as specified and directed.

S&F 1st class softwood Plain, solid, straight, chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints.

S&F 30 mm thick Flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides

S&F 1st class softwood 35mm thick Glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut & mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); to chowkats

S&F 1st class softwood 30mm thick Glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut & mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); to chowkats

S&F Butt hinges 100mm size, medium weight, cold rolled mild steel.

S/F 150mm long aluminium anodised barrel tower bolt of extruded section.

S&F aluminium alloy sliding door bolt 300mm long, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F Sheet glass 5.5mm thick, ordinary quality & glazing with oil putty in square exc 0.5 sq.m in each pane complete all as specified and as directed

S&F in repair CP tubular towel rail 600 mm long all as directed .

S&F cast iron body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width & of weight between 61 to 80kg.

Supplying and laying of 16 mm bore outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified

Supplying and laying of 20 mm bore outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified

Cutting chases, pinning in, making good to facings where required and pointing in CM (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting exc 10 cm but not exc 20 cm girth in brick wall

M&L 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

E/M PORTION

M&L point wiring for light point/fan/bell point controlled by one, one way switch/bell push using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated sheathed FRLS cables in and including casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed recessed boxes confirming to IS-14772-20000 for mounting of switches/sockets/regulators/bell push etc and1.5 Sq mm nominal cross sectional area multistranded copper conductor PVC insulated sheathed earth wire and connecting to earth dolly by means of screws, washers etc. complete.

M&L wiring for one 3 pin socket outlet 5 amps on independent board using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated sheathed FRLS cables in and including casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed recessed boxes confirming to IS-14772-20000 for mounting of switches/sockets etc and1.5 Sq mm nominal cross sectional area multistranded copper conductor PVC insulated sheathed earth wire and connecting to earth dolly by means of screws, washers etc. complete all as specified.

Ditto all as above but for 5 Amps socket point on same board.

M&L wiring for one 3 pin socket outlet 15 amps on independent board using 2.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated sheathed FR LSH cables in and including casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed recessed boxes confirming to IS-14772-20000 for mounting of switches/sockets etc and 2.5 Sq mm nominal cross sectional area multistranded copper conductor PVC insulated sheathed earth wire and connecting to earth dolly by means of screws, washers etc. complete.

S&F Polycarbonate Switch piano flush type, SP, 6 Amps, one way complete.

S&F Polycarbonate socket out let 2 in 1 socket 5 pin, (6 Amps) flush type controlled by one switch, complete.

S&F Polycarbonate switch socket out let 2 in 1 socket 5 pin, 5&15 amps flush type controlled by one 15 Amps switch, complete.

Supply and fix in replacement wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver lamp type 22 watt 6000K 4 feet.

S&F lamp holder, insulated boldy, angle holder pVC/Polycarbonated type with back plate complet all as specified.

S&F in replacement of 10 watt LED new adore 10WB22 cool day light ball lamp.

S&F ceiling rose surface bakelite 65x50mm two to three terminals.

Supply and fixing exhaust fan heavy duty 300mm with louver, AC single phase 230 volts 900 RPM fixed on wall with necessary electrical connections with 3 core copper flexible multistranded cable of suitable size and connecting with ceiling rose including making hole/niche in wall to fix the fan and necessary arrangement for fixing such as frame,nuts,bolts and washers all as required at site.

Material and labour for house service bracket (hook type) complete with 3 mtrs long GI pipe 40mm dia, medium grade, 2 Nos 90 degree MS hook and stay or gay on the wall by grouting cement mortar and make good on all disturbed surfaces complete.

Material & Labour for one twin core cable flat or circular, 1100 volts grade heavy duty cable, PVC insulated, with stranded aluminium conductor, size 10 Sqmm served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating in service hangers not more than 1 metre apart including 4mm GI suspension wire.

S&F in sheet metal enclosure MCB DB double door 4 ways with 200 Amps rated bus bar SPN complete all as specifed and direcetd.

S&F MCBs 6-32 amps rating and to be housed in DBs catered here in before complete all as specified and directed (Note :- Proper and suitable size cable lugs to be fixed with MCBs are deemed to be included in unit rate of each MCB of any rating)

Ditto all as above but single pole and neutral 6-32 Amps 'C' series socket point on same board.

Supply and fixing bracket for street light fitting fabricated with 1200 mm long and 40 mm bore medium grade GI pipe bent to shape as required and fixed in position including necessary clamps,nuts,bolts & washer.

Supply,fixing and connecting new generation energy saving environment friendly long life LED street light made up of pressure die cast aluminium housing with high power LEDs as light source and lens embedded PC cover with IP-66 protection and impact resistance of IK07 having 45 watt 5700K LED with prewired and necessary mounting GI bracket and making necessary electrical connection.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common saft filling in alternate layers and electrode connection by using earth lead GI wire 4mm dia by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and other end of the earth wire connected to main switch board protected by galvanised iron light grade pipe 15mm bore in wall/floor/and GI Pipe 20mm bore light grade for watering with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC pit cover including necessary excavation and earth work in any type of soil, returning slurry approved soil and disposed of surplus soil to a distance not exceeding 50 Mtr away all as shown in Electrical Plate No 3 of SSR 2009( Part-I).

S&F Bell push, flush type, 5 amp

S&F Bell, AC, 230 volts, single pole

S&F ceiling fan regulator electronic type 240 volts ISI marked 5 steps and connecting all as specified.

Supply and fix surface and wall mounted E- LITE LED curve with wide angle profile high lumen with efficiency of 100 lumens batten extruded aluminium housing provided for efficient heat dissipation with polycarbonate housing &integrated electronic driver including LED tube light 20 watt 4 feet complete all as specified .

S&F sheet metal enclosure MCB DB double door 8 ways with 200 Amps rated bus bar SPN complete all as specified and directed .

Supply and fix LED light fitting mirrer type with high out put diffuser 2 feet 10 watt 220 v AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

M & L for submain wiring with two runs of PVC insulated multistranded copper conductor of size 6 sqmm cable single core 100 volts grade and one run of earth continuity conductor cable of 6 sqmm solid strand cable drawn in and incl 30/32 mm PVC casing caping complete all as specified and as directed .

Supply and fix electric water heater storage type steel body with copper inner tank and eating element upto 2 KW capacity 25 litre BEE 5 star rated complete with all accessories such as safety valve thermostate NRV connection piece etc .

Supply & fix exhaust fans AC single phase 230/240 V of size 300 mm sweep with louvers .

Material & Labour for one twin core cable flat or circular, 1100 volts grade heavy duty cable, PVC insulated, with stranded aluminium conductor, size 10 Sqmm served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating in service hangers not more than 1 metre apart including 4mm GI suspension wire, and including taking down of unserviceable service connection.

supply & fixing ceiling fans 1200mm sweep complete including provision of PVC insulated copper multi starnded three core flexible cable for making necessary electrical connections from ceiling rose to connector including testing complete all as specified Make :Bajaj/ CG

Supplying, laying or fixing, jointing and testing LT under ground electric power cable crossed linked polyethylene (XLPE Cable) insulated, two or more core galvanised steel strip or wire armoured, ISI-7098 Mark, with aluminium conductor mutli stranded, heavy duty 1100 Volts grade of 10 sqmm 2 core size, complete all as specified laid in trenches / laid under floor or fixed naked with walls/ on poles/ in ducts / in GI pipes etc. complete all as specified and directed. (Note :- Excavation, earth work, sand cushioning, protection bricks/ tiles / block, and pipe shall be measured and paid separately under appropriate items).

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth, for foundations etc. or for shafts, well cess pits, manholes, pier holes, laying of pipe and cables etc. but not exceeding 10 sqm on plan including dressing /trimming sides and levelling/grading & ramming bottom of excavation and getting out in soft/loose soil complete all as specified.

Returning, filling in , including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in soft/oose soil complete all as specified.

Removing excavated material (soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the strating point complete all as specified.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in tenches below and around under ground cable including spreading and levelling complete as specified and directed.

M&L laying well burnt old size bricks, sub calss "B" bricks, straight or curved on plan, laid flat with width equal to length of brick, laid dry over electric cablefor protection all as specified.

M/s Brahamaputra Wood Industries