Construction of 11 KV underground feeder (By Trenchless Technology) for giving connection to MDDA housing society near ISBT emanating from 33/11 KV S/s Turner road on partial turnkey basis under EDD (South), Dehradun.

Amount

Material

11 KV Vacume Circit Breaker, 3 Phase, 50 HZ (Scada Compatible).

11 KV Cable end termination J/Kit for 3 x 300 sqmm cable (O/D)

11 KV Cable end termination J/Kit for 3 x 30 sqmm cable (I/D)

Al Lugs 300 sq mm

Stay clamp for ST Pole SP-33 with N&B

PP & Clamp for ST Pole SP-33 with N&B

PG Clamp suaitable for cable connecting and jumpering

Cable Holding clamp with N&B

Al Lugs suitable for Dog

GI Strip of size 35 x 6 mm

11 KV straight Througgh cable jointing kit 3 x 300 sqmm

Cartage and Errection

Cartage of STP SP-33 Pole from central store to work site including loading and unloading

Cartage of Stock Material from central store to work site including loading and unloading

Mannual Cartage of STP SP-33 Pole from road site to work site including loading and unloading

Mannual Cartag of Stock Material from road site to work site including loading and unloading

Fabrication of MS Channel, Angle Iron after cutting in required size with drilling of holes upto good finish.

Ereection of STP SP-33 Single pole support including excavtion of foundation of pit of size 0.9 x 0.6 x 1/5th of length of pole in mixed soil for LT/HT support with back filling of earth and grouting of pole supports with cement concrete in size 0.45 x 0.45 x 1/5th meter length of support with CC Ratio 1:4:8 with cement, course sand and stone ballast. Muffing/Plinthing of pole 300 mm above ground level of size 0.45 x 0.45 mm in CC Ratio 1:3:6 as per UPCL Construction Manual.

Ereection of STP SP-33 Double pole support including excavtion of foundation of pit of size 0.9 x 0.6 x 1/5th of length of pole in mixed soil for LT/HT support with back filling of earth and grouting of pole supports with cement concrete in size 0.45 x 0.45 x 1/5th meter length of support with CC Ratio 1:4:8 with cement, course sand and stone ballast. Muffing/Plinthing of pole 300 mm above ground level of size 0.45 x 0.45 mm in CC Ratio 1:3:6 as per UPCL Construction Manual.

Fixing of MS Earth Rod including excavation,inserting of earth rod in soil and connecting of earth wire.

Fixing and grouting of stay set including digging of pit in size of 1.2 x0.6 x0.6 mtr of CC 1:4:8 including nozzeling, fixing, tensioning and tightening complete.

Painting of New/Existing poles including one coat primer and two coat silver paint and Red asian paint of superior quality on upper side of the pole

laying of 11 LV cable in HDPE Pipe including cst of HDPE Pipe (atleast 160 mm Outer Dia, 6 mm thickness) at 2 mtr depth by horizontal Directional Drilling (HDD) method.

Making of open Trench in Rockey area including laying of cable in trench at 2 mtr below ground level and connecting HDPE pipe

Laying of cable for pole rising etc.

Supply and laying of HDPE pipe 160 mm outer dia 6 mm thickness

Supply and fixing of GI Pipe (with socket) 6 or 8 inch dia at point of road crossing ,cable rising etc.(B class Jindle make)

Supply and fixing of earthing for cable at different pole structure by 450x450x10 mm GI Plate vertically 3 m below the ground level with alternate layer of charcoal and salt atleast 200 mm thick around connected with GI strip running till top of pole complete

Fixing of MS Channel,MS Angle and all accessories on new/Existing Single pole

Fixing of MS Channel,MS Angle and all accessories on new/Existing Double pole

Making of bus bar arrangement with 11 kv 1C x 300 sq mm cable for end termination connection and jumpering including cost of 11 KV 1C x 300 sqmm cable

Filling and fixing of 11 kv End termination kit( I/D O/D)

Filling and fixing of 11 kv Straight through cable jointing kit

Mounting and fixing of lightening arrestor set (3Nos) including making all connections.

Earthing of lightening arrestor set (3Nos) by GI Strip of size 35 x 6 sqmm

Fixing of accessories insulators/clamps etc.

Making pit of size 5x2x2 mtr for filling of straight through joint kit with back filling ramming and compaction upto complete restoration

Erection of 11 kv VCB Feeder 350/500 MVA,400/200/5 A,110 V AC Panel with fixing and connection complete

Supply and fixing of route marker

Supply and fixing of Danger/number/name plate

Laying of LT XLPE Al conductor unarmoured power cable size 1 x 35 sqmm

Laying sagging jumpering and stringing of ACSR Dog conductor

Civil Work

Civil work for extention of VCB panel Room for new feeder

Description of Work / Item(s)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. --- All kinds of soil.-----------

Filling available excavated earth….

Supplying and filling in plinth with Jamuna sand under floors including. Watering, ramming consolidating and dressing complete.

Earth filling under floor and in sub-station area including cost of earth. Earth to be obtained from outside the corporation area including its cartage and ramming, watering, dressing in 20 cm's thick layers including cost of earth with all lead and lift etc.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :-- 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 5.1.2 :- 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) --------

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.Thermo-Mechanically Treated bars.

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for : Weather shade, Chajjas, corbels etc., including edges.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc. and removal of form for : Edges of slabs and breaks in floors and walls. Under 20 cm wide

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level excluding cost of centering, shuttering, finishing and reinforcement : ---1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Add or deduct for plaster drip course/ groove in plastered surface.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in:- Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with F.P.S. brick of class designation 75 in foundations and plinth in. cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in :--- Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with F.P.S. bricks of class designation 75 in foundations and plinth in. Cement above plinth level up to floor V level... Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab upto 0.50 sqm

Extra for providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge. Granite work.

Providing and fixing fly proof galvanised M.S. wire gauze to windows and clerestory windows using galvanised M.S. wire gage with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm. With 12 mm mild steel U beading.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 100x63x4 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 150x10 mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium casement stays ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets,gates and similar works.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1- 40mm thick with 20mm nominal size stone aggregate

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 11.13.1- 40 mm wide and 4 mm thick.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. 75 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. 15 mm cement plaster on rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.---12 mm cement plaster

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.---6mm Cement plaster finished with a floating coat of neat cement 1:3.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade 13.41.1 New work (two or more coats) over and including priming coat with cement primer.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Forming groove of uniform size from 12x12mm and upto 25x15mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) :--For fixed portion---Powder coated aluminium

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately).---- Powder coated aluminium

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge . (Cost of aluminium snap beading shall be paid in basic item)with float glass panes of 5.50 mm

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper onductor single core cable in surface / recessed medium class PVC conduit, with Modular type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.Group B

Supplying and fixing followingModular type switch/ socket on the existing switch box/ cover including connections : 5/6 amps switch

Supplying and fixing following Modular type switch/ socket on the existing switch box/ cover including connections : 3 pin 5/6 amp socket outlet

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on ...... providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required. (1.32)

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing following rating, four pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

supply and fixing following way, single pole and neuteral, sheet steel, MCB distribution board cosumer unit, 240 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, hinged frount acrylic cover for the MCB knobs, detachable gland plate, interconnection, phosphatized and powder painted including earthing etc. as required. ( But without MCB/RCCB/Isolator )

Earthing with GI earth wire

P/F 6 SWG GI loop….

Supply and fixing of 1200 mm size ceiling fan with regulator complete of Khaitan, Bajaj

S/F of factory wired, HPF box type flourcent tube light fitting suitable for 1 x 40 watt

S/F Exhaust fan of Bajaj or approved quality

Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method, to attain superior smooth finish using PU or equivalent moulds, laid in required Grey colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per manufacturer’s specifications & direction of Engineer -in-Charge: (a) 80 mm thick c.c. paver block of M-30 grade with approved color design and pattern.

Providing and fixing 1st quality Somany Digital wall tiles 300X450 mm size conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Engaging/S of suitable beldar for different type of works

Hi Tech Power Solution

Creative Entrepreneurs LLP

P M ELECTRICAL COMPANY

Creative Entrepreneurs LLP