C/O GOS MESS (07 SUITES) AT BN HQ JARULTOLI KUMARGHAT UNDER SHQ BSF PANISAGAR

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed ,within a lead of 50m.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete:With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.:With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shttering - All work up to plinth level:1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Providing and fixing on wall face SINGLE SIDE WOODEN TEXTURE HPL CLADDING of approved make

Centering and shuttering including strutting, propping etc. and removal of form work for :Foundations, footings, bases for columns

IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax in Rs. P

Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category in Rs. P

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering & shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases of columns etc. for mass concrete.

Centering & shuttering including strutting, propping etc. and removal of form work for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering & shuttering including strutting, propping etc. and removal of form work for Suspended floors, roofs, landings, balconies and access platform.

Centering & shuttering including strutting, propping etc. and removal of form work for Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centering & shuttering including strutting, propping etc. and removal of form work for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering & shuttering including strutting, propping etc. and removal of form work for Stairs, (excluding landings) except spiral-staircases

Steel reinforcement for R.C.C. work including traightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo- echanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note :- Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement..All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

Modified estimate cost after using correction factor on DSR 23 on account GST @ 0.973 from item sr no 01 to 132

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. `Cement mortar 1 : 4 (1 cement : 4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class Teak Wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Float glass panes 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) On one side only

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete :20 mm dia

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete 25 mm dia

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300mm x 16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 150x10 mm

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 75 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete Twin rubber stopper

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. horizontal top srde. Door shutter. The double skinned single leaf partially insulated fire rated door shutters shall be consisting of minimum 50 mm thick and having box like structure, slots cut and holes punched, for fixing of hardwares with stiffners as per lS: 16074 including resrn bonded mineral wool / ceremic wool infill material of minim

TOTAL AMOUNT Without Taxes in Rs. P

um density 96 kg/cum. Door leaf shall be provided with vispn panel, having maximum area of 0.06 sqm, of 120 minute fire rated minimum 6 mm thick clear borosilicate glass pane fixed with clip-on arrangement and fire rated c€ramic tape having minimum size 13x2 mm to be lixed all around the glass on both the sides. The intumescent seal of minimum size 15x1.5 mm or oI size as per test evidence shall be flxed on all the three edges of the door leaf. The door shutter shall be mounted on the frame with SS 304 grade ball bearing butt hinges as per EN 1935 2002 or butt hinges as per lS 12817, of minimum size 100x75x3 mm @ 5 numbers hinges upto 24OOmm heig or as per test evidence, whichever is more, fixed with M6 25 screws. All doors shall be factory prepared for receiving appropriate hardware and provided with necessary reinforcement for hardware accessones. 30 mm thick pre laminated PVC door shutters

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 Part 1 to 14, plastic packers, plastic caps and necessary stainless ste screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.Wire mesh /Glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 Part 3 (ii) Sites with structure height more than 20m for all wind speeds Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 Part 1 to 14, plastic packers, plastic caps and necessary stainless ste screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.Wire mesh /Glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 Part 3 (ii) Sites with structure height more than 20m for all wind speeds Fixed window / ventilator without mullion / transom. Using R1 series with frame (33 mm & above) x (35 mm & above). (Height upto 0.90 metre)

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes. .

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to

TOTAL AMOUNT With Taxes Rs. P Rs. P

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources).

Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Litre

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing & fixing on wall face unplasticised -Ragid PVC rain water pipes conforming to IS ; 13592 Tyape A included jointing with seal ring conforning to IS ; 5382 leaving 10 mm gap for thermal expansion.a)110 mm diameter

Providing, fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised - Rigid PVC rain water pipes conforming to IS ; 13592 Type A including jointing with seal ring conforming to IS ; 5382 leaving 10 mm gap for thermal expansion.a)Coupler-110mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. b)Bend-87.5deg-110mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. c)Shoe-110mm shoe

Providing and fixing to existing door frames. : 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames.

Providing & fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1cement : 4 coarse sand) and making good the wall etc. complete.110mm dia

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighting not less than 440 grams.

15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 coarse sand)

6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand)

Neat cement punning

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

For Exterior wall - Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment).(Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quallity conforming to IS: 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and Haying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm

Providing and Haying Vitrified tiles in floor in different sizes (thickness to be specifi

ed by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.

Providing and fixing C.P.brass bottle trap 32mm size bottle trap of approved quality & make as approved by Engineer-in-charge.

Providing and fixing C.P.brass Single lever telephonic wall mixer of approved quality & make as approved by Engineer-in-charge.15 mm nominal bore.

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe 40 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600mm

Providing and fixing toilet paper holder :C.P. brass

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size ) including necessary plaster and pointing in cement mortar 1:4(1cement: 4 coarse sand):100 mm dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.15 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cut

ting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.20 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External 32 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External 40 mm dia. nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :25 to 40 mm nominal bore

Providing and fixing brass stop cock of approved quality.15 mm nominal bore

Providing and fixing brass stop cock of approved quality : 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):32 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 40 mm nominal bore

Providing and fixing ball valve (brass) of approved quality complete :20 mm dia. nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end):40 mm nominal bore Horizontal

Providing and fixing uplasticised PVC connection pipe with brass unions :15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Cutting holes upto 30x30 cm in walls including making good the same :With common burnt clay F.P.S. (non modular) bricks

Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.

Making chases upto 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 100mm nominal inner dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : 150 mm nominal inner dia. Pipes.

Providing and laying cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) alround S.W. pipes including bed concrete as per standard design: 100mm diameter pipe

Providing and laying light duty non-pressure NP2 class R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete: 450 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregrate 40mm nominal size ) inside plastering 12 mm thick with cement mortar 1:3 (1 Cement : 3 coarse sand) finished with floating coat of neat cement & making channels in cement concrete 1:2:4 mix (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80cm and 45cm deep including C.I. cover with frame (light duty) 455x610mm internal dimensions total weight of cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15 kg) Withcommon burnt clay FPS (non modular)bricks of class designation 7.5

Extra for depth for manholes Size 90x80 cm Withcommon burnt clay FPS (non modular)bricks of class designation 7.5.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : for fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with CI brackets,15mm C.P. brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fittings & brackets,cutting and making good the walls wherever required.White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

BoQ_Ver3.0

Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth course of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45, 1.20 and 1.45 Kg per square metre of area respectively, second and fourth courses of roofing felt type 3 grade I conforming to IS : 1322 (Hessian based self finished bitumen felt) , sixth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm including preparation of surface but excluding grading, complete.

1 :5:10 (1 cement: 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

SITC of water protected outdoor (Weather proof) hut type compartmentalized type double door cubical panel both side opening having depth up to 600 mm suitable for 415 Volt, 3 phases, 50 Hz made out of 2mm thick CRCA sheet with required hardware duly painted with powder coated . Panel having separate detachable gland plate, end termination as per cable of size, angle iron base frame made out of 50mmx50mmx6 mm angle iron of suitable size of the feeder pillar (minimum height 60cm), hinged door, led pilot light for phase indicator (R,Y,B) on top and VAF Meter, 250A/415V 4 strip aluminum bus bar duly PVC sleeved, connection inter– connection with 25% extra current carrying capacity bus bars to MCCBs spreader links and with solid copper conductor cable 10 sq.mm / solid aluminum rod for connection to MCBs and heavy duty connectors of required current carrying capacity to be fixed back side. Incoming/outgoing cable connections etc complete as required i/c dismantling the existing feeder pillar and UG cable. (Panel should be as per design & drawing approved by Engg in charge).

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Add Cost Index @60.00% on SR&DR

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular metalic type switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

i) Group A

II) Group B

iii) Group c

Wiring for twin control light point with 1.5 Sqmm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, 2 way modular metalic type switch, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

i) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

ii) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

iii) 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

iv) 2 X 10 sq. mm + 1 X 6 sq. mm earth wire

v) 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

3 x 1.5 sq. mm

3 x 4 sq. mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in Surface /recess including cutting the wall and making good the same in case of recessed conduit as required a) 25 mm

Providing and fixing following modular metalic type switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

i) 5/6 amps switch

ii) 3 pin 5/6 amp socket outlet

iii) 15/16 amps switch

iv) 5 pin 15/16 amp socket outlet

iii) Telephone socket outlet

iv) TV antenna socket outlet

Providing and fixing following size/ modules, GI box alongwith modular base & cover plate for modular metalic type sw

itches in recess etc. as required.

i) 1 or 2 Module (75mmX75mm)

ii) 6 Module ( 200mm X 75 mm)

iii) 8 Module ( 125mm X 125 mm)

iv) 12 Module ( 200mm X 150 mm)

Providing and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular metalic type socket outlet and 15/16 A modular metalic type switch, connections etc. as required.

Providing and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Providing and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular metalic type switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required.

100 A, 16 KA,TPMCCB

125 A, 16 KA,TPMCCB

200 A, 25 KA,TPMCCB

Providing and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way , Double door

Providing and fixing following way, horizontal type three pole and neutral, dheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

iii) 6 way (4 + 18), Double door

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. For 14 way, Double door SPN MCBDB

Providing and fixing Cable End Box (Loose Wire Box)suitable for following triple pole and neutral, sheet steel, MCB distribution board,415 Volts,on surface/recess,complete with testing and commissioning etc.as required. a) For 6 way,Double door TPN MCBDB

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling a

nd dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately Powder coated aluminium (minimum thickness of powder coating 50 micron)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete Upto 5mm depth and 5 mm width

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

Providing and fixing of lightning conductor finial, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing 5 amps to 32 amps rating,240/415 volts,"C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections testing and commissioning etc.as required.

i) Single Pole

ii) Double pole

ii) Triple pole and neutral

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2 X 10 sq. mm (19mm

4 X 50 sq. mm (35mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. a) 120 mm dia (OD-120 mm & ID-103 mm nominal)

(A)Supplying,installation,testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following,complete in all respects,as required: (Terrace Pump) (B)Horizontal type,multistage centrifugal,split casing pump of cast iron body &bronze impeller with stainless steel shaft mechanical conforming to IS:1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts,3 phase,50 Hz,AC supply with IP55 class of protection for enclosure,horizontal foot mounted type with Class-'F"insulation conforming to IS-325 (D) M.S.fabricated common base plate,couppling,coupling guard, foundation bolts,etc.as required (E)Suitable cement concrete foundation duly plastered and with anti vibration pads.

450 lpm at 35m head

2 X 10 sq. mm (19mm

4 X 50 sq. mm (35mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. a) 120 mm dia (OD-120 mm & ID-103 mm nominal)

Providing laying, testing & commissioning of 'C'class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows tees,flanges,tapers,nuts bolts, gaskets etc.and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required.

2 X 10 sq. mm (19mm

4 X 50 sq. mm (35mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. a) 120 mm dia (OD-120 mm & ID-103 mm nominal)

100 mm dia

4 X 50 sq. mm (35mm)

80 mm dia

65 mm dia

40 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze / gunmetal seat duly ISl marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required:

Providing,installation,testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket,Gl bolts,nuts,washers etc.as required.

Supplying & fixing of rectangular SMC junction box with shock and rust proof with 6 amp SP MCB, terminals, plastic gland, lugs, busbar and other required accessories etc. as required Engineer In Charge. Make Syntex cat ref. GSJB 1414 or equivalent.

Supply and installation of four pole mccb unit with enclosure 160 amps and making connection with inverter incoming supply and outgoing supply battery by suitable size thimbles on all cable terminations and fixing the enclosure with rawal plug or anchor bolt with nuts etc. earthing to the enlosure should be made as per direction of engr in charge at site as reqd.

Supply and installation of four pole SWITCH DISCONNECTOR UNIT rated for 160 amps with HRC fuses along with enclosure and making connection with inverter and battery by suitable size thimbles on all cable terminations and fixing the enclosure with rawal plug or anchor bolt with nuts etc. earthing to the enlosure body should be made as per direction of engr in charge at site as reqd.

Providing,installation,testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel,Grade 304,sheet with 3 mm dia holes with stainless steel flange etc.as reqd.

Providing and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to lS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS:1258520 mm nominalinternal dia gun metal globe valve &nozzle.Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun meta valve & M.S.Pipe and socket etc.as required

SITC of three phase solar ACDB box for 12 KW with IP 65 enclosed SPD single phase 40 Ka type-2 Make Alpro/Elmex/Phenix contact/Havells .

Providing &fixing of pressure switch in M.S.pipeline including connection etc.as required.

Providing and fixing of fire brigade connection of cast iron body with gun metal male instantenous inlet couplings complete with cap and chain as reqd.for suitable dia MS pipe connection conforming to IS 904 as required

2 way-100 mm dia M.S.Pipe

Providing and fixing air vesse made of 250 mm dia,8 mm thick MS sheet,1200 mm in height with air release valve on top and flanged connection to riser,drain arrangement with 25 mm dia gun metal wheel valve withrequired accessories,pressure gauge and painting with synthetic enamel paint of approved shade as required.

S/I/T/C of 4.5 kg capacity CO2 type fire extinguisher duly ISl marked lS:15683 operating temperature(-30)°C to(+60)°C, steel body duly filled with CO2 gas,Wheel type release valve, Delivery hose horn and locking arrangements,with wall mounting bracket complete in all respect etc as required.Make-FlameKlog/Ceasefire/ Kenex Fire/ Safex

Supply,installation,testing and commissioning of 100 mm dia Bourden type,pressed Steel MS casing dial type Pressure Gauge including brass isolation valve and siphon pipe having caliberation 0 -16 Kg /cm2 of complete etc.as required.

S/I/T/C of 6 Kg capacity ABC stored pressure type fire extinguisher duly ISI marked IS: 15683 operating temp (-30 deg C to +60 deg C ) filled with MAP 90% powder, squeeze grip, release valve, discharge pipe, locking arrangement, pressure guage, operating mannual and bracket complete in all respect etc as required. Make-FlameKlog/Ceasefire/ Kenex Fire/ Safex

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover

complete with all connections etc. as required

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing and commissioning sector panel suitable for following zones, complete with visualindications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.

Supplying and drawing of cable fire retardant PVC insulated copper conductor cable in the existing surface/recessed steel conduit of following pairs, cores and size including connections and interconnections etc as required.

Speaker cable single pair, 2-core, 1.5 Sqmm

Providing and Fixing of 20 watt Aluminium housing & integrated electronic driver LED batten lighting fixture , envoirmental friendly etc as reqd. Make Havells Model Lumiline Plus or equivent make Wipro/Philips /CG/Havells

Providing and Fixing of 10 watt Aluminium housing & integrated electronic driver LED batten lighting fixture , envoirmental friendly etc as reqd. Make Havells Model Lumiline Plus or equivent make Wipro/Philips /CG/Havells

Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI>70, under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge.Pole Size(0.60x0.60x0.60) CUM. 0.216 per Pole

Cement concrete 1:1.5:6 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) for insttalation/making of 4500 mm LuxMax Delta-N(Cast Iron) Pole (0.6x0.6x0.75)CUM 0.27 Per pole.

Centering and shuttering including stutting, propping etc. and removal of form of : Foundations, footings, bases of columns, etc. for mass concrete.(2x.6x.75+2x.6x.75)=1.8

Steel reinforcement for R.C.C. work including straightening , cutting, bending, placing in position and binding all complete above plinth level.(Thermo Mechanically Treated bars)(4 nos-12 mm Vertical bar each size 1.2mtr ,4-nos-8mm stirrupus bar each-2 mtr) = 10.94 KG Per Pole .

Providing and fixing of 6 watt LED panel round down light LED unique slimest surface panel directly on celing including making connection with 1.5 sq mm FR LS PVC insulated copper conductor single core cable etc as required Make Havells Model Trim clipon or equivent make Wipro/Philips/CG/Havells

Providing and fixing of 18 watt LED panel round down light LED unique slimest surface panel directly on celing including making connection with 1.5 sq mm FR LS PVC insulated copper conductor single core cable etc as required Make Havells Model Trim clipon or equivent make Wipro/Philips/CG/Havells

Providing and fixing of 24 watt LED panel round down light LED unique slimest surface panel directly on celing including making connection with 1.5 sq mm FR LS PVC insulated copper conductor single core cable etc as required Make Havells Model Trim clipon or equivent make Wipro/Philips /CG/Havells

Providing and fixing of 40 Watt energy saving long life corrosion resistant , vertical /horizontal surface mounting pressure die -cast aluminium well glass luminaires with high power LED as light source ,making connection with 1.5 sq mm FR LS PVC insulated copper conductor single core cable etc as required M

ake Havells Model - Stupe Well Glass or equivent make Wipro/Philips/CG/Havellsred.

Providing and fixing of 3 W decorative bed light aluminium base testing commissioning etc as required

Supplying, installation , testing and commissioning of energy efficient surface mounted wall bracket lighting fixture, environmental friendly, energy efficient ready to use pack, completed with all accessories including 9 watt LED buld suitable for wall bracket etc. as required.

Providing and fixing of Globe Brass 9 Watt Celing Crystal Chandelier, that hangs from the ceiling testing commissioning etc

Providing and fixing of Modern Crystal Hangir Glass Chandelier that hangs from the ceiling testing commissioning etc

P/F 25 W Track mounted LED light with high power COB LED to provide focussed light with wire complete with connection, testing commissioning etc as required. Make Havells Model - UNECO Track Light or equivent make Wipro/Philips/CG /Havells.

P/F 1 MTR Track Model One metre Track WHT of Havells make with wire complete with connection, testing commissioning etc as required. and similiar Make of Bajaj/Havells/Philips

P/F Surface Mounted LED Strip with adapter make Havells with wire complete with connection, testing commissioning etc as required. and similiar Make of Bajaj/Havells/Philips

Supply, Installation, Testing and Commissioning of 1200 mm sweep, Decorative, ceiling fan , 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, and all remaining accessories including safety pin, nut bolts, washers, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. Make - Havells model Fusion Prime ES or equivalent make Crompton/Bajaj/Usha/Standard

Supplying and fixing of 250 mm, plastic type exhaust fan suitable for single phase, 50 Hz, 230 volts, AC supply in including making hole to suit the size & fixing of louver / shutter including connections etc. as required. Make- Havells model Venti Air DX or equivalent makeCrompton/Bajaj/ Usha/ Standard

Providing and fixing of 25A motor starter fixture complete with all accessories .complete as required. Make Havells ACWSMXW251 (Havells) or equivalent make Legrand/Schneider/ Siemens/ L&T

Providing and fixing USB Charging Socket on the existing modular plate & switch box excluding modular plate as required. Make- Havells SAP Code ACWKGXW002 or equivalent make Legrand/Schneider/ Siemens/ L&T

Supplying,installation testing and commissioning of 300 mm sweep wall fan suitable for single phase, 50 Hz, 230 volts, AC supply colour- White / Brown / Ivory etc as required. Havells Make D Zire or equivalent makeCrompton / Bajaj /Usha/Standard

Providing and fixing of 25 ltr electric storage water heater with fasteners , bolts and washers including with connection, testing commissioning etc as required Make Standard model -Ameo or equivelt make Havells/ Bajaj/ Racold

Supplying & installation of 2 Ton Split A.C ,High wall having rated, 5 Star rating, consisting of one out door condensing unit, remode control, Airconditioning pipeline refrigerant kit and one indoor air handling unit with following parameters for operation on 230 V/ 50 Hz. single phase AC supply complete with surrounding AIr circulation cooling capacity to deliver 580 cfm to 750 cfm and filteration i/c testing, and commiossioning complete etc as required. (Make- Blue star/Voltas/Hitachi/Godrej)

Supplying, installation , testing and commissioning of wall mounted 5 KVA Voltage stabilizer suitable for 1.5/2 Ton A.C. having input range 130-280 volts and output 230 Volts, 50 Hz single phase AC supply complete with time delay, high & low voltage protection and product warranty as per manufacturer complete etc as required. Make -V Guard Model- iD4 Ace or equivelent make Luminous/ Microtek/Aulten/V Guard

Supplying installation testing and commissioning of refrigeration pipe including cutting of wall and fixing with suitable saddles or clamps, providing suitable sizeof sleeves for passing refrigerant pipe from indoor to outdoor unit including making necessary arragement etc complete s required a) Copper pipe

SITC of wall mount Chimney with 10 speed motor fix on wall of kitchen inculding making all opening for exhaust air outlet and mounting by suitable size of nit bolt & washers including making connection through FRLS multi core copper wire as per the OEM specification at site etc. upto the satisfaction of Engineer incharge.Make- IFB Model No- IFB EC4-BS-HS- 90 BF-BLDC or equivelent make Feber/ Elica/ Hindware/ Glen.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing of mono colour 50 W LED Flood Lights made up of pressure die cast aluminium housing flood light with PC diffused lens enclosure over LED for glare free light Havells make make Jeta Quanto Plus or equivelent make Crompton/ Bajaj / Wipro

Providing and fixing Glow sign Board (letter height 10 inch ) with ACP sheet background, stainless steel fabricated letters, acrylic backing, and internal LED Lighting to provide glow effect with reflection on ACP sheet complete etc as per direction of engineer in charge.

Providing and fixing of 10 Watt LED garden light IP65 Bollardseries with excellent light output through sleek PMMA window acts as an imposing street furniture, silient observer and giving light, diffuser at the upper portion adds functional value into landscape environment and erection of base 400mmX400mmX800 mm of cement concrete of 1:2:4 ratio complete etc as per direction of engineer in charge. Make- Havells model Mount LED Bollard or equivelent make Hakke/ Luminex/Waaree

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Supplying & laying of G.I. pipe of 40 mm dia (medium duty ) G.I pipe in floor/wall/road for protection of UG cable including cutting the wall/floor/metalled road and making good the same as required.

Providing and fixing 2900 mm LuxMax Elysee Pole (Cast Aluminium) Pole with double arm Bracket(L Bracket of length 700mm ) ,LuxMax fixture (LuxMax-PT-164-M) With 25 Watt Make-Twinkle, including connection with 3x1.5 sq mm Cu FRLS wire from MCB to Pole led Light. Make of wire-Havells/finolex/Polycab (Final approval issued by Engineer in Charge) Make-Twinkle or equivalent K-lite/Tubit/jelco

Providing and fixing of 45 Watt decorative post top faesthetically designed pathway lightning system with integrated light having asymmetric light distrbution IP66 rating and aluminium die-cast housing Make Wipro cat ref LP09S-501-XX-57-XX including making connection or equvalent make of Havells/Philips/Crompton

Supplying & laying of one number XLPE insulated and PVC sheathed Armoured power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe/ Open duct as required.

i) 2 X 10 sqmm

ii) 4 X 50 Sqmm

iii) 4 X 70 Sqmm

Providing and fixing ofHJT 730Wp Bifacial Double Glass Half Cell Solar Panel including rooftop mounting structure fixed on suitable size horizontal rails with vertfical support membrs through a set of clamps including base of the rails on existing roof etc as required as per direction of engineer in charge of make LOOM SOLAR/WAREE/DEVSOL/Reliance New Energy (Pro-XL & Pro-L Series) OR MNRE CERITIFIED MAKE AS PER SPECS GIVEN BELOW MODEL HG730H-66HC12B OF LOOM SOLAR Maximum Power(Pmax/W) - AT STC CONDITIONS - 730WATTS AND NMOT - 557 WATTS Operating Voltage(Vmp/V) - 42.32 VOLTS DC Short-Circuit Current(Isc/A) - 18.35 AMPS Open-Circuit Voltage(Voc/V) - 50.37 VOLTS DC

Supply installation testing commissioning of Galaxy 6G EU ONGRID HYBRID 12 KW-48V three phase invertor for lithium-ion battery for battery charging/discharging support storing energy from solar/ power grid/diesel generator of Make cellcronics or compatible make from iNVERGY/Deye/GOODWE/MUSCLEGRID etc with following undermentioned functionality Inverter should have Colorful touch LCD, IP65 protection degree. INVERTER Should output Pure sine wave AC voltage inverter should have surge capacity and PV input capacity 16500W Maximum Load Capacity & 24000W Solar Capacity respectively TIME SCHEDULE MODE FOR BATTERY CHARGING 6 time period for battery Charging/ discharging. BATTERY CHARGING CURRENT CAPACITY Max. Charging/discharging current of 280A INVERTER MAX EFFICIENCY SHOULD BE MORE THAN OR EQUAL TO 95% MPPT CHARGER UNIT EFFICIENCY SHOULD BE MORE THAN OR EQUAL TO 95% INVERTER SHOULD HAVE INTEGRATED PROTECTION ON FOLLOWINGS: - DC Polarity Reverse Connection Protection, AC Output Overvoltage Protection, AC Output Overcurrent Protection,AC Output Short Circuit Protection, Thermal Protection,DC Terminal Insulation Impedance Monitoring,DC Component Monitoring, Ground Fault

Current Monitoring Power Network Monitoring, Island Protection Monitoring, Earth Fault Detection,DC Input Switch Overvoltage Load Drop Protection, Residual Current (RCD) Detection, Surge protection level Surge Protection TYPE II(DC), TYPE II(AC)

BoQ_Ver3.0

Providing & fixing Health Faucet with 8mm dia, 1M long PVC tube and wall hook. Make: Jaquar; Cat No. ALD -593N/approved equal make.

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

SITC of 250 Amp Four Pole rotary type On load Changover suitable manually operation and making connection with suibable size thimbles/ lugs on cable termination with terminal spreaders in existing cubicle panel board including drilling holes in panel, making connections etc as required. Make Havells Itemd code IHCNFO0250 or equivelent make L&T /Siemens/Legrand

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Civil work

Elect work