ESTABLISHING CENTER FOR E LEARNING IN KUHS

Amount

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

PROVIDING AND FIXING LUXURY VINYL TILE STRIP OF SIZE 6"X36" AND 1.5MM THICK ON PLASTERED FLOOR SURFACE USING VINYL FIXING SOLVENT AND VINYL OF APPROVED COLOR ALL COMPLETE ETC AS PER DIRECTION OF ENGINEER IN CHARGE<br>

PROVIDING AND FIXING 5MM THICK THEATER CARPET AFTER FIXING 1/2 INCH x 2 FOAM FIXED ON PLASTERED FLOOR SURFACE USING carpet FIXING SOLVENT AND carpet OF APPROVED COLOR ALL COMPLETE ETC AS PER DIRECTION OF ENGINEER IN CHARGE

Supplying and fixing of 69mm thick USG Partition system components. This includes fixing of sheetrock brand ST 55 Floor and ceiling Track (0.55mm BMT, 50mm wide & havingtwo flanges of 32mm each) to the RCC Floor and slab with approved Fasteneres @600mm centres respectivly. The Shetrock Brand ST 55 wall Studs (0.55 mm BMT, 48mm wide with lips, ribs & having one flange of 34mm and other of 36mm). The wall studs are placed at 610mm centres in Floor and Ceiling Tracks. 9.5mm thick Fiberock Panel (confirming to ASTM C 1278) is screw fixed vertically to bot sides of wall stud with 25mm long Drywall Screws at 300mm centres. The screw fixing of Fiberock Panels to the metal framing at the periphery, openings and cut edges should be at 150mm centres. The horizontal & vertical joints of the Fiberock Panels on both sides of the metal framework must be staggered so as to avoid through and through joins. All the joints to be tapped & finished with 50mm wide sheetrock Brand Paper tape & Sheetrock brand . All Purpose Joint compound conforming to ASTM C475.The rate excluding cost for putty work and painting work.

Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge

Refixing the false ceiling using existing tiles and supports including providing additional channels and supports for the grid to ceiling using necessary fittings to provide sufficient fixity to the false ceiling etc. As directed at site.The rate includes cost of all materials, labour charges, scaffolding etc. all complete as per the direction of engineer in charge

internal room acoustics with perforated calcium silicate board 8 mm thick(2x2 tile) and polyester wad wool of 1000 gsm fixed using gi sections .40 mm thick(.30meter spacing horizontal) , intermediate channels .60mmthick(.90meter spacing vertical), perimeter channel .40mm thick and 1 inch screw etc all complete as per the direction of engineer in charge and as per the drawing

internal ceiling acoustics with perforated calcium silicate board8 mm thick(2x2 tile and polyester wad wool of 1000 gsm fixed in the existing grid channels etc all complete as per the direction of engineer in charge and as per the drawing

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting Acrylic Smooth exterior paint of required shade One or more coats on old work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in- Charge.With stainless steel cover plate minimum 1.25 mm thickness

Tino G Kottukapalli